The main loop in calculate_order() currently tries to find an order with
at most 1/4 waste. If that's impossible (for particular large object
sizes), there's a fallback that will try to place one object within
slab_max_order.
If we expand the loop boundary to also allow up to 1/2 waste as the last
resort, we can remove the fallback and simplify the code, as the loop
will find an order for such sizes as well. Note we don't need to allow
more than 1/2 waste as that will never happen - calc_slab_order() would
calculate more objects to fit, reducing waste below 1/2.
Successfully finding an order in the loop (compared to the fallback)
will also have the benefit in trying to satisfy min_objects, because the
fallback was passing 1. Thus the resulting slab orders might be larger
(not because it would improve waste, but to reduce pressure on shared
locks), which is one of the goals of calculate_order().
For example, with nr_cpus=1 and 4kB PAGE_SIZE, slub_max_order=3, before
the patch we would get the following orders for these object sizes:
2056 to 10920 - order-3 as selected by the loop
10928 to 12280 - order-2 due to fallback, as <1/4 waste is not possible
12288 to 32768 - order-3 as <1/4 waste is again possible
After the patch:
2056 to 32768 - order-3, because even in the range of 10928 to 12280 we
try to satisfy the calculated min_objects.
As a result the code is simpler and gives more consistent results.
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Reviewed-by: Feng Tang <feng.tang@intel.com>
Reviewed-and-tested-by: Jay Patel <jaypatel@linux.ibm.com>
calculate_order() currently has two nested loops. The inner one that
gradually modifies the acceptable waste from 1/16 up to 1/4, and the
outer one that decreases min_objects down to 2.
Upon closer inspection, the outer loop is unnecessary. Decreasing
min_objects could have in theory two effects to make the inner loop and
its call to calc_slab_order() succeed where a previous iteration with
higher min_objects would not:
- it could cause the min_objects-derived min_order to fit within
slub_max_order. But min_objects is already pre-capped to max_objects
that's derived from slub_max_order above the loops, so every iteration
tries at least slub_max_order in calc_slab_order()
- it could cause calc_slab_order() to be called with lower min_objects
thus potentially lower min_order in its loop. This would make a
difference if the lower order could cause the fractional waste test to
succeed where a higher order has already failed with same fract_leftover
in the previous iteration with a higher min_order. But that's not
possible, because increasing the order can only result in lower (or
same) fractional waste. If we increase the slab size 2 times, we will
fit at least 2 times the number of objects (thus same fraction of
waste), or it will allow us to fit one more object (lower fraction of
waste).
For more confidence I have tried adding a printk to notify when
decreasing min_objects resulted in a success, and simulated calculations
for a range of object sizes, nr_cpus and page_sizes. As expected, the
printk never triggered.
Thus remove the outer loop and adjust comments accordingly.
There's almost no functional change except a weird corner case when
slub_min_objects=1 on boot command line would cause the whole two nested
loops to be skipped before this patch. Now it would try to find the best
layout as usual, resulting in potentially higher orderthat minimizes
waste. This is not wrong and will be further expanded by the next patch.
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Reviewed-by: Feng Tang <feng.tang@intel.com>
Reviewed-and-tested-by: Jay Patel <jaypatel@linux.ibm.com>
If calculate_order() can't fit even a single large object within
slub_max_order, it will try using the smallest necessary order that may
exceed slub_max_order but not MAX_ORDER.
Currently this is done with a call to calc_slab_order() which is
unnecessary. We can simply use get_order(size). No functional change.
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Reviewed-by: Feng Tang <feng.tang@intel.com>
Reviewed-and-tested-by: Jay Patel <jaypatel@linux.ibm.com>
Currently there are 2 parameters could be setup from kernel cmdline:
slub_min_order and slub_max_order. It's possible that the user
configured slub_min_order is bigger than the default slub_max_order
[1], which can still take effect, as calculate_oder() will use MAX_ORDER
as a fallback to check against, but has some downsides:
* the kernel message about SLUB will be strange in showing min/max
orders:
SLUB: HWalign=64, Order=9-3, MinObjects=0, CPUs=16, Nodes=1
* in calculate_order() called by each slab, the 2 loops of
calc_slab_order() will all be meaningless due to slub_min_order
is bigger than slub_max_order
* prevent future code cleanup like in [2].
Fix it by adding some sanity check to enforce the min/max semantics.
[1]. https://lore.kernel.org/lkml/21a0ba8b-bf05-0799-7c78-2a35f8c8d52a@os.amperecomputing.com/
[2]. https://lore.kernel.org/lkml/20230908145302.30320-7-vbabka@suse.cz/
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
We use size_t, ssize_t, bool and some other types defined in
linux/types.h so include it in the driver.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Create a section that specifies how to deal with DRM device resets for
kernel and userspace drivers.
Signed-off-by: André Almeida <andrealmeid@igalia.com>
Acked-by: Pekka Paalanen <pekka.paalanen@collabora.com>
Acked-by: Sebastian Wick <sebastian.wick@redhat.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230929092509.42042-1-andrealmeid@igalia.com
Compared with normal doorbell, using record doorbell can shorten the
process of ringing the doorbell and reduce the latency.
Add a flag HNS_ROCE_CAP_FLAG_SRQ_RECORD_DB to allow FW to
enable/disable SRQ record doorbell.
If the flag above is set, allocate the dma buffer for SRQ record
doorbell and write the buffer address into SRQC during SRQ creation.
For userspace SRQ, add a flag HNS_ROCE_RSP_SRQ_CAP_RECORD_DB to notify
userspace whether the SRQ record doorbell is enabled.
Signed-off-by: Yangyang Li <liyangyang20@huawei.com>
Signed-off-by: Junxian Huang <huangjunxian6@hisilicon.com>
Link: https://lore.kernel.org/r/20230926130026.583088-1-huangjunxian6@hisilicon.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
When the master device is unbinded, make sure to clean up all of the
steering rules or flow tables that were created over the master, in
order to allow proper unbinding of master, and for ethernet traffic
to continue to work independently.
Upon bringing master device back up and attaching the slave to it,
checks if the slave already has IPsec configured and if so reconfigure
the rules needed to support RoCE traffic.
Note that while master device is unbound, the user is unable to
configure IPsec again, since they are in a kind of illegal state in
which they are in MPV mode but the slave has no master.
However if IPsec was configured before hand, it will continue to work
for ethernet traffic while master is unbound, and would continue to
work for all traffic when the master is bound back again.
Signed-off-by: Patrisious Haddad <phaddad@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Link: https://lore.kernel.org/r/8434e88912c588affe51b34669900382a132e873.1695296682.git.leon@kernel.org
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Add empty flow table in RDMA_RX master domain, to forward all received
traffic to it, in order to continue through the FW RoCE steering.
In order to achieve that however, first we check if the decrypted
traffic is RoCEv2, if so then forward it to RDMA_RX domain.
But in case the traffic is coming from the slave, have to first send the
traffic to an alias table in order to switch gvmi and from there we can
go to the appropriate gvmi flow table in RDMA_RX master domain.
Signed-off-by: Patrisious Haddad <phaddad@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Link: https://lore.kernel.org/r/d2200b53158b1e7ef30996812107dd7207485c28.1695296682.git.leon@kernel.org
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Add steering tables/rules in RDMA_TX master domain, to forward all traffic
to IPsec crypto table in NIC domain.
But in case the traffic is coming from the slave, have to first send the
traffic to an alias table in order to switch gvmi and from there we can
go to the appropriate gvmi crypto table in NIC domain.
Signed-off-by: Patrisious Haddad <phaddad@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Link: https://lore.kernel.org/r/7ca5cf1ac5c6979359b8726e97510574e2b3d44d.1695296682.git.leon@kernel.org
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Implements functions which creates an alias flow table, and check
if alias flow table creation is even supported, and if successful
returns the created alias flow table object id.
This function would be used in later patches to allow jumping from
one vhca to another, in order to add support for MPV mode.
Signed-off-by: Patrisious Haddad <phaddad@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Link: https://lore.kernel.org/r/36e15ef41586f2a9aacc65b935de18391eef5607.1695296682.git.leon@kernel.org
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Add functions which allow one vhca to access another vhca object,
and functions that creates an alias object or destroys it.
Together they can be used to create cross vhca flow table that is able
jump from the steering domain that is managed by one vport,
to the steering domain on a different vport.
Signed-off-by: Patrisious Haddad <phaddad@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Link: https://lore.kernel.org/r/f45a9c85319fa783186b8988abcd64955b5f2a0c.1695296682.git.leon@kernel.org
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Add all the capabilities needed to check for alias object support.
As well as all the fields or commands needed for its creation and
the creation of flow table that is able to jump to an alias object.
Signed-off-by: Patrisious Haddad <phaddad@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Link: https://lore.kernel.org/r/544c030f2a78c4adf3fe6b64f97a39cc1bbdabb9.1695296682.git.leon@kernel.org
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Store the mlx5e priv devcom component within IPsec RoCE to enable
the IPsec RoCE code to access the other device's private information.
This includes retrieving the necessary device information and
the IPsec database, which helps determine if IPsec is configured or not.
Signed-off-by: Patrisious Haddad <phaddad@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Link: https://lore.kernel.org/r/5bb3160ceeb07523542302886da54c78eef0d2af.1695296682.git.leon@kernel.org
Signed-off-by: Leon Romanovsky <leon@kernel.org>
If the device is in MPV mode, the ethernet driver would now register
to events from IB driver about core devices affiliation or
de-affiliation.
Use the key provided in said event to connect each mlx5e priv
instance to it's master counterpart, this way the ethernet driver
is now aware of who is his master core device and even more, such
as knowing if partner device has IPsec configured or not.
Signed-off-by: Patrisious Haddad <phaddad@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Link: https://lore.kernel.org/r/279adfa0aa3a1957a339086f2c1739a50b8e4b68.1695296682.git.leon@kernel.org
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Send blocking events from IB driver whenever the device is done being
affiliated or if it is removed from an affiliation.
This is useful since now the EN driver can register to those event and
know when a device is affiliated or not.
Signed-off-by: Patrisious Haddad <phaddad@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Link: https://lore.kernel.org/r/a7491c3e483cfd8d962f5f75b9a25f253043384a.1695296682.git.leon@kernel.org
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Since commit 9bf19fbf0c ("media: v4l: async: Rework internal lists"), aka
v6.6-rc1~97^2~198, probing the tegra-video VI driver causes infinite
recursion due tegra_vi_graph_parse_one() calling itself until:
[ 1.571168] Insufficient stack space to handle exception!
...
[ 1.591416] Internal error: kernel stack overflow: 0 [#1] PREEMPT SMP ARM
...
[ 3.861013] of_phandle_iterator_init from __of_parse_phandle_with_args+0x40/0xf0
[ 3.868497] __of_parse_phandle_with_args from of_fwnode_graph_get_remote_endpoint+0x68/0xa8
[ 3.876938] of_fwnode_graph_get_remote_endpoint from fwnode_graph_get_remote_port_parent+0x30/0x7c
[ 3.885984] fwnode_graph_get_remote_port_parent from tegra_vi_graph_parse_one+0x7c/0x224
[ 3.894158] tegra_vi_graph_parse_one from tegra_vi_graph_parse_one+0x144/0x224
[ 3.901459] tegra_vi_graph_parse_one from tegra_vi_graph_parse_one+0x144/0x224
[ 3.908760] tegra_vi_graph_parse_one from tegra_vi_graph_parse_one+0x144/0x224
[ 3.916061] tegra_vi_graph_parse_one from tegra_vi_graph_parse_one+0x144/0x224
...
[ 4.857892] tegra_vi_graph_parse_one from tegra_vi_graph_parse_one+0x144/0x224
[ 4.865193] tegra_vi_graph_parse_one from tegra_vi_graph_parse_one+0x144/0x224
[ 4.872494] tegra_vi_graph_parse_one from tegra_vi_init+0x574/0x6d4
[ 4.878842] tegra_vi_init from host1x_device_init+0x84/0x15c
[ 4.884594] host1x_device_init from host1x_video_probe+0xa0/0x114
[ 4.890770] host1x_video_probe from really_probe+0xe0/0x400
The reason is the mentioned commit changed tegra_vi_graph_find_entity() to
search for an entity in the done notifier list:
> @@ -1464,7 +1464,7 @@ tegra_vi_graph_find_entity(struct tegra_vi_channel *chan,
> struct tegra_vi_graph_entity *entity;
> struct v4l2_async_connection *asd;
>
> - list_for_each_entry(asd, &chan->notifier.asc_list, asc_entry) {
> + list_for_each_entry(asd, &chan->notifier.done_list, asc_entry) {
> entity = to_tegra_vi_graph_entity(asd);
> if (entity->asd.match.fwnode == fwnode)
> return entity;
This is not always correct, being tegra_vi_graph_find_entity() called in
three locations, in this order:
1. tegra_vi_graph_parse_one() -- called while probing
2. tegra_vi_graph_notify_bound() -- the .bound notifier op
3. tegra_vi_graph_build() -- called in the .complete notifier op
Locations 1 and 2 are called before moving the entity from waiting_list to
done_list, thus they won't find what they are looking for in
done_list. Location 3 happens afterwards and thus it is not broken, however
it means tegra_vi_graph_find_entity() should not search in the same list
every time.
The error appears at step 1: tegra_vi_graph_parse_one() iterates
recursively until it finds the entity already notified, which now never
happens.
Fix by passing the specific notifier list pointer to
tegra_vi_graph_find_entity() instead of the channel, so each caller can
search in whatever list is correct.
Also improve the tegra_vi_graph_find_entity() comment.
Fixes: 9bf19fbf0c ("media: v4l: async: Rework internal lists")
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
[Sakari Ailus: Wrapped some long lines.]
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Some missing select statements were already added back, but I ran into
another one that is missing:
ERROR: modpost: "v4l2_fwnode_endpoint_free" [drivers/media/pci/intel/ivsc/ivsc-csi.ko] undefined!
ERROR: modpost: "v4l2_fwnode_endpoint_alloc_parse" [drivers/media/pci/intel/ivsc/ivsc-csi.ko] undefined!
ERROR: modpost: "v4l2_fwnode_endpoint_parse" [drivers/media/pci/intel/ivsc/ivsc-csi.ko] undefined!
Fixes: 29006e196a ("media: pci: intel: ivsc: Add CSI submodule")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[Sakari Ailus: Drop V4L2_ASYNC dependency, it is implied now.]
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The current Kconfig symbol dependencies allow having the following Kconfig
symbol values
CONFIG_IPU_BRIDGE=m
CONFIG_VIDEO_IPU3_CIO2=y
CONFIG_CIO2_BRIDGE=n
This does not work as the IPU bridge API is conditional to
IS_ENABLED(CONFIG_IPU_BRIDGE). Fix this by changing the dependencies so
that CONFIG_IPU_BRIDGE can be separately selected.
The CONFIG_CIO2_BRIDGE symbol becomes redundant as a result and is
removed.
Fixes: 2545a2c02b ("media: ipu3-cio2: allow ipu_bridge to be a module again")
Suggested-by: Arnd Bergmann <arnd@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The commit in Fixes has reordered the code and the error handling path.
However one 'goto' was missed.
Fix it and branch at the correct place in the error handling path.
Fixes: 5073d10cba ("media: pxa_camera: Register V4L2 device early")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The "trigger-sources" phandle used for LED triggers are special:
the DT bindings mandate that such triggers have the same phandle
references no matter what the trigger is. A GPIO is just another
kind of device that can trigger a LED.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Similarly to PXA3xx and MMP2, pinctrl-single isn't capable of setting
pin direction on MMP either.
Fixes: a770d94637 ("gpio: pxa: add pin control gpio direction and request")
Signed-off-by: Duje Mihanović <duje.mihanovic@skole.hr>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Add support for the 2700x1224 AMOLED BOE panel bundled with a RM692E5
driver IC, as found on the Fairphone 5 smartphone.
Co-developed-by: Luca Weiss <luca.weiss@fairphone.com>
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230927-topic-fp5_disp-v2-2-7b5e1d1662a6@linaro.org
The maple tree register cache is based on a much more modern data structure
than the rbtree cache and makes optimisation choices which are probably
more appropriate for modern systems than those made by the rbtree cache.
Signed-off-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20231001-drm-sn65dsi83-maple-v1-2-5519799a55e5@kernel.org
The ili9322 driver has a volatile_reg() operation in it's regmap which
always returns false. This is redundant since it is the default in the
regmap core, remove the operation for a trivial code size and performance
improvement.
Signed-off-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20231001-drm-sn65dsi83-maple-v1-1-5519799a55e5@kernel.org
The maple tree register cache is based on a much more modern data structure
than the rbtree cache and makes optimisation choices which are probably
more appropriate for modern systems than those made by the rbtree cache.
Signed-off-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20231001-drm-sn65dsi83-maple-v1-1-cf8ad22b6be0@kernel.org
The maple tree register cache is based on a much more modern data structure
than the rbtree cache and makes optimisation choices which are probably
more appropriate for modern systems than those made by the rbtree cache.
Signed-off-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20231001-drm-lt9211-maple-v1-1-1cf74fb10991@kernel.org
The maple tree register cache is based on a much more modern data structure
than the rbtree cache and makes optimisation choices which are probably
more appropriate for modern systems than those made by the rbtree cache.
Signed-off-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20231001-drm-chipone-maple-v1-1-fb3ce5a53710@kernel.org
The maple tree register cache is based on a much more modern data structure
than the rbtree cache and makes optimisation choices which are probably
more appropriate for modern systems than those made by the rbtree cache.
Signed-off-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20231001-drm-tc358767-maple-v1-1-f759fcc4bd98@kernel.org
The maple tree register cache is based on a much more modern data structure
than the rbtree cache and makes optimisation choices which are probably
more appropriate for modern systems than those made by the rbtree cache.
Signed-off-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20231001-drm-dlpc3433-maple-v1-1-7d71170c010b@kernel.org
The maple tree register cache is based on a much more modern data structure
than the rbtree cache and makes optimisation choices which are probably
more appropriate for modern systems than those made by the rbtree cache.
Signed-off-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230929-drm-adv7511-v1-1-b871b28ee594@kernel.org
Petr Machata says:
====================
mlxsw: Provide enhancements and new feature
Vadim Pasternak writes:
Patch #1 - Optimize transaction size for efficient retrieval of module
data.
Patch #3 - Enable thermal zone binding with new cooling device.
Patch #4 - Employ standard macros for dividing buffer into the chunks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Use standard macro DIV_ROUND_UP() to determine the number of chunks
required for a given buffer.
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend the list of allowed external cooling devices for thermal zone
binding to include devices of type "emc2305".
The motivation is to provide support for the system SN2201, which is
equipped with the Spectrum-1 ASIC.
The system's airflow control is managed by the EMC2305 RPM-based PWM
Fan Speed Controller as the cooling device.
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MTBR register is used to read temperatures from multiple sensors in
one transaction, but the driver only reads from a single sensor in each
transaction.
Rrestrict the payload size of the MTBR register to prevent the
transmission of redundant data to the firmware.
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the pathological case of building sky2 with 16k PAGE_SIZE, the
frag_addr[] array would never be used, so the original code was correct
that size should be 0. But the compiler now gets upset with 0 size arrays
in places where it hasn't eliminated the code that might access such an
array (it can't figure out that in this case an rx skb with fragments
would never be created). To keep the compiler happy, make sure there is
at least 1 frag_addr in struct rx_ring_info:
In file included from include/linux/skbuff.h:28,
from include/net/net_namespace.h:43,
from include/linux/netdevice.h:38,
from drivers/net/ethernet/marvell/sky2.c:18:
drivers/net/ethernet/marvell/sky2.c: In function 'sky2_rx_unmap_skb':
include/linux/dma-mapping.h:416:36: warning: array subscript i is outside array bounds of 'dma_addr_t[0]' {aka 'long long unsigned int[]'} [-Warray-bounds=]
416 | #define dma_unmap_page(d, a, s, r) dma_unmap_page_attrs(d, a, s, r, 0)
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/marvell/sky2.c:1257:17: note: in expansion of macro 'dma_unmap_page'
1257 | dma_unmap_page(&pdev->dev, re->frag_addr[i],
| ^~~~~~~~~~~~~~
In file included from drivers/net/ethernet/marvell/sky2.c:41:
drivers/net/ethernet/marvell/sky2.h:2198:25: note: while referencing 'frag_addr'
2198 | dma_addr_t frag_addr[ETH_JUMBO_MTU >> PAGE_SHIFT];
| ^~~~~~~~~
With CONFIG_PAGE_SIZE_16KB=y, PAGE_SHIFT == 14, so:
#define ETH_JUMBO_MTU 9000
causes "ETH_JUMBO_MTU >> PAGE_SHIFT" to be 0. Use "?: 1" to solve this build warning.
Cc: Mirko Lindner <mlindner@marvell.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: netdev@vger.kernel.org
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202309191958.UBw1cjXk-lkp@intel.com/
Reviewed-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using this node, we can obtain random numbers via
hardware random number generator.
Signed-off-by: Alexey Romanov <avromanov@sberdevices.ru>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230929102942.67985-4-avromanov@salutedevices.com
[narmstrong: fixed commit message]
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
The maple tree register cache is based on a much more modern data structure
than the rbtree cache and makes optimisation choices which are probably
more appropriate for modern systems than those made by the rbtree cache.
Signed-off-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The maple tree register cache is based on a much more modern data structure
than the rbtree cache and makes optimisation choices which are probably
more appropriate for modern systems than those made by the rbtree cache.
Signed-off-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Shubhrajyoti Datta <shubhrajyoti.datta@amd.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
