[ Upstream commit d5aede3e6d ]
1. Reorder interrupts
2. Fix typo: s/spi_lr_overhead/spi_lr_overread/
3. Rename node: s/spi-nor@0/flash@0/
This fixes:
arch/arm/boot/dts/bcm4709-buffalo-wxr-1900dhp.dt.yaml: spi@18029200: interrupt-names: 'oneOf' conditional failed, one must be fixed:
['spi_lr_fullness_reached', 'spi_lr_session_aborted', 'spi_lr_impatient', 'spi_lr_session_done', 'spi_lr_overhead', 'mspi_done', 'mspi_halted'] is too long
Additional items are not allowed ('spi_lr_session_aborted', 'spi_lr_impatient', 'spi_lr_session_done', 'spi_lr_overhead', 'mspi_done', 'mspi_halted' were unexpected)
'mspi_done' was expected
'spi_l1_intr' was expected
'mspi_halted' was expected
'spi_lr_fullness_reached' was expected
'spi_lr_session_aborted' was expected
'spi_lr_impatient' was expected
'spi_lr_session_done' was expected
'spi_lr_overread' was expected
From schema: Documentation/devicetree/bindings/spi/brcm,spi-bcm-qspi.yaml
arch/arm/boot/dts/bcm4709-buffalo-wxr-1900dhp.dt.yaml: spi-nor@0: $nodename:0: 'spi-nor@0' does not match '^flash(@.*)?$'
From schema: Documentation/devicetree/bindings/mtd/jedec,spi-nor.yaml
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 92e669017f ]
The SCL gpio pin used by I2C bus for recovery needs to be configured as
open drain, so fix the binding example accordingly.
In relation with fix c5a2838025 ("ARM: dts: at91: Configure I2C SCL
gpio as open drain").
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Fixes: 19e5cef058 ("dt-bindings: i2c: at91: document optional bus recovery properties")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0cb7af474e ]
During an async commands execution the Rx buffer length is at first set
to max_msg_sz when the synchronous part of the command is first sent.
However once the synchronous part completes the transport layer waits
for the delayed response which will be processed using the same xfer
descriptor initially allocated. Since synchronous response received at
the end of the xfer will shrink the Rx buffer length to the effective
payload response length, it needs to be reset again.
Raise the Rx buffer length again to max_msg_sz before fetching the
delayed response to ensure full response is read correctly from the
shared memory.
Link: https://lore.kernel.org/r/20210601102421.26581-2-cristian.marussi@arm.com
Fixes: 58ecdf03db ("firmware: arm_scmi: Add support for asynchronous commands and delayed response")
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
[sudeep.holla: moved reset to scmi_handle_response as it could race with
do_xfer_with_response]
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f0fce06e34 ]
In this new power domain driver, when adding one power domain
it will prepare the dependent clocks at the same.
So we only do clk_bulk_enable/disable control during power ON/OFF.
When system suspend, the pm runtime framework will forcely power off
power domains. However, the dependent clocks are disabled but kept
prepared.
In MediaTek clock drivers, PLL would be turned ON when we do
clk_bulk_prepare control.
Clock hierarchy:
PLL -->
DIV_CK -->
CLK_MUX
(may be dependent clocks)
-->
SUBSYS_CG
(may be dependent clocks)
It will lead some unexpected clock states during system suspend.
This patch will fix by doing prepare_enable/disable_unprepare on
dependent clocks at the same time while we are going to power on/off
any power domain.
Fixes: 59b644b01c ("soc: mediatek: Add MediaTek SCPSYS power domains")
Signed-off-by: Weiyi Lu <weiyi.lu@mediatek.com>
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Reviewed-by: chun-jie.chen <chun-jie.chen@mediatek.com>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Link: https://lore.kernel.org/r/20210601035905.2970384-1-hsinyi@chromium.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eed6ff1bb2 ]
Mediatek requires mmsys clocks to be unprepared during suspend,
otherwise system has chances to hang.
syscon_regmap_lookup_by_phandle_optional() will attach and prepare the
first clock in smi node, leading to additional prepare to the clock
which is not balanced with the prepare/unprepare pair in resume/suspend
callbacks.
If a power domain node requests an smi node and the smi node's first
clock is an mmsys clock, it will results in an unstable suspend resume.
Fixes: f414854c88 ("soc: mediatek: pm-domains: Add SMI block as bus protection block")
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Reviewed-by: chun-jie.chen <chun-jie.chen@mediatek.com>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Link: https://lore.kernel.org/r/20210601035905.2970384-2-hsinyi@chromium.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7fea67710e ]
When call irq_get_irq_data() to get the IRQ's irq_data failed, an
appropriate error code -ENOENT should be returned. However, we directly
return 'err', which records the IRQ number instead of the error code.
Fixes: 139251fc22 ("firmware: tegra: add bpmp driver for Tegra210")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c1124180eb ]
As per Dmitry Baryshkov [1]:
a) The 2nd "reg" should be 0x3c because "Offset 0x38 is
USB3_DP_COM_REVISION_ID3 (not used by the current driver though)."
b) The 3rd "reg" "is a serdes region and qmp_v3_dp_serdes_tbl contains
registers 0x148 and 0x154."
I think because the 3rd "reg" is a serdes region we should just use
the same size as the 1st "reg"?
[1] https://lore.kernel.org/r/ee5695bb-a603-0dd5-7a7f-695e919b1af1@linaro.org
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Cc: Stephen Boyd <swboyd@chromium.org>
Cc: Jeykumar Sankaran <jsanka@codeaurora.org>
Cc: Chandan Uddaraju <chandanu@codeaurora.org>
Cc: Vara Reddy <varar@codeaurora.org>
Cc: Tanmay Shah <tanmay@codeaurora.org>
Cc: Rob Clark <robdclark@chromium.org>
Fixes: 58fd7ae621 ("arm64: dts: qcom: sc7180: Update dts for DP phy inside QMP phy")
Reported-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20210315103836.1.I9a97120319d43b42353aeac4d348624d60687df7@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c0dcfe6a78 ]
We should indicate that we're not using the HPD pin on this device, per
the binding document. Otherwise if code in the future wants to enable
HPD in the bridge when this property is absent we'll be enabling HPD
when it isn't supposed to be used. Presumably this board isn't using hpd
on the bridge.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Cc: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Steev Klimaszewski <steev@kali.org>
Fixes: 956e9c85f4 ("arm64: dts: qcom: c630: Define eDP bridge and panel")
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20210324231424.2890039-1-swboyd@chromium.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5f551b5ce5 ]
We should indicate that we're not using the HPD pin on this device, per
the binding document. Otherwise if code in the future wants to enable
HPD in the bridge when this property is absent we'll be wasting power
powering hpd when we don't use it on trogdor boards. We didn't notice
this before because the kernel driver blindly disables hpd, but that
won't be true for much longer.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Cc: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Cc: Douglas Anderson <dianders@chromium.org>
Fixes: 7ec3e67307 ("arm64: dts: qcom: sc7180-trogdor: add initial trogdor and lazor dt")
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20210324025534.1837405-1-swboyd@chromium.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1cebcf9932 ]
The Microchip LAN8710Ai PHY requires XTAL1/CLKIN external clock to be
enabled when the nRST is toggled according to datasheet Microchip
LAN8710A/LAN8710Ai DS00002164B page 35 section 3.8.5.1 Hardware Reset:
"
A Hardware reset is asserted by driving the nRST input pin low. When
driven, nRST should be held low for the minimum time detailed in
Section 5.5.3, "Power-On nRST & Configuration Strap Timing," on page
59 to ensure a proper transceiver reset. During a Hardware reset, an
external clock must be supplied to the XTAL1/CLKIN signal.
"
This is accidentally fulfilled in the current setup, where ETHCK_K is used
to supply both PHY XTAL1/CLKIN and is also fed back through eth_clk_fb to
supply ETHRX clock of the DWMAC. Hence, the DWMAC enables ETHRX clock,
that has ETHCK_K as parent, so ETHCK_K clock are also enabled, and then
the PHY reset toggles.
However, this is not always the case, e.g. in case the PHY XTAL1/CLKIN
clock are supplied by some other clock source than ETHCK_K or in case
ETHRX clock are not supplied by ETHCK_K. In the later case, ETHCK_K would
be kept disabled, while ETHRX clock would be enabled, so the PHY would
not be receiving XTAL1/CLKIN clock and the reset would fail.
Improve the DT by adding the PHY clock phandle into the PHY node, which
then also requires moving the PHY reset GPIO specifier in the same place
and that then also requires correct PHY reset GPIO timing, so add that
too.
A brief note regarding the timing, the datasheet says the reset should
stay asserted for at least 100uS and software should wait at least 200nS
after deassertion. Set both delays to 500uS which should be plenty.
Fixes: 34e0c7847d ("ARM: dts: stm32: Add DH Electronics DHCOM STM32MP1 SoM and PDK2 board")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 659b38203f ]
Correct the voltages in the "Power Optimized" (<= 1.5 GHz) Cortex-A57
operating point table entries for the R-Car M3-W and M3-W+ SoCs from
0.82V to 0.83V, as per the R-Car Gen3 EC Manual Errata for Revision
0.53.
Based on a patch for R-Car M3-W in the BSP by Takeshi Kihara
<takeshi.kihara.df@renesas.com>.
Fixes: da7e311334 ("arm64: dts: renesas: r8a7796: Add OPPs table for cpu devices")
Fixes: f51746ad7d ("arm64: dts: renesas: Add Renesas R8A77961 SoC support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/b9e9db907514790574429b83d070c823b36085ef.1619699909.git.geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 44b615ac9f ]
Tag the highest "Power Optimized" (1.5 GHz) Cortex-A57 operating point
table entries for the RZ/G2M, R-Car M3-W and M3-W+ SoCs with the
"opp-suspend" property. This makes sure the system will enter suspend
in the same performance state as it will be resumed by the firmware
later, avoiding state inconsistencies after resume.
Based on a patch for R-Car M3-W in the BSP by Takeshi Kihara
<takeshi.kihara.df@renesas.com>.
Fixes: 800037e815 ("arm64: dts: renesas: r8a774a1: Add operating points")
Fixes: da7e311334 ("arm64: dts: renesas: r8a7796: Add OPPs table for cpu devices")
Fixes: f51746ad7d ("arm64: dts: renesas: Add Renesas R8A77961 SoC support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/45a061c3b0463aac7d10664f47c4afdd999da50d.1619699721.git.geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0fa1baeedf ]
The corresponding MTD code expects the regions to be of 64-bit elements.
Hence, prefix "/bits/ 64", otherwise the regions will not be parsed
correctly.
Fixes: 6a5d3c6119 ("ARM: dts: qcom: sdx55: Add basic devicetree support for Telit FN980 TLB")
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20210512050141.43338-2-manivannan.sadhasivam@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 619d3c4bf8 ]
The corresponding MTD code expects the regions to be of 64-bit elements.
Hence, prefix "/bits/ 64", otherwise the regions will not be parsed
correctly.
Fixes: 3263d4be57 ("ARM: dts: qcom: sdx55: Add basic devicetree support for Thundercomm T55")
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20210512050141.43338-1-manivannan.sadhasivam@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e60fd5ac1f ]
The rmtfs_mem region is a weird one, downstream allocates it
dynamically, and supports a "qcom,guard-memory" property which when set
will reserve 4k above and below the rmtfs memory.
A common from qcom 4.9 kernel msm_sharedmem driver:
/*
* If guard_memory is set, then the shared memory region
* will be guarded by SZ_4K at the start and at the end.
* This is needed to overcome the XPU limitation on few
* MSM HW, so as to make this memory not contiguous with
* other allocations that may possibly happen from other
* clients in the system.
*/
When the kernel tries to touch memory that is too close the
rmtfs region it may cause an XPU violation. Such is the case on the
OnePlus 6 where random crashes would occur usually after boot.
Reserve 4k above and below the rmtfs_mem to avoid hitting these XPU
Violations.
This doesn't entirely solve the random crashes on the OnePlus 6/6T but
it does seem to prevent the ones which happen shortly after modem
bringup.
Fixes: 288ef8a426 ("arm64: dts: sdm845: add oneplus6/6t devices")
Signed-off-by: Caleb Connolly <caleb@connolly.tech>
Link: https://lore.kernel.org/r/20210502014146.85642-4-caleb@connolly.tech
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6ab8c23096 ]
"make dtbs_check" complains:
arch/arm/boot/dts/r8a7779-marzen.dt.yaml: display@fff80000: clock-names:0: 'du.0' was expected
Change the first clock name to match the DT bindings.
This has no effect on actual operation, as the Display Unit driver in
Linux does not use the first clock name on R-Car H1, but just grabs the
first clock.
Fixes: 665d79aa47 ("ARM: shmobile: marzen: Add DU external pixel clock to DT")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/9d5e1b371121883b3b3e10a3df43802a29c6a9da.1619699965.git.geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 54b909436e ]
The scnprintf() function silently truncates the printf() and returns
the number bytes that it was able to copy (not counting the NUL
terminator). Thus, the highest value it can return here is
"NAME_SIZE - 1" and the overflow check is dead code. Fix this by
using the snprintf() function which returns the number of bytes that
would have been copied if there was enough space and changing the
condition from "> NAME_SIZE" to ">= NAME_SIZE".
Fixes: 92589c986b ("rtc-proc: permit the /proc/driver/rtc device to use other devices")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/YJov/pcGmhLi2pEl@mwanda
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b0ddc5b170 ]
The added Kconfig dependency is slightly incorrect, which can
lead to a link failure when the watchdog is a loadable module:
arm-linux-gnueabi-ld: drivers/rtc/rtc-bd70528.o: in function `bd70528_set_rtc_based_timers':
rtc-bd70528.c:(.text+0x6cc): undefined reference to `bd70528_wdt_set'
arm-linux-gnueabi-ld: drivers/rtc/rtc-bd70528.o: in function `bd70528_set_time':
rtc-bd70528.c:(.text+0xaa0): undefined reference to `bd70528_wdt_lock'
arm-linux-gnueabi-ld: rtc-bd70528.c:(.text+0xab8): undefined reference to `bd70528_wdt_unlock'
arm-linux-gnueabi-ld: drivers/rtc/rtc-bd70528.o: in function `bd70528_alm_enable':
rtc-bd70528.c:(.text+0xfc0): undefined reference to `bd70528_wdt_lock'
arm-linux-gnueabi-ld: rtc-bd70528.c:(.text+0x1030): undefined reference to `bd70528_wdt_unlock'
The problem is that it allows to be built-in if MFD_ROHM_BD71828
is built-in, even when the watchdog is a loadable module.
Rework this so that having the watchdog as a loadable module always
forces the rtc to be a module as well instead of built-in,
regardless of bd71828.
Fixes: c56dc069f2 ("rtc: bd70528: Support RTC on ROHM BD71815")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210422151545.2403356-1-arnd@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b19d3479f2 ]
Commit bbc4d71d63 ("net: phy: realtek: fix rtl8211e rx/tx delay
config") sets the RX/TX delay according to the phy-mode property in the
device tree. For the Orange Pi Plus board this is "rgmii", which is the
wrong setting.
Following the example of a900cac375 ("ARM: dts: sun7i: a20: bananapro:
Fix ethernet phy-mode") the phy-mode is changed to "rgmii-id" which gets
the Ethernet working again on this board.
Fixes: bbc4d71d63 ("net: phy: realtek: fix rtl8211e rx/tx delay config")
Reported-by: "B.R. Oake" <broake@mailfence.com>
Reported-by: Vagrant Cascadian <vagrant@reproducible-builds.org>
Link: https://bugs.debian.org/988574
Signed-off-by: Salvatore Bonaccorso <carnil@debian.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210524122111.416885-1-carnil@debian.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 76e5624f3f ]
When no child nodes are matched, an appropriate error code -ENODEV should
be returned. However, we currently do not explicitly assign this error
code to 'err'. As a result, 0 was incorrectly returned.
Fixes: fee10bd226 ("memory: pl353: Add driver for arm pl353 static memory controller")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Link: https://lore.kernel.org/r/20210515040004.6983-1-thunder.leizhen@huawei.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f0e70d4946 ]
Commit 'fbbe38309d ("arm64: defconfig: Allow mt8173-based boards to boot
from usb")' added the MTK_PMIC_WRAP config built-in. It needs to be
built-in in order to be able to boot from USB or the MMC without needing
a ramdisk, but that symbol was already defined as a module so now we are
getting the following warning:
arch/arm64/configs/defconfig:996:warning: override: reassigning to symbol MTK_PMIC_WRAP
Remove the MTK_PMIC_WRAP=m from the defconfig to remove the error.
Fixes: fbbe38309d ("arm64: defconfig: Allow mt8173-based boards to boot from usb")
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Link: https://lore.kernel.org/r/20210423075201.2616023-1-enric.balletbo@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e207457f90 ]
This patch adds missing MODULE_DEVICE_TABLE definition which generates
correct modalias for automatic loading of this driver when it is built
as an external module.
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: 77750bc089 ("reset: Add Broadcom STB SW_INIT reset controller driver")
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Link: https://lore.kernel.org/r/1620789283-15048-1-git-send-email-zou_wei@huawei.com
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 907c5bbb51 ]
Early exits from for_each_available_child_of_node() should decrement the
node reference counter. Reported by Coccinelle:
drivers/memory/atmel-ebi.c:593:1-33: WARNING:
Function "for_each_available_child_of_node" should have of_node_put() before return around line 604.
Fixes: 6a4ec4cd08 ("memory: add Atmel EBI (External Bus Interface) driver")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20210423101815.119341-2-krzysztof.kozlowski@canonical.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2f9dc6a357 ]
Early exits from for_each_available_child_of_node() should decrement the
node reference counter. Reported by Coccinelle:
drivers/memory/stm32-fmc2-ebi.c:1046:1-33: WARNING:
Function "for_each_available_child_of_node" should have of_node_put() before return around line 1051.
Fixes: 66b8173a19 ("memory: stm32-fmc2-ebi: add STM32 FMC2 EBI controller driver")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Christophe Kerello <christophe.kerello@foss.st.com>
Link: https://lore.kernel.org/r/20210423101815.119341-1-krzysztof.kozlowski@canonical.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fd2f171796 ]
There is no "max_brightness" property as pointed out by dtschema:
arch/arm/boot/dts/exynos5422-odroidxu4.dt.yaml: led-controller: led-1: 'max-brightness' is a required property
Fixes: 6658356014 ("ARM: dts: Add support Odroid XU4 board for exynos5422-odroidxu4")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20210505135941.59898-5-krzysztof.kozlowski@canonical.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a7e59c84cf ]
There is no "max_brightness" property as pointed out by dtschema:
arch/arm/boot/dts/exynos5422-odroidhc1.dt.yaml: led-controller: led-1: 'max-brightness' is a required property
Fixes: 1ac49427b5 ("ARM: dts: exynos: Add support for Hardkernel's Odroid HC1 board")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20210505135941.59898-4-krzysztof.kozlowski@canonical.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 75121e1dc9 ]
There is no "max_brightness" property. This brings the intentional
brightness reduce of green LED and dtschema checks as well:
arch/arm/boot/dts/exynos5410-odroidxu.dt.yaml: led-controller-1: led-1: 'max-brightness' is a required property
Fixes: 719f39fec5 ("ARM: dts: exynos5422-odroidxu3: Hook up PWM and use it for LEDs")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20210505135941.59898-3-krzysztof.kozlowski@canonical.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 48d551bf20 ]
Early exits from for_each_compatible_node() should decrement the
node reference counter. Reported by Coccinelle:
arch/arm/mach-exynos/exynos.c:52:1-25: WARNING:
Function "for_each_compatible_node" should have of_node_put() before break around line 58.
Fixes: b3205dea8f ("ARM: EXYNOS: Map SYSRAM through generic DT bindings")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20210425174945.164612-1-krzysztof.kozlowski@canonical.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 466ba3c8ff ]
The driver defined of_device_id table but did not use it with
of_match_table. This prevents usual matching via devicetree and causes
a W=1 warning:
drivers/reset/reset-a10sr.c:111:34: warning:
‘a10sr_reset_of_match’ defined but not used [-Wunused-const-variable=]
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 6270068202 ("reset: Add Altera Arria10 SR Reset Controller")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20210507112803.20012-1-krzysztof.kozlowski@canonical.com
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6ab9d6219f ]
The Intel Gateway reset controller is only present on Intel Gateway
platforms. Hence add a dependency on X86, to prevent asking the user
about this driver when configuring a kernel without Intel Gateway
support.
Fixes: c9aef213e3 ("reset: intel: Add system reset controller driver")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 42f6a76fbe ]
The Broadcom STB RESCAL reset controller is only present on Broadcom
BCM7216 platforms. Hence add a dependency on ARCH_BRCMSTB, to prevent
asking the user about this driver when configuring a kernel without
BCM7216 support.
Also, merely enabling CONFIG_COMPILE_TEST should not enable additional
code, and thus should not enable this driver by default.
Fixes: 4cf176e523 ("reset: Add Broadcom STB RESCAL reset controller")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e6526f9069 ]
Turns out the fephy pins are already claimed in the phy node, which is
rightfully where they should be claimed.
Drop the pinctrl properties from the gmac2phy node for the ROCK Pi E.
Fixes: b918e81f21 ("arm64: dts: rockchip: rk3328: Add Radxa ROCK Pi E")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20210426095916.14574-1-wens@kernel.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6a11ffc2cc ]
However "sys" is not a valid function, and it is always on.
Let's keep existing functions.
Fixes: db792e9adb ("rockchip: rk3399: Add support for FriendlyARM NanoPi R4S")
Suggested-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tianling Shen <cnsztl@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Link: https://lore.kernel.org/r/20210426114652.29542-1-cnsztl@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3d3bb3d27c ]
Two ethernet node was added by
commit 95220046a6 ("ARM: dts: Add ethernet to a bunch of platforms")
and commit d6d0cef55e ("ARM: dts: Add the FOTG210 USB host to Gemini boards")
This patch removes the duplicate one.
Fixes: d6d0cef55e ("ARM: dts: Add the FOTG210 USB host to Gemini boards")
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 681ba73c72 ]
ld.lld warns that the '.modinfo' section is not currently handled:
ld.lld: warning: kernel/built-in.a(workqueue.o):(.modinfo) is being placed in '.modinfo'
ld.lld: warning: kernel/built-in.a(printk/printk.o):(.modinfo) is being placed in '.modinfo'
ld.lld: warning: kernel/built-in.a(irq/spurious.o):(.modinfo) is being placed in '.modinfo'
ld.lld: warning: kernel/built-in.a(rcu/update.o):(.modinfo) is being placed in '.modinfo'
The '.modinfo' section was added in commit 898490c010 ("moduleparam:
Save information about built-in modules in separate file") to the DISCARDS
macro but Hexagon has never used that macro. The unification of DISCARDS
happened in commit 023bf6f1b8 ("linker script: unify usage of discard
definition") in 2009, prior to Hexagon being added in 2011.
Switch Hexagon over to the DISCARDS macro so that anything that is
expected to be discarded gets discarded.
Link: https://lkml.kernel.org/r/20210521011239.1332345-3-nathan@kernel.org
Fixes: e95bf452a9 ("Hexagon: Add configuration and makefiles for the Hexagon architecture.")
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Acked-by: Brian Cain <bcain@codeaurora.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Oliver Glitta <glittao@gmail.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6fef087d0d ]
Patch series "hexagon: Fix build error with CONFIG_STACKDEPOT and select CONFIG_ARCH_WANT_LD_ORPHAN_WARN".
This series fixes an error with ARCH=hexagon that was pointed out by the
patch "mm/slub: use stackdepot to save stack trace in objects".
The first patch fixes that error by handling the '.irqentry.text' and
'.softirqentry.text' sections.
The second patch switches Hexagon over to the common DISCARDS macro, which
should have been done when Hexagon was merged into the tree to match
commit 023bf6f1b8 ("linker script: unify usage of discard definition").
The third patch selects CONFIG_ARCH_WANT_LD_ORPHAN_WARN so that something
like this does not happen again.
This patch (of 3):
Patch "mm/slub: use stackdepot to save stack trace in objects" in -mm
selects CONFIG_STACKDEPOT when CONFIG_STACKTRACE_SUPPORT is selected and
CONFIG_STACKDEPOT requires IRQENTRY_TEXT and SOFTIRQENTRY_TEXT to be
handled after commit 505a0ef15f ("kasan: stackdepot: move
filter_irq_stacks() to stackdepot.c") due to the use of the
__{,soft}irqentry_text_{start,end} section symbols. If those sections are
not handled, the build is broken.
$ make ARCH=hexagon CROSS_COMPILE=hexagon-linux- LLVM=1 LLVM_IAS=1 defconfig all
...
ld.lld: error: undefined symbol: __irqentry_text_start
>>> referenced by stackdepot.c
>>> stackdepot.o:(filter_irq_stacks) in archive lib/built-in.a
>>> referenced by stackdepot.c
>>> stackdepot.o:(filter_irq_stacks) in archive lib/built-in.a
ld.lld: error: undefined symbol: __irqentry_text_end
>>> referenced by stackdepot.c
>>> stackdepot.o:(filter_irq_stacks) in archive lib/built-in.a
>>> referenced by stackdepot.c
>>> stackdepot.o:(filter_irq_stacks) in archive lib/built-in.a
ld.lld: error: undefined symbol: __softirqentry_text_start
>>> referenced by stackdepot.c
>>> stackdepot.o:(filter_irq_stacks) in archive lib/built-in.a
>>> referenced by stackdepot.c
>>> stackdepot.o:(filter_irq_stacks) in archive lib/built-in.a
ld.lld: error: undefined symbol: __softirqentry_text_end
>>> referenced by stackdepot.c
>>> stackdepot.o:(filter_irq_stacks) in archive lib/built-in.a
>>> referenced by stackdepot.c
>>> stackdepot.o:(filter_irq_stacks) in archive lib/built-in.a
...
Add these sections to the Hexagon linker script so the build continues to
work. ld.lld's orphan section warning would have caught this prior to the
-mm commit mentioned above:
ld.lld: warning: kernel/built-in.a(softirq.o):(.softirqentry.text) is being placed in '.softirqentry.text'
ld.lld: warning: kernel/built-in.a(softirq.o):(.softirqentry.text) is being placed in '.softirqentry.text'
ld.lld: warning: kernel/built-in.a(softirq.o):(.softirqentry.text) is being placed in '.softirqentry.text'
Link: https://lkml.kernel.org/r/20210521011239.1332345-1-nathan@kernel.org
Link: https://lkml.kernel.org/r/20210521011239.1332345-2-nathan@kernel.org
Link: https://github.com/ClangBuiltLinux/linux/issues/1381
Fixes: 505a0ef15f ("kasan: stackdepot: move filter_irq_stacks() to stackdepot.c")
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Acked-by: Brian Cain <bcain@codeaurora.org>
Cc: Oliver Glitta <glittao@gmail.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f46f84931a ]
After we grab the lock in nfs4_pnfs_ds_connect(), there is no check for
whether or not ds->ds_clp has already been initialised, so we can end up
adding the same transports multiple times.
Fixes: fc821d5920 ("pnfs/NFSv4.1: Add multipath capabilities to pNFS flexfiles servers over NFSv3")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0b77f97a7e ]
If the layout gets invalidated, we should wait for any outstanding
layoutget requests for that layout to complete, and we should resend
them only after re-establishing the layout stateid.
Fixes: d29b468da4 ("pNFS/NFSv4: Improve rejection of out-of-order layouts")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aa95edf309 ]
If we have multiple outstanding layoutget requests, the current code to
update the layout barrier assumes that the outstanding layout stateids
are updated in order. That's not necessarily the case.
Instead of using the value of lo->plh_outstanding as a guesstimate for
the window of values we need to accept, just wait to update the window
until we're processing the last one. The intention here is just to
ensure that we don't process 2^31 seqid updates without also updating
the barrier.
Fixes: 1bcf34fdac ("pNFS/NFSv4: Update the layout barrier when we schedule a layoutreturn")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ba512c1bc3 ]
Earlier commits refactored some NFS read code and removed
nfs_readpage_async(), but neglected to properly fixup
nfs_readpage_from_fscache_complete(). The code path is
only hit when something unusual occurs with the cachefiles
backing filesystem, such as an IO error or while a cookie
is being invalidated.
Mark page with PG_checked if fscache IO completes in error,
unlock the page, and let the VM decide to re-issue based on
PG_uptodate. When the VM reissues the readpage, PG_checked
allows us to skip over fscache and read from the server.
Link: https://marc.info/?l=linux-nfs&m=162498209518739
Fixes: 1e83b173b2 ("NFS: Add nfs_pageio_complete_read() and remove nfs_readpage_async()")
Signed-off-by: Dave Wysochanski <dwysocha@redhat.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e0340f16a0 upstream.
A previous refactoring of nfs_readpage() might end up calling
wait_on_page_locked_killable() even if readpage_async_filler() failed
with an internal error and pg_error was non-zero (for example, if
nfs_create_request() failed). In the case of an internal error,
skip over wait_on_page_locked_killable() as this is only needed
when the read is sent and an error occurs during completion handling.
Signed-off-by: Dave Wysochanski <dwysocha@redhat.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 500817bf5e ]
We are reading a Big Block Mode value while in Sub Block Mode
when initializing. Fortunately, vm->bbm.bb_size maps to some counter
in the vm->sbm.mb_count array, which is 0 at that point in time.
No harm done; still, this was unintended and is not future-proof.
Fixes: 4ba50cd335 ("virtio-mem: Big Block Mode (BBM) memory hotplug")
Signed-off-by: David Hildenbrand <david@redhat.com>
Link: https://lore.kernel.org/r/20210602185720.31821-2-david@redhat.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e3aadf2e16 ]
After device reset, the virtqueues are not ready so clear the ready
field.
Failing to do so can result in virtio_vdpa failing to load if the device
was previously used by vhost_vdpa and the old values are ready.
virtio_vdpa expects to find VQs in "not ready" state.
Fixes: 1a86b377aa ("vdpa/mlx5: Add VDPA driver for supported mlx5 devices")
Signed-off-by: Eli Cohen <elic@nvidia.com>
Link: https://lore.kernel.org/r/20210606053128.170399-1-elic@nvidia.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 31028cbed2 ]
When 'SB_HW_16' check fails, the error code -ENODEV instead of 0 should be
returned, which is the same as that returned when 'WSS_HW_CMI8330' check
fails.
Fixes: 43bcd973d6 ("[ALSA] Add snd_card_set_generic_dev() call to ISA drivers")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Link: https://lore.kernel.org/r/20210707074051.2663-1-thunder.leizhen@huawei.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ab1016d39c ]
In error cases the dentry may be NULL.
Before 20798dfe24, the encoder also checked dentry and
d_really_is_positive(dentry), but that looks like overkill to me--zero
status should be enough to guarantee a positive dentry.
This isn't the first time we've seen an error-case NULL dereference
hidden in the initialization of a local variable in an xdr encoder. But
I went back through the other recent rewrites and didn't spot any
similar bugs.
Reported-by: JianHong Yin <jiyin@redhat.com>
Reviewed-by: Chuck Lever III <chuck.lever@oracle.com>
Fixes: 20798dfe24 ("NFSD: Update the NFSv3 GETACL result encoder...")
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7b08cf62b1 ]
The double copy of the string is a mistake, plus __assign_str()
uses strlen(), which is wrong to do on a string that isn't
guaranteed to be NUL-terminated.
Fixes: 6019ce0742 ("NFSD: Add a tracepoint to record directory entry encoding")
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
