spinand_mtd_regular_page_read() returns ret after iterating over the
requested pages. If the request contains no data or OOB bytes, the
iterator does not run and ret is not assigned. Initialize it to 0 for the
empty request path.
Signed-off-by: Ruoyu Wang <ruoyuw560@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Implement the 'set_randomizer' callback for Macronix SPI NAND chips.
The randomizer is enabled by setting bit 1 of the Configuration Register
(address 0x10).
This patch adds support for the following chips:
- MX35LFxG24AD series
- MX35UFxG24AD series
When the randomizer is enabled, data is scrambled internally during
program operations and automatically descrambled during read operations.
This helps reduce bit errors caused by program disturbance.
Please refer to the following link for randomizer feature:
Link: https://www.mxic.com.tw/Lists/ApplicationNote/Attachments/2151/AN1051V1-The%20Introduction%20of%20Randomizer%20Feature%20on%20MX30xFxG28AD_MX35xFxG24AD.pdf
Signed-off-by: Cheng Ming Lin <chengminglin@mxic.com.tw>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
This patch adds support for the randomizer feature.
It introduces a 'set_randomizer' callback in 'struct spinand_info' and
'struct spinand_device'.
If a driver implements this callback, the core will invoke it during
device initialization (spinand_init) to enable or disable the randomizer
feature based on the device tree configuration.
Signed-off-by: Cheng Ming Lin <chengminglin@mxic.com.tw>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Some controllers do not have full control over the CS line state and may
deassert it under certain conditions in the middle of a (long)
transfer.
Continuous reads are stopped with a CS deassert, hence both features
cannot live together.
Whenever a controller flags that it cannot maintain the CS state
reliably, disable continuous reads entirely.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Recent changes made sure whenever we were using continuous reads, we
would first start by disabling the feature to ensure a well proven and
stable probe sequence. For development purposes, it might also matter to
make sure we always disable continuous reads at first, in case the ECC
configuration would change. Doing this "automatically" will become even
more relevant when we add extra controller flags to prevent continuous
reads at all.
Ensure we disable continuous reads if the feature is available on the
chip, regardless of whether it will be used or not.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
As for the W35NxxJW family, add support for W25N{01,02}JW continuous
read support. Similar operations require to be done, such as setting a
specific bit in a configuration register, and providing a set of read
variants without the address cycles.
As read from cache variants are badly supported by SPI memory
controllers, we create a new set of read from cache templates with a
fake address cycle and just enough dummy cycles. There are two
unsupported configurations (which would require 4.5 dummy bytes), so we
just do not provide them.
The same extra value in the ECC is possible as with the W35NxxJW family,
so we reference the same helper to retrieve the ECC status.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
---
All variants have been validated on a Nuvoton MA35D1 platform.
The logic is not complex but might be reused to cleanup a bit the
section by moving it to a dedicated helper.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Updating the HS bit is not complex but implies reading, setting/clearing
a bit and writing. Clean a bit this section by moving this logic in its
own helper.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
W35N{01,02,04}JW support being read continuously under certain
circumstances. A bit must be set in their configuration register, and
a specific read from cache operation, a bit shorter than usual because
it no longer requires the address cycles, must be used for the occasion.
Setting the "enable" bit is already supported by the core, aside from
the subtlety of making sure the HFREQ bit is also set in octal DTR mode
above 90MHz. However, handling two different read from cache templates
involves creating a list of read from cache variants adapted the
continuous reads, ie. without address cycles.
Unfortunately, these operations, despite being very close to their
original read from cache cousins, are often unsupported by smart SPI
controller drivers because reading from cache historically allowed
changing the offset at which the host would start by providing a 2-byte
column address. In order to prevent issues with this, it has been
decided to implement these variants with a single "ignored" address byte
(respectively two in the octal DTR case), further reducing the amount of
dummy cycles needed before the first bit of data.
Enabling continuous reads has a side effect: the ECC status register now
may also return the value b11, which means that more than 1
uncorrectable error happened during the read. This non standard
behaviour requires to re-implement, almost identically the "get ECC"
helper from the core, with just an extra case for this value (it is
prefixed "w25w35nxxjw" because all these chips have the same behaviour).
Speed gain is substantial, see below. The flash_speed -C benchmark has
been run on a TI AM62A7 LP SK with CPU power management disabled,
mounted with a W35N01JW chip.
1S-8S-8S:
1 page read speed is 15058 KiB/s
2 page read speed is 15058 KiB/s
3 page read speed is 16800 KiB/s
4 page read speed is 17066 KiB/s
5 page read speed is 18461 KiB/s
6 page read speed is 18461 KiB/s
7 page read speed is 19384 KiB/s
8 page read speed is 19692 KiB/s
9 page read speed is 19384 KiB/s
10 page read speed is 20000 KiB/s
11 page read speed is 20000 KiB/s
12 page read speed is 20000 KiB/s
13 page read speed is 20800 KiB/s
14 page read speed is 20363 KiB/s
15 page read speed is 20000 KiB/s
16 page read speed is 19692 KiB/s
32 page read speed is 19692 KiB/s
64 page read speed is 19692 KiB/s
8D-8D-8D:
1 page read speed is 23272 KiB/s
2 page read speed is 23272 KiB/s
3 page read speed is 28000 KiB/s
4 page read speed is 32000 KiB/s
5 page read speed is 34285 KiB/s
6 page read speed is 34285 KiB/s
7 page read speed is 36000 KiB/s
8 page read speed is 36571 KiB/s
9 page read speed is 36000 KiB/s
10 page read speed is 34285 KiB/s
11 page read speed is 36666 KiB/s
12 page read speed is 40000 KiB/s
13 page read speed is 41600 KiB/s
14 page read speed is 37333 KiB/s
15 page read speed is 40000 KiB/s
16 page read speed is 36571 KiB/s
32 page read speed is 42666 KiB/s
64 page read speed is 42666 KiB/s
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
---
Not all configurations have been tested/validated yet.
As for the W35NxxJW family, add support for W25N{01,02}JW continuous
read support. Similar operations require to be done, such as setting a
specific bit in a configuration register, and providing a set of read
variants without the address cycles.
As read from cache variants are badly supported by SPI memory
controllers, we create a new set of read from cache templates with a
fake address cycle and just enough dummy cycles. There are two
unsupported configurations (which would require 4.5 dummy bytes), so we
just do not provide them.
The same extra value in the ECC is possible as with the W35NxxJW family,
so we reference the same helper to retrieve the ECC status.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
In case a chip supports continuous reads, but uses a slightly different
cache operation for these, it may provide a secondary operation template
which will be used only during continuous cache read operations.
From a vendor driver point of view, enabling this feature implies
providing a new set of templates for these continuous read
operations. The core will automatically pick the fastest variant,
depending on the hardware capabilities.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
here focus on the shared spi-mem layer which is enhanced in order to
bring two new features:
- The possibility to fill a primary and a secondary operation template
in the direct mapping structure in order to support continuous reads
in SPI NAND, which may require two different read operations.
- SPI controllers may indicate possible CS instabilities over long
transfers by setting a boolean. This capability is related to the
previous one, the need for it has arised while testing SPI NAND
continuous reads with the Cadence QSPI controller which cannot, under
certain conditions, keep the CS asserted for the length of
an eraseblock-large transfer.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmn4m50ACgkQJWrqGEe9
VoSUzwf8D7an5inOVMcX2IsbXSkA6vKgrzjc1jG3rGiLrFks/bZyo0R8atp4pUsy
6WDkJfFyHg6IzU92N/37Kha8rnFp7um9OhfB/z2O/ztyqr9d1yM6QDtenknYr+WH
BwcuJ8zenyWuIY526Ar04REJ07s8MZpMUhcnUIw/KpvQiS12UR6NHgEaUrmIjtLD
GCKKFTGOY++9dgObo8ZrkrsLlVUhV5GyvCqUtBNNbADTNAt7j4m6YuyztS7rrmwb
b33RoZiWmG0szkUsTJJBDH15cMB/4wV2SoGm3wzsACHqJhCy0n9FvSVAXwcRm5l7
qOLedtMoBIIIIwBbHPsf0SySToy2ag==
=3qpz
-----END PGP SIGNATURE-----
Merge tag 'mtd/spi-mem-cont-read-for-7.2' into nand/next
Aside from preparation changes in the SPI NAND core, the changes carried
here focus on the shared spi-mem layer which is enhanced in order to
bring two new features:
- The possibility to fill a primary and a secondary operation template
in the direct mapping structure in order to support continuous reads
in SPI NAND, which may require two different read operations.
- SPI controllers may indicate possible CS instabilities over long
transfers by setting a boolean. This capability is related to the
previous one, the need for it has arised while testing SPI NAND
continuous reads with the Cadence QSPI controller which cannot, under
certain conditions, keep the CS asserted for the length of
an eraseblock-large transfer.
As of now, we only use a single operation template when creating SPI
memory direct mappings. With the idea to extend this possibility to 2,
rename the template to reflect that we are currently setting the
"primary" operation, and create a pointer in the same structure to point
to it.
From a user point of view, the op_tmpl name remains but becomes a
pointer, leading to minor changes in both the SPI NAND and SPI NOR
cores.
There is no functional change.
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Direct mappings are very static concepts, which allow us to reuse a
template to perform reads or writes in a very efficient manner after a
single initialization. With the introduction of pipelined ECC engines
for SPI controllers, the need to differentiate between an operation with
and without correction has arised. The chosen solution at that time has
been to create new direct mappings for these operations, jumping from 2
to 4 dirmaps per target. Enabling ECC was done by choosing the correct
dirmap.
Today, we need to further parametrize dirmaps. With the goal to enable
continuous reads on a wider range of devices, we will need more
flexibility regarding the read from cache operation template to pick at
run time, for instance to use shorter "continuous read from cache"
variants.
We could create other direct mappings, but it would increase the matrix
by a power of two, bringing the theoretical number of dirmaps to
8 (read/write, ecc, shorter read variants) per target. This grow is not
sustainable, so let's change how dirmaps work - a little bit.
Operations already carry an ECC parameter, use it to indicate whether
error correction is required or not. In practice this change happens
only at the core level, SPI controller drivers do not care about the
direct mapping structure in this case, they just pick whatever is in the
template as a base. As a result, we allow the core to dynamically change
the content of the templates.
He who can do more can do less, so during the checking steps, make sure
to enable the ECC requirement just for the time of the checks.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Since continuous reads may sometimes not be able to go past an erase
block boundary, it has been decided not to attempt longer reads and if
the user request is bigger, it will be split across eraseblocks.
As these request will anyway be handled correctly, there is no reason to
filter out cases where we would go over a target or a die, so drop this
limitation which had a side effect: any request to read more than the
content of an eraseblock would simply not benefit from the continuous
read feature.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
In most scenarios this variant is actually unused (VCR is written in
SSDR mode), but we need to provide an octal variant. The address is 24
bits but is sent over 4 bytes MSB first. This means we need to shift the
register address by one extra byte for the address to be correct.
I didn't catch this initially because the volatile register region is
256 bytes wide, so the write-then-read procedure did work with the small
register addresses I was using at that time: 0 and 1.
Fixes: 44a2f49b9b ("mtd: spinand: winbond: W35N octal DTR support")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Both W35N02JW and W35N04JW diverge from W35N01JW when it comes to the
"data read" operation in ODTR mode. In order to stuff more address
bits (up to 18), the second command byte is replaced by the most
significant address bits, keeping the number of address bytes to 2.
Fixes: 44a2f49b9b ("mtd: spinand: winbond: W35N octal DTR support")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Some devices stuff address bits in the double byte opcode (in place of
the repeated byte) in order to be able to increase the size of the
devices, without adding extra address bytes.
Create a flag to identify those devices. When the flag is set, use the
"packed" variant for the read data operation.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Factory default for this bit is "set" (at least on the chips I have),
but we must make sure it is actually set by Linux explicitly, as the
bit is writable by an earlier stage.
Fixes: 6a804fb72d ("mtd: spinand: winbond: add support for serial NAND flash")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Above 104MHz when in fast dual or quad I/O reads, the delay between
address and data cycles is too short. It is possible to reach higher
frequencies, up to 166MHz, by adding a few more dummy cycles through the
setting of the HS bit. Improve the condition for enabling this bit, and
also make sure we set it at soon as we go over 104MHz.
Fixes: f1a91175fa ("mtd: spinand: winbond: Enable high-speed modes on w25n0xjw")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
This was done entirely with mindless brute force, using
git grep -l '\<k[vmz]*alloc_objs*(.*, GFP_KERNEL)' |
xargs sed -i 's/\(alloc_objs*(.*\), GFP_KERNEL)/\1)/'
to convert the new alloc_obj() users that had a simple GFP_KERNEL
argument to just drop that argument.
Note that due to the extreme simplicity of the scripting, any slightly
more complex cases spread over multiple lines would not be triggered:
they definitely exist, but this covers the vast bulk of the cases, and
the resulting diff is also then easier to check automatically.
For the same reason the 'flex' versions will be done as a separate
conversion.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is the result of running the Coccinelle script from
scripts/coccinelle/api/kmalloc_objs.cocci. The script is designed to
avoid scalar types (which need careful case-by-case checking), and
instead replace kmalloc-family calls that allocate struct or union
object instances:
Single allocations: kmalloc(sizeof(TYPE), ...)
are replaced with: kmalloc_obj(TYPE, ...)
Array allocations: kmalloc_array(COUNT, sizeof(TYPE), ...)
are replaced with: kmalloc_objs(TYPE, COUNT, ...)
Flex array allocations: kmalloc(struct_size(PTR, FAM, COUNT), ...)
are replaced with: kmalloc_flex(*PTR, FAM, COUNT, ...)
(where TYPE may also be *VAR)
The resulting allocations no longer return "void *", instead returning
"TYPE *".
Signed-off-by: Kees Cook <kees@kernel.org>
The ofpart parsing in physmap-core has been prioritized.
There has been a series of conversion to scoped for each OF child
loops.
* Bindings
The bulk of the changes consists in binding fixes/updates to restrict
the use of undefined properties, which was almost inefficient in the
current form because of the nesting of partition nodes and the lack of
compatible strings sometimes.
These changes are accompanied by YAML conversions and the addition of a
dma-coherent property in the cdns,hp-nfc driver.
* SPI NAND
The major feature this release is the support for octal DTR
modes (8D-8D-8D).
Support for Foresee F35SQB002G chips has been added.
Other changes are small misc fixes.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmmPXI4ACgkQJWrqGEe9
VoQKJgf/YgI8L684Hq8OejCZYCoChZpTTvMmqmZ0CgRaZ157jcYTY5Od46pUpfEs
uSuoXW6+cuxdGeeUtyb3u5uJduO8r7UMjYLBqtMRGjvtfN9EDdhqVQWnRfCr9PoR
MS4moQa14tEakeP/u6stsmGLpzPkgiygcdTCWS4LhNoJ0LgkLjfBusQm6P5uqc+a
m/XS4Mg8SPj7pGjinu5KsvKWKiez6k4ExXiLM9p0TX/8iacFhGBrzKqv6zMiNyfL
p5ZS3ZLv9d79sLKOPlycfNO9LOp6O6ufn+zmuHQpTHGdlPegiNCoF1fOB9XZxc4A
iK9Z7b3ko9ta0HdjzRYkG/eFtTL0dQ==
=hnfP
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-7.0' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull MTD updates from Miquel Raynal:
"MTD:
- prioritize ofpart in physmap-core probing
- conversions to scoped for each OF child loops
Bindings:
- The bulk of the changes consists of binding fixes/updates to
restrict the use of undefined properties, which was mostly
ineffective in the current form because of the nesting of partition
nodes and the lack of compatible strings
- YAML conversions and the addition of a dma-coherent property in the
cdns,hp-nfc driver
SPI NAND:
- support for octal DTR modes (8D-8D-8D)
- support for Foresee F35SQB002G chips
And small misc fixes"
* tag 'mtd/for-7.0' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (65 commits)
mtd: spi-nor: hisi-sfc: fix refcounting bug in hisi_spi_nor_register_all()
mtd: spinand: fix NULL pointer dereference in spinand_support_vendor_ops()
mtd: rawnand: pl353: Add message about ECC mode
mtd: rawnand: pl353: Fix software ECC support
mtd: spinand: winbond: Remove unneeded semicolon
dt-bindings: mtd: cdns,hp-nfc: Add dma-coherent property
mtd: spinand: Disable continuous read during probe
mtd: spinand: add Foresee F35SQB002G flash support
mtd: spinand: winbond: W35N octal DTR support
mtd: spinand: Add octal DTR support
mtd: spinand: Warn if using SSDR-only vendor commands in a non SSDR mode
mtd: spinand: Give the bus interface to the configuration helper
mtd: spinand: Propagate the bus interface across core helpers
mtd: spinand: Add support for setting a bus interface
mtd: spinand: Gather all the bus interface steps in one single function
mtd: spinand: winbond: Configure the IO mode after the dummy cycles
mtd: spinand: winbond: Rename IO_MODE register macro
mtd: spinand: winbond: Fix style
mtd: spinand: winbond: Register W35N vendor specific operation
mtd: spinand: winbond: Register W25N vendor specific operation
...
The spinand_support_vendor_ops() helper unconditionally dereferences
info->vendor_ops. For chips that do not define vendor_ops, this pointer
is NULL, leading to a kernel panic during probe:
Unable to handle kernel NULL pointer dereference at virtual address
0000000000000008
Add a guard to return early when vendor_ops is NULL. This prevents the
crash and allows SPI NAND devices without vendor-specific operations to
be probed correctly.
Fixes: fbc7538782 ("mtd: spinand: List vendor specific operations and make sure they are supported")
Cc: stable@vger.kernel.org
Signed-off-by: Md Sadre Alam <quic_mdalam@quicinc.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Remove unnecessary semicolons reported by Coccinelle/coccicheck and the
semantic patch at scripts/coccinelle/misc/semicolon.cocci.
Signed-off-by: Chen Ni <nichen@iscas.ac.cn>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Macronix serial NAND devices with continuous read support do not
clear the configuration register on soft reset and lack a hardware
reset pin. When continuous read is interrupted (e.g., during reboot),
the feature remains enabled at the device level.
With continuous read enabled, the OOB area becomes inaccessible and
all reads are instead directed to the main area. As a result, during
partition allocation as part of MTD device registration, the first two
bytes of the main area for the master block are read and indicate that
the block is bad. This process repeats for every subsequent block for
the partition.
All reads and writes that reference the BBT find no good blocks and
fail.
The only paths for recovery from this state are triggering the
continuous read feature by way of raw MTD reads or through a NAND
device power drain.
Disable continuous read explicitly during spinand probe to ensure
quiescent feature state.
Fixes: 631cfdd052 ("mtd: spi-nand: Add continuous read support")
Cc: stable@vger.kernel.org
Signed-off-by: David LaPorte <dalaport@amazon.com>
Reviewed-by: Gunnar Kudrjavets <gunnarku@amazon.com>
Reviewed-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Extend the support for the W35N chip family by supporting the ODTR bus
interface. The chip is capable to run in this mode, which brings a
significant performance improvement.
1S-8S-8S:
# flash_speed /dev/mtd0 -c1 -d
eraseblock write speed is 7529 KiB/s
eraseblock read speed is 15058 KiB/s
8D-8D-8D:
# flash_speed /dev/mtd0 -c1 -d
eraseblock write speed is 9481 KiB/s
eraseblock read speed is 23272 KiB/s
This is +55% read speed and +26% write speed with the same hardware.
Tests have been conducted with a TI AM62A7 using the Cadence quad SPI
controller.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Create a new bus interface named ODTR for "octal DTR", which matches the
following pattern: 8D-8D-8D.
Add octal DTR support for all the existing core operations. Add a second
set of templates for this bus interface.
Give the possibility for drivers to register their read, write and
update cache variants as well as their vendor specific operations.
Check the SPI controller driver supports all the octal DTR commands that
we might need before switching to the ODTR bus interface.
Make the switch by calling ->configure_chip() with the ODTR
parameter. Fallback in case this step fails.
If someone ever attempts to suspend a chip in octal DTR mode, there are
changes that it will loose its configuration at resume. Prevent any
problem by explicitly switching back to SSDR while suspending. Note:
there is a limitation in the current approach, page I/Os are not
available as the dirmaps will be created for the ODTR bus interface if
that option is supported and not switched back to SSDR during
suspend. Switching them is possible but would be costly and would not
bring anything as right after resuming we will switch again to ODTR. In
case this capability is used for debug, developpers should mind to
destroy and recreate suitable direct mappings.
Finally, as a side effect, we increase the buffer for reading IDs to
6. No device at this point returns 6 bytes, but we support 5 bytes IDs,
which means in octal DTR mode we have no other choice than reading an
even number of bytes, hence 6.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Both Macronix and Winbond have chip specific operations which are SSDR
only. Trying to use them in an ODTR setup will fail and doing this is a
pure software bug. Warn explicitly in this case.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The chip configuration hook is the one responsible to actually switch
the switch between bus interfaces. It is natural to give it the bus
interface we expect with a new parameter. For now the only value we can
give is SSDR, but this is subject to change in the future, so add a bit
of extra logic in the implementations of this callback to make sure
both the core and the chip driver are aligned on the request.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
For now all drivers provide SSDR variants only. When we add support for
ODTR modes, there will be a need to differentiate the type of variant we
target as well as the need to check if we support one or the other type
of operations.
Pass this parameter to lower level helpers, which for now is unused, in
order to simplify the patch introducing ODTR support.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Create a bus interface enumeration, currently only containing the
one we support: SSDR, for single SDR, so any operation whose command is
sent over a single data line in SDR mode, ie. any operation matching
1S-XX-XX.
The main spinand_device structure gets a new parameter to store this
enumeration, for now unused. Of course it is set to SSDR during the SSDR
templates initialization to further clarify the state we are in at the
moment.
This member is subject to be used to know in which bus configuration we
and be updated by the core when we switch to faster mode(s).
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Writing the quad enable bit in one helper and doing the chip
configuration in another does not make much sense from a bus interface
setup point of view.
Instead, let's create a broader helper which is going to be in charge of
all the bus configuration steps at once. This will specifically allow to
transition to octal DDR mode, and even fallback to quad (if suppoorted)
or single mode otherwise.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
When we will change the bus interface, the action that actually performs
the transition is the IO mode register write. This means after the IO
mode register write, we should use the new bus interface. But the
->configure_chip() hook itself is not responsible of making this change
official, it is the caller that must act according to the return value.
Reorganize this helper to first configure the dummy cycles before
possibly switching to another bus interface.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Provide the Winbond W35N specific "write VCR register" operation to let
the core verify it is supported by the controller before using it.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Provide the Winbond W25N specific "select target" operation to let the
core verify it is supported by the controller before using it.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Provide the Macronix specific "read ECC status register" operation so
that the core can verify if it is supported by the controller before
using it.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
It is probably safe to expect that all SPI controller drivers will ever
support all the most basic SPI NAND operations, such as write enable,
register reads, page program, block erases, etc. However, what about
vendor specific operations? So far nobody complained about it, but as we
are about to introduce octal DTR support, and as none of the SPI NAND
instruction set is defined in any standard, we must remain careful about
these extra operations.
One way to make sure we do not blindly get ourselves in strange
situations with vendor commands failing silently is to make the check
once for all, while probing the chip. However at this stage we have no
such list, so let's add the necessary infrastructure to allow:
- registering vendor operations,
- checking they are actually supported when appropriate.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Winbond W35N* chips require a vendor specific operation to write their
VCR register (a configuration register, typically used for tuning the
number of dummy cycles and switching to a different bus
interface). Instead of defining this op only in the function that needs
it, hiding it from the core, make it a proper define like all other
spi-mem operations, and implement the necessary spinand_fill_*_op()
helper to make the SPINAND_OP() macro work. This way we can use it from
any function without any extra handling outside of this helper when we
will convert the core to support octal DDR busses.
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Winbond W25N* chips require a vendor specific operation to select the
target. Instead of defining this op only in the function that
needs it, hiding it from the core, make it a proper define like all
other spi-mem operations, and implement the necessary
spinand_fill_*_op() helper to make the SPINAND_OP() macro work. This way
we can use it from any function without any extra handling outside of
this helper when we will convert the core to support octal DDR busses.
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Macronix chips require a vendor specific operation to read the ECC
status register. Instead of defining this op only in the function that
needs it, hiding it from the core, make it a proper define like all
other spi-mem operations, and implement the necessary
spinand_fill_*_op() helper to make the SPINAND_OP() macro work. This way
we can use it from any function without any extra handling outside of
this helper when we will convert the core to support octal DDR busses.
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Create a SPINAND_OP() macro to which we give the name of the operation
we want. This macro retrieves the correct operation template based on
the current bus interface (currently only single SDR, will soon be
extended to octal DTR) and fills it with the usual parameters.
This macro makes the transition from calling directly the low-level
macros into using the (bus interface dependent) templates very smooth.
Use it in all places that can be trivially converted. At this stage
there is no functional change expected, until octal DTR support gets
added.
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Currently, the SPI NAND core implementation directly calls macros to get
the various operations in shape. These macros are specific to the bus
interface, currently only supporting the single SDR interface (any
command following the 1S-XX-XX pattern).
Introducing support for other bus interfaces (such as octal DTR) would
mean that every user of these macros should become aware of the current
bus interface and act accordingly, picking up and adapting to the
current configuration. This would add quite a bit of boilerplate, be
repetitive as well as error prone in case we miss one occurrence.
Instead, let's create a table with all SPI NAND memory operations that
are currently supported. We initialize them with the same single SDR _OP
macros as before. This opens the possibility for users of the individual
macros to make use of these templates instead. This way, when we will add
another bus interface, we can just switch to another set of templates
and all users will magically fill in their spi_mem_op structures with
the correct ops.
The existing read, write and update cache variants are also moved in
this template array, which is barely noticeable by callers as we also
add a structure member pointing to it.
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
In order to introduce templates for all operations and not only for page
helpers (in order to introduce octal DDR support), decouple the WR_EN
and WR_DIS operations into two separate macros.
Adapt the callers accordingly.
There is no functional change.
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Replace -ENOTSUPP with -EOPNOTSUPP which is as relevant in this case but
is standard.
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The update cache variant is mandatory, both read and write versions are
being checked, but not this one. All chip drivers seem to implement this
variant, so there should be no breakage.
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>