This patch adds support for Dialog semiconductor's DA9055 audio codec.
This has been tested on DA9055 EVB with Samsung SMDK6410 board.
Signed-off-by: Ashish Chavan <ashish.chavan@kpitcummins.com>
Signed-off-by: David Dajun Chen <david.chen@diasemi.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Convert eukrea-tlv320 to platform driver.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Apart from pure matching, the bindings also support setting the the
reset gpio line.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Cc: Alexander Sverdlin <subaparts@yandex.ru>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
There are SPI devices which need a SPI clock with active low polarity and
high inactive state.
Add the setting of the inactive state ECSPIx_CONFIGREG:SCLK CTL
according to the clock polarity ECSPIx_CONFIGREG:SCLK POL:
DT without "spi-cpol" = 0 = clock active high polarity = inactive state low
DT with "spi-cpol" = 1 = clock active low polarity = inactive state high
Signed-off-by: Knut Wohlrab <knut.wohlrab@de.bosch.com>
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This factors out the resource handling in runtime
suspend/resume and also calls it from the ordinary suspend
and resume hooks.
The semantics require that ordinary PM op suspend is called
with runtime PM in resumed mode, so that ordinary suspend
can assume that it will e.g. decrease the clock reference
counter to 0, runtime resume having previously increased it
to 1.
Cc: Vipul Kumar Samar <vipulkumar.samar@st.com>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This switches the PL022 SPI driver to use devm_* managed resources
for IRQ, clocks, ioremap and GPIO. Prior to this, the GPIOs would
even leak.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This allows /proc/vmallocinfo to show the physical address for
ioremap mappings.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The CPU hotplug callback related to writeback calls writeback_set_ratelimit()
during every state change in the hotplug sequence. This is unnecessary
since num_online_cpus() changes only once during the entire hotplug operation.
So invoke the function only once per hotplug, thereby avoiding the
unnecessary repetition of those costly calculations.
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
In some circumstances we may need to flush volume updates to the device
after switching to class W mode. Do this unconditionally to ensure that
these situations are handled.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
Follow up on commit c285f6ff6787 "firewire: remove global lock around
address handlers, convert to RCU":
- address_handler_lock no longer serializes the address handler, only
its function to serialize updates to the list of handlers remains.
Rename the lock to address_handler_list_lock.
- Callers of fw_core_remove_address_handler() must be able to sleep.
Comment on this in the API documentation.
- The counterpart fw_core_add_address_handler() is by nature something
which is used in process context. Replace spin_lock_bh() by
spin_lock() in fw_core_add_address_handler() and in
fw_core_remove_address_handler(), and document that process context
is now required for fw_core_add_address_handler().
- Extend the documentation of fw_address_callback_t.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Upper-layer handlers for inbound requests were called with a spinlock
held by firewire-core. Calling into upper layers with a lower layer
lock held is generally a bad idea.
What's more, since commit ea102d0ec4 "firewire: core: convert AR-req
handler lock from _irqsave to _bh", a caller of fw_send_request() i.e.
initiator of outbound request could no longer do that while having
interrupts disabled, if the local node was addressed by that request.
In order to make all this more flexible, convert the management of
address ranges and handlers from a global lock around readers and
writers to RCU (and a remaining global lock for writers). As a minor
side effect, handling of inbound requests at different cards and of
local requests is now no longer serialized. (There is still per-card
serialization of remote requests since firewire-ohci uses a single DMA
tasklet for inbound request events.)
In other words, address handlers are now called in an RCU read-side
critical section instead of from within a spin_lock_bh serialized
section.
(Changelog rewritten by Stefan R.)
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
discard bio hasn't data attached. We hit a BUG_ON with such bio. This makes
bio_split works for such bio.
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
. Improve listing of accessible enum perf probe variables, from Hyeoncheol Lee.
. Don't stop the build if the audit libraries are not installed, fix from Namhyung Kim.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.14 (GNU/Linux)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=98/I
-----END PGP SIGNATURE-----
Merge tag 'perf-core-for-mingo' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux into perf/core
Pull perf/core improvements and fixes from Arnaldo Carvalho de Melo:
* Improve listing of accessible enum perf probe variables, from Hyeoncheol Lee.
* Don't stop the build if the audit libraries are not installed, fix from Namhyung Kim.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The code was using a homegrown method of looking up the offset
from the irq domain, not to be encouraged. Use the proper
irq_find_mapping() call instead.
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch initializes the optional irq_chip pointer gc in sirfsoc
pinctrl_gpio_range.
Signed-off-by: Baohua Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
sirfsoc_gpio_set_input() is called in those functions which have
held the spinlock, so delete the duplicated locking.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We always use pinctrl_request_gpio() to get GPIO, If we don't have these
missing pins in the pin list, gpio_request and related operations will fail
for them.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Adds support for displaying the individual pin h/w config state.
Signed-off-by: Matt Porter <mporter@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This defines the proper sleep states for all the I2C pins of
the MOP500 DB8500 ASIC setting.
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Patrice Chotard <patrice.chotard@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Both dpi.c and sdi.c use strcmp(), but do not include string.h. With
some Kconfig options string.h is included implicitly, but with some
other the compilation fails:
drivers/video/omap2/dss/dpi.c:407:5: error: implicit declaration of
function 'strcmp'
Include string.h in both dpi.c and sdi.c
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
As TLB shootdown requests to other CPU cores are now using function call
interrupts, TLB shootdowns entry in /proc/interrupts is always shown as 0.
This behavior change was introduced by commit 52aec3308d ("x86/tlb:
replace INVALIDATE_TLB_VECTOR by CALL_FUNCTION_VECTOR").
This patch reverts TLB shootdowns entry in /proc/interrupts to count TLB
shootdowns separately from the other function call interrupts.
Signed-off-by: Tomoki Sekiyama <tomoki.sekiyama.qu@hitachi.com>
Link: http://lkml.kernel.org/r/20120926021128.22212.20440.stgit@hpxw
Acked-by: Alex Shi <alex.shi@intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
If a virtio device reports a QueueNumMax of 0, vring_new_virtqueue()
doesn't check this, and thanks to an unsigned (i < num - 1) loop
guard, scribbles over memory when initialising the free list.
Avoid by not trying to create zero-descriptor queues, as there's no
way to do any I/O with one.
Signed-off-by: Brian Foley <brian.foley@arm.com>
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
vm_setup_vq fails to allow VirtQueues needing only 2 pages of
storage, as it should. Found with a kernel using 64kB pages, but
can be provoked if a virtio device reports QueueNumMax where the
descriptor table and available ring fit in one page, and the used
ring on the second (<= 227 descriptors with 4kB pages and <= 3640
with 64kB pages.)
Signed-off-by: Brian Foley <brian.foley@arm.com>
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Convert a nonnegative error return code to a negative one, as returned
elsewhere in the function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Because of a sanity check in virtio_dev_remove, a buggy device can crash
kernel. And in case of rproc it's userspace so it's not a good idea.
We are unloading a driver so how bad can it be?
Be less aggressive in handling this error: if it's a driver bug,
warning once should be enough.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Everyone who selects VIRTIO is also made to select VIRTIO_RING; just make
them synonymous, since we removed the indirection layer some time ago.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Trying to enable a virtio driver (eg CONFIG_VIRTIO_BLK) is painful
because it depends on CONFIG_VIRTIO. CONFIG_VIRTIO doesn't tell you
how to turn it on (it's selected from anything which provides a virtio
bus).
This patch at least adds some documentation, visible in menuconfig, as
a hint.
Reported-by: Kent Overstreet <koverstreet@google.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
virtio network device multiqueue support reserves
vq 3 for future use (useful both for future extensions and to make it
pretty - this way receive vqs have even and transmit - odd numbers).
Make it possible to skip initialization for
specific vq numbers by specifying NULL for name.
Document this usage as well as (existing) NULL callback.
Drivers using this not coded up yet, so I simply tested
with virtio-pci and verified that this patch does
not break existing drivers.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Sometimes, virtio device need to configure irq affinity hint to maximize the
performance. Instead of just exposing the irq of a virtqueue, this patch
introduce an API to set the affinity for a virtqueue.
The api is best-effort, the affinity hint may not be set as expected due to
platform support, irq sharing or irq type. Currently, only pci method were
implemented and we set the affinity according to:
- if device uses INTX, we just ignore the request
- if device has per vq vector, we force the affinity hint
- if the virtqueues share MSI, make the affinity OR over all affinities
requested
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Instead of storing the queue index in transport-specific virtio structs,
this patch moves them to vring_virtqueue and introduces an helper to get
the value. This lets drivers simplify their management and tracing of
virtqueues.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
It is not experimental in any vaguely-sane sense.
Reported-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Devices should depend on virtio, not select it. It's supposed to be
selected by the particular driver, e.g. VIRTIO_PCI.
Make balloon depend on VIRTIO and EXPERIMENTAL
(to match description).
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Smatch complains about the inconsistent NULL checking here. Fix it to
return NULL on failure.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> (fixed accidental deletion)
We need to support both REQ_FLUSH and REQ_FUA for bio based path since
it does not get the sequencing of REQ_FUA into REQ_FLUSH that request
based drivers can request.
REQ_FLUSH is emulated by:
A) If the bio has no data to write:
1. Send VIRTIO_BLK_T_FLUSH to device,
2. In the flush I/O completion handler, finish the bio
B) If the bio has data to write:
1. Send VIRTIO_BLK_T_FLUSH to device
2. In the flush I/O completion handler, send the actual write data to device
3. In the write I/O completion handler, finish the bio
REQ_FUA is emulated by:
1. Send the actual write data to device
2. In the write I/O completion handler, send VIRTIO_BLK_T_FLUSH to device
3. In the flush I/O completion handler, finish the bio
Changes in v7:
- Using vbr->flags to trace request type
- Dropped unnecessary struct virtio_blk *vblk parameter
- Reuse struct virtblk_req in bio done function
Cahnges in v6:
- Reworked REQ_FLUSH and REQ_FUA emulatation order
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Tejun Heo <tj@kernel.org>
Cc: Shaohua Li <shli@kernel.org>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: kvm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: virtualization@lists.linux-foundation.org
Signed-off-by: Asias He <asias@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
If register_virtio_driver() fails, virtio-ports class is not destroyed.
The patch adds error handling of register_virtio_driver().
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Acked-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
pthread flag should not be -lpthread but -pthread using gcc. The -lpthread
links the external multithread library. On the other hand, the -pthread manages
both the gcc's preprocessor and linker to be able to compile with pthread.
Signed-off-by: Yoshihiro YUNOMAE <yoshihiro.yunomae.ez@hitachi.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
This patch adds a user tool, "trace agent" for sending trace data of a guest to
a Host in low overhead. This agent has the following functions:
- splice a page of ring-buffer to read_pipe without memory copying
- splice the page from write_pipe to virtio-console without memory copying
- write trace data to stdout by using -o option
- controlled by start/stop orders from a Host
Changes in v2:
- Cleanup (change fprintf() to pr_err() and an include guard)
Signed-off-by: Yoshihiro YUNOMAE <yoshihiro.yunomae.ez@hitachi.com>
Acked-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Allocate scatterlist according to the current pipe size.
This allows splicing bigger buffer if the pipe size has
been changed by fcntl.
Changes in v2:
- Just a minor fix for avoiding a confliction with previous patch.
Signed-off-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Acked-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Use generic steal operation on pipe buffer to allow stealing
ring buffer's read page from pipe buffer.
Note that this could reduce the performance of splice on the
splice_write side operation without affinity setting.
Since the ring buffer's read pages are allocated on the
tracing-node, but the splice user does not always execute
splice write side operation on the same node. In this case,
the page will be accessed from the another node.
Thus, it is strongly recommended to assign the splicing
thread to corresponding node.
Signed-off-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Wait if the port is not connected or full on splice
like as write is doing.
Signed-off-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Acked-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Add a failback memcpy path for unstealable pipe buffer.
If buf->ops->steal() fails, virtio-serial tries to
copy the page contents to an allocated page, instead
of just failing splice().
Signed-off-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Acked-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Enable to use splice_write from pipe to virtio-console port.
This steals pages from pipe and directly send it to host.
Note that this may accelerate only the guest to host path.
Changes in v2:
- Use GFP_KERNEL instead of GFP_ATOMIC in syscall context function.
Signed-off-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Acked-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
