commit 4091c8206c upstream.
i_state_flags used on 32-bit archs, need to clear this flag when
alloc inode.
Find this issue when umount ext4, sometimes track the inode as orphan
accidently, cause ext4 mesg dump.
Fixes: acf943e976 ("ext4: fix checks for orphan inodes")
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Reviewed-by: Baokun Li <libaokun1@huawei.com>
Reviewed-by: Zhang Yi <yi.zhang@huawei.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Message-ID: <20251104-ext4-v1-1-73691a0800f9@nxp.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b97cb7d6a0 upstream.
If ext4_get_inode_loc() fails (e.g. if it returns -EFSCORRUPTED),
iloc.bh will remain set to NULL. Since ext4_xattr_inode_dec_ref_all()
lacks error checking, this will lead to a null pointer dereference
in ext4_raw_inode(), called right after ext4_get_inode_loc().
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: c8e008b604 ("ext4: ignore xattrs past end")
Cc: stable@kernel.org
Signed-off-by: Karina Yankevich <k.yankevich@omp.ru>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reviewed-by: Baokun Li <libaokun1@huawei.com>
Message-ID: <20251022093253.3546296-1-k.yankevich@omp.ru>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d3042cbe84 upstream.
The error path of copying the old config used the wrong variable in the
error message:
$ mkdir /tmp/build
$ ./tools/testing/ktest/config-bisect.pl -b /tmp/build config-good /tmp/config-bad
$ chmod 0 /tmp/build
$ ./tools/testing/ktest/config-bisect.pl -b /tmp/build config-good /tmp/config-bad good
cp /tmp/build//.config config-good.tmp ... [0 seconds] FAILED!
Use of uninitialized value $config in concatenation (.) or string at ./tools/testing/ktest/config-bisect.pl line 744.
failed to copy to config-good.tmp
When it should have shown:
failed to copy /tmp/build//.config to config-good.tmp
Cc: stable@vger.kernel.org
Cc: John 'Warthog9' Hawley <warthog9@kernel.org>
Fixes: 0f0db06599 ("ktest: Add standalone config-bisect.pl program")
Link: https://patch.msgid.link/20251203180924.6862bd26@gandalf.local.home
Reported-by: "John W. Krahn" <jwkrahn@shaw.ca>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 801f614ba2 upstream.
Some NTFS volumes failed to mount because sparse data runs were not
handled correctly during runlist unpacking. The code performed arithmetic
on the special SPARSE_LCN64 marker, leading to invalid LCN values and
mount errors.
Add an explicit check for the case described above, marking the run as
sparse without applying arithmetic.
Fixes: 736fc7bf5f ("fs: ntfs3: Fix integer overflow in run_unpack()")
Cc: stable@vger.kernel.org
Signed-off-by: Konstantin Komarov <almaz.alexandrovich@paragon-software.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 82d2048102 upstream.
For years I wondered why the floppy driver does not just work on
sparc64, e.g:
root@SUNW_375_0066:# disktype /dev/fd0
disktype: Can't open /dev/fd0: No such device or address
[ 525.341906] disktype: attempt to access beyond end of device
fd0: rw=0, sector=0, nr_sectors = 16 limit=8
[ 525.341991] floppy: error 10 while reading block 0
Turns out floppy.c __floppy_read_block_0 tries to read one page for
the first test read to determine the disk size and thus fails if that
is greater than 4k. Adjust minimum MAX_DISK_SIZE to PAGE_SIZE to fix
floppy on sparc64 and likely all other PAGE_SIZE != 4KB configs.
Cc: stable@vger.kernel.org
Signed-off-by: René Rebe <rene@exactco.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3179a5f7f8 upstream.
loop devices under heavy stress-ng loop streessor can trigger many
capacity change events in a short time. Each event prints an info
message from set_capacity_and_notify(), flooding the console and
contributing to soft lockups on slow consoles.
Switch the printk in set_capacity_and_notify() to
pr_info_ratelimited() so frequent capacity changes do not spam
the log while still reporting occasional changes.
Cc: stable@vger.kernel.org
Signed-off-by: Li Chen <chenl311@chinatelecom.cn>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2f22115709 upstream.
In the C code, the 'inc' argument to the assembly functions
blake2s_compress_ssse3() and blake2s_compress_avx512() is declared with
type u32, matching blake2s_compress(). The assembly code then reads it
from the 64-bit %rcx. However, the ABI doesn't guarantee zero-extension
to 64 bits, nor do gcc or clang guarantee it. Therefore, fix these
functions to read this argument from the 32-bit %ecx.
In theory, this bug could have caused the wrong 'inc' value to be used,
causing incorrect BLAKE2s hashes. In practice, probably not: I've fixed
essentially this same bug in many other assembly files too, but there's
never been a real report of it having caused a problem. In x86_64, all
writes to 32-bit registers are zero-extended to 64 bits. That results
in zero-extension in nearly all situations. I've only been able to
demonstrate a lack of zero-extension with a somewhat contrived example
involving truncation, e.g. when the C code has a u64 variable holding
0x1234567800000040 and passes it as a u32 expecting it to be truncated
to 0x40 (64). But that's not what the real code does, of course.
Fixes: ed0356eda1 ("crypto: blake2s - x86_64 SIMD implementation")
Cc: stable@vger.kernel.org
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20251102234209.62133-2-ebiggers@kernel.org
Signed-off-by: Eric Biggers <ebiggers@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b1f856b172 upstream.
According to the hardware programming guide, the clock frequency must
remain below 52MHz during the transition to HS400 mode.
However,in the current implementation, the timing is set to HS400 (a
DDR mode) before adjusting the clock. This causes the clock to double
prematurely to 104MHz during the transition phase, violating the
specification and potentially resulting in CRC errors or CMD timeouts.
This change ensures that clock doubling is avoided during intermediate
transitions and is applied only when the card requires a 200MHz clock
for HS400 operation.
Signed-off-by: Sarthak Garg <sarthak.garg@oss.qualcomm.com>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 62cd5d480b upstream.
'tpm2_load_cmd' allocates a tempoary blob indirectly via 'tpm2_key_decode'
but it is not freed in the failure paths. Address this by wrapping the blob
into with a cleanup helper.
Cc: stable@vger.kernel.org # v5.13+
Fixes: f221974525 ("security: keys: trusted: use ASN.1 TPM2 key format for the blobs")
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d8ee3cfdc8 ]
vhost_vsock_get() uses hash_for_each_possible_rcu() to find the
`vhost_vsock` associated with the `guest_cid`. hash_for_each_possible_rcu()
should only be called within an RCU read section, as mentioned in the
following comment in include/linux/rculist.h:
/**
* hlist_for_each_entry_rcu - iterate over rcu list of given type
* @pos: the type * to use as a loop cursor.
* @head: the head for your list.
* @member: the name of the hlist_node within the struct.
* @cond: optional lockdep expression if called from non-RCU protection.
*
* This list-traversal primitive may safely run concurrently with
* the _rcu list-mutation primitives such as hlist_add_head_rcu()
* as long as the traversal is guarded by rcu_read_lock().
*/
Currently, all calls to vhost_vsock_get() are between rcu_read_lock()
and rcu_read_unlock() except for calls in vhost_vsock_set_cid() and
vhost_vsock_reset_orphans(). In both cases, the current code is safe,
but we can make improvements to make it more robust.
About vhost_vsock_set_cid(), when building the kernel with
CONFIG_PROVE_RCU_LIST enabled, we get the following RCU warning when the
user space issues `ioctl(dev, VHOST_VSOCK_SET_GUEST_CID, ...)` :
WARNING: suspicious RCU usage
6.18.0-rc7 #62 Not tainted
-----------------------------
drivers/vhost/vsock.c:74 RCU-list traversed in non-reader section!!
other info that might help us debug this:
rcu_scheduler_active = 2, debug_locks = 1
1 lock held by rpc-libvirtd/3443:
#0: ffffffffc05032a8 (vhost_vsock_mutex){+.+.}-{4:4}, at: vhost_vsock_dev_ioctl+0x2ff/0x530 [vhost_vsock]
stack backtrace:
CPU: 2 UID: 0 PID: 3443 Comm: rpc-libvirtd Not tainted 6.18.0-rc7 #62 PREEMPT(none)
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.17.0-7.fc42 06/10/2025
Call Trace:
<TASK>
dump_stack_lvl+0x75/0xb0
dump_stack+0x14/0x1a
lockdep_rcu_suspicious.cold+0x4e/0x97
vhost_vsock_get+0x8f/0xa0 [vhost_vsock]
vhost_vsock_dev_ioctl+0x307/0x530 [vhost_vsock]
__x64_sys_ioctl+0x4f2/0xa00
x64_sys_call+0xed0/0x1da0
do_syscall_64+0x73/0xfa0
entry_SYSCALL_64_after_hwframe+0x76/0x7e
...
</TASK>
This is not a real problem, because the vhost_vsock_get() caller, i.e.
vhost_vsock_set_cid(), holds the `vhost_vsock_mutex` used by the hash
table writers. Anyway, to prevent that warning, add lockdep_is_held()
condition to hash_for_each_possible_rcu() to verify that either the
caller is in an RCU read section or `vhost_vsock_mutex` is held when
CONFIG_PROVE_RCU_LIST is enabled; and also clarify the comment for
vhost_vsock_get() to better describe the locking requirements and the
scope of the returned pointer validity.
About vhost_vsock_reset_orphans(), currently this function is only
called via vsock_for_each_connected_socket(), which holds the
`vsock_table_lock` spinlock (which is also an RCU read-side critical
section). However, add an explicit RCU read lock there to make the code
more robust and explicit about the RCU requirements, and to prevent
issues if the calling context changes in the future or if
vhost_vsock_reset_orphans() is called from other contexts.
Fixes: 834e772c8d ("vhost/vsock: fix use-after-free in network stack callers")
Cc: stefanha@redhat.com
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20251126133826.142496-1-sgarzare@redhat.com>
Message-ID: <20251126210313.GA499503@fedora>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b169e1733c ]
Dell Pro Rugged 10/12 tablets has a reliable VGBS method.
If VGBS is not called on boot, the on-screen keyboard won't appear if the
device is booted without a keyboard.
Call VGBS on boot on thess devices to get the initial state of
SW_TABLET_MODE in a reliable way.
Signed-off-by: Chia-Lin Kao (AceLan) <acelan.kao@canonical.com>
Reviewed-by: Hans de Goede <johannes.goede@oss.qualcomm.com>
Link: https://patch.msgid.link/20251127070407.656463-1-acelan.kao@canonical.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b71cbcf7d1 ]
nvme_fc_ctrl_put can acquire the rport lock when freeing the
ctrl object:
nvme_fc_ctrl_put
nvme_fc_ctrl_free
spin_lock_irqsave(rport->lock)
Thus we can't hold the rport lock when calling nvme_fc_ctrl_put.
Justin suggested use the safe list iterator variant because
nvme_fc_ctrl_put will also modify the rport->list.
Cc: Justin Tee <justin.tee@broadcom.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Daniel Wagner <wagi@kernel.org>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 29e8a0c587 ]
In sprd_clk_init(), when devm_clk_get() returns -EPROBE_DEFER
for either uart or source clock, we should propagate the
error instead of just warning and continuing with NULL clocks.
Currently the driver only emits a warning when clock acquisition
fails and proceeds with NULL clock pointers. This can lead to
issues later when the clocks are actually needed. More importantly,
when the clock provider is not ready yet and returns -EPROBE_DEFER,
we should return this error to allow deferred probing.
This change adds explicit checks for -EPROBE_DEFER after both:
1. devm_clk_get(uport->dev, uart)
2. devm_clk_get(uport->dev, source)
When -EPROBE_DEFER is encountered, the function now returns
-EPROBE_DEFER to let the driver framework retry probing
later when the clock dependencies are resolved.
Signed-off-by: Wenhua Lin <Wenhua.Lin@unisoc.com>
Link: https://patch.msgid.link/20251022030840.956589-1-Wenhua.Lin@unisoc.com
Reviewed-by: Cixi Geng <cixi.geng@linux.dev>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 955a48a535 ]
The optical drive of EL-R12 has the same vid and pid as INIC-3069,
as follows:
T: Bus=02 Lev=02 Prnt=02 Port=01 Cnt=01 Dev#= 3 Spd=5000 MxCh= 0
D: Ver= 3.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 9 #Cfgs= 1
P: Vendor=13fd ProdID=3940 Rev= 3.10
S: Manufacturer=HL-DT-ST
S: Product= DVD+-RW GT80N
S: SerialNumber=423349524E4E38303338323439202020
C:* #Ifs= 1 Cfg#= 1 Atr=80 MxPwr=144mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=02 Prot=50 Driver=usb-storage
E: Ad=83(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=0a(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
This will result in the optical drive device also adding
the quirks of US_FL_NO_ATA_1X. When performing an erase operation,
it will fail, and the reason for the failure is as follows:
[ 388.967742] sr 5:0:0:0: [sr0] tag#0 Send: scmd 0x00000000d20c33a7
[ 388.967742] sr 5:0:0:0: [sr0] tag#0 CDB: ATA command pass through(12)/Blank a1 11 00 00 00 00 00 00 00 00 00 00
[ 388.967773] sr 5:0:0:0: [sr0] tag#0 Done: SUCCESS Result: hostbyte=DID_TARGET_FAILURE driverbyte=DRIVER_OK cmd_age=0s
[ 388.967773] sr 5:0:0:0: [sr0] tag#0 CDB: ATA command pass through(12)/Blank a1 11 00 00 00 00 00 00 00 00 00 00
[ 388.967803] sr 5:0:0:0: [sr0] tag#0 Sense Key : Illegal Request [current]
[ 388.967803] sr 5:0:0:0: [sr0] tag#0 Add. Sense: Invalid field in cdb
[ 388.967803] sr 5:0:0:0: [sr0] tag#0 scsi host busy 1 failed 0
[ 388.967803] sr 5:0:0:0: Notifying upper driver of completion (result 8100002)
[ 388.967834] sr 5:0:0:0: [sr0] tag#0 0 sectors total, 0 bytes done.
For the EL-R12 standard optical drive, all operational commands
and usage scenarios were tested without adding the IGNORE_RESIDUE quirks,
and no issues were encountered. It can be reasonably concluded
that removing the IGNORE_RESIDUE quirks has no impact.
Signed-off-by: Chen Changcheng <chenchangcheng@kylinos.cn>
Link: https://patch.msgid.link/20251121064020.29332-1-chenchangcheng@kylinos.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 30cd2cb1ab ]
The UCSI spec states that the num_connectors field is 7 bits, and the
8th bit is reserved and should be set to zero.
Some buggy FW has been known to set this bit, and it can lead to a
system not booting.
Flag that the FW is not behaving correctly, and auto-fix the value
so that the system boots correctly.
Found on Lenovo P1 G8 during Linux enablement program. The FW will
be fixed, but seemed worth addressing in case it hit platforms that
aren't officially Linux supported.
Signed-off-by: Mark Pearson <mpearson-lenovo@squebb.ca>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250821185319.2585023-1-mpearson-lenovo@squebb.ca
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 09bf21bf52 ]
Interrupts are disabled before entering usb_hcd_giveback_urb().
A spinlock_t becomes a sleeping lock on PREEMPT_RT, so it cannot be
acquired with disabled interrupts.
Save the interrupt status and restore it after usb_hcd_giveback_urb().
syz reported:
BUG: sleeping function called from invalid context at kernel/locking/spinlock_rt.c:48
Call Trace:
dump_stack_lvl+0x189/0x250 lib/dump_stack.c:120
rt_spin_lock+0xc7/0x2c0 kernel/locking/spinlock_rt.c:57
spin_lock include/linux/spinlock_rt.h:44 [inline]
mon_bus_complete drivers/usb/mon/mon_main.c:134 [inline]
mon_complete+0x5c/0x200 drivers/usb/mon/mon_main.c:147
usbmon_urb_complete include/linux/usb/hcd.h:738 [inline]
__usb_hcd_giveback_urb+0x254/0x5e0 drivers/usb/core/hcd.c:1647
vhci_urb_enqueue+0xb4f/0xe70 drivers/usb/usbip/vhci_hcd.c:818
Reported-by: syzbot+205ef33a3b636b4181fb@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=205ef33a3b636b4181fb
Signed-off-by: Lizhi Xu <lizhi.xu@windriver.com>
Acked-by: Shuah Khan <skhan@linuxfoundation.org>
Link: https://lore.kernel.org/r/20250916014143.1439759-1-lizhi.xu@windriver.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 51fc7b4ce1 ]
The kernel test robot reported that the exFAT remount operation
failed. The reason for the failure was that the process's umask
is different between mount and remount, causing fs_fmask and
fs_dmask are changed.
Potentially, both gid and uid may also be changed. Therefore, when
initializing fs_context for remount, inherit these mount options
from the options used during mount.
Reported-by: kernel test robot <oliver.sang@intel.com>
Closes: https://lore.kernel.org/oe-lkp/202511251637.81670f5c-lkp@intel.com
Signed-off-by: Yuezhang Mo <Yuezhang.Mo@sony.com>
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7aa31ee9ec ]
The VIA watchdog driver uses allocate_resource() to reserve a MMIO
region for the watchdog control register. However, the allocated
resource was not given a name, which causes the kernel resource tree
to contain an entry marked as "<BAD>" under /proc/iomem on x86
platforms.
During boot, this unnamed resource can lead to a critical hang because
subsequent resource lookups and conflict checks fail to handle the
invalid entry properly.
Signed-off-by: Li Qiang <liqiang01@kylinos.cn>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 957aa59749 ]
If a mailbox command completes immediately after
wait_for_completion_timeout() times out, ha->mbx_intr_comp could be left
in an inconsistent state, causing the next mailbox command not to wait
for the hardware. Fix by reinitializing the completion before use.
Signed-off-by: Tony Battersby <tonyb@cybernetics.com>
Link: https://patch.msgid.link/11b6485e-0bfd-4784-8f99-c06a196dad94@cybernetics.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8f58fc64d5 ]
When given the module parameter qlini_mode=exclusive, qla2xxx in
initiator mode is initially unable to successfully send SCSI commands to
devices it finds while scanning, resulting in an escalating series of
resets until an adapter reset clears the issue. Fix by checking the
active mode instead of the module parameter.
Signed-off-by: Tony Battersby <tonyb@cybernetics.com>
Link: https://patch.msgid.link/1715ec14-ba9a-45dc-9cf2-d41aa6b81b5e@cybernetics.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4f6aaade2a ]
When qla2xxx is loaded with qlini_mode=disabled,
ha->flags.disable_msix_handshake is used before it is set, resulting in
the wrong interrupt handler being used on certain HBAs
(qla2xxx_msix_rsp_q_hs() is used when qla2xxx_msix_rsp_q() should be
used). The only difference between these two interrupt handlers is that
the _hs() version writes to a register to clear the "RISC" interrupt,
whereas the other version does not. So this bug results in the RISC
interrupt being cleared when it should not be. This occasionally causes
a different interrupt handler qla24xx_msix_default() for a different
vector to see ((stat & HSRX_RISC_INT) == 0) and ignore its interrupt,
which then causes problems like:
qla2xxx [0000:02:00.0]-d04c:6: MBX Command timeout for cmd 20,
iocontrol=8 jiffies=1090c0300 mb[0-3]=[0x4000 0x0 0x40 0xda] mb7 0x500
host_status 0x40000010 hccr 0x3f00
qla2xxx [0000:02:00.0]-101e:6: Mailbox cmd timeout occurred, cmd=0x20,
mb[0]=0x20. Scheduling ISP abort
(the cmd varies; sometimes it is 0x20, 0x22, 0x54, 0x5a, 0x5d, or 0x6a)
This problem can be reproduced with a 16 or 32 Gbps HBA by loading
qla2xxx with qlini_mode=disabled and running a high IOPS test while
triggering frequent RSCN database change events.
While analyzing the problem I discovered that even with
disable_msix_handshake forced to 0, it is not necessary to clear the
RISC interrupt from qla2xxx_msix_rsp_q_hs() (more below). So just
completely remove qla2xxx_msix_rsp_q_hs() and the logic for selecting
it, which also fixes the bug with qlini_mode=disabled.
The test below describes the justification for not needing
qla2xxx_msix_rsp_q_hs():
Force disable_msix_handshake to 0:
qla24xx_config_rings():
if (0 && (ha->fw_attributes & BIT_6) && (IS_MSIX_NACK_CAPABLE(ha)) &&
(ha->flags.msix_enabled)) {
In qla24xx_msix_rsp_q() and qla2xxx_msix_rsp_q_hs(), check:
(rd_reg_dword(®->host_status) & HSRX_RISC_INT)
Count the number of calls to each function with HSRX_RISC_INT set and
the number with HSRX_RISC_INT not set while performing some I/O.
If qla2xxx_msix_rsp_q_hs() clears the RISC interrupt (original code):
qla24xx_msix_rsp_q: 50% of calls have HSRX_RISC_INT set
qla2xxx_msix_rsp_q_hs: 5% of calls have HSRX_RISC_INT set
(# of qla2xxx_msix_rsp_q_hs interrupts) =
(# of qla24xx_msix_rsp_q interrupts) * 3
If qla2xxx_msix_rsp_q_hs() does not clear the RISC interrupt (patched
code):
qla24xx_msix_rsp_q: 100% of calls have HSRX_RISC_INT set
qla2xxx_msix_rsp_q_hs: 9% of calls have HSRX_RISC_INT set
(# of qla2xxx_msix_rsp_q_hs interrupts) =
(# of qla24xx_msix_rsp_q interrupts) * 3
In the case of the original code, qla24xx_msix_rsp_q() was seeing
HSRX_RISC_INT set only 50% of the time because qla2xxx_msix_rsp_q_hs()
was clearing it when it shouldn't have been. In the patched code,
qla24xx_msix_rsp_q() sees HSRX_RISC_INT set 100% of the time, which
makes sense if that interrupt handler needs to clear the RISC interrupt
(which it does). qla2xxx_msix_rsp_q_hs() sees HSRX_RISC_INT only 9% of
the time, which is just overlap from the other interrupt during the
high IOPS test.
Tested with SCST on:
QLE2742 FW:v9.08.02 (32 Gbps 2-port)
QLE2694L FW:v9.10.11 (16 Gbps 4-port)
QLE2694L FW:v9.08.02 (16 Gbps 4-port)
QLE2672 FW:v8.07.12 (16 Gbps 2-port)
both initiator and target mode
Signed-off-by: Tony Battersby <tonyb@cybernetics.com>
Link: https://patch.msgid.link/56d378eb-14ad-49c7-bae9-c649b6c7691e@cybernetics.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 825ce89a3e ]
The PUT_64[LB]E() macros need to cast the value to unsigned long long
like the GET_64[LB]E() macros. Caused lots of warnings when compiled
on 32-bit, and clobbered addresses (36-bit P4080).
Signed-off-by: Ben Collins <bcollins@kernel.org>
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Madhavan Srinivasan <maddy@linux.ibm.com>
Link: https://patch.msgid.link/2025042122-mustard-wrasse-694572@boujee-and-buff
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f0e6bc0c3e ]
CP110 based platforms rely on the bootloader for pci port
initialization.
TF-A actively prevents non-uboot re-configuration of pci lanes, and many
boards do not have software control over the pci card reset.
If a pci port had link at boot-time and the clock is stopped at a later
point, the link fails and can not be recovered.
PCI controller driver probe - and by extension ownership of a driver for
the pci clocks - may be delayed especially on large modular kernels,
causing the clock core to start disabling unused clocks.
Add the CLK_IGNORE_UNUSED flag to the three pci port's clocks to ensure
they are not stopped before the pci controller driver has taken
ownership and tested for an existing link.
This fixes failed pci link detection when controller driver probes late,
e.g. with arm64 defconfig and CONFIG_PHY_MVEBU_CP110_COMPHY=m.
Closes: https://lore.kernel.org/r/b71596c7-461b-44b6-89ab-3cfbd492639f@solid-run.com
Signed-off-by: Josua Mayer <josua@solid-run.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3f61783920 ]
am33xx.dtsi has the same clock setup as am35xx.dtsi, setting
ti,no-reset-on-init and ti,no-idle on timer1_target and timer2_target,
so AM33 needs the same workaround as AM35 to avoid ti-sysc probe
failing on certain target modules.
Signed-off-by: Matthias Schiffer <matthias.schiffer@tq-group.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Link: https://lore.kernel.org/r/20250825131114.2206804-1-alexander.stein@ew.tq-group.com
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 81fb53feb6 ]
With mailbox channel requested, there is possibility that interrupts may
come in, so need to make sure the workqueue is initialized before
the queue is scheduled by mailbox rx callback.
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6bd30d8fc5 ]
channel_handler() sets intf->channels_ready to true but never
clears it, so __scan_channels() skips any rescan. When the BMC
firmware changes a rescan is required. Allow it by clearing
the flag before starting a new scan.
Signed-off-by: Jinhui Guo <guojinhui.liam@bytedance.com>
Message-ID: <20250930074239.2353-3-guojinhui.liam@bytedance.com>
Signed-off-by: Corey Minyard <corey@minyard.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 936750fdba ]
The race window between __scan_channels() and deliver_response() causes
the parameters of some channels to be set to 0.
1.[CPUA] __scan_channels() issues an IPMI request and waits with
wait_event() until all channels have been scanned.
wait_event() internally calls might_sleep(), which might
yield the CPU. (Moreover, an interrupt can preempt
wait_event() and force the task to yield the CPU.)
2.[CPUB] deliver_response() is invoked when the CPU receives the
IPMI response. After processing a IPMI response,
deliver_response() directly assigns intf->wchannels to
intf->channel_list and sets intf->channels_ready to true.
However, not all channels are actually ready for use.
3.[CPUA] Since intf->channels_ready is already true, wait_event()
never enters __wait_event(). __scan_channels() immediately
clears intf->null_user_handler and exits.
4.[CPUB] Once intf->null_user_handler is set to NULL, deliver_response()
ignores further IPMI responses, leaving the remaining
channels zero-initialized and unusable.
CPUA CPUB
------------------------------- -----------------------------
__scan_channels()
intf->null_user_handler
= channel_handler;
send_channel_info_cmd(intf,
0);
wait_event(intf->waitq,
intf->channels_ready);
do {
might_sleep();
deliver_response()
channel_handler()
intf->channel_list =
intf->wchannels + set;
intf->channels_ready = true;
send_channel_info_cmd(intf,
intf->curr_channel);
if (condition)
break;
__wait_event(wq_head,
condition);
} while(0)
intf->null_user_handler
= NULL;
deliver_response()
if (!msg->user)
if (intf->null_user_handler)
rv = -EINVAL;
return rv;
------------------------------- -----------------------------
Fix the race between __scan_channels() and deliver_response() by
deferring both the assignment intf->channel_list = intf->wchannels
and the flag intf->channels_ready = true until all channels have
been successfully scanned or until the IPMI request has failed.
Signed-off-by: Jinhui Guo <guojinhui.liam@bytedance.com>
Message-ID: <20250930074239.2353-2-guojinhui.liam@bytedance.com>
Signed-off-by: Corey Minyard <corey@minyard.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5526c1c6ba ]
get_meter_levels_from_urb() parses the 64-byte meter packets sent by
the device and fills the per-channel arrays meter_level[],
comp_level[] and master_level[] in struct snd_us16x08_meter_store.
Currently the function derives the channel index directly from the
meter packet (MUB2(meter_urb, s) - 1) and uses it to index those
arrays without validating the range. If the packet contains a
negative or out-of-range channel number, the driver may write past
the end of these arrays.
Introduce a local channel variable and validate it before updating the
arrays. We reject negative indices, limit meter_level[] and
comp_level[] to SND_US16X08_MAX_CHANNELS, and guard master_level[]
updates with ARRAY_SIZE(master_level).
Fixes: d2bb390a20 ("ALSA: usb-audio: Tascam US-16x08 DSP mixer quirk")
Reported-by: DARKNAVY (@DarkNavyOrg) <vr@darknavy.com>
Closes: https://lore.kernel.org/tencent_21C112743C44C1A2517FF219@qq.com
Signed-off-by: Shipei Qu <qu@darknavy.com>
Link: https://patch.msgid.link/20251217024630.59576-1-qu@darknavy.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5032347c04 ]
When pdacf_config() fails, snd_pdacf_probe() returns the error code
directly without freeing the sound card resources allocated by
snd_card_new(), which leads to a memory leak.
Add proper error handling to free the sound card and clear the card
list entry when pdacf_config() fails.
Fixes: 15b99ac172 ("[PATCH] pcmcia: add return value to _config() functions")
Suggested-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Haotian Zhang <vulab@iscas.ac.cn>
Link: https://patch.msgid.link/20251215090433.211-1-vulab@iscas.ac.cn
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2a03b40dea ]
When vxpocket_config() fails, vxpocket_probe() returns the error code
directly without freeing the sound card resources allocated by
snd_card_new(), which leads to a memory leak.
Add proper error handling to free the sound card and clear the
allocation bit when vxpocket_config() fails.
Fixes: 15b99ac172 ("[PATCH] pcmcia: add return value to _config() functions")
Signed-off-by: Haotian Zhang <vulab@iscas.ac.cn>
Link: https://patch.msgid.link/20251215042652.695-1-vulab@iscas.ac.cn
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit d3ecb12e2e upstream.
MMC_SDHCI_ESDHC_IMX requires ARCH_MXC despite also being used on
ARCH_S32, which results in unmet dependencies when compiling strictly
for ARCH_S32. Resolve this by adding ARCH_S32 as an alternative to
ARCH_MXC in the driver's dependencies.
Fixes: 5c4f00627c ("mmc: sdhci-esdhc-imx: add NXP S32G2 support")
Cc: stable@bvger.kernel.org
Signed-off-by: Jared Kangas <jkangas@redhat.com>
Reviewed-by: Haibo Chen <haibo.chen@nxp.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1417927df8 upstream.
Commit fc96ec826b ("spi: fsl-cpm: Use 16 bit mode for large transfers
with even size") failed to make sure that the size is really even
before switching to 16 bit mode. Until recently the problem went
unnoticed because kernfs uses a pre-allocated bounce buffer of size
PAGE_SIZE for reading EEPROM.
But commit 8ad6249c51 ("eeprom: at25: convert to spi-mem API")
introduced an additional dynamically allocated bounce buffer whose size
is exactly the size of the transfer, leading to a buffer overrun in
the fsl-cpm driver when that size is odd.
Add the missing length parity verification and remain in 8 bit mode
when the length is not even.
Fixes: fc96ec826b ("spi: fsl-cpm: Use 16 bit mode for large transfers with even size")
Cc: stable@vger.kernel.org
Closes: https://lore.kernel.org/all/638496dd-ec60-4e53-bad7-eb657f67d580@csgroup.eu/
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Reviewed-by: Sverdlin Alexander <alexander.sverdlin@siemens.com>
Link: https://patch.msgid.link/3c4d81c3923c93f95ec56702a454744a4bad3cfc.1763627618.git.christophe.leroy@csgroup.eu
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6ea3a44cef upstream.
The current implementation overlooks the 'guaranteed_perf'
register in this check.
If the Guaranteed Performance register is located in the PCC
subspace, the function currently attempts to read it without
acquiring the lock and without sending the CMD_READ doorbell
to the firmware. This can result in reading stale data.
Fixes: 29523f0953 ("ACPI / CPPC: Add support for guaranteed performance")
Signed-off-by: Pengjie Zhang <zhangpengjie2@huawei.com>
Cc: 4.20+ <stable@vger.kernel.org> # 4.20+
[ rjw: Subject and changelog edits ]
Link: https://patch.msgid.link/20251210132227.1988380-1-zhangpengjie2@huawei.com
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aed3716db7 upstream.
The device occasionally wakes up from suspend with missing input on the
internal keyboard and the following suspend attempt results in an instant
wake-up. The quirks fix both issues for this device.
Signed-off-by: Christoffer Sandberg <cs@tuxedo.de>
Signed-off-by: Werner Sembach <wse@tuxedocomputers.com>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20251124203336.64072-1-wse@tuxedocomputers.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 248d3a73a0 upstream.
The current validation 'wire_order[i] > ARRAY_SIZE(config_pins)' allows
wire_order[i] to equal ARRAY_SIZE(config_pins), which causes out-of-bounds
access when used as index in 'config_pins[wire_order[i]]'.
Since config_pins has 4 elements (indices 0-3), the valid range for
wire_order should be 0-3. Fix the off-by-one error by using >= instead
of > in the validation check.
Signed-off-by: Junjie Cao <junjie.cao@intel.com>
Link: https://patch.msgid.link/20251114062817.852698-1-junjie.cao@intel.com
Fixes: bb76dc09dd ("input: ti_am33x_tsc: Order of TSC wires, made configurable")
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7953794f74 upstream.
HID_GD_Z is mapped to ABS_Z for stylus and pen in hid-input.c. But HID_GD_Z
should be used to report ABS_DISTANCE for stylus and pen as described at:
Documentation/input/event-codes.rst#n226
* ABS_DISTANCE:
- Used to describe the distance of a tool from an interaction surface. This
event should only be emitted while the tool is hovering, meaning in close
proximity of the device and while the value of the BTN_TOUCH code is 0. If
the input device may be used freely in three dimensions, consider ABS_Z
instead.
- BTN_TOOL_<name> should be set to 1 when the tool comes into detectable
proximity and set to 0 when the tool leaves detectable proximity.
BTN_TOOL_<name> signals the type of tool that is currently detected by the
hardware and is otherwise independent of ABS_DISTANCE and/or BTN_TOUCH.
This patch makes the correct mapping. The ABS_DISTANCE is currently not mapped
by any HID usage in hid-generic driver.
Signed-off-by: Ping Cheng <ping.cheng@wacom.com>
Cc: stable@kernel.org
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6ef935e659 ]
Currently, the VLAN id may be used without validation when
receive a VLAN configuration mailbox from VF. The length of
vlan_del_fail_bmap is BITS_TO_LONGS(VLAN_N_VID). It may cause
out-of-bounds memory access once the VLAN id is bigger than
or equal to VLAN_N_VID.
Therefore, VLAN id needs to be checked to ensure it is within
the range of VLAN_N_VID.
Fixes: fe4144d47e ("net: hns3: sync VLAN filter entries when kill VLAN ID failed")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20251211023737.2327018-4-shaojijie@huawei.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d180c11aa8 ]
Currently, rss_size = num_tqps / tc_num. If tc_num is 1, then num_tqps
equals rss_size. However, if the tc_num is greater than 1, then rss_size
will be less than num_tqps, causing the tqp_index check for subsequent TCs
using rss_size to always fail.
This patch uses the num_tqps to check whether tqp_index is out of range,
instead of rss_size.
Fixes: 326334aad0 ("net: hns3: add a check for tqp_index in hclge_get_ring_chain_from_mbx()")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20251211023737.2327018-3-shaojijie@huawei.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0cc25c6a14 ]
The c language has a set of implicit type conversions, when
two variables perform bitwise or arithmetic operations.
For example, variable A (type u16/u8) -1, its output is int type variable.
u16/u8 will convert to int type implicitly before it does arithmetic
operations. So, change 1 to unsigned type.
Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: d180c11aa8 ("net: hns3: using the num_tqps to check whether tqp_index is out of range when vf get ring info from mbx")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c2a1626974 ]
Currently, hdev->htqp is allocated using hdev->num_tqps, and kinfo->tqp
is allocated using kinfo->num_tqps. However, kinfo->num_tqps is set to
min(new_tqps, hdev->num_tqps); Therefore, kinfo->num_tqps may be smaller
than hdev->num_tqps, which causes some hdev->htqp[i] to remain
uninitialized in hclgevf_knic_setup().
Thus, this patch allocates hdev->htqp and kinfo->tqp using hdev->num_tqps,
ensuring that the lengths of hdev->htqp and kinfo->tqp are consistent
and that all elements are properly initialized.
Fixes: e2cb1dec97 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20251211023737.2327018-2-shaojijie@huawei.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c0289f67f7 ]
The firmware tracer's format string validation and parameter counting
did not properly handle escaped percent signs (%%). This caused
fw_tracer to count more parameters when trace format strings contained
literal percent characters.
To fix it, allow %% to pass string validation and skip %% sequences when
counting parameters since they represent literal percent signs rather
than format specifiers.
Fixes: 70dd6fdb89 ("net/mlx5: FW tracer, parse traces and kernel tracing support")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reported-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Closes: https://lore.kernel.org/netdev/hanz6rzrb2bqbplryjrakvkbmv4y5jlmtthnvi3thg5slqvelp@t3s3erottr6s/
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/1765284977-1363052-5-git-send-email-tariqt@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b35966042d ]
Add validation for format string parameters in the firmware tracer to
prevent potential security vulnerabilities and crashes from malformed
format strings received from firmware.
The firmware tracer receives format strings from the device firmware and
uses them to format trace messages. Without proper validation, bad
firmware could provide format strings with invalid format specifiers
(e.g., %s, %p, %n) that could lead to crashes, or other undefined
behavior.
Add mlx5_tracer_validate_params() to validate that all format specifiers
in trace strings are limited to safe integer/hex formats (%x, %d, %i,
%u, %llx, %lx, etc.). Reject strings containing other format types that
could be used to access arbitrary memory or cause crashes.
Invalid format strings are added to the trace output for visibility with
"BAD_FORMAT: " prefix.
Fixes: 70dd6fdb89 ("net/mlx5: FW tracer, parse traces and kernel tracing support")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Reported-by: Breno Leitao <leitao@debian.org>
Closes: https://lore.kernel.org/netdev/hanz6rzrb2bqbplryjrakvkbmv4y5jlmtthnvi3thg5slqvelp@t3s3erottr6s/
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/1765284977-1363052-4-git-send-email-tariqt@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f713313523 ]
In case FW is publishing a string which isn't found in the driver's
string DBs, keep the string as raw data.
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Stable-dep-of: b35966042d ("net/mlx5: fw_tracer, Validate format string parameters")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7b07be1ff1 ]
The ethtool -S command operates across three ioctl calls:
ETHTOOL_GSSET_INFO for the size, ETHTOOL_GSTRINGS for the names, and
ETHTOOL_GSTATS for the values.
If the number of stats changes between these calls (e.g., due to device
reconfiguration), userspace's buffer allocation will be incorrect,
potentially leading to buffer overflow.
Drivers are generally expected to maintain stable stat counts, but some
drivers (e.g., mlx5, bnx2x, bna, ksz884x) use dynamic counters, making
this scenario possible.
Some drivers try to handle this internally:
- bnad_get_ethtool_stats() returns early in case stats.n_stats is not
equal to the driver's stats count.
- micrel/ksz884x also makes sure not to write anything beyond
stats.n_stats and overflow the buffer.
However, both use stats.n_stats which is already assigned with the value
returned from get_sset_count(), hence won't solve the issue described
here.
Change ethtool_get_strings(), ethtool_get_stats(),
ethtool_get_phy_stats() to not return anything in case of a mismatch
between userspace's size and get_sset_size(), to prevent buffer
overflow.
The returned n_stats value will be equal to zero, to reflect that
nothing has been returned.
This could result in one of two cases when using upstream ethtool,
depending on when the size change is detected:
1. When detected in ethtool_get_strings():
# ethtool -S eth2
no stats available
2. When detected in get stats, all stats will be reported as zero.
Both cases are presumably transient, and a subsequent ethtool call
should succeed.
Other than the overflow avoidance, these two cases are very evident (no
output/cleared stats), which is arguably better than presenting
incorrect/shifted stats.
I also considered returning an error instead of a "silent" response, but
that seems more destructive towards userspace apps.
Notes:
- This patch does not claim to fix the inherent race, it only makes sure
that we do not overflow the userspace buffer, and makes for a more
predictable behavior.
- RTNL lock is held during each ioctl, the race window exists between
the separate ioctl calls when the lock is released.
- Userspace ethtool always fills stats.n_stats, but it is likely that
these stats ioctls are implemented in other userspace applications
which might not fill it. The added code checks that it's not zero,
to prevent any regressions.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Reviewed-by: Dragos Tatulea <dtatulea@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Gal Pressman <gal@nvidia.com>
Link: https://patch.msgid.link/20251208121901.3203692-1-gal@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 201ed315f9 ]
So that it's easier to follow and make sense of the branching and
various conditions.
Stats retrieval has been split into two separate functions
ethtool_get_phy_stats_phydev & ethtool_get_phy_stats_ethtool.
The former attempts to retrieve the stats using phydev & phy_ops, while
the latter uses ethtool_ops.
Actual n_stats validation & array allocation has been moved into a new
ethtool_vzalloc_stats_array helper.
This also fixes a potential NULL dereference of
ops->get_ethtool_phy_stats where it was getting called in an else branch
unconditionally without making sure it was actually present.
Found by Linux Verification Center (linuxtesting.org) with the SVACE
static analysis tool.
Signed-off-by: Daniil Tatianin <d-tatianin@yandex-team.ru>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: 7b07be1ff1 ("ethtool: Avoid overflowing userspace buffer on stats query")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fd4778581d ]
Now that we always early return if we don't have any stats we can remove
these checks as they're no longer necessary.
Signed-off-by: Daniil Tatianin <d-tatianin@yandex-team.ru>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: 7b07be1ff1 ("ethtool: Avoid overflowing userspace buffer on stats query")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ccd21ec5b8 ]
In ethtool_get_phy_stats(), the phydev varaible is set to
dev->phydev but dev->phydev is still used. Replace
dev->phydev uses with phydev.
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: 7b07be1ff1 ("ethtool: Avoid overflowing userspace buffer on stats query")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 885bebac99 ]
Set the error code if "transferred != sizeof(cmd)" instead of
returning success.
Fixes: dbafc28955 ("NFC: pn533: don't send USB data off of the stack")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://patch.msgid.link/aTfIJ9tZPmeUF4W1@stanley.mountain
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
