commit 1bd8d6cd3e upstream.
In the ext4 implementations of SEEK_HOLE and SEEK_DATA, make sure we
return -ENXIO for negative offsets instead of banging around inside
the extent code and returning -EFSCORRUPTED.
Reported-by: Mateusz S <muttdini@gmail.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 39efc7cc7c upstream.
As the association status changes the driver needs to configure the
hardware. This is done based on information in the "sta" acquired by
ieee80211_find_sta(), which requires the caller to ensure that the "sta"
is valid while its being used; generally by entering an rcu read
section.
But the operations acting on the "sta" has to communicate with the
firmware and may therefor sleep, resulting in the following report:
[ 31.418190] BUG: sleeping function called from invalid context at
kernel/locking/mutex.c:238
[ 31.425919] in_atomic(): 0, irqs_disabled(): 0, pid: 34, name:
kworker/u8:1
[ 31.434609] CPU: 0 PID: 34 Comm: kworker/u8:1 Tainted: G W
4.12.0-rc4-next-20170607+ #993
[ 31.441002] Hardware name: Qualcomm Technologies, Inc. APQ 8016 SBC
(DT)
[ 31.450380] Workqueue: phy0 ieee80211_iface_work
[ 31.457226] Call trace:
[ 31.461830] [<ffffff8008088c58>] dump_backtrace+0x0/0x260
[ 31.464004] [<ffffff8008088f7c>] show_stack+0x14/0x20
[ 31.469557] [<ffffff8008392e70>] dump_stack+0x98/0xb8
[ 31.474592] [<ffffff80080e4330>] ___might_sleep+0xf0/0x118
[ 31.479626] [<ffffff80080e43a8>] __might_sleep+0x50/0x88
[ 31.485010] [<ffffff80088ff9a4>] mutex_lock+0x24/0x60
[ 31.490479] [<ffffff8008595c38>] wcn36xx_smd_set_link_st+0x30/0x130
[ 31.495428] [<ffffff8008591ed8>] wcn36xx_bss_info_changed+0x148/0x448
[ 31.501504] [<ffffff80088ab3c4>]
ieee80211_bss_info_change_notify+0xbc/0x118
[ 31.508102] [<ffffff80088f841c>] ieee80211_assoc_success+0x664/0x7f8
[ 31.515220] [<ffffff80088e13d4>]
ieee80211_rx_mgmt_assoc_resp+0x144/0x2d8
[ 31.521555] [<ffffff80088e1e20>]
ieee80211_sta_rx_queued_mgmt+0x190/0x698
[ 31.528239] [<ffffff80088bc44c>] ieee80211_iface_work+0x234/0x368
[ 31.535011] [<ffffff80080d81ac>] process_one_work+0x1cc/0x340
[ 31.541086] [<ffffff80080d8368>] worker_thread+0x48/0x430
[ 31.546814] [<ffffff80080de448>] kthread+0x108/0x138
[ 31.552195] [<ffffff8008082ec0>] ret_from_fork+0x10/0x50
In order to ensure that the "sta" remains alive (and consistent) for the
duration of bss_info_changed() mutual exclusion has to be ensured with
sta_remove().
This is done by introducing a mutex to cover firmware configuration
changes, which is made to also ensure mutual exclusion between other
operations changing the state or configuration of the firmware. With
this we can drop the rcu read lock.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 91a024e803 upstream.
The original patch from Tony uses standby mode bit inverted, which is
not correct. This fixes all instances in the driver code for get & set
mode. This did not yet make problems, since mode has not been changed
by any mainline driver so far.
Fixes: 0ad4c07edd ("regulator: cpcap: Add basic regulator support")
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixed differently upstream as commit 2d97591ef4 ("crypto: af_alg - consolidation of duplicate code")
The SGL is MAX_SGL_ENTS + 1 in size. The last SG entry is used for the
chaining and is properly updated with the sg_chain invocation. During
the filling-in of the initial SG entries, sg_mark_end is called for each
SG entry. This is appropriate as long as no additional SGL is chained
with the current SGL. However, when a new SGL is chained and the last
SG entry is updated with sg_chain, the last but one entry still contains
the end marker from the sg_mark_end. This end marker must be removed as
otherwise a walk of the chained SGLs will cause a NULL pointer
dereference at the last but one SG entry, because sg_next will return
NULL.
The patch only applies to all kernels up to and including 4.13. The
patch 2d97591ef4 added to 4.14-rc1
introduced a complete new code base which addresses this bug in
a different way. Yet, that patch is too invasive for stable kernels
and was therefore not marked for stable.
Fixes: 8ff590903d ("crypto: algif_skcipher - User-space interface for skcipher operations")
Signed-off-by: Stephan Mueller <smueller@chronox.de>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a68a193805 upstream.
caam/qi needs a fix similar to what was done for caam/jr in
commit "crypto: caam/qi - properly set IV after {en,de}crypt",
to allow for ablkcipher/skcipher chunking/streaming.
Fixes: b189817cf7 ("crypto: caam/qi - add ablkcipher and authenc algorithms")
Suggested-by: David Gstir <david@sigma-star.at>
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3c08377262 upstream.
Due to the use of per-CPU buffers, scomp_acomp_comp_decomp() executes
with preemption disabled, and so whether the CRYPTO_TFM_REQ_MAY_SLEEP
flag is set is irrelevant, since we cannot sleep anyway. So disregard
the flag, and use GFP_ATOMIC unconditionally.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e652399edb upstream.
Version 5 CCPs have some new requirements for XTS-AES: the type field
must be specified, and the key requires 512 bits, with each part
occupying 256 bits and padded with zeroes.
Signed-off-by: Gary R Hook <ghook@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e604f1cb85 upstream.
commit 6807c84652 ("x86: Enable KASLR by default") enables KASLR
by default on x86. While KASLR will confuse gdb which resolve kernel
symbol address from symbol table of vmlinux. We should turn off KASLR for
kernel debugging.
Signed-off-by: Zhouyi Zhou <zhouzhouyi@gmail.com>
Reviewed-by: Kieran Bingham <kbingham@kernel.org>
Acked-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Cc: Natale Patriciello <natale.patriciello@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2cfa58259f upstream.
Implement fused multiply-add with correct accuracy.
Fused multiply-add operation has better accuracy than respective
sequential execution of multiply and add operations applied on the
same inputs. This is because accuracy errors accumulate in latter
case.
This patch implements fused multiply-add with the same accuracy
as it is implemented in hardware, using 128-bit intermediate
calculations.
One test case example (raw bits) that this patch fixes:
MADDF.D fd,fs,ft:
fd = 0x00000ca000000000
fs = ft = 0x3f40624dd2f1a9fc
Fixes: e24c3bec3e ("MIPS: math-emu: Add support for the MIPS R6 MADDF FPU instruction")
Fixes: 83d43305a1 ("MIPS: math-emu: Add support for the MIPS R6 MSUBF FPU instruction")
Signed-off-by: Douglas Leung <douglas.leung@imgtec.com>
Signed-off-by: Miodrag Dinic <miodrag.dinic@imgtec.com>
Signed-off-by: Goran Ferenc <goran.ferenc@imgtec.com>
Signed-off-by: Aleksandar Markovic <aleksandar.markovic@imgtec.com>
Cc: Douglas Leung <douglas.leung@imgtec.com>
Cc: Bo Hu <bohu@google.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Jin Qian <jinqian@google.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Petar Jovanovic <petar.jovanovic@imgtec.com>
Cc: Raghu Gandham <raghu.gandham@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/16891/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b3b8e1eb27 upstream.
Implement fused multiply-add with correct accuracy.
Fused multiply-add operation has better accuracy than respective
sequential execution of multiply and add operations applied on the
same inputs. This is because accuracy errors accumulate in latter
case.
This patch implements fused multiply-add with the same accuracy
as it is implemented in hardware, using 64-bit intermediate
calculations.
One test case example (raw bits) that this patch fixes:
MADDF.S fd,fs,ft:
fd = 0x22575225
fs = ft = 0x3727c5ac
Fixes: e24c3bec3e ("MIPS: math-emu: Add support for the MIPS R6 MADDF FPU instruction")
Fixes: 83d43305a1 ("MIPS: math-emu: Add support for the MIPS R6 MSUBF FPU instruction")
Signed-off-by: Douglas Leung <douglas.leung@imgtec.com>
Signed-off-by: Miodrag Dinic <miodrag.dinic@imgtec.com>
Signed-off-by: Goran Ferenc <goran.ferenc@imgtec.com>
Signed-off-by: Aleksandar Markovic <aleksandar.markovic@imgtec.com>
Cc: Douglas Leung <douglas.leung@imgtec.com>
Cc: Bo Hu <bohu@google.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Jin Qian <jinqian@google.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Petar Jovanovic <petar.jovanovic@imgtec.com>
Cc: Raghu Gandham <raghu.gandham@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/16890/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ae11c06199 upstream.
Fix definition and usage of "maddf_flags" enumeration. Avoid duplicate
definition and apply more common capitalization.
This patch does not change any scenario. It just makes MADDF and
MSUBF emulation code more readable and easier to maintain, and
hopefully prevents future bugs as well.
Signed-off-by: Miodrag Dinic <miodrag.dinic@imgtec.com>
Signed-off-by: Goran Ferenc <goran.ferenc@imgtec.com>
Signed-off-by: Aleksandar Markovic <aleksandar.markovic@imgtec.com>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Cc: Bo Hu <bohu@google.com>
Cc: Douglas Leung <douglas.leung@imgtec.com>
Cc: Jin Qian <jinqian@google.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Petar Jovanovic <petar.jovanovic@imgtec.com>
Cc: Raghu Gandham <raghu.gandham@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/16889/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7cf64ce4d3 upstream.
Fix the cases of <MADDF|MSUBF>.<D|S> when any of two multiplicands is
+0 or -0, and the third input is also +0 or -0. Depending on the signs
of inputs, certain special cases must be handled.
A relevant example:
MADDF.S fd,fs,ft:
If fs contains +0.0, ft contains -0.0, and fd contains 0.0, fd is
going to contain +0.0 (without this patch, it used to contain -0.0).
Fixes: e24c3bec3e ("MIPS: math-emu: Add support for the MIPS R6 MADDF FPU instruction")
Fixes: 83d43305a1 ("MIPS: math-emu: Add support for the MIPS R6 MSUBF FPU instruction")
Signed-off-by: Miodrag Dinic <miodrag.dinic@imgtec.com>
Signed-off-by: Goran Ferenc <goran.ferenc@imgtec.com>
Signed-off-by: Aleksandar Markovic <aleksandar.markovic@imgtec.com>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Cc: Bo Hu <bohu@google.com>
Cc: Douglas Leung <douglas.leung@imgtec.com>
Cc: Jin Qian <jinqian@google.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Petar Jovanovic <petar.jovanovic@imgtec.com>
Cc: Raghu Gandham <raghu.gandham@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/16888/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0c64fe6348 upstream.
Fix the cases of <MADDF|MSUBF>.<D|S> when any of two multiplicands is
infinity. The correct behavior in such cases is affected by the nature
of third input. Cases of addition of infinities with opposite signs
and subtraction of infinities with same signs may arise and must be
handles separately. Also, the value od flags argument (that determines
whether the instruction is MADDF or MSUBF) affects the outcome.
Relevant examples:
MADDF.S fd,fs,ft:
If fs contains +inf, ft contains +inf, and fd contains -inf, fd is
going to contain indef (without this patch, it used to contain
-inf).
MSUBF.S fd,fs,ft:
If fs contains +inf, ft contains 1.0, and fd contains +0.0, fd is
going to contain -inf (without this patch, it used to contain +inf).
Fixes: e24c3bec3e ("MIPS: math-emu: Add support for the MIPS R6 MADDF FPU instruction")
Fixes: 83d43305a1 ("MIPS: math-emu: Add support for the MIPS R6 MSUBF FPU instruction")
Signed-off-by: Douglas Leung <douglas.leung@imgtec.com>
Signed-off-by: Miodrag Dinic <miodrag.dinic@imgtec.com>
Signed-off-by: Goran Ferenc <goran.ferenc@imgtec.com>
Signed-off-by: Aleksandar Markovic <aleksandar.markovic@imgtec.com>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Cc: Douglas Leung <douglas.leung@imgtec.com>
Cc: Bo Hu <bohu@google.com>
Cc: Jin Qian <jinqian@google.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Petar Jovanovic <petar.jovanovic@imgtec.com>
Cc: Raghu Gandham <raghu.gandham@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/16887/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e840be6e70 upstream.
Fix the cases of <MADDF|MSUBF>.<D|S> when any of three inputs is any
NaN. Correct behavior of <MADDF|MSUBF>.<D|S> fd, fs, ft is following:
- if any of inputs is sNaN, return a sNaN using following rules: if
only one input is sNaN, return that one; if more than one input is
sNaN, order of precedence for return value is fd, fs, ft
- if no input is sNaN, but at least one of inputs is qNaN, return a
qNaN using following rules: if only one input is qNaN, return that
one; if more than one input is qNaN, order of precedence for
return value is fd, fs, ft
The previous code contained correct handling of some above cases, but
not all. Also, such handling was scattered into various cases of
"switch (CLPAIR(xc, yc))" statement, and elsewhere. With this patch,
this logic is placed in one place, and "switch (CLPAIR(xc, yc))" is
significantly simplified.
A relevant example:
MADDF.S fd,fs,ft:
If fs contains qNaN1, ft contains qNaN2, and fd contains qNaN3, fd
is going to contain qNaN3 (without this patch, it used to contain
qNaN1).
Fixes: e24c3bec3e ("MIPS: math-emu: Add support for the MIPS R6 MADDF FPU instruction")
Fixes: 83d43305a1 ("MIPS: math-emu: Add support for the MIPS R6 MSUBF FPU instruction")
Signed-off-by: Miodrag Dinic <miodrag.dinic@imgtec.com>
Signed-off-by: Goran Ferenc <goran.ferenc@imgtec.com>
Signed-off-by: Aleksandar Markovic <aleksandar.markovic@imgtec.com>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Cc: Bo Hu <bohu@google.com>
Cc: Douglas Leung <douglas.leung@imgtec.com>
Cc: Jin Qian <jinqian@google.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Petar Jovanovic <petar.jovanovic@imgtec.com>
Cc: Raghu Gandham <raghu.gandham@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/16886/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 304bfe473e upstream.
Fix following special cases for MINA>.<D|S>:
- if one of the inputs is zero, and the other is subnormal, normal,
or infinity, the value of the former should be returned (that is,
a zero).
- if one of the inputs is infinity, and the other input is normal,
or subnormal, the value of the latter should be returned.
The previous implementation's logic for such cases was incorrect - it
appears as if it implements MAXA, and not MINA instruction.
A relevant example:
MINA.S fd,fs,ft:
If fs contains 100.0, and ft contains 0.0, fd is going to contain
0.0 (without this patch, it used to contain 100.0).
Fixes: a79f5f9ba5 ("MIPS: math-emu: Add support for the MIPS R6 MAX{, A} FPU instruction")
Fixes: 4e9561b20e ("MIPS: math-emu: Add support for the MIPS R6 MIN{, A} FPU instruction")
Signed-off-by: Miodrag Dinic <miodrag.dinic@imgtec.com>
Signed-off-by: Goran Ferenc <goran.ferenc@imgtec.com>
Signed-off-by: Aleksandar Markovic <aleksandar.markovic@imgtec.com>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Cc: Bo Hu <bohu@google.com>
Cc: Douglas Leung <douglas.leung@imgtec.com>
Cc: Jin Qian <jinqian@google.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Petar Jovanovic <petar.jovanovic@imgtec.com>
Cc: Raghu Gandham <raghu.gandham@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/16885/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3444c4eb53 upstream.
Fix the value returned by <MAXA|MINA>.<D|S> fd,fs,ft, if both inputs
are infinite. The previous implementation returned always the value
contained in ft in such cases. The correct behavior is specified
in Mips instruction set manual and is as follows:
fs ft MAXA MINA
---------------------------------
inf inf inf inf
inf -inf inf -inf
-inf inf inf -inf
-inf -inf -inf -inf
A relevant example:
MAXA.S fd,fs,ft:
If fs contains +inf, and ft contains -inf, fd is going to contain
+inf (without this patch, it used to contain -inf).
Fixes: a79f5f9ba5 ("MIPS: math-emu: Add support for the MIPS R6 MAX{, A} FPU instruction")
Fixes: 4e9561b20e ("MIPS: math-emu: Add support for the MIPS R6 MIN{, A} FPU instruction")
Signed-off-by: Miodrag Dinic <miodrag.dinic@imgtec.com>
Signed-off-by: Goran Ferenc <goran.ferenc@imgtec.com>
Signed-off-by: Aleksandar Markovic <aleksandar.markovic@imgtec.com>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Cc: Bo Hu <bohu@google.com>
Cc: Douglas Leung <douglas.leung@imgtec.com>
Cc: Jin Qian <jinqian@google.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Petar Jovanovic <petar.jovanovic@imgtec.com>
Cc: Raghu Gandham <raghu.gandham@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/16884/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1a41b3b441 upstream.
Fix the value returned by <MAXA|MINA>.<D|S>, if the inputs are normal
fp numbers of the same absolute value, but opposite signs.
A relevant example:
MAXA.S fd,fs,ft:
If fs contains -3.0, and ft contains +3.0, fd is going to contain
+3.0 (without this patch, it used to contain -3.0).
Fixes: a79f5f9ba5 ("MIPS: math-emu: Add support for the MIPS R6 MAX{, A} FPU instruction")
Fixes: 4e9561b20e ("MIPS: math-emu: Add support for the MIPS R6 MIN{, A} FPU instruction")
Signed-off-by: Miodrag Dinic <miodrag.dinic@imgtec.com>
Signed-off-by: Goran Ferenc <goran.ferenc@imgtec.com>
Signed-off-by: Aleksandar Markovic <aleksandar.markovic@imgtec.com>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Cc: Bo Hu <bohu@google.com>
Cc: Douglas Leung <douglas.leung@imgtec.com>
Cc: Jin Qian <jinqian@google.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Petar Jovanovic <petar.jovanovic@imgtec.com>
Cc: Raghu Gandham <raghu.gandham@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/16883/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aabf5cf02e upstream.
Fix the value returned by <MAX|MIN>.<D|S>, if both inputs are negative
normal fp numbers. The previous logic did not take into account that
if both inputs have the same sign, there should be separate treatment
of the cases when both inputs are negative and when both inputs are
positive.
A relevant example:
MAX.S fd,fs,ft:
If fs contains -5.0, and ft contains -7.0, fd is going to contain
-5.0 (without this patch, it used to contain -7.0).
Fixes: a79f5f9ba5 ("MIPS: math-emu: Add support for the MIPS R6 MAX{, A} FPU instruction")
Fixes: 4e9561b20e ("MIPS: math-emu: Add support for the MIPS R6 MIN{, A} FPU instruction")
Signed-off-by: Miodrag Dinic <miodrag.dinic@imgtec.com>
Signed-off-by: Goran Ferenc <goran.ferenc@imgtec.com>
Signed-off-by: Aleksandar Markovic <aleksandar.markovic@imgtec.com>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Cc: Bo Hu <bohu@google.com>
Cc: Douglas Leung <douglas.leung@imgtec.com>
Cc: Jin Qian <jinqian@google.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Petar Jovanovic <petar.jovanovic@imgtec.com>
Cc: Raghu Gandham <raghu.gandham@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/16882/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 15560a58bf upstream.
Fix the value returned by <MAX|MAXA|MIN|MINA>.<D|S>, if both inputs
are zeros. The right behavior in such cases is stated in instruction
reference manual and is as follows:
fs ft MAX MIN MAXA MINA
---------------------------------------------
0 0 0 0 0 0
0 -0 0 -0 0 -0
-0 0 0 -0 0 -0
-0 -0 -0 -0 -0 -0
Prior to this patch, some of the above cases were yielding correct
results. However, for the sake of code consistency, all such cases
are rewritten in this patch.
A relevant example:
MAX.S fd,fs,ft:
If fs contains +0.0, and ft contains -0.0, fd is going to contain
+0.0 (without this patch, it used to contain -0.0).
Fixes: a79f5f9ba5 ("MIPS: math-emu: Add support for the MIPS R6 MAX{, A} FPU instruction")
Fixes: 4e9561b20e ("MIPS: math-emu: Add support for the MIPS R6 MIN{, A} FPU instruction")
Signed-off-by: Miodrag Dinic <miodrag.dinic@imgtec.com>
Signed-off-by: Goran Ferenc <goran.ferenc@imgtec.com>
Signed-off-by: Aleksandar Markovic <aleksandar.markovic@imgtec.com>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Cc: Bo Hu <bohu@google.com>
Cc: Douglas Leung <douglas.leung@imgtec.com>
Cc: Jin Qian <jinqian@google.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Petar Jovanovic <petar.jovanovic@imgtec.com>
Cc: Raghu Gandham <raghu.gandham@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/16881/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e78bf0dc47 upstream.
Fix the value returned by <MAX|MAXA|MIN|MINA>.<D|S> fd,fs,ft, if both
inputs are quiet NaNs. The <MAX|MAXA|MIN|MINA>.<D|S> specifications
state that the returned value in such cases should be the quiet NaN
contained in register fs.
A relevant example:
MAX.S fd,fs,ft:
If fs contains qNaN1, and ft contains qNaN2, fd is going to contain
qNaN1 (without this patch, it used to contain qNaN2).
Fixes: a79f5f9ba5 ("MIPS: math-emu: Add support for the MIPS R6 MAX{, A} FPU instruction")
Fixes: 4e9561b20e ("MIPS: math-emu: Add support for the MIPS R6 MIN{, A} FPU instruction")
Signed-off-by: Miodrag Dinic <miodrag.dinic@imgtec.com>
Signed-off-by: Goran Ferenc <goran.ferenc@imgtec.com>
Signed-off-by: Aleksandar Markovic <aleksandar.markovic@imgtec.com>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Cc: Bo Hu <bohu@google.com>
Cc: Douglas Leung <douglas.leung@imgtec.com>
Cc: Jin Qian <jinqian@google.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Petar Jovanovic <petar.jovanovic@imgtec.com>
Cc: Raghu Gandham <raghu.gandham@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/16880/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 697c5d8a36 upstream.
Similar to other Gigabyte laptops, the touchpad on P57 requires a
keyboard reset to detect Elantech touchpad correctly.
BugLink: https://bugs.launchpad.net/bugs/1594214
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 79d2c8bede upstream.
The touchpad in the Asus laptop models X505BA/BP and X542BA/BP is
unresponsive after suspend/resume. The following error appears during
resume:
i2c_hid i2c-ELAN1300:00: failed to reset device.
The problem here is that i2c_hid does not notice the interrupt being
generated at this point, because the GPIO is no longer configured
for interrupts.
Fix this by saving pinctrl-amd pin registers during suspend and
restoring them at resume time.
Based on code from pinctrl-intel.
Signed-off-by: Daniel Drake <drake@endlessm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cee7413d84 upstream.
After commit 8b1bd11c1f ("pinctrl: samsung: Add the support the
multiple IORESOURCE_MEM for one pin-bank"), the S3C24xx (and probably
S3C64xx as well) fails:
Unable to handle kernel NULL pointer dereference at virtual address 000000a8
...
(s3c24xx_demux_eint4_7) from [<c004469c>] (__handle_domain_irq+0x6c/0xcc)
(__handle_domain_irq) from [<c0009444>] (s3c24xx_handle_irq+0x6c/0x12c)
(s3c24xx_handle_irq) from [<c000e5fc>] (__irq_svc+0x5c/0x78)
Mentioned commit moved the pointer to controller's base IO memory address
from each controller's driver data (samsung_pinctrl_drv_data) to per-bank
structure (samsung_pin_bank). The external interrupt demux
handlers (s3c24xx_demux_eint()) tried to get this base address from opaque
pointer stored under irq_chip data:
struct irq_data *irqd = irq_desc_get_irq_data(desc);
struct samsung_pin_bank *bank = irq_data_get_irq_chip_data(irqd);
...
pend = readl(bank->eint_base + EINTPEND_REG);
which is wrong because this is hardware irq and it bank was never set
for this irq_chip.
For S3C24xx and S3C64xx, this partially reverts mentioned commit by
bringing back the virt_base stored under each controller's driver data
(samsung_pinctrl_drv_data). This virt_base address will be now
duplicated:
- samsung_pinctrl_drv_data->virt_base: used on S3C24xx and S3C64xx,
- samsung_pin_bank->pctl_base: used on Exynos.
Fixes: 8b1bd11c1f ("pinctrl: samsung: Add the support the multiple IORESOURCE_MEM for one pin-bank")
Cc: Sergio Prado <sergio.prado@e-labworks.com>
Reported-by: Sergio Prado <sergio.prado@e-labworks.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Lihua Yao <ylhuajnu@163.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit af0b0baa89 upstream.
When setting the pin function for external interrupts, the driver used
wrong IO memory address base. The pin function register is always under
pctl_base, not the eint_base.
By updating wrong register, the external interrupts for chosen GPIO
would not work at all and some other GPIO might be configured to wrong
value. For example on Exynos5433-based boards, the external interrupts
for gpf{1-5}-X GPIOs should not work at all (driver toggled reserved
registers from ALIVE bank instead).
Platforms other than Exynos5433 should not be affected as eint_base
equals pctl_base in such case.
Fixes: 8b1bd11c1f ("pinctrl: samsung: Add the support the multiple IORESOURCE_MEM for one pin-bank")
Reported-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Tested-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8a5a90a2a4 upstream.
Sergey noticed a small but fatal mistake in __tty_insert_flip_char,
leading to an oops in an interrupt handler when using any serial
port.
The problem is that I accidentally took the tty_buffer pointer
before calling __tty_buffer_request_room(), which replaces the
buffer. This moves the pointer lookup to the right place after
allocating the new buffer space.
Fixes: 979990c628 ("tty: improve tty_insert_flip_char() fast path")
Reported-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Tested-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 065ea0a7af upstream.
While working on improving the fast path of tty_insert_flip_char(),
I noticed that by calling tty_buffer_request_room(), we needlessly
move to the separate flag buffer mode for the tty, even when all
characters use TTY_NORMAL as the flag.
This changes the code to call __tty_buffer_request_room() with the
correct flag, which will then allocate a regular buffer when it rounds
out of space but no special flags have been used. I'm guessing that
this is the behavior that Peter Hurley intended when he introduced
the compacted flip buffers.
Fixes: acc0f67f30 ("tty: Halve flip buffer GFP_ATOMIC memory consumption")
Cc: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 979990c628 upstream.
kernelci.org reports a crazy stack usage for the VT code when CONFIG_KASAN
is enabled:
drivers/tty/vt/keyboard.c: In function 'kbd_keycode':
drivers/tty/vt/keyboard.c:1452:1: error: the frame size of 2240 bytes is larger than 2048 bytes [-Werror=frame-larger-than=]
The problem is that tty_insert_flip_char() gets inlined many times into
kbd_keycode(), and also into other functions, and each copy requires 128
bytes for stack redzone to check for a possible out-of-bounds access on
the 'ch' and 'flags' arguments that are passed into
tty_insert_flip_string_flags as a variable-length string.
This introduces a new __tty_insert_flip_char() function for the slow
path, which receives the two arguments by value. This completely avoids
the problem and the stack usage goes back down to around 100 bytes.
Without KASAN, this is also slightly better, as we don't have to
spill the arguments to the stack but can simply pass 'ch' and 'flag'
in registers, saving a few bytes in .text for each call site.
This should be backported to linux-4.0 or later, which first introduced
the stack sanitizer in the kernel.
Fixes: c420f167db ("kasan: enable stack instrumentation")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 122d6a3473 upstream.
We should only see devices with interrupt endpoints. Ignore any other
endpoints that we find, so we don't send try to send them interrupt URBs
and trigger a WARN down in the USB stack.
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Cameron Gutman <aicommander@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0c96b27305 upstream.
If cpuhp_store_callbacks() is called for CPUHP_AP_ONLINE_DYN or
CPUHP_BP_PREPARE_DYN, which are the indicators for dynamically allocated
states, then cpuhp_store_callbacks() allocates a new dynamic state. The
first allocation in each range returns CPUHP_AP_ONLINE_DYN or
CPUHP_BP_PREPARE_DYN.
If cpuhp_remove_state() is invoked for one of these states, then there is
no protection against the allocation mechanism. So the removal, which
should clear the callbacks and the name, gets a new state assigned and
clears that one.
As a consequence the state which should be cleared stays initialized. A
consecutive CPU hotplug operation dereferences the state callbacks and
accesses either freed or reused memory, resulting in crashes.
Add a protection against this by checking the name argument for NULL. If
it's NULL it's a removal. If not, it's an allocation.
[ tglx: Added a comment and massaged changelog ]
Fixes: 5b7aa87e04 ("cpu/hotplug: Implement setup/removal interface")
Signed-off-by: Ethan Barnes <ethan.barnes@sandisk.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.or>
Cc: "Srivatsa S. Bhat" <srivatsa@mit.edu>
Cc: Sebastian Siewior <bigeasy@linutronix.d>
Cc: Paul McKenney <paulmck@linux.vnet.ibm.com>
Link: http://lkml.kernel.org/r/DM2PR04MB398242FC7776D603D9F99C894A60@DM2PR04MB398.namprd04.prod.outlook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 35732cf9dd upstream.
Tree RCU guarantees that every online CPU has a memory barrier between
any given grace period and any of that CPU's RCU read-side sections that
must be ordered against that grace period. Since RCU doesn't always
know where read-side critical sections are, the actual implementation
guarantees order against prior and subsequent non-idle non-offline code,
whether in an RCU read-side critical section or not. As a result, there
does not need to be a memory barrier at the end of synchronize_rcu()
and friends because the ordering internal to the grace period has
ordered every CPU's post-grace-period execution against each CPU's
pre-grace-period execution, again for all non-idle online CPUs.
In contrast, SRCU can have non-idle online CPUs that are completely
uninvolved in a given SRCU grace period, for example, a CPU that
never runs any SRCU read-side critical sections and took no part in
the grace-period processing. It is in theory possible for a given
synchronize_srcu()'s wakeup to be delivered to a CPU that was completely
uninvolved in the prior SRCU grace period, which could mean that the
code following that synchronize_srcu() would end up being unordered with
respect to both the grace period and any pre-existing SRCU read-side
critical sections.
This commit therefore adds an smp_mb() to the end of __synchronize_srcu(),
which prevents this scenario from occurring.
Reported-by: Lance Roy <ldr709@gmail.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Lance Roy <ldr709@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4c25b7a390 upstream.
When we have a miss in one order of the mkey cache, we try to get
an mkey from a higher order.
We still need to check that the higher order can be used with UMR
before using it. Otherwise, we will get an mkey with 0 entries and
the post send operation that is used to fill it will complete with
the following error:
mlx5_0:dump_cqe:275:(pid 0): dump error cqe
00000000 00000000 00000000 00000000
00000000 00000000 00000000 00000000
00000000 0f007806 25000025 49ce59d2
Fixes: 49780d42df ("IB/mlx5: Expose MR cache for mlx5_ib")
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Reviewed-by: Ilya Lesokhin <ilyal@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5b0ef650bd upstream.
Section 9.7.7.2.5 of the 1.3 IBTA spec clearly says that receive
credits should never apply to RDMA write.
qib and hfi1 were doing that. The following situation will result
in a QP hang:
- A prior SEND or RDMA_WRITE with immmediate consumed the last
credit for a QP using RC receive buffer credits
- The prior op is acked so there are no more acks
- The peer ULP fails to post receive for some reason
- An RDMA write sees that the credits are exhausted and waits
- The peer ULP posts receive buffers
- The ULP posts a send or RDMA write that will be hung
The fix is to avoid the credit test for the RDMA write operation.
Reviewed-by: Kaike Wan <kaike.wan@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ecdb19f4b5 upstream.
Current code has some serious flaws. Disarm the flag
pending an appropriate patch.
Fixes: 53526500f3 ("IB/hfi1: Permanently enable P_Key checking in HFI")
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Alex Estrin <alex.estrin@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f58e76c1c5 upstream.
copy_in_user() copies data from user-space address @from to user-
space address @to. Hence declare both @from and @to as user-space
pointers.
Fixes: commit d597580d37 ("generic ...copy_..._user primitives")
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b5accbb0df upstream.
When new directory 'DIR1' is created in a directory 'DIR0' with SGID bit
set, DIR1 is expected to have SGID bit set (and owning group equal to
the owning group of 'DIR0'). However when 'DIR0' also has some default
ACLs that 'DIR1' inherits, setting these ACLs will result in SGID bit on
'DIR1' to get cleared if user is not member of the owning group.
Fix the problem by creating __orangefs_set_acl() function that does not
call posix_acl_update_mode() and use it when inheriting ACLs. That
prevents SGID bit clearing and the mode has been properly set by
posix_acl_create() anyway.
Fixes: 073931017b
CC: stable@vger.kernel.org
CC: Mike Marshall <hubcap@omnibond.com>
CC: pvfs2-developers@beowulf-underground.org
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Mike Marshall <hubcap@omnibond.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7bf7a193a9 upstream.
Fix up all the compiler warnings that have crept in.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9c72a18e46 upstream.
In raid5, there are scenarios where some ios are deferred to a later
time, and some IO need a flush to complete. To make sure we make
progress with these IOs, we need to call the following functions:
flush_deferred_bios(conf);
r5l_flush_stripe_to_raid(conf->log);
Both of these functions are called in raid5d(), but missing in
raid5_do_work(). As a result, these functions are not called
when multi-threading (group_thread_cnt > 0) is enabled. This patch
adds calls to these function to raid5_do_work().
Note for stable branches:
r5l_flush_stripe_to_raid(conf->log) is need for 4.4+
flush_deferred_bios(conf) is only needed for 4.11+
Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 208410b546 upstream.
Data allocated from mempool doesn't always get initialized, this happens when
the data is reused instead of fresh allocation. In the raid1/10 case, we must
reinitialize the bios.
Reported-by: Jonathan G. Underwood <jonathan.underwood@gmail.com>
Fixes: f0250618361d(md: raid10: don't use bio's vec table to manage resync pages)
Fixes: 98d30c5812c3(md: raid1: don't use bio's vec table to manage resync pages)
Cc: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6c370590cf upstream.
In function xfs_test_remount_options(), kfree() is used to free memory
allocated by kmem_zalloc(). But it is better to use kmem_free().
Signed-off-by: Pan Bian <bianpan2016@163.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8353a814f2 upstream.
Our loop in xfs_finish_page_writeback, which iterates over all buffer
heads in a page and then calls end_buffer_async_write, which also
iterates over all buffers in the page to check if any I/O is in flight
is not only inefficient, but also potentially dangerous as
end_buffer_async_write can cause the page and all buffers to be freed.
Replace it with a single loop that does the work of end_buffer_async_write
on a per-page basis.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dd60687ee5 upstream.
Reject attempts to set XFLAGS that correspond to di_flags2 inode flags
if the inode isn't a v3 inode, because di_flags2 only exists on v3.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 47c7d0b195 upstream.
When calling into _xfs_log_force{,_lsn}() with a pointer
to log_flushed variable, log_flushed will be set to 1 if:
1. xlog_sync() is called to flush the active log buffer
AND/OR
2. xlog_wait() is called to wait on a syncing log buffers
xfs_file_fsync() checks the value of log_flushed after
_xfs_log_force_lsn() call to optimize away an explicit
PREFLUSH request to the data block device after writing
out all the file's pages to disk.
This optimization is incorrect in the following sequence of events:
Task A Task B
-------------------------------------------------------
xfs_file_fsync()
_xfs_log_force_lsn()
xlog_sync()
[submit PREFLUSH]
xfs_file_fsync()
file_write_and_wait_range()
[submit WRITE X]
[endio WRITE X]
_xfs_log_force_lsn()
xlog_wait()
[endio PREFLUSH]
The write X is not guarantied to be on persistent storage
when PREFLUSH request in completed, because write A was submitted
after the PREFLUSH request, but xfs_file_fsync() of task A will
be notified of log_flushed=1 and will skip explicit flush.
If the system crashes after fsync of task A, write X may not be
present on disk after reboot.
This bug was discovered and demonstrated using Josef Bacik's
dm-log-writes target, which can be used to record block io operations
and then replay a subset of these operations onto the target device.
The test goes something like this:
- Use fsx to execute ops of a file and record ops on log device
- Every now and then fsync the file, store md5 of file and mark
the location in the log
- Then replay log onto device for each mark, mount fs and compare
md5 of file to stored value
Cc: Christoph Hellwig <hch@lst.de>
Cc: Josef Bacik <jbacik@fb.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 742d842907 upstream.
Currently flag switching can be used to easily crash the kernel. Disable
the per-inode DAX flag until that is sorted out.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2dd3d709fc upstream.
The owner change bmbt scan that occurs during extent swap operations
does not handle ordered buffer failures. Buffers that cannot be
marked ordered must be physically logged so previously dirty ranges
of the buffer can be relogged in the transaction.
Since the bmbt scan may need to process and potentially log a large
number of blocks, we can't expect to complete this operation in a
single transaction. Update extent swap to use a permanent
transaction with enough log reservation to physically log a buffer.
Update the bmbt scan to physically log any buffers that cannot be
ordered and to terminate the scan with -EAGAIN. On -EAGAIN, the
caller rolls the transaction and restarts the scan. Finally, update
the bmbt scan helper function to skip bmbt blocks that already match
the expected owner so they are not reprocessed after scan restarts.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
[darrick: fix the xfs_trans_roll call]
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a5814bceea upstream.
Ordered buffers are used in situations where the buffer is not
physically logged but must pass through the transaction/logging
pipeline for a particular transaction. As a result, ordered buffers
are not unpinned and written back until the transaction commits to
the log. Ordered buffers have a strict requirement that the target
buffer must not be currently dirty and resident in the log pipeline
at the time it is marked ordered. If a dirty+ordered buffer is
committed, the buffer is reinserted to the AIL but not physically
relogged at the LSN of the associated checkpoint. The buffer log
item is assigned the LSN of the latest checkpoint and the AIL
effectively releases the previously logged buffer content from the
active log before the buffer has been written back. If the tail
pushes forward and a filesystem crash occurs while in this state, an
inconsistent filesystem could result.
It is currently the caller responsibility to ensure an ordered
buffer is not already dirty from a previous modification. This is
unclear and error prone when not used in situations where it is
guaranteed a buffer has not been previously modified (such as new
metadata allocations).
To facilitate general purpose use of ordered buffers, update
xfs_trans_ordered_buf() to conditionally order the buffer based on
state of the log item and return the status of the result. If the
bli is dirty, do not order the buffer and return false. The caller
must either physically log the buffer (having acquired the
appropriate log reservation) or push it from the AIL to clean it
before it can be marked ordered in the current transaction.
Note that ordered buffers are currently only used in two situations:
1.) inode chunk allocation where previously logged buffers are not
possible and 2.) extent swap which will be updated to handle ordered
buffer failures in a separate patch.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6fb10d6d22 upstream.
The extent swap operation currently resets bmbt block owners before
the inode forks are swapped. The bmbt buffers are marked as ordered
so they do not have to be physically logged in the transaction.
This use of ordered buffers is not safe as bmbt buffers may have
been previously physically logged. The bmbt owner change algorithm
needs to be updated to physically log buffers that are already dirty
when/if they are encountered. This means that an extent swap will
eventually require multiple rolling transactions to handle large
btrees. In addition, all inode related changes must be logged before
the bmbt owner change scan begins and can roll the transaction for
the first time to preserve fs consistency via log recovery.
In preparation for such fixes to the bmbt owner change algorithm,
refactor the bmbt scan out of the extent fork swap code to the last
operation before the transaction is committed. Update
xfs_swap_extent_forks() to only set the inode log flags when an
owner change scan is necessary. Update xfs_swap_extents() to trigger
the owner change based on the inode log flags. Note that since the
owner change now occurs after the extent fork swap, the inode btrees
must be fixed up with the inode number of the current inode (similar
to log recovery).
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 99c794c639 upstream.
Extent swap uses xfs_btree_visit_blocks() to fix up bmbt block
owners on v5 (!rmapbt) filesystems. The bmbt scan uses
xfs_btree_lookup_get_block() to read bmbt blocks which verifies the
current owner of the block against the parent inode of the bmbt.
This works during extent swap because the bmbt owners are updated to
the opposite inode number before the inode extent forks are swapped.
The modified bmbt blocks are marked as ordered buffers which allows
everything to commit in a single transaction. If the transaction
commits to the log and the system crashes such that recovery of the
extent swap is required, log recovery restarts the bmbt scan to fix
up any bmbt blocks that may have not been written back before the
crash. The log recovery bmbt scan occurs after the inode forks have
been swapped, however. This causes the bmbt block owner verification
to fail, leads to log recovery failure and requires xfs_repair to
zap the log to recover.
Define a new invalid inode owner flag to inform the btree block
lookup mechanism that the current inode may be invalid with respect
to the current owner of the bmbt block. Set this flag on the cursor
used for change owner scans to allow this operation to work at
runtime and during log recovery.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Fixes: bb3be7e7c ("xfs: check for bogus values in btree block headers")
Cc: stable@vger.kernel.org
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>