When the driver sends a peer create cmd, the firmware responds with
WMI_PEER_CREATE_CONF_EVENTID to confirm the firmware received
WMI_PEER_CREATE_CMDID. Since the peer create conf event is not handled
in ath11k_wmi_tlv_op_rx, we are getting unknown event id warning prints
during peer creation.
Add WMI_PEER_CREATE_CONF_EVENTID in wmi_tlv_event_id and handle
the same as unsupported event id under wmi logs.
warning prints:
[ 4382.230817] ath11k_pci 0000:01:00.0: Unknown eventid: 0x601a
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01695-QCAHKSWPL_SILICONZ-1
Signed-off-by: P Praneesh <ppranees@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210721212029.142388-9-jouni@codeaurora.org
Facing below warning prints when we do wifi down in multiple VAPs scenario.
warning print:
ath11k c000000.wifi: No VIF found for vdev 2
...
ath11k c000000.wifi: No VIF found for vdev 0
In ath11k_mac_get_arvif_by_vdev_id(), we iterate all the radio to get the
arvif for the requested vdev_id through ath11k_mac_get_arvif().
ath11k_mac_get_arvif() throws a warning message if the given vdev_id is
not found in the given radio. So to avoid the warning message, add
the allocated_vdev_map cross check against the given vdev_id before using
ath11k_mac_get_arvif() to ensure that vdev_id is allocated in the
given radio.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01492-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ6018 hw1.0 AHB WLAN.HK.2.4.0.1-00330-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210721212029.142388-8-jouni@codeaurora.org
In scenario when a peer is disassociating, there could be
multiple places where a reo cmd ring is accessed, such as
during aggregation teardown, tid queue cleanup, etc.
When this happens during firmware recovery where accessing of FW/HW
resources/registers is not recommended, accessing reo cmd ring in
this case could lead to crash or undefined behaviour.
Hence avoid this by checking for corresponding flag to avoid
accessing reo cmd ring during firmware recovery.
Sample crash:
[ 3936.456050] Unhandled fault: imprecise external abort (0x1c06) at 0x54bb842a
[ 3936.456411] WARN: Access Violation!!!, Run "cat /sys/kernel/debug/qcom_debug_logs/tz_log" for more details
[ 3936.467997] pgd = b4474000
[ 3936.477440] [54bb842a] *pgd=6fa61831, *pte=7f95d59f, *ppte=7f95de7e
<snip>
[ 3937.177436] [<8030ab10>] (_raw_spin_unlock_bh) from [<7f5e9eb8>] (ath11k_hal_reo_cmd_send+0x440/0x458 [ath11k])
[ 3937.185730] [<7f5e9eb8>] (ath11k_hal_reo_cmd_send [ath11k]) from [<7f601c4c>] (ath11k_dp_tx_send_reo_cmd+0x2c/0xcc [ath11k])
[ 3937.195524] [<7f601c4c>] (ath11k_dp_tx_send_reo_cmd [ath11k]) from [<7f602f10>] (ath11k_peer_rx_tid_reo_update+0x84/0xbc [ath11k])
[ 3937.206984] [<7f602f10>] (ath11k_peer_rx_tid_reo_update [ath11k]) from [<7f605a9c>] (ath11k_dp_rx_ampdu_stop+0xa8/0x130 [ath11k])
[ 3937.218532] [<7f605a9c>] (ath11k_dp_rx_ampdu_stop [ath11k]) from [<7f5f6730>] (ath11k_mac_op_ampdu_action+0x6c/0x98 [ath11k])
[ 3937.230250] [<7f5f6730>] (ath11k_mac_op_ampdu_action [ath11k]) from [<c7b6e890>] (___ieee80211_stop_rx_ba_session+0x98/0x144 [mac80211])
[ 3937.241499] [<c7b6e890>] (___ieee80211_stop_rx_ba_session [mac80211]) from [<c7b6cdd8>] (ieee80211_sta_tear_down_BA_sessions+0x4c/0xf4 [)
[ 3937.253833] [<c7b6cdd8>] (ieee80211_sta_tear_down_BA_sessions [mac80211]) from [<c7b63460>] (ieee80211_sta_eosp+0x5b8/0x960 [mac80211])
[ 3937.266764] [<c7b63460>] (ieee80211_sta_eosp [mac80211]) from [<c7b66da8>] (__sta_info_flush+0x9c/0x134 [mac80211])
[ 3937.278826] [<c7b66da8>] (__sta_info_flush [mac80211]) from [<c7b7bd00>] (ieee80211_stop_ap+0x14c/0x28c [mac80211])
[ 3937.289240] [<c7b7bd00>] (ieee80211_stop_ap [mac80211]) from [<7f509cf0>] (__cfg80211_stop_ap+0x4c/0xd8 [cfg80211])
[ 3937.299629] [<7f509cf0>] (__cfg80211_stop_ap [cfg80211]) from [<7f4dddec>] (cfg80211_leave+0x24/0x30 [cfg80211])
[ 3937.310041] [<7f4dddec>] (cfg80211_leave [cfg80211]) from [<7f4de03c>] (cfg80211_netdev_notifier_call+0x174/0x48c [cfg80211])
[ 3937.320457] [<7f4de03c>] (cfg80211_netdev_notifier_call [cfg80211]) from [<80339928>] (notifier_call_chain+0x40/0x68)
[ 3937.331636] [<80339928>] (notifier_call_chain) from [<803399a8>] (raw_notifier_call_chain+0x14/0x1c)
[ 3937.342221] [<803399a8>] (raw_notifier_call_chain) from [<8073bb00>] (call_netdevice_notifiers+0xc/0x14)
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01240-QCAHKSWPL_SILICONZ-1
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210721212029.142388-7-jouni@codeaurora.org
Firmware crash is seen randomly, because of sending wrong vdev_id
in vdev_create command. This is due to free_vdev_map value being 0.
free_vdev_map is getting assigned after ieee80211_register_hw. In
some race conditions, add_interface api is getting called before
assigning value to free_vdev_map. Fix this by assigning free_vdev_map
before ieee80211_register_hw.
Also, moved ar->cc_freq_hz and ar->txmgmt_idr initialization before
ieee80211_register_hw to avoid such race conditions.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-00948-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1-01734-QCAHKSWPL_SILICONZ-1
Signed-off-by: Seevalamuthu Mariappan <seevalam@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210721212029.142388-6-jouni@codeaurora.org
Firmware blocks all data traffic until the key is plumbed. But, with
software encryption mode, key is never plumbed to firmware. Due to this,
a traffic failure in software encryption mode has been observed. Hence,
firmware has introduced a flag to differentiate software encryption
mode. This flag can be passed during vdev_start command.
Enable WMI_VDEV_START_HW_ENCRYPTION_DISABLED flag in vdev_start command
to notify firmware to disable hardware encryption for a vdev. This is set
if raw mode software encryption is enabled.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01421-QCAHKSWPL_SILICONZ-1
Signed-off-by: Seevalamuthu Mariappan <seevalam@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210721212029.142388-5-jouni@codeaurora.org
Whenever ath11k is bootup with a user country already set, cfg80211
notifies this country info to ath11k soon after registration, where the
notification is sent to the firmware for fetching the rules of this user
country input.
Multiple race conditions could be seen in this scenario where a new
request is either lost as pointed in [1] or a new regd overwrites the
default regd provided by the firmware during bootup. Note that, the
default regd is used for intersection purpose and hence it should not be
overwritten.
The main reason as pointed by [1] is the usage of ATH11K_FLAG_REGISTERED
flag which is updated after completion of core registration, whereas the
reg notification from cfg80211 and wmi events for the corresponding
request can happen much before that. Since the ATH11K_FLAG_REGISTERED is
currently used to determine if the event containing reg rules belong to
default regd or for user request, there is a possibility of the default
regd getting overwritten.
Since the default reg rules will be received only once per pdev on
firmware load, the above flag based check can be replaced with a check
to see if default_regd is already set, so that we can now always update
the new_regd. Also if the new_regd is set, this will be always used to
update the reg rules for the registered phy.
[1] https://patchwork.kernel.org/project/linux-wireless/patch/1829665.1PRlr7bOQj@ripper/
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01460-QCAHKSWPL_SILICONZ-1
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210721212029.142388-4-jouni@codeaurora.org
During firmware recovery, the default reg rules which are
received via WMI_REG_CHAN_LIST_CC_EVENT can overwrite
the currently configured user regd.
See below snap for example,
root@OpenWrt:/# iw reg get | grep country
country FR: DFS-ETSI
country FR: DFS-ETSI
country FR: DFS-ETSI
country FR: DFS-ETSI
root@OpenWrt:/# echo assert > /sys/kernel/debug/ath11k/ipq8074\ hw2.0/simulate_f
w_crash
<snip>
[ 5290.471696] ath11k c000000.wifi1: pdev 1 successfully recovered
root@OpenWrt:/# iw reg get | grep country
country FR: DFS-ETSI
country US: DFS-FCC
country US: DFS-FCC
country US: DFS-FCC
In the above, the user configured country 'FR' is overwritten
when the rules of default country 'US' are received and updated during
recovery. Hence avoid processing of these rules in general
during firmware recovery as they have been already applied during
driver registration or after last set user country is configured.
This scenario applies for both AP and STA devices basically because
cfg80211 is not aware of the recovery and only the driver recovers, but
changing or resetting of the reg domain during recovery is not needed so
as to continue with the configured regdomain currently in use.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01460-QCAHKSWPL_SILICONZ-1
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210721212029.142388-3-jouni@codeaurora.org
Update the fields of pdev tx and tx firmware stats structure.
Missing fields resulted in wrong fw stats to be displayed as below.
root@OpenWrt:/# cat /sys/kernel/debug/ath11k/
ipq8074\ hw2.0/mac0/fw_stats/pdev_stats | grep Illegal
Illegal rate phy errors 36839112
Note that this struct was missing its members from initial driver
support and this change doesn't introduce/modify the structure for
firmware changes.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01734-QCAHKSWPL_SILICONZ-1 v2
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210721212029.142388-2-jouni@codeaurora.org
Fix sending rx_buf_sz to ath11k_dp_tx_htt_rx_filter_setup()
to enable pktlog full or lite mode. Depending on mode update the
trace buffer with log type full/lite.
Pktlog lite is a lighter version of pktlog. This can be used to capture
PPDU stats. These are useful for firmware performance debugging.
pktlog lite dumps are enabled using,
echo "0x0 1" > ath11k/IPQ8074 hw2.0/mac0/pktlog_filter
Tested On: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01233-QCAHKSWPL_SILICONZ-1 v2
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210721212029.142388-1-jouni@codeaurora.org
Add support for rx decapsulation offload by advertising
the support to mac80211 during registration. Also ensure
the frames have the RX_FLAG_8023 flag set in decap offload
frames before passing to mac80211.
Since the packets delivered to the driver are in 802.3 format, these
can be sent to the network core with minimal processing in mac80211.
This helps in releasing some CPU cycles in the host processor and
thereby improving the performance.
Two exceptions are made before passing decap frames, one is
for EAPOL packets since mac80211 8023 fast rx for the sta
is set only after authorization, other case is for multicast
packets to validate PN in mac80211. In both the cases the
decap frames are converted to 80211 frame and sent to mac80211.
Ethernet decap can be enabled by using frame_mode modparam:
insmod ath11k frame_mode=2
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-00844-QCAHKSWPL_SILICONZ-1 v2
Co-developed-by: Manikanta Pubbisetty <mpubbise@codeaurora.org>
Signed-off-by: Manikanta Pubbisetty <mpubbise@codeaurora.org>
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210721204217.120572-1-jouni@codeaurora.org
When CONFIG_MODULE_UNLOAD is disabled, the module->exit member
is not defined, causing a build failure:
kernel/module.c:4493:8: error: no member named 'exit' in 'struct module'
mod->exit = *exit;
add an #ifdef block around this.
Fixes: cf68fffb66 ("add support for Clang CFI")
Acked-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Sami Tolvanen <samitolvanen@google.com>
Reviewed-by: Miroslav Benes <mbenes@suse.cz>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jessica Yu <jeyu@kernel.org>
The ath11k_dbring_bufs_replenish() and ath11k_dbring_fill_bufs()
take a "gfp" parameter but they since they take spinlocks, the
allocations they do have to be atomic. This causes a bug because
ath11k_dbring_buf_setup passes GFP_KERNEL for the gfp flags.
The fix is to use GFP_ATOMIC and remove the unused parameters.
Fixes: bd6478559e ("ath11k: Add direct buffer ring support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210812070434.GE31863@kili
qmi tries to allocate a large contiguous dma memory at first,
on the AMD Ryzen platform it fails, then retries with small slices.
So set flag GFP_NOWARN to avoid flooding dmesg.
Signed-off-by: Aaron Ma <aaron.ma@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210823063258.37747-1-aaron.ma@canonical.com
There is a regular need in the kernel to provide a way to declare having a
dynamically sized set of trailing elements in a structure. Kernel code
should always use "flexible array members"[1] for these cases. The older
style of one-element or zero-length arrays should no longer be used[2].
Refactor the code a bit according to the use of a flexible-array member in
struct scan_chan_list_params instead of a one-element array, and use the
struct_size() helper.
Also, save 25 (too many) bytes that were being allocated:
$ pahole -C channel_param drivers/net/wireless/ath/ath11k/reg.o
struct channel_param {
u8 chan_id; /* 0 1 */
u8 pwr; /* 1 1 */
u32 mhz; /* 2 4 */
/* Bitfield combined with next fields */
u32 half_rate:1; /* 4:16 4 */
u32 quarter_rate:1; /* 4:17 4 */
u32 dfs_set:1; /* 4:18 4 */
u32 dfs_set_cfreq2:1; /* 4:19 4 */
u32 is_chan_passive:1; /* 4:20 4 */
u32 allow_ht:1; /* 4:21 4 */
u32 allow_vht:1; /* 4:22 4 */
u32 allow_he:1; /* 4:23 4 */
u32 set_agile:1; /* 4:24 4 */
u32 psc_channel:1; /* 4:25 4 */
/* XXX 6 bits hole, try to pack */
u32 phy_mode; /* 8 4 */
u32 cfreq1; /* 12 4 */
u32 cfreq2; /* 16 4 */
char maxpower; /* 20 1 */
char minpower; /* 21 1 */
char maxregpower; /* 22 1 */
u8 antennamax; /* 23 1 */
u8 reg_class_id; /* 24 1 */
/* size: 25, cachelines: 1, members: 21 */
/* sum members: 23 */
/* sum bitfield members: 10 bits, bit holes: 1, sum bit holes: 6 bits */
/* last cacheline: 25 bytes */
} __attribute__((__packed__));
as previously, sizeof(struct scan_chan_list_params) was 32 bytes:
$ pahole -C scan_chan_list_params drivers/net/wireless/ath/ath11k/reg.o
struct scan_chan_list_params {
u32 pdev_id; /* 0 4 */
u16 nallchans; /* 4 2 */
struct channel_param ch_param[1]; /* 6 25 */
/* size: 32, cachelines: 1, members: 3 */
/* padding: 1 */
/* last cacheline: 32 bytes */
};
and now with the flexible array transformation it is just 8 bytes:
$ pahole -C scan_chan_list_params drivers/net/wireless/ath/ath11k/reg.o
struct scan_chan_list_params {
u32 pdev_id; /* 0 4 */
u16 nallchans; /* 4 2 */
struct channel_param ch_param[]; /* 6 0 */
/* size: 8, cachelines: 1, members: 3 */
/* padding: 2 */
/* last cacheline: 8 bytes */
};
This helps with the ongoing efforts to globally enable -Warray-bounds and
get us closer to being able to tighten the FORTIFY_SOURCE routines on
memcpy().
This issue was found with the help of Coccinelle and audited and fixed,
manually.
[1] https://en.wikipedia.org/wiki/Flexible_array_member
[2] https://www.kernel.org/doc/html/v5.10/process/deprecated.html#zero-length-and-one-element-arrays
Link: https://github.com/KSPP/linux/issues/79
Link: https://github.com/KSPP/linux/issues/109
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210823172159.GA25800@embeddedor
Firmware updates EEPROM support capability in QMI FW caps, send QMI BDF
download request message with file type EEPROM, to get caldata download
from EEPROM. Firmware takes more time to update cal data from EEPROM, so
increase QMI timeout.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1-01838-QCAHKSWPL_SILICONZ-1
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210721201927.100369-5-jouni@codeaurora.org
In current code, AHB/PCI uses two separate functions to download
BDF file. Refactor code and make a common function to send QMI BDF
download request for both AHB and PCI devices. This patch has no
functional change.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00009-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1-01838-QCAHKSWPL_SILICONZ-1
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210721201927.100369-3-jouni@codeaurora.org
Reuse board_size from hw_params, add cal_offset to hw params.
This patch is clean up only, there is no change in functionality.
cal_size was unused, so remove that.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00009-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1-01838-QCAHKSWPL_SILICONZ-1
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210721201927.100369-2-jouni@codeaurora.org
The current what expressions:
What: /sys/bus/platform/drivers/ufshcd/*/...
Doesn't actually match what (some?) platform drivers actually
export. For instance, drivers/scsi/ufs/ufs-hisi.c actually
creates the sysfs struct for ufshcd inside this directory:
/sys/devices/platform/soc/ff3c0000.ufs
Which has those aliases:
/sys/devices/virtual/devlink/platform:fff35000.crg_ctrl--platform:ff3c0000.ufs/consumer/
/sys/bus/platform/drivers/ufshcd-hisi/ff3c0000.ufs/
/sys/bus/platform/devices/soc/ff3c0000.ufs/
/sys/bus/platform/devices/ff3c0000.ufs/
So, add another What: for such files that will match the
device ufs entries, e. g.:
What: /sys/bus/platform/devices/*.ufs/
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Link: https://lore.kernel.org/r/bc61469964bbcabe38d12aa88f2734d38a8741e5.1632750608.git.mchehab+huawei@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are some PCI ABI that aren't shown under:
/sys/bus/pci/drivers/.../
Because they're registered with a different class. That's
the case of, for instance:
/sys/bus/i2c/drivers/CHT Whiskey Cove PMIC/unbind
This one is not present under /sys/bus/pci:
$ find /sys/bus/pci -name 'CHT Whiskey Cove PMIC'
Although clearly this is provided by a PCI driver:
/sys/devices/pci0000:00/0000:00:02.0/i2c-4/subsystem/drivers/CHT Whiskey Cove PMIC/unbind
So, add an altertate What location in order to match bind/unbind
to such devices.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Link: https://lore.kernel.org/r/15ba8c07f1b0fd7359106920c8e34a7b9af7aea6.1632750608.git.mchehab+huawei@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Changeset 8d4b9d1bfe ("PM / Runtime: Add runtime PM statistics (v3)")
added runtime_active_time and runtime_suspended_time, in order
to allow powertop to identify the amount of time a device is
active/suspended.
Add an ABI description for those.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Link: https://lore.kernel.org/r/d5524b966d081c650121c4c496c2f7ab3df524e9.1632750608.git.mchehab+huawei@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of placing almost everything there as a text, use
the proper What: for each component of the ABI.
This allows it to be better documented and parsed by
get_abi.pl.
While here, use wildcards for MODULENAME.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Link: https://lore.kernel.org/r/35876c1eabbcd03170d658081030db980b403297.1632750608.git.mchehab+huawei@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Originally, get_abi.pl was using spaces to separate What: parameters,
but there are several references that declare things like:
/sys/class/powercap/.../<power zone>/enabled
So, the logic was changes in order to properly address it.
That broke the second What added by
Changeset 18e49b3046 ("ABI: security: fix location for evm and ima_policy").
As the only file that defines multiple What: at the same line is
this file, let's move the second What: to a separate line.
Fixes: 18e49b3046 ("ABI: security: fix location for evm and ima_policy")
Fixes: ab9c14805b ("scripts: get_abi.pl: Better handle multiple What parameters")
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Link: https://lore.kernel.org/r/1f1e29ccdc0dd0ec089a67b8a4e9650517c6137a.1632823172.git.mchehab+huawei@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As parsing the sysfs entries can take a long time, add
progress information.
The progress logic will update the stats on every second,
or on 1% steps of the progress.
When STDERR is a console, it will use a single line, using
a VT-100 command to erase the line before rewriting it.
Otherwise, it will put one message on a separate line.
That would help to identify what parts of sysfs checking
that it is taking more time to process.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Link: https://lore.kernel.org/r/4e581dcbec21ad8a60fff883498018f96f13dd1c.1632823172.git.mchehab+huawei@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current highlight schema is not working properly. So, use,
instead, Pod::Text.
While here, also update the copyright in order to reflect the latest
changes and the e-mail I'm currently using.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Link: https://lore.kernel.org/r/89fcd301e065ed86dfd8670725144b196266b6a4.1632750315.git.mchehab+huawei@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It doesn't make any sense to parse ABI entries under
/sys/firmware, as those are either specified by ACPI specs
or by Documentation/devicetree.
The current logic to ignore firmware entries is incomplete,
as it ignores just the relative name of the file, and not
its absolute name. This cause errors while parsing the
symlinks.
So, rewrite the logic for it to do a better job.
Tested with both x86 and arm64 (HiKey970) systems.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Link: https://lore.kernel.org/r/1c806eaec96f6706db4b041bbe6a0e2519e9637e.1632750315.git.mchehab+huawei@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The logic under graph_add_file should create, for every entry, a
__name name array for all entries of the tree. If this fails, the
symlink parsing will break.
Add an error if this ever happens.
While here, improve the output of data dumper to be more
compact and to avoid displaying things like $VAR1=.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Link: https://lore.kernel.org/r/e7dd4d70e206723455d50c851802c8bb6c34941d.1632750315.git.mchehab+huawei@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Changeset 70f400d4d9 ("driver core: Move the "removable" attribute from USB to core")
added a table to the file, but not using a valid ReST format.
Change it to avoid build issues when producing documentation with
"make htmldocs".
Fixes: 70f400d4d9 ("driver core: Move the "removable" attribute from USB to core")
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Link: https://lore.kernel.org/r/bf83354747b8abaa486fe03af4be2826363469cb.1632740376.git.mchehab+huawei@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Changeset af6cbe09920 ("usb: gadget: f_uac2: add volume and mute support")
added some new elements to the table but didn't care enough to actually
adjust the columns, causing the output to be broken as warned by
Sphinx when producing the documentation.
Readjust it for it to be a valid ReST table.
Fixes: eaf6cbe099 ("usb: gadget: f_uac2: add volume and mute support")
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Link: https://lore.kernel.org/r/d253819a4c201b942d754682bb91dd278300fb79.1632740376.git.mchehab+huawei@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Changeset 0356e6283c ("usb: gadget: f_uac1: add volume and mute support")
added some new elements to the table but didn't care enough to actually
adjust the columns, causing the output to be broken as warned by
Sphinx when producing the documentation.
Readjust it for it to be a valid ReST table.
Fixes: 0356e6283c ("usb: gadget: f_uac1: add volume and mute support")
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Link: https://lore.kernel.org/r/044b0c14c35922bdcca50551fe2aa870baae9b06.1632740376.git.mchehab+huawei@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As described at Documentation/ABI/README doesn't contain an
Attribute: field.
The way sysfs ABI is supposed to work is that each different
attribute would have a separate file. So, the right way to
map this would be like:
/sys/.../dell_privacy_supported_type/mic_mute
/sys/.../dell_privacy_supported_type/camera_shutter
/sys/.../dell_privacy_current_state/mic_mute
/sys/.../dell_privacy_current_state/camera_shutter
However, it seems to late to fix that, as this was merged already on
Kernel 5.13, and a change right now would be a regression.
So, instead, let's at least fix the entry to match the expected
format.
While here, fix the format of the contact, which is not a valid
e-mail URL.
This should also fix the current warnings produced when building the
docs:
Documentation/ABI/testing/sysfs-platform-dell-privacy-wmi:35: WARNING: Unexpected indentation.
Documentation/ABI/testing/sysfs-platform-dell-privacy-wmi:2: WARNING: Unexpected indentation.
Fixes: 8af9fa37b8 ("platform/x86: dell-privacy: Add support for Dell hardware privacy")
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Link: https://lore.kernel.org/r/42846621fdf2bf206feb114d06b14cbc47475fb5.1632740376.git.mchehab+huawei@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As warned, /sys/bus/iio/devices/iio:deviceX/fault_ovuv is defined 2 times:
Warning: /sys/bus/iio/devices/iio:deviceX/fault_ovuv is defined 2 times: ./Documentation/ABI/testing/sysfs-bus-iio-temperature-max31856:14 ./Documentation/ABI/testing/sysfs-bus-iio-temperature-max31865:0
The logic with joins the two entries is just places the paragraph
for the second entry after the previous one. That could cause more
warnings, as the produced ReST may become invalid, as in the case of
this specific symbol, which ends with a table:
/new_devel/v4l/docs/Documentation/ABI/testing/sysfs-bus-iio-temperature-max31856:2: WARNING: Malformed table.
No bottom table border found or no blank line after table bottom.
=== =======================================================
'1' The input voltage is negative or greater than VDD.
'0' The input voltage is positive and less than VDD (normal
state).
=== =======================================================
/new_devel/v4l/docs/Documentation/ABI/testing/sysfs-bus-iio-temperature-max31856:2: WARNING: Blank line required after table.
Address it by adding two blank lines before joining duplicated
symbols.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Link: https://lore.kernel.org/r/4ad2e3a65f781f0f8d40bb75aa5a07aca80564d6.1632740376.git.mchehab+huawei@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
HyperFlash devices in Renesas SoCs use 2-bytes addressing, according
to HW manual paragraph 62.3.3 (which officially describes Serial Flash
access, but seems to be applicable to HyperFlash too). And 1-byte bus
read operations to 2-bytes unaligned addresses in external address space
read mode work incorrectly (returns the other byte from the same word).
Function memcpy_fromio(), used by the driver to read data from the bus,
in ARM64 architecture (to which Renesas cores belong) uses 8-bytes
bus accesses for appropriate aligned addresses, and 1-bytes accesses
for other addresses. This results in incorrect data read from HyperFlash
in unaligned cases.
This issue can be reproduced using something like the following commands
(where mtd1 is a parition on Hyperflash storage, defined properly
in a device tree):
[Correct fragment, read from Hyperflash]
root@rcar-gen3:~# dd if=/dev/mtd1 of=/tmp/zz bs=32 count=1
root@rcar-gen3:~# hexdump -C /tmp/zz
00000000 f4 03 00 aa f5 03 01 aa f6 03 02 aa f7 03 03 aa |................|
00000010 00 00 80 d2 40 20 18 d5 00 06 81 d2 a0 18 a6 f2 |....@ ..........|
00000020
[Incorrect read of the same fragment: see the difference at offsets 8-11]
root@rcar-gen3:~# dd if=/dev/mtd1 of=/tmp/zz bs=12 count=1
root@rcar-gen3:~# hexdump -C /tmp/zz
00000000 f4 03 00 aa f5 03 01 aa 03 03 aa aa |............|
0000000c
Fix this issue by creating a local replacement of the copying function,
that performs only properly aligned bus accesses, and is used for reading
from HyperFlash.
Fixes: ca7d8b980b ("memory: add Renesas RPC-IF driver")
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Link: https://lore.kernel.org/r/20210922184830.29147-1-andrew_gabbasov@mentor.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>