Move the function nand_read_page_hwecc_oob_first() (previously
nand_davinci_read_page_hwecc_oob_first()) to nand_base.c, and export it
as a GPL symbol, so that it can be used by more modules.
Cc: <stable@vger.kernel.org> # v5.2
Fixes: a0ac778eb8 ("mtd: rawnand: ingenic: Add support for the JZ4740")
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211016132228.40254-4-paul@crapouillou.net
The original comment that describes the function
nand_davinci_read_page_hwecc_oob_first() is very obscure and it is hard
to understand what it is for.
Cc: <stable@vger.kernel.org> # v5.2
Fixes: a0ac778eb8 ("mtd: rawnand: ingenic: Add support for the JZ4740")
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211016132228.40254-3-paul@crapouillou.net
The function nand_davinci_read_page_hwecc_oob_first() first reads the
OOB data, extracts the ECC information, programs the ECC hardware before
reading the actual data in a loop.
Right after the OOB data was read, it called nand_read_page_op() to
reset the read cursor to the beginning of the page. This caused the
first page to be read twice: in that call, and later in the loop.
Address that issue by changing the call to nand_read_page_op() to
nand_change_read_column_op(), which will only reset the read cursor.
Cc: <stable@vger.kernel.org> # v5.2
Fixes: a0ac778eb8 ("mtd: rawnand: ingenic: Add support for the JZ4740")
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211016132228.40254-2-paul@crapouillou.net
The function nand_davinci_read_page_hwecc_oob_first() does read the ECC
data from the OOB area. Therefore it does not need to calculate the ECC
as it is already available.
Cc: <stable@vger.kernel.org> # v5.2
Fixes: a0ac778eb8 ("mtd: rawnand: ingenic: Add support for the JZ4740")
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211016132228.40254-1-paul@crapouillou.net
The Power Fault Detected bit in the Slot Status register differs from
all other hotplug events in that it is sticky: It can only be cleared
after turning off slot power. Per PCIe r5.0, sec. 6.7.1.8:
If a power controller detects a main power fault on the hot-plug slot,
it must automatically set its internal main power fault latch [...].
The main power fault latch is cleared when software turns off power to
the hot-plug slot.
The stickiness used to cause interrupt storms and infinite loops which
were fixed in 2009 by commits 5651c48cfa ("PCI pciehp: fix power fault
interrupt storm problem") and 99f0169c17 ("PCI: pciehp: enable
software notification on empty slots").
Unfortunately in 2020 the infinite loop issue was inadvertently
reintroduced by commit 8edf5332c3 ("PCI: pciehp: Fix MSI interrupt
race"): The hardirq handler pciehp_isr() clears the PFD bit until
pciehp's power_fault_detected flag is set. That happens in the IRQ
thread pciehp_ist(), which never learns of the event because the hardirq
handler is stuck in an infinite loop. Fix by setting the
power_fault_detected flag already in the hardirq handler.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=214989
Link: https://lore.kernel.org/linux-pci/DM8PR11MB5702255A6A92F735D90A4446868B9@DM8PR11MB5702.namprd11.prod.outlook.com
Fixes: 8edf5332c3 ("PCI: pciehp: Fix MSI interrupt race")
Link: https://lore.kernel.org/r/66eaeef31d4997ceea357ad93259f290ededecfd.1637187226.git.lukas@wunner.de
Reported-by: Joseph Bao <joseph.bao@intel.com>
Tested-by: Joseph Bao <joseph.bao@intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org # v4.19+
Cc: Stuart Hayes <stuart.w.hayes@gmail.com>
Remove useless __init atrribute and unneeded extern qualifier in function
declarations in header files.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20211015151425.29743-1-s.nawrocki@samsung.com
__clk_lookup() interface is obsolete, so remove it from the Samsung clock
drivers. This has been achieved by getting rid of custom _get_rate()
helper and replacing it with clk_hw_get_rate().
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Link: https://lore.kernel.org/r/20211018125456.8292-2-m.szyprowski@samsung.com
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Advertise support of the Gen4 automotive variants in module's device ID
table and add the same IDs to the list of switchtec quirks.
Link: https://lore.kernel.org/r/20211119003803.2333-2-kelvin.cao@microchip.com
Signed-off-by: Kelvin Cao <kelvin.cao@microchip.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Each member of Array[][] should be initialized on a separate line.
Link: https://lore.kernel.org/r/20211119140208.40416-7-liangwenpeng@huawei.com
Signed-off-by: Xinhao Liu <liuxinhao@huawei.com>
Signed-off-by: Wenpeng Liang <liangwenpeng@huawei.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
The type of the variable participating in the shift operation should be an
unsigned type instead of a signed type.
Link: https://lore.kernel.org/r/20211119140208.40416-5-liangwenpeng@huawei.com
Signed-off-by: Xinhao Liu <liuxinhao5@hisilicon.com>
Signed-off-by: Wenpeng Liang <liangwenpeng@huawei.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
There should be a space between the code and the comment on the right.
Link: https://lore.kernel.org/r/20211119140208.40416-4-liangwenpeng@huawei.com
Signed-off-by: Xinhao Liu <liuxinhao5@hisilicon.com>
Signed-off-by: Wenpeng Liang <liangwenpeng@huawei.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
The print format should be consistent with the variable type.
Link: https://lore.kernel.org/r/20211119140208.40416-3-liangwenpeng@huawei.com
Signed-off-by: Xinhao Liu <liuxinhao5@hisilicon.com>
Signed-off-by: Wenpeng Liang <liangwenpeng@huawei.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
The hex printf format should be "0xff" instead of "ff".
Link: https://lore.kernel.org/r/20211119140208.40416-2-liangwenpeng@huawei.com
Signed-off-by: Xinhao Liu <liuxinhao5@hisilicon.com>
Signed-off-by: Wenpeng Liang <liangwenpeng@huawei.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
RXE_POOL_ALIGN is only used in rxe_pool.c so move RXE_POOL_ALIGN to
rxe_pool.c from rxe_pool.h. RXE_POOL_CACHE_FLAGS is never used so it is
deleted from rxe_pool.h
Link: https://lore.kernel.org/r/20211103050241.61293-8-rpearsonhpe@gmail.com
Signed-off-by: Bob Pearson <rpearsonhpe@gmail.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
This allows us to finally get rid of all the assumptions that vma->obj
is NULL.
Changes since v1:
- Ensure the mock_ring vma is pinned to prevent a fault.
- Pin it high to avoid failure in evict_for_vma selftest.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211117142024.1043017-3-matthew.auld@intel.com
We currently have to special case vma->obj being NULL because
of gen6 ppgtt and mock_engine. Fix gen6 ppgtt, so we may soon
be able to remove a few checks. As the object only exists as
a fake object pointing to ggtt, we have no backing storage,
so no real object is created. It just has to look real enough.
Also kill pin_mutex, it's not compatible with ww locking,
and we can use the vm lock instead.
v2:
- Drop IS_SHRINKABLE and shorten overly long line
v3:
- Checkpatch fix for alignment
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211117142024.1043017-2-matthew.auld@intel.com
In intel_context_do_pin_ww, when calling into the pre_pin hook(which is
passed the ww context) it could in theory return -EDEADLK(which is very
likely with debug kernels), once we start adding more ww locking in there,
like in the next patch. If so then we need to be mindful of having to
restart the do_pin at this point.
If this is the kernel_context, or some other early in-kernel context
where we have yet to setup the default_state, then we always inhibit the
context restore, and instead rely on the delayed active_release to set
the CONTEXT_VALID_BIT for us(if we even care), which should indicate
that we have context switched away, and that our newly saved context
state should now be valid. However, since we currently grab the active
reference before the potential ww dance, we can end up setting the
CONTEXT_VALID_BIT much too early, if we need to backoff, and then upon
re-trying the do_pin, we could potentially cause the hardware to
incorrectly load some garbage context state when later context switching
to that context, but at the very least this will trigger the
GEM_BUG_ON() in __engine_unpark. For now let's just move any ww dance
stuff prior to arming the active reference.
For normal user contexts this shouldn't be a concern, since we should
already have the default_state ready when initialising the lrc state,
and so there should be no concern with active_release somehow
prematurely setting the CONTEXT_VALID_BIT.
v2(Thomas):
- Also re-order the onion unwind
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Cc: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211117142024.1043017-1-matthew.auld@intel.com
In rxe_pool.c currently there are many cases where it is necessary to
compute the offset from a pool element struct to the object containing it
in a type independent way where the offset is different for each type. By
saving a pointer to the object when they are created extra work can be
saved.
Link: https://lore.kernel.org/r/20211103050241.61293-5-rpearsonhpe@gmail.com
Signed-off-by: Bob Pearson <rpearsonhpe@gmail.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
In rxe_pool.c copy remaining pool setup parameters from rxe_pool_info into
rxe_pool. This saves looking up rxe_pool_info in the performance path.
Link: https://lore.kernel.org/r/20211103050241.61293-4-rpearsonhpe@gmail.com
Signed-off-by: Bob Pearson <rpearsonhpe@gmail.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Currently three different names are used to describe rxe pool elements.
They are referred to as entries, elems or pelems. This patch chooses one
'elem' and changes the other ones.
Link: https://lore.kernel.org/r/20211103050241.61293-3-rpearsonhpe@gmail.com
Signed-off-by: Bob Pearson <rpearsonhpe@gmail.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Most of the locks in the rxe driver are _irqsave/restore locks but in fact
there are no interrupt threads that run rxe code or share data with
rxe. There are softirq threads and data sharing so the appropriate lock
type is _bh. This patch replaces all irqsave type locks with bh type
locks.
Link: https://lore.kernel.org/r/20211103050241.61293-2-rpearsonhpe@gmail.com
Signed-off-by: Bob Pearson <rpearsonhpe@gmail.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
When a VF goes through a reset, it's possible for the VF's feature set
to change. For example it may lose the VIRTCHNL_VF_OFFLOAD_VLAN
capability after VF reset. Unfortunately, the driver doesn't correctly
deal with this situation and errors are seen from downing/upping the
interface and/or moving the interface in/out of a network namespace.
When setting the interface down/up we see the following errors after the
VIRTCHNL_VF_OFFLOAD_VLAN capability was taken away from the VF:
ice 0000:51:00.1: VF 1 failed opcode 12, retval: -64 iavf 0000:51:09.1:
Failed to add VLAN filter, error IAVF_NOT_SUPPORTED ice 0000:51:00.1: VF
1 failed opcode 13, retval: -64 iavf 0000:51:09.1: Failed to delete VLAN
filter, error IAVF_NOT_SUPPORTED
These add/delete errors are happening because the VLAN filters are
tracked internally to the driver and regardless of the VLAN_ALLOWED()
setting the driver tries to delete/re-add them over virtchnl.
Fix the delete failure by making sure to delete any VLAN filter tracking
in the driver when a removal request is made, while preventing the
virtchnl request. This makes it so the driver's VLAN list is up to date
and the errors are
Fix the add failure by making sure the check for VLAN_ALLOWED() during
reset is done after the VF receives its capability list from the PF via
VIRTCHNL_OP_GET_VF_RESOURCES. If VLAN functionality is not allowed, then
prevent requesting re-adding the filters over virtchnl.
When moving the interface into a network namespace we see the following
errors after the VIRTCHNL_VF_OFFLOAD_VLAN capability was taken away from
the VF:
iavf 0000:51:09.1 enp81s0f1v1: NIC Link is Up Speed is 25 Gbps Full Duplex
iavf 0000:51:09.1 temp_27: renamed from enp81s0f1v1
iavf 0000:51:09.1 mgmt: renamed from temp_27
iavf 0000:51:09.1 dev27: set_features() failed (-22); wanted 0x020190001fd54833, left 0x020190001fd54bb3
These errors are happening because we aren't correctly updating the
netdev capabilities and dealing with ndo_fix_features() and
ndo_set_features() correctly.
Fix this by only reporting errors in the driver's ndo_set_features()
callback when VIRTCHNL_VF_OFFLOAD_VLAN is not allowed and any attempt to
enable the VLAN features is made. Also, make sure to disable VLAN
insertion, filtering, and stripping since the VIRTCHNL_VF_OFFLOAD_VLAN
flag applies to all of them and not just VLAN stripping.
Also, after we process the capabilities in the VF reset path, make sure
to call netdev_update_features() in case the capabilities have changed
in order to update the netdev's feature set to match the VF's actual
capabilities.
Lastly, make sure to always report success on VLAN filter delete when
VIRTCHNL_VF_OFFLOAD_VLAN is not supported. The changed flow in
iavf_del_vlans() allows the stack to delete previosly existing VLAN
filters even if VLAN filtering is not allowed. This makes it so the VLAN
filter list is up to date.
Fixes: 8774370d26 ("i40e/i40evf: support for VF VLAN tag stripping control")
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently iavf adapter statistics are refreshed only in a
watchdog task, triggered approximately every two seconds,
which causes some ethtool requests to return outdated values.
Add explicit statistics refresh when requested by ethtool -S.
Fixes: b476b0030e ("iavf: Move commands processing to the separate function")
Signed-off-by: Jan Sokolowski <jan.sokolowski@intel.com>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
System hangs if close the interface is called from the kernel during
the interface is in resetting state.
During resetting operation the link is closing but kernel didn't
know it and it tried to close this interface again what sometimes
led to deadlock.
Inform kernel about current state of interface
and turn off the flag IFF_UP when interface is closing until reset
is finished.
Previously it was most likely to hang the system when kernel
(network manager) tried to close the interface in the same time
when interface was in resetting state because of deadlock.
Fixes: 3c8e0b989a ("i40vf: don't stop me now")
Signed-off-by: Jaroslaw Gawin <jaroslawx.gawin@intel.com>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The pointer 'mem' was initialized to 'fw->data' but immediately after
that it was assigned 'fw->data + 10'. Lets remove the extra assignement
and initialize the pointer to the address its going to use.
Link: https://lore.kernel.org/linux-media/20210416235336.1552102-1-sudipm.mukherjee@gmail.com
Cc: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
At connection time (or boot) in si2168_probe(), the firmware is not
loaded to the device and the device is not fully activated. It is
not useful or sensible to do this full initialization on resume in
case it has not been previously initialized and is expected to be
in this initialized state.
Calling si2168_init() and therefore reading the firmware file for
the first time during resume leads to problems and should be avoided.
It is however safe to read the firmware file once it has already been
read outside of a suspend/resume situation.
Add a staus flag 'initialized' to store whether si2168_init() has
successfully been called. If initialization fails (e.g. due to missing
firmware file), the flag is not set.
Register a separate si2168_resume callback which only calls
si2168_init() once the 'initialized' flag has been set and it is safe
to load the firmware at resume.
The first call to si2168_init() will now always happen when the device
is actually used for the first time and never during resume.
This avoids the unsafe firmware file reading and should also speed up
resume by skipping unnecessary device initialization.
Link: https://lore.kernel.org/linux-media/20210418001204.7453-3-kernel@tuxforce.de
[mchehab: fix several Coding Style issues]
Cc: Antti Palosaari <crope@iki.fi>
Signed-off-by: Lukas Middendorf <kernel@tuxforce.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The si2168 B40 firmware file name has been changed in or before 2014.
During initialization, the new file name is preferred, but the old file
name is used as a fallback when request_firmware with the new file name
fails. Once reading the old file name has been attempted, only this name
will be used on further firmware loading attempts. During resume,
firmware reading with the new file name can (and likely will) fail even
when it actually exists. So this permanent switch to the fallback
firmware name happens even when not desired.
Any system using a recent kernel version can be expected to have the
firmware under the new name. The major distributions are either using
the dvb firmware collection from LibreELEC, which has the new firmware
file name, or do not package the firmware file but have documentation
pointing towards a manual installation of the firmware file under the
new name. If the firmware is available under the old name, it is
severely outdated. If the switch to the old file name is performed,
further firmware loading will either permanently fail (if it is not
available) or an outdated firmware version will be used.
Drop support for the fallback firmware file name and fail directly if
the firmware is not available under its current name. On following
attempts, the firmware read will then be retried with the correct
current name instead of the old name.
As reasoned above, there should be no negative effects of this change,
while simplifying code (the B40 variant will be handled identical
compared to the other variants of the si2168) and at the same time
fixing possible problems if firmware loading fails on resume.
Link: https://lore.kernel.org/linux-media/20210418161544.58858-1-kernel@tuxforce.de
Signed-off-by: Lukas Middendorf <kernel@tuxforce.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Resolve being able to change static values on VF when adaptive interrupt
moderation is enabled.
This problem is fixed by checking the interrupt settings is not
a combination of change of static value while adaptive interrupt
moderation is turned on.
Without this fix, the user would be able to change static values
on VF with adaptive moderation enabled.
Fixes: 65e87c0398 ("i40evf: support queue-specific settings for interrupt moderation")
Signed-off-by: Nitesh B Venkatesh <nitesh.b.venkatesh@intel.com>
Tested-by: George Kuruvinakunnel <george.kuruvinakunnel@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
This fixes a problem where closing the tuner would leave it in a state
where it would not tune to any channel when reopened. This problem was
discovered as part of https://github.com/hselasky/webcamd/issues/16.
Since adap->id is 0 or 1, this bit-shift overflows, which is undefined
behavior. The driver still worked in practice as the overflow would in
most environments result in 0, which rendered the line a no-op. When
running the driver as part of webcamd however, the overflow could lead
to 0xff due to optimizations by the compiler, which would, in the end,
improperly shut down the tuner.
The bug is a regression introduced in the commit referenced below. The
present patch causes identical behavior to before that commit for
adap->id equal to 0 or 1. The driver does not contain support for
dib0700 devices with more adapters, assuming such even exist.
Tests have been performed with the Xbox One Digital TV Tuner on amd64.
Not all dib0700 devices are expected to be affected by the regression;
this code path is only taken by those with incorrect endpoint numbers.
Link: https://lore.kernel.org/linux-media/1d2fc36d94ced6f67c7cc21dcc469d5e5bdd8201.1632689033.git.mchehab+huawei@kernel.org
Cc: stable@vger.kernel.org
Fixes: 7757ddda6f ("[media] DiB0700: add function to change I2C-speed")
Signed-off-by: Michael Kuron <michael.kuron@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This looks like a typo. By manipulating the antenna on a device while
monitoring the reported SNR, I was able to see the unexpected jump.
After applying this patch, the spike was no longer present.
Link: https://lore.kernel.org/linux-media/20211003001805.735092-1-logans@cottsay.net
Signed-off-by: Scott K Logan <logans@cottsay.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Remove the unnecessary "umem_pd" variable. And usnic_uiom_alloc_pd()
never returns NULL so remove the NULL check.
Link: https://lore.kernel.org/r/20211118113924.GH1147@kili
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Add an artificial minimal example simulating compilers producing two
different types within a single CU that correspond to identical struct
definitions.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20211117194114.347675-2-andrii@kernel.org
According to [0], compilers sometimes might produce duplicate DWARF
definitions for exactly the same struct/union within the same
compilation unit (CU). We've had similar issues with identical arrays
and handled them with a similar workaround in 6b6e6b1d09 ("libbpf:
Accomodate DWARF/compiler bug with duplicated identical arrays"). Do the
same for struct/union by ensuring that two structs/unions are exactly
the same, down to the integer values of field referenced type IDs.
Solving this more generically (allowing referenced types to be
equivalent, but using different type IDs, all within a single CU)
requires a huge complexity increase to handle many-to-many mappings
between canonidal and candidate type graphs. Before we invest in that,
let's see if this approach handles all the instances of this issue in
practice. Thankfully it's pretty rare, it seems.
[0] https://lore.kernel.org/bpf/YXr2NFlJTAhHdZqq@krava/
Reported-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20211117194114.347675-1-andrii@kernel.org
While dvb_tuner_ops already has dedicated suspend and resume callbacks,
dvb_frontend_ops currently does not have them. Add those callbacks and
use them for suspend and resume. If they are not set, the old behavior
of calling sleep or init is used.
This allows dvb_frontend drivers to handle resume differently from init,
and suspend differently from sleep. No change is required for drivers
not needing this functionality.
Link: https://lore.kernel.org/linux-media/20210418001204.7453-2-kernel@tuxforce.de
Cc: Lukas Middendorf <kernel@tuxforce.de>, Antti Palosaari <crope@iki.fi>, Mauro Carvalho Chehab <mchehab@kernel.org>, Luis Chamberlain <mcgrof@kernel.org>
Signed-off-by: Lukas Middendorf <kernel@tuxforce.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Use the addrconf_addr_eui48() helper function to set the GUIDs, Also make
sure the GUIDs are valid EUI-64 identifiers.
Link: https://lore.kernel.org/r/20211118100456.45423-1-kamalheib1@gmail.com
Signed-off-by: Kamal Heib <kamalheib1@gmail.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
