In upcoming changes, SR-IOV VF migration data will be extended beyond
GuC data and exported to userspace using VFIO interface (with a
vendor-specific variant driver) and a device-level debugfs interface.
Remove the GT-level debugfs.
Reviewed-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Link: https://patch.msgid.link/20251112132220.516975-14-michal.winiarski@intel.com
Signed-off-by: Michał Winiarski <michal.winiarski@intel.com>
Contiguous PF GGTT VMAs can be scarce after creating VFs.
Increase the GuC buffer cache size to 8M for PF so that we can fit GuC
migration data (which currently maxes out at just over 4M) and use the
cache instead of allocating fresh BOs.
Reviewed-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Link: https://patch.msgid.link/20251112132220.516975-13-michal.winiarski@intel.com
Signed-off-by: Michał Winiarski <michal.winiarski@intel.com>
An upcoming change will use GuC buffer cache as a place where GuC
migration data will be stored, and the memory requirement for that is
larger than indirect data.
Allow the caller to pass the size based on the intended usecase.
Reviewed-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Link: https://patch.msgid.link/20251112132220.516975-12-michal.winiarski@intel.com
Signed-off-by: Michał Winiarski <michal.winiarski@intel.com>
In upcoming changes the cached buffers are going to be used to read data
produced by the GuC. Add a counterpart to flush, which synchronizes the
CPU-side of suballocation with the GPU data and propagate the interface
to GuC Buffer Cache.
Reviewed-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Link: https://patch.msgid.link/20251112132220.516975-11-michal.winiarski@intel.com
Signed-off-by: Michał Winiarski <michal.winiarski@intel.com>
The size is normally used to make a decision on when to stop the device
(mainly when it's in a pre_copy state).
Reviewed-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Link: https://patch.msgid.link/20251112132220.516975-10-michal.winiarski@intel.com
Signed-off-by: Michał Winiarski <michal.winiarski@intel.com>
The descriptor reuses the KLV format used by GuC and contains metadata
that can be used to quickly fail migration when source is incompatible
with destination.
Reviewed-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Link: https://patch.msgid.link/20251112132220.516975-9-michal.winiarski@intel.com
Signed-off-by: Michał Winiarski <michal.winiarski@intel.com>
Add debugfs handlers for migration state and handle bitstream
.read()/.write() to convert from bitstream to/from migration data
packets.
As descriptor/trailer are handled at this layer - add handling for both
save and restore side.
Reviewed-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Link: https://patch.msgid.link/20251112132220.516975-8-michal.winiarski@intel.com
Signed-off-by: Michał Winiarski <michal.winiarski@intel.com>
Now that it's possible to free the packets - connect the restore
handling logic with the ring.
The helpers will also be used in upcoming changes that will start
producing migration data packets.
Reviewed-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Link: https://patch.msgid.link/20251112132220.516975-7-michal.winiarski@intel.com
Signed-off-by: Michał Winiarski <michal.winiarski@intel.com>
Migration data is queued in a per-GT ptr_ring to decouple the worker
responsible for handling the data transfer from the .read() and .write()
syscalls.
Add the data structures and handlers that will be used in future
commits.
Reviewed-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Link: https://patch.msgid.link/20251112132220.516975-6-michal.winiarski@intel.com
Signed-off-by: Michał Winiarski <michal.winiarski@intel.com>
The states will be used by upcoming changes to produce (in case of save)
or consume (in case of resume) the VF migration data.
Reviewed-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Link: https://patch.msgid.link/20251112132220.516975-5-michal.winiarski@intel.com
Signed-off-by: Michał Winiarski <michal.winiarski@intel.com>
Upcoming changes will allow users to control VF state and obtain its
migration data with a device-level granularity (not tile/gt).
Change the data structures to reflect that and move the GT-level
migration init to happen after device-level init.
Reviewed-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Link: https://patch.msgid.link/20251112132220.516975-3-michal.winiarski@intel.com
Signed-off-by: Michał Winiarski <michal.winiarski@intel.com>
Since commit 4eb0aab6e4 ("drm/xe/guc: Bump minimum required GuC
version to v70.29.2"), the minimum GuC version required by the driver
is v70.29.2, which should already include everything that we need for
migration.
Remove the version check.
Suggested-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Reviewed-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Link: https://patch.msgid.link/20251112132220.516975-2-michal.winiarski@intel.com
Signed-off-by: Michał Winiarski <michal.winiarski@intel.com>
Add a default case to the switch case statement in mipi_exec_send_packet
to prevent attempts to read an uninitialized ret value. It's unlikely
the default case will ever occur during regular exeuction, but if more
MIPI DSI Processor-to-Peripheral transaction types are ever added, then
having this in place will be a useful safety guard.
Signed-off-by: Jonathan Cavitt <jonathan.cavitt@intel.com>
Fixes: 23db1577ce ("drm/i915/dsi: log send packet sequence errors")
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patch.msgid.link/20251104164150.16795-2-jonathan.cavitt@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Remove the cached pc->rpa_freq field and refactor RPA frequency handling
to fetch values directly from hardware registers on each request.
v2: Check graphics version instead of platform (Rodrigo)
v3: Fix graphics version check (Badal)
Suggested-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Suggested-by: Badal Nilawar <badal.nilawar@intel.com>
Signed-off-by: Sk Anirban <sk.anirban@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patch.msgid.link/20251112185153.3593145-6-sk.anirban@intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
RPe is runtime-determined by PCODE and caching it caused stale values,
leading to incorrect GuC SLPC parameter settings.
Drop the cached rpe_freq field and query fresh values from hardware
on each use to ensure GuC SLPC parameters reflect current RPe.
v2: Remove cached RPe frequency field (Rodrigo)
v3: Remove extra variable (Vinay)
Modify function name (Vinay)
v4: Maintain a separate function for PVC (Rodrigo)
v5: Avoid RPn update while fetching RPe frequency (Rodrigo)
v6: Split platform-specific RPe comments (Vinay)
Closes: https://gitlab.freedesktop.org/drm/xe/kernel/-/issues/5166
Signed-off-by: Sk Anirban <sk.anirban@intel.com>
Reviewed-by: Vinay Belgaumkar <vinay.belgaumkar@intel.com>
Link: https://patch.msgid.link/20251112185153.3593145-5-sk.anirban@intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
The if+ternary combo used for the max cursor width initialization
on 845/865 is rather cumbersome. Just split this into a straight
up if ladder.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patch.msgid.link/20251107181126.5743-10-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Move the max cursor size initialization into intel_cursor.c
so that all the platform specific details about cursors are
concentrated in one file.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patch.msgid.link/20251107181126.5743-9-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Replace the hardcoded 256 with mode_config->cursor_width
when doing the cursor DDB allocation. Currently 256 is correct
for all SKL+, but this might change in the future. One less place
to change should that happen.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patch.msgid.link/20251107181126.5743-8-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Replace the technically inaccurate drm_format_info() with the
accurate drm_get_format_info() in the SKL+ cursor DDB
allocation code.
Since we're only interested in the linear modifier here, the two
functions do actually return the same information. But let's not
use drm_format_info() to avoid setting a bad example.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patch.msgid.link/20251107181126.5743-7-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Make the order of things a bit less fragile in
intel_framebuffer_init() by assigning 'ret' in each
error branch instead of depending on some earlier
assignment.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patch.msgid.link/20251107181126.5743-6-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Use intel_fb_modifier_to_tiling() to convert the modifier into
the fence tiling mode during BIOS FB readout, rather than hand
rolling it. With this we can also stop tracking the tiling mode
in the intel_plane_config.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patch.msgid.link/20251107181126.5743-5-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Use drm_get_format_info() instead of drm_format_info() to populate
fb->format during the BIOS FB readout. The difference being that
drm_get_format_info() knows about compressed formats whereas
drm_format_info() doesn't.
This doesn't actually matter in practice since the BIOS FB should
never be compressed, but no reason we shouldn't use the more accurate
function here anyway.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patch.msgid.link/20251107181126.5743-4-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Pass the format info into plane->max_stride() from the
caller instead of doing yet another drm_format_info()
lookup on the spot.
drm_format_info() is both rather expensive, and technically
incorrect since it doesn't return the correct format info
for compressed formats (though that doesn't actually matter
for the current .max_stride() implementations since they
are just interested in the cpp value).
Most callers already have the format info available. The
only exception is intel_dumb_fb_max_stride() where we shall
use the actually correct drm_get_format_info() variant.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patch.msgid.link/20251107181126.5743-3-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Wrap intel_plane_fb_max_stride() in intel_dumb_fb_max_stride()
for the purposes of dumb fb creation. I want to change
intel_plane_fb_max_stride() to take a 'struct drm_format_info'
instead of the 'u32 pixel_format' so we need an excplicit format
info lookup in the dumb fb path and I don't really want to have
that in i915_gem_dumb_create() directly.
This makes intel_plane_fb_max_stride() internal to the display
code again, and thus we can pass in struct intel_display instead
of struct drm_device.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patch.msgid.link/20251107181126.5743-2-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Add the missing fields of the nvfw_hs_load_header_v2 struct, so that the
struct matches the actual contents of the firmware images.
nvfw_hs_load_header_v2 is a struct that defines a header for some firmware
images used by Nouveau. The current structure definition is incomplete;
it omits the last two fields because they are unused.
To maintain consistency between Nouveau, OpenRM, and Nova, and to
make it easier to support possible future images, we should fully define
the struct. Also add a __counted_by tag for the flex array.
Signed-off-by: Timur Tabi <ttabi@nvidia.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patch.msgid.link/20251010223957.1078525-1-ttabi@nvidia.com
The HW can only do compression on large and huge pages, and enabling it on
4K pages leads to a MMU fault. Compression also needs kernel support for
handling the compressed kinds and managing the compression tags.
This increments the nouveau version number which allows NVK to enable it
only when the kernel actually supports both features and avoid breaking
the system if a newer mesa version is paired with an older kernel version.
For the associated userspace MR, please see !36450:
https://gitlab.freedesktop.org/mesa/mesa/-/merge_requests/36450
Signed-off-by: Mohamed Ahmed <mohamedahmedegypt2001@gmail.com>
Signed-off-by: Mary Guillemard <mary@mary.zone>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: James Jones <jajones@nvidia.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patch.msgid.link/20251110-nouveau-compv6-v6-5-83b05475f57c@mary.zone
Allow compressed PTE kinds to be written into PTEs when GSP-RM is
present, rather than reverting to their non-compressed versions.
Signed-off-by: Ben Skeggs <bskeggs@nvidia.com>
Signed-off-by: Mohamed Ahmed <mohamedahmedegypt2001@gmail.com>
Signed-off-by: Mary Guillemard <mary@mary.zone>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: James Jones <jajones@nvidia.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patch.msgid.link/20251110-nouveau-compv6-v6-4-83b05475f57c@mary.zone
From GP100 onwards it's not possible to initialise comptag RAM without
PMU firmware, which nouveau has no support for.
As such, this code is essentially a no-op and will always revert to the
equivalent non-compressed kind due to comptag allocation failure. It's
also broken for the needs of VM_BIND/Vulkan.
Remove the code entirely to make way for supporting compression on GPUs
that support GSM-RM.
Signed-off-by: Ben Skeggs <bskeggs@nvidia.com>
Signed-off-by: Mohamed Ahmed <mohamedahmedegypt2001@gmail.com>
Signed-off-by: Mary Guillemard <mary@mary.zone>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: James Jones <jajones@nvidia.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patch.msgid.link/20251110-nouveau-compv6-v6-3-83b05475f57c@mary.zone
Now that everything in UVMM knows about the variable page shift, we can
select larger values.
The proposed approach relies on nouveau_bo::page unless if it would cause
alignment issues (in which case we fall back to searching for an
appropriate shift)
Signed-off-by: Mary Guillemard <mary@mary.zone>
Co-developed-by: Mohamed Ahmed <mohamedahmedegypt2001@gmail.com>
Signed-off-by: Mohamed Ahmed <mohamedahmedegypt2001@gmail.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: James Jones <jajones@nvidia.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patch.msgid.link/20251110-nouveau-compv6-v6-2-83b05475f57c@mary.zone
Currently memory allocated by VM_BIND uAPI can only have a granuality
matching PAGE_SIZE (4KiB in common case)
To have a better memory management and to allow big (64KiB) and huge
(2MiB) pages later in the series, we are now passing the page shift all
around the internals of UVMM.
Signed-off-by: Mary Guillemard <mary@mary.zone>
Co-developed-by: Mohamed Ahmed <mohamedahmedegypt2001@gmail.com>
Signed-off-by: Mohamed Ahmed <mohamedahmedegypt2001@gmail.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: James Jones <jajones@nvidia.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patch.msgid.link/20251110-nouveau-compv6-v6-1-83b05475f57c@mary.zone
Some driver components, like eudebug or ccs-mode, can't be used
when VFs are enabled. Add functions to allow those components
to block the PF from enabling VFs for the requested duration.
Introduce trivial counter to allow lockdown or exclusive access
that can be used in the scenarios where we can't follow the strict
owner semantics as required by the rw_semaphore implementation.
Before enabling VFs, the PF will try to arm the "vfs_enabling"
guard for the exclusive access. This will fail if there are
some lockdown requests already initiated by the other components.
For testing purposes, add debugfs file which will call these new
functions from the file's open/close hooks.
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Matthew Brost <matthew.brost@intel.com>
Cc: Christoph Manszewski <christoph.manszewski@intel.com>
Reviewed-by: Christoph Manszewski <christoph.manszewski@intel.com>
Link: https://patch.msgid.link/20251109162451.4779-1-michal.wajdeczko@intel.com
The sparse array used for error decoding from is unnecessarily big. It
should be better handled by a switch statement that will also allow us
to more easily improve this code.
Add a CASE_ERR() macro to keep the table compact and use it instead of
the 256-entries array, which saves some space:
$ bloat-o-meter xe_pcode.o.old xe_pcode.o
add/remove: 0/1 grow/shrink: 2/0 up/down: 190/-4096 (-3906)
Function old new delta
__pcode_mailbox_rw 363 465 +102
__pcode_mailbox_rw.cold 58 146 +88
err_decode 4096 - -4096
Total: Before=7890, After=3984, chg -49.51%
Reviewed-by: Raag Jadav <raag.jadav@intel.com>
Link: https://patch.msgid.link/20251110-pcode-errmap-v2-1-cb18c8f54238@intel.com
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Disable Panel Replay on MST links until it's properly implemented. For
instance the required VSC SDP is not programmed on MST and FEC is not
enabled if Panel Replay is enabled.
Fixes: 3257e55d3e ("drm/i915/panelreplay: enable/disable panel replay")
Closes: https://gitlab.freedesktop.org/drm/i915/kernel/-/issues/15174
Cc: Jouni Högander <jouni.hogander@intel.com>
Cc: Animesh Manna <animesh.manna@intel.com>
Cc: stable@vger.kernel.org # v6.8+
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patch.msgid.link/20251107124141.911895-1-imre.deak@intel.com
(cherry picked from commit e109f644b8)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Documentation build reported:
WARNING: ./drivers/gpu/drm/xe/xe_pm.c:131 expecting prototype for xe_pm_might_block_on_suspend(). Prototype was for xe_pm_block_on_suspend() instead
The kernel-doc comment for xe_pm_block_on_suspend() incorrectly used
the function name xe_pm_might_block_on_suspend(). Fix the header to
match the actual function prototype.
No functional changes.
Fixes: f73f6dd312 ("drm/xe/pm: Add lockdep annotation for the pm_block completion")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202511061736.CiuroL7H-lkp@intel.com/
Signed-off-by: Kriish Sharma <kriish.sharma2006@gmail.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patch.msgid.link/20251110184206.2113830-1-kriish.sharma2006@gmail.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
After integrating OLDI support[0], it is necessary to identify which VP
instances use OLDI, since the OLDI driver owns the video port clock
(as a serial clock). Clock operations on these VPs must be delegated to
the OLDI driver, not handled by the TIDSS driver. This issue also
emerged in upstream discussions when DSI-related clock management was
attempted in the TIDSS driver[1].
To address this, add an 'is_ext_vp_clk' array to the 'tidss_device'
structure, marking a VP as 'true' during 'tidss_oldi_init()' and as
'false' during 'tidss_oldi_deinit()'. TIDSS then uses 'is_ext_vp_clk'
to skip clock validation checks in 'dispc_vp_mode_valid()' for VPs
under OLDI control.
Since OLDI uses the DSS VP clock directly as a serial interface and
manages its own rate, mode validation should be implemented in the OLDI
bridge's 'mode_valid' hook. This patch adds that logic, ensuring proper
delegation and avoiding spurious clock handling in the TIDSS driver.
[0]: https://lore.kernel.org/all/20250528122544.817829-1-aradhya.bhatia@linux.dev/
[1]: https://lore.kernel.org/all/DA6TT575Z82D.3MPK8HG5GRL8U@kernel.org/
Fixes: 7246e09299 ("drm/tidss: Add OLDI bridge support")
Tested-by: Michael Walle <mwalle@kernel.org>
Reviewed-by: Devarsh Thakkar <devarsht@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Signed-off-by: Swamil Jain <s-jain1@ti.com>
Link: https://patch.msgid.link/20251104151422.307162-3-s-jain1@ti.com
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Link: https://patch.msgid.link/ffd5ebe03391b3c01e616c0c844a4b8ddecede36.1762513240.git.jani.nikula@intel.com
The TIDSS hardware does not have independent maximum or minimum pixel
clock limits for each video port. Instead, these limits are determined
by the SoC's clock architecture. Previously, this constraint was
modeled using the 'max_pclk_khz' and 'min_pclk_khz' fields in
'dispc_features', but this approach is static and does not account for
the dynamic behavior of PLLs.
This patch removes the 'max_pclk_khz' and 'min_pclk_khz' fields from
'dispc_features'. The correct way to check if a requested mode's pixel
clock is supported is by using 'clk_round_rate()' in the 'mode_valid()'
hook. If the best frequency match for the mode clock falls within the
supported tolerance, it is approved. TIDSS supports a 5% pixel clock
tolerance, which is now reflected in the validation logic.
This change allows existing DSS-compatible drivers to be reused across
SoCs that only differ in their pixel clock characteristics. The
validation uses 'clk_round_rate()' for each mode, which may introduce
additional delay (about 3.5 ms for 30 modes), but this is generally
negligible. Users desiring faster validation may bypass these calls
selectively, for example, checking only the highest resolution mode,
as shown here[1].
[1]: https://lore.kernel.org/all/20250704094851.182131-3-j-choudhary@ti.com/
Tested-by: Michael Walle <mwalle@kernel.org>
Reviewed-by: Devarsh Thakkar <devarsht@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Signed-off-by: Swamil Jain <s-jain1@ti.com>
Link: https://patch.msgid.link/20251104151422.307162-2-s-jain1@ti.com
[Tomi: dropped 'inline' from check_pixel_clock]
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
It's not used anymore, so remove it. This allows trully independent
layer state from mixer.
Reviewed-by: Chen-Yu Tsai <wens@kernel.org>
Tested-by: Ryan Walklin <ryan@testtoast.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://patch.msgid.link/20251104180942.61538-31-jernej.skrabec@gmail.com
Signed-off-by: Chen-Yu Tsai <wens@kernel.org>
This allows to almost completely decouple layer code from mixer. This is
important for DE33.
Reviewed-by: Chen-Yu Tsai <wens@kernel.org>
Tested-by: Ryan Walklin <ryan@testtoast.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://patch.msgid.link/20251104180942.61538-29-jernej.skrabec@gmail.com
Signed-off-by: Chen-Yu Tsai <wens@kernel.org>
Later special plane only driver for DE33 will provide separate
configuration. This change will also help layer driver migrate away from
mixer structure.
Reviewed-by: Chen-Yu Tsai <wens@kernel.org>
Tested-by: Ryan Walklin <ryan@testtoast.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://patch.msgid.link/20251104180942.61538-28-jernej.skrabec@gmail.com
Signed-off-by: Chen-Yu Tsai <wens@kernel.org>
On DE2 and DE3, UI scalers are located right after VI scalers. So in
order to calculate proper UI scaler base address, number of VI scalers
must be known. In practice, it is same as number of VI channels, but it
doesn't need to be.
Let's make a quirk for this number. Code for configuring channels and
associated functions won't have access to vi_num quirk anymore after
rework for independent planes.
Reviewed-by: Chen-Yu Tsai <wens@kernel.org>
Tested-by: Ryan Walklin <ryan@testtoast.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://patch.msgid.link/20251104180942.61538-27-jernej.skrabec@gmail.com
Signed-off-by: Chen-Yu Tsai <wens@kernel.org>
They can't be triggered if mixer configuration is properly specified in
quirks. Additionally, number of VI channels won't be available in future
due to rework for DE33 support.
Reviewed-by: Chen-Yu Tsai <wens@kernel.org>
Tested-by: Ryan Walklin <ryan@testtoast.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://patch.msgid.link/20251104180942.61538-26-jernej.skrabec@gmail.com
Signed-off-by: Chen-Yu Tsai <wens@kernel.org>
Determination if FCC unit can be used for VI layer alpha depends on
number of VI channels. This info won't be available anymore in future
to VI layer driver because of DE33 way of allocating planes from same
pool to different mixers.
While order is slightly changed, it doesn't affect anything due to
double buffering of registers. New order keeps related registers
together and quirk separate.
Reviewed-by: Chen-Yu Tsai <wens@kernel.org>
Tested-by: Ryan Walklin <ryan@testtoast.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://patch.msgid.link/20251104180942.61538-25-jernej.skrabec@gmail.com
Signed-off-by: Chen-Yu Tsai <wens@kernel.org>
Now that channel base calculation is straightforward, let's update VI
scaler base calculation to be simpler. At the same time, also introduce
macro to avoid magic numbers.
Note, reason why current magic value and new macro value isn't the same
is because sun8i_channel_base() already introduces offset to channel
registers. Previous value is just the difference to VI scaler registers.
However, new code calculates scaler base from channel base. This is also
easier to understand when looking into BSP driver. Macro value can be
easily found whereas old diff value was not.
Reviewed-by: Chen-Yu Tsai <wens@kernel.org>
Tested-by: Ryan Walklin <ryan@testtoast.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://patch.msgid.link/20251104180942.61538-24-jernej.skrabec@gmail.com
Signed-off-by: Chen-Yu Tsai <wens@kernel.org>
