commit 57c10915f2 upstream.
rmi_f3a_initialize() takes the GPIO count from the device query register
(f3a->gpio_count = buf & RMI_F3A_GPIO_COUNT, range 0..127).
rmi_f3a_map_gpios() then allocates gpio_key_map with
min(gpio_count, TRACKSTICK_RANGE_END) == at most 6 entries, but
rmi_f3a_attention() iterates the full gpio_count and dereferences
gpio_key_map[i], and input->keycodemax is set to the full gpio_count
while input->keycode points at the 6-entry allocation.
A device that reports gpio_count > 6 therefore causes an out-of-bounds
read of gpio_key_map[] on every attention interrupt, and out-of-bounds
accesses through the input core's default keymap ioctls: EVIOCGKEYCODE
reads past the buffer (leaking adjacent slab memory to user space) and
EVIOCSKEYCODE writes a caller-controlled value past it, for any process
able to open the evdev node, since input_default_getkeycode() and
input_default_setkeycode() only bound the index against keycodemax.
Size the keymap for the full gpio_count. The mapping loop is unchanged:
it still assigns only the first min(gpio_count, TRACKSTICK_RANGE_END)
entries; the remaining slots stay KEY_RESERVED (devm_kcalloc zero-fills)
and are skipped when reporting.
Fixes: 9e4c596bfd ("Input: synaptics-rmi4 - add support for F3A")
Cc: stable@vger.kernel.org
Signed-off-by: Bryam Vargas <hexlabsecurity@proton.me>
Link: https://patch.msgid.link/20260614-b4-disp-818d6bda-v1-1-cf39a3615085@proton.me
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6251f7d347 upstream.
If rmi_register_physical_driver() fails, the current error path
unregisters only the RMI bus. The function handlers registered
earlier remain registered with the driver core.
Add a separate error path to unregister the function handlers
before unregistering the bus in this failure case.
Fixes: 2b6a321da9 ("Input: synaptics-rmi4 - add support for Synaptics RMI4 devices")
Signed-off-by: Haoxiang Li <haoxiang_li2024@163.com>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20260610064633.2837084-1-haoxiang_li2024@163.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 111bb7f9f4 upstream.
stm32f7_i2c_compute_timing() derives the I2C clock source period
(i2cclk) with DIV_ROUND_CLOSEST, which may round it up. When the
period is overestimated, all timings computed from it (SCLDEL,
SDADEL, SCLL, SCLH) come out shorter on the wire than calculated,
and the resulting bus rate can exceed the requested speed, violating
the I2C specification minimums for tLOW and tHIGH.
For example, with a 104.45 MHz clock source (e.g. PCLK1, the
reset-default I2C clock source on STM32MP1), i2cclk is rounded from
9.574 ns up to 10 ns. Requesting a 400 kHz fast mode bus with
72/27 ns rise/fall times and no analog/digital filters then produces
an actual bus rate of 415.6 kHz with tLOW = 1254 ns, violating both
the 400 kHz maximum rate and the 1300 ns tLOW minimum of the
specification.
Truncate the period instead, so that it can only be underestimated.
The error then falls on the safe side: the programmed timings come
out slightly longer than computed and the bus runs marginally below
the target rate (375.3 kHz in the example above) while meeting the
specification.
i2cbus is left rounded-to-closest: it is only used as the target of
the clk_error comparison and is never multiplied into the programmed
timings, so nearest rounding remains accurate there.
Fixes: aeb068c572 ("i2c: i2c-stm32f7: add driver")
Signed-off-by: Guillermo Rodríguez <guille.rodriguez@gmail.com>
Cc: <stable@vger.kernel.org> # v4.14+
Acked-by: Alain Volmat <alain.volmat@foss.st.com>
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@foss.st.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20260611104857.242153-1-guille.rodriguez@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b1a58ed9ea upstream.
Adapters can be looked up by their id using i2c_get_adapter() which
takes a reference to the embedded struct device.
Remove the adapter from the IDR before tearing it down during
deregistration (and on registration failure) to make sure its resources
are not accessed after having been freed (e.g. the device name).
Fixes: 35fc37f818 ("i2c: Limit core locking to the necessary sections")
Cc: stable@vger.kernel.org # 2.6.31
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fb7b1a0ab2 upstream.
begin_cpu_udmabuf() maps the sg_table with the caller-provided direction
(e.g., DMA_TO_DEVICE for a write-only sync), and caches it in ubuf->sg
for reuse. However, release_udmabuf() always unmaps this sg_table with
a hardcoded DMA_BIDIRECTIONAL, regardless of the direction that was
originally used for the mapping.
With CONFIG_DMA_API_DEBUG=y this produces:
DMA-API: misc udmabuf: device driver frees DMA memory with different
direction [device address=0x000000044a123000] [size=4096 bytes]
[mapped with DMA_TO_DEVICE] [unmapped with DMA_BIDIRECTIONAL]
The issue was found during video playback when GStreamer performed a
write-only DMA_BUF_IOCTL_SYNC on a udmabuf. It can be reproduced
with CONFIG_DMA_API_DEBUG=y by creating a udmabuf from a memfd,
performing a write-only sync (DMA_BUF_SYNC_WRITE without
DMA_BUF_SYNC_READ), and closing the file descriptor.
Fix this by storing the DMA direction used when the sg_table is first
created in begin_cpu_udmabuf(), and passing that same direction to
put_sg_table() in release_udmabuf().
Fixes: 284562e1f3 ("udmabuf: implement begin_cpu_access/end_cpu_access hooks")
Cc: stable@vger.kernel.org
Signed-off-by: Mikhail Gavrilov <mikhail.v.gavrilov@gmail.com>
Reviewed-by: Vivek Kasireddy <vivek.kasireddy@intel.com>
Signed-off-by: Vivek Kasireddy <vivek.kasireddy@intel.com>
Link: https://patch.msgid.link/20260314232722.15555-1-mikhail.v.gavrilov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3a1230e7b0 upstream.
In exfat_find_dir_entry(), each TYPE_EXTEND (file name) entry advances the
output pointer by a fixed amount while the loop guard only tracks the
accumulated name length:
if (++order == 2)
uniname = p_uniname->name;
else
uniname += EXFAT_FILE_NAME_LEN;
len = exfat_extract_uni_name(ep, entry_uniname);
name_len += len;
unichar = *(uniname+len);
*(uniname+len) = 0x0;
uniname grows by EXFAT_FILE_NAME_LEN (15) per name entry, but name_len
grows only by the actual extracted length, which is shorter when a name
fragment contains an early NUL. The only guard is
`name_len >= MAX_NAME_LENGTH`, so a crafted directory with many short
name fragments lets uniname run far past the
p_uniname->name[MAX_NAME_LENGTH + 3] buffer while name_len stays small,
causing an out-of-bounds read and write at *(uniname+len).
The sibling extractor exfat_get_uniname_from_ext_entry() already stops
on a short fragment (the lockstep `len != EXFAT_FILE_NAME_LEN` guard
added in commit d42334578e ("exfat: check if filename entries exceeds
max filename length")); exfat_find_dir_entry() never got the
equivalent. Track the per-entry write offset as a count and reject a
fragment once the offset, or the offset plus the extracted length, would
exceed MAX_NAME_LENGTH, before forming the output pointer.
Fixes: ca06197382 ("exfat: add directory operations")
Cc: stable@vger.kernel.org
Suggested-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Bryam Vargas <hexlabsecurity@proton.me>
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5140f099ec upstream.
POSIX requires write permission to truncate a file, so an open() that
specifies O_TRUNC must be authorized for write access regardless of the
O_ACCMODE access mode.
nfs_open_permission_mask() builds the access mask passed to
nfs_may_open(), which is the local authorization gate for OPENs the
client serves itself from a cached write delegation via the
can_open_delegated() path in nfs4_try_open_cached(). The mask is
derived from O_ACCMODE alone, so an open(O_RDONLY | O_TRUNC) against a
file the caller cannot write requests only MAY_READ and passes the
local check. The OPEN is then satisfied locally and the truncation is
issued to the server as a SETATTR(size=0) over the delegation stateid,
which the server accepts under standard write-delegation semantics.
POSIX requires that this open fail with EACCES.
Include MAY_WRITE in the mask whenever O_TRUNC is set so the local
check matches the access the server would have enforced.
Suggested-by: Trond Myklebust <trondmy@kernel.org>
Fixes: af22f94ae0 ("NFSv4: Simplify _nfs4_do_access()")
Cc: stable@vger.kernel.org
Signed-off-by: Benjamin Coddington <bcodding@hammerspace.com>
Signed-off-by: Anna Schumaker <anna.schumaker@hammerspace.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0a6070839b upstream.
String event fields are not necessarily NUL-terminated, so the filter
predicate functions (filter_pred_string(), filter_pred_strloc() and
filter_pred_strrelloc()) pass the field length to the regex match
callbacks, and the length-aware matchers honour it.
regex_match_glob() was the exception: it ignored the length and called
glob_match(), which scans the string until it hits a NUL byte. Some
string fields are not NUL-terminated. One example is the dynamic char
array of the xfs_* namespace tracepoints, which is copied without a
trailing NUL. For such a field, glob matching reads past the end of
the event field, causing a KASAN slab-out-of-bounds read in
glob_match(), reached via regex_match_glob() and filter_match_preds()
from the xfs_lookup tracepoint.
Add a length-bounded glob_match_len() and use it from regex_match_glob()
so glob matching always stops at the field boundary. The matching loop
is factored into a shared helper so glob_match() keeps its behaviour.
Fixes: 60f1d5e3ba ("ftrace: Support full glob matching")
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/da1aaf125fc3b63320b0c540fd6afa7c3d5b4f1a.1782836943.git.hhhuang@smu.edu.sg
Reported-by: Yuan Tan <yuantan098@gmail.com>
Reported-by: Yifan Wu <yifanwucs@gmail.com>
Reported-by: Juefei Pu <tomapufckgml@gmail.com>
Reported-by: Zhengchuan Liang <zcliangcn@gmail.com>
Reported-by: Xin Liu <bird@lzu.edu.cn>
Assisted-by: Codex:GPT-5.4
Signed-off-by: Huihui Huang <hhhuang@smu.edu.sg>
Signed-off-by: Ren Wei <n05ec@lzu.edu.cn>
Acked-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 01980b5da5 upstream.
When dmaengine_prep_slave_sg() fails for the TX channel, the error path
terminates the TX DMA channel but leaves the RX channel running. Since
the RX channel was already submitted and issued prior to preparing
the TX descriptor, returning -EINVAL causes the SPI core to unmap the
DMA buffers while the RX DMA engine continues writing to them, leading
to potential memory corruption or use-after-free.
Terminate the RX channel before returning on the TX prepare failure path.
Fixes: 09c04466ce ("spi: lpspi: add dma mode support")
Cc: stable@vger.kernel.org
Signed-off-by: Carlos Song <carlos.song@nxp.com>
Link: https://patch.msgid.link/20260525062357.3191349-3-carlos.song@oss.nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e17ff3d6ff upstream.
In order to know if a descriptor has been processed by the device,
the driver polls the FIFO to see if DESC_HDR_DONE is set on a descriptor
header to confirm completion.
The current code does not make sure that the CPU gets up to date data
before reading the descriptor.
Fix this by calling dma_sync_single_for_cpu() before reading memory
written by the device.
Cc: stable@vger.kernel.org
Fixes: 58cdbc6d22 ("crypto: talitos - fix hash on SEC1.")
Signed-off-by: Paul Louvel <paul.louvel@bootlin.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a8a1f93080 upstream.
When fips_enabled=1, it seems to have been intended for one of the
algorithms defined in crypto/drbg.c to be the highest priority "stdrng"
algorithm, so that it is what is used by "stdrng" users.
However, the code only boosts the priority to 400, which is less than
the priority 500 used in drivers/crypto/caam/caamprng.c. Thus, the CAAM
RNG could be used instead.
Fix this by boosting the priority by 2000 instead of 200.
Fixes: 541af946fe ("crypto: drbg - SP800-90A Deterministic Random Bit Generator")
Cc: stable@vger.kernel.org
Signed-off-by: Eric Biggers <ebiggers@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6f49f00c98 upstream.
On 64-bit kernels, drbg_max_addtl() returns 2**35 bytes. That's too
large, for two reasons:
1. SP800-90A says the maximum limit is 2**35 *bits*, not 2**35 bytes.
So the implemented limit has confused bits and bytes.
2. When drbg_kcapi_hash() calls crypto_shash_update() on the additional
information string, the length is implicitly cast to 'unsigned int'.
That truncates the additional information string to U32_MAX bytes.
Fix the maximum additional information string length to always be
U32_MAX - 1, causing an error to be returned for any longer lengths.
Fixes: 541af946fe ("crypto: drbg - SP800-90A Deterministic Random Bit Generator")
Cc: stable@vger.kernel.org
Signed-off-by: Eric Biggers <ebiggers@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 39a31ad9e2 upstream.
drbg_ctr_generate() sometimes returns success when it fails, leaving the
output buffer uninitialized. Fix it.
Fixes: cde001e4c3 ("crypto: rng - RNGs must return 0 in success case")
Cc: stable@vger.kernel.org
Signed-off-by: Eric Biggers <ebiggers@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ed459fe319 upstream.
pcrypt installs pcrypt_aead_done() on the child AEAD request before
trying to submit it through padata. If padata_do_parallel() returns
-EBUSY, pcrypt falls back to calling the child AEAD directly.
That fallback must not keep the padata completion callback. Otherwise
an asynchronous completion runs pcrypt_aead_done() even though the
request was never enrolled in padata.
Restore the original request callback and callback data before calling
the child AEAD directly. This keeps the fallback path aligned with a
direct AEAD request while leaving the parallel path unchanged.
Fixes: 662f2f13e6 ("crypto: pcrypt - Call crypto layer directly when padata_do_parallel() return -EBUSY")
Cc: stable@kernel.org
Reported-by: Yuan Tan <yuantan098@gmail.com>
Reported-by: Yifan Wu <yifanwucs@gmail.com>
Reported-by: Juefei Pu <tomapufckgml@gmail.com>
Reported-by: Zhengchuan Liang <zcliangcn@gmail.com>
Reported-by: Xin Liu <bird@lzu.edu.cn>
Assisted-by: Codex:gpt-5.4
Signed-off-by: Ruijie Li <ruijieli51@gmail.com>
Signed-off-by: Ren Wei <n05ec@lzu.edu.cn>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 27b536a2ec upstream.
The carry flag calculation fails when r01.m_high is saturated
(0xFFFFFFFFFFFFFFFF) and addition of lower bits overflows.
The condition (r01.m_high < product.m_high) doesn't handle the case
where r01.m_high == product.m_high and an additional carry exists
from lower-bit overflow.
When commit 3c4b23901a ("crypto: ecdh - Add ECDH software support")
introduced crypto/ecc.c, it split the muladd() function in the
micro-ecc library into separate mul_64_64() and add_128_128() helpers.
It seems the check got lost in translation.
Add proper handling for this boundary by accounting for the carry
from the lower addition.
Fixes: 3c4b23901a ("crypto: ecdh - Add ECDH software support")
Signed-off-by: Anastasia Tishchenko <sv3iry@gmail.com>
Cc: stable@vger.kernel.org # v4.8+
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3f57657b6e upstream.
Use print_hex_dump_devel() for dumping sensitive key material in
*_setkey() and gen_split_key() to avoid leaking secrets at runtime when
CONFIG_DYNAMIC_DEBUG is enabled.
Fixes: 6e00550319 ("crypto: caam - print debug messages at debug level")
Cc: stable@vger.kernel.org
Signed-off-by: Thorsten Blum <thorsten.blum@linux.dev>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5fa1d6a5ec upstream.
get_symlink_chunk() and the SL handling in
parse_rock_ridge_inode_internal() walk the variable-length components of
a Rock Ridge "SL" (symbolic link) record. Each component is a two-byte
header (flags, len) followed by len bytes of text, so it occupies
slp->len + 2 bytes. Both loops read slp->len and advance to the next
component, and get_symlink_chunk() additionally does
memcpy(rpnt, slp->text, slp->len), but neither checks that the component
lies within the SL record before dereferencing it.
A crafted SL record whose component declares a len that runs past the
record (rr->len) therefore triggers an out-of-bounds read of up to 255
bytes. When the record sits at the tail of its backing buffer - for
example a small kmalloc()ed continuation block reached through a CE
record - the read crosses the allocation; get_symlink_chunk() then
copies the out-of-bounds bytes into the symlink body returned to user
space by readlink(), disclosing adjacent kernel memory.
ISO 9660 images are routinely mounted from untrusted removable media -
desktop environments auto-mount them (e.g. via udisks2) without
CAP_SYS_ADMIN - so the record contents are attacker-controlled.
Reject any component that does not fit in the remaining record bytes
before using it. In get_symlink_chunk() return NULL, like the existing
output-buffer (plimit) checks, so a malformed record makes readlink()
fail with -EIO rather than silently returning a truncated target; in
parse_rock_ridge_inode_internal() stop the inode-size walk.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable@vger.kernel.org
Suggested-by: Michael Bommarito <michael.bommarito@gmail.com>
Signed-off-by: Bryam Vargas <hexlabsecurity@proton.me>
Link: https://patch.msgid.link/20260607011823.217748-1-hexlabsecurity@proton.me
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2dc0bfd2fe upstream.
aix_partition() reads the physical volume descriptor into a fixed-size
struct pvd and then scans its physical-partition-extent array:
int numpps = be16_to_cpu(pvd->pp_count);
...
for (i = 0; i < numpps; i += 1) {
struct ppe *p = pvd->ppe + i;
...
lp_ix = be16_to_cpu(p->lp_ix);
pvd points at a single kmalloc()'d struct pvd whose ppe[] member holds a
fixed ARRAY_SIZE(pvd->ppe) (1016) entries, but the loop runs up to the
on-disk pp_count. pp_count is an unvalidated __be16 read straight from
the descriptor, so a crafted AIX image with pp_count larger than 1016
drives the loop to read pvd->ppe[i] past the end of the allocation (up
to 65535 entries, ~2 MB out of bounds).
The partition scan runs without mounting anything, when a block device
with a crafted AIX/IBM partition table appears (an attacker-supplied
image attached with losetup -P, or a device auto-scanned by udev), via
msdos_partition() -> aix_partition().
Clamp the scan to the number of entries the ppe[] array can hold.
Fixes: 6ceea22bbb ("partitions: add aix lvm partition support files")
Cc: stable@vger.kernel.org
Signed-off-by: Bryam Vargas <hexlabsecurity@proton.me>
Acked-by: Philippe De Muyter <phdm@macqel.be>
Link: https://patch.msgid.link/20260607064137.302574-1-hexlabsecurity@proton.me
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 88bac2c1a7 upstream.
When nvme_ns_head_submit_bio() remaps a bio from the multipath head to a
per-path namespace, bio_set_dev() clears BIO_REMAPPED. The remapped bio
is then resubmitted through submit_bio_noacct() which calls
bio_check_eod() because BIO_REMAPPED is not set.
This races with nvme_ns_remove() which zeroes the per-path capacity
before synchronize_srcu():
CPU 0 (IO submission)
---------------------
srcu_read_lock()
nvme_find_path() -> ns
[NVME_NS_READY is set]
CPU 1 (namespace removal)
-------------------------
clear_bit(NVME_NS_READY)
set_capacity(ns->disk, 0)
synchronize_srcu() <- blocks
CPU 0 (IO submission)
---------------------
bio_set_dev(bio, ns->disk->part0)
[clears BIO_REMAPPED]
submit_bio_noacct(bio)
-> bio_check_eod() sees capacity=0
-> bio fails with IO error
The SRCU read lock prevents synchronize_srcu() from completing, but does
not prevent set_capacity(0) from executing. The bio fails the EOD check
before it reaches the NVMe driver, so nvme_failover_req() never gets a
chance to redirect it to another path of multipath. IO errors are
reported to the application despite another path being available.
On older kernels (before commit 0b64682e78 "block: skip unnecessary
checks for split bio"), the same race was also reachable through split
remainders resubmitted via submit_bio_noacct().
Fix this by setting BIO_REMAPPED after bio_set_dev() in
nvme_ns_head_submit_bio(). This skips bio_check_eod() on the per-path
device; the EOD check already passed on the multipath head.
NVMe per-path namespace devices are always whole disks (bd_partno=0), so
the blk_partition_remap() skip also gated by BIO_REMAPPED is a no-op.
The flag does not persist across failover and cannot go stale if the
namespace geometry changes between attempts: nvme_failover_req() calls
bio_set_dev() to redirect the bio back to the multipath head, which
clears BIO_REMAPPED. When nvme_requeue_work() resubmits through
submit_bio_noacct(), bio_check_eod() runs normally against the current
capacity.
Same approach as commit 3a905c37c3 ("block: skip bio_check_eod for
partition-remapped bios").
Fixes: a7c7f7b2b6 ("nvme: use bio_set_dev to assign ->bi_bdev")
Cc: stable@vger.kernel.org
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Igor Achkinazi <igor.achkinazi@dell.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 457e32348d upstream.
When we send a message to a device that has no table, the return code was
not set. The code would return "2", which is not considered a valid return value.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
Reviewed-by: Benjamin Marzinski <bmarzins@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3ec997bd55 upstream.
udf_load_sparable_map() accepts a sparing table when
sizeof(*st) + le16_to_cpu(st->reallocationTableLen) > sb->s_blocksize
is false, i.e. it treats reallocationTableLen as a number of BYTES that
must fit in the block. But the table is walked as an array of 8-byte
sparingEntry elements:
for (i = 0; i < le16_to_cpu(st->reallocationTableLen); i++) {
struct sparingEntry *entry = &st->mapEntry[i];
... entry->origLocation ...
}
in udf_get_pblock_spar15() and udf_relocate_blocks(). A
reallocationTableLen of N therefore passes the check whenever
sizeof(*st) + N <= blocksize, yet the consumers index
sizeof(*st) + N * sizeof(struct sparingEntry) bytes -- up to ~8x the
block. On a crafted UDF image this is an out-of-bounds read in
udf_get_pblock_spar15(); udf_relocate_blocks() additionally feeds the
same length to udf_update_tag(), whose crc_itu_t() reads far past the
block, and its memmove() through st->mapEntry[] is an out-of-bounds
write.
Validate reallocationTableLen as the entry count it is, with
struct_size().
Fixes: 1df2ae31c7 ("udf: Fortify loading of sparing table")
Cc: stable@vger.kernel.org
Signed-off-by: Bryam Vargas <hexlabsecurity@proton.me>
Link: https://patch.msgid.link/20260612-b4-disp-91780c4e-v1-1-f15112ff6882@proton.me
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d8202786b3 upstream.
udf_load_vat() takes the virtual partition's start offset straight from
the on-disk VAT 2.0 header without checking it against the VAT inode
size:
map->s_type_specific.s_virtual.s_start_offset =
le16_to_cpu(vat20->lengthHeader);
map->s_type_specific.s_virtual.s_num_entries =
(sbi->s_vat_inode->i_size -
map->s_type_specific.s_virtual.s_start_offset) >> 2;
lengthHeader is a fully attacker-controlled 16-bit value. If it exceeds
the VAT inode size, the s_num_entries subtraction underflows to a huge
count, which defeats the "block > s_num_entries" bound in
udf_get_pblock_virt15(); and on the ICB-inline path that function reads
((__le32 *)(iinfo->i_data + s_start_offset))[block]
so a large s_start_offset indexes past the inode's in-ICB data. Mounting
a crafted UDF image with a virtual (VAT) partition then triggers an
out-of-bounds read.
Reject a VAT whose header length does not leave room for at least one
entry within the VAT inode.
Fixes: fa5e081563 ("udf: Handle VAT packed inside inode properly")
Cc: stable@vger.kernel.org
Signed-off-by: Bryam Vargas <hexlabsecurity@proton.me>
Link: https://patch.msgid.link/20260612-b4-disp-9a2317ee-v1-1-fefef5736154@proton.me
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5f0419457f upstream.
udf_free_blocks() checks the logical block number and count against the
partition length, but drops the extent offset from that final bound. A
crafted extent can pass the guard while logicalBlockNum + offset + count
points past the partition, which later indexes past the space bitmap
array.
A single ftruncate(2) on a file backed by such an extent reliably
panics the kernel. This is a local availability issue. On desktop
systems where UDisks/polkit allows the active user to mount removable
UDF media without CAP_SYS_ADMIN, an unprivileged local user can supply
the crafted filesystem and trigger the panic by truncating a writable
file on it. Systems that require root or CAP_SYS_ADMIN to mount the
image have a higher prerequisite.
No confidentiality or integrity impact is claimed: the reproduced
primitive is an out-of-bounds read of a bitmap pointer slot followed by
a kernel panic.
Use the already computed logicalBlockNum + offset + count value for the
partition length check. Also make load_block_bitmap() reject an
out-of-range block group before indexing s_block_bitmap[], so corrupted
callers cannot walk past the flexible array.
Fixes: 56e69e5975 ("udf: prevent integer overflow in udf_bitmap_free_blocks()")
Cc: stable@vger.kernel.org
Assisted-by: Claude:claude-opus-4-7
Signed-off-by: Michael Bommarito <michael.bommarito@gmail.com>
Link: https://patch.msgid.link/20260515142327.1120767-1-michael.bommarito@gmail.com
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 434c150752 ]
When adi,number-of-wires is absent, n_wires is left at 0. The binding
documents a default of 2 wires, matching the hardware default. However
the current-rotate validation checks n_wires == 2 || n_wires == 3, so
with n_wires = 0 the guard is bypassed and adi,current-rotate is accepted
for a 2-wire RTD.
Initialize n_wires = 2 to match the binding default and ensure the
rotation check fires correctly when the property is absent.
Fixes: f110f3188e ("iio: temperature: Add support for LTC2983")
Signed-off-by: Liviu Stan <liviu.stan@analog.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Liviu Stan <liviu.stan@analog.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 735a461d06 upstream.
In the UCSI Specification Revision 3.1 RC1, bits 32-63 of the SET_NEW_CAM
command hold the 32-bit Alternate Mode Specific (AMSpecific) field.
For DisplayPort Alternate Mode, this field must contain the full
32-bit DisplayPort configuration VDO payload that the OPM wants the
connector to operate in, rather than just the pin assignment value.
This AMSpecific value follows the DisplayPort Configurations defined
in the DisplayPort Alt Mode on USB Type-C Specification v2.1a,
Table 5-13: SOP DisplayPort Configurations.
Fixes: af8622f6a5 ("usb: typec: ucsi: Support for DisplayPort alt mode")
Cc: stable <stable@kernel.org>
Signed-off-by: Madhu M <madhu.m@intel.com>
Reviewed-by: Jameson Thies <jthies@google.com>
Reviewed-by: Andrei Kuchynski <akuchynski@chromium.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://patch.msgid.link/20260619153311.3526083-1-madhu.m@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d092d7edf8 upstream.
The existing implementation assigned these flags backwards, configuring
the partner's DisplayPort role to match the port's role instead of
complementing it.
This prevents proper configuration during DP altmode activation, often
causing `pin_assignment` to remain 0 in `dp_altmode_configure()` and
resulting in VDM negotiation failures:
[ 583.328246] typec port1.1: VDM 0xff01a150 failed
Additionally, the fix ensures that the `pin_assignment` sysfs attribute
displays the correct values.
Cc: stable <stable@kernel.org>
Fixes: af8622f6a5 ("usb: typec: ucsi: Support for DisplayPort alt mode")
Signed-off-by: Andrei Kuchynski <akuchynski@chromium.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://patch.msgid.link/20260601142837.3240207-1-akuchynski@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7b681dd5fb upstream.
In svdm_consume_modes(), the SVID value is read from pmdata->svids using
pmdata->svid_index as an array index without bounds validation:
paltmode->svid = pmdata->svids[pmdata->svid_index];
If pmdata->svid_index is driven beyond SVID_DISCOVERY_MAX (16), it results
in an out-of-bounds read of the pmdata->svids array. Because pd_mode_data
is embedded inside struct tcpm_port, indexing past svids reads into
adjacent fields. In particular:
- At index 16, it reads the altmodes count.
- At index 18 and beyond, it reads into altmode_desc[], which contains
partner-supplied SVDM Discovery Modes VDOs.
By injecting a chosen SVID into altmode_desc[0].vdo and driving svid_index
to 20, the partner can force paltmode->svid to be loaded with an arbitrary,
partner- chosen SVID, which is then registered via
typec_partner_register_altmode().
Fix this by validating that pmdata->svid_index is non-negative and strictly
less than pmdata->nsvids before accessing the pmdata->svids array inside
svdm_consume_modes().
Assisted-by: Antigravity:gemini-3.5-flash
Fixes: 4ab8c18d4d ("usb: typec: Register a device for every mode")
Cc: stable <stable@kernel.org>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: RD Babiera <rdbabiera@google.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://patch.msgid.link/20260622220803.305750-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c5371e0b91 upstream.
vep_alloc_request() wasn't initializing vrequest->udc, so cancellations
on the FunctionFS AIO path were arriving in vep_dequeue without a valid
UDC reference.
Since vrequest->udc is never actually properly used anywhere, we opt to
remove it, and update vep_dequeue to obtain a reference to the udc with
ep_to_vudc(), consistent with the other vep_ ops.
AFAICT this bug has existed for ~10 years. Seems that nobody has really
stressed the FunctionFS AIO path on usbip's vudc.
I tested this fix in a QEMU aarch64 guest driving FunctionFS endpoints
via AIO. Before the fix, running `usbip attach` from the host would
cause the guest to oops with the following backtrace:
Call trace:
vep_dequeue+0x1c/0xe4 (P)
usb_ep_dequeue+0x14/0x20
ffs_aio_cancel+0x24/0x34
__arm64_sys_io_cancel+0xb0/0x124
do_el0_svc+0x68/0x100
el0_svc+0x18/0x5c
el0t_64_sync_handler+0x98/0xdc
el0t_64_sync+0x154/0x158
Assisted-by: opencode:openai/gpt-5.5
Cc: stable <stable@kernel.org>
Fixes: b6a0ca1118 ("usbip: vudc: Add UDC specific ops")
Reviewed-by: Igor Kotrasinski <i.kotrasinsk@samsung.com>
Signed-off-by: Sam Day <me@samcday.com>
Link: https://patch.msgid.link/20260626-usbip-vudc-deque-fix-v3-1-98c2dc4d6a48@samcday.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 195e667c87 upstream.
USB devices running at SuperSpeedPlus report "10000" or "20000" in
their sysfs speed attribute. usbip currently maps only "5000" to
USB_SPEED_SUPER, so a SuperSpeedPlus device is imported as
USB_SPEED_UNKNOWN.
The attach request is then rejected by vhci_hcd:
vhci_hcd: Failed attach request for unsupported USB speed: UNKNOWN
Map the SuperSpeedPlus sysfs speed values to USB_SPEED_SUPER_PLUS, use
the SuperSpeed VHCI hub for SuperSpeedPlus devices, and recognize the
gadget current_speed string used by the kernel.
Fixes: b2316645ca ("usb: show speed "10000" in sysfs for USB 3.1 SuperSpeedPlus devices")
Cc: stable <stable@kernel.org>
Signed-off-by: Yichong Chen <chenyichong@uniontech.com>
Reviewed-by: Shuah Khan <skhan@linuxfoundation.org>
Link: https://patch.msgid.link/00C828F338E43447+20260617020613.199086-1-chenyichong@uniontech.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5fc3f333c0 upstream.
Commit 1892bf9067 ("USB: usb-storage: Fix use of bitfields for
hardware data in ene_ub6250.c") converted the media status fields from
bitfields to bit masks.
The original ene_transport() test called ene_init() only when neither
media type was ready:
!(sd_ready || ms_ready)
The converted test became:
!sd_ready || ms_ready
This is not equivalent. Restore the original semantics by testing that
both ready bits are clear before calling ene_init().
Fixes: 1892bf9067 ("USB: usb-storage: Fix use of bitfields for hardware data in ene_ub6250.c")
Cc: stable <stable@kernel.org>
Signed-off-by: Xu Rao <raoxu@uniontech.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://patch.msgid.link/F42641386E32404F+20260626070607.4119527-1-raoxu@uniontech.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8af6812795 upstream.
The allocated device name is never freed on early ULPI device
registration failures.
Fix this by initialising the device structure earlier and releasing the
initial reference whenever registration fails.
Fixes: 289fcff4bc ("usb: add bus type for USB ULPI")
Cc: stable <stable@kernel.org>
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://patch.msgid.link/20260608145803.69360-1-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 24ca1fea8f upstream.
The digi_write_inb_command() is supposed to wait for the write urb to
become available or return an error, but instead it updates the transfer
buffer and tries to resubmit the urb on timeout.
To make things worse, for commands like break control where no timeout
is used, the driver would corrupt the urb immediately due to a broken
jiffies comparison (on 32-bit machines this takes five minutes of uptime
to trigger due to INITIAL_JIFFIES).
Fix this by adding the missing return on timeout and waiting
indefinitely when no timeout has been specified as intended.
This issue was (sort of) flagged by Sashiko when reviewing an unrelated
change to the driver.
Link: https://sashiko.dev/#/patchset/20260610132232.356139-1-johan%40kernel.org?part=11
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable@vger.kernel.org
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5c1ea24b53 upstream.
If submitting the OOB write urb fails persistently (e.g if the device is
being disconnected) the driver would loop indefinitely with interrupts
disabled.
Check for urb submission errors when sending OOB commands to avoid
hanging if, for example, open(), set_termios() or close() races with a
physical disconnect.
This is issue was flagged by Sashiko when reviewing an unrelated change
to the driver.
Link: https://sashiko.dev/#/patchset/20260610132232.356139-1-johan%40kernel.org?part=1
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable@vger.kernel.org
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 83a3dfc018 upstream.
If the port is closed while throttled, the read urb is never resubmitted
and the port will not receive any further data until the device is
reconnected (or the driver is rebound).
Clear the throttle flags and submit the urb if needed when opening the
port.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6bfc8d01ac upstream.
The write() callback is supposed to return the number of characters
accepted or a negative errno. Since the addition of write fifo support
the keyspan_pda implementation will however return the number characters
submitted to the device if the write urb is not already in use. If this
number is larger than the number of characters passed to write(), the
line discipline continues writing data from beyond the tty write buffer.
Fix the information leak by making sure that keyspan_pda_write_start()
returns zero on success as intended.
Fixes: 034e38e8f6 ("USB: serial: keyspan_pda: add write-fifo support")
Cc: stable@vger.kernel.org # 5.11
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0bddda5a11 upstream.
mtu3_gadget_queue() maps the request before checking whether
the QMU GPD ring can accept another transfer. the request is
returned with -EAGAIN before it is linked on the endpoint
request list if mtu3_prepare_transfer() fails.
Normal completion and dequeue paths unmap requests from
mtu3_req_complete(), but this error path never reaches that
helper, so the DMA mapping is left active. Unmap the request
before returning from the failed queue path.
Fixes: df2069acb0 ("usb: Add MediaTek USB3 DRD driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Haoxiang Li <haoxiang_li2024@163.com>
Link: https://patch.msgid.link/20260623093325.2105323-1-haoxiang_li2024@163.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b4ecbdc4f8 upstream.
uss720_probe() registers a parport before reading the 1284 register used
to detect unsupported Belkin F5U002 adapters. If get_1284_register()
fails, the error path drops the driver private data and the USB device
reference, but leaves the parport device registered.
Leaving the port registered is more than a private allocation leak:
parport_register_port() has already reserved a parport number and
registered the parport bus device, while pp->private_data still points at
the private data that the common error path is about to release.
Undo the pre-announce registration in the get_1284_register() failure
branch before jumping to the common private-data cleanup path. Clear
priv->pp first, matching the disconnect path and avoiding a stale pointer
in the private data.
This issue was identified during our ongoing static-analysis research while
reviewing kernel code.
Fixes: 3295f1b866 ("usb: misc: uss720: check for incompatible versions of the Belkin F5U002")
Cc: stable <stable@kernel.org>
Co-developed-by: Ijae Kim <ae878000@gmail.com>
Signed-off-by: Ijae Kim <ae878000@gmail.com>
Signed-off-by: Myeonghun Pak <mhun512@gmail.com>
Reviewed-by: Alex Henrie <alexhenrie24@gmail.com>
Link: https://patch.msgid.link/20260706151049.63470-1-mhun512@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2c00e09e3f upstream.
usb_stor_adjust_quirks() parses the usb-storage.quirks module
parameter into a new flag set and then applies it with the quirk
mask to override built-in flags.
The mask is meant to cover the flags that can be overridden by
the module parameter. The 'k' quirk character sets US_FL_NO_SAME,
but US_FL_NO_SAME is not included in the mask.
As a result, the module parameter can set US_FL_NO_SAME, but it
cannot clear a built-in US_FL_NO_SAME flag by providing an override
entry that omits 'k'.
Add US_FL_NO_SAME to the mask so that the module parameter can
override it in the same way as the other supported flags.
Fixes: 8010622c86 ("USB: UAS: introduce a quirk to set no_write_same")
Cc: stable <stable@kernel.org>
Signed-off-by: Xu Rao <raoxu@uniontech.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://patch.msgid.link/3BCE5880F9A45C2E+20260602053842.2920137-1-raoxu@uniontech.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4e8ba83ac4 upstream.
sl811h_probe() enables the HCD controller device as a wakeup source after
usb_add_hcd() succeeds, but sl811h_remove() removes the HCD and releases
the driver resources without disabling that wakeup source.
Disable controller wakeup after usb_remove_hcd() and before usb_put_hcd()
so the wakeup source object is detached while the controller device pointer
is still available.
This issue was identified during our ongoing static-analysis research while
reviewing kernel code.
Fixes: 3c9740a117 ("usb: hcd: move controller wakeup setting initialization to individual driver")
Cc: stable <stable@kernel.org>
Co-developed-by: Ijae Kim <ae878000@gmail.com>
Signed-off-by: Ijae Kim <ae878000@gmail.com>
Signed-off-by: Myeonghun Pak <mhun512@gmail.com>
Link: https://patch.msgid.link/20260701121625.96815-1-mhun512@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 62fc8eb1b1 upstream.
mutex_unlock() may access the mutex structure after releasing the lock
and therefore cannot be used to manage lifetime of objects directly
(unlike spinlocks and refcounts). [1][2]
Use a kref to release the driver data to avoid use-after-free in
mutex_unlock() when release() races with disconnect().
[1] a51749ab34 ("locking/mutex: Document that mutex_unlock() is
non-atomic")
[2] 2b9d9e0a9b ("locking/mutex: Clarify that mutex_unlock(), and most
other sleeping locks, can still use the lock object
after it's unlocked")
Fixes: 18bcbcfe9c ("USB: misc: legousbtower: semaphore to mutex")
Cc: stable <stable@kernel.org>
Cc: Daniel Walker <dwalker@mvista.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://patch.msgid.link/20260622152612.116422-5-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fc59178778 upstream.
The Samsung T5 EVO Portable SSD (04e8:6200) exhibit two forms of
link instability when USB Link Power Management is enabled:
1. The units fail to initialize properly on first detection,
resulting in a lockup in the drive where it must be power cycled
or the kernel will not recognize the presence of the device.
2. If used for sustained operations (small amounts of continuous
data are transferred to the unit) then the unit will "hiccup"
after roughly 8 hours of use and will disconnect and reconnect.
This has a certain probability of triggering the first issue,
but also causes mount points to become invalid since the device
gets issued a new letter.
Signed-off-by: Erich E. Hoover <erich.e.hoover@gmail.com>
Cc: stable <stable@kernel.org>
Link: https://patch.msgid.link/20260602204508.48856-1-erich.e.hoover@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 19bdfc7b3c upstream.
mutex_unlock() may access the mutex structure after releasing the lock
and therefore cannot be used to manage lifetime of objects directly
(unlike spinlocks and refcounts). [1][2]
Use a kref to release the driver data to avoid use-after-free in
mutex_unlock() when release() races with disconnect().
[1] a51749ab34 ("locking/mutex: Document that mutex_unlock() is
non-atomic")
[2] 2b9d9e0a9b ("locking/mutex: Clarify that mutex_unlock(), and most
other sleeping locks, can still use the lock object
after it's unlocked")
Fixes: ce0d7d3f57 ("usb: ldusb: ld_usb semaphore to mutex")
Cc: stable <stable@kernel.org>
Cc: Daniel Walker <dwalker@mvista.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://patch.msgid.link/20260622152612.116422-4-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ff002c153f upstream.
mutex_unlock() may access the mutex structure after releasing the lock
and therefore cannot be used to manage lifetime of objects directly
(unlike spinlocks and refcounts). [1][2]
Use a kref to release the driver data to avoid use-after-free in
mutex_unlock() when release() races with disconnect().
[1] a51749ab34 ("locking/mutex: Document that mutex_unlock() is
non-atomic")
[2] 2b9d9e0a9b ("locking/mutex: Clarify that mutex_unlock(), and most
other sleeping locks, can still use the lock object
after it's unlocked")
Fixes: 54d2bc068f ("USB: fix locking in idmouse")
Cc: stable@vger.kernel.org # 2.6.24
Cc: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://patch.msgid.link/20260622152612.116422-3-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 67e511d298 upstream.
The udc structure acts as the management structure for the gadget,
but their lifecycles are decoupled. A race condition exists where
usb_del_gadget() frees the udc memory (e.g., via mode-switch work)
while gadget_match_driver() concurrently accesses the freed udc memory
(e.g., via configfs), causing a Use-After-Free (UAF) that triggers a
NULL pointer dereference when the freed memory is zeroed:
[39430.908615][ T1171] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000
[39430.911397][ T1171] pc : __pi_strcmp+0x20/0x140
[39430.911441][ T1171] lr : gadget_match_driver+0x34/0x60
...
[39430.911890][ T1171] usb_gadget_register_driver_owner+0x50/0xf8
[39430.911910][ T1171] gadget_dev_desc_UDC_store+0xf4/0x140
[39430.931308][ T1171] configfs_write_iter+0xec/0x134
[39430.957058][ T1171] Workqueue: events_freezable __dwc3_set_mode
[39430.957287][ T1171] dwc3_gadget_exit+0x34/0x8c
[39430.957304][ T1171] __dwc3_set_mode+0xc0/0x664
Fix this by ensuring the udc structure remains allocated until the
gadget is released. To achieve this, introduce a new
usb_gadget_release() routine to the core. When the gadget is added,
usb_add_gadget() stores the gadget's release routine in the udc
structure and takes a reference to the udc. When the gadget is
released, usb_gadget_release() drops the reference to the udc and
then calls the gadget's release routine.
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Jimmy Hu <hhhuuu@google.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://patch.msgid.link/20260625073705.803880-1-hhhuuu@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
