We auto-negotiate most ports in the RTL8366RB driver, but
the CPU port is hard-coded to 1Gbit, full duplex, tx and
rx pause.
This isn't very nice. People may configure speed and
duplex differently in the device tree.
Actually respect the arguments passed to the function for
the CPU port, which get passed properly after Russell's
patch "net: dsa: realtek: add phylink_get_caps implementation"
After this the link is still set up properly.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver can now use PTP if enabled but fails to link built-in
if PTP is a loadable module:
aarch64-linux-ld: drivers/net/ethernet/ti/icssg/icss_iep.o: in function `icss_iep_get_ptp_clock_idx':
icss_iep.c:(.text+0x200): undefined reference to `ptp_clock_index'
Add the usual dependency to avoid this.
Fixes: 186734c158 ("net: ti: icssg-prueth: add packet timestamping and ptp support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: MD Danish Anwar <danishanwar@ti.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PTP block supports generating PPS output signal on GPIO pin. This patch
adds the support in the PTP PHC driver using standard periodic output
interface.
User can enable/disable/configure PPS by writing to the below sysfs entry
echo perout.index start.sec start.nsec period.sec period.nsec >
/sys/class/ptp/ptp0/period
Example to generate 50% duty cycle PPS signal:
echo 0 0 0 0 500000000 > /sys/class/ptp/ptp0/period
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: Sai Krishna <saikrishnag@marvell.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet says:
====================
ipv6: round of data-races fixes
This series is inspired by one related syzbot report.
Many inet6_sk(sk) fields reads or writes are racy.
Move 1-bit fields to inet->inet_flags to provide
atomic safety. inet6_{test|set|clear|assign}_bit() helpers
could be changed later if we need to make room in inet_flags.
Also add missing READ_ONCE()/WRITE_ONCE() when
lockless readers need access to specific fields.
np->srcprefs will be handled separately to avoid merge conflicts
because a prior patch was posted for net tree.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
np->sndflow reads are racy.
Use one bit ftom atomic inet->inet_flags instead,
IPV6_FLOWINFO_SEND setsockopt() can be lockless.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most np->pmtudisc reads are racy.
Move this 3bit field on a full byte, add annotations
and make IPV6_MTU_DISCOVER setsockopt() lockless.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reads from np->rtalert_isolate are racy.
Move this flag to inet->inet_flags to fix data-races.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move np->repflow to inet->inet_flags to fix data-races.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
np->recverr is moved to inet->inet_flags to fix data-races.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move np->dontfrag flag to inet->inet_flags to fix data-races.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move np->autoflowlabel and np->autoflowlabel_set in inet->inet_flags,
to fix data-races.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move np->mc_all to an atomic flags to fix data-races.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move np->recverr_rfc4884 to an atomic flag to fix data-races.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add one missing READ_ONCE() annotation in do_ipv6_getsockopt()
and make IPV6_MINHOPCOUNT setsockopt() lockless.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
np->frag_size can be read/written without holding socket lock.
Add missing annotations and make IPV6_MTU setsockopt() lockless.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes data-races around np->mcast_hops,
and make IPV6_MULTICAST_HOPS lockless.
Note that np->mcast_hops is never negative,
thus can fit an u8 field instead of s16.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add inet6_{test|set|clear|assign}_bit() helpers.
Note that I am using bits from inet->inet_flags,
this might change in the future if we need more flags.
While solving data-races accessing np->mc_loop,
this patch also allows to implement lockless accesses
to np->mcast_hops in the following patch.
Also constify sk_mc_loop() argument.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some np->hop_limit accesses are racy, when socket lock is not held.
Add missing annotations and switch to full lockless implementation.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit:
5a5d7e9bad ("cpuidle: lib/bug: Disable rcu_is_watching() during WARN/BUG")
amended warn_slowpath_fmt() to disable preemption until the WARN splat
has been emitted.
However the commit neglected to reenable preemption in the !fmt codepath,
i.e. when a WARN splat is emitted without additional format string.
One consequence is that users may see more splats than intended. E.g. a
WARN splat emitted in a work item results in at least two extra splats:
BUG: workqueue leaked lock or atomic
(emitted by process_one_work())
BUG: scheduling while atomic
(emitted by worker_thread() -> schedule())
Ironically the point of the commit was to *avoid* extra splats. ;)
Fix it.
Fixes: 5a5d7e9bad ("cpuidle: lib/bug: Disable rcu_is_watching() during WARN/BUG")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Paul E. McKenney <paulmck@kernel.org>
Link: https://lore.kernel.org/r/3ec48fde01e4ee6505f77908ba351bad200ae3d1.1694763684.git.lukas@wunner.de
The x86 boot image generation tool assign a default value to startup_64
and subsequently parses the actual value from zoffset.h but it never
actually uses the value anywhere. So remove this code.
This change has no impact on the resulting bzImage binary.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20230912090051.4014114-25-ardb@google.com
The root device defaults to 0,0 and is no longer configurable at build
time [0], so there is no need for the build tool to ever write to this
field.
[0] 079f85e624 ("x86, build: Do not set the root_dev field in bzImage")
This change has no impact on the resulting bzImage binary.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20230912090051.4014114-23-ardb@google.com
Now that the EFI stub decompresses the kernel and hands over to the
decompressed image directly, there is no longer a need to provide a
decompression buffer as part of the .BSS allocation of the PE/COFF
image. It also means the PE/COFF image can be loaded anywhere in memory,
and setting the preferred image base is unnecessary. So drop the
handling of this from the header and from the build tool.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20230912090051.4014114-22-ardb@google.com
Ancient (pre-2003) x86 kernels could boot from a floppy disk straight from
the BIOS, using a small real mode boot stub at the start of the image
where the BIOS would expect the boot record (or boot block) to appear.
Due to its limitations (kernel size < 1 MiB, no support for IDE, USB or
El Torito floppy emulation), this support was dropped, and a Linux aware
bootloader is now always required to boot the kernel from a legacy BIOS.
To smoothen this transition, the boot stub was not removed entirely, but
replaced with one that just prints an error message telling the user to
install a bootloader.
As it is unlikely that anyone doing direct floppy boot with such an
ancient kernel is going to upgrade to v6.5+ and expect that this boot
method still works, printing this message is kind of pointless, and so
it should be possible to remove the logic that emits it.
Let's free up this space so it can be used to expand the PE header in a
subsequent patch.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Acked-by: H. Peter Anvin (Intel) <hpa@zytor.com>
Link: https://lore.kernel.org/r/20230912090051.4014114-21-ardb@google.com
The section header flags for alignment are documented in the PE/COFF
spec as being applicable to PE object files only, not to PE executables
such as the Linux bzImage, so let's drop them from the PE header.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20230912090051.4014114-20-ardb@google.com
The native EFI entrypoint does not take a struct boot_params from the
loader, but instead, it constructs one from scratch, using the setup
header data placed at the start of the image.
This setup header is placed in a way that permits legacy loaders to
manipulate the contents (i.e., to pass the kernel command line or the
address and size of an initial ramdisk), but EFI boot does not use it in
that way - it only copies the contents that were placed there at build
time, but EFI loaders will not (and should not) manipulate the setup
header to configure the boot. (Commit 63bf28ceb3 "efi: x86: Wipe
setup_data on pure EFI boot" deals with some of the fallout of using
setup_data in a way that breaks EFI boot.)
Given that none of the non-zero values that are copied from the setup
header into the EFI stub's struct boot_params are relevant to the boot
now that the EFI stub no longer enters via the legacy decompressor, the
copy can be omitted altogether.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20230912090051.4014114-19-ardb@google.com
Now that the EFI stub always zero inits its BSS section upon entry,
there is no longer a need to place the BSS symbols carried by the stub
into the .data section.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20230912090051.4014114-18-ardb@google.com
list_for_each_entry_rcu() takes an optional fourth argument which
allows RCU to assert that the correct lock is held. Several callers
of for_each_thread() rely on their caller to be holding the appropriate
lock, so this is a useful assertion to include.
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Joel Fernandes (Google) <joel@joelfernandes.org>
Link: https://lore.kernel.org/r/20230821134428.2504912-1-willy@infradead.org
In cs35l56_hda_read_acpi() do not return if ACPI _SUB is missing.
A missing _SUB means that the driver cannot load a system-specific
firmware, because the firmware is identified by the _SUB. But it can
fallback to a generic firmware. Unfortunately this was being handled
by immediately returning 0, which would skip the remaining ACPI
configuration in cs35l56_hda_read_acpi() and so it would not get the
RESET GPIO.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: 73cfbfa9ca ("ALSA: hda/cs35l56: Add driver for Cirrus Logic CS35L56 amplifier")
Link: https://lore.kernel.org/r/20230914152525.20829-1-rf@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Lenovo ThinkCentre M70q had boot up pop noise.
Disable power save will solve pop issue.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/315900e2efef42fd9855eacfeb443abd@realtek.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
tls.sendmsg_large and tls.sendmsg_multiple are trying to send through
the self->cfd socket (only configured with TLS_RX) and to receive through
the self->fd socket (only configured with TLS_TX), so they're not using
kTLS at all. Swap the sockets.
Fixes: 7f657d5bf5 ("selftests: tls: add selftests for TLS sockets")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor cleanup pointed out by checkpatch (repeated words, missing blank
lines) in smb2pdu.c and old header location referred to in transport.c
Signed-off-by: Steve French <stfrench@microsoft.com>
Jinjie Ruan says:
====================
net: microchip: sparx5: Fix some memory leaks in vcap_api_kunit
There are some memory leaks in vcap_api_kunit, this patchset
fixes them.
Changes in v3:
- Fix the typo in patch 3, from "export" to "vcap enabled port".
- Fix the typo in patch 4, from "vcap_dup_rule" to "vcap_alloc_rule".
Changes in v2:
- Adhere to the 80 character limit in vcap_free_caf()
- Fix kernel test robot reported warnings in test_vcap_xn_rule_creator()
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
checkpatch flagged a few places with:
WARNING: ENOTSUPP is not a SUSV4 error code, prefer EOPNOTSUPP
Also fixed minor typo
Signed-off-by: Steve French <stfrench@microsoft.com>
In cxl_port_setup_targets() the region driver validates the
configuration of auto-discovered region decoders, as well
as decoders the driver is preparing to program.
The existing calculations use the encoded interleave granularity
value to create an interleave granularity that properly fans out
when routing an x1 interleave to a greater than x1 interleave.
That all worked well, until this config came along:
Host Bridge: 2 way at 256 granularity
Switch Decoder_A: 1 way at 512
Endpoint_X: 2 way at 256
Switch Decoder_B: 1 way at 512
Endpoint_Y: 2 way at 256
When the Host Bridge interleave is greater than 1 and the root
decoder interleave is exactly 1, the region driver needs to
consider the number of targets in the region when calculating
the expected granularity.
While examining the existing logic, and trying to cover the case
above, a couple of simplifications appeared, hence this proposed
refactoring.
The first simplification is to apply the logic to the nominal
values and use the existing helper function granularity_to_eig() to
translate the desired granularity to the encoded form. This means
the comment and code regarding setting address bits is discarded.
Although that logic is not wrong, it adds a level of complexity that
is not required in the granularity selection. The eig and eiw are
indeed part of the routing instructions programmed into the decoders.
Up-level the discussion to nominal ways and granularity for clearer
analysis.
The second simplification reduces the logic to a single granularity
calculation that works for all cases. The new calculation doesn't
care if parent_iw => 1 because parent_iw is used as a multiplier.
The refactor cleans up a useless assignment of eiw made after the
iw is already calculated.
Regression testing included an examination of all of the ways and
granularity selections made during a run of the cxl_test unit tests.
There were no differences in selections before and after this patch.
Fixes: ("27b3f8d138 cxl/region: Program target lists")
Signed-off-by: Alison Schofield <alison.schofield@intel.com>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/20230822180928.117596-1-alison.schofield@intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Currently, when the region driver attaches a region to a port, it
selects the ports next available decoder to program.
With the addition of auto-discovered regions, a port decoder has
already been programmed so grabbing the next available decoder can
be a mismatch when there is more than one region using the port.
The failure appears like this with CXL DEBUG enabled:
[] cxl_core:alloc_region_ref:754: cxl region0: endpoint9: HPA order violation region0:[mem 0x14780000000-0x1478fffffff flags 0x200] vs [mem 0x880000000-0x185fffffff flags 0x200]
[] cxl_core:cxl_port_attach_region:972: cxl region0: endpoint9: failed to allocate region reference
When CXL DEBUG is not enabled, there is no failure message. The region
just never materializes. Users can suspect this issue if they know their
firmware has programmed decoders so that more than one region is using
a port. Note that the problem may appear intermittently, ie not on
every reboot.
Add a matching method for auto-discovered regions that finds a decoder
based on an HPA range. The decoder range must exactly match the region
resource parameter.
Fixes: a32320b71f ("cxl/region: Add region autodiscovery")
Signed-off-by: Alison Schofield <alison.schofield@intel.com>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Davidlohr Bueso <dave@stgolabs.net>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/20230905211007.256385-1-alison.schofield@intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
When a CRC error occurs, the HBA asserts an interrupt to indicate an
interface fatal error (PxIS.IFS). The ISR clears PxIE and PxIS, then
does error recovery. If the adapter receives another SDB FIS
with an error (PxIS.TFES) from the device before the start of the EH
recovery process, the interrupt signaling the new SDB cannot be
serviced as PxIE was cleared already. This in turn results in the HBA
inability to issue any command during the error recovery process after
setting PxCMD.ST to 1 because PxIS.TFES is still set.
According to AHCI 1.3.1 specifications section 6.2.2, fatal errors
notified by setting PxIS.HBFS, PxIS.HBDS, PxIS.IFS or PxIS.TFES will
cause the HBA to enter the ERR:Fatal state. In this state, the HBA
shall not issue any new commands.
To avoid this situation, introduce the function
ahci_port_clear_pending_irq() to clear pending interrupts before
executing a COMRESET. This follows the AHCI 1.3.1 - section 6.2.2.2
specification.
Signed-off-by: Szuying Chen <Chloe_Chen@asmedia.com.tw>
Fixes: e0bfd14997 ("[PATCH] ahci: stop engine during hard reset")
Cc: stable@vger.kernel.org
Reviewed-by: Niklas Cassel <niklas.cassel@wdc.com>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Current code charges modmem for regular trampoline, but not for struct_ops
trampoline. Add bpf_jit_[charge|uncharge]_modmem() to struct_ops so the
trampoline is charged in both cases.
Signed-off-by: Song Liu <song@kernel.org>
Link: https://lore.kernel.org/r/20230914222542.2986059-1-song@kernel.org
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
- nvme-tcp iov len fix (Varun)
- nvme-hwmon const qualifier for safety (Krzysztof)
- nvme-fc null pointer checks (Nigel)
- nvme-pci no numa node fix (Pratyush)
- nvme timeout fix for non-compliant controllers (Keith)
-----BEGIN PGP SIGNATURE-----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=WTY0
-----END PGP SIGNATURE-----
Merge tag 'nvme-6.6-2023-09-14' of git://git.infradead.org/nvme into block-6.6
Pull NVMe fixes from Keith:
"nvme fixes for Linux 6.6
- nvme-tcp iov len fix (Varun)
- nvme-hwmon const qualifier for safety (Krzysztof)
- nvme-fc null pointer checks (Nigel)
- nvme-pci no numa node fix (Pratyush)
- nvme timeout fix for non-compliant controllers (Keith)"
* tag 'nvme-6.6-2023-09-14' of git://git.infradead.org/nvme:
nvme: avoid bogus CRTO values
nvme-pci: do not set the NUMA node of device if it has none
nvme-fc: Prevent null pointer dereference in nvme_fc_io_getuuid()
nvme: host: hwmon: constify pointers to hwmon_channel_info
nvmet-tcp: pass iov_len instead of sg->length to bvec_set_page()