[ Upstream commit e89d120c4b ]
The AMU counter AMEVCNTR01 (constant counter) should increment at the same
rate as the system counter. On affected Cortex-A510 cores, AMEVCNTR01
increments incorrectly giving a significantly higher output value. This
results in inaccurate task scheduler utilization tracking and incorrect
feedback on CPU frequency.
Work around this problem by returning 0 when reading the affected counter
in key locations that results in disabling all users of this counter from
using it either for frequency invariance or as FFH reference counter. This
effect is the same to firmware disabling affected counters.
Details on how the two features are affected by this erratum:
- AMU counters will not be used for frequency invariance for affected
CPUs and CPUs in the same cpufreq policy. AMUs can still be used for
frequency invariance for unaffected CPUs in the system. Although
unlikely, if no alternative method can be found to support frequency
invariance for affected CPUs (cpufreq based or solution based on
platform counters) frequency invariance will be disabled. Please check
the chapter on frequency invariance at
Documentation/scheduler/sched-capacity.rst for details of its effect.
- Given that FFH can be used to fetch either the core or constant counter
values, restrictions are lifted regarding any of these counters
returning a valid (!0) value. Therefore FFH is considered supported
if there is a least one CPU that support AMUs, independent of any
counters being disabled or affected by this erratum. Clarifying
comments are now added to the cpc_ffh_supported(), cpu_read_constcnt()
and cpu_read_corecnt() functions.
The above is achieved through adding a new erratum: ARM64_ERRATUM_2457168.
Signed-off-by: Ionela Voinescu <ionela.voinescu@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: James Morse <james.morse@arm.com>
Link: https://lore.kernel.org/r/20220819103050.24211-1-ionela.voinescu@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 591d2108f3 ]
If a 32-bit kernel was compiled for PA2.0 CPUs, it won't be able to run
on machines with PA1.x CPUs. Add a check and bail out early if a PA1.x
machine is detected.
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d46c742f82 ]
As the possible failure of the kmalloc(), it should be better
to fix this error path, check and return '-ENOMEM' error code.
Signed-off-by: Li Qiong <liqiong@nfschina.com>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b4b18f47f4 ]
This reverts commit b160628e9e.
There is no need any longer to have this sanity check, because the
previous commit ("parisc: Make CONFIG_64BIT available for ARCH=parisc64
only") prevents that CONFIG_64BIT is set if ARCH==parisc.
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8f2c96420c ]
The current power mode change timeout (180 s) is so large that it can cause
a watchdog timer to fire. Reduce the power mode change timeout to 10
seconds.
Link: https://lore.kernel.org/r/20220811234401.1957911-1-bvanassche@acm.org
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f461950fdc ]
Although radeon card fence and wait for gpu to finish processing current batch rings,
there is still a corner case that radeon lockup work queue may not be fully flushed,
and meanwhile the radeon_suspend_kms() function has called pci_set_power_state() to
put device in D3hot state.
Per PCI spec rev 4.0 on 5.3.1.4.1 D3hot State.
> Configuration and Message requests are the only TLPs accepted by a Function in
> the D3hot state. All other received Requests must be handled as Unsupported Requests,
> and all received Completions may optionally be handled as Unexpected Completions.
This issue will happen in following logs:
Unable to handle kernel paging request at virtual address 00008800e0008010
CPU 0 kworker/0:3(131): Oops 0
pc = [<ffffffff811bea5c>] ra = [<ffffffff81240844>] ps = 0000 Tainted: G W
pc is at si_gpu_check_soft_reset+0x3c/0x240
ra is at si_dma_is_lockup+0x34/0xd0
v0 = 0000000000000000 t0 = fff08800e0008010 t1 = 0000000000010000
t2 = 0000000000008010 t3 = fff00007e3c00000 t4 = fff00007e3c00258
t5 = 000000000000ffff t6 = 0000000000000001 t7 = fff00007ef078000
s0 = fff00007e3c016e8 s1 = fff00007e3c00000 s2 = fff00007e3c00018
s3 = fff00007e3c00000 s4 = fff00007fff59d80 s5 = 0000000000000000
s6 = fff00007ef07bd98
a0 = fff00007e3c00000 a1 = fff00007e3c016e8 a2 = 0000000000000008
a3 = 0000000000000001 a4 = 8f5c28f5c28f5c29 a5 = ffffffff810f4338
t8 = 0000000000000275 t9 = ffffffff809b66f8 t10 = ff6769c5d964b800
t11= 000000000000b886 pv = ffffffff811bea20 at = 0000000000000000
gp = ffffffff81d89690 sp = 00000000aa814126
Disabling lock debugging due to kernel taint
Trace:
[<ffffffff81240844>] si_dma_is_lockup+0x34/0xd0
[<ffffffff81119610>] radeon_fence_check_lockup+0xd0/0x290
[<ffffffff80977010>] process_one_work+0x280/0x550
[<ffffffff80977350>] worker_thread+0x70/0x7c0
[<ffffffff80977410>] worker_thread+0x130/0x7c0
[<ffffffff80982040>] kthread+0x200/0x210
[<ffffffff809772e0>] worker_thread+0x0/0x7c0
[<ffffffff80981f8c>] kthread+0x14c/0x210
[<ffffffff80911658>] ret_from_kernel_thread+0x18/0x20
[<ffffffff80981e40>] kthread+0x0/0x210
Code: ad3e0008 43f0074a ad7e0018 ad9e0020 8c3001e8 40230101
<88210000> 4821ed21
So force lockup work queue flush to fix this problem.
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Zhenneng Li <lizhenneng@kylinos.cn>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c351938350 ]
No need to set up rb when no gfx rings.
Signed-off-by: Candice Li <candice.li@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f5994da72b ]
Only amdgpu_get_xgmi_hive but no amdgpu_put_xgmi_hive
which will leak the hive reference.
Signed-off-by: YiPeng Chai <YiPeng.Chai@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9d705d7741 ]
V1:
The amdgpu_xgmi_remove_device function will send unload command
to psp through psp ring to terminate xgmi, but psp ring has been
destroyed in psp_hw_fini.
V2:
1. Change the commit title.
2. Restore amdgpu_xgmi_remove_device to its original calling location.
Move psp_xgmi_terminate call from amdgpu_xgmi_remove_device to
psp_hw_fini.
Signed-off-by: YiPeng Chai <YiPeng.Chai@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ea2aa97ca3 ]
Currently we are assuming a one to one mapping between dmabuf and
GEM handle when releasing GEM handles.
But that is not always true, since we would create extra handles for the
GEM obj in cases like gem_open() and getfb{,2}().
A similar issue was reported at:
https://lore.kernel.org/all/20211105083308.392156-1-jay.xu@rock-chips.com/
Another problem is that the imported dmabuf might not always have
gem_obj->dma_buf set, which would cause leaks in
drm_gem_remove_prime_handles().
Let's fix these for now by using handle to find the exact map to remove.
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220819072834.17888-1-jeffy.chen@rock-chips.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 54249306e2 ]
The error path for the SCSI check condition of not ready, target in ALUA
state transition, will result in the failure of that path after the retries
are exhausted. In most cases that is well ahead of the transition timeout
established in the SCSI ALUA device handler.
Instead, reprep the command and re-add it to the queue after a 1 second
delay. This will allow the handler to take care of the timeout and only
fail the path if the target has exceeded the transition expiry timeout
(default 60 seconds). If the expiry timeout is exceeded, the handler will
change the path state from transitioning to standby leading to a path
failure eliminating the potential of this re-prep to continue endlessly. In
most cases the target will exit the transitioning state well before the
expiry timeout but after the retries are exhausted as mentioned.
Additionally remove the scsi_io_completion_reprep() function which provides
little value.
Link: https://lore.kernel.org/r/20220729214110.58576-1-brian@purestorage.com
Reviewed-by: Martin Wilck <mwilck@suse.com>
Acked-by: Krishna Kant <krishna.kant@purestorage.com>
Acked-by: Seamus Connor <sconnor@purestorage.com>
Signed-off-by: Brian Bunker <brian@purestorage.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 53661ded24 ]
This partially reverts commit d2b292c3f6 ("scsi: qla2xxx: Enable ATIO
interrupt handshake for ISP27XX")
For some workloads where the host sends a batch of commands and then
pauses, ATIO interrupt coalesce can cause some incoming ATIO entries to be
ignored for extended periods of time, resulting in slow performance,
timeouts, and aborted commands.
Disable interrupt coalesce and re-enable the dedicated ATIO MSI-X
interrupt.
Link: https://lore.kernel.org/r/97dcf365-89ff-014d-a3e5-1404c6af511c@cybernetics.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Reviewed-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Tony Battersby <tonyb@cybernetics.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
This reverts commit 23c2d497de.
Commit 23c2d497de ("mm: kmemleak: take a full lowmem check in
kmemleak_*_phys()") brought false leak alarms on some archs like arm64
that does not init pfn boundary in early booting. The final solution
lands on linux-6.0: commit 0c24e06119 ("mm: kmemleak: add rbtree and
store physical address for objects allocated with PA").
Revert this commit before linux-6.0. The original issue of invalid PA
can be mitigated by additional check in devicetree.
The false alarm report is as following: Kmemleak output: (Qemu/arm64)
unreferenced object 0xffff0000c0170a00 (size 128):
comm "swapper/0", pid 1, jiffies 4294892404 (age 126.208s)
hex dump (first 32 bytes):
62 61 73 65 00 00 00 00 00 00 00 00 00 00 00 00 base............
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<(____ptrval____)>] __kmalloc_track_caller+0x1b0/0x2e4
[<(____ptrval____)>] kstrdup_const+0x8c/0xc4
[<(____ptrval____)>] kvasprintf_const+0xbc/0xec
[<(____ptrval____)>] kobject_set_name_vargs+0x58/0xe4
[<(____ptrval____)>] kobject_add+0x84/0x100
[<(____ptrval____)>] __of_attach_node_sysfs+0x78/0xec
[<(____ptrval____)>] of_core_init+0x68/0x104
[<(____ptrval____)>] driver_init+0x28/0x48
[<(____ptrval____)>] do_basic_setup+0x14/0x28
[<(____ptrval____)>] kernel_init_freeable+0x110/0x178
[<(____ptrval____)>] kernel_init+0x20/0x1a0
[<(____ptrval____)>] ret_from_fork+0x10/0x20
This pacth is also applicable to linux-5.17.y/linux-5.18.y/linux-5.19.y
Cc: <stable@vger.kernel.org>
Signed-off-by: Yee Lee <yee.lee@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9a472613f5 upstream.
The soc/fsl/dpio driver will perform a soc_device_match()
to determine the optimal cache settings for a given CPU core.
If FSL_GUTS is not enabled, this search will fail and
the driver will not configure cache stashing for the given
DPIO, and a string of "unknown SoC" messages will appear:
fsl_mc_dpio dpio.7: unknown SoC version
fsl_mc_dpio dpio.6: unknown SoC version
fsl_mc_dpio dpio.5: unknown SoC version
Fixes: 51da14e96e ("soc: fsl: dpio: configure cache stashing destination")
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220901052149.23873-2-matt@traverse.com.au'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2f79cdfe58 upstream.
Commit d4252071b9 ("add barriers to buffer_uptodate and
set_buffer_uptodate") added proper memory barriers to the buffer head
BH_Uptodate bit, so that anybody who tests a buffer for being up-to-date
will be guaranteed to actually see initialized state.
However, that commit didn't _just_ add the memory barrier, it also ended
up dropping the "was it already set" logic that the BUFFER_FNS() macro
had.
That's conceptually the right thing for a generic "this is a memory
barrier" operation, but in the case of the buffer contents, we really
only care about the memory barrier for the _first_ time we set the bit,
in that the only memory ordering protection we need is to avoid anybody
seeing uninitialized memory contents.
Any other access ordering wouldn't be about the BH_Uptodate bit anyway,
and would require some other proper lock (typically BH_Lock or the folio
lock). A reader that races with somebody invalidating the buffer head
isn't an issue wrt the memory ordering, it's a serialization issue.
Now, you'd think that the buffer head operations don't matter in this
day and age (and I certainly thought so), but apparently some loads
still end up being heavy users of buffer heads. In particular, the
kernel test robot reported that not having this bit access optimization
in place caused a noticeable direct IO performance regression on ext4:
fxmark.ssd_ext4_no_jnl_DWTL_54_directio.works/sec -26.5% regression
although you presumably need a fast disk and a lot of cores to actually
notice.
Link: https://lore.kernel.org/all/Yw8L7HTZ%2FdE2%2Fo9C@xsang-OptiPlex-9020/
Reported-by: kernel test robot <oliver.sang@intel.com>
Tested-by: Fengwei Yin <fengwei.yin@intel.com>
Cc: Mikulas Patocka <mpatocka@redhat.com>
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6d0ef72415 upstream.
This reverts commit a8eb8e6f71 as
it can cause invalid link quality command sent to the firmware
and address the off-by-one issue by fixing condition of while loop.
Cc: stable@vger.kernel.org
Fixes: a8eb8e6f71 ("wifi: iwlegacy: 4965: fix potential off-by-one overflow in il4965_rs_fill_link_cmd()")
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220815073737.GA999388@wp.pl
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fa3fbe6403 upstream.
In case of drv own fail in reset, we may need to run mac_reset several
times. The sequence would trigger system crash as the log below.
Because we do not re-enable/schedule "tx_napi" before disable it again,
the process would keep waiting for state change in napi_diable(). To
avoid the problem and keep status synchronize for each run, goto final
resource handling if drv own failed.
[ 5857.353423] mt7921e 0000:3b:00.0: driver own failed
[ 5858.433427] mt7921e 0000:3b:00.0: Timeout for driver own
[ 5859.633430] mt7921e 0000:3b:00.0: driver own failed
[ 5859.633444] ------------[ cut here ]------------
[ 5859.633446] WARNING: CPU: 6 at kernel/kthread.c:659 kthread_park+0x11d
[ 5859.633717] Workqueue: mt76 mt7921_mac_reset_work [mt7921_common]
[ 5859.633728] RIP: 0010:kthread_park+0x11d/0x150
[ 5859.633736] RSP: 0018:ffff8881b676fc68 EFLAGS: 00010202
......
[ 5859.633766] Call Trace:
[ 5859.633768] <TASK>
[ 5859.633771] mt7921e_mac_reset+0x176/0x6f0 [mt7921e]
[ 5859.633778] mt7921_mac_reset_work+0x184/0x3a0 [mt7921_common]
[ 5859.633785] ? mt7921_mac_set_timing+0x520/0x520 [mt7921_common]
[ 5859.633794] ? __kasan_check_read+0x11/0x20
[ 5859.633802] process_one_work+0x7ee/0x1320
[ 5859.633810] worker_thread+0x53c/0x1240
[ 5859.633818] kthread+0x2b8/0x370
[ 5859.633824] ? process_one_work+0x1320/0x1320
[ 5859.633828] ? kthread_complete_and_exit+0x30/0x30
[ 5859.633834] ret_from_fork+0x1f/0x30
[ 5859.633842] </TASK>
Cc: stable@vger.kernel.org
Fixes: 0efaf31dec ("mt76: mt7921: fix MT7921E reset failure")
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Link: https://lore.kernel.org/r/727eb5ffd3c7c805245e512da150ecf0a7154020.1659452909.git.deren.wu@mediatek.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9cb636b5f6 upstream.
A race condition may occur if the user calls close() on another thread
during a write() operation on the device node of the efi capsule.
This is a race condition that occurs between the efi_capsule_write() and
efi_capsule_flush() functions of efi_capsule_fops, which ultimately
results in UAF.
So, the page freeing process is modified to be done in
efi_capsule_release() instead of efi_capsule_flush().
Cc: <stable@vger.kernel.org> # v4.9+
Signed-off-by: Hyunwoo Kim <imv4bel@gmail.com>
Link: https://lore.kernel.org/all/20220907102920.GA88602@ubuntu/
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1a3887924a upstream.
The EFI stub is a wrapper around the core kernel that makes it look like
a EFI compatible PE/COFF application to the EFI firmware. EFI
applications run on top of the EFI runtime, which is heavily based on
so-called protocols, which are struct types consisting [mostly] of
function pointer members that are instantiated and recorded in a
protocol database.
These structs look like the ideal randomization candidates to the
randstruct plugin (as they only carry function pointers), but of course,
these protocols are contracts between the firmware that exposes them,
and the EFI applications (including our stubbed kernel) that invoke
them. This means that struct randomization for EFI protocols is not a
great idea, and given that the stub shares very little data with the
core kernel that is represented as a randomizable struct, we're better
off just disabling it completely here.
Cc: <stable@vger.kernel.org> # v4.14+
Reported-by: Daniel Marth <daniel.marth@inso.tuwien.ac.at>
Tested-by: Daniel Marth <daniel.marth@inso.tuwien.ac.at>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c9ab053e56 upstream.
A kick_timer timer_list is replaced with kick_timeout delayed_work to be
able to synchronize with mutexes as a prerequisite for the introduction
of tx_mutex.
Found by Linux Verification Center (linuxtesting.org) with Syzkaller.
Fixes: c568f7086c ("tty: n_gsm: fix missing timer to handle stalled links")
Cc: stable <stable@kernel.org>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Suggested-by: Hillf Danton <hdanton@sina.com>
Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru>
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Link: https://lore.kernel.org/r/20220829131640.69254-2-pchelkin@ispras.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4bb1a53be8 upstream.
syzbot is reporting use of uninitialized spinlock at gsmld_write() [1], for
commit 32dd59f969 ("tty: n_gsm: fix race condition in gsmld_write()")
allows accessing gsm->tx_lock before gsm_activate_mux() initializes it.
Since object initialization should be done right after allocation in order
to avoid accessing uninitialized memory, move initialization of
timer/work/waitqueue/spinlock from gsmld_open()/gsm_activate_mux() to
gsm_alloc_mux().
Link: https://syzkaller.appspot.com/bug?extid=cf155def4e717db68a12 [1]
Fixes: 32dd59f969 ("tty: n_gsm: fix race condition in gsmld_write()")
Reported-by: syzbot <syzbot+cf155def4e717db68a12@syzkaller.appspotmail.com>
Tested-by: syzbot <syzbot+cf155def4e717db68a12@syzkaller.appspotmail.com>
Cc: stable <stable@kernel.org>
Acked-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Link: https://lore.kernel.org/r/2110618e-57f0-c1ce-b2ad-b6cacef3f60e@I-love.SAKURA.ne.jp
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f16c6d2e58 upstream.
A null pointer dereference can happen when attempting to access the
"gsm->receive()" function in gsmld_receive_buf(). Currently, the code
assumes that gsm->recieve is only called after MUX activation.
Since the gsmld_receive_buf() function can be accessed without the need to
initialize the MUX, the gsm->receive() function will not be set and a
NULL pointer dereference will occur.
Fix this by avoiding the call to "gsm->receive()" in case the function is
not initialized by adding a sanity check.
Call Trace:
<TASK>
gsmld_receive_buf+0x1c2/0x2f0 drivers/tty/n_gsm.c:2861
tiocsti drivers/tty/tty_io.c:2293 [inline]
tty_ioctl+0xa75/0x15d0 drivers/tty/tty_io.c:2692
vfs_ioctl fs/ioctl.c:51 [inline]
__do_sys_ioctl fs/ioctl.c:870 [inline]
__se_sys_ioctl fs/ioctl.c:856 [inline]
__x64_sys_ioctl+0x193/0x200 fs/ioctl.c:856
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x35/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
Link: https://syzkaller.appspot.com/bug?id=bdf035c61447f8c6e0e6920315d577cb5cc35ac5
Fixes: 01aecd9171 ("tty: n_gsm: fix tty registration before control channel open")
Cc: stable <stable@kernel.org>
Reported-and-tested-by: syzbot+e3563f0c94e188366dbb@syzkaller.appspotmail.com
Signed-off-by: Mazin Al Haddad <mazinalhaddad05@gmail.com>
Link: https://lore.kernel.org/r/20220814015211.84180-1-mazinalhaddad05@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0211c2a0ea upstream.
The stuff programmed into the wm/ddb registers of planes
on disabled pipes doesn't matter. So during readout just
leave our software state tracking for those zeroed.
This should avoid us trying too hard to clean up after
whatever mess the VBIOS/GOP left in there. The actual
hardware state will get cleaned up if/when we enable
the pipe anyway.
Cc: stable@vger.kernel.org
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/5711
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220617195948.24007-1-ville.syrjala@linux.intel.com
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
(cherry picked from commit b183db8f47)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 919bef7a10 upstream.
The quirk added in upstream commit 90c3e21987 ("drm/i915/glk: Add
Quirk for GLK NUC HDMI port issues.") is also required on the ECS Liva
Q2.
Note: Would be nicer to figure out the extra delay required for the
retimer without quirks, however don't know how to check for that.
Cc: stable@vger.kernel.org
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/1326
Signed-off-by: Diego Santa Cruz <Diego.SantaCruz@spinetix.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220616124137.3184371-1-jani.nikula@intel.com
(cherry picked from commit 08e9505fa8)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4595a25443 upstream.
If the GuC CTs are full and we need to stall the request submission
while waiting for space, we save the stalled request and where the stall
occurred; when the CTs have space again we pick up the request submission
from where we left off.
If a full GT reset occurs, the state of all contexts is cleared and all
non-guilty requests are unsubmitted, therefore we need to restart the
stalled request submission from scratch. To make sure that we do so,
clear the saved request after a reset.
Fixes note: the patch that introduced the bug is in 5.15, but no
officially supported platform had GuC submission enabled by default
in that kernel, so the backport to that particular version (and only
that one) can potentially be skipped.
Fixes: 925dc1cf58 ("drm/i915/guc: Implement GuC submission tasklet")
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Matthew Brost <matthew.brost@intel.com>
Cc: John Harrison <john.c.harrison@intel.com>
Cc: <stable@vger.kernel.org> # v5.15+
Reviewed-by: John Harrison <John.C.Harrison@Intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220811210812.3239621-1-daniele.ceraolospurio@intel.com
(cherry picked from commit f922fbb0f2)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3e7e04b747 upstream.
It's been reported that there is a possible data-race accessing to the
global card_requested[] array at ALSA sequencer core, which is used
for determining whether to call request_module() for the card or not.
This data race itself is almost harmless, as it might end up with one
extra request_module() call for the already loaded module at most.
But it's still better to fix.
This patch addresses the possible data race of card_requested[] and
client_requested[] arrays by replacing them with bitmask.
It's an atomic operation and can work without locks.
Reported-by: Abhishek Shah <abhishek.shah@columbia.edu>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/CAEHB24_ay6YzARpA1zgCsE7=H9CSJJzux618E=Ka4h0YdKn=qA@mail.gmail.com
Link: https://lore.kernel.org/r/20220823072717.1706-2-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 22dec134db upstream.
ALSA OSS sequencer refers to a global variable max_midi_devs at
creating a new port, storing it to its own field. Meanwhile this
variable may be changed by other sequencer events at
snd_seq_oss_midi_check_exit_port() in parallel, which may cause a data
race.
OTOH, this data race itself is almost harmless, as the access to the
MIDI device is done via get_mdev() and it's protected with a refcount,
hence its presence is guaranteed.
Though, it's sill better to address the data-race from the code sanity
POV, and this patch adds the proper spinlock for the protection.
Reported-by: Abhishek Shah <abhishek.shah@columbia.edu>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/CAEHB2493pZRXs863w58QWnUTtv3HHfg85aYhLn5HJHCwxqtHQg@mail.gmail.com
Link: https://lore.kernel.org/r/20220823072717.1706-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a8d302a0b7 upstream.
We dropped the x86-specific hack for WC-page allocations with a hope
that the standard dma_alloc_wc() works nowadays. Alas, it doesn't,
and we need to take back some workaround again, but in a different
form, as the previous one was broken for some platforms.
This patch re-introduces the x86-specific WC-page allocations, but it
uses rather the manual page allocations instead of
dma_alloc_coherent(). The use of dma_alloc_coherent() was also a
potential problem in the recent addition of the fallback allocation
for noncontig pages, and this patch eliminates both at once.
Fixes: 9882d63bea ("ALSA: memalloc: Drop x86-specific hack for WC allocations")
Cc: <stable@vger.kernel.org>
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=216363
Link: https://lore.kernel.org/r/20220821155911.10715-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f0da47118c upstream.
Upon reception, a packet must be categorized, either it's destination is
the host, or it is another host. A packet with no destination addressing
fields may be valid in two situations:
- the packet has no source field: only ACKs are built like that, we
consider the host as the destination.
- the packet has a valid source field: it is directed to the PAN
coordinator, as for know we don't have this information we consider we
are not the PAN coordinator.
There was likely a copy/paste error made during a previous cleanup
because the if clause is now containing exactly the same condition as in
the switch case, which can never be true. In the past the destination
address was used in the switch and the source address was used in the
if, which matches what the spec says.
Cc: stable@vger.kernel.org
Fixes: ae531b9475 ("ieee802154: use ieee802154_addr instead of *_sa variants")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20220826142954.254853-1-miquel.raynal@bootlin.com
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 278d3ba615 upstream.
On 32bit-UP u64_stats_fetch_begin() disables only preemption. If the
reader is in preemptible context and the writer side
(u64_stats_update_begin*()) runs in an interrupt context (IRQ or
softirq) then the writer can update the stats during the read operation.
This update remains undetected.
Use u64_stats_fetch_begin_irq() to ensure the stats fetch on 32bit-UP
are not interrupted by a writer. 32bit-SMP remains unaffected by this
change.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Catherine Sullivan <csully@google.com>
Cc: David Awogbemila <awogbemila@google.com>
Cc: Dimitris Michailidis <dmichail@fungible.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Jeroen de Borst <jeroendb@google.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Simon Horman <simon.horman@corigine.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: oss-drivers@corigine.com
Cc: stable@vger.kernel.org
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit eb55dc09b5 upstream.
__mkroute_input() uses fib_validate_source() to trigger an icmp redirect.
My understanding is that fib_validate_source() is used to know if the src
address and the gateway address are on the same link. For that,
fib_validate_source() returns 1 (same link) or 0 (not the same network).
__mkroute_input() is the only user of these positive values, all other
callers only look if the returned value is negative.
Since the below patch, fib_validate_source() didn't return anymore 1 when
both addresses are on the same network, because the route lookup returns
RT_SCOPE_LINK instead of RT_SCOPE_HOST. But this is, in fact, right.
Let's adapat the test to return 1 again when both addresses are on the same
link.
CC: stable@vger.kernel.org
Fixes: 747c143072 ("ip: fix dflt addr selection for connected nexthop")
Reported-by: kernel test robot <yujie.liu@intel.com>
Reported-by: Heng Qi <hengqi@linux.alibaba.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20220829100121.3821-1-nicolas.dichtel@6wind.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 60deb9f10e upstream.
ieee80211_scan_rx() tries to access scan_req->flags after a
null check, but a UAF is observed when the scan is completed
and __ieee80211_scan_completed() executes, which then calls
cfg80211_scan_done() leading to the freeing of scan_req.
Since scan_req is rcu_dereference()'d, prevent the racing in
__ieee80211_scan_completed() by ensuring that from mac80211's
POV it is no longer accessed from an RCU read critical section
before we call cfg80211_scan_done().
Cc: stable@vger.kernel.org
Link: https://syzkaller.appspot.com/bug?extid=f9acff9bf08a845f225d
Reported-by: syzbot+f9acff9bf08a845f225d@syzkaller.appspotmail.com
Suggested-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Siddh Raman Pant <code@siddh.me>
Link: https://lore.kernel.org/r/20220819200340.34826-1-code@siddh.me
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 25e9fbf0fd upstream.
Both __device_attach_driver() and __driver_attach() check the return
code of the bus_type.match() function to see if the device needs to be
added to the deferred probe list. After adding the device to the list,
the logic attempts to bind the device to the driver anyway, as if the
device had matched with the driver, which is not correct.
If __device_attach_driver() detects that the device in question is not
ready to match with a driver on the bus, then it doesn't make sense for
the device to attempt to bind with the current driver or continue
attempting to match with any of the other drivers on the bus. So, update
the logic in __device_attach_driver() to reflect this.
If __driver_attach() detects that a driver tried to match with a device
that is not ready to match yet, then the driver should not attempt to bind
with the device. However, the driver can still attempt to match and bind
with other devices on the bus, as drivers can be bound to multiple
devices. So, update the logic in __driver_attach() to reflect this.
Fixes: 656b8035b0 ("ARM: 8524/1: driver cohandle -EPROBE_DEFER from bus_type.match()")
Cc: stable@vger.kernel.org
Cc: Saravana Kannan <saravanak@google.com>
Reported-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Saravana Kannan <saravanak@google.com>
Signed-off-by: Isaac J. Manjarres <isaacmanjarres@google.com>
Link: https://lore.kernel.org/r/20220817184026.3468620-1-isaacmanjarres@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4831be702b upstream.
Like crashk_res, Calling crash_exclude_mem_range function with
crashk_low_res area would need extra crash_mem range too.
Add one more extra cmem slot in case of crashk_low_res is used.
Signed-off-by: Levi Yun <ppbuk5246@gmail.com>
Fixes: 944a45abfa ("arm64: kdump: Reimplement crashkernel=X")
Cc: <stable@vger.kernel.org> # 5.19.x
Acked-by: Baoquan He <bhe@redhat.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Link: https://lore.kernel.org/r/20220831103913.12661-1-ppbuk5246@gmail.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a3f7c10a26 upstream.
Previously when we added a fence to a dma_resv object we always
assumed the the newer than all the existing fences.
With Jason's work to add an UAPI to explicit export/import that's not
necessary the case any more. So without this check we would allow
userspace to force the kernel into an use after free error.
Since the change is very small and defensive it's probably a good
idea to backport this to stable kernels as well just in case others
are using the dma_resv object in the same way.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Jason Ekstrand <jason.ekstrand@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220810172617.140047-1-christian.koenig@amd.com
Cc: stable@vger.kernel.org # v5.19+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1016fc0c09 upstream.
A recent commit expanding the scope of the udc_lock mutex in the
gadget core managed to cause an obscure and slightly bizarre lockdep
violation. In abbreviated form:
======================================================
WARNING: possible circular locking dependency detected
5.19.0-rc7+ #12510 Not tainted
------------------------------------------------------
udevadm/312 is trying to acquire lock:
ffff80000aae1058 (udc_lock){+.+.}-{3:3}, at: usb_udc_uevent+0x54/0xe0
but task is already holding lock:
ffff000002277548 (kn->active#4){++++}-{0:0}, at: kernfs_seq_start+0x34/0xe0
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #3 (kn->active#4){++++}-{0:0}:
lock_acquire+0x68/0x84
__kernfs_remove+0x268/0x380
kernfs_remove_by_name_ns+0x58/0xac
sysfs_remove_file_ns+0x18/0x24
device_del+0x15c/0x440
-> #2 (device_links_lock){+.+.}-{3:3}:
lock_acquire+0x68/0x84
__mutex_lock+0x9c/0x430
mutex_lock_nested+0x38/0x64
device_link_remove+0x3c/0xa0
_regulator_put.part.0+0x168/0x190
regulator_put+0x3c/0x54
devm_regulator_release+0x14/0x20
-> #1 (regulator_list_mutex){+.+.}-{3:3}:
lock_acquire+0x68/0x84
__mutex_lock+0x9c/0x430
mutex_lock_nested+0x38/0x64
regulator_lock_dependent+0x54/0x284
regulator_enable+0x34/0x80
phy_power_on+0x24/0x130
__dwc2_lowlevel_hw_enable+0x100/0x130
dwc2_lowlevel_hw_enable+0x18/0x40
dwc2_hsotg_udc_start+0x6c/0x2f0
gadget_bind_driver+0x124/0x1f4
-> #0 (udc_lock){+.+.}-{3:3}:
__lock_acquire+0x1298/0x20cc
lock_acquire.part.0+0xe0/0x230
lock_acquire+0x68/0x84
__mutex_lock+0x9c/0x430
mutex_lock_nested+0x38/0x64
usb_udc_uevent+0x54/0xe0
Evidently this was caused by the scope of udc_mutex being too large.
The mutex is only meant to protect udc->driver along with a few other
things. As far as I can tell, there's no reason for the mutex to be
held while the gadget core calls a gadget driver's ->bind or ->unbind
routine, or while a UDC is being started or stopped. (This accounts
for link #1 in the chain above, where the mutex is held while the
dwc2_hsotg_udc is started as part of driver probing.)
Gadget drivers' ->disconnect callbacks are problematic. Even though
usb_gadget_disconnect() will now acquire the udc_mutex, there's a
window in usb_gadget_bind_driver() between the times when the mutex is
released and the ->bind callback is invoked. If a disconnect occurred
during that window, we could call the driver's ->disconnect routine
before its ->bind routine. To prevent this from happening, it will be
necessary to prevent a UDC from connecting while it has no gadget
driver. This should be done already but it doesn't seem to be;
currently usb_gadget_connect() has no check for this. Such a check
will have to be added later.
Some degree of mutual exclusion is required in soft_connect_store(),
which can dereference udc->driver at arbitrary times since it is a
sysfs callback. The solution here is to acquire the gadget's device
lock rather than the udc_mutex. Since the driver core guarantees that
the device lock is always held during driver binding and unbinding,
this will make the accesses in soft_connect_store() mutually exclusive
with any changes to udc->driver.
Lastly, it turns out there is one place which should hold the
udc_mutex but currently does not: The function_show() routine needs
protection while it dereferences udc->driver. The missing lock and
unlock calls are added.
Link: https://lore.kernel.org/all/b2ba4245-9917-e399-94c8-03a383e7070e@samsung.com/
Fixes: 2191c00855 ("USB: gadget: Fix use-after-free Read in usb_udc_uevent()")
Cc: Felipe Balbi <balbi@kernel.org>
Cc: stable@vger.kernel.org
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/YwkfhdxA/I2nOcK7@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9d4dc16ec7 upstream.
During cdrom emulation, the response to read_toc command must contain
the cdrom address as the number of sectors (2048 byte sized blocks)
represented either as an absolute value (when MSF bit is '0') or in
terms of PMin/PSec/PFrame (when MSF bit is set to '1'). Incase of
cdrom, the fsg_lun_open call sets the sector size to 2048 bytes.
When MAC OS sends a read_toc request with MSF set to '1', the
store_cdrom_address assumes that the address being provided is the
LUN size represented in 512 byte sized blocks instead of 2048. It
tries to modify the address further to convert it to 2048 byte sized
blocks and store it in MSF format. This results in data transfer
failures as the cdrom address being provided in the read_toc response
is incorrect.
Fixes: 3f565a363c ("usb: gadget: storage: adapt logic block size to bound block devices")
Cc: stable@vger.kernel.org
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Link: https://lore.kernel.org/r/1661570110-19127-1-git-send-email-quic_kriskura@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f511aef2eb upstream.
On page 362 of the USB3.2 specification (
https://usb.org/sites/default/files/usb_32_20210125.zip),
The 'SuperSpeed Endpoint Companion Descriptor' shall only be returned
by Enhanced SuperSpeed devices that are operating at Gen X speed.
Each endpoint described in an interface is followed by a 'SuperSpeed
Endpoint Companion Descriptor'.
If users use SuperSpeed UDC, host can't recognize the device if endpoint
doesn't have 'SuperSpeed Endpoint Companion Descriptor' followed.
Currently in the uac2 driver code:
1. ss_epout_desc_comp follows ss_epout_desc;
2. ss_epin_fback_desc_comp follows ss_epin_fback_desc;
3. ss_epin_desc_comp follows ss_epin_desc;
4. Only ss_ep_int_desc endpoint doesn't have 'SuperSpeed Endpoint
Companion Descriptor' followed, so we should add it.
Fixes: eaf6cbe099 ("usb: gadget: f_uac2: add volume and mute support")
Cc: stable <stable@kernel.org>
Signed-off-by: Jing Leng <jleng@ambarella.com>
Signed-off-by: Jack Pham <quic_jackp@quicinc.com>
Link: https://lore.kernel.org/r/20220721014815.14453-1-quic_jackp@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6020f48000 upstream.
This happens when @udev->reset_resume is set to true, when usb resume,
the flow as below:
- hub_resume
- usb_disable_interface
- usb_disable_endpoint
- usb_hcd_disable_endpoint
- xhci_endpoint_disable // it set @ep->hcpriv to NULL
Then when reset usb device, it will drop allocated endpoints,
the flow as below:
- usb_reset_and_verify_device
- usb_hcd_alloc_bandwidth
- xhci_mtk_drop_ep
but @ep->hcpriv is already set to NULL, the bandwidth will be not
released anymore.
Due to the added endponts are stored in hash table, we can drop the check
of @ep->hcpriv.
Fixes: 4ce186665e ("usb: xhci-mtk: Do not use xhci's virt_dev in drop_endpoint")
Cc: stable <stable@kernel.org>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/20220819080556.32215-2-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8b13ea0511 upstream.
Currently uses the worst case byte budgets on FS/LS bus bandwidth,
for example, for an isochronos IN endpoint with 192 bytes budget, it
will consume the whole 5 uframes(188 * 5) while the actual FS bus
budget should be just 192 bytes. It cause that many usb audio headsets
with 3 interfaces (audio input, audio output, and HID) cannot be
configured.
To improve it, changes to use "approximate" best case budget for FS/LS
bandwidth management. For the same endpoint from the above example,
the approximate best case budget is now reduced to (188 * 2) bytes.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20220819080556.32215-1-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9c6d778800 upstream.
Automatic kernel fuzzing revealed a recursive locking violation in
usb-storage:
============================================
WARNING: possible recursive locking detected
5.18.0 #3 Not tainted
--------------------------------------------
kworker/1:3/1205 is trying to acquire lock:
ffff888018638db8 (&us_interface_key[i]){+.+.}-{3:3}, at:
usb_stor_pre_reset+0x35/0x40 drivers/usb/storage/usb.c:230
but task is already holding lock:
ffff888018638db8 (&us_interface_key[i]){+.+.}-{3:3}, at:
usb_stor_pre_reset+0x35/0x40 drivers/usb/storage/usb.c:230
...
stack backtrace:
CPU: 1 PID: 1205 Comm: kworker/1:3 Not tainted 5.18.0 #3
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS
1.13.0-1ubuntu1.1 04/01/2014
Workqueue: usb_hub_wq hub_event
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0xcd/0x134 lib/dump_stack.c:106
print_deadlock_bug kernel/locking/lockdep.c:2988 [inline]
check_deadlock kernel/locking/lockdep.c:3031 [inline]
validate_chain kernel/locking/lockdep.c:3816 [inline]
__lock_acquire.cold+0x152/0x3ca kernel/locking/lockdep.c:5053
lock_acquire kernel/locking/lockdep.c:5665 [inline]
lock_acquire+0x1ab/0x520 kernel/locking/lockdep.c:5630
__mutex_lock_common kernel/locking/mutex.c:603 [inline]
__mutex_lock+0x14f/0x1610 kernel/locking/mutex.c:747
usb_stor_pre_reset+0x35/0x40 drivers/usb/storage/usb.c:230
usb_reset_device+0x37d/0x9a0 drivers/usb/core/hub.c:6109
r871xu_dev_remove+0x21a/0x270 drivers/staging/rtl8712/usb_intf.c:622
usb_unbind_interface+0x1bd/0x890 drivers/usb/core/driver.c:458
device_remove drivers/base/dd.c:545 [inline]
device_remove+0x11f/0x170 drivers/base/dd.c:537
__device_release_driver drivers/base/dd.c:1222 [inline]
device_release_driver_internal+0x1a7/0x2f0 drivers/base/dd.c:1248
usb_driver_release_interface+0x102/0x180 drivers/usb/core/driver.c:627
usb_forced_unbind_intf+0x4d/0xa0 drivers/usb/core/driver.c:1118
usb_reset_device+0x39b/0x9a0 drivers/usb/core/hub.c:6114
This turned out not to be an error in usb-storage but rather a nested
device reset attempt. That is, as the rtl8712 driver was being
unbound from a composite device in preparation for an unrelated USB
reset (that driver does not have pre_reset or post_reset callbacks),
its ->remove routine called usb_reset_device() -- thus nesting one
reset call within another.
Performing a reset as part of disconnect processing is a questionable
practice at best. However, the bug report points out that the USB
core does not have any protection against nested resets. Adding a
reset_in_progress flag and testing it will prevent such errors in the
future.
Link: https://lore.kernel.org/all/CAB7eexKUpvX-JNiLzhXBDWgfg2T9e9_0Tw4HQ6keN==voRbP0g@mail.gmail.com/
Cc: stable@vger.kernel.org
Reported-and-tested-by: Rondreis <linhaoguo86@gmail.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/YwkflDxvg0KWqyZK@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c9305b6c1f upstream.
Add proper alignment for .nospec_call_table and .nospec_return_table in
vmlinux.
[hca@linux.ibm.com]: The problem with the missing alignment of the nospec
tables exist since a long time, however only since commit e6ed91fd07
("s390/alternatives: remove padding generation code") and with
CONFIG_RELOCATABLE=n the kernel may also crash at boot time.
The above named commit reduced the size of struct alt_instr by one byte,
so its new size is 11 bytes. Therefore depending on the number of cpu
alternatives the size of the __alt_instructions array maybe odd, which
again also causes that the addresses of the nospec tables will be odd.
If the address of __nospec_call_start is odd and the kernel is compiled
With CONFIG_RELOCATABLE=n the compiler may generate code that loads the
address of __nospec_call_start with a 'larl' instruction.
This will generate incorrect code since the 'larl' instruction only works
with even addresses. In result the members of the nospec tables will be
accessed with an off-by-one offset, which subsequently may lead to
addressing exceptions within __nospec_revert().
Fixes: f19fbd5ed6 ("s390: introduce execute-trampolines for branches")
Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
Link: https://lore.kernel.org/r/8719bf1ce4a72ebdeb575200290094e9ce047bcc.1661557333.git.jpoimboe@kernel.org
Cc: <stable@vger.kernel.org> # 4.16
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7c8d42fdf1 upstream.
The alignment check in prepare_hugepage_range() is wrong for 2 GB
hugepages, it only checks for 1 MB hugepage alignment.
This can result in kernel crash in __unmap_hugepage_range() at the
BUG_ON(start & ~huge_page_mask(h)) alignment check, for mappings
created with MAP_FIXED at unaligned address.
Fix this by correctly handling multiple hugepage sizes, similar to the
generic version of prepare_hugepage_range().
Fixes: d08de8e2d8 ("s390/mm: add support for 2GB hugepages")
Cc: <stable@vger.kernel.org> # 4.8+
Acked-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Gerald Schaefer <gerald.schaefer@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
