When punching a file hole if we endup only zeroing parts of a page,
because the start offset isn't a multiple of the sector size or the
start offset and length fall within the same page, we were not updating
the inode item. This prevented an fsync from doing anything, if no other
file changes happened in the current transaction, because the fields
in btrfs_inode used to check if the inode needs to be fsync'ed weren't
updated.
This issue is easy to reproduce and the following excerpt from the
xfstest case I made shows how to trigger it:
_scratch_mkfs >> $seqres.full 2>&1
_init_flakey
_mount_flakey
# Create our test file.
$XFS_IO_PROG -f -c "pwrite -S 0x22 -b 16K 0 16K" \
$SCRATCH_MNT/foo | _filter_xfs_io
# Fsync the file, this makes btrfs update some btrfs inode specific fields
# that are used to track if the inode needs to be written/updated to the fsync
# log or not. After this fsync, the new values for those fields indicate that
# a subsequent fsync does not need to touch the fsync log.
$XFS_IO_PROG -c "fsync" $SCRATCH_MNT/foo
# Force a commit of the current transaction. After this point, any operation
# that modifies the data or metadata of our file, should update those fields in
# the btrfs inode with values that make the next fsync operation write to the
# fsync log.
sync
# Punch a hole in our file. This small range affects only 1 page.
# This made the btrfs hole punching implementation write only some zeroes in
# one page, but it did not update the btrfs inode fields used to determine if
# the next fsync needs to write to the fsync log.
$XFS_IO_PROG -c "fpunch 8000 4K" $SCRATCH_MNT/foo
# Another variation of the previously mentioned case.
$XFS_IO_PROG -c "fpunch 15000 100" $SCRATCH_MNT/foo
# Now fsync the file. This was a no-operation because the previous hole punch
# operation didn't update the inode's fields mentioned before, so they remained
# with the values they had after the first fsync - that is, they indicate that
# it is not needed to write to fsync log.
$XFS_IO_PROG -c "fsync" $SCRATCH_MNT/foo
echo "File content before:"
od -t x1 $SCRATCH_MNT/foo
# Simulate a crash/power loss.
_load_flakey_table $FLAKEY_DROP_WRITES
_unmount_flakey
# Enable writes and mount the fs. This makes the fsync log replay code run.
_load_flakey_table $FLAKEY_ALLOW_WRITES
_mount_flakey
# Because the last fsync didn't do anything, here the file content matched what
# it was after the first fsync, before the holes were punched, and not what it
# was after the holes were punched.
echo "File content after:"
od -t x1 $SCRATCH_MNT/foo
This issue has been around since 2012, when the punch hole implementation
was added, commit 2aaa665581 ("Btrfs: add hole punching").
A test case for xfstests follows soon.
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: Liu Bo <bo.li.liu@oracle.com>
Signed-off-by: Chris Mason <clm@fb.com>
Our gluster boxes were hitting a problem where they'd run out of space when
updating the block group cache and therefore wouldn't be able to update the free
space inode. This is a problem because this is how we invalidate the cache and
protect ourselves from errors further down the stack, so if this fails we have
to abort the transaction so we make sure we don't end up with stale free space
cache. Thanks,
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: Chris Mason <clm@fb.com>
We can have multiple fsync operations against the same file during the
same transaction and they can collect the same ordered extents while they
don't complete (still accessible from the inode's ordered tree). If this
happens, those ordered extents will never get their reference counts
decremented to 0, leading to memory leaks and inode leaks (an iput for an
ordered extent's inode is scheduled only when the ordered extent's refcount
drops to 0). The following sequence diagram explains this race:
CPU 1 CPU 2
btrfs_sync_file()
btrfs_sync_file()
mutex_lock(inode->i_mutex)
btrfs_log_inode()
btrfs_get_logged_extents()
--> collects ordered extent X
--> increments ordered
extent X's refcount
btrfs_submit_logged_extents()
mutex_unlock(inode->i_mutex)
mutex_lock(inode->i_mutex)
btrfs_sync_log()
btrfs_wait_logged_extents()
--> list_del_init(&ordered->log_list)
btrfs_log_inode()
btrfs_get_logged_extents()
--> Adds ordered extent X
to logged_list because
at this point:
list_empty(&ordered->log_list)
&& test_bit(BTRFS_ORDERED_LOGGED,
&ordered->flags) == 0
--> Increments ordered extent
X's refcount
--> check if ordered extent's io is
finished or not, start it if
necessary and wait for it to finish
--> sets bit BTRFS_ORDERED_LOGGED
on ordered extent X's flags
and adds it to trans->ordered
btrfs_sync_log() finishes
btrfs_submit_logged_extents()
btrfs_log_inode() finishes
mutex_unlock(inode->i_mutex)
btrfs_sync_file() finishes
btrfs_sync_log()
btrfs_wait_logged_extents()
--> Sees ordered extent X has the
bit BTRFS_ORDERED_LOGGED set in
its flags
--> X's refcount is untouched
btrfs_sync_log() finishes
btrfs_sync_file() finishes
btrfs_commit_transaction()
--> called by transaction kthread for e.g.
btrfs_wait_pending_ordered()
--> waits for ordered extent X to
complete
--> decrements ordered extent X's
refcount by 1 only, corresponding
to the increment done by the fsync
task ran by CPU 1
In the scenario of the above diagram, after the transaction commit,
the ordered extent will remain with a refcount of 1 forever, leaking
the ordered extent structure and preventing the i_count of its inode
from ever decreasing to 0, since the delayed iput is scheduled only
when the ordered extent's refcount drops to 0, preventing the inode
from ever being evicted by the VFS.
Fix this by using the flag BTRFS_ORDERED_LOGGED differently. Use it to
mean that an ordered extent is already being processed by an fsync call,
which will attach it to the current transaction, preventing it from being
collected by subsequent fsync operations against the same inode.
This race was introduced with the following change (added in 3.19 and
backported to stable 3.18 and 3.17):
Btrfs: make sure logged extents complete in the current transaction V3
commit 50d9aa99bd
I ran into this issue while running xfstests/generic/113 in a loop, which
failed about 1 out of 10 runs with the following warning in dmesg:
[ 2612.440038] WARNING: CPU: 4 PID: 22057 at fs/btrfs/disk-io.c:3558 free_fs_root+0x36/0x133 [btrfs]()
[ 2612.442810] Modules linked in: btrfs crc32c_generic xor raid6_pq nfsd auth_rpcgss oid_registry nfs_acl nfs lockd grace fscache sunrpc loop processor parport_pc parport psmouse therma
l_sys i2c_piix4 serio_raw pcspkr evdev microcode button i2c_core ext4 crc16 jbd2 mbcache sd_mod sg sr_mod cdrom virtio_scsi ata_generic virtio_pci ata_piix virtio_ring libata virtio flo
ppy e1000 scsi_mod [last unloaded: btrfs]
[ 2612.452711] CPU: 4 PID: 22057 Comm: umount Tainted: G W 3.19.0-rc5-btrfs-next-4+ #1
[ 2612.454921] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.7.5-0-ge51488c-20140602_164612-nilsson.home.kraxel.org 04/01/2014
[ 2612.457709] 0000000000000009 ffff8801342c3c78 ffffffff8142425e ffff88023ec8f2d8
[ 2612.459829] 0000000000000000 ffff8801342c3cb8 ffffffff81045308 ffff880046460000
[ 2612.461564] ffffffffa036da56 ffff88003d07b000 ffff880046460000 ffff880046460068
[ 2612.463163] Call Trace:
[ 2612.463719] [<ffffffff8142425e>] dump_stack+0x4c/0x65
[ 2612.464789] [<ffffffff81045308>] warn_slowpath_common+0xa1/0xbb
[ 2612.466026] [<ffffffffa036da56>] ? free_fs_root+0x36/0x133 [btrfs]
[ 2612.467247] [<ffffffff810453c5>] warn_slowpath_null+0x1a/0x1c
[ 2612.468416] [<ffffffffa036da56>] free_fs_root+0x36/0x133 [btrfs]
[ 2612.469625] [<ffffffffa036f2a7>] btrfs_drop_and_free_fs_root+0x93/0x9b [btrfs]
[ 2612.471251] [<ffffffffa036f353>] btrfs_free_fs_roots+0xa4/0xd6 [btrfs]
[ 2612.472536] [<ffffffff8142612e>] ? wait_for_completion+0x24/0x26
[ 2612.473742] [<ffffffffa0370bbc>] close_ctree+0x1f3/0x33c [btrfs]
[ 2612.475477] [<ffffffff81059d1d>] ? destroy_workqueue+0x148/0x1ba
[ 2612.476695] [<ffffffffa034e3da>] btrfs_put_super+0x19/0x1b [btrfs]
[ 2612.477911] [<ffffffff81153e53>] generic_shutdown_super+0x73/0xef
[ 2612.479106] [<ffffffff811540e2>] kill_anon_super+0x13/0x1e
[ 2612.480226] [<ffffffffa034e1e3>] btrfs_kill_super+0x17/0x23 [btrfs]
[ 2612.481471] [<ffffffff81154307>] deactivate_locked_super+0x3b/0x50
[ 2612.482686] [<ffffffff811547a7>] deactivate_super+0x3f/0x43
[ 2612.483791] [<ffffffff8116b3ed>] cleanup_mnt+0x59/0x78
[ 2612.484842] [<ffffffff8116b44c>] __cleanup_mnt+0x12/0x14
[ 2612.485900] [<ffffffff8105d019>] task_work_run+0x8f/0xbc
[ 2612.486960] [<ffffffff810028d8>] do_notify_resume+0x5a/0x6b
[ 2612.488083] [<ffffffff81236e5b>] ? trace_hardirqs_on_thunk+0x3a/0x3f
[ 2612.489333] [<ffffffff8142a17f>] int_signal+0x12/0x17
[ 2612.490353] ---[ end trace 54a960a6bdcb8d93 ]---
[ 2612.557253] VFS: Busy inodes after unmount of sdb. Self-destruct in 5 seconds. Have a nice day...
Kmemleak confirmed the ordered extent leak (and btrfs inode specific
structures such as delayed nodes):
$ cat /sys/kernel/debug/kmemleak
unreferenced object 0xffff880154290db0 (size 576):
comm "btrfsck", pid 21980, jiffies 4295542503 (age 1273.412s)
hex dump (first 32 bytes):
01 40 00 00 01 00 00 00 b0 1d f1 4e 01 88 ff ff .@.........N....
00 00 00 00 00 00 00 00 c8 0d 29 54 01 88 ff ff ..........)T....
backtrace:
[<ffffffff8141d74d>] kmemleak_update_trace+0x4c/0x6a
[<ffffffff8122f2c0>] radix_tree_node_alloc+0x6d/0x83
[<ffffffff8122fb26>] __radix_tree_create+0x109/0x190
[<ffffffff8122fbdd>] radix_tree_insert+0x30/0xac
[<ffffffffa03b9bde>] btrfs_get_or_create_delayed_node+0x130/0x187 [btrfs]
[<ffffffffa03bb82d>] btrfs_delayed_delete_inode_ref+0x32/0xac [btrfs]
[<ffffffffa0379dae>] __btrfs_unlink_inode+0xee/0x288 [btrfs]
[<ffffffffa037c715>] btrfs_unlink_inode+0x1e/0x40 [btrfs]
[<ffffffffa037c797>] btrfs_unlink+0x60/0x9b [btrfs]
[<ffffffff8115d7f0>] vfs_unlink+0x9c/0xed
[<ffffffff8115f5de>] do_unlinkat+0x12c/0x1fa
[<ffffffff811601a7>] SyS_unlinkat+0x29/0x2b
[<ffffffff81429e92>] system_call_fastpath+0x12/0x17
[<ffffffffffffffff>] 0xffffffffffffffff
unreferenced object 0xffff88014ef11db0 (size 576):
comm "rm", pid 22009, jiffies 4295542593 (age 1273.052s)
hex dump (first 32 bytes):
02 00 00 00 01 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 c8 1d f1 4e 01 88 ff ff ...........N....
backtrace:
[<ffffffff8141d74d>] kmemleak_update_trace+0x4c/0x6a
[<ffffffff8122f2c0>] radix_tree_node_alloc+0x6d/0x83
[<ffffffff8122fb26>] __radix_tree_create+0x109/0x190
[<ffffffff8122fbdd>] radix_tree_insert+0x30/0xac
[<ffffffffa03b9bde>] btrfs_get_or_create_delayed_node+0x130/0x187 [btrfs]
[<ffffffffa03bb82d>] btrfs_delayed_delete_inode_ref+0x32/0xac [btrfs]
[<ffffffffa0379dae>] __btrfs_unlink_inode+0xee/0x288 [btrfs]
[<ffffffffa037c715>] btrfs_unlink_inode+0x1e/0x40 [btrfs]
[<ffffffffa037c797>] btrfs_unlink+0x60/0x9b [btrfs]
[<ffffffff8115d7f0>] vfs_unlink+0x9c/0xed
[<ffffffff8115f5de>] do_unlinkat+0x12c/0x1fa
[<ffffffff811601a7>] SyS_unlinkat+0x29/0x2b
[<ffffffff81429e92>] system_call_fastpath+0x12/0x17
[<ffffffffffffffff>] 0xffffffffffffffff
unreferenced object 0xffff8800336feda8 (size 584):
comm "aio-stress", pid 22031, jiffies 4295543006 (age 1271.400s)
hex dump (first 32 bytes):
00 40 3e 00 00 00 00 00 00 00 8f 42 00 00 00 00 .@>........B....
00 00 01 00 00 00 00 00 00 00 01 00 00 00 00 00 ................
backtrace:
[<ffffffff8114eb34>] create_object+0x172/0x29a
[<ffffffff8141d790>] kmemleak_alloc+0x25/0x41
[<ffffffff81141ae6>] kmemleak_alloc_recursive.constprop.52+0x16/0x18
[<ffffffff81145288>] kmem_cache_alloc+0xf7/0x198
[<ffffffffa0389243>] __btrfs_add_ordered_extent+0x43/0x309 [btrfs]
[<ffffffffa038968b>] btrfs_add_ordered_extent_dio+0x12/0x14 [btrfs]
[<ffffffffa03810e2>] btrfs_get_blocks_direct+0x3ef/0x571 [btrfs]
[<ffffffff81181349>] do_blockdev_direct_IO+0x62a/0xb47
[<ffffffff8118189a>] __blockdev_direct_IO+0x34/0x36
[<ffffffffa03776e5>] btrfs_direct_IO+0x16a/0x1e8 [btrfs]
[<ffffffff81100373>] generic_file_direct_write+0xb8/0x12d
[<ffffffffa038615c>] btrfs_file_write_iter+0x24b/0x42f [btrfs]
[<ffffffff8118bb0d>] aio_run_iocb+0x2b7/0x32e
[<ffffffff8118c99a>] do_io_submit+0x26e/0x2ff
[<ffffffff8118ca3b>] SyS_io_submit+0x10/0x12
[<ffffffff81429e92>] system_call_fastpath+0x12/0x17
CC: <stable@vger.kernel.org> # 3.19, 3.18 and 3.17
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Chris Mason <clm@fb.com>
In commit b4eef9b36d, we started to use hwapic_isr_update() != NULL
instead of kvm_apic_vid_enabled(vcpu->kvm). This didn't work because
SVM had it defined and "apicv" path in apic_{set,clear}_isr() does not
change apic->isr_count, because it should always be 1. The initial
value of apic->isr_count was based on kvm_apic_vid_enabled(vcpu->kvm),
which is always 0 for SVM, so KVM could have injected interrupts when it
shouldn't.
Fix it by implicitly setting SVM's hwapic_isr_update to NULL and make the
initial isr_count depend on hwapic_isr_update() for good measure.
Fixes: b4eef9b36d ("kvm: x86: vmx: NULL out hwapic_isr_update() in case of !enable_apicv")
Reported-and-tested-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
- fix a read-balance problem that was reported 2 years ago, but
that I never noticed the report :-(
- fix for rare RAID6 problem causing incorrect bitmap updates when
two devices fail.
- add __ATTR_PREALLOC annotation now that it is possible.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=CaGN
-----END PGP SIGNATURE-----
Merge tag 'md/4.0-fixes' of git://neil.brown.name/md
Pull md fixes from Neil Brown:
"Three md fixes:
- fix a read-balance problem that was reported 2 years ago, but that
I never noticed the report :-(
- fix for rare RAID6 problem causing incorrect bitmap updates when
two devices fail.
- add __ATTR_PREALLOC annotation now that it is possible"
* tag 'md/4.0-fixes' of git://neil.brown.name/md:
md: mark some attributes as pre-alloc
raid5: check faulty flag for array status during recovery.
md/raid1: fix read balance when a drive is write-mostly.
This is just a single patch to fix the KSTK_EIP() and KSTK_ESP() macros
for metag which have always been erronously returning the PC and stack
pointer of the task's kernel context rather than from its user context
saved at entry from userland into the kernel, which affects the contents
of /proc/<pid>/maps and /proc/<pid>/stat.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=1+sf
-----END PGP SIGNATURE-----
Merge tag 'metag-fixes-v4.0-1' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/metag
Pull arch/metag fix from James Hogan:
"This is just a single patch to fix the KSTK_EIP() and KSTK_ESP()
macros for metag which have always been erronously returning the PC
and stack pointer of the task's kernel context rather than from its
user context saved at entry from userland into the kernel, which
affects the contents of /proc/<pid>/maps and /proc/<pid>/stat"
* tag 'metag-fixes-v4.0-1' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/metag:
metag: Fix KSTK_EIP() and KSTK_ESP() macros
Eric W. Biederman says:
====================
Neighbour table and ax25 cleanups
While looking at the neighbour table to what it would take to allow
using next hops in a different address family than the current packets
I found a partial resolution for my issues and I stumbled upon some
work that makes the neighbour table code easier to understand and
maintain.
Long ago in a much younger kernel ax25 found a hack to use
dev_rebuild_header to transmit it's packets instead of going through
what today is ndo_start_xmit.
When the neighbour table was rewritten into it's current form the ax25
code was such a challenge that arp_broken_ops appeard in arp.c and
neigh_compat_output appeared in neighbour.c to keep the ax25 hack alive.
With a little bit of work I was able to remove some of the hack that
is the ax25 transmit path for ip packets and to isolate what remains
into a slightly more readable piece of code in ax25_ip.c. Removing the
need for the generic code to worry about ax25 special cases.
After cleaning up the old ax25 hacks I also performed a little bit of
work on neigh_resolve_output to remove the need for a dst entry and to
ensure cached headers get a deterministic protocol value in their cached
header. This guarantees that a cached header will not be different
depending on which protocol of packet is transmitted, and it allows
packets to be transmitted that don't have a dst entry. There remains
a small amount of code that takes advantage of when packets have a dst
entry but that is something different.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Having a dst helps a little bit for teql but is fundamentally
unnecessary and there are code paths where a dst is not available that
it would be nice to use the neighbour cache.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Add protocol to neigh_tbl so that dst->ops->protocol is not needed
- Acquire the device from neigh->dev
This results in a neigh_hh_init that will cache the samve values
regardless of the packets flowing through it.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are no more callers so kill this function.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that there are no more users kill dev_rebuild_header and all of it's
implementations.
This is long overdue.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Have ax25_neigh_output perform ordinary arp resolution before calling
ax25_neigh_xmit.
Call dev_hard_header in ax25_neigh_output with a destination address so
it will not fail, and the destination mac address will not need to be
set in ax25_neigh_xmit.
Remove arp_find from ax25_neigh_xmit (the ordinary arp resolution added
to ax25_neigh_output removes the need for calling arp_find).
Document how close ax25_neigh_output is to neigh_resolve_output.
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-hams@vger.kernel.org
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Rename ax25_rebuild_header to ax25_neigh_xmit and call it from
ax25_neigh_output directly. The rename is to make it clear
that this is not a rebuild_header operation.
- Remove ax25_rebuild_header from ax25_header_ops.
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-hams@vger.kernel.org
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only caller is now is ax25_neigh_construct so move
neigh_compat_output into ax25_ip.c make it static and rename it
ax25_neigh_output.
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-hams@vger.kernel.org
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The special case has been pushed out into ax25_neigh_construct so there
is no need to keep this code in arp.c
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
AX25 already has it's own private arp cache operations to isolate
it's abuse of dev_rebuild_header to transmit packets. Add a function
ax25_neigh_construct that will allow all of the ax25 devices to
force using these operations, so that the generic arp code does
not need to.
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-hams@vger.kernel.org
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only user is in ax25_ip.c so stop exporting these functions.
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-hams@vger.kernel.org
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The two sets of header operations are functionally identical remove
the duplicate definition.
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-hams@vger.kernel.org
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The two sets of header operations are functionally identical remove the
duplicate definition.
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-hams@vger.kernel.org
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Patterned after the similar code in net/rom this turns out
to be a trivial obviously correct transmformation.
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-hams@vger.kernel.org
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not setting the destination address is a bug that I suspect causes no
problems today, as only the arp code seems to call dev_hard_header and
the description I have of rose is that it is expected to be used with a
static neigbour table.
I have derived the offset and the length of the rose destination address
from rose_rebuild_header where arp_find calls neigh_ha_snapshot to set
the destination address.
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-hams@vger.kernel.org
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the unlikely (impossible?) event that we attempt to transmit
an ax25 packet over a non-ax25 device free the skb so we don't
leak it.
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-hams@vger.kernel.org
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/input/mouse/cyapa_gen5.c: In function ‘cyapa_gen5_read_idac_data’:
drivers/input/mouse/cyapa_gen5.c:1876: warning: ‘max_element_cnt’ may be used uninitialized in this function
drivers/input/mouse/cyapa_gen5.c:1873: warning: ‘offset’ may be used uninitialized in this function
If *data_size is non-zero, and idac_data_type contains an unknown type,
max_element_cnt and offset will be uninitialized, and the loop will
process non-existing data.
However, this cannot happen (for now), as there's a test for unknown
types at the top of cyapa_gen5_read_idac_data().
As no "if ... else if ..." is used in other places, remove the
superfluous "if" to silence the compiler warning.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Dudley Du <dudl@cypress.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Use asm/unaligned.h instead of linux/unaligned/access_ok.h header file to
fix compiling issues such as following while doing cross platform
compiling:
"include/linux/unaligned/access_ok.h:7:19: error: redefinition of
'get_unaligned_le16'
...
include/linux/unaligned/le_struct.h:6:19: note: previous definition of
'get_unaligned_le16' was here".
Reported-by: kbuild test robot <kbuild-all@01.org>
Signed-off-by: Dudley Du <dudl@cypress.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The probe function open coded a bad variant of devm_gpiod_get_optional
using devm_gpiod_get and just ignoring all errors.
In contrast to that devm_gpiod_get_optional returns NULL if there was no
corresponding gpio specified in the device tree (or ACPI table) and
fails if there is an error (or GPIOLIB is not enabled).
Moreover since 39b2bbe3d7 (gpio: add flags argument to gpiod_get*()
functions) which appeared in v3.17-rc1, the gpiod_get* functions take an
additional parameter that allows to specify direction and initial value
for output which allows some simplification.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
This reverts commit 74390aa556 ("perf: Remove the extra validity check
on nr_pages")
nr_pages equals to number of pages - 1 in perf_mmap. So nr_pages = 0 is
valid.
So the nr_pages != 0 && !is_power_of_2(nr_pages) are all
needed for checking. Otherwise, for example, perf test 6 failed.
# perf test 6
6: x86 rdpmc test :Error:
mmap() syscall returned with (Invalid argument)
FAILED!
Signed-off-by: Kan Liang <kan.liang@intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Kaixu Xia <xiakaixu@huawei.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1425280466-7830-1-git-send-email-kan.liang@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Move the fallback code path in cpuidle_idle_call() to the end of the
function to avoid jumping to a label in an if () branch.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Since commit 1c6c69525b ("genirq: Reject
bogus threaded irq requests") threaded IRQs without a primary handler
need to be requested with IRQF_ONESHOT, otherwise the request may fail.
Generated by: scripts/coccinelle/misc/irqf_oneshot.cocci
Signed-off-by: Valentin Rothberg <Valentin.Rothberg@lip6.fr>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Or Gerlitz says:
====================
Mellanox driver fixes
Two small fixes, please apply to net.
Both patches should go to 3.19.y too.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Packets which are sent from the selftest (ethtool) flow,
should not be passed to GRO stack but rather dropped by
the driver after validation. To achieve that, we disable
GRO for the duration of the selftest.
Fixes: dd65beac48 ("net/mlx4_en: Extend usage of napi_gro_frags")
Reported-by: Carol Soto <clsoto@linux.vnet.ibm.com>
Signed-off-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bit mask for currently supported driver features (MLX4_UPDATE_QP_SUPPORTED_ATTRS)
of the update-qp command was defined twice (using enum value and pre-processor
define directive) and wrong.
The return value of the call to mlx4_update_qp() from within the SRIOV
resource-tracker was wrongly voided down.
Fix both issues.
issue: none
Fixes: 09e05c3f78 ('net/mlx4: Set vlan stripping policy by the right command')
Fixes: ce8d9e0d67 ('net/mlx4_core: Add UPDATE_QP SRIOV wrapper support')
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The handling of VIDIOC_G/S_PRIORITY is now entirely done by the V4L2
core, so we can drop the g/s_priority ioctl ops.
We do have to make sure though that when S_PRIORITY is called we check
that the driver used struct v4l2_fh. This check can be removed once all
drivers are converted to that structure.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
By using struct v4l2_fh both the prio handling and the linked list
implementation in pvrusb2 can be removed since both are now done in
the v4l2 core if you use struct v4l2_fh.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Masami noted that it would be better to hide the remaining CONFIG_BPF_SYSCALL-only
function declarations within the BPF header ifdef, w/o else path dummy alternatives
since these functions are not supposed to have a user outside of CONFIG_BPF_SYSCALL.
Suggested-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Reference: http://article.gmane.org/gmane.linux.kernel.api/8658
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
To keep V4L2 drivers that did not yet convert to unlocked_ioctl happy,
the v4l2 core had a .ioctl file operation that took a V4L2 lock.
The last drivers are now converted to unlocked_ioctl, so all this
old code can now be removed.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The V4L2 core will warn if this is not done. Unfortunately this driver
wasn't updated.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Instead of .ioctl use unlocked_ioctl. This allows us to finally remove
the old .ioctl op.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Switch this driver over to the V4L2 core locking mechanism in preparation
for switching to unlocked_ioctl. Suggested by Laurent Pinchart.
This patch introduces a new mutex at the struct uvc_video level and
drops the old mutex at the queue level. The new lock is now used for all
ioctl locking and in the release file operation (the driver always has
to take care of locking in file operations, the core only serializes
ioctls).
Note that the mmap and get_unmapped_area file operations no longer take
a lock. Commit f035eb4e97 fixed a AB-BA
deadlock by moving all the locking down into vb2, so the mmap and
get_unmapped_area file operations should no longer do any locking before
calling into vb2.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This driver does its own locking, so there is no need to use
ioctl instead of unlocked_ioctl.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As far as I can tell pvrusb2 does its own locking, so there is
no need to use .ioctl.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
It is confusing which parts of the driver are adv7604 specific, adv7611
specific or common for both. This patch renames any adv7604 prefixes (both
for functions and defines) to adv76xx whenever they are common.
Signed-off-by: Pablo Anton <pablo.anton@vodalys-labs.com>
Signed-off-by: Jean-Michel Hautbois <jean-michel.hautbois@vodalys.com>
[hans.verkuil@cisco.com: rebased and renamed ADV76xx_fsc to ADV76XX_FSC]
[hans.verkuil@cisco.com: kept the existing adv7604 driver name]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
In the gpio bindings documents it is requested to use the marco's in
include/dt-bindings/gpio/gpio.h whenever possible. The gpios in the led
drivers don't seem to form an exception, so update the example in the
document bindings.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
A small batch with accumulated updates in nf-next, mostly IPVS updates,
they are:
1) Add 64-bits stats counters to IPVS, from Julian Anastasov.
2) Move NETFILTER_XT_MATCH_ADDRTYPE out of NETFILTER_ADVANCED as docker
seem to require this, from Anton Blanchard.
3) Use boolean instead of numeric value in set_match_v*(), from
coccinelle via Fengguang Wu.
4) Allows rescheduling of new connections in IPVS when port reuse is
detected, from Marcelo Ricardo Leitner.
5) Add missing bits to support arptables extensions from nft_compat,
from Arturo Borrero.
Patrick is preparing a large batch to enhance the set infrastructure,
named expressions among other things, that should follow up soon after
this batch.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Both sk_attach_filter() and sk_attach_bpf() are setting up sk_filter,
charging skmem and attaching it to the socket after we got the eBPF
prog up and ready. Lets refactor that into a common helper.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add handling for timeout case.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
wait_for_completion_timeout() returns unsigned long not int. This assigns
the return value to an appropriately typed variable (also helps keep
static code checkers happy).
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Johan Hedberg says:
====================
pull request: bluetooth-next 2015-03-02
Here's the first bluetooth-next pull request targeting the 4.1 kernel:
- ieee802154/6lowpan cleanups
- SCO routing to host interface support for the btmrvl driver
- AMP code cleanups
- Fixes to AMP HCI init sequence
- Refactoring of the HCI callback mechanism
- Added shutdown routine for Intel controllers in the btusb driver
- New config option to enable/disable Bluetooth debugfs information
- Fix for early data reception on L2CAP fixed channels
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The switch_mm function does nothing in case the prev and next mm
are the same. It can happen that a crst_table_downgrade has changed
the top-level pgd in the meantime on a different CPU. Always store
the new ASCE to be picked up in entry.S.
[heiko.carstens@de.ibm.com]: Bug was introduced with git commit
53e857f308 ("s390/mm,tlb: race of lazy TLB flush vs. recreation
of TLB entries") and causes random crashes due to broken page tables
being used.
Reported-by: Dominik Vogt <vogt@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
With git commit 4d92f50249 ("s390: reintroduce diag 44 calls for
cpu_relax()") I reintroduced a non-trivial cpu_relax() variant on s390.
The difference to the previous variant however is that the new version is
an out-of-line function, which will be traced if function tracing is enabled.
Switching to different tracers includes instruction patching. Therefore this
is done within stop_machine() "context" to prevent that any function tracing
is going on while instructions are being patched.
With the new out-of-line variant of cpu_relax() this is not true anymore,
since cpu_relax() gets called in a busy loop by all waiting cpus within
stop_machine() until function patching is finished.
Therefore cpu_relax() must be marked notrace.
This fixes kernel crashes when frequently switching between "function" and
"function_graph" tracers.
Moving cpu_relax() to a header file again, doesn't work because of header
include order dependencies.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>