Some spi device drivers use the same tx_buf and rx_buf repeatly for better
performance such as driver/input/touchsreen/ads7846.c, but spi core grab tx_buf
/rx_buf of transfer and set them as dummy_tx/dummy_rx once they are NULL. Thus,
in the second time the tx_buf/rx_buf will be replaced by dummy_tx/dummy_rx and
the data which produced by the last tx or rx may be wrongly sent to the device
or handled by the upper level protocol. This patch just keep the orignal value
of tx_buf/rx_buf if they are NULL after this transfer processed.
Signed-off-by: Robin Gong <b38343@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Pull last minute thermal-SoC management fixes from Eduardo Valentin:
"Specifics:
- Minor fixes on ST and RCAR thermal drivers.
- Avoid flooding kernel log when driver returns -EAGAIN.
Note: I am sending this pull on Rui's behalf while he fixes issues in
his Linux box"
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal:
drivers: thermal: st: remove several sparse warnings
thermal: constify of_device_id array
thermal: Do not log an error if thermal_zone_get_temp returns -EAGAIN
thermal: rcar: Fix typo in r8a73a4 SoC name
This reverts commit ecc19d1786.
It added a new warning to try to encourage driver writers to set the
device capabities properly, but drivers haven't been updated and in the
meantime it just generaters a scary message that users cannot actually
do anything about.
Warnings like these are appropriate if you actually expect to fix the
code that causes them. They are not appropriate for releases.
Requested-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull dmaengine fix from Vinod Koul:
"I have one more fix to fix the boot warning on cppi driver due to
missing capabilities"
* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
dmaengine: cppi41: add missing bitfields
Add missing directions, residue_granularity,
srd_addr_widths and dst_addr_widths bitfields.
Without those we will see a kernel WARN()
when loading musb on am335x devices.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The code was using an normal completion, but that caused stuck
task errors after a while. Use an interruptible one to avoid that.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
If ipmi_powernv_recv(...) is called without a current message it
prints a warning and returns. However it fails to release the message
lock causing the system to dead lock during any subsequent IPMI
operations.
This error path should never normally be taken unless there are bugs
elsewhere in the system.
Signed-off-by: Alistair Popple <alistair@popple.id.au>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Some BMCs don't let you clear the receive irq bit in the global
enables. This is kind of silly, but they give an error if you
try to clear it. Compensate for this by detecting the situation
and working around it.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Tested-by: Thomas D <whissi@whissi.de>
Reviewed-by: Thomas D <whissi@whissi.de>
This is our remaining set of three fixes for 4.0: two oops fixes(one for cable
pulls triggering oopses and the other be2iscsi specific) and one warn on in
sysfs on multipath devices using enclosures.
Signed-off-by: James Bottomley <JBottomley@Odin.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABAgAGBQJVKFlCAAoJEDeqqVYsXL0MjOsH/j0DIeMOa7p5JdryKZNY+LY4
HHfVgAK4T+bNZQUOCq/Dctn19CltuJGoDGkY2P4m1YG+mz8NLCm2aEAKp9efhho6
6cLv0An/PlQhFuurbzo9BXsEb93ZENf6ng0WJZ3iOyqD9FA9X+0mDAfXDfJ4mwH3
aGa0NE4bbqhNotWjpdFPIDqU2uwk4pV3M/BRx3JmeIIR2BtaWXkKxTq5tmLo9DDN
22Seu/RJqV7O3WdphLLoN+615eCcroOru54DnQtKQ3/pQeC+6gyHcjkq02KjJ9D+
wBNltUrtqzreDrgF2D6uaxT3NkQFFPlkzjD6Ma5tq5637sT9Tch8/UNTMzs5UgU=
=AbF2
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is our remaining set of three fixes for 4.0: two oops fixes(one
for cable pulls triggering oopses and the other be2iscsi specific) and
one warn on in sysfs on multipath devices using enclosures"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
Defer processing of REQ_PREEMPT requests for blocked devices
be2iscsi: Fix kernel panic when device initialization fails
enclosure: fix WARN_ON removing an adapter in multi-path devices
Pull SCSI target fixes from Nicholas Bellinger:
"Just a few small fixes:
Two from Andy, the first addresses a v4.0 target specific regression
to a user visible configfs attribute, and the second adds a set of
missing brackets around IPv6 discovery portal information within
iscsi-target.
And one from Mike that fixes an OOPs regression in traditional
iscsi-target when an iovec allocation fails, that has been present
since v3.10.y code. (CC'd to stable)"
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
iscsi target: fix oops when adding reject pdu
iscsi-target: TargetAddress in SendTargets should bracket ipv6 addresses
target: Allow userspace to write 1 to attrib/emulate_fua_write
This fixes a oops due to a double list add when adding a reject PDU for
iscsit_allocate_iovecs allocation failures. The cmd has already been
added to the conn_cmd_list in iscsit_setup_scsi_cmd, so this has us call
iscsit_reject_cmd.
Note that for ERL0 the reject PDU is not actually sent, so this patch
is not completely tested. Just verified we do not oops. The problem is the
add reject functions return -1 which is returned all the way up to
iscsi_target_rx_thread which for ERL0 will drop the connection.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: <stable@vger.kernel.org> # v3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
In cases of short transfer times the CPU is spending lots of time
in the interrupt handler and scheduler to reschedule the worker thread.
Measurements show that we have times where it takes 29.32us to between
the last clock change and the time that the worker-thread is running again
returning from wait_for_completion_timeout().
During this time the interrupt-handler is running calling complete()
and then also the scheduler is rescheduling the worker thread.
This time can vary depending on how much of the code is still in
CPU-caches, when there is a burst of spi transfers the subsequent delays
are in the order of 25us, so the value of 30us seems reasonable.
With polling the whole transfer of 4 bytes at 10MHz finishes after 6.16us
(CS down to up) with the real transfer (clock running) taking 3.56us.
So the efficiency has much improved and is also freeing CPU cycles,
reducing interrupts and context switches.
Because of the above 30us seems to be a reasonable limit for polling.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Transforms the bcm-2835 native SPI-chip select to their gpio-cs equivalent.
This allows for some support of some optimizations that are not
possible due to HW-gliches on the CS line - especially filling
the FIFO before enabling SPI interrupts (by writing to CS register)
while the transfer is already in progress (See commit: e3a2be3030)
This patch also works arround some issues in bcm2835-pinctrl which does not
set the value when setting the GPIO as output - it just sets up output and
(typically) leaves the GPIO as low. When a fix for this is merged then this
gpio_set_value can get removed from bcm2835_spi_setup.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
- Revert a 3.17 hibernate commit that was supposed to fix an issue
related to e820 reserved regions, but broke resume from hibernation
on Lenovo x230 (Rafael J Wysocki).
- Prevent the ACPI cpuidle driver from overwriting the name and
description of the C0 state set by the core when the list of
C-states changes (Thomas Schlichter).
- Remove the no longer needed state_count field from struct cpuidle_device
which prevents the list of C-states shown by the sysfs interface from
becoming incorrect when the current number of them is different from
the number of C-states on boot (Bartlomiej Zolnierkiewicz).
- The cpufreq core updates the policy object of the only online CPU
during system resume to make it reflect the current hardware state,
but it always assumes that CPU to be CPU0 which need not be the
case, so fix the code to avoid that assumption (Viresh Kumar).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=g0eu
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-4.0-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI fixes from Rafael Wysocki:
"These are stable-candidate fixes of some recently reported issues in
the cpufreq core, cpuidle core, the ACPI cpuidle driver and the
hibernate core.
Specifics:
- Revert a 3.17 hibernate commit that was supposed to fix an issue
related to e820 reserved regions, but broke resume from hibernation
on Lenovo x230 (Rafael J Wysocki).
- Prevent the ACPI cpuidle driver from overwriting the name and
description of the C0 state set by the core when the list of
C-states changes (Thomas Schlichter).
- Remove the no longer needed state_count field from struct
cpuidle_device which prevents the list of C-states shown by the
sysfs interface from becoming incorrect when the current number of
them is different from the number of C-states on boot (Bartlomiej
Zolnierkiewicz).
- The cpufreq core updates the policy object of the only online CPU
during system resume to make it reflect the current hardware state,
but it always assumes that CPU to be CPU0 which need not be the
case, so fix the code to avoid that assumption (Viresh Kumar)"
* tag 'pm+acpi-4.0-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
Revert "PM / hibernate: avoid unsafe pages in e820 reserved regions"
cpuidle: ACPI: do not overwrite name and description of C0
cpuidle: remove state_count field from struct cpuidle_device
cpufreq: Schedule work for the first-online CPU on resume
* pm-sleep:
Revert "PM / hibernate: avoid unsafe pages in e820 reserved regions"
* pm-cpufreq:
cpufreq: Schedule work for the first-online CPU on resume
* pm-cpuidle:
cpuidle: ACPI: do not overwrite name and description of C0
cpuidle: remove state_count field from struct cpuidle_device
Enumeration
- Don't look for ACPI hotplug parameters if ACPI is disabled (Bjorn Helgaas)
Resource management
- Revert "sparc/PCI: Clip bridge windows to fit in upstream windows" (Bjorn Helgaas)
AER
- Avoid info leak in __print_tlp_header() (Rasmus Villemoes)
PCI device hotplug
- Add missing curly braces in cpci_configure_slot() (Dan Carpenter)
ST Microelectronics SPEAr13xx host bridge driver
- Drop __initdata from spear13xx_pcie_driver (Matwey V. Kornilov)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ituX
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.0-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
"Here are some fixes for v4.0. I apologize for how late they are. We
were hoping for some better fixes, but couldn't get them polished in
time. These fix:
- a Xen domU oops with PCI passthrough devices
- a sparc T5 boot failure
- a STM SPEAr13xx crash (use after initdata freed)
- a cpcihp hotplug driver thinko
- an AER thinko that printed stack junk
Details:
Enumeration
- Don't look for ACPI hotplug parameters if ACPI is disabled (Bjorn Helgaas)
Resource management
- Revert "sparc/PCI: Clip bridge windows to fit in upstream windows" (Bjorn Helgaas)
AER
- Avoid info leak in __print_tlp_header() (Rasmus Villemoes)
PCI device hotplug
- Add missing curly braces in cpci_configure_slot() (Dan Carpenter)
ST Microelectronics SPEAr13xx host bridge driver
- Drop __initdata from spear13xx_pcie_driver (Matwey V. Kornilov)
* tag 'pci-v4.0-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
Revert "sparc/PCI: Clip bridge windows to fit in upstream windows"
PCI: Don't look for ACPI hotplug parameters if ACPI is disabled
PCI: cpcihp: Add missing curly braces in cpci_configure_slot()
PCI/AER: Avoid info leak in __print_tlp_header()
PCI: spear: Drop __initdata from spear13xx_pcie_driver
Pull drm fixes from Dave Airlie:
"Final drm fixes: one core locking imbalance regression, and a bunch of
i915 baytrail s/r fixes"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm: fix drm_mode_getconnector() locking imbalance regression
drm/i915/vlv: remove wait for previous GFX clk disable request
drm/i915/chv: Remove Wait for a previous gfx force-off
drm/i915/vlv: save/restore the power context base reg
three commits, all cc: stable, to address Baytrail
suspend/resume issues.
* tag 'drm-intel-fixes-2015-04-08' of git://anongit.freedesktop.org/drm-intel:
drm/i915/vlv: remove wait for previous GFX clk disable request
drm/i915/chv: Remove Wait for a previous gfx force-off
drm/i915/vlv: save/restore the power context base reg
When the CONTINUE bit is set, the interrupt status we are polling to
identify if a transaction has finished can be sporadic. Even though
the transfer has finished, the interrupt status may erroneously
indicate that there is still data in the FIFO. This behaviour causes
random timeouts in large PIO transfers.
Instead of using the CONTINUE bit to control the CS lines, use the SPI
core's CS GPIO handling. Also, now that the CONTINUE bit is not being
used, we can poll for the ALLDONE interrupt to indicate transfer
completion.
Signed-off-by: Sifan Naeem <sifan.naeem@imgtec.com>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Imagination has recommended that the SPFI controller be reset after
each message, regardless of success or failure. Do this in an
unprepare_message() callback.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver can be greatly simplified by moving the transfer timeout
handling to a handle_err() callback.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
SCSI transport drivers and SCSI LLDs block a SCSI device if the
transport layer is not operational. This means that in this state
no requests should be processed, even if the REQ_PREEMPT flag has
been set. This patch avoids that a rescan shortly after a cable
pull sporadically triggers the following kernel oops:
BUG: unable to handle kernel paging request at ffffc9001a6bc084
IP: [<ffffffffa04e08f2>] mlx4_ib_post_send+0xd2/0xb30 [mlx4_ib]
Process rescan-scsi-bus (pid: 9241, threadinfo ffff88053484a000, task ffff880534aae100)
Call Trace:
[<ffffffffa0718135>] srp_post_send+0x65/0x70 [ib_srp]
[<ffffffffa071b9df>] srp_queuecommand+0x1cf/0x3e0 [ib_srp]
[<ffffffffa0001ff1>] scsi_dispatch_cmd+0x101/0x280 [scsi_mod]
[<ffffffffa0009ad1>] scsi_request_fn+0x411/0x4d0 [scsi_mod]
[<ffffffff81223b37>] __blk_run_queue+0x27/0x30
[<ffffffff8122a8d2>] blk_execute_rq_nowait+0x82/0x110
[<ffffffff8122a9c2>] blk_execute_rq+0x62/0xf0
[<ffffffffa000b0e8>] scsi_execute+0xe8/0x190 [scsi_mod]
[<ffffffffa000b2f3>] scsi_execute_req+0xa3/0x130 [scsi_mod]
[<ffffffffa000c1aa>] scsi_probe_lun+0x17a/0x450 [scsi_mod]
[<ffffffffa000ce86>] scsi_probe_and_add_lun+0x156/0x480 [scsi_mod]
[<ffffffffa000dc2f>] __scsi_scan_target+0xdf/0x1f0 [scsi_mod]
[<ffffffffa000dfa3>] scsi_scan_host_selected+0x183/0x1c0 [scsi_mod]
[<ffffffffa000edfb>] scsi_scan+0xdb/0xe0 [scsi_mod]
[<ffffffffa000ee13>] store_scan+0x13/0x20 [scsi_mod]
[<ffffffff811c8d9b>] sysfs_write_file+0xcb/0x160
[<ffffffff811589de>] vfs_write+0xce/0x140
[<ffffffff81158b53>] sys_write+0x53/0xa0
[<ffffffff81464592>] system_call_fastpath+0x16/0x1b
[<00007f611c9d9300>] 0x7f611c9d92ff
Reported-by: Max Gurtuvoy <maxg@mellanox.com>
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: <stable@vger.kernel.org>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Kernel panic was happening as iscsi_host_remove() was called on
a host which was not yet added.
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: <stable@vger.kernel.org>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Booting a v3.18 or newer Xen domU kernel with PCI devices passed through
results in an oops (this is a 32-bit 3.13.11 dom0 with a 64-bit 4.4.0
hypervisor and 32-bit domU):
BUG: unable to handle kernel paging request at 0030303e
IP: [<c06ed0e6>] acpi_ns_validate_handle+0x12/0x1a
Call Trace:
[<c06eda4d>] ? acpi_evaluate_object+0x31/0x1fc
[<c06b78e1>] ? pci_get_hp_params+0x111/0x4e0
[<c0407bc7>] ? xen_force_evtchn_callback+0x17/0x30
[<c04085fb>] ? xen_restore_fl_direct_reloc+0x4/0x4
[<c0699d34>] ? pci_device_add+0x24/0x450
Don't look for ACPI configuration information if ACPI has been disabled.
I don't think this is the best fix, because we can boot plain Linux (no
Xen) with "acpi=off", and we don't need this check in pci_get_hp_params().
There should be a better fix that would make Xen domU work the same way.
The domU kernel has ACPI support but it has no AML. There should be a way
to initialize the ACPI data structures so things fail gracefully rather
than oopsing. This is an interim fix to address the regression.
Fixes: 6cd33649fa ("PCI: Add pci_configure_device() during enumeration")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=96301
Reported-by: Michael D Labriola <mlabriol@gdeb.com>
Tested-by: Michael D Labriola <mlabriol@gdeb.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org # v3.18+
Setting the transfer length in the TRANSACTION register after the
CONTROL register is programmed causes intermittent timeout issues in
SPFI transfers when using the SPI framework to control the CS GPIO
lines. To avoid this issue, set transfer length before programming
the CONTROL register.
Signed-off-by: Sifan Naeem <sifan.naeem@imgtec.com>
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Regression in commit 2caa80e72b
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Sun Feb 22 11:38:36 2015 +0100
drm: Fix deadlock due to getconnector locking changes
If the drm_connector_find() call returns NULL, we should no longer
call drm_modeset_unlock() to avoid locking imbalance.
Signed-off-by: Tommi Rantala <tt.rantala@gmail.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
"The domainname can be specified as either a DNS host name, a
dotted-decimal IPv4 address, or a bracketed IPv6 address as specified
in [RFC2732]."
See https://bugzilla.redhat.com/show_bug.cgi?id=1206868
Reported-by: Kyle Brantley <kyle@averageurl.com>
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Simple patch to make symbols static. Symbols that are not
shared with other parts of the kernel can be made static.
This change also removes several sparse complains.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Ajit Pal Singh <ajitpal.singh@st.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Some temperature sensors only get updated every few seconds and while
waiting for the first irq reporting a (new) temperature to happen there
get_temp operand will return -EAGAIN as it does not have any data to report
yet.
Not logging an error in this case avoids messages like these from showing
up in dmesg on affected systems:
[ 1.219353] thermal thermal_zone0: failed to read out thermal zone 0
[ 2.015433] thermal thermal_zone0: failed to read out thermal zone 0
[ 2.416737] thermal thermal_zone0: failed to read out thermal zone 0
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
If a driver doesn't implement the master->handle_err() callback and an
SPI transfer fails, the kernel will crash with a NULL pointer
dereference:
Unable to handle kernel NULL pointer dereference at virtual address 00000000
pgd = c0003000
[00000000] *pgd=80000040004003, *pmd=00000000
Internal error: Oops: 80000206 [#1] SMP ARM
Modules linked in:
CPU: 1 PID: 1 Comm: swapper/0 Not tainted 4.0.0-rc7-koelsch-05861-g1fc9fdd4add4f783 #1046
Hardware name: Generic R8A7791 (Flattened Device Tree)
task: eec359c0 ti: eec54000 task.ti: eec54000
PC is at 0x0
LR is at spi_transfer_one_message+0x1cc/0x1f0
Make the master->handle_err() callback optional to avoid the crash.
Also fix a spelling mistake in the callback documentation while we're at
it.
Fixes: b716c4ffc6 ("spi: introduce master->handle_err() callback")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
Looks like it was introduced in:
commit 650ad970a3
Author: Imre Deak <imre.deak@intel.com>
Date: Fri Apr 18 16:35:02 2014 +0300
drm/i915: vlv: factor out vlv_force_gfx_clock and check for pending force-of
but I'm not sure why. It has caused problems for us in the past (see
85250ddff7 "drm/i915/chv: Remove Wait for a previous gfx force-off"
and 8d4eee9cd7 "drm/i915: vlv: increase timeout when forcing on the
GFX clock") and doesn't seem to be required, so let's just drop it.
References: https://bugs.freedesktop.org/show_bug.cgi?id=89611
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: Darren Hart <dvhart@linux.intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Cc: stable@vger.kernel.org # c9c52e2419: drm/i915/chv: Remove Wait ...
Cc: stable@vger.kernel.org
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
On CHV, PUNIT team confirmed that 'VLV_GFX_CLK_STATUS_BIT' is not a
sticky bit and it will always be set. So ignore Check for previous
Gfx force off during suspend and allow the force clk as part S0ix
Sequence
Signed-off-by: Deepak S <deepak.s@linux.intel.com>
Cc: stable@vger.kernel.org
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Some BIOSes (e.g. the one on the Minnowboard) don't save/restore this
reg. If it's unlocked, we can just restore the previous value, and if
it's locked (in case the BIOS re-programmed it for us) the write will be
ignored and we'll still have "did it move" sanity check in the PM code to
warn us if something is still amiss.
References: https://bugs.freedesktop.org/show_bug.cgi?id=89611
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: Darren Hart <dvhart@linux.intel.com>
Cc: stable@vger.kernel.org
Reviewed-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Although the SPFI BITCLK divider supports a value of up to 255, only
values up to 128 are usable. This results in a maximum possible bit
clock rate of 1/4th the input clock rate.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
In preparation for switching to using the SPI core's CS GPIO handling,
move setup of the PORT_STATE register, which must be configured before
CS is asserted, to a prepare_message() callback.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>