The FBC hardware for these platforms doesn't have access to the
bios_reserved range, so it always assumes the maximum (8mb) is used.
So avoid this range while allocating.
This solves a bunch of FIFO underruns that happen if you end up
putting the CFB in that memory range. On my machine, with 32mb of
stolen, I need a 2560x1440 mode for that.
Testcase: igt/kms_frontbuffer_tracking/fbc-* (given the right setup)
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Don't allow FBC for cases where the spec says we can't FBC.
v2:
- Just WARN_ON() the strides that should have been caught earlier
(Daniel)
- Make it a new function since I expect this to grow more.
v3:
- Document which IGT test is exercised by this.
v4:
- Implement the restrictions for gens 2-6 too (Ville).
- Fix off-by-one mistake (Ville).
Testcase: igt/kms_frontbuffer_tracking/fbc-badstride
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Always update the currrent crtc, fb and vertical offset after calling
enable_fbc. We were forgetting to do so along the failure paths when
enabling fbc synchronously. Fix this with a new helper to enable_fbc()
and update the state simultaneously.
v2: Improve commit message (Chris).
v3: Constify struct drm_framebuffer (Ville).
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The scaler_id in intel_pipe_config_compare should not be checked
when adjusting in intel_pipe_config_compare. The hw scaler id may
be changed in intel_update_pipe_config.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Alex Dai <yu.dai@intel.com>
Cc: Tom O'Rourke <Tom.O'Rourke@intel.com>
Cc: Akash Goel <akash.goel@intel.com>
Signed-off-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Reviewed-by: Alex Dai <yu.dai@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Enable TO mode for RC6 for SKL till D0 and BXT till A0.
Cc: Tom O'Rourke <Tom.O'Rourke@intel.com>
Cc: Akash Goel <akash.goel@intel.com>
Signed-off-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Reviewed-by: Alex Dai <yu.dai@intel.com>
[danvet: Fixup line continuation alignment.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
CONFIG_VMSPLIT_2G was added to mx5_defconfig by commit 06965c39b4
("ARM i.MX5: update defconfig") to fix an issue where mx53 was not
detecting the full 1GiB memory range.
However, as explained by Russell King [1] the correct fix is to select
CONFIG_HIGHMEM.
imx_v6_v7_deconfig inherited such option from mx5_defconfig.
As imx_v6_v7_deconfig has CONFIG_HIGHMEM=y, we should no longer
select such non-standard CONFIG_VMSPLIT_2G option.
[1] http://www.spinics.net/lists/arm-kernel/msg137839.html
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
hid_connect adds various strings to the buffer but they're all
conditional. You can find circumstances where nothing would be written
to it but the kernel will still print the supposedly empty buffer with
printk. This leads to corruption on the console/in the logs.
Ensure buf is initialized to an empty string.
Signed-off-by: Richard Purdie <richard.purdie@linuxfoundation.org>
[dvhart: Initialize string to "" rather than assign buf[0] = NULL;]
Cc: Jiri Kosina <jikos@kernel.org>
Cc: linux-input@vger.kernel.org
Cc: stable@vger.kernel.org
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Presently a lockdep warning is reported during creation of afu_err_buff
bin_attribute for the afu. This is caused due to the variable attr.key
not pointing to a static class key, hence the function lockdep_init_map
reports this warning:
BUG: key <some-address> not in .data!
The patch fixes this issue by calling sysfs_attr_init on the
attr_eb.attr structure before populating it with the afu_err_buff file
details. This will populate the attr.key variable with a static class
key so that lockdep_init_map stops complaining about the lockdep key not
being static.
Reported-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Vaibhav Jain <vaibhav@linux.vnet.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Reviewed-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This fixes the warnings like
"plane A assertion failure, should be disabled but not"
that on the initial modeset during boot. This can happen if
the primary plane is enabled by the firmware, but inheriting
it fails because the DMAR is active or for other reasons.
Most likely caused by
commit 36750f284b
Author: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Date: Mon Jun 1 12:49:54 2015 +0200
drm/i915: update plane state during init
Reported-by: Andreas Reis <andreas.reis@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=91429
Reported-and-tested-by: Emil Renner Berthing <kernel@esmil.dk>
Tested-by: Andreas Reis <andreas.reis@gmail.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Just to prettify the log message. Otherwise it would be <UNKNOWN>.
Signed-off-by: Daniel Martin <consume.noise@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Adds support for Microsoft Type Cover 3 with 0x07e2 product ID.
Signed-off-by: Donavan Lance <shvr@fedoraproject.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Drop CONFIG_EDAC_DEBUG ifdeffery too, while at it.
Tested-by: Loc Ho <lho@apm.com>
Cc: linux-edac@vger.kernel.org
Signed-off-by: Borislav Petkov <bp@suse.de>
This patch cleans the capmode protocol module. It removes the obsolete
function arcnet_cap_init and replaces printk with pr_info.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
This patch moves the module_init and module_exit patches to
the end of the file. It also replaces the printk with pr_info.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
WaRsDisableCoarsePowerGating: Coarse Power Gating (CPG) needs to be
disabled for platforms prior to BXT B0 and SKL GT3/GT4 till E0.
v2: Added GT3/GT4 Check.
Change-Id: Ia3c4c16e050c88d3e259f601054875c812d69c3a
Signed-off-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Reviewed-by: Alex Dai <yu.dai@intel.com>
[danvet: Align continuation properly.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It will be usefull to specify w/a that affects only SKL GT3 and GT4.
Signed-off-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Reviewed-by: Alex Dai <yu.dai@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Looks like this was introduced in:
commit d1675198ed
Author: Alex Dai <yu.dai@intel.com>
Date: Wed Aug 12 15:43:43 2015 +0100
drm/i915: Integrate GuC-based command submission
This patch assumed LRC contexts and HWS layout, which is incorrect on
platforms without execlists. This can lead to a crash in GPU error
state readout on those platforms.
I don't see a bug filed for this, but there may be one that I haven't
found.
v2: fixup offset handling for error capture fix (Dave)
Cc: Alex Dai <yu.dai@intel.com>
Reviewed-by: Dave Gordon <david.s.gordon@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
intel_modeset_readout_hw_state() seems like the more appropriate place
for populating the scanline_offset and timestamping constants than
intel_sanitize_crtc() since they are basically part of the state we
read out.
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Move the sprite/cursor plane disabling to occur in intel_sanitize_crtc()
where it belongs instead of doing it in intel_modeset_readout_hw_state().
The plane disabling was first added in
4cf0ebbd4f drm/i915: Rework plane readout.
I got the idea from some patches from Partik and/or Maarten but those
moved also the plane state readout to intel_sanitize_crtc() which isn't
quite right in my opinion.
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
References: https://bugs.freedesktop.org/show_bug.cgi?id=91910
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The dotclock is often calculated in encoder .get_config(), so we
shouldn't copy the adjusted_mode to hwmode until we have read out the
dotclock.
Gets rid of some warnings like these:
[drm:drm_calc_timestamping_constants [drm]] *ERROR* crtc 21: Can't calculate constants, dotclock = 0!
[drm:i915_get_vblank_timestamp] crtc 0 is disabled
v2: Steal Maarten's idea to move crtc->mode etc. assignment too
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=91428
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The 'sched_domain_topology' variable is only used within kernel/sched/core.c.
Make it static.
Signed-off-by: Juergen Gross <jgross@suse.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1442918939-9907-1-git-send-email-jgross@suse.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The Bspec is very clear that Live status must be checked about before
trying to read EDID over DDC channel. This patch makes sure that HDMI
EDID is read only when live status is up.
The live status doesn't seem to perform very consistent across various
platforms when tested with different monitors. The reason behind that is
some monitors are late to provide right voltage to set live_status up.
So, after getting the interrupt, for a small duration, live status reg
fluctuates, and then settles down showing the correct staus.
This is explained here in, in a rough way:
HPD line ________________
|\ T1 = Monitor Hotplug causing IRQ
| \______________________________________
| |
| |
| | T2 = Live status is stable
| | _____________________________________
| | /|
Live status _____________|_|/ |
| | |
| | |
| | |
T0 T1 T2
(Between T1 and T2 Live status fluctuates or can be even low, depending on
the monitor)
After several experiments, we have concluded that a max delay
of 30ms is enough to allow the live status to settle down with
most of the monitors. This total delay of 30ms has been split into
a resolution of 3 retries of 10ms each, for the better cases.
This delay is kept at 30ms, keeping in consideration that, HDCP compliance
expect the HPD handler to respond a plug out in 100ms, by disabling port.
v2: Adding checks for VLV/CHV as well. Reusing old ibx and g4x functions
to check digital port status. Adding a separate function to get bxt live
status (Daniel)
v3: Using intel_encoder->hpd_pin to check the live status (Siva)
Moving the live status read to intel_hdmi_probe and passing parameter
to read/not to read the edid. (me)
v4:
* Added live status check for all platforms using
intel_digital_port_connected.
* Rebased on top of Jani's DP cleanup series
* Some monitors take time in setting the live status. So retry for few
times if this is a connect HPD
v5: Removed extra "drm/i915" from commit message. Adding Shashank's sob
which was missed.
v6: Drop the (!detect_edid && !live_status check) check because for DDI
ports which are enumerated as hdmi as well as DP, we don't have a
mechanism to differentiate between DP and hdmi inside the encoder's
hot_plug. This leads to call to the hdmi's hot_plug hook for DP as well
as hdmi which leads to issues during unplug because of the above check.
v7: Make intel_digital_port_connected global in this patch, some
reformatting of while loop, adding a print when live status is not
up. (Rodrigo)
v8: Rebase it on nightly which involved skipping the hot_plug hook for now
and letting the live_status check happen in detect until the hpd handling
part is finalized (Daniel)
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Sonika Jindal <sonika.jindal@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch modifies dsi_prepare() function to support the same
modeset prepare sequence for BXT also. Main changes are:
1. BXT port control register is different than VLV.
2. BXT modeset sequence needs vdisplay and hdisplay programmed
for transcoder.
3. BXT can select PIPE for MIPI transcoders.
4. BXT needs to program register MIPI_INIT_COUNT for both the ports,
even if only one is being used.
v2: Fixed Jani's review comments. Rectified the DSI Macros to get
proper register offsets using _MIPI_PORT instead of _TRANSCODER
v3: Rebased on latest drm-nightly branch. Fixed Jani's review comments.
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch adds two new functions:
- disable_dsi_pll.
BXT DSI disable sequence and registers are
different from previous platforms.
- intel_disable_dsi_pll
wrapper function to re-use the same code for
multiple platforms. It checks platform type and
calls appropriate core pll disable function.
v2: Fixed Jani's review comments.
v3: Rebased on latest drm-nightly branch.
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch adds new functions for BXT clock and PLL programming.
They are:
1. configure_dsi_pll for BXT.
This function does the basic math and generates the divider ratio
based on requested pixclock, and program clock registers.
2. enable_dsi_pll function.
This function programs the calculated clock values on the PLL.
3. intel_enable_dsi_pll
Wrapper function to use same code for multiple platforms. It checks the
platform and calls appropriate core pll enable function.
v2: Fixed Jani's review comments. Macros are adjusted as per convention.
v3: Removed a redundant change wrt code comment.
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On BXT, We Observe timeout for forcewake request completion with 2ms polling period as given here:
[drm:fw_domains_get] ERROR render: timed out waiting for forcewake ack request.
Polling for 50ms is recommended to avoid these timeouts.
Change-Id: Ie715b0069a3049606e9602bc5e97a6511890864d
Signed-off-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Reviewed by: Alex Dai <yu.dai@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Provide atomic_read_ctrl() to mirror READ_ONCE_CTRL(), such that we can
more conveniently use atomics in control dependencies.
Since we can assume atomic_read() implies a READ_ONCE(), we must only
emit an extra smp_read_barrier_depends() in order to upgrade to
READ_ONCE_CTRL() semantics.
Requested-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Cc: oleg@redhat.com
Link: http://lkml.kernel.org/r/20150918115637.GM3604@twins.programming.kicks-ass.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This patch makes sure that atomic_{read,set}() are at least
{READ,WRITE}_ONCE().
We already had the 'requirement' that atomic_read() should use
ACCESS_ONCE(), and most archs had this, but a few were lacking.
All are now converted to use READ_ONCE().
And, by a symmetry and general paranoia argument, upgrade atomic_set()
to use WRITE_ONCE().
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: james.hogan@imgtec.com
Cc: linux-kernel@vger.kernel.org
Cc: oleg@redhat.com
Cc: will.deacon@arm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
When adding the atomic bitops, I seem to have forgotten about
atomic_long_t, fix this.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The return value of (do_)balance_runtime() is not consumed by anybody.
Make them return void.
Signed-off-by: Juri Lelli <juri.lelli@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1441188096-23021-5-git-send-email-juri.lelli@arm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
rt_mutex_waiter_less() check of task deadlines is open coded. Since this
is subject to wraparound bugs, make it use the correct helper.
Reported-by: Luca Abeni <luca.abeni@unitn.it>
Signed-off-by: Juri Lelli <juri.lelli@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1441188096-23021-4-git-send-email-juri.lelli@arm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Move dl_time_before() static definition in include/linux/sched/deadline.h
so that it can be used by different parties without being re-defined.
Reported-by: Luca Abeni <luca.abeni@unitn.it>
Signed-off-by: Juri Lelli <juri.lelli@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1441188096-23021-3-git-send-email-juri.lelli@arm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Various people reported hitting the "unpinning an unpinned lock"
warning. As it turns out there are 2 places where we take a lock out
of the middle of a stack, and in those cases it would fail to preserve
the pin_count when rebuilding the lock stack.
Reported-by: Sasha Levin <sasha.levin@oracle.com>
Reported-by: Tim Spriggs <tspriggs@apple.com>
Tested-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: davej@codemonkey.org.uk
Link: http://lkml.kernel.org/r/20150916141040.GA11639@twins.programming.kicks-ass.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Disable Turbo on steppings prior to B0 on BXT due to hangs seen during GT CPD exit.
Change-Id: I50c5c03f59f5ba092db19e17234951d89db42c6c
Signed-off-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Reviewed by: Alex Dai <yu.dai@intel.com>.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
User visible:
- Fix a segfault in 'perf probe' when removing uprobe events (Masami Hiramatsu)
- Synthesize COMM event for workloads started from the command line in 'perf
record' so that we can have the pid->comm mapping before we get the real
PERF_RECORD_COMM switching from perf to the workload (Namhyung Kim)
- Fix build tools/vm/ due to removal of tools/lib/api/fs/debugfs.h
(Arnaldo Carvalho de Melo)
Developer stuff:
- Fix the make tarball targets by including the recently added err.h header in
the perf MANIFEST file (Jiri Olsa)
- Don't assume that the event parser returns a non empty evlist (Wang Nan)
- Add way to disambiguate feature detection state files, needed to use
tools/build feature detection for multiple components in a single O= output
dir, which will be the case with tools/perf/ and tools/lib/bpf/
(Arnaldo Carvalho de Melo)
- Fixup FEATURE_{TESTS,DISPLAY} inversion in tools/lib/bpf/ (Arnaldo Carvalho de Melo)
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=6DJ/
-----END PGP SIGNATURE-----
Merge tag 'perf-core-for-mingo' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux into perf/core
Pull perf/core improvements and fixes from Arnaldo Carvalho de Melo:
User visible changes:
- Fix a segfault in 'perf probe' when removing uprobe events. (Masami Hiramatsu)
- Synthesize COMM event for workloads started from the command line in 'perf
record' so that we can have the pid->comm mapping before we get the real
PERF_RECORD_COMM switching from perf to the workload. (Namhyung Kim)
- Fix build tools/vm/ due to removal of tools/lib/api/fs/debugfs.h.
(Arnaldo Carvalho de Melo)
Infrastructure changes:
- Fix the make tarball targets by including the recently added err.h header in
the perf MANIFEST file. (Jiri Olsa)
- Don't assume that the event parser returns a non empty evlist. (Wang Nan)
- Add way to disambiguate feature detection state files, needed to use
tools/build feature detection for multiple components in a single O= output
dir, which will be the case with tools/perf/ and tools/lib/bpf/.
(Arnaldo Carvalho de Melo)
- Fixup FEATURE_{TESTS,DISPLAY} inversion in tools/lib/bpf/. (Arnaldo Carvalho de Melo)
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Modified HAS_CSR macro defination which earlier only supported
for skl, now added support for BXT.
v1: Initial version.
v2: Instaed of skylake/broxton check added gen9 check alone based
on review comment from Sunil.
Cc: Vetter, Daniel <daniel.vetter@intel.com>
Cc: Damien Lespiau <damien.lespiau@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Sunil Kamath <sunil.kamath@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Added stepping info in intel_csr.c which is required to extract
specific firmware from packaged dmc firmware.
Stepping info is aligned with current bspec info.
Cc: Vetter, Daniel <daniel.vetter@intel.com>
Cc: Damien Lespiau <damien.lespiau@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Sunil Kamath <sunil.kamath@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Broxton also has dmc to manage low-power display engine state.
Path of the firmware added in intel_csr.c.
Naming convention followed as <platform>_dmc_<api-version>.bin
v1: Initial version.
v2: Commit description added based on review comment from Sunil.
Cc: Damien Lespiau <damien.lespiau@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Sunil Kamath <sunil.kamath@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With CONFIG_CPUMASK_OFFSTACK=y cpumask_var_t is a pointer to a CPU mask.
Replace the incorrect type for node_to_cpumask_map with cpumask_t.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
On HSW at least (still testing other platforms, but should be harmless
elsewhere), the DSL reg reads back as 0 when read around vblank start
time. This ends up confusing the atomic start/end checking code, since
it causes the update to appear as if it crossed a frame count boundary.
Avoid the problem by making sure we don't return scanline_offset from
the get_crtc_scanline function. In moving the code there, I add to add
an additional delay since it could be called and have a legitimate 0
result for some time (depending on the pixel clock).
v2: move hsw dsl read hack to get_crtc_scanline (Ville)
v3: use break instead of goto (Ville)
update comment with workaround details (Ville)
References: https://bugs.freedesktop.org/show_bug.cgi?id=91579
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
This patch replaces all magic numbers in the driver with
proper named macros. For the case of XTOcfg and STARTIOcmd
it introduces the new macros.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
This patch changes the macro definitions to match the C99
formating. This improves the readability.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
The word length macros are unused. Remove them.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
