commit bcb44433bb upstream.
Storage devices which report supporting discard commands like
WRITE_SAME_16 with unmap, but reject discard commands sent to the
storage device. This is a clear storage firmware bug but it doesn't
change the fact that should a program cause discards to be sent to a
multipath device layered on this buggy storage, all paths can end up
failed at the same time from the discards, causing possible I/O loss.
The first discard to a path will fail with Illegal Request, Invalid
field in cdb, e.g.:
kernel: sd 8:0:8:19: [sdfn] tag#0 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
kernel: sd 8:0:8:19: [sdfn] tag#0 Sense Key : Illegal Request [current]
kernel: sd 8:0:8:19: [sdfn] tag#0 Add. Sense: Invalid field in cdb
kernel: sd 8:0:8:19: [sdfn] tag#0 CDB: Write same(16) 93 08 00 00 00 00 00 a0 08 00 00 00 80 00 00 00
kernel: blk_update_request: critical target error, dev sdfn, sector 10487808
The SCSI layer converts this to the BLK_STS_TARGET error number, the sd
device disables its support for discard on this path, and because of the
BLK_STS_TARGET error multipath fails the discard without failing any
path or retrying down a different path. But subsequent discards can
cause path failures. Any discards sent to the path which already failed
a discard ends up failing with EIO from blk_cloned_rq_check_limits with
an "over max size limit" error since the discard limit was set to 0 by
the sd driver for the path. As the error is EIO, this now fails the
path and multipath tries to send the discard down the next path. This
cycle continues as discards are sent until all paths fail.
Fix this by training DM core to disable DISCARD if the underlying
storage already did so.
Also, fix branching in dm_done() and clone_endio() to reflect the
mutually exclussive nature of the IO operations in question.
Reported-by: David Jeffery <djeffery@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
[bwh: Backported to 3.16:
- Keep using op & flag to check operation type
- Keep using bdev_get_queue() to find queue in clone_endio()
- WRITE_ZEROES is not handled
- Use queue_flag_clear() instead of blk_queue_flag_clear()
- Adjust filenames, context
- Declare disable_discard() static as its only user is in the same
source file]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit ada770b1e7 upstream.
return_address returns the address that is one level higher in the call
stack than requested in its argument, because level 0 corresponds to its
caller's return address. Use requested level as the number of stack
frames to skip.
This fixes the address reported by might_sleep and friends.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit aa53e3bfac upstream.
Nikolay reported the following KASAN splat when running btrfs/048:
[ 1843.470920] ==================================================================
[ 1843.471971] BUG: KASAN: slab-out-of-bounds in strncmp+0x66/0xb0
[ 1843.472775] Read of size 1 at addr ffff888111e369e2 by task btrfs/3979
[ 1843.473904] CPU: 3 PID: 3979 Comm: btrfs Not tainted 5.2.0-rc3-default #536
[ 1843.475009] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1ubuntu1 04/01/2014
[ 1843.476322] Call Trace:
[ 1843.476674] dump_stack+0x7c/0xbb
[ 1843.477132] ? strncmp+0x66/0xb0
[ 1843.477587] print_address_description+0x114/0x320
[ 1843.478256] ? strncmp+0x66/0xb0
[ 1843.478740] ? strncmp+0x66/0xb0
[ 1843.479185] __kasan_report+0x14e/0x192
[ 1843.479759] ? strncmp+0x66/0xb0
[ 1843.480209] kasan_report+0xe/0x20
[ 1843.480679] strncmp+0x66/0xb0
[ 1843.481105] prop_compression_validate+0x24/0x70
[ 1843.481798] btrfs_xattr_handler_set_prop+0x65/0x160
[ 1843.482509] __vfs_setxattr+0x71/0x90
[ 1843.483012] __vfs_setxattr_noperm+0x84/0x130
[ 1843.483606] vfs_setxattr+0xac/0xb0
[ 1843.484085] setxattr+0x18c/0x230
[ 1843.484546] ? vfs_setxattr+0xb0/0xb0
[ 1843.485048] ? __mod_node_page_state+0x1f/0xa0
[ 1843.485672] ? _raw_spin_unlock+0x24/0x40
[ 1843.486233] ? __handle_mm_fault+0x988/0x1290
[ 1843.486823] ? lock_acquire+0xb4/0x1e0
[ 1843.487330] ? lock_acquire+0xb4/0x1e0
[ 1843.487842] ? mnt_want_write_file+0x3c/0x80
[ 1843.488442] ? debug_lockdep_rcu_enabled+0x22/0x40
[ 1843.489089] ? rcu_sync_lockdep_assert+0xe/0x70
[ 1843.489707] ? __sb_start_write+0x158/0x200
[ 1843.490278] ? mnt_want_write_file+0x3c/0x80
[ 1843.490855] ? __mnt_want_write+0x98/0xe0
[ 1843.491397] __x64_sys_fsetxattr+0xba/0xe0
[ 1843.492201] ? trace_hardirqs_off_thunk+0x1a/0x1c
[ 1843.493201] do_syscall_64+0x6c/0x230
[ 1843.493988] entry_SYSCALL_64_after_hwframe+0x49/0xbe
[ 1843.495041] RIP: 0033:0x7fa7a8a7707a
[ 1843.495819] Code: 48 8b 0d 21 de 2b 00 f7 d8 64 89 01 48 83 c8 ff c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 49 89 ca b8 be 00 00 00 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d ee dd 2b 00 f7 d8 64 89 01 48
[ 1843.499203] RSP: 002b:00007ffcb73bca38 EFLAGS: 00000202 ORIG_RAX: 00000000000000be
[ 1843.500210] RAX: ffffffffffffffda RBX: 00007ffcb73bda9d RCX: 00007fa7a8a7707a
[ 1843.501170] RDX: 00007ffcb73bda9d RSI: 00000000006dc050 RDI: 0000000000000003
[ 1843.502152] RBP: 00000000006dc050 R08: 0000000000000000 R09: 0000000000000000
[ 1843.503109] R10: 0000000000000002 R11: 0000000000000202 R12: 00007ffcb73bda91
[ 1843.504055] R13: 0000000000000003 R14: 00007ffcb73bda82 R15: ffffffffffffffff
[ 1843.505268] Allocated by task 3979:
[ 1843.505771] save_stack+0x19/0x80
[ 1843.506211] __kasan_kmalloc.constprop.5+0xa0/0xd0
[ 1843.506836] setxattr+0xeb/0x230
[ 1843.507264] __x64_sys_fsetxattr+0xba/0xe0
[ 1843.507886] do_syscall_64+0x6c/0x230
[ 1843.508429] entry_SYSCALL_64_after_hwframe+0x49/0xbe
[ 1843.509558] Freed by task 0:
[ 1843.510188] (stack is not available)
[ 1843.511309] The buggy address belongs to the object at ffff888111e369e0
which belongs to the cache kmalloc-8 of size 8
[ 1843.514095] The buggy address is located 2 bytes inside of
8-byte region [ffff888111e369e0, ffff888111e369e8)
[ 1843.516524] The buggy address belongs to the page:
[ 1843.517561] page:ffff88813f478d80 refcount:1 mapcount:0 mapping:ffff88811940c300 index:0xffff888111e373b8 compound_mapcount: 0
[ 1843.519993] flags: 0x4404000010200(slab|head)
[ 1843.520951] raw: 0004404000010200 ffff88813f48b008 ffff888119403d50 ffff88811940c300
[ 1843.522616] raw: ffff888111e373b8 000000000016000f 00000001ffffffff 0000000000000000
[ 1843.524281] page dumped because: kasan: bad access detected
[ 1843.525936] Memory state around the buggy address:
[ 1843.526975] ffff888111e36880: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 1843.528479] ffff888111e36900: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 1843.530138] >ffff888111e36980: fc fc fc fc fc fc fc fc fc fc fc fc 02 fc fc fc
[ 1843.531877] ^
[ 1843.533287] ffff888111e36a00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 1843.534874] ffff888111e36a80: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 1843.536468] ==================================================================
This is caused by supplying a too short compression value ('lz') in the
test-case and comparing it to 'lzo' with strncmp() and a length of 3.
strncmp() read past the 'lz' when looking for the 'o' and thus caused an
out-of-bounds read.
Introduce a new check 'btrfs_compress_is_valid_type()' which not only
checks the user-supplied value against known compression types, but also
employs checks for too short values.
Reported-by: Nikolay Borisov <nborisov@suse.com>
Fixes: 272e5326c7 ("btrfs: prop: fix vanished compression property after failed set")
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
[bwh: Backported to 3.16:
- "zstd" is not supported
- Add definition of btrfs_compression_types[]
- Include compression.h in props.c
- Adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 272e5326c7 upstream.
The compression property resets to NULL, instead of the old value if we
fail to set the new compression parameter.
$ btrfs prop get /btrfs compression
compression=lzo
$ btrfs prop set /btrfs compression zli
ERROR: failed to set compression for /btrfs: Invalid argument
$ btrfs prop get /btrfs compression
This is because the compression property ->validate() is successful for
'zli' as the strncmp() used the length passed from the userspace.
Fix it by using the expected string length in strncmp().
Fixes: 63541927c8 ("Btrfs: add support for inode properties")
Fixes: 5c1aab1dd5 ("btrfs: Add zstd support")
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
[bwh: Backported to 3.16: "zstd" is not supported]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 0e9f02450d upstream.
A NULL pointer dereference bug was reported on a distribution kernel but
the same issue should be present on mainline kernel. It occured on s390
but should not be arch-specific. A partial oops looks like:
Unable to handle kernel pointer dereference in virtual kernel address space
...
Call Trace:
...
try_to_wake_up+0xfc/0x450
vhost_poll_wakeup+0x3a/0x50 [vhost]
__wake_up_common+0xbc/0x178
__wake_up_common_lock+0x9e/0x160
__wake_up_sync_key+0x4e/0x60
sock_def_readable+0x5e/0x98
The bug hits any time between 1 hour to 3 days. The dereference occurs
in update_cfs_rq_h_load when accumulating h_load. The problem is that
cfq_rq->h_load_next is not protected by any locking and can be updated
by parallel calls to task_h_load. Depending on the compiler, code may be
generated that re-reads cfq_rq->h_load_next after the check for NULL and
then oops when reading se->avg.load_avg. The dissassembly showed that it
was possible to reread h_load_next after the check for NULL.
While this does not appear to be an issue for later compilers, it's still
an accident if the correct code is generated. Full locking in this path
would have high overhead so this patch uses READ_ONCE to read h_load_next
only once and check for NULL before dereferencing. It was confirmed that
there were no further oops after 10 days of testing.
As Peter pointed out, it is also necessary to use WRITE_ONCE() to avoid any
potential problems with store tearing.
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Valentin Schneider <valentin.schneider@arm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: 685207963b ("sched: Move h_load calculation to task_h_load()")
Link: https://lkml.kernel.org/r/20190319123610.nsivgf3mjbjjesxb@techsingularity.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
[bwh: Backported to 3.16: use ACCESS_ONCE()]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 8742dc86d0 upstream.
We currently don't reload pointers pointing into skb header
after doing pskb_may_pull() in _decode_session4(). So in case
pskb_may_pull() changed the pointers, we read from random
memory. Fix this by putting all the needed infos on the
stack, so that we don't need to access the header pointers
after doing pskb_may_pull().
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit ea673a4d3a upstream.
A call to pskb_may_pull may change the pointers into the packet,
so reload the pointers after the call.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 1a14f1e555 upstream.
We skip the header informations if the data pointer points
already behind the header in question for some protocols.
This is because we call pskb_may_pull with a negative value
converted to unsigened int from pskb_may_pull in this case.
Skipping the header informations can lead to incorrect policy
lookups, so fix it by a check of the data pointer position
before we call pskb_may_pull.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 1d3ff0950e upstream.
If dccp_feat_push_change fails, we forget free the mem
which is alloced by kmemdup in dccp_feat_clone_sp_val.
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: e8ef967a54 ("dccp: Registration routines for changing feature values")
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit eb40c0acdc upstream.
Some devices don't use blk_integrity but still want stable pages
because they do their own checksumming. Examples include rbd and iSCSI
when data digests are negotiated. Stacking DM (and thus LVM) on top of
these devices results in sporadic checksum errors.
Set BDI_CAP_STABLE_WRITES if any underlying device has it set.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
[bwh: Backported to 3.16: request_queue::backing_dev_info is a struct
not a pointer]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 7f75591fc5 upstream.
This fixes a possible circular locking dependency detected warning seen
with:
- CONFIG_PROVE_LOCKING=y
- consumer/provider IIO devices (ex: "voltage-divider" consumer of "adc")
When using the IIO consumer interface, e.g. iio_channel_get(), the consumer
device will likely call iio_read_channel_raw() or similar that rely on
'info_exist_lock' mutex.
typically:
...
mutex_lock(&chan->indio_dev->info_exist_lock);
if (chan->indio_dev->info == NULL) {
ret = -ENODEV;
goto err_unlock;
}
ret = do_some_ops()
err_unlock:
mutex_unlock(&chan->indio_dev->info_exist_lock);
return ret;
...
Same mutex is also hold in iio_device_unregister().
The following deadlock warning happens when:
- the consumer device has called an API like iio_read_channel_raw()
at least once.
- the consumer driver is unregistered, removed (unbind from sysfs)
======================================================
WARNING: possible circular locking dependency detected
4.19.24 #577 Not tainted
------------------------------------------------------
sh/372 is trying to acquire lock:
(kn->count#30){++++}, at: kernfs_remove_by_name_ns+0x3c/0x84
but task is already holding lock:
(&dev->info_exist_lock){+.+.}, at: iio_device_unregister+0x18/0x60
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (&dev->info_exist_lock){+.+.}:
__mutex_lock+0x70/0xa3c
mutex_lock_nested+0x1c/0x24
iio_read_channel_raw+0x1c/0x60
iio_read_channel_info+0xa8/0xb0
dev_attr_show+0x1c/0x48
sysfs_kf_seq_show+0x84/0xec
seq_read+0x154/0x528
__vfs_read+0x2c/0x15c
vfs_read+0x8c/0x110
ksys_read+0x4c/0xac
ret_fast_syscall+0x0/0x28
0xbedefb60
-> #0 (kn->count#30){++++}:
lock_acquire+0xd8/0x268
__kernfs_remove+0x288/0x374
kernfs_remove_by_name_ns+0x3c/0x84
remove_files+0x34/0x78
sysfs_remove_group+0x40/0x9c
sysfs_remove_groups+0x24/0x34
device_remove_attrs+0x38/0x64
device_del+0x11c/0x360
cdev_device_del+0x14/0x2c
iio_device_unregister+0x24/0x60
release_nodes+0x1bc/0x200
device_release_driver_internal+0x1a0/0x230
unbind_store+0x80/0x130
kernfs_fop_write+0x100/0x1e4
__vfs_write+0x2c/0x160
vfs_write+0xa4/0x17c
ksys_write+0x4c/0xac
ret_fast_syscall+0x0/0x28
0xbe906840
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&dev->info_exist_lock);
lock(kn->count#30);
lock(&dev->info_exist_lock);
lock(kn->count#30);
*** DEADLOCK ***
...
cdev_device_del() can be called without holding the lock. It should be safe
as info_exist_lock prevents kernelspace consumers to use the exported
routines during/after provider removal. cdev_device_del() is for userspace.
Help to reproduce:
See example: Documentation/devicetree/bindings/iio/afe/voltage-divider.txt
sysv {
compatible = "voltage-divider";
io-channels = <&adc 0>;
output-ohms = <22>;
full-ohms = <222>;
};
First, go to iio:deviceX for the "voltage-divider", do one read:
$ cd /sys/bus/iio/devices/iio:deviceX
$ cat in_voltage0_raw
Then, unbind the consumer driver. It triggers above deadlock warning.
$ cd /sys/bus/platform/drivers/iio-rescale/
$ echo sysv > unbind
Note I don't actually expect stable will pick this up all the
way back into IIO being in staging, but if's probably valid that
far back.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Fixes: ac917a8111 ("staging:iio:core set the iio_dev.info pointer to null on unregister")
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 0cf9135b77 upstream.
The CPUID flag ARCH_CAPABILITIES is unconditioinally exposed to host
userspace for all x86 hosts, i.e. KVM advertises ARCH_CAPABILITIES
regardless of hardware support under the pretense that KVM fully
emulates MSR_IA32_ARCH_CAPABILITIES. Unfortunately, only VMX hosts
handle accesses to MSR_IA32_ARCH_CAPABILITIES (despite KVM_GET_MSRS
also reporting MSR_IA32_ARCH_CAPABILITIES for all hosts).
Move the MSR_IA32_ARCH_CAPABILITIES handling to common x86 code so
that it's emulated on AMD hosts.
Fixes: 1eaafe91a0 ("kvm: x86: IA32_ARCH_CAPABILITIES is always supported")
Reported-by: Xiaoyao Li <xiaoyao.li@linux.intel.com>
Cc: Jim Mattson <jmattson@google.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
[bwh: Backported to 3.16:
- Keep using guest_cpuid_has_arch_capabilities() to check the CPUID
- Keep using rdmsrl() to get the initial value of IA32_ARCH_CAPABILITIES
- Adjust filenames, context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 1eaafe91a0 upstream.
If there is a possibility that a VM may migrate to a Skylake host,
then the hypervisor should report IA32_ARCH_CAPABILITIES.RSBA[bit 2]
as being set (future work, of course). This implies that
CPUID.(EAX=7,ECX=0):EDX.ARCH_CAPABILITIES[bit 29] should be
set. Therefore, kvm should report this CPUID bit as being supported
whether or not the host supports it. Userspace is still free to clear
the bit if it chooses.
For more information on RSBA, see Intel's white paper, "Retpoline: A
Branch Target Injection Mitigation" (Document Number 337131-001),
currently available at https://bugzilla.kernel.org/show_bug.cgi?id=199511.
Since the IA32_ARCH_CAPABILITIES MSR is emulated in kvm, there is no
dependency on hardware support for this feature.
Signed-off-by: Jim Mattson <jmattson@google.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Fixes: 28c1c9fabf ("KVM/VMX: Emulate MSR_IA32_ARCH_CAPABILITIES")
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit ddba91801a upstream.
KVM's API requires thats ioctls must be issued from the same process
that created the VM. In other words, userspace can play games with a
VM's file descriptors, e.g. fork(), SCM_RIGHTS, etc..., but only the
creator can do anything useful. Explicitly reject device ioctls that
are issued by a process other than the VM's creator, and update KVM's
API documentation to extend its requirements to device ioctls.
Fixes: 852b6d57dc ("kvm: add device control API")
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 8c7ae38d1c upstream.
The marshalling of AFS.StoreData, AFS.StoreData64 and YFS.StoreData64 calls
generated by ->setattr() ops for the purpose of expanding a file is
incorrect due to older documentation incorrectly describing the way the RPC
'FileLength' parameter is meant to work.
The older documentation says that this is the length the file is meant to
end up at the end of the operation; however, it was never implemented this
way in any of the servers, but rather the file is truncated down to this
before the write operation is effected, and never expanded to it (and,
indeed, it was renamed to 'TruncPos' in 2014).
Fix this by setting the position parameter to the new file length and doing
a zero-lengh write there.
The bug causes Xwayland to SIGBUS due to unexpected non-expansion of a file
it then mmaps. This can be tested by giving the following test program a
filename in an AFS directory:
#include <stdio.h>
#include <stdlib.h>
#include <unistd.h>
#include <fcntl.h>
#include <sys/mman.h>
int main(int argc, char *argv[])
{
char *p;
int fd;
if (argc != 2) {
fprintf(stderr,
"Format: test-trunc-mmap <file>\n");
exit(2);
}
fd = open(argv[1], O_RDWR | O_CREAT | O_TRUNC);
if (fd < 0) {
perror(argv[1]);
exit(1);
}
if (ftruncate(fd, 0x140008) == -1) {
perror("ftruncate");
exit(1);
}
p = mmap(NULL, 4096, PROT_READ | PROT_WRITE,
MAP_SHARED, fd, 0);
if (p == MAP_FAILED) {
perror("mmap");
exit(1);
}
p[0] = 'a';
if (munmap(p, 4096) < 0) {
perror("munmap");
exit(1);
}
if (close(fd) < 0) {
perror("close");
exit(1);
}
exit(0);
}
Fixes: 31143d5d51 ("AFS: implement basic file write support")
Reported-by: Jonathan Billings <jsbillin@umich.edu>
Tested-by: Jonathan Billings <jsbillin@umich.edu>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[bwh: Backported to 3.16: drop change in yfsclient.c]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit a595ecdd5f upstream.
Lorenz Messtechnik has a device that is controlled by the cp210x driver,
so add the device id to the driver. The device id was provided by
Silicon-Labs for the devices from this vendor.
Reported-by: Uli <t9cpu@web.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 242ec14551 upstream.
Suppose more than one non-NPIV FCP device is active on the same channel.
Send I/O to storage and have some of the pending I/O run into a SCSI
command timeout, e.g. due to bit errors on the fibre. Now the error
situation stops. However, we saw FCP requests continue to timeout in the
channel. The abort will be successful, but the subsequent TUR fails.
Scsi_eh starts. The LUN reset fails. The target reset fails. The host
reset only did an FCP device recovery. However, for non-NPIV FCP devices,
this does not close and reopen ports on the SAN-side if other non-NPIV FCP
device(s) share the same open ports.
In order to resolve the continuing FCP request timeouts, we need to
explicitly close and reopen ports on the SAN-side.
This was missing since the beginning of zfcp in v2.6.0 history commit
ea127f975424 ("[PATCH] s390 (7/7): zfcp host adapter.").
Note: The FSF requests for forced port reopen could run into FSF request
timeouts due to other reasons. This would trigger an internal FCP device
recovery. Pending forced port reopen recoveries would get dismissed. So
some ports might not get fully reopened during this host reset handler.
However, subsequent I/O would trigger the above described escalation and
eventually all ports would be forced reopen to resolve any continuing FCP
request timeouts due to earlier bit errors.
Signed-off-by: Steffen Maier <maier@linux.ibm.com>
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Reviewed-by: Jens Remus <jremus@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit fe67888fc0 upstream.
An already deleted SCSI device can exist on the Scsi_Host and remain there
because something still holds a reference. A new SCSI device with the same
H:C:T:L and FCP device, target port WWPN, and FCP LUN can be created. When
we try to unblock an rport, we still find the deleted SCSI device and
return early because the zfcp_scsi_dev of that SCSI device is not
ZFCP_STATUS_COMMON_UNBLOCKED. Hence we miss to unblock the rport, even if
the new proper SCSI device would be in good state.
Therefore, skip deleted SCSI devices when iterating the sdevs of the shost.
[cf. __scsi_device_lookup{_by_target}() or scsi_device_get()]
The following abbreviated trace sequence can indicate such problem:
Area : REC
Tag : ersfs_3
LUN : 0x4045400300000000
WWPN : 0x50050763031bd327
LUN status : 0x40000000 not ZFCP_STATUS_COMMON_UNBLOCKED
Ready count : n not incremented yet
Running count : 0x00000000
ERP want : 0x01
ERP need : 0xc1 ZFCP_ERP_ACTION_NONE
Area : REC
Tag : ersfs_3
LUN : 0x4045400300000000
WWPN : 0x50050763031bd327
LUN status : 0x41000000
Ready count : n+1
Running count : 0x00000000
ERP want : 0x01
ERP need : 0x01
...
Area : REC
Level : 4 only with increased trace level
Tag : ertru_l
LUN : 0x4045400300000000
WWPN : 0x50050763031bd327
LUN status : 0x40000000
Request ID : 0x0000000000000000
ERP status : 0x01800000
ERP step : 0x1000
ERP action : 0x01
ERP count : 0x00
NOT followed by a trace record with tag "scpaddy"
for WWPN 0x50050763031bd327.
Signed-off-by: Steffen Maier <maier@linux.ibm.com>
Fixes: 6f2ce1c6af ("scsi: zfcp: fix rport unblock race with LUN recovery")
Reviewed-by: Jens Remus <jremus@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit d29f5aa0bc upstream.
So far we effectively clear the BMCR register. Some PHY's can deal
with this (e.g. because they reset BMCR to a default as part of a
soft-reset) whilst on others this causes issues because e.g. the
autoneg bit is cleared. Marvell is an example, see also thread [0].
So let's be a little bit more gentle and leave all bits we're not
interested in as-is. This change is needed for PHY drivers to
properly deal with the original patch.
[0] https://marc.info/?t=155264050700001&r=1&w=2
Fixes: 6e2d85ec05 ("net: phy: Stop with excessive soft reset")
Tested-by: Phil Reid <preid@electromag.com.au>
Tested-by: liweihang <liweihang@hisilicon.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backported to 3.16: open-code phy_set_bits()]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 113ce08109 upstream.
Currently PCM core sets each opened stream forcibly to SUSPENDED state
via snd_pcm_suspend_all() call, and the user-space is responsible for
re-triggering the resume manually either via snd_pcm_resume() or
prepare call. The scheme works fine usually, but there are corner
cases where the stream can't be resumed by that call: the streams
still in OPEN state before finishing hw_params. When they are
suspended, user-space cannot perform resume or prepare because they
haven't been set up yet. The only possible recovery is to re-open the
device, which isn't nice at all. Similarly, when a stream is in
DISCONNECTED state, it makes no sense to change it to SUSPENDED
state. Ditto for in SETUP state; which you can re-prepare directly.
So, this patch addresses these issues by filtering the PCM streams to
be suspended by checking the PCM state. When a stream is in either
OPEN, SETUP or DISCONNECTED as well as already SUSPENDED, the suspend
action is skipped.
To be noted, this problem was originally reported for the PCM runtime
PM on HD-audio. And, the runtime PM problem itself was already
addressed (although not intended) by the code refactoring commits
3d21ef0b49 ("ALSA: pcm: Suspend streams globally via device type PM
ops") and 17bc4815de ("ALSA: pci: Remove superfluous
snd_pcm_suspend*() calls"). These commits eliminated the
snd_pcm_suspend*() calls from the runtime PM suspend callback code
path, hence the racy OPEN state won't appear while runtime PM.
(FWIW, the race window is between snd_pcm_open_substream() and the
first power up in azx_pcm_open().)
Although the runtime PM issue was already "fixed", the same problem is
still present for the system PM, hence this patch is still needed.
And for stable trees, this patch alone should suffice for fixing the
runtime PM problem, too.
Reported-and-tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit f131a56880 upstream.
The batadv_hash_remove is a function which searches the hashtable for an
entry using a needle, a hashtable bucket selection function and a compare
function. It will lock the bucket list and delete an entry when the compare
function matches it with the needle. It returns the pointer to the
hlist_node which matches or NULL when no entry matches the needle.
The batadv_tt_global_free is not itself protected in anyway to avoid that
any other function is modifying the hashtable between the search for the
entry and the call to batadv_hash_remove. It can therefore happen that the
entry either doesn't exist anymore or an entry was deleted which is not the
same object as the needle. In such an situation, the reference counter (for
the reference stored in the hashtable) must not be reduced for the needle.
Instead the reference counter of the actually removed entry has to be
reduced.
Otherwise the reference counter will underflow and the object might be
freed before all its references were dropped. The kref helpers reported
this problem as:
refcount_t: underflow; use-after-free.
Fixes: 7683fdc1e8 ("batman-adv: protect the local and the global trans-tables with rcu")
Reported-by: Martin Weinelt <martin@linuxlounge.net>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Acked-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 3d65b9acca upstream.
The batadv_hash_remove is a function which searches the hashtable for an
entry using a needle, a hashtable bucket selection function and a compare
function. It will lock the bucket list and delete an entry when the compare
function matches it with the needle. It returns the pointer to the
hlist_node which matches or NULL when no entry matches the needle.
The batadv_tt_local_remove is not itself protected in anyway to avoid that
any other function is modifying the hashtable between the search for the
entry and the call to batadv_hash_remove. It can therefore happen that the
entry either doesn't exist anymore or an entry was deleted which is not the
same object as the needle. In such an situation, the reference counter (for
the reference stored in the hashtable) must not be reduced for the needle.
Instead the reference counter of the actually removed entry has to be
reduced.
Otherwise the reference counter will underflow and the object might be
freed before all its references were dropped. The kref helpers reported
this problem as:
refcount_t: underflow; use-after-free.
Fixes: ef72706a05 ("batman-adv: protect tt_local_entry from concurrent delete events")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 4ba104f468 upstream.
The batadv_hash_remove is a function which searches the hashtable for an
entry using a needle, a hashtable bucket selection function and a compare
function. It will lock the bucket list and delete an entry when the compare
function matches it with the needle. It returns the pointer to the
hlist_node which matches or NULL when no entry matches the needle.
The batadv_bla_del_claim is not itself protected in anyway to avoid that
any other function is modifying the hashtable between the search for the
entry and the call to batadv_hash_remove. It can therefore happen that the
entry either doesn't exist anymore or an entry was deleted which is not the
same object as the needle. In such an situation, the reference counter (for
the reference stored in the hashtable) must not be reduced for the needle.
Instead the reference counter of the actually removed entry has to be
reduced.
Otherwise the reference counter will underflow and the object might be
freed before all its references were dropped. The kref helpers reported
this problem as:
refcount_t: underflow; use-after-free.
Fixes: 23721387c4 ("batman-adv: add basic bridge loop avoidance code")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
[bwh: Backported to 3.16: keep using batadv_claim_free_ref()]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit fccfb9ce70 upstream.
The desired channel has to be selected in order to correctly fill the
buffer with the corresponding data.
The `ad_sd_write_reg()` already does this, but for the
`ad_sd_read_reg_raw()` this was omitted.
Fixes: af3008485e ("iio:adc: Add common code for ADI Sigma Delta devices")
Signed-off-by: Dragos Bogdan <dragos.bogdan@analog.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit d92f2c59cc upstream.
Commit 2f31a67f01 ("usb: xhci: Prevent bus suspend if a port connect
change or polling state is detected") was intended to prevent ports that
were still link training from being forced to U3 suspend state mid
enumeration.
This solved enumeration issues for devices with slow link training.
Turns out some devices are stuck in the link training/polling state,
and thus that patch will prevent suspend completely for these devices.
This is seen with USB3 card readers in some MacBooks.
Instead of preventing suspend, give some time to complete the link
training. On successful training the port will end up as connected
and enabled.
If port instead is stuck in link training the bus suspend will continue
suspending after 360ms (10 * 36ms) timeout (tPollingLFPSTimeout).
Original patch was sent to stable, this one should go there as well
Fixes: 2f31a67f01 ("usb: xhci: Prevent bus suspend if a port connect change or polling state is detected")
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit c5bc6e526d upstream.
Current code test wrong value so it does not verify if the written
data is correctly read back. Fix it.
Also make it return -EPERM if read value does not match written bit,
just like it done for adnp_gpio_direction_output().
Fixes: 5e969a401a ("gpio: Add Avionic Design N-bit GPIO expander support")
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit ca0214ee28 upstream.
The PCM OSS emulation converts and transfers the data on the fly via
"plugins". The data is converted over the dynamically allocated
buffer for each plugin, and recently syzkaller caught OOB in this
flow.
Although the bisection by syzbot pointed out to the commit
65766ee0bf ("ALSA: oss: Use kvzalloc() for local buffer
allocations"), this is merely a commit to replace vmalloc() with
kvmalloc(), hence it can't be the cause. The further debug action
revealed that this happens in the case where a slave PCM doesn't
support only the stereo channels while the OSS stream is set up for a
mono channel. Below is a brief explanation:
At each OSS parameter change, the driver sets up the PCM hw_params
again in snd_pcm_oss_change_params_lock(). This is also the place
where plugins are created and local buffers are allocated. The
problem is that the plugins are created before the final hw_params is
determined. Namely, two snd_pcm_hw_param_near() calls for setting the
period size and periods may influence on the final result of channels,
rates, etc, too, while the current code has already created plugins
beforehand with the premature values. So, the plugin believes that
channels=1, while the actual I/O is with channels=2, which makes the
driver reading/writing over the allocated buffer size.
The fix is simply to move the plugin allocation code after the final
hw_params call.
Reported-by: syzbot+d4503ae45b65c5bc1194@syzkaller.appspotmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 5a07168d8d upstream.
The futex code requires that the user space addresses of futexes are 32bit
aligned. sys_futex() checks this in futex_get_keys() but the robust list
code has no alignment check in place.
As a consequence the kernel crashes on architectures with strict alignment
requirements in handle_futex_death() when trying to cmpxchg() on an
unaligned futex address which was retrieved from the robust list.
[ tglx: Rewrote changelog, proper sizeof() based alignement check and add
comment ]
Fixes: 0771dfefc9 ("[PATCH] lightweight robust futexes: core")
Signed-off-by: Chen Jie <chenjie6@huawei.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: <dvhart@infradead.org>
Cc: <peterz@infradead.org>
Cc: <zengweilin@huawei.com>
Link: https://lkml.kernel.org/r/1552621478-119787-1-git-send-email-chenjie6@huawei.com
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 5bb71fc790 upstream.
The spec states in 10.4.16 that the Protected Memory Enable
Register should be treated as read-only for implementations
not supporting protected memory regions (PLMR and PHMR fields
reported as Clear in the Capability register).
Cc: Jacob Pan <jacob.jun.pan@linux.intel.com>
Cc: mark gross <mgross@intel.com>
Suggested-by: Ashok Raj <ashok.raj@intel.com>
Fixes: f8bab73515 ("intel-iommu: PMEN support")
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit c709f14f06 upstream.
dev is indirectly controlled by user-space, hence leading to
a potential exploitation of the Spectre variant 1 vulnerability.
This issue was detected with the help of Smatch:
sound/core/seq/oss/seq_oss_synth.c:626 snd_seq_oss_synth_make_info() warn: potential spectre issue 'dp->synths' [w] (local cap)
Fix this by sanitizing dev before using it to index dp->synths.
Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].
[1] https://lore.kernel.org/lkml/20180423164740.GY17484@dhcp22.suse.cz/
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 2b1d9c8f87 upstream.
info->stream is indirectly controlled by user-space, hence leading to
a potential exploitation of the Spectre variant 1 vulnerability.
This issue was detected with the help of Smatch:
sound/core/rawmidi.c:604 __snd_rawmidi_info_select() warn: potential spectre issue 'rmidi->streams' [r] (local cap)
Fix this by sanitizing info->stream before using it to index
rmidi->streams.
Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].
[1] https://lore.kernel.org/lkml/20180423164740.GY17484@dhcp22.suse.cz/
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 22c971db7d upstream.
Colin King reported a bug in read_bbreg_hdl():
memcpy(pcmd->rsp, (u8 *)&val, pcmd->rspsz);
The problem is that "val" is uninitialized.
This code is obviously not useful, but so far as I can tell
"pcmd->cmdcode" is never GEN_CMD_CODE(_Read_BBREG) so it's not harmful
either. For now the easiest fix is to just call r8712_free_cmd_obj()
and return.
Fixes: 2865d42c78 ("staging: r8712u: Add the new driver to the mainline kernel")
Reported-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 2908b076f5 upstream.
The write_parport_reg_nonblock() helper takes a reference to the struct
mos_parport, but failed to release it in a couple of error paths after
allocation failures, leading to a memory leak.
Johan said that move the kref_get() and mos_parport assignment to the
end of urbtrack initialisation is a better way, so move it. and
mos_parport do not used until urbtrack initialisation.
Signed-off-by: Lin Yi <teroincn@163.com>
Fixes: b69578df7e ("USB: usbserial: mos7720: add support for parallel port on moschip 7715")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 032f85c936 upstream.
Increase the reset duration to ensure correct phy functionality. The
reset duration is taken from barebox commit 52fdd510de ("ARM: dts:
pfla02: use long enough reset for ethernet phy"):
Use a longer reset time for ethernet phy Micrel KSZ9031RNX. Otherwise a
small percentage of modules have 'transmission timeouts' errors like
barebox@Phytec phyFLEX-i.MX6 Quad Carrier-Board:/ ifup eth0
warning: No MAC address set. Using random address 7e:94:4d:02:f8:f3
eth0: 1000Mbps full duplex link detected
eth0: transmission timeout
T eth0: transmission timeout
T eth0: transmission timeout
T eth0: transmission timeout
T eth0: transmission timeout
Cc: Stefan Christ <s.christ@phytec.de>
Cc: Christian Hemp <c.hemp@phytec.de>
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Fixes: 3180f95666 ("ARM: dts: Phytec imx6q pfla02 and pbab01 support")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit fb6fafbc7d upstream.
clang points out a harmless signed integer overflow:
drivers/net/ethernet/3com/3c515.c:1530:66: error: implicit conversion from 'int' to 'short' changes value from 32783 to -32753 [-Werror,-Wconstant-conversion]
new_mode = SetRxFilter | RxStation | RxMulticast | RxBroadcast | RxProm;
~ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~
drivers/net/ethernet/3com/3c515.c:1532:52: error: implicit conversion from 'int' to 'short' changes value from 32775 to -32761 [-Werror,-Wconstant-conversion]
new_mode = SetRxFilter | RxStation | RxMulticast | RxBroadcast;
~ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~
drivers/net/ethernet/3com/3c515.c:1534:38: error: implicit conversion from 'int' to 'short' changes value from 32773 to -32763 [-Werror,-Wconstant-conversion]
new_mode = SetRxFilter | RxStation | RxBroadcast;
~ ~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~
Make the variable unsigned to avoid the overflow.
Fixes: Linux-2.1.128pre1
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit e0aa67709f upstream.
When a dual stack dccp listener accepts an ipv4 flow,
it should not attempt to use an ipv6 header or
inet6_iif() helper.
Fixes: 3df80d9320 ("[DCCP]: Introduce DCCPv6")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 89e4130939 upstream.
When a dual stack tcp listener accepts an ipv4 flow,
it should not attempt to use an ipv6 header or tcp_v6_iif() helper.
Fixes: 1397ed35f2 ("ipv6: add flowinfo for tcp6 pkt_options for all cases")
Fixes: df3687ffc6 ("ipv6: add the IPV6_FL_F_REFLECT flag to IPV6_FL_A_GET")
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit a3e23f719f upstream.
In netdev_queue_add_kobject and rx_queue_add_kobject,
if sysfs_create_group failed, kobject_put will call
netdev_queue_release to decrease dev refcont, however
dev_hold has not be called. So we will see this while
unregistering dev:
unregister_netdevice: waiting for bcsh0 to become free. Usage count = -1
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: d0d6683716 ("net: don't decrement kobj reference count on init failure")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit d982b33133 upstream.
=================================================================
==20875==ERROR: LeakSanitizer: detected memory leaks
Direct leak of 1160 byte(s) in 1 object(s) allocated from:
#0 0x7f1b6fc84138 in calloc (/usr/lib/x86_64-linux-gnu/libasan.so.5+0xee138)
#1 0x55bd50005599 in zalloc util/util.h:23
#2 0x55bd500068f5 in perf_evsel__newtp_idx util/evsel.c:327
#3 0x55bd4ff810fc in perf_evsel__newtp /home/work/linux/tools/perf/util/evsel.h:216
#4 0x55bd4ff81608 in test__perf_evsel__tp_sched_test tests/evsel-tp-sched.c:69
#5 0x55bd4ff528e6 in run_test tests/builtin-test.c:358
#6 0x55bd4ff52baf in test_and_print tests/builtin-test.c:388
#7 0x55bd4ff543fe in __cmd_test tests/builtin-test.c:583
#8 0x55bd4ff5572f in cmd_test tests/builtin-test.c:722
#9 0x55bd4ffc4087 in run_builtin /home/changbin/work/linux/tools/perf/perf.c:302
#10 0x55bd4ffc45c6 in handle_internal_command /home/changbin/work/linux/tools/perf/perf.c:354
#11 0x55bd4ffc49ca in run_argv /home/changbin/work/linux/tools/perf/perf.c:398
#12 0x55bd4ffc5138 in main /home/changbin/work/linux/tools/perf/perf.c:520
#13 0x7f1b6e34809a in __libc_start_main (/lib/x86_64-linux-gnu/libc.so.6+0x2409a)
Indirect leak of 19 byte(s) in 1 object(s) allocated from:
#0 0x7f1b6fc83f30 in __interceptor_malloc (/usr/lib/x86_64-linux-gnu/libasan.so.5+0xedf30)
#1 0x7f1b6e3ac30f in vasprintf (/lib/x86_64-linux-gnu/libc.so.6+0x8830f)
Signed-off-by: Changbin Du <changbin.du@gmail.com>
Reviewed-by: Jiri Olsa <jolsa@kernel.org>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt (VMware) <rostedt@goodmis.org>
Fixes: 6a6cd11d4e ("perf test: Add test for the sched tracepoint format fields")
Link: http://lkml.kernel.org/r/20190316080556.3075-17-changbin.du@gmail.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 0fcc4c8c04 upstream.
When dev_exception_add() returns an error (due to a failed memory
allocation), make sure that we move the RCU preemption count back to where
it was before we were called. We dropped the RCU read lock inside the loop
body, so we can't just "break".
sparse complains about this, too:
$ make -s C=2 security/device_cgroup.o
./include/linux/rcupdate.h:647:9: warning: context imbalance in
'propagate_exception' - unexpected unlock
Fixes: d591fb5661 ("device_cgroup: simplify cgroup tree walk in propagate_exception()")
Signed-off-by: Jann Horn <jannh@google.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 93bcefd4c6 upstream.
We disable transmission interrupt (clear SCSCR_TIE) after all data has been transmitted
(if uart_circ_empty(xmit)). While transmitting, if the data is still in the tty buffer,
re-enable the SCSCR_TIE bit, which was done at sci_start_tx().
This is unnecessary processing, wasting CPU operation if the data transmission length is large.
And further, transmit end, FIFO empty bits disabling have also been performed in the step above.
Signed-off-by: Hoan Nguyen An <na-hoan@jinso.co.jp>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 6734330654 upstream.
In case ioremap fails, the fix returns -ENOMEM to avoid NULL
pointer dereferences.
Multiple places use port.membase.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[bwh: Backported to 3.16: There is no out_disable_clks label, so goto
out_free_clk on error]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 3a10e3dd52 upstream.
of_match_device can return a NULL pointer when matching device is not
found. This patch avoids a scenario causing NULL pointer derefernce.
Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 422c2537ba upstream.
Add PIDs for the NovaTech OrionLX+ and Orion I/O so they can be
automatically detected.
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 91740fc824 upstream.
In the current cpuidle implementation for i.MX6q, the CPU that sets
'WAIT_UNCLOCKED' and the CPU that returns to 'WAIT_CLOCKED' are always
the same. While the CPU that sets 'WAIT_UNCLOCKED' is in IDLE state of
"WAIT", if the other CPU wakes up and enters IDLE state of "WFI"
istead of "WAIT", this CPU can not wake up at expired time.
Because, in the case of "WFI", the CPU must be waked up by the local
timer interrupt. But, while 'WAIT_UNCLOCKED' is set, the local timer
is stopped, when all CPUs execute "wfi" instruction. As a result, the
local timer interrupt is not fired.
In this situation, this CPU will wake up by IRQ different from local
timer. (e.g. broacast timer)
So, this fix changes CPU to return to 'WAIT_CLOCKED'.
Signed-off-by: Kohji Okuno <okuno.kohji@jp.panasonic.com>
Fixes: e5f9dec8ff ("ARM: imx6q: support WAIT mode using cpuidle")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
[bwh: Backported to 3.16: use imx6q_set_lpm() instead of imx6_set_lpm()]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 4a9be28c45 upstream.
If the last NFSv3 unmount from a given host races with a mount from the
same host, we can destroy an nlm_host that is still in use.
Specifically nlmclnt_lookup_host() can increment h_count on
an nlm_host that nlmclnt_release_host() has just successfully called
refcount_dec_and_test() on.
Once nlmclnt_lookup_host() drops the mutex, nlm_destroy_host_lock()
will be called to destroy the nlmclnt which is now in use again.
The cause of the problem is that the dec_and_test happens outside the
locked region. This is easily fixed by using
refcount_dec_and_mutex_lock().
Fixes: 8ea6ecc8b0 ("lockd: Create client-side nlm_host cache")
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
[bwh: Backported to 3.16: use atomic instead of refcount API]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 273160ffc6 upstream.
sctp_hdr(skb) only works when skb->transport_header is set properly.
But in Netfilter, skb->transport_header for ipv6 is not guaranteed
to be right value for sctphdr. It would cause to fail to check the
checksum for sctp packets.
So fix it by using offset, which is always right in all places.
v1->v2:
- Fix the changelog.
Fixes: e6d8b64b34 ("net: sctp: fix and consolidate SCTP checksumming code")
Reported-by: Li Shuang <shuali@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit bb9e5c5bcd upstream.
The bug that Stan reported is as follows. After a restart, a 16-bit NIC
may be incorrectly identified as a 32-bit NIC and stop working.
mac8390 slot.E: Memory length resource not found, probing
mac8390 slot.E: Farallon EtherMac II-C (type farallon)
mac8390 slot.E: MAC 00:00:c5:30:c2:99, IRQ 61, 32 KB shared memory at 0xfeed0000, 32-bit access.
The bug never arises after a cold start and only intermittently after a
warm start. (I didn't investigate why the bug is intermittent.)
It turns out that memcpy_toio() is deprecated and memcmp_withio() also
has issues. Replacing these calls with mmio accessors fixes the problem.
Reported-and-tested-by: Stan Johnson <userm57@yahoo.com>
Fixes: 2964db0f59 ("m68k: Mac DP8390 update")
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
