Updated invoke to use new common TA structure similarily to load/unload.
Signed-off-by: Candice Li <candice.li@amd.com>
Reviewed-by: John Clements <john.clements@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
ASSR is dependent on Signed PSP Verstage to enable Content
Protection for eDP panels. Unsigned PSP verstage is used
during development phase causing ASSR to FAIL.
As a result, link training is performed with
DP_PANEL_MODE_DEFAULT instead of DP_PANEL_MODE_EDP for
eDP panels that causes display flicker on some panels.
[How]
- Do not change panel mode, if ASSR is disabled
- Just report and continue to perform eDP link training
with right settings further.
Signed-off-by: Praful Swarnakar <Praful.Swarnakar@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
gmc_v{9,10}_0_gart_disable() isn't called matched with
correspoding gart_enbale function in SRIOV case. This will
lead to gart.bo pin_count leak on driver unload.
Cc: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Leslie Shi <Yuliang.Shi@amd.com>
Signed-off-by: Guchun Chen <guchun.chen@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
WCN6855 has 2 phys, one is 2G, another is 5G/6G, so it should copy the
cap info of 6G band under the check of WMI_HOST_WLAN_5G_CAP as well as
for the 5G band. Some chips like QCN9074 only have 6G, not have 2G and
5G, and this 6G capability is also under WMI_HOST_WLAN_5G_CAP, so this
change will not disturb it.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210804181217.88751-4-jouni@codeaurora.org
For some chips such as WCN6855, single_pdev_only is set in struct
ath11k_hw_params which means ath11k calls ieee80211_register_hw() only
once and create only one device interface, and that device interface
supports all 2G/5G/6G channels.
ath11k_mac_setup_channels_rates() sets up the channels and it is called
for each device interface. It is called only once for single_pdev_only,
and then set up all channels for 2G/5G/6G. The logic of
ath11k_mac_setup_channels_rates() is not suitable for single_pdev_only,
it leads to all 6G channels being disabled for the device interface
which is single_pdev_only such as WCN6855.
Add channel frequency checks for the 6G band and enable the 6G channels
properly based on what is supported by the chip.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210804181217.88751-3-jouni@codeaurora.org
WCN6855 uses single_pdev_only, so it supports both the 5G and 6G bands
in the same ath11k/pdev and it needs to enable ht_cap/vht_cap for the 5G
band, otherwise it will downgrade to non-HT mode for the 5G band. Some
chips like QCN9074 only support the 6G band, not the 5G band, and use
the flag ar->supports_6ghz which is true to discard ht_cap/vht_cap.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210804181217.88751-2-jouni@codeaurora.org
When ath11k receives survey request, choose the 6 GHz band when enabled.
Without this, survey request does not include any 6 GHz band results,
thereby causing auto channel selection to fail.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1-01386-QCAHKSWPL_SILICONZ-1
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210722102054.43419-3-jouni@codeaurora.org
Frequency in rx status is being filled incorrectly in the 6 GHz band as
channel number received is invalid in this case which is causing packet
drops. So fix that.
Fixes: 5dcf42f8b7 ("ath11k: Use freq instead of channel number in rx path")
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210722102054.43419-2-jouni@codeaurora.org
Add support for the 6 GHz channel 2 with center frequency 5935 MHz and
operating class 136 per IEEE Std 802.11ax-2021, Table E-4.
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210722102054.43419-1-jouni@codeaurora.org
Current driver uses software CQ head pointer to poll on CQE
header in memory to determine if CQE is valid. Software needs
to make sure, that the reads of the CQE do not get re-ordered
so much that it ends up with an inconsistent view of the CQE.
To ensure that DMB barrier after read to first CQE cacheline
and before reading of the rest of the CQE is needed.
But having barrier for every CQE read will impact the performance,
instead use hardware CQ head and tail pointers to find the
valid number of CQEs.
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf 2021-09-28
The following pull-request contains BPF updates for your *net* tree.
We've added 10 non-merge commits during the last 14 day(s) which contain
a total of 11 files changed, 139 insertions(+), 53 deletions(-).
The main changes are:
1) Fix MIPS JIT jump code emission for too large offsets, from Piotr Krysiuk.
2) Fix x86 JIT atomic/fetch emission when dst reg maps to rax, from Johan Almbladh.
3) Fix cgroup_sk_alloc corner case when called from interrupt, from Daniel Borkmann.
4) Fix segfault in libbpf's linker for objects without BTF, from Kumar Kartikeya Dwivedi.
5) Fix bpf_jit_charge_modmem for applications with CAP_BPF, from Lorenz Bauer.
6) Fix return value handling for struct_ops BPF programs, from Hou Tao.
7) Various fixes to BPF selftests, from Jiri Benc.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
,
Hariprasad Kelam says:
====================
Externel ptp clock support
Externel ptp support is required in a scenario like connecting
a external timing device to the chip for time synchronization.
This series of patches adds support to ptp driver to use external
clock and enables PTP config in CN10K MAC block (RPM). Currently
PTP configuration is left unchanged in FLR handler these patches
addresses the same.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
,
PTP hardware block can be configured to utilize
the external clock. Also the current ptp timestamp
can be captured when external trigger is applied on
a gpio pin. These features are required in scenarios
like connecting a external timing device to the chip
for time synchronization. The timing device provides
the clock and trigger(PPS signal) to the PTP block.
This patch does the following:
1. configures PTP block to use external clock
frequency and timestamp capture on external event.
2. sends PTP_REQ_EXTTS events to kernel ptp phc susbsytem
with captured timestamps
3. aligns PPS edge to adjusted ptp clock in the ptp device
by setting the PPS_THRESH to the reminder of the last
timestamp value captured by external PPS
Signed-off-by: Yi Guo <yig@marvell.com>
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The input clock frequency of PTP block is figured
out from hardware reset block currently. The firmware
data already has this info in sclk. Hence simplify
ptp driver to use sclk from firmware data.
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MAC on CN10K support hardware timestamping such that 8 bytes addition
header is prepended to incoming packets. This patch does necessary
configuration to enable Hardware time stamping upon receiving request
from PF netdev interfaces.
Timestamp configuration is different on MAC (CGX) Octeontx2 silicon
and MAC (RPM) OcteonTX3 CN10k. Based on silicon variant appropriate
fn() pointer is called. Refactor MAC specific mbox messages to remove
unnecessary gaps in mboxids.
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Upon receiving ptp config request from netdev interface , Octeontx2 MAC
block CGX is configured to append timestamp to every incoming packet
and NPC config is updated with DMAC offset change.
Currently this configuration is not reset in FLR handler. This patch
resets the same.
Signed-off-by: Harman Kalra <hkalra@marvell.com>
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 2d52c58b9c.
We have had several folks complain that this causes hangs for them, which
is especially problematic as the commit has also hit stable already.
As no resolution seems to be forthcoming right now, revert the patch.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=214503
Fixes: 2d52c58b9c ("block, bfq: honor already-setup queue merges")
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This function copies strings around between multiple buffers
including a large on-stack array that causes a build warning
on 32-bit systems:
drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_debugfs.c: In function 'hclge_dbg_dump_tm_pg':
drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_debugfs.c:782:1: error: the frame size of 1424 bytes is larger than 1400 bytes [-Werror=frame-larger-than=]
The function can probably be cleaned up a lot, to go back to
printing directly into the output buffer, but dynamically allocating
the structure is a simpler workaround for now.
Fixes: 04d96139dd ("net: hns3: refine function hclge_dbg_dump_tm_pri()")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the documentation the second resource is optional. But the
blamed commit ignores that and if the resource is not there it just
fails.
This patch reverts that to still allow the second resource to be
optional because other SoC have the some MDIO controller and doesn't
need to second resource.
Fixes: 672a1c3949 ("net: mdio: mscc-miim: Make use of the helper function devm_platform_ioremap_resource()")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IV of CCM mode has special requirements, this patch supports CCM
mode of SM4 algorithm.
Signed-off-by: Tianjia Zhang <tianjia.zhang@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
unix_create1() returns NULL on error, and the callers assume that it never
fails for reasons other than out of memory. So, the callers always return
-ENOMEM when unix_create1() fails.
However, it also returns NULL when the number of af_unix sockets exceeds
twice the limit controlled by sysctl: fs.file-max. In this case, the
callers should return -ENFILE like alloc_empty_file().
This patch changes unix_create1() to return the correct error value instead
of NULL on error.
Out of curiosity, the assumption has been wrong since 1999 due to this
change introduced in 2.2.4 [0].
diff -u --recursive --new-file v2.2.3/linux/net/unix/af_unix.c linux/net/unix/af_unix.c
--- v2.2.3/linux/net/unix/af_unix.c Tue Jan 19 11:32:53 1999
+++ linux/net/unix/af_unix.c Sun Mar 21 07:22:00 1999
@@ -388,6 +413,9 @@
{
struct sock *sk;
+ if (atomic_read(&unix_nr_socks) >= 2*max_files)
+ return NULL;
+
MOD_INC_USE_COUNT;
sk = sk_alloc(PF_UNIX, GFP_KERNEL, 1);
if (!sk) {
[0]: https://cdn.kernel.org/pub/linux/kernel/v2.2/patch-2.2.4.gz
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Configure multiple BSSID and enhanced multi-BSSID advertisement (EMA)
parameters in mac80211 for AP mode.
For each interface, 'mbssid_tx_vif' points to the transmitting interface of
the MBSSID set. The pointer is set to NULL if MBSSID is disabled.
Function ieee80211_stop() is modified to always bring down all the
non-transmitting interfaces first and the transmitting interface last.
Signed-off-by: John Crispin <john@phrozen.org>
Co-developed-by: Aloka Dixit <alokad@codeaurora.org>
Signed-off-by: Aloka Dixit <alokad@codeaurora.org>
Link: https://lore.kernel.org/r/20210916025437.29138-3-alokad@codeaurora.org
[slightly change logic to be more obvious]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
up->corkflag field can be read or written without any lock.
Annotate accesses to avoid possible syzbot/KCSAN reports.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When CONFIG_INET is not set, there are failing references to IPv4
functions, so make this driver depend on INET.
Fixes these build errors:
sparc64-linux-ld: drivers/net/ethernet/sun/sunvnet_common.o: in function `sunvnet_start_xmit_common':
sunvnet_common.c:(.text+0x1a68): undefined reference to `__icmp_send'
sparc64-linux-ld: drivers/net/ethernet/sun/sunvnet_common.o: in function `sunvnet_poll_common':
sunvnet_common.c:(.text+0x358c): undefined reference to `ip_send_check'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Aaron Young <aaron.young@oracle.com>
Cc: Rashmi Narasimhan <rashmi.narasimhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't print stats for which we haven't reserved space as it can
cause nasty memory bashing and related bad behaviors.
Fixes: aa620993b1 ("ionic: pull per-q stats work out of queue loops")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
nguy/net-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2021-09-27
This series contains updates to e100 driver only.
Jake corrects under allocation of register buffer due to incorrect
calculations and fixes buffer overrun of register dump.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
To follow 20-character length limitation of platform device name, we
have only 7 character space for amplifier. Therefore, the last
character of mx98357a and mx98360a is removed to save space.
Signed-off-by: Brent Lu <brent.lu@intel.com>
Fixes: e224ef76fa ('ASoC: intel: sof_rt5682: support jsl_rt5682s_mx98360a board')
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210927143249.439129-1-brent.lu@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
If we get an error on reply (msg->reply_error) then we should print the
error value out.
At the same time extend the print to include the message size as well and
do the same in case of a timeout.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Daniel Baluta <daniel.baluta@gmail.com>
Reviewed-by: Paul Olaru <paul.olaru@oss.nxp.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210928073615.29574-1-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
These helped troubleshoot some DMA issue in SOF.
Signed-off-by: Marc Herbert <marc.herbert@intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20210928102635.26227-1-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
If an invalid stream is passed to snd_sof_ipc_msg_data() it won't
fill the provided object with data. The caller has to be able to
recognise such cases to avoid handling invalid data. Make the
function return an error when failing.
Signed-off-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20210928103516.8066-1-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Sparse (make C=2) complains about undeclared variables. Fix by adding
a real prototype instead of 'extern' in sof-of-dev.c
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Daniel Baluta <daniel.baluta@gmail.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Paul Olaru <paul.olaru@oss.nxp.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20210928072807.27838-1-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There is no restore_stream flag anymmore.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Paul Olaru <paul.olaru@oss.nxp.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Bard Liao <bard.liao@intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20210928074030.30553-1-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In order to provide more information in case of timeout observed while
reading STREAM_SD_OFFSET, print out the stream name or in case there is
no audio stream associated (like dma-trace), print "--"
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/20210928081744.4785-1-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Kbuild supports <modname>-y as well as <modname>-objs.
This simplifies the Makefile.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Assign the objects directly to obj-$(CONFIG_INET).
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many architectures don't define virt_to_bus() any more, as drivers
should be using the dma-mapping interfaces where possible:
In file included from drivers/net/hamradio/dmascc.c:27:
drivers/net/hamradio/dmascc.c: In function 'tx_on':
drivers/net/hamradio/dmascc.c:976:30: error: implicit declaration of function 'virt_to_bus'; did you mean 'virt_to_fix'? [-Werror=implicit-function-declaration]
976 | virt_to_bus(priv->tx_buf[priv->tx_tail]) + n);
| ^~~~~~~~~~~
arch/arm/include/asm/dma.h:109:52: note: in definition of macro 'set_dma_addr'
109 | __set_dma_addr(chan, (void *)__bus_to_virt(addr))
| ^~~~
Add the Kconfig dependency to prevent this from being built on
architectures without virt_to_bus().
Fixes: bc1abb9e55 ("dmascc: use proper 'virt_to_bus()' rather than casting to 'int'")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
An object file cannot be built for both loadable module and built-in
use at the same time:
arm-linux-gnueabi-ld: drivers/net/ethernet/micrel/ks8851_common.o: in function `ks8851_probe_common':
ks8851_common.c:(.text+0xf80): undefined reference to `__this_module'
Change the ks8851_common code to be a standalone module instead,
and use Makefile logic to ensure this is built-in if at least one
of its two users is.
Fixes: 797047f875 ("net: ks8851: Implement Parallel bus operations")
Link: https://lore.kernel.org/netdev/20210125121937.3900988-1-arnd@kernel.org/
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
My previous patch had an off-by-one error in the added sanity
check, the arrays are MTL_MAX_{RX,TX}_QUEUES long, so if that
index is that number, it has overflown.
The patch silenced the warning anyway because the strings could
no longer overlap with the input, but they could still overlap
with other fields.
Fixes: 3e0d5699a9 ("net: stmmac: fix gcc-10 -Wrestrict warning")
Reported-by: Russell King (Oracle) <linux@armlinux.org.uk>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
clang warns about arithmetic on NULL pointers:
drivers/net/ethernet/ti/am65-cpsw-ethtool.c:71:2: error: performing pointer subtraction with a null pointer has undefined behavior [-Werror,-Wnull-pointer-subtraction]
AM65_CPSW_REGDUMP_REC(AM65_CPSW_REGDUMP_MOD_NUSS, 0x0, 0x1c),
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/ti/am65-cpsw-ethtool.c:64:29: note: expanded from macro 'AM65_CPSW_REGDUMP_REC'
.hdr.len = (((u32 *)(end)) - ((u32 *)(start)) + 1) * sizeof(u32) * 2 + \
^ ~~~~~~~~~~~~~~~~
The expression here is easily changed to a calculation based on integers
that is no less readable.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
When rhashtable_init() fails, it returns -EINVAL.
However, since error return value of rhashtable_init is not checked,
it can cause use of uninitialized pointers.
So, fix unhandled errors of rhashtable_init.
Signed-off-by: MichelleJin <shjy180909@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When rhashtable_init() fails, it returns -EINVAL.
However, since error return value of rhashtable_init is not checked,
it can cause use of uninitialized pointers.
So, fix unhandled errors of rhashtable_init.
Signed-off-by: MichelleJin <shjy180909@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When rhashtable_init() fails, it returns -EINVAL.
However, since error return value of rhashtable_init is not checked,
it can cause use of uninitialized pointers.
So, fix unhandled errors of rhashtable_init.
Signed-off-by: MichelleJin <shjy180909@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables Realtek 8822C and 8852A to support the AOSP
extension.
Reviewed-by: Miao-chen Chou <mcchou@chromium.org>
Signed-off-by: Joseph Hwang <josephsih@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch enables Qualcomm WCN399x to support the AOSP extension.
Reviewed-by: Miao-chen Chou <mcchou@chromium.org>
Signed-off-by: Joseph Hwang <josephsih@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Deactivate old rule first, then append the new rule, so rule replacement
notification via netlink first reports the deletion of the old rule with
handle X in first place, then it adds the new rule (reusing the handle X
of the replaced old rule).
Note that the abort path releases the transaction that has been created
by nft_delrule() on error.
Fixes: ca08987885 ("netfilter: nf_tables: deactivate expressions in rule replecement routine")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Add position handle to allow to identify the rule location from netlink
events. Otherwise, userspace cannot incrementally update a userspace
cache through monitoring events.
Skip handle dump if the rule has been either inserted (at the beginning
of the ruleset) or appended (at the end of the ruleset), the
NLM_F_APPEND netlink flag is sufficient in these two cases.
Handle NLM_F_REPLACE as NLM_F_APPEND since the rule replacement
expansion appends it after the specified rule handle.
Fixes: 96518518cc ("netfilter: add nftables")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This is a revert of
7b1957b049 ("netfilter: nf_defrag_ipv4: use net_generic infra")
and a partial revert of
8b0adbe3e3 ("netfilter: nf_defrag_ipv6: use net_generic infra").
If conntrack is builtin and kernel is booted with:
nf_conntrack.enable_hooks=1
.... kernel will fail to boot due to a NULL deref in
nf_defrag_ipv4_enable(): Its called before the ipv4 defrag initcall is
made, so net_generic() returns NULL.
To resolve this, move the user refcount back to struct net so calls
to those functions are possible even before their initcalls have run.
Fixes: 7b1957b049 ("netfilter: nf_defrag_ipv4: use net_generic infra")
Fixes: 8b0adbe3e3 ("netfilter: nf_defrag_ipv6: use net_generic infra").
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>