commit 6334b8e455 upstream.
When ncm function is working and then stop usb0 interface for link down,
eth_stop() is called. At this piont, accidentally if usb transport error
should happen in usb_ep_enable(), 'in_ep' and/or 'out_ep' may not be enabled.
After that, ncm_disable() is called to disable for ncm unbind
but gether_disconnect() is never called since 'in_ep' is not enabled.
As the result, ncm object is released in ncm unbind
but 'dev->port_usb' associated to 'ncm->port' is not NULL.
And when ncm bind again to recover netdev, ncm object is reallocated
but usb0 interface is already associated to previous released ncm object.
Therefore, once usb0 interface is up and eth_start_xmit() is called,
released ncm object is dereferrenced and it might cause use-after-free memory.
[function unlink via configfs]
usb0: eth_stop dev->port_usb=ffffff9b179c3200
--> error happens in usb_ep_enable().
NCM: ncm_disable: ncm=ffffff9b179c3200
--> no gether_disconnect() since ncm->port.in_ep->enabled is false.
NCM: ncm_unbind: ncm unbind ncm=ffffff9b179c3200
NCM: ncm_free: ncm free ncm=ffffff9b179c3200 <-- released ncm
[function link via configfs]
NCM: ncm_alloc: ncm alloc ncm=ffffff9ac4f8a000
NCM: ncm_bind: ncm bind ncm=ffffff9ac4f8a000
NCM: ncm_set_alt: ncm=ffffff9ac4f8a000 alt=0
usb0: eth_open dev->port_usb=ffffff9b179c3200 <-- previous released ncm
usb0: eth_start dev->port_usb=ffffff9b179c3200 <--
eth_start_xmit()
--> dev->wrap()
Unable to handle kernel paging request at virtual address dead00000000014f
This patch addresses the issue by checking if 'ncm->netdev' is not NULL at
ncm_disable() to call gether_disconnect() to deassociate 'dev->port_usb'.
It's more reasonable to check 'ncm->netdev' to call gether_connect/disconnect
rather than check 'ncm->port.in_ep->enabled' since it might not be enabled
but the gether connection might be established.
Signed-off-by: Norihiko Hama <Norihiko.Hama@alpsalpine.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20240327023550.51214-1-Norihiko.Hama@alpsalpine.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d920a2ed86 upstream.
SanDisks USB3 storage may disapper after system reboot:
usb usb2-port3: link state change
xhci_hcd 0000:00:14.0: clear port3 link state change, portsc: 0x2c0
usb usb2-port3: do warm reset, port only
xhci_hcd 0000:00:14.0: xhci_hub_status_data: stopping usb2 port polling
xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x2b0, return 0x2b0
usb usb2-port3: not warm reset yet, waiting 50ms
xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x2f0, return 0x2f0
usb usb2-port3: not warm reset yet, waiting 200ms
...
xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x6802c0, return 0x7002c0
usb usb2-port3: not warm reset yet, waiting 200ms
xhci_hcd 0000:00:14.0: clear port3 reset change, portsc: 0x4802c0
xhci_hcd 0000:00:14.0: clear port3 warm(BH) reset change, portsc: 0x4002c0
xhci_hcd 0000:00:14.0: clear port3 link state change, portsc: 0x2c0
xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x2c0, return 0x2c0
usb usb2-port3: not enabled, trying warm reset again...
This is due to the USB device still cause port change event after xHCI is
shuted down:
xhci_hcd 0000:38:00.0: // Setting command ring address to 0xffffe001
xhci_hcd 0000:38:00.0: xhci_resume: starting usb3 port polling.
xhci_hcd 0000:38:00.0: xhci_hub_status_data: stopping usb4 port polling
xhci_hcd 0000:38:00.0: xhci_hub_status_data: stopping usb3 port polling
xhci_hcd 0000:38:00.0: hcd_pci_runtime_resume: 0
xhci_hcd 0000:38:00.0: xhci_shutdown: stopping usb3 port polling.
xhci_hcd 0000:38:00.0: // Halt the HC
xhci_hcd 0000:38:00.0: xhci_shutdown completed - status = 1
xhci_hcd 0000:00:14.0: xhci_shutdown: stopping usb1 port polling.
xhci_hcd 0000:00:14.0: // Halt the HC
xhci_hcd 0000:00:14.0: xhci_shutdown completed - status = 1
xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x1203, return 0x203
xhci_hcd 0000:00:14.0: set port reset, actual port 2-3 status = 0x1311
xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x201203, return 0x100203
xhci_hcd 0000:00:14.0: clear port3 reset change, portsc: 0x1203
xhci_hcd 0000:00:14.0: clear port3 warm(BH) reset change, portsc: 0x1203
xhci_hcd 0000:00:14.0: clear port3 link state change, portsc: 0x1203
xhci_hcd 0000:00:14.0: clear port3 connect change, portsc: 0x1203
xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x1203, return 0x203
usb 2-3: device not accepting address 2, error -108
xhci_hcd 0000:00:14.0: xHCI dying or halted, can't queue_command
xhci_hcd 0000:00:14.0: Set port 2-3 link state, portsc: 0x1203, write 0x11261
xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x1263, return 0x263
xhci_hcd 0000:00:14.0: set port reset, actual port 2-3 status = 0x1271
xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x12b1, return 0x2b1
usb usb2-port3: not reset yet, waiting 60ms
ACPI: PM: Preparing to enter system sleep state S5
xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x12f1, return 0x2f1
usb usb2-port3: not reset yet, waiting 200ms
reboot: Restarting system
The port change event is caused by LPM transition, so disabling LPM at shutdown
to make sure the device is in U0 for warmboot.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20240305065140.66801-1-kai.heng.feng@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1607830dad upstream.
This reverts commit 339f83612f.
It has been found to cause problems in a number of Chromebook devices,
so revert the change until it can be brought back in a safe way.
Link: https://lore.kernel.org/r/385a3519-b45d-48c5-a6fd-a3fdb6bec92f@chromium.org
Reported-by:: Aleksander Morgado <aleksandermj@chromium.org>
Fixes: 339f83612f ("usb: cdc-wdm: close race between read and workqueue")
Cc: stable <stable@kernel.org>
Cc: Oliver Neukum <oneukum@suse.com>
Cc: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5a1ccf0c72 ]
This patch introduces a new USB quirk,
USB_QUIRK_SHORT_SET_ADDRESS_REQ_TIMEOUT, which modifies the timeout value
for the SET_ADDRESS request. The standard timeout for USB request/command
is 5000 ms, as recommended in the USB 3.2 specification (section 9.2.6.1).
However, certain scenarios, such as connecting devices through an APTIV
hub, can lead to timeout errors when the device enumerates as full speed
initially and later switches to high speed during chirp negotiation.
In such cases, USB analyzer logs reveal that the bus suspends for
5 seconds due to incorrect chirp parsing and resumes only after two
consecutive timeout errors trigger a hub driver reset.
Packet(54) Dir(?) Full Speed J(997.100 us) Idle( 2.850 us)
_______| Time Stamp(28 . 105 910 682)
_______|_____________________________________________________________Ch0
Packet(55) Dir(?) Full Speed J(997.118 us) Idle( 2.850 us)
_______| Time Stamp(28 . 106 910 632)
_______|_____________________________________________________________Ch0
Packet(56) Dir(?) Full Speed J(399.650 us) Idle(222.582 us)
_______| Time Stamp(28 . 107 910 600)
_______|_____________________________________________________________Ch0
Packet(57) Dir Chirp J( 23.955 ms) Idle(115.169 ms)
_______| Time Stamp(28 . 108 532 832)
_______|_____________________________________________________________Ch0
Packet(58) Dir(?) Full Speed J (Suspend)( 5.347 sec) Idle( 5.366 us)
_______| Time Stamp(28 . 247 657 600)
_______|_____________________________________________________________Ch0
This 5-second delay in device enumeration is undesirable, particularly
in automotive applications where quick enumeration is crucial
(ideally within 3 seconds).
The newly introduced quirks provide the flexibility to align with a
3-second time limit, as required in specific contexts like automotive
applications.
By reducing the SET_ADDRESS request timeout to 500 ms, the
system can respond more swiftly to errors, initiate rapid recovery, and
ensure efficient device enumeration. This change is vital for scenarios
where rapid smartphone enumeration and screen projection are essential.
To use the quirk, please write "vendor_id:product_id:p" to
/sys/bus/usb/drivers/hub/module/parameter/quirks
For example,
echo "0x2c48:0x0132:p" > /sys/bus/usb/drivers/hub/module/parameters/quirks"
Signed-off-by: Hardik Gajjar <hgajjar@de.adit-jv.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20231027152029.104363-2-hgajjar@de.adit-jv.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a769154c7c ]
- The HCD address_device callback now accepts a user-defined timeout value
in milliseconds, providing better control over command execution times.
- The default timeout value for the address_device command has been set
to 5000 ms, aligning with the USB 3.2 specification. However, this
timeout can be adjusted as needed.
- The xhci_setup_device function has been updated to accept the timeout
value, allowing it to specify the maximum wait time for the command
operation to complete.
- The hub driver has also been updated to accommodate the newly added
timeout parameter during the SET_ADDRESS request.
Signed-off-by: Hardik Gajjar <hgajjar@de.adit-jv.com>
Reviewed-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231027152029.104363-1-hgajjar@de.adit-jv.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 5a1ccf0c72 ("usb: new quirk to reduce the SET_ADDRESS request timeout")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c03ff66dc0 ]
'info' is local to the function. There is no need to zeroing it within
a spin_lock section. Moreover, there is no need to explicitly initialize
the .need_pll_quirk field.
Initialize the structure when defined and remove the now useless memset().
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/08ee42fced6af6bd56892cd14f2464380ab071fa.1679600396.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 321da3dc1f ]
It has been observed that some USB/UAS devices return generic properties
hardcoded in firmware for mode pages for a period of time after a device
has been discovered. The reported properties are either garbage or they do
not accurately reflect the characteristics of the physical storage device
attached in the case of a bridge.
Prior to commit 1e029397d1 ("scsi: sd: Reorganize DIF/DIX code to
avoid calling revalidate twice") we would call revalidate several
times during device discovery. As a result, incorrect values would
eventually get replaced with ones accurately describing the attached
storage. When we did away with the redundant revalidate pass, several
cases were reported where devices reported nonsensical values or would
end up in write-protected state.
An initial attempt at addressing this issue involved introducing a
delayed second revalidate invocation. However, this approach still
left some devices reporting incorrect characteristics.
Tasos Sahanidis debugged the problem further and identified that
introducing a READ operation prior to MODE SENSE fixed the problem and that
it wasn't a timing issue. Issuing a READ appears to cause the devices to
update their state to reflect the actual properties of the storage
media. Device properties like vendor, model, and storage capacity appear to
be correctly reported from the get-go. It is unclear why these devices
defer populating the remaining characteristics.
Match the behavior of a well known commercial operating system and
trigger a READ operation prior to querying device characteristics to
force the device to populate the mode pages.
The additional READ is triggered by a flag set in the USB storage and
UAS drivers. We avoid issuing the READ for other transport classes
since some storage devices identify Linux through our particular
discovery command sequence.
Link: https://lore.kernel.org/r/20240213143306.2194237-1-martin.petersen@oracle.com
Fixes: 1e029397d1 ("scsi: sd: Reorganize DIF/DIX code to avoid calling revalidate twice")
Cc: stable@vger.kernel.org
Reported-by: Tasos Sahanidis <tasos@tasossah.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Tasos Sahanidis <tasos@tasossah.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit b73dd5f999 which is
commit 321da3dc1f upstream.
It is known to cause problems and has asked to be dropped.
Link: https://lore.kernel.org/r/yq1frvvpymp.fsf@ca-mkp.ca.oracle.com
Cc: Tasos Sahanidis <tasos@tasossah.com>
Cc: Ewan D. Milne <emilne@redhat.com>
Cc: Bart Van Assche <bvanassche@acm.org>
Cc: Tasos Sahanidis <tasos@tasossah.com>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: James Bottomley <jejb@linux.ibm.com>
Cc: Sasha Levin <sashal@kernel.org>
Reported-by: John David Anglin <dave.anglin@bell.net>
Reported-by: Cyril Brulebois <kibi@debian.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 12f371e2b6 ]
Function checkdone is only required if QUIRK2 is defined, so add
appropriate #if / #endif around the function.
Cleans up clang scan build warning:
drivers/usb/host/sl811-hcd.c:588:18: warning: unused function
'checkdone' [-Wunused-function]
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://lore.kernel.org/r/20240307111351.1982382-1-colin.i.king@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8774ea7a55 ]
The driver already support the tcpci binding for the i2c_device_id so
add the support for the of_device_id too.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240222210903.208901-3-m.felsch@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2a3b7af120 ]
If an frame was transmitted incomplete to the host, we set the
UVC_STREAM_ERR bit in the header for the last request that is going
to be queued. This way the host will know that it should drop the
frame instead of trying to display the corrupted content.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20240214-uvc-error-tag-v1-2-37659a3877fe@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 80ba43e9f7 upstream.
Among the attribute file callback routines in
drivers/usb/core/sysfs.c, the interface_authorized_store() function is
the only one which acquires a device lock on an ancestor device: It
calls usb_deauthorize_interface(), which locks the interface's parent
USB device.
The will lead to deadlock if another process already owns that lock
and tries to remove the interface, whether through a configuration
change or because the device has been disconnected. As part of the
removal procedure, device_del() waits for all ongoing sysfs attribute
callbacks to complete. But usb_deauthorize_interface() can't complete
until the device lock has been released, and the lock won't be
released until the removal has finished.
The mechanism provided by sysfs to prevent this kind of deadlock is
to use the sysfs_break_active_protection() function, which tells sysfs
not to wait for the attribute callback.
Reported-and-tested by: Yue Sun <samsun1006219@gmail.com>
Reported by: xingwei lee <xrivendell7@gmail.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/linux-usb/CAEkJfYO6jRVC8Tfrd_R=cjO0hguhrV31fDPrLrNOOHocDkPoAA@mail.gmail.com/#r
Fixes: 310d2b4124 ("usb: interface authorization: SysFS part of USB interface authorization")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/1c37eea1-9f56-4534-b9d8-b443438dc869@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3de4f996a0 upstream.
Check the UCSI_CCI_RESET_COMPLETE complete flag before starting
another reset. Use a UCSI_SET_NOTIFICATION_ENABLE command to clear
the flag if it is set.
Signed-off-by: Christian A. Ehrhardt <lk@c--e.de>
Cc: stable <stable@kernel.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Link: https://lore.kernel.org/r/20240320073927.1641788-6-lk@c--e.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6aaceb7d9c upstream.
Some DELL systems don't like UCSI_ACK_CC_CI commands with the
UCSI_ACK_CONNECTOR_CHANGE but not the UCSI_ACK_COMMAND_COMPLETE
bit set. The current quirk still leaves room for races because
it requires two consecutive ACK commands to be sent.
Refactor and significantly simplify the quirk to fix this:
Send a dummy command and bundle the connector change ack with the
command completion ack in a single UCSI_ACK_CC_CI command.
This removes the need to probe for the quirk.
While there define flag bits for struct ucsi_acpi->flags in ucsi_acpi.c
and don't re-use definitions from ucsi.h for struct ucsi->flags.
Fixes: f3be347ea4 ("usb: ucsi_acpi: Quirk to ack a connector change ack cmd")
Cc: stable@vger.kernel.org
Signed-off-by: Christian A. Ehrhardt <lk@c--e.de>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Link: https://lore.kernel.org/r/20240320073927.1641788-5-lk@c--e.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6b5c85ddee upstream.
If a command completes the OPM must send an ack. This applies
to unsupported commands, too.
Send the required ACK for unsupported commands.
Signed-off-by: Christian A. Ehrhardt <lk@c--e.de>
Cc: stable <stable@kernel.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Link: https://lore.kernel.org/r/20240320073927.1641788-4-lk@c--e.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 15b2e71b46 upstream.
Suppose we sleep on the PPM lock after clearing the EVENT_PENDING
bit because the thread for another connector is executing a command.
In this case the command completion of the other command will still
report the connector change for our connector.
Clear the EVENT_PENDING bit under the PPM lock to avoid another
useless call to ucsi_handle_connector_change() in this case.
Fixes: c9aed03a0a ("usb: ucsi: Add missing ppm_lock")
Cc: stable <stable@kernel.org>
Signed-off-by: Christian A. Ehrhardt <lk@c--e.de>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Link: https://lore.kernel.org/r/20240320073927.1641788-2-lk@c--e.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 53f5094fdf upstream.
The attribute writing should return the number of bytes used from the
buffer on success.
Fixes: a7cff92f06 ("usb: typec: USB Power Delivery helpers for ports and partners")
Cc: stable@vger.kernel.org
Signed-off-by: Kyle Tso <kyletso@google.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240319074309.3306579-1-kyletso@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2a587a0352 upstream.
It is possible trigger below warning message from mass storage function,
WARNING: CPU: 6 PID: 3839 at drivers/usb/gadget/udc/core.c:294 usb_ep_queue+0x7c/0x104
pc : usb_ep_queue+0x7c/0x104
lr : fsg_main_thread+0x494/0x1b3c
Root cause is mass storage function try to queue request from main thread,
but other thread may already disable ep when function disable.
As there is no function failure in the driver, in order to avoid effort
to fix warning, change WARN_ON_ONCE() in usb_ep_queue() to pr_debug().
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable@vger.kernel.org
Signed-off-by: yuan linyu <yuanlinyu@hihonor.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20240315020144.2715575-1-yuanlinyu@hihonor.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f4d1960764 upstream.
The show and store callback routines for the "disable" sysfs attribute
file in port.c acquire the device lock for the port's parent hub
device. This can cause problems if another process has locked the hub
to remove it or change its configuration:
Removing the hub or changing its configuration requires the
hub interface to be removed, which requires the port device
to be removed, and device_del() waits until all outstanding
sysfs attribute callbacks for the ports have returned. The
lock can't be released until then.
But the disable_show() or disable_store() routine can't return
until after it has acquired the lock.
The resulting deadlock can be avoided by calling
sysfs_break_active_protection(). This will cause the sysfs core not
to wait for the attribute's callback routine to return, allowing the
removal to proceed. The disadvantage is that after making this call,
there is no guarantee that the hub structure won't be deallocated at
any moment. To prevent this, we have to acquire a reference to it
first by calling hub_get().
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/f7a8c135-a495-4ce6-bd49-405a45e7ea9a@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ee113b860a upstream.
Create hub_get() and hub_put() routines to encapsulate the kref_get()
and kref_put() calls in hub.c. The new routines will be used by the
next patch in this series.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/604da420-ae8a-4a9e-91a4-2d511ff404fb@rowland.harvard.edu
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6661befe41 ]
As runtime PM is enabled, the module can be runtime
suspended when .remove() is called.
Do a pm_runtime_get_sync() to make sure module is active
before doing any register operations.
Doing a pm_runtime_put_sync() should disable the refclk
so no need to disable it again.
Fixes the below warning at module removel.
[ 39.705310] ------------[ cut here ]------------
[ 39.710004] clk:162:3 already disabled
[ 39.713941] WARNING: CPU: 0 PID: 921 at drivers/clk/clk.c:1090 clk_core_disable+0xb0/0xb8
We called of_platform_populate() in .probe() so call the
cleanup function of_platform_depopulate() in .remove().
Get rid of the now unnnecessary dwc3_ti_remove_core().
Without this, module re-load doesn't work properly.
Fixes: e8784c0aec ("drivers: usb: dwc3: Add AM62 USB wrapper driver")
Cc: stable@vger.kernel.org # v5.19+
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20240227-for-v6-9-am62-usb-errata-3-0-v4-1-0ada8ddb0767@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3609699c32 ]
Rename dwc3_data to dwc3_am62 to make it consistent with other
glue drivers, it's clearer that this is am62's specific.
While there, do the same for data variable.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Link: https://lore.kernel.org/r/ZLKoHhJvT+Y6aM+C@lenoch
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 6661befe41 ("usb: dwc3-am62: fix module unload/reload behavior")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit cd5432c712 upstream.
In the scenario of entering hibernation with udisk in the system, if the
udisk was gone or resume fail in the thaw phase of hibernation. Its state
will be set to NOTATTACHED. At this point, usb_hub_wq was already freezed
and can't not handle disconnect event. Next, in the poweroff phase of
hibernation, SYNCHRONIZE_CACHE SCSI command will be sent to this udisk
when poweroff this scsi device, which will cause uas_submit_urbs to be
called to submit URB for sense/data/cmd pipe. However, these URBs will
submit fail as device was set to NOTATTACHED state. Then, uas_submit_urbs
will return a value SCSI_MLQUEUE_DEVICE_BUSY to the caller. That will lead
the SCSI layer go into an ugly loop and system fail to go into hibernation.
On the other hand, when we specially check for -ENODEV in function
uas_queuecommand_lck, returning DID_ERROR to SCSI layer will cause device
poweroff fail and system shutdown instead of entering hibernation.
To fix this issue, let uas_submit_urbs to return original generic error
when submitting URB failed. At the same time, we need to translate -ENODEV
to DID_NOT_CONNECT for the SCSI layer.
Suggested-by: Oliver Neukum <oneukum@suse.com>
Cc: stable@vger.kernel.org
Signed-off-by: Weitao Wang <WeitaoWang-oc@zhaoxin.com>
Link: https://lore.kernel.org/r/20240306180814.4897-1-WeitaoWang-oc@zhaoxin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 339f83612f upstream.
wdm_read() cannot race with itself. However, in
service_outstanding_interrupt() it can race with the
workqueue, which can be triggered by error handling.
Hence we need to make sure that the WDM_RESPONDING
flag is not just only set but tested.
Fixes: afba937e54 ("USB: CDC WDM driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/20240314115132.3907-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fdada0db0b upstream.
This reverts commit 75fd6485cc.
This patch was applied twice by accident, causing probe failures.
Revert the accident.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Fixes: 75fd6485cc ("usb: phy: generic: Get the vbus supply")
Cc: stable <stable@kernel.org>
Reviewed-by: Sean Anderson <sean.anderson@seco.com>
Link: https://lore.kernel.org/r/20240314092628.1869414-1-alexander.stein@ew.tq-group.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f90ce1e04c upstream.
While connecting to a Linux host with CDC_NCM_NTB_DEF_SIZE_TX
set to 65536, it has been observed that we receive short packets,
which come at interval of 5-10 seconds sometimes and have block
length zero but still contain 1-2 valid datagrams present.
According to the NCM spec:
"If wBlockLength = 0x0000, the block is terminated by a
short packet. In this case, the USB transfer must still
be shorter than dwNtbInMaxSize or dwNtbOutMaxSize. If
exactly dwNtbInMaxSize or dwNtbOutMaxSize bytes are sent,
and the size is a multiple of wMaxPacketSize for the
given pipe, then no ZLP shall be sent.
wBlockLength= 0x0000 must be used with extreme care, because
of the possibility that the host and device may get out of
sync, and because of test issues.
wBlockLength = 0x0000 allows the sender to reduce latency by
starting to send a very large NTB, and then shortening it when
the sender discovers that there’s not sufficient data to justify
sending a large NTB"
However, there is a potential issue with the current implementation,
as it checks for the occurrence of multiple NTBs in a single
giveback by verifying if the leftover bytes to be processed is zero
or not. If the block length reads zero, we would process the same
NTB infintely because the leftover bytes is never zero and it leads
to a crash. Fix this by bailing out if block length reads zero.
Cc: stable@vger.kernel.org
Fixes: 427694cfaa ("usb: gadget: ncm: Handle decoding of multiple NTB's in unwrap call")
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Reviewed-by: Maciej Żenczykowski <maze@google.com>
Link: https://lore.kernel.org/r/20240228115441.2105585-1-quic_kriskura@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 014bcf41d9 upstream.
The isd200 sub-driver in usb-storage uses the HEADS and SECTORS values
in the ATA ID information to calculate cylinder and head values when
creating a CDB for READ or WRITE commands. The calculation involves
division and modulus operations, which will cause a crash if either of
these values is 0. While this never happens with a genuine device, it
could happen with a flawed or subversive emulation, as reported by the
syzbot fuzzer.
Protect against this possibility by refusing to bind to the device if
either the ATA_ID_HEADS or ATA_ID_SECTORS value in the device's ID
information is 0. This requires isd200_Initialization() to return a
negative error code when initialization fails; currently it always
returns 0 (even when there is an error).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: syzbot+28748250ab47a8f04100@syzkaller.appspotmail.com
Link: https://lore.kernel.org/linux-usb/0000000000003eb868061245ba7f@google.com/
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable@vger.kernel.org
Reviewed-by: PrasannaKumar Muralidharan <prasannatsmkumar@gmail.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Link: https://lore.kernel.org/r/b1e605ea-333f-4ac0-9511-da04f411763e@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 84fa943d93 ]
This commit resolves an issue in the tegra-xudc USB gadget driver that
incorrectly fetched USB3 PHY instances. The problem stemmed from the
assumption of a one-to-one correspondence between USB2 and USB3 PHY
names and their association with physical USB ports in the device tree.
Previously, the driver associated USB3 PHY names directly with the USB3
instance number, leading to mismatches when mapping the physical USB
ports. For instance, if using USB3-1 PHY, the driver expect the
corresponding PHY name as 'usb3-1'. However, the physical USB ports in
the device tree were designated as USB2-0 and USB3-0 as we only have
one device controller, causing a misalignment.
This commit rectifies the issue by adjusting the PHY naming logic.
Now, the driver correctly correlates the USB2 and USB3 PHY instances,
allowing the USB2-0 and USB3-1 PHYs to form a physical USB port pair
while accurately reflecting their configuration in the device tree by
naming them USB2-0 and USB3-0, respectively.
The change ensures that the PHY and PHY names align appropriately,
resolving the mismatch between physical USB ports and their associated
names in the device tree.
Fixes: b4e19931c9 ("usb: gadget: tegra-xudc: Support multiple device modes")
Cc: stable@vger.kernel.org
Signed-off-by: Wayne Chang <waynec@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/20240307030328.1487748-3-waynec@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b1a8da9ff1 ]
TDK NC0110013M and MM0110113M have custom USB IDs for CP210x,
so we need to add them to the driver.
Signed-off-by: Toru Katagiri <Toru.Katagiri@tdk.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a0d9d86849 ]
The radiation meter has the text MGP Instruments PDS-100G or PDS-100GN
produced by Mirion Technologies. Tested by forcing the driver
association with
echo 10c4 863c > /sys/bus/usb-serial/drivers/cp210x/new_id
and then setting the serial port in 115200 8N1 mode. The device
announces ID_USB_VENDOR_ENC=Silicon\x20Labs and ID_USB_MODEL_ENC=PDS100
Signed-off-by: Christian Häggström <christian.haggstrom@orexplore.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3fb7bc4f3a ]
The GMC IR-USB adapter cable utilizes a FTDI FT232R chip.
Add VID/PID for this adapter so it can be used as serial device via
ftdi_sio.
Signed-off-by: Daniel Vogelbacher <daniel@chaospixel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit be95cc6d71 ]
Currently xhci_map_urb_for_dma() creates a temporary buffer and copies
the SG list to the new linear buffer. But if the kzalloc_node() fails,
then the following sg_pcopy_to_buffer() can lead to crash since it
tries to memcpy to NULL pointer.
So return -ENOMEM if kzalloc returns null pointer.
Cc: stable@vger.kernel.org # 5.11
Fixes: 2017a1e584 ("usb: xhci: Use temporary buffer to consolidate SG")
Signed-off-by: Prashanth K <quic_prashk@quicinc.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240229141438.619372-10-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 600556809f ]
Currently the variable irqflags is being set but is not being used,
it appears it should be used in the call to net2272_probe_fin
rather than IRQF_TRIGGER_LOW being used. Kudos to Uwe Kleine-König
for suggesting the fix.
Cleans up clang scan build warning:
drivers/usb/gadget/udc/net2272.c:2610:15: warning: variable 'irqflags'
set but not used [-Wunused-but-set-variable]
Fixes: ceb80363b2 ("USB: net2272: driver for PLX NET2272 USB device controller")
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20240307181734.2034407-1-colin.i.king@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 75fd6485cc ]
While support for working with a vbus was added, the regulator was never
actually gotten (despite what was documented). Fix this by actually
getting the supply from the device tree.
Fixes: 7acc9973e3 ("usb: phy: generic: add vbus support")
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Link: https://lore.kernel.org/r/20240123225111.1629405-3-sean.anderson@seco.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
