MD Danish Anwar says:
====================
Introduce ICSSG based ethernet Driver
The Programmable Real-time Unit and Industrial Communication Subsystem
Gigabit (PRU_ICSSG) is a low-latency microcontroller subsystem in the TI
SoCs. This subsystem is provided for the use cases like the implementation
of custom peripheral interfaces, offloading of tasks from the other
processor cores of the SoC, etc.
The subsystem includes many accelerators for data processing like
multiplier and multiplier-accumulator. It also has peripherals like
UART, MII/RGMII, MDIO, etc. Every ICSSG core includes two 32-bit
load/store RISC CPU cores called PRUs.
The above features allow it to be used for implementing custom firmware
based peripherals like ethernet.
This series adds the YAML documentation and the driver with basic EMAC
support for TI AM654 Silicon Rev 2 SoC with the PRU_ICSSG Sub-system.
running dual-EMAC firmware.
This currently supports basic EMAC with 1Gbps and 100Mbps link. 10M and
half-duplex modes are not yet supported because they require the support
of an IEP, which will be added later.
Advanced features like switch-dev and timestamping will be added later.
This is the v13 of the patch series [v1]. This version of the patchset
addresses comments made on v12.
There series doesn't have any dependency.
Changes from v12 to v13 :
*) Rebased the series on latest net-next.
*) Addressed Jakub's comments on ndo_xmit API. Now we will only stop queues
based on occupancy not on dma errors.
*) Removed limiting the number of serviced packets to budget for Tx NAPI.
Now Tx NAPI will keep servicing packets.
*) Removed netif_running() check when packet arrives.
*) Introduced prototypes of APIs in the same patch where these APIs are added.
Dropped __maybe_unused tags as compiler only cares about prototypes
existing, not whether actual callers are in place. Now prototypes of these
APIs are present in the same patch where they are introduced but thes APIs
are called later (in patch 6).
Changes from v11 to v12 :
*) Rebased the series on latest net-next.
*) Addressed Jakub's comments on ndo_xmit API.
*) Added hooks to .get_rmon_stats for the driver. Now tx / rx bucket size
and frame counts per bucket will be fetched by ethtool_rmon_stats instead
of ethtool -S.
*) Added __maybe_unused tags to unused config and classifier APIs in patch
2,3 and 4. These tags are later removed in patch 6.
Changes from v10 to v11 :
*) Rebased the series on latest net-next.
*) Split the ICSSG driver introduction patch into 9 different patches as
asked by Jakub.
*) Introduced new patch(patch 8/10) to dump Standard network interface
staticstics via ndo_get_stats64. Now certain stats that are reported by
ICSSG hardware and are also part of struct rtnl_link_stats64, will be
reported by ndo_get_stats64. While other stats that are not part of the
struct rtnl_link_stats64 will be reported by ethtool -S. These stats
are not duplicated.
Changes from v9 to v10 :
*) Rebased the series on latest net-next.
*) Moved 'ndev prueth->emac[mac] == emac' assignment to the end of function
prueth_netdev_init().
*) In unsupported phy_mode switch case instead of returning -EINVAL, store
the error code in ret and 'goto free'
Changes from v8 to v9 :
*) Rebased the series on latest net-next.
*) Fixed smatch and sparse warnings as pointed by Simon.
*) Fixed leaky ndev in prueth_netdev_init() as asked by Simon.
Changes from v7 to v8 :
*) Rebased the series on 6.5-rc1.
*) Fixed few formattings.
Changes from v6 to v7 :
*) Added RB tag of Rob in patch 1 of this series.
*) Addressed Simon's comment on patch 2 of the series.
*) Rebased patchset on next-20230428 linux-next.
Changes from v5 to v6 :
*) Added RB tag of Andrew Lunn in patch 2 of this series.
*) Addressed Rob's comment on patch 1 of the series.
*) Rebased patchset on next-20230421 linux-next.
Changes from v4 to v5 :
*) Re-arranged properties section in ti,icssg-prueth.yaml file.
*) Added requirement for minimum one ethernet port.
*) Fixed some minor formatting errors as asked by Krzysztof.
*) Dropped SGMII mode from enum mii_mode as SGMII mode is not currently
supported by the driver.
*) Added switch-case block to handle different phy modes by ICSSG driver.
Changes from v3 to v4 :
*) Addressed Krzysztof's comments and fixed dt_binding_check errors in
patch 1/2.
*) Added interrupt-extended property in ethernet-ports properties section.
*) Fixed comments in file icssg_switch_map.h according to the Linux coding
style in patch 2/2. Added Documentation of structures in patch 2/2.
Changes from v2 to v3 :
*) Addressed Rob and Krzysztof's comments on patch 1 of this series.
Fixed indentation. Removed description and pinctrl section from
ti,icssg-prueth.yaml file.
*) Addressed Krzysztof, Paolo, Randy, Andrew and Christophe's comments on
patch 2 of this seires.
*) Fixed blanklines in Kconfig and Makefile. Changed structures to const
as suggested by Krzysztof.
*) Fixed while loop logic in emac_tx_complete_packets() API as suggested
by Paolo. Previously in the loop's last iteration 'budget' was 0 and
napi_consume_skb would wrongly assume the caller is not in NAPI context
Now, budget won't be zero in last iteration of loop.
*) Removed inline functions addr_to_da1() and addr_to_da0() as asked by
Andrew.
*) Added dev_err_probe() instead of dev_err() as suggested by Christophe.
*) In ti,icssg-prueth.yaml file, in the patternProperties section of
ethernet-ports, kept the port name as "port" instead of "ethernet-port"
as all other drivers were using "port". Will change it if is compulsory
to use "ethernet-port".
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add suspend / resume APIs to support power management in ICSSG ethernet
driver.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add icssg_ethtool.c file. This file will be used for dumping statistics
via ethtool for ICSSG ethernet driver.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement .ndo_get_stats64 to dump standard network interface
statistics for ICSSG ethernet driver.
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add icssg_stats.c to help dump, icssg related driver statistics.
ICSSG has hardware registers for providing statistics like total rx bytes,
total tx bytes, etc. These registers are of 32 bits and hence in case of 1G
link, they overflows in around 32 seconds. The behaviour of these registers
is such that they don't roll back to 0 after overflow but rather stay at
UINT_MAX.
These registers support a feature where the value written to them is
subtracted from the register. This feature can be utilized to fix the
overflowing of stats.
This solution uses a Workqueues based solution where a function gets
called before the registers overflow (every 25 seconds in 1G link, 25000
seconds in 100M link), this function saves the register
values in local variables and writes the last read value to the
register. So any update during the read will be taken care of.
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the Ethernet driver for TI AM654 Silicon rev. 2
with the ICSSG PRU Sub-system running dual-EMAC firmware.
The Programmable Real-time Unit and Industrial Communication Subsystem
Gigabit (PRU_ICSSG) is a low-latency microcontroller subsystem in the TI
SoCs. This subsystem is provided for the use cases like implementation of
custom peripheral interfaces, offloading of tasks from the other
processor cores of the SoC, etc.
Every ICSSG core has two Programmable Real-Time Unit(PRUs),
two auxiliary Real-Time Transfer Unit (RT_PRUs), and
two Transmit Real-Time Transfer Units (TX_PRUs). Each one of these runs
its own firmware. Every ICSSG core has two MII ports connect to these
PRUs and also a MDIO port.
The cores can run different firmwares to support different protocols and
features like switch-dev, timestamping, etc.
It uses System DMA to transfer and receive packets and
shared memory register emulation between the firmware and
driver for control and configuration.
This patch adds support for basic EMAC functionality with 1Gbps
and 100Mbps link speed. 10M and half duplex mode are not supported
currently as they require IEP, the support for which will be added later.
Support for switch-dev, timestamp, etc. will be added later
by subsequent patch series.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a YAML binding document for the ICSSG Programmable real time unit
based Ethernet hardware. The ICSSG driver uses the PRU and PRUSS consumer
APIs to interface the PRUs and load/run the firmware for supporting
ethernet functionality.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add icssg_queue.c file. This file introduces macros and APIs related to
ICSSG queues. These will be used by ICSSG Ethernet driver.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add icssg_config.h / .c and icssg_classifier.c files. These are firmware
configuration and classification related files. These will be used by
ICSSG ethernet driver.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add MII helper APIs and MACROs. These APIs and MACROs will be later used
by ICSSG Ethernet driver. Also introduce icssg_prueth.h which has
definition of prueth related structures.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add firmware interface related headers and macros for ICSSG Ethernet
driver. These macros will be later used by the ICSSG ethernet driver.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch to using data from MDSS driver to program the SSPP fetch and UBWC
configuration. As a side-effect, this also swithes the DPU driver from
DPU_HW_UBWC_VER_xx values to the UBWC_x_y enum, which reflects
the hardware register values.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/550054/
Link: https://lore.kernel.org/r/20230728213320.97309-6-dmitry.baryshkov@linaro.org
* fixes
* preparation for mt7925 support
* mt7981 support
-----BEGIN PGP SIGNATURE-----
Comment: GPGTools - http://gpgtools.org
iF0EABECAB0WIQR10Rp9kadxD0kAQu/XfRQdAqdu9QUCZMd5swAKCRDXfRQdAqdu
9T/kAJ4mRIxpO761ZCD2QQri+UU28vVILQCfejcIlzStrXy1O62qCQX4IhWBhTs=
=97Wi
-----END PGP SIGNATURE-----
Merge tag 'mt76-for-kvalo-2023-07-31' of https://github.com/nbd168/wireless
mt76 patches for 6.6
* fixes
* preparation for mt7925 support
* mt7981 support
Declaring the mask of supported interrupts proved to be error-prone. It
is very easy to add a bit with no corresponding backing block or to miss
the INTF TE bit. Replace this with looping over the enabled INTF blocks
to setup the irq mask.
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/549654/
Link: https://lore.kernel.org/r/20230727144543.1483630-4-dmitry.baryshkov@linaro.org
There is no point in having a single enum (and a single array) for both
DPU < 7.0 and DPU >= 7.0 interrupt registers. Instead define a single
enum and two IRQ address arrays.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Fixes: c731461322 ("drm/msm: Add missing struct identifier")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/549653/
Link: https://lore.kernel.org/r/20230727144543.1483630-3-dmitry.baryshkov@linaro.org
There is no need to call the DRM_DEV_ERROR() function directly to print
a custom message when handling an error from platform_get_irq() function
as it is going to display an appropriate error message
in case of a failure.
Signed-off-by: Ruan Jinjie <ruanjinjie@huawei.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/549499/
Link: https://lore.kernel.org/r/20230727112407.2916029-1-ruanjinjie@huawei.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Fixes XAUI/RXAUI lane alignment errors.
Issue causes dropped packets when trying to communicate over
fiber via SERDES lanes of port 9 and 10.
Errata document applies only to 88E6190X and 88E6390X devices.
Requires poking in undocumented registers.
Signed-off-by: Ante Knezic <ante.knezic@helmholz.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add and document the reserved memory region property in the
mdss-common schema.
For now (sdm845-db845c), it points to a framebuffer memory
region reserved by the bootloader for splash screen.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Amit Pundir <amit.pundir@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/549376/
Link: https://lore.kernel.org/r/20230726132719.2117369-1-amit.pundir@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
dev_close() and dev_open() are issued to change the interface state to DOWN
or UP (dev->flags IFF_UP). When the netdev is set DOWN it loses e.g its
Ipv6 addresses and routes. We don't want this in cases of device recovery
(triggered by hardware or software) or when the qeth device is set
offline.
Setting a qeth device offline or online and device recovery actions call
netif_device_detach() and/or netif_device_attach(). That will reset or
set the LOWER_UP indication i.e. change the dev->state Bit
__LINK_STATE_PRESENT. That is enough to e.g. cause bond failovers, and
still preserves the interface settings that are handled by the network
stack.
Don't call dev_open() nor dev_close() from the qeth device driver. Let the
network stack handle this.
Fixes: d4560150cb ("s390/qeth: call dev_close() during recovery")
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Reviewed-by: Wenjia Zhang <wenjia@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ratheesh Kannoth says:
====================
Packet classify by matching against SPI
1. net: flow_dissector: Add IPSEC dissector.
Flow dissector patch reads IPSEC headers (ESP or AH) header
from packet and retrieves the SPI header.
2. tc: flower: support for SPI.
TC control path changes to pass SPI field from userspace to
kernel.
3. tc: flower: Enable offload support IPSEC SPI field.
Next patch enables the HW support for classify offload for ESP/AH.
This patch enables the HW offload control.
4. octeontx2-pf: TC flower offload support for SPI field.
HW offload support for classification in octeontx2 driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver support to offload TC flower rules which matches
against SPI field of IPSEC packets (AH/ESP).
Signed-off-by: Ratheesh Kannoth <rkannoth@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables offload for TC classifier
flower rules which matches against SPI field.
Signed-off-by: Ratheesh Kannoth <rkannoth@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tc flower rules support to classify ESP/AH
packets matching SPI field.
Signed-off-by: Ratheesh Kannoth <rkannoth@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support for dissecting IPSEC field SPI (which is
32bits in size) for ESP and AH packets.
Signed-off-by: Ratheesh Kannoth <rkannoth@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Laszlo Ersek says:
====================
tun/tap: set sk_uid from current_fsuid()
The original patches fixing CVE-2023-1076 are incorrect in my opinion.
This small series fixes them up; see the individual commit messages for
explanation.
I have a very elaborate test procedure demonstrating the problem for
both tun and tap; it involves libvirt, qemu, and "crash". I can share
that procedure if necessary, but it's indeed quite long (I wrote it
originally for our QE team).
The patches in this series are supposed to "re-fix" CVE-2023-1076; given
that said CVE is classified as Low Impact (CVSSv3=5.5), I'm posting this
publicly, and not suggesting any embargo. Red Hat Product Security may
assign a new CVE number later.
I've tested the patches on top of v6.5-rc4, with "crash" built at commit
c74f375e0ef7.
Cc: Eric Dumazet <edumazet@google.com>
Cc: Lorenzo Colitti <lorenzo@google.com>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Pietro Borrello <borrello@diag.uniroma1.it>
Cc: netdev@vger.kernel.org
Cc: stable@vger.kernel.org
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 66b2c338ad initializes the "sk_uid" field in the protocol socket
(struct sock) from the "/dev/tapX" device node's owner UID. Per original
commit 86741ec254 ("net: core: Add a UID field to struct sock.",
2016-11-04), that's wrong: the idea is to cache the UID of the userspace
process that creates the socket. Commit 86741ec254 mentions socket() and
accept(); with "tap", the action that creates the socket is
open("/dev/tapX").
Therefore the device node's owner UID is irrelevant. In most cases,
"/dev/tapX" will be owned by root, so in practice, commit 66b2c338ad has
no observable effect:
- before, "sk_uid" would be zero, due to undefined behavior
(CVE-2023-1076),
- after, "sk_uid" would be zero, due to "/dev/tapX" being owned by root.
What matters is the (fs)UID of the process performing the open(), so cache
that in "sk_uid".
Cc: Eric Dumazet <edumazet@google.com>
Cc: Lorenzo Colitti <lorenzo@google.com>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Pietro Borrello <borrello@diag.uniroma1.it>
Cc: netdev@vger.kernel.org
Cc: stable@vger.kernel.org
Fixes: 66b2c338ad ("tap: tap_open(): correctly initialize socket uid")
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=2173435
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit a096ccca6e initializes the "sk_uid" field in the protocol socket
(struct sock) from the "/dev/net/tun" device node's owner UID. Per
original commit 86741ec254 ("net: core: Add a UID field to struct
sock.", 2016-11-04), that's wrong: the idea is to cache the UID of the
userspace process that creates the socket. Commit 86741ec254 mentions
socket() and accept(); with "tun", the action that creates the socket is
open("/dev/net/tun").
Therefore the device node's owner UID is irrelevant. In most cases,
"/dev/net/tun" will be owned by root, so in practice, commit a096ccca6e
has no observable effect:
- before, "sk_uid" would be zero, due to undefined behavior
(CVE-2023-1076),
- after, "sk_uid" would be zero, due to "/dev/net/tun" being owned by root.
What matters is the (fs)UID of the process performing the open(), so cache
that in "sk_uid".
Cc: Eric Dumazet <edumazet@google.com>
Cc: Lorenzo Colitti <lorenzo@google.com>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Pietro Borrello <borrello@diag.uniroma1.it>
Cc: netdev@vger.kernel.org
Cc: stable@vger.kernel.org
Fixes: a096ccca6e ("tun: tun_chr_open(): correctly initialize socket uid")
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=2173435
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Neil Armstrong says:
====================
net: ethernet: dwmac: oxnas glue removal
With [1] removing MPCore SMP support, this makes the OX820 barely usable,
associated with a clear lack of maintainance, development and migration to
dt-schema it's clear that Linux support for OX810 and OX820 should be removed.
In addition, the OX810 hasn't been booted for years and isn't even present
in an ARM config file.
For the OX820, lack of USB and SATA support makes the platform not usable
in the current Linux support and relies on off-tree drivers hacked from the
vendor (defunct for years) sources.
The last users are in the OpenWRT distribution, and today's removal means
support will still be in stable 6.1 LTS kernel until end of 2026.
If someone wants to take over the development even with lack of SMP, I'll
be happy to hand off maintainance.
It has been a fun time adding support for this architecture, but it's time
to get over!
This patchset only removes net changes, and is derived from:
https://lore.kernel.org/r/20230630-topic-oxnas-upstream-remove-v2-0-fb6ab3dea87c@linaro.org
---
Changes in v3:
- Removed applied changes
- Added Andy's tags
- Reduced for net
- Link to v2: https://lore.kernel.org/r/20230630-topic-oxnas-upstream-remove-v2-0-fb6ab3dea87c@linaro.org
Changes in v2:
- s/maintainance/maintenance/
- added acked/review tags
- dropped already applied patches
- drop RFC
- Link to v1: https://lore.kernel.org/r/20230331-topic-oxnas-upstream-remove-v1-0-5bd58fd1dd1f@linaro.org
====================
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to lack of maintenance and stall of development for a few years now,
and since no new features will ever be added upstream, remove the
OX810 and OX820 dwmac glue.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Daniel Golle <daniel@makrotopia.org>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to lack of maintenance and stall of development for a few years now,
and since no new features will ever be added upstream, remove support
for OX810 and OX820 ethernet.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Daniel Golle <daniel@makrotopia.org>
Acked-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver can be built as a module, however the lack of the
MODULE_DEVICE_TABLE macro prevents it from being automatically probed
from the DT in such case.
Add the missed macro to make sure the module can load automatically.
Fixes: 6810bb3902 ("drm/panel: Add Samsung S6D7AA0 panel controller driver")
Signed-off-by: Nikita Travkin <nikita@trvn.ru>
Acked-by: Artur Weber <aweber.kernel@gmail.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230802-gt5-panel-dtable-v1-1-c0a765c175e2@trvn.ru
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
