The IEEE 802.1Qaz standard defines that bandwidth allocation percentages
only apply to Enhanced Transmission Selection (ETS) traffic classes.
For STRICT and VENDOR transmission selection algorithms, bandwidth
percentage values are not applicable.
Currently for non-ETS 100 bandwidth is being reported for all traffic
classes in the get operation due to hardware limitation, regardless of
their TSA type.
Fix this by reporting 0 for non-ETS traffic classes.
Fixes: 820c2c5e77 ("net/mlx5e: Read ETS settings directly from firmware")
Signed-off-by: Alexei Lazar <alazar@nvidia.com>
Reviewed-by: Carolina Jubran <cjubran@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Link: https://patch.msgid.link/20260717075125.1244877-2-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
assoc_array_walk() masks off the bits past shortcut->skip_to_level in the
word that contains skip_to_level, gated on
round_up(sc_level, ASSOC_ARRAY_KEY_CHUNK_SIZE) > skip_to_level.
That guard is wrong in two opposite ways:
- When sc_level is word-aligned (every word after the first) round_up()
is a no-op, so the guard is sc_level > skip_to_level and never fires for
the word that holds skip_to_level. A shortcut that spans more than one
word and ends in the middle of its last word leaves that word untrimmed,
and its stale high bits leak into the dissimilarity word and can steer
the walk down the wrong descendant.
- When sc_level is unaligned (the first word) and skip_to_level sits on
the next chunk boundary, sc_level + CHUNK would exceed skip_to_level and
fire the trim with shift = skip_to_level & CHUNK_MASK == 0, which clears
the whole dissimilarity word and makes a differing shortcut compare
equal.
Use the end of the chunk that contains sc_level instead:
skip_to_level < round_down(sc_level, CHUNK) + CHUNK
For an aligned sc_level whose word holds skip_to_level this now fires (the
first bug); for an unaligned sc_level with skip_to_level on the following
boundary it does not, so shift is never 0 when the branch runs and the trim
never clears the whole word.
Fixes: 3cb989501c ("Add a generic associative array implementation.")
Assisted-by: Claude:claude-opus-4-8
Signed-off-by: Michael Bommarito <michael.bommarito@gmail.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Tested-by: Jarkko Sakkinen <jarkko@kernel.org>
Link: https://lore.kernel.org/r/20260719161505.2423935-4-michael.bommarito@gmail.com
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
keyring_get_key_chunk() loads description bytes into the index chunk low
address first, while keyring_diff_objects() numbers the first differing
bit from the low end and folds the absolute byte index into the level
without removing the inline-prefix offset the level already carries.
The two disagree on byte order and bit position, so the array can be
told two keys first differ at a bit that does not differ in the chunk
the walker uses, letting crafted descriptions collide into one node.
Load the chunk in the order keyring_diff_objects() assumes and drop the
inline-prefix length when folding the byte index into the level. This
only changes the in-memory ordering used to place keys within a keyring;
add, search and read of non-colliding keys are unaffected.
Fixes: f771fde820 ("keys: Simplify key description management")
Assisted-by: Claude:claude-opus-4-8
Signed-off-by: Michael Bommarito <michael.bommarito@gmail.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Tested-by: Jarkko Sakkinen <jarkko@kernel.org>
Link: https://lore.kernel.org/r/20260719161505.2423935-3-michael.bommarito@gmail.com
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
For description-level chunks keyring_get_key_chunk() advances the read
pointer by level * sizeof(long) past the inline prefix but only
bounds-checks the prefix, so a long enough key description is read past
its kmemdup(desc, desc_len + 1) allocation. Compute the full byte
offset and bounds-check the description against it before reading.
The walk only reaches a description-level chunk when two keys collide
through the hash, x, type and domain_tag chunks, so this is reached from
an unprivileged add_key(2) with a crafted pair of same-type keys whose
index hashes collide; KASAN reports a slab-out-of-bounds read.
Fixes: f771fde820 ("keys: Simplify key description management")
Assisted-by: Claude:claude-opus-4-8
Signed-off-by: Michael Bommarito <michael.bommarito@gmail.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Tested-by: Jarkko Sakkinen <jarkko@kernel.org>
Link: https://lore.kernel.org/r/20260719161505.2423935-2-michael.bommarito@gmail.com
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Two correctness and type-hygiene issues exist in the DCP trusted keys
implementation.
First, trusted_dcp_unseal() reads p->key_len from a user-supplied blob
without checking if it exceeds MAX_KEY_SIZE. If a crafted blob provides a
payload_len larger than 128, the subsequent do_aead_crypto() call writes
past the end of the p->key array into the adjacent p->blob buffer within
the same struct trusted_key_payload -- the caller's own input, not
unrelated kernel memory. While not exploitable, this violates strict array
bounds and triggers static analyzers. Fix this by adding a validation
check against MIN_KEY_SIZE and MAX_KEY_SIZE immediately after reading the
length, matching the checks already done in trusted_core.c.
Second, calc_blob_len() calculates a sum in size_t that truncates to
unsigned int on 64-bit platforms. Because the DCP hardware is only present
on 32-bit i.MX SoC platforms, size_t and unsigned int are functionally
equivalent in production, making this truncation harmless in practice.
Nevertheless, updating the return type to size_t (and subsequently updating
'blen' in the seal/unseal paths) resolves type-narrowing warnings and
improves overall code hygiene.
Fixes: 2e8a0f40a3 ("KEYS: trusted: Introduce NXP DCP-backed trusted keys")
Signed-off-by: Fabrice Derepas <fabrice.derepas@canonical.com>
Reviewed-by: David Gstir <david@sigma-star.at>
Reviewed-by: Richard Weinberger <richard@nod.at>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Tested-by: Jarkko Sakkinen <jarkko@kernel.org>
Link: https://lore.kernel.org/r/20260719163939.3624767-1-fabrice.derepas@canonical.com
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Commit 2a22b7ae2f ("net: pcs: xpcs: adapt Wangxun NICs for SGMII mode")
added a path in xpcs_get_state_c37_sgmii() that reads speed/duplex from
BMCR after AN completes. However, BMCR does not reflect the negotiated
result on the hardware where this has been tested:
- On RK3568 (MAC side SGMII), BMCR returns a fixed hardware reset value
- Wangxun engineer Jiawen Wu confirmed that on their side, "BMCR looks
like it only wants to be return as 0" [0]
The correct information is available in CL37_ANSGM_STS, which contains
the actual link status and negotiated speed/duplex.
This bug was previously masked by phylink core, which overrides the PCS
link state with the PHY state when a PHY is present:
/* If we have a phy, the "up" state is the union of both the
* PHY and the MAC
*/
if (phy)
link_state.link &= pl->phy_state.link;
Thus, when the link is down, the PHY's link_down state is applied on top
of whatever the PCS reports, hiding the broken PCS state reading path.
Modify xpcs_get_state_c37_sgmii() to:
1. Read link state from CL37_ANSGM_STS
2. If link is up, report speed/duplex from CL37_ANSGM_STS
3. Remove the broken BMCR reading path entirely
Also properly set state->an_complete to reflect the AN completion status,
and clear CL37_ANCMPLT_INTR when link is down to avoid stale state.
[0] https://lore.kernel.org/all/000c01dd1593$2ac0b0f0$804212d0$@trustnetic.com/
Fixes: 2a22b7ae2f ("net: pcs: xpcs: adapt Wangxun NICs for SGMII mode")
Cc: stable@vger.kernel.org
Tested-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: Coia Prant <coiaprant@gmail.com>
Tested-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20260717074324.3250043-2-coiaprant@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
esw_egress_acl_vlan_create() hardcodes num_dest=0 in its
mlx5_add_flow_rules() call. When invoked from the non-bond path
fwd_dest is NULL and num_dest=0 is correct. When invoked from
esw_acl_egress_ofld_rules_create() during a bond event, fwd_dest is
non-NULL and flow_act.action carries MLX5_FLOW_CONTEXT_ACTION_FWD_DEST,
but _mlx5_add_flow_rules() rejects a non-NULL dest pointer paired with
dest_num<=0 and returns -EINVAL. The error propagates as
"configure slave vport egress fwd, err(-22)". The passive vport's egress
ACL table ends up with its flow groups allocated but no FTEs, so
prio-tagged packets are not popped and bond failover is broken on
prio_tag_required devices.
Fix by passing fwd_dest ? 1 : 0 as num_dest to match the actual number
of destinations supplied.
Fixes: bf773dc0e6 ("net/mlx5: E-Switch, Introduce APIs to enable egress acl forward-to-vport rule")
Signed-off-by: Yael Chemla <ychemla@nvidia.com>
Reviewed-by: Cosmin Ratiu <cratiu@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/20260717073306.1242399-1-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The MCIA register can return up to 32 dwords (128 bytes) when the device
advertises the mcia_32dwords capability, but struct
mlx5_ifc_mcia_reg_bits only defines dword_0..11, leaving room for just
12 dwords (48 bytes) of data.
mlx5_query_mcia() clamps the read size to mlx5_mcia_max_bytes() and then
memcpy()s that many bytes out of the register, potentially reading past
the end of the 'out' buffer. On kernels built with FORTIFY_SOURCE this
is caught as a buffer overflow while reading the module EEPROM via
ethtool:
detected buffer overflow in memcpy
kernel BUG at lib/string_helpers.c:1048!
RIP: 0010:fortify_panic+0x13/0x20
Call Trace:
mlx5_query_mcia.isra.0+0x200/0x210 [mlx5_core]
mlx5_query_module_eeprom_by_page+0x4a/0xa0 [mlx5_core]
mlx5e_get_module_eeprom_by_page+0xbb/0x120 [mlx5_core]
eeprom_prepare_data+0xf3/0x170
ethnl_default_doit+0xf1/0x3b0
Extend the mcia_reg layout to 32 dwords.
Fixes: 271907ee2f ("net/mlx5: Query the maximum MCIA register read size from firmware")
Signed-off-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Alex Lazar <alazar@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/20260717072338.1240582-1-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Doruk Tan Ozturk says:
====================
vxlan, geneve: require CAP_NET_ADMIN in the device netns for changelink
The recent series "require CAP_NET_ADMIN in the device netns for
changelink" (8165f7ff57d9..27ccb68e7ccc) added rtnl_dev_link_net_capable()
and gated the eight IP tunnel drivers (ip_gre, ipip, ip_vti, ip6_tunnel,
ip6_gre, ip6_vti, sit, xfrm_interface). VXLAN and GENEVE share the exact
same shape but were not covered: both store the underlay netns sticky at
newlink (vxlan->net / geneve->net) and their changelink() operates on that
netns, while the generic RTM_NEWLINK path only checks CAP_NET_ADMIN against
dev_net(dev). Once such a device is created in or moved to another netns,
a caller privileged in dev_net(dev) but not in the underlay netns can
reconfigure the tunnel'"'"'s underlay.
This completes that series for the two UDP tunnel drivers that were left
out. Same helper, same placement (top of changelink, before any attribute
is parsed).
Verified on next-20260714 in QEMU with CONFIG_VXLAN=y + CONFIG_USER_NS=y:
an unprivileged user namespace holding CAP_NET_ADMIN only in a child netns
issues an IFLA_INFO_DATA changelink on a vxlan device whose underlay lives
in init_net. Before: returns 0 (reconfigures the init_net underlay).
After: returns -EPERM.
====================
Link: https://patch.msgid.link/20260716203500.70573-1-doruk@0sec.ai
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A tunnel changelink() operates on at most two netns, dev_net(dev) and
the sticky underlay netns geneve->net. They differ once the device is
created in or moved to a netns other than the one the request runs in.
The rtnl changelink path checks CAP_NET_ADMIN only against dev_net(dev),
so a caller privileged there but not in geneve->net can rewrite a geneve
device whose underlay lives in geneve->net.
geneve_changelink() applies the new configuration against geneve->net:
geneve_link_config() and the geneve_quiesce()/geneve_unquiesce() pair
reopen the underlay sockets in that netns (geneve_sock_add() uses
geneve->net), so the same reasoning as the tunnel changelink series
applies here.
Gate geneve_changelink() with rtnl_dev_link_net_capable(), at the top of
the op before any attribute is parsed, matching ipgre_changelink() and
the rest of the "require CAP_NET_ADMIN in the device netns for
changelink" series.
Found by 0sec automated security-research tooling (https://0sec.ai).
Fixes: 5b861f6baa ("geneve: add rtnl changelink support")
Cc: stable@vger.kernel.org
Signed-off-by: Doruk Tan Ozturk <doruk@0sec.ai>
Reviewed-by: Fernando Fernandez Mancera <fmancera@suse.de>
Link: https://patch.msgid.link/20260716203500.70573-3-doruk@0sec.ai
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A tunnel changelink() operates on at most two netns, dev_net(dev) and
the sticky underlay netns vxlan->net. They differ once the device is
created in or moved to a netns other than the one the request runs in.
The rtnl changelink path checks CAP_NET_ADMIN only against dev_net(dev),
so a caller privileged there but not in vxlan->net can rewrite a vxlan
device whose underlay lives in vxlan->net.
vxlan_changelink() validates and applies the new configuration against
vxlan->net (vxlan_config_validate(vxlan->net, ...)) and can reopen the
underlay socket in that netns, so the same reasoning as the tunnel
changelink series applies here.
Gate vxlan_changelink() with rtnl_dev_link_net_capable(), at the top of
the op before any attribute is parsed, matching ipgre_changelink() and
the rest of the "require CAP_NET_ADMIN in the device netns for
changelink" series.
Found by 0sec automated security-research tooling (https://0sec.ai).
Fixes: 8bcdc4f3a2 ("vxlan: add changelink support")
Cc: stable@vger.kernel.org
Signed-off-by: Doruk Tan Ozturk <doruk@0sec.ai>
Reviewed-by: Fernando Fernandez Mancera <fmancera@suse.de>
Link: https://patch.msgid.link/20260716203500.70573-2-doruk@0sec.ai
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
llsec_do_decrypt_auth() computes the associated-data length for the
AEAD request as
assoclen += datalen - authlen;
where datalen is the number of bytes after the MAC header and authlen
(4, 8 or 16) is the length of the authentication tag. Nothing verifies
that the frame actually carries at least authlen payload bytes. A
secured frame whose payload is shorter than the tag makes
datalen - authlen negative; assoclen is then passed to
aead_request_set_ad() as an unsigned value close to 4 GiB, so
crypto_aead_decrypt() walks far off the end of the scatterlist that
only spans the real frame.
The frame is fully attacker-controlled and reaches this path from any
IEEE 802.15.4 peer in radio range. Reject frames whose payload is
shorter than the authentication tag before the subtraction.
Dynamically reproduced on a KASAN kernel as a general-protection-fault
in the AEAD scatterwalk, and the fix confirmed.
Fixes: 4c14a2fb5d ("mac802154: add llsec decryption method")
Cc: stable@vger.kernel.org
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Doruk Tan Ozturk <doruk@0sec.ai>
Link: https://patch.msgid.link/20260716193423.32498-1-doruk@0sec.ai
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
raw_v4_match() is a lockless match helper under sk_for_each_rcu(). It
still reads inet->inet_daddr, inet->inet_rcv_saddr and
sk->sk_bound_dev_if with plain loads while bind, connect and
bind-to-device paths can update the same match fields concurrently.
Annotate only those mutable match fields in raw_v4_match(), and do so
at the point of use instead of hoisting the bound-device read before
the earlier short-circuit tests.
Also annotate the raw bind writer and the shared IPv4 datagram connect
writer used by raw sockets, so the address fields updated on bind and
connect match explicit WRITE_ONCE() updates.
This version intentionally leaves the shared disconnect-side IPv4
writers to follow-up cleanup and limits the writer changes here to the
raw bind path and the datagram connect path directly exercised by raw
sockets.
Fixes: 0daf07e527 ("raw: convert raw sockets to RCU")
Signed-off-by: Runyu Xiao <runyu.xiao@seu.edu.cn>
Link: https://patch.msgid.link/20260716142958.3064224-1-runyu.xiao@seu.edu.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
QRTR keeps its entire port and node state in module-global variables
that are not partitioned per network namespace: qrtr_local_nid is a
single global node id (always 1) and qrtr_ports is a single global
xarray. qrtr_port_lookup() and qrtr_local_enqueue() operate on that
global state with no network-namespace check, and qrtr_create() places
no restriction on the namespace a socket is created in.
As a result an unprivileged process that creates an AF_QIPCRTR socket
in a separate network namespace, e.g. via
unshare(CLONE_NEWUSER | CLONE_NEWNET), can send QRTR datagrams -
including control-plane messages such as QRTR_TYPE_NEW_SERVER - to QRTR
sockets owned by another namespace, and vice versa. The receiving
socket sees such a message as coming from node id 1, indistinguishable
from a legitimate local client, breaking the isolation that network
namespaces are expected to provide.
QRTR is a transport to global hardware endpoints (the modem and other
remote processors) and has no per-namespace semantics; its in-kernel
name service already creates its socket in init_net only. Confine the
socket family to the initial network namespace, as other
non-namespace-aware socket families do (see llc_ui_create() and the
ieee802154 socket code).
Fixes: bdabad3e36 ("net: Add Qualcomm IPC router")
Signed-off-by: Aldo Ariel Panzardo <qwe.aldo@gmail.com>
Link: https://patch.msgid.link/20260716154319.3297699-1-qwe.aldo@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
ALU32 operations write a 32-bit result and leave the upper 32 bits of
the BPF register zero. The LoongArch JIT sign-extends the result of
signed ALU32 BPF_DIV and BPF_MOD (off=1), so a negative 32-bit quotient
or remainder leaves bits 63:32 set in JITted code while the verifier
and interpreter model those bits as zero.
Keep sign-extension on the operands, which signed divide needs, and
zero-extend the ALU32 result after the divide or modulo instruction,
matching the unsigned ALU32 div/mod paths and every other ALU32
operation in this JIT.
Fixes: 2425c9e002 ("LoongArch: BPF: Support signed div instructions")
Fixes: 7b6b13d329 ("LoongArch: BPF: Support signed mod instructions")
Assisted-by: Claude:claude-opus-4-8
Acked-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Tested-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Signed-off-by: Nicholas Dudar <main.kalliope@gmail.com>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
When entering KDB via a breakpoint and then performing single-step
debugging, an oops is triggered. Now during single-step debugging,
kdb_local() expects the reason to be KDB_REASON_SSTEP, but it is
actually KDB_REASON_OOPS. In kdb_stub(), when determining the reason,
the ex_vector for single-step should be 0, as already implemented on
other architectures such as arm64 and riscv.
Before the patch:
[112]kdb> ss
Entering kdb (current=0x900020009f520000, pid 10661) on
processor 112 Oops: (null)
due to oops @ 0x90000000005b57a4
Cc: stable@vger.kernel.org
Signed-off-by: Haoran Jiang <jianghaoran@kylinos.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
When searching the loaded segments for the "kexec" command line marker,
the kexec_load(2) path (file_mode == 0) passes the user-space segment
buffer straight to strncmp() through a bogus (char __user *) cast. This
dereferences a user pointer in kernel context, which is wrong and is
flagged by sparse:
arch/loongarch/kernel/machine_kexec.c:84:51: sparse: incorrect type in
argument 2 (different address spaces) @@ expected char const * @@ got
char [noderef] __user *
Here copy the marker-sized prefix of each segment into a small on-stack
buffer with copy_from_user() before comparing, and skip segments that
fault. The subsequent copy_from_user() that stages the full command line
into the safe area is left unchanged.
Cc: stable@vger.kernel.org
Fixes: 4a03b2ac06 ("LoongArch: Add kexec support")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202605051639.aEPioXdD-lkp@intel.com/
Co-developed-by: Kexin Liu <liukexin@kylinos.cn>
Signed-off-by: Kexin Liu <liukexin@kylinos.cn>
Signed-off-by: George Guo <guodongtai@kylinos.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Currently, the LoongArch CPU topology initialization code calculates
each core's package ID by dividing its physical ID by loongson_sysconf.
cores_per_package. This relies on the assumption that cores_per_package
counts in the same domain as physical IDs.
On Loongson-3B6000 (XB612B0V_1.2), cores_per_package matches the visible
core count -- 24 in this case. However, the physical IDs range from 0 to
31 in a noncontinuous fashion:
$ cat /proc/cpuinfo | grep -i -F 'global_id'
global_id : 0
global_id : 1
global_id : 4
global_id : 5
global_id : 6
global_id : 7
global_id : 8
global_id : 9
global_id : 10
global_id : 11
global_id : 14
global_id : 15
global_id : 16
global_id : 17
global_id : 20
global_id : 21
global_id : 22
global_id : 23
global_id : 26
global_id : 27
global_id : 28
global_id : 29
global_id : 30
global_id : 31
Retrieve the exact package ID from ACPI PPTT when available, in the same
style as retrieving the core ID and thread ID in parse_acpi_topology().
Use this information in loongson_init_secondary() when the PPTT readout
is successful. The original division logic is kept as a fallback.
Meanwhile, since some existing code paths like loongson3_cpufreq expect
a continuous integer sequence of package IDs in [0, MAX_PACKAGES) when
retrieving from cpu_data[], here we also canonicalize the package ID to
be filled in parse_acpi_topology() to meet such an expectation.
Cc: stable@vger.kernel.org
Tested-by: Mingcong Bai <jeffbai@aosc.io>
Co-developed-by: Xi Ruoyao <xry111@xry111.site>
Signed-off-by: Xi Ruoyao <xry111@xry111.site>
Signed-off-by: Rong Bao <rong.bao@csmantle.top>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
When enabling both CONFIG_MEM_ALLOC_PROFILING=y and
CONFIG_MEM_ALLOC_PROFILING_ENABLED_BY_DEFAULT=y, then diabling memory
profiling by adding the boot parameter 'sysctl.vm.mem_profiling=0' will
cause the kernel failed to boot.
After analysis, this is because jump_label_init() must be called before
parse_early_param(), the early param handlers may modify static keys by
static_branch_enable/disable().
Fix this by moving jump_label_init() to before parse_early_param(). The
solution is similar to other architectures.
Cc: <stable@vger.kernel.org>
Signed-off-by: Kanglong Wang <wangkanglong@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
In some assembly files there are some instructions that only valid for
64BIT, but those files can be compiled for 32BIT and cause build errors.
So, replace those instructions with macros:
li.d --> LONG_LI (li.w or li.d), addi.d --> PTR_ADDI (addi.w or addi.d).
BTW, Re-tab the indention in the assembly files for alignment.
Cc: stable@vger.kernel.org # 6.19+
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
THREAD_INFO_IN_TASK increase the size of task_struct, which casuses a
build error for the 32BIT kernel if RANDSTRUCT is enabled. So increase
TASK_STRUCT_OFFSET as big as possible (2040), but can still be aligned
and be fit in the addi.w instruction.
Cc: stable@vger.kernel.org
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
rss_indir_user and rss_hkey_user are allocated and filled in
__set_rss_rxfh() when the user configures RSS via ethtool, but
nothing ever reads them. hinic_get_rxfh() fetches the state from
the device, and the hardware is programmed from the original
indir/key arguments. These buffers only leaked on driver unload.
Drop the unused allocations, memcpys, and struct fields.
Fixes: 4fdc51bb4e ("hinic: add support for rss parameters with ethtool")
Signed-off-by: Chenguang Zhao <zhaochenguang@kylinos.cn>
Reviewed-by: Joe Damato <joe@dama.to>
Link: https://patch.msgid.link/20260722025353.328179-1-chenguang.zhao@linux.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Sven Schnelle says:
====================
Add missing facility check to ptp_s390 driver
This patchset adds a missing facility check and a check that the 'query
physical clock' (PTFF QPT) function is actually available. If it's not
present, no qpt ptp device will be registered. In order to use ptff_query()
in a module, the first patch adds a EXPORT_SYMBOL() to export
ptff_function_mask.
====================
Link: https://patch.msgid.link/20260714130342.1971700-1-svens@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Only register the physical clock when facility 28 is installed
and PTFF QAF returns that PTFF QPT is available.
Fixes: 2d7de7a301 ("s390/time: Add PtP driver")
Signed-off-by: Sven Schnelle <svens@linux.ibm.com>
Cc: stable@kernel.org
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Link: https://patch.msgid.link/20260714130342.1971700-3-svens@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Export the ptff_function_mask to make ptff_query() usable in modules.
Signed-off-by: Sven Schnelle <svens@linux.ibm.com>
Acked-by: Heiko Carstens <hca@linux.ibm.com>
Link: https://patch.msgid.link/20260714130342.1971700-2-svens@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The stmmac driver based on Synopsys' dwmac IP is used in a very wide
variety of SoCs and is currently very actively used and contributed to.
It has been orphaned in January 2025 after the previous maintainers
became inactive, but Russell King was providing very valuable reviews
and fixes for the driver at that point.
Now we're seeing more and more activity on the driver, but are lacking
people to test and review contributions to both glue drivers as well as
core stmmac code.
I have access to some variety of stmmac-based platforms such as socfpga
CycloneV, imx8mp, some Allwinner SoCs and stm32mp1xx boards that I can
run regression tests on, and I'm offering to step-up as a maintainer for
driver, for the time being at least.
Let's hope other people will eventually join this effort.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20260722142125.1767689-1-maxime.chevallier@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
pppoe_sendmsg() saves a pointer to the PPPoE header before calling
dev_hard_header(). Device header callbacks are allowed to reallocate the
skb head, invalidating pointers into it.
This can happen when a send is blocked in copy_from_user() while the first
non-Ethernet port is added to an empty team device. The team's delegated
GRE header callback then expands the skb head. PPPoE subsequently writes
six bytes through the stale pointer into the freed head.
Reload the PPPoE header through the skb's network-header offset after
device header creation. pskb_expand_head() updates that offset when it
relocates the head.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable@vger.kernel.org
Signed-off-by: Asim Viladi Oglu Manizada <manizada@pm.me>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20260722093814.3017176-1-manizada@pm.me
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Several fields in struct ppp can be read or updated concurrently
from multiple CPUs without synchronization, causing data races:
1. ppp->mru is read concurrently in ppp_receive_nonmp_frame() while
being updated via PPPIOCSMRU ioctl. Protect ppp->mru updates in
PPPIOCSMRU with ppp_recv_lock(ppp).
2. PPPIOCGFLAGS reads ppp->flags, ppp->xstate, and ppp->rstate
unlocked. Wrap the read in ppp_lock(ppp) to get a consistent
snapshot.
3. ppp->debug is updated via PPPIOCSDEBUG and read concurrently on
fast paths. Annotate reads with READ_ONCE() and writes with
WRITE_ONCE().
4. ppp->last_xmit and ppp->last_recv are updated on TX/RX data paths
and read via PPPIOCGIDLE32 / PPPIOCGIDLE64 ioctls. Annotate with
WRITE_ONCE() / READ_ONCE() and use max() to handle jiffies
subtraction.
5. ppp->npmode[] is updated via PPPIOCSNPMODE and read on TX/RX
paths. Annotate with WRITE_ONCE() / READ_ONCE().
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Qingfang Deng <qingfang.deng@linux.dev>
Link: https://patch.msgid.link/20260722101605.2868548-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When Linux forwards a packet and needs to generate an ICMP error,
icmp_route_lookup() performs a reverse-path relookup. For non-local
destinations, it performs a decoy lookup to find the expected egress
interface (rt2->dst.dev) before validating the path with ip_route_input().
Currently, the decoy flow structure (fl4_2) only sets .daddr = fl4_dec.saddr,
leaving .saddr, .flowi4_dscp, .flowi4_proto, .flowi4_mark, .flowi4_oif,
.fl4_sport, .fl4_dport, and .flowi4_uid zeroed out.
When policy routing rules (such as ip rule add from $SRC lookup 100, or
dscp/fwmark/ipproto/port rules, or VRF bindings) are configured:
1. The decoy lookup fails to match the policy rule because saddr and other
key flow selectors are missing in fl4_2.
2. It resolves a route using the default table instead, returning an incorrect
egress netdev.
3. Passing the wrong netdev to ip_route_input() causes strict reverse-path
filtering (rp_filter=1) to fail, logging false-positive "martian source"
warnings and causing the relookup to fail.
Fix this by initializing fl4_2 from fl4_dec and:
- Swapping source/destination IP addresses.
- Swapping L4 ports for transport protocols with ports (TCP, UDP, SCTP, DCCP)
so port-based policy routing matches correctly. Non-port protocols (such as
ICMP or GRE) leave the flowi_uli union fields intact to prevent corruption.
- Setting .flowi4_oif = l3mdev_master_ifindex(route_lookup_dev) to ensure
VRF routing tables are respected.
- Setting .flowi4_flags |= FLOWI_FLAG_ANYSRC to allow output route lookups
for non-local source IP addresses.
- Using __ip_route_output_key() instead of ip_route_output_key() for fl4_2
so that raw FIB routing is used without triggering spurious XFRM policy
lookups on the decoy flow (the actual XFRM lookup is performed later using
fl4_dec).
Fixes: 415b3334a2 ("icmp: Fix regression in nexthop resolution during replies.")
Reported-by: Muhammad Ziad <muhzi100@gmail.com>
Closes: https://lore.kernel.org/netdev/CAOAwikA60AYKdFr_UDLyja3oU4hqyAE7uFZWqum5uRdaQsgRYg@mail.gmail.com/
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://patch.msgid.link/20260722104236.2938082-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When an AMT device is removed, pending delayed works can still access
the freed amt_dev structure, which may result in kernel crashes or
memory corruption.
amt_dev_stop() cancels req_wq and discovery_wq with
cancel_delayed_work_sync(), but these works can be scheduled again
from event_wq after the cancellation. This allows delayed works to
access the freed amt_dev structure after the netdev has been released.
The following is a simple race scenario:
CPU0 CPU1
amt_dev_stop()
cancel_delayed_work_sync()
amt_event_work()
mod_delayed_work(req_wq)
free netdev
req_wq accesses freed amt_dev
Use disable_delayed_work_sync() in amt_dev_stop() to prevent req_wq and
discovery_wq from being queued again and wait for running work items
to complete.
The delayed works are disabled after initialization in
amt_newlink() and enabled only when the device is successfully opened.
This keeps the delayed work lifecycle synchronized with the lifetime
of the AMT device.
Fixes: cbc21dc1cf ("amt: add data plane of amt interface")
Cc: stable@vger.kernel.org
Signed-off-by: Shihuang Liu <shlomojune6@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Taehee Yoo <ap420073@gmail.com>
Link: https://patch.msgid.link/20260722113919.7723-1-shlomojune6@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The MCTP serial receive state machine reads a frame length byte in
mctp_serial_push_header() case 2 and validates it upper-bound-only:
if (c > MCTP_SERIAL_FRAME_MTU) {
dev->rxstate = STATE_ERR;
} else {
dev->rxlen = c;
dev->rxpos = 0;
dev->rxstate = STATE_DATA;
...
}
A length of zero passes this check, so rxlen is set to 0 and the state
machine advances to STATE_DATA. In mctp_serial_push() STATE_DATA, the
incoming byte is stored and rxpos incremented before the terminator is
tested:
dev->rxbuf[dev->rxpos] = c;
dev->rxpos++;
dev->rxstate = STATE_DATA;
if (dev->rxpos == dev->rxlen) {
dev->rxpos = 0;
dev->rxstate = STATE_TRAILER;
}
With rxlen == 0 the "rxpos == rxlen" terminator can never fire (rxpos is
already 1 on the first data byte), so subsequent bytes are written past
the end of the fixed 74-byte rxbuf, which is the last member of the
netdev private area. Every following data byte is an attacker-controlled
1-byte out-of-bounds heap write, and the overflow continues until a
frame (0x7e) or escape byte resets the parser -- effectively unbounded.
Reaching this requires CAP_NET_ADMIN to attach the N_MCTP line
discipline and bring the resulting mctpserialN netdev up, after which
the bytes arrive via the tty receive path.
Route a zero-length frame straight to STATE_TRAILER instead of
STATE_DATA. The trailer/framing bytes are still consumed, and the frame
resolves to a zero-length skb that the MCTP core rejects; the parser
never enters STATE_DATA with rxlen == 0, so the out-of-bounds write can
no longer occur.
KASAN, on a frame of 0x7e 0x01 0x00 followed by data bytes (before this
change):
UBSAN: array-index-out-of-bounds in drivers/net/mctp/mctp-serial.c:370
index 74 is out of range for type 'u8 [74]'
BUG: KASAN: slab-out-of-bounds in mctp_serial_tty_receive_buf
Write of size 1 at addr ... by task kworker/u16:0
mctp_serial_tty_receive_buf
tty_ldisc_receive_buf
flush_to_ldisc
Allocated by task 152:
alloc_netdev_mqs
mctp_serial_open
v2: route zero-length frames to STATE_TRAILER instead of STATE_ERR so
the trailer/framing bytes are still consumed (Jeremy Kerr).
Found by 0sec automated security-research tooling (https://0sec.ai).
Fixes: a0c2ccd9b5 ("mctp: Add MCTP-over-serial transport binding")
Cc: stable@vger.kernel.org
Suggested-by: Jeremy Kerr <jk@codeconstruct.com.au>
Assisted-by: 0sec:multi-model
Signed-off-by: Doruk Tan Ozturk <doruk@0sec.ai>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20260715082021.46315-1-doruk@0sec.ai
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
When MCAM entries are allocated for a VF netdev via the devlink
mcam_count parameter, only OTX2_FLAG_NTUPLE_SUPPORT was set. That
enabled ethtool ntuple filters but not tc flower offload. Also set
OTX2_FLAG_TC_FLOWER_SUPPORT when entries are successfully allocated.
Fixes: 2da4894327 ("octeontx2-pf: devlink params support to set mcam entry count")
Signed-off-by: Suman Ghosh <sumang@marvell.com>
Signed-off-by: Ratheesh Kannoth <rkannoth@marvell.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20260715052007.2099851-1-rkannoth@marvell.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Commit f0914b8436 ("mpls: Hold dev refcnt for mpls_nh.") added
change_nexthops() loop to call netdev_put() for the nexthop devices
before freeing mpls_route.
Then, mpls_nh_build_multi() was also changed to avoid iterating
uninitialised nexthops in mpls_rt_free_rcu().
However, setting rt->rt_nhn to 0 at the entry of mpls_nh_build_multi()
makes the following change_nexthops() no-op.
Let's set rt->rt_nhn just before returning from mpls_nh_build_multi().
Fixes: f0914b8436 ("mpls: Hold dev refcnt for mpls_nh.")
Reported-by: Anthony Doeraene <anthony.doeraene@uclouvain.be>
Closes: https://lore.kernel.org/netdev/036a0c95-f5d4-46ab-88e7-1eab567d7a84@uclouvain.be/
Signed-off-by: Kuniyuki Iwashima <kuniyu@google.com>
Link: https://patch.msgid.link/20260716170609.804629-1-kuniyu@google.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Before commit 00d066a4d4 ("netdev_features: convert NETIF_F_LLTX to
dev->lltx"), NETIF_F_LLTX was set unconditionally in both
__gre_tunnel_init() and ip6gre_tnl_init_features() alongside
GRE_FEATURES:
dev->features |= GRE_FEATURES | NETIF_F_LLTX;
When that commit converted NETIF_F_LLTX to the dev->lltx flag, it
placed 'dev->lltx = true' after the SEQ/CSUM early returns instead
of before them. This causes GRE/GRETAP/ip6gre tunnels with SEQ or
CSUM+encap to lose lockless TX, reintroducing _xmit_lock acquisition
around their ndo_start_xmit. Since GRE xmit re-enters the stack via
ip_tunnel_xmit(), holding _xmit_lock risks ABBA deadlock with the
underlay device.
CPU0 CPU1
---- ----
lock(&qdisc_xmit_lock_key#6);
lock(&qdisc_xmit_lock_key#3);
lock(&qdisc_xmit_lock_key#6);
lock(&qdisc_xmit_lock_key#3);
Fix by moving dev->lltx = true before the early returns in both
functions, restoring the original unconditional behavior.
Fixes: 00d066a4d4 ("netdev_features: convert NETIF_F_LLTX to dev->lltx")
Signed-off-by: Yun Zhou <yun.zhou@windriver.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Link: https://patch.msgid.link/20260713150945.1779628-1-yun.zhou@windriver.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
When tipc_sk_create() fails to insert the new socket (tipc_sk_insert()
returns non-zero), its error path frees the sk with sk_free() but leaves
sock->sk pointing at the freed object:
if (tipc_sk_insert(tsk)) {
sk_free(sk);
pr_warn("Socket create failed; port number exhausted\n");
return -EINVAL;
}
This is harmless for plain socket(): the syscall layer clears sock->ops
before releasing, so tipc_release() is never called. It is not harmless
on the accept() path. tipc_accept() creates the pre-allocated child
socket with tipc_sk_create(net, new_sock, 0, kern); on failure it leaves
new_sock->sk dangling and new_sock->ops non-NULL, and do_accept() then
fput()s the new file, so __sock_release() -> tipc_release() runs
lock_sock(new_sock->sk) on the freed sk -- a use-after-free write of the
sk_lock spinlock.
tipc_release() already guards this exact "failed accept() releases a
pre-allocated child" case with "if (sk == NULL) return 0;", but the
guard is bypassed because tipc_sk_create() left sock->sk non-NULL
(dangling) rather than NULL.
Clear sock->sk on the failed-insert path so the existing tipc_release()
NULL check fires and the use-after-free is avoided.
The tipc_sk_insert() failure is reached when the per-netns socket
rhashtable hits its max_size (tsk_rht_params.max_size = 1048576, ~2M
elements) -- i.e. once a netns holds ~2M TIPC sockets every insert
returns -E2BIG.
BUG: KASAN: slab-use-after-free in lock_sock_nested (net/core/sock.c:3839)
Write of size 8 at addr ffff8880047cdc38 by task init/1
lock_sock_nested (net/core/sock.c:3839)
tipc_release (net/tipc/socket.c:638)
__sock_release (net/socket.c:710)
sock_close (net/socket.c:1501)
__fput (fs/file_table.c:512)
Allocated by task 1:
sk_alloc (net/core/sock.c:2308)
tipc_sk_create (net/tipc/socket.c:487)
tipc_accept (net/tipc/socket.c:2744)
do_accept (net/socket.c:2034)
Freed by task 1:
__sk_destruct (net/core/sock.c:2391)
tipc_sk_create (net/tipc/socket.c:504)
tipc_accept (net/tipc/socket.c:2744)
do_accept (net/socket.c:2034)
Fixes: 00aff3590f ("net: tipc: fix possible refcount leak in tipc_sk_create()")
Cc: stable@vger.kernel.org
Reviewed-by: Tung Nguyen <tung.quang.nguyen@est.tech>
Reviewed-by: Breno Leitao <leitao@debian.org>
Signed-off-by: Daehyeon Ko <4ncienth@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20260714131939.1255974-1-4ncienth@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
stmmac_mac_link_down() clears the MAC's transmit and receive enable bits.
stmmac_mac_link_up() is expected to set them again through
stmmac_mac_set(..., true), but it first switches on the negotiated speed
and returns early for a speed the switch does not list. The MAC is then
left gated off.
The speed selection is split into three switches, keyed on the interface.
The generic branch -- taken for everything that is neither USXGMII nor
XLGMII, so including PHY_INTERFACE_MODE_10GBASER -- lists only SPEED_2500,
SPEED_1000, SPEED_100 and SPEED_10.
MGBE on Tegra234 runs 10GBASE-R into an Aquantia AQR113C. That PHY does
rate matching, so phylink_link_up() replaces the media speed with the
MAC-side interface speed before calling into the MAC:
case RATE_MATCH_PAUSE:
speed = phylink_interface_max_speed(link_state.interface);
duplex = DUPLEX_FULL;
The driver is therefore called as
stmmac_mac_link_up(interface=10GBASER, speed=10000, duplex=1)
which falls through to "default: return;". The interface stops passing
traffic after the first link flap.
The failure is easy to misread. The link still comes up, because the PHY
is polled over MDIO and needs no MAC, so the interface reports carrier 1
at the media speed. The DMA is untouched, so its start bits stay set and
descriptors are still consumed. Only the MAC itself is gated off: the
receiver counts nothing (mmc_rx_framecount_gb stops advancing, RE is 0)
and nothing reaches the wire (TE is 0). The interface survives boot only
because stmmac_hw_setup(), called from ndo_open, enables the MAC
unconditionally -- so the problem appears only once the cable has been
unplugged and plugged back in, and "ip link set dev <ethX> down && ip
link set dev <ethX> up" appears to fix it.
The interface is not what the speed bits depend on: with the single
exception of 2.5G, which is selected through the XGMII block on USXGMII
and through the regular speed bits otherwise, each speed maps to one
field of struct mac_link. The per-interface switches are speed
validation, and phylink already validates the speed against
priv->hw->link.caps. So collapse the three switches into one keyed on the
speed alone, keeping the interface test only for the 2.5G case. This
covers 10G on 10GBASE-R, and equally 5G, and 1G/100/10 on USXGMII, all of
which hit "default: return;" today.
A core that does not support a speed leaves the corresponding mac_link
field at 0, and phylink will not offer it that speed in the first place.
For dwxgmac2 at 10G, link.xgmii.speed10000 is XGMAC_CONFIG_SS_10000,
which is 0 and is the correct speed selection for a 10GBASE-R MAC: ctrl
then equals old_ctrl, the register write is skipped, and execution
reaches stmmac_mac_set(..., true).
Log an error in the default case, since a speed with no entry here leaves
the MAC disabled and the symptom does not point at the cause.
Fixes: d8ca113724 ("net: stmmac: tegra: Add MGBE support")
Suggested-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: vadik likholetov <vadikas@gmail.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20260713074911.30090-1-vadikas@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Commit 319c151747 ("epoll: take epitem list out of struct file")
intentionally removed temporary file references from the reverse path
check list. At the time, both epitems and their files were freed after
an RCU grace period, so unlist_file() could obtain file->f_lock through
an epitem while clear_tfile_check_list() held rcu_read_lock().
Commit 0ede61d858 ("file: convert to SLAB_TYPESAFE_BY_RCU") made
struct file SLAB_TYPESAFE_BY_RCU and removed its RCU-delayed freeing.
RCU still protects the epitem, but no longer keeps the referenced file
from being freed and reused. A concurrent close can therefore make
unlist_file() lock or unlock f_lock in a recycled file object.
This violates the documented SLAB_TYPESAFE_BY_RCU rule requiring a
reference before acquiring an object's lock. The race was reproduced,
causing a wild unlock of f_lock in a recycled file and breaking its
mutual exclusion.
Add ->file to epitems_head to remember the pinned file independently of
->epitems. A concurrent EPOLL_CTL_DEL can empty ->epitems before the head
is unlisted, leaving no epi->ffd.file from which to drop the reference.
In list_file(), acquire the reference before adding the head to the
check list. The caller either owns a reference or holds the ep->mtx for
the epitem leading to the file. In the latter case, file_ref_get() can
fail after the last reference is dropped, but eventpoll_release_file()
must acquire the same mutex before the file can be freed. The dying leaf
can be skipped because removing links cannot increase the reverse path
count.
In unlist_file(), epnested_mutex excludes another list_file() or
unlist_file(), while head->next prevents a concurrent EPOLL_CTL_DEL from
freeing the head. Save head->file locally, clear it with head->next
under f_lock, and drop the reference after the RCU-protected operation.
Christian Brauner <brauner@kernel.org> quotes:
> SLAB_TYPESAFE_BY_RCU allows a slab slot to be reused while an RCU reader
> still holds its old address. Once that address contains a new live
> struct file, KASAN sees valid, unpoisoned memory and cannot distinguish
> the stale object identity. CONFIG_DEBUG_SPINLOCK exposes the failure
> instead.
>
> The failing interleaving is:
>
> CPU0: nested EPOLL_CTL_ADD CPU1: close/open churn
> ------------------------------------ ---------------------------------
> p = hlist_first_rcu(&head->epitems)
> epi = container_of(p, ...)
> close(victim)
> __fput()
> eventpoll_release_file()
> file_free(victim)
> // the slot is free; f_lock remains
> spin_lock(&epi->ffd.file->f_lock)
> open() reuses the slot as new_file
> spin_lock_init(&new_file->f_lock)
> spin_unlock(&epi->ffd.file->f_lock) // wild unlock of new_file's lock
>
> CONFIG_DEBUG_SPINLOCK reports:
>
> BUG: spinlock already unlocked on CPU#0, poc_unlist/150
> lock: 0xffff8880067fb200, .magic: dead4ead, .owner: <none>/-1, .owner_cpu: -1
> CPU: 0 UID: 1000 PID: 150 Comm: poc_unlist Not tainted 7.2.0-rc3-dirty #22 PREEMPTLAZY
> Hardware name: QEMU Ubuntu 24.04 PC v2 (i440FX + PIIX, arch_caps fix, 1996), BIOS 1.16.3-debian-1.16.3-2 04/01/2014
> Call Trace:
> <TASK>
> dump_stack_lvl+0x64/0x80
> do_raw_spin_unlock+0x75/0xb0
> _raw_spin_unlock+0xe/0x30
> clear_tfile_check_list+0x88/0xe0
> do_epoll_ctl_file+0x519/0xcf0
> ? __pfx_ep_ptable_queue_proc+0x10/0x10
> do_epoll_ctl+0x8f/0x100
> __x64_sys_epoll_ctl+0x6f/0xa0
> do_syscall_64+0xdc/0x520
> ? srso_alias_return_thunk+0x5/0xfbef5
> entry_SYSCALL_64_after_hwframe+0x76/0x7e
> RIP: 0033:0x42034e
> Code: 48 c7 c1 b8 ff ff ff f7 d8 64 89 01 48 83 c8 ff c3 66 2e 0f 1f 84 00 00 00 00 00 90 f3 0f 1e fa 49 89 ca b8 e9 00 00 00 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 b8 ff ff ff f7 d8 64 89 01 48
> RSP: 002b:00007a657ff3c198 EFLAGS: 00000202 ORIG_RAX: 00000000000000e9
> RAX: ffffffffffffffda RBX: 00007a657ff3ccdc RCX: 000000000042034e
> RDX: 0000000000000003 RSI: 0000000000000001 RDI: 0000000000000004
> RBP: 00007a657ff3c2f0 R08: 0000000000000000 R09: 00007a657ff3c6c0
> R10: 00007a657ff3c1a4 R11: 0000000000000202 R12: 00007a657ff3c6c0
> R13: ffffffffffffffb8 R14: 000000000000000d R15: 00007fffb7de0210
> </TASK>
> ------------[ cut here ]------------
>
> unlist_file() does not appear as a separate frame because it was inlined
> into clear_tfile_check_list(). This report was obtained with mdelay()
> instrumentation immediately before spin_lock() and spin_unlock() in
> unlist_file() to widen the two race windows.
>
> More importantly, this is a wild unlock. The stale unlock can target
> f_lock of a different live file and invalidate mutual exclusion for
> state protected by that lock. Turning this into a reliable exploit
> would require precise scheduling and same-slot reuse and is likely
> difficult, but the primitive is potentially exploitable.
Reported-by: Qi Tang <tpluszz77@gmail.com>
Reported-by: Junxi Qian <qjx1298677004@gmail.com>
Fixes: 0ede61d858 ("file: convert to SLAB_TYPESAFE_BY_RCU")
Cc: stable@vger.kernel.org
Signed-off-by: Guidong Han <2045gemini@gmail.com>
Link: https://patch.msgid.link/20260718104406.27897-1-2045gemini@gmail.com
Signed-off-by: Christian Brauner (Amutable) <brauner@kernel.org>
Nazim Amirul says:
====================
net: stmmac: L3/L4 filter bug fixes
This series fixes three bugs in the stmmac L3/L4 TC flower filter
implementation for the XGMAC2 core. All three patches target net.
The L3/L4 filter match count statistics patch (originally patch 4/4)
has been split out and will be sent separately against net-next per
Andrew Lunn's review of v1.
Patch 1 fixes a register corruption bug in the L4 filter port configuration.
The XGMAC_L4_ADDR register holds both source and destination port match
values in a single register. The original code overwrites the entire register
when setting either field, silently erasing the other. This is fixed by
using a read-modify-write sequence.
Patch 2 fixes the basic flow match parser to properly reject unsupported
offload requests with -EOPNOTSUPP instead of silently accepting them.
Unsupported cases include partial protocol masks, non-IPv4 network proto,
and non-TCP/UDP transport proto. Extack messages are now included so users
know exactly which part of the match is unsupported. The -EOPNOTSUPP is
also now returned directly instead of using break, which was silently
discarding the error on FLOW_CLS_REPLACE operations.
Patch 3 fixes a stale action bug on filter deletion. When a filter entry
with a drop action is deleted, the action field was not reset, causing
it to persist and potentially affect subsequent filter configurations.
All three patches fix the original L3/L4 filter implementation introduced in
425eabddaf ("net: stmmac: Implement L3/L4 Filters using TC Flower").
====================
Link: https://patch.msgid.link/20260714023716.29865-1-muhammad.nazim.amirul.nazle.asmade@altera.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
When deleting an L3/L4 flower filter entry, the action field is not
reset. If a filter was previously configured with a drop action, that
action may persist and affect subsequent filter configurations
unintentionally.
Clear the action field when the filter entry is deleted.
Fixes: 425eabddaf ("net: stmmac: Implement L3/L4 Filters using TC Flower")
Signed-off-by: Rohan G Thomas <rohan.g.thomas@altera.com>
Signed-off-by: Nazim Amirul <muhammad.nazim.amirul.nazle.asmade@altera.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20260714023716.29865-5-muhammad.nazim.amirul.nazle.asmade@altera.com
Reviewed-by: Jakub Raczynski <j.raczynski@samsung.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The basic flow parser in tc_add_basic_flow() does not validate match
keys before proceeding. Unsupported offload configurations such as
partial protocol masks, non-IPv4 network proto, or non-TCP/UDP transport
proto are silently accepted instead of returning -EOPNOTSUPP.
Add validation to return -EOPNOTSUPP early for:
- No network or transport proto present in the key
- Partial protocol mask (only full mask supported)
- Network proto is not IPv4
- Transport proto is not TCP or UDP
Each rejection includes an extack message so the user knows which part
of the match is unsupported.
Also propagate -EOPNOTSUPP from tc_add_basic_flow() in tc_add_flow()
by returning it directly rather than using break. The break was silently
discarding the error for FLOW_CLS_REPLACE operations where entry->in_use
is already true, causing tc_add_flow() to return 0 (success) for
unsupported replace requests.
Fixes: 425eabddaf ("net: stmmac: Implement L3/L4 Filters using TC Flower")
Signed-off-by: Rohan G Thomas <rohan.g.thomas@altera.com>
Signed-off-by: Nazim Amirul <muhammad.nazim.amirul.nazle.asmade@altera.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20260714023716.29865-4-muhammad.nazim.amirul.nazle.asmade@altera.com
Reviewed-by: Jakub Raczynski <j.raczynski@samsung.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The XGMAC_L4_ADDR register holds both source and destination port
match values. The current implementation overwrites the entire register
when configuring either port, so setting one silently erases the other.
Fix this by reading the register first, then masking and updating only
the relevant field before writing back.
Fixes: 425eabddaf ("net: stmmac: Implement L3/L4 Filters using TC Flower")
Signed-off-by: Rohan G Thomas <rohan.g.thomas@altera.com>
Signed-off-by: Nazim Amirul <muhammad.nazim.amirul.nazle.asmade@altera.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20260714023716.29865-3-muhammad.nazim.amirul.nazle.asmade@altera.com
Reviewed-by: Jakub Raczynski <j.raczynski@samsung.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
bpf_iter_tcp_batch() releases the current batch via
bpf_iter_tcp_put_batch(), which drops the socket refs and rewrites
each slot with the socket cookie, then grows the batch. cur_sk/end_sk
are kept for bpf_iter_tcp_resume(), but on realloc failure the function
returns ERR_PTR() before resume runs, leaving cur_sk < end_sk over
slots that now hold cookies rather than sock pointers.
bpf_iter_tcp_seq_stop() then calls bpf_iter_tcp_put_batch() again and
dereferences a cookie as a struct sock.
Empty the batch on the failure path so stop() does not release it
again. The sockets were already freed by the first
bpf_iter_tcp_put_batch(), so nothing leaks, and a later read() rescans
the bucket from the start instead of skipping it. The sibling
GFP_NOWAIT failure path still holds real socket references and is left
for stop() to release.
BUG: KASAN: null-ptr-deref in __sock_gen_cookie
Read of size 8 at addr 0000000000000059 by task exploit
...
__sock_gen_cookie (net/core/sock_diag.c:28)
bpf_iter_tcp_put_batch (net/ipv4/tcp_ipv4.c:2918)
bpf_iter_tcp_seq_stop (net/ipv4/tcp_ipv4.c:3270)
bpf_seq_read (kernel/bpf/bpf_iter.c:205)
vfs_read (fs/read_write.c:572)
ksys_read (fs/read_write.c:716)
do_syscall_64
entry_SYSCALL_64_after_hwframe
Kernel panic - not syncing: Fatal exception
Fixes: cdec67a489 ("bpf: tcp: Make sure iter->batch always contains a full bucket snapshot")
Reported-by: AutonomousCodeSecurity@microsoft.com
Signed-off-by: Xiang Mei (Microsoft) <xmei5@asu.edu>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Jordan Rife <jordan@jrife.io>
Link: https://patch.msgid.link/20260713233230.3553593-1-xmei5@asu.edu
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
x25_kill_by_neigh() walks the global X.25 socket list looking for sockets
attached to a terminating neighbour. x25_list_lock protects list membership
while the lookup is in progress, but it does not pin a socket's lifetime
after the lock is dropped.
The function currently drops x25_list_lock before calling lock_sock(s). A
concurrent close can run x25_release(), remove the same socket from
x25_list, and drop the last socket reference in that window. The neighbour
teardown path can then lock or inspect a freed struct sock/struct x25_sock.
Take sock_hold(s) while x25_list_lock still proves that the list entry is
live, then drop the temporary reference after the socket has been locked,
rechecked, and released. Recheck x25_sk(s)->neighbour after lock_sock(),
because another path may have disconnected the socket before this path
acquired the socket lock. Restart the list walk after each disconnect
because the list lock was dropped and the previous iterator state may no
longer be valid.
A QEMU/KASAN run against origin/master reproduced a slab-use-after-free in
x25_kill_by_neigh().
Fixes: 7781607938 ("net/x25: Fix null-ptr-deref caused by x25_disconnect")
Cc: stable@vger.kernel.org
Signed-off-by: David Lee <david.lee@trailofbits.com>
Assisted-by: Codex:gpt-5.5
Acked-by: Martin Schiller <ms@dev.tdt.de>
Link: https://patch.msgid.link/20260713104752.241175-1-david.lee@trailofbits.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
drm_gem_shmem_test_purge [1] and drm_gem_shmem_test_get_pages_sgt [2]
intermittently fail on ppc64le and s390x CI systems with a DMA address
overflow:
DMA addr 0x0000000100307000+4096 overflow (mask ffffffff, bus limit 0)
WARNING: kernel/dma/direct.h:114 dma_direct_map_sg+0x778/0x920
drm_gem_shmem_test_purge: ASSERTION FAILED at
drivers/gpu/drm/tests/drm_gem_shmem_test.c:330
Expected sgt is not error, but is: -5
The call chain leading to the failure is:
drm_gem_shmem_test_purge() / drm_gem_shmem_test_get_pages_sgt()
drm_gem_shmem_get_pages_sgt()
drm_gem_shmem_get_pages_sgt_locked() [drm_gem_shmem_helper.c]
dma_map_sgtable() [mapping.c]
__dma_map_sg_attrs()
dma_direct_map_sg() [direct.c]
dma_direct_map_phys() [kernel/dma/direct.h]
dma_capable() Checks addr against DMA mask
-> FAILS: addr > 0xFFFFFFFF
The root cause is that KUnit devices are initialized with a 32-bit DMA
mask (DMA_BIT_MASK(32)) in lib/kunit/device.c. On ppc64le and s390x
systems with physical memory above 4GB, page allocations can land at
addresses that exceed this mask. When drm_gem_shmem_get_pages_sgt()
attempts to DMA-map these pages via dma_map_sgtable(), the DMA layer
rejects the mapping because the physical address overflows the 32-bit
mask.
The failure is intermittent because pages may or may not be allocated
above 4GB on any given run depend on memory pressure.
Fix by setting a 64-bit DMA mask on the device before calling
drm_gem_shmem_get_pages_sgt() for all tests, following the same pattern
already used in drm_gem_shmem_test_obj_create_private().
[1] https://s3.amazonaws.com/arr-cki-prod-trusted-artifacts/trusted-artifacts/2643976103/test_s390x/15128551935/artifacts/jobwatch/logs/recipes/21561049/tasks/220716793/results/1014626315/logs/dmesg.log
[2] https://s3.amazonaws.com/arr-cki-prod-trusted-artifacts/trusted-artifacts/2643976103/test_ppc64le/15128551933/artifacts/jobwatch/logs/recipes/21561041/tasks/220716705/results/1014628163/logs/dmesg.log
Fixes: 93032ae634 ("drm/test: add a test suite for GEM objects backed by shmem")
Closes: https://datawarehouse.cki-project.org/issue/5345
Closes: https://datawarehouse.cki-project.org/issue/3184
Assisted-by: Claude:claude-4.6-opus
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: José Expósito <jose.exposito@redhat.com>
Link: https://patch.msgid.link/20260703150808.3832-1-jose.exposito89@gmail.com
Both TIPC_NL_MEDIA_SET and TIPC_NL_BEARER_SET accept user-supplied
MTU values but only enforce a minimum bound, not a maximum. When a user
sets the MTU to a value exceeding U16_MAX (65535), it passes validation
but is silently truncated when assigned to u16 fields l->mtu and
l->advertised_mtu in tipc_link_create(). Values like 65536 (0x10000)
truncate to 0, causing a division by zero in tipc_link_set_queue_limits()
which computes TIPC_MAX_PUBL / (l->mtu / ITEM_SIZE). Other overflowing
values (e.g. 65537-131071) produce small incorrect MTU values, resulting
in link malfunction behaviors.
Crash stack (triggered as unprivileged user via user namespace):
tipc_link_set_queue_limits net/tipc/link.c:2531
tipc_link_create net/tipc/link.c:520
tipc_node_check_dest net/tipc/node.c:1279
tipc_disc_rcv net/tipc/discover.c:252
tipc_rcv net/tipc/node.c:2129
tipc_udp_recv net/tipc/udp_media.c:392
Two independent paths lack the upper bound check:
1. tipc_udp_mtu_bad() -- called from __tipc_nl_media_set() (MEDIA_SET)
2. inline check in __tipc_nl_bearer_set() at bearer.c:1160 (BEARER_SET)
Fix both by rejecting MTU values above U16_MAX.
Fixes: 901271e040 ("tipc: implement configuration of UDP media MTU")
Reported-by: AutonomousCodeSecurity@microsoft.com
Closes: https://lore.kernel.org/all/CAB8m9WgETt0AjmFwE=F-CKjGXsK6_WDv0=kbYRcC8-noo+amnA@mail.gmail.com
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Signed-off-by: Cen Zhang (Microsoft) <blbllhy@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20260714041541.307702-1-blbllhy@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Commit 0baad6f9b9 ("fs/super: skip non-memcg-aware nr_cached_objects
in memcg slab shrink") added a check in fs/super.c that skipped every
->nr_cached_objects() hook whenever the shrinker was invoked for a
non-root memcg, on the assumption that none of them honour sc->memcg.
That assumption is wrong for XFS, whose inode-reclaim hook is
intentionally driven from per-memcg contexts to free memcg-charged
slab. Encoding a blanket "never memcg-aware" policy in fs/super.c
short-circuits that path.
Push the check down into the callbacks whose counters really are
irrelevant to per-memcg reclaim - btrfs_nr_cached_objects() and
shmem_unused_huge_count() - and drop the fs/super.c gate. Each
filesystem can now lift the restriction independently if its counter
later grows memcg awareness, without touching fs/super.c.
Introduce mem_cgroup_shrink_is_root() in <linux/memcontrol.h> so the
callbacks don't open-code "sc->memcg is NULL or root".
Fixes: 0baad6f9b9 ("fs/super: skip non-memcg-aware nr_cached_objects in memcg slab shrink")
Acked-by: Qi Zheng <qi.zheng@linux.dev>
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Shakeel Butt <shakeel.butt@linux.dev>
Signed-off-by: Usama Arif <usama.arif@linux.dev>
Link: https://patch.msgid.link/20260715103516.2410175-1-usama.arif@linux.dev
Acked-by: David Sterba <dsterba@suse.com>
Reviewed-by: Baolin Wang <baolin.wang@linux.alibaba.com>
Signed-off-by: Christian Brauner (Amutable) <brauner@kernel.org>
Different io_private values indicate distinct completion contexts that
must not be merged together, as this could leak or corrupt the private
data associated with each ioend.
Signed-off-by: Zhang Yi <yi.zhang@huawei.com>
Link: https://patch.msgid.link/20260713074206.1768006-1-yi.zhang@huaweicloud.com
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Ojaswin Mujoo <ojaswin@linux.ibm.com>
Signed-off-by: Christian Brauner (Amutable) <brauner@kernel.org>
Zhang Yi <yi.zhang@huaweicloud.com> says:
This patch series contains a few trivial iomap-related fixes in
preparation for converting ext4 buffered I/O to use iomap.
The first three patches are taken from my ext4 conversion series [1], as
suggested by Christoph. The fourth patch fixes a bug originally reported
by Sashiko during review of my series; although unrelated to the ext4
conversion, it is worth fixing on its own. Please see the following
patches for detail. The fifth patch add comments for
ifs_clear/set_range_dirty(), and the last patch avoids merging ioends
that have different private data.
[1] https://lore.kernel.org/linux-ext4/20260511072344.191271-1-yi.zhang@huaweicloud.com/
* patches from https://patch.msgid.link/20260714082325.325163-1-yi.zhang@huaweicloud.com:
iomap: add comments for ifs_clear/set_range_dirty()
iomap: fix out-of-bounds bitmap_set() with zero-length range
iomap: fix incorrect did_zero setting in iomap_zero_iter()
iomap: support invalidating partial folios
iomap: correct the range of a partial dirty clear
Link: https://patch.msgid.link/20260714082325.325163-1-yi.zhang@huaweicloud.com
Signed-off-by: Christian Brauner (Amutable) <brauner@kernel.org>
