CPU subsystem deepest idle state can lead SoC to low power mode like CxPC
(chip rail power collapse). SoC deepest low power mode requires the PDC
interrupt controller to wake up the SoC as the GIC interrupt controller
is on Cx (chip rail) and will not be functional to wake up the CPU.
PDC monitors both direct SPI interrupts and GPIOs used as interrupts
in SoC low power mode. Further all wake up capable interrupts gets routed
via PDC to GIC when SoC is out of low power mode.
The wake up capable GPIOs used as interrupts were by passing PDC on x1e
with commit 602cb14e31 ("pinctrl: qcom: x1e80100: Bypass PDC wakeup
parent for now") as a result CPU deepest idle state was not added so
far.
The blocker for enabling deepest idle state was GPIO IRQ wakeup support.
The x1e80100 PDC can operate in two modes: pass-through mode (GPIO
IRQs forwarded directly to GIC without latching at PDC) and secondary
controller mode (PDC latches GPIO IRQs and sends them as level IRQs to
GIC).
All the SoCs on Linux so far worked in pass-through mode of PDC.
On some x1e boards the firmware configures the PDC in secondary controller
mode, which caused GPIO interrupt storms as the level latched at PDC gets
never cleared.
The secondary mode is originally a requirement for windows SW platforms
(which could not work with all types of interrupts and require level
interrupts for GPIOs). Initially shipped windows firmware did not have
SCM interface to configure PDC back to pass-through mode if with such
firmware Linux is booted up.
PDC irqchip has got secondary mode and SCM interface support to configure
PDC irqchip mode to pass-through mode on newer firmware where SCM interface
is available and for older firmware on which SCM interface is not present
PDC irqchip works in secondary irqchip mode [1]. Above mentioned commit is
also reverted via [1].
With PDC now working on older firmware as well add the CPU deepest idle
state domain_ss3.
The newly added domain_ss3 state has entry/exit latencies of 2500 us.
The shallower cluster_cl5 state had entry/exit latencies of 2200/4000 us
which are higher than the deeper state. This create an inconsistency that
would confuse the idle governor. Correct cluster_cl5 latencies to 2000 us
each to match production configuration values.
[1] https://lore.kernel.org/linux-arm-msm/20260707-hamoa_pdc_v3-v4-0-dfd1f4a3ae89@oss.qualcomm.com/#t
Tested-by: Daniel J Blueman <daniel@quora.org>
Signed-off-by: Maulik Shah <maulik.shah@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260715-hamoa_pdc_v3-v5-1-00440cfaf711@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The PCIe host bridge is connected to a single PCIe bridge for each
controller instance. Hence, add a node to represent the bridge.
While at it, to align with the newer style of binding, move the phys and
perst to port node.
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Kathiravan Thirumoorthy <kathiravan.thirumoorthy@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260714-pcie_move_to_new_binding-v1-4-6bb25887a0dc@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
To align with the newer style of binding, move the phys, PERST# to the
port node.
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Kathiravan Thirumoorthy <kathiravan.thirumoorthy@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260714-pcie_move_to_new_binding-v1-3-6bb25887a0dc@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
To align with the newer style of binding, move the phys property to the
port node.
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Kathiravan Thirumoorthy <kathiravan.thirumoorthy@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260714-pcie_move_to_new_binding-v1-2-6bb25887a0dc@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
To align with the newer style of binding, move the phys, PERST# to the
port node.
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Kathiravan Thirumoorthy <kathiravan.thirumoorthy@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260714-pcie_move_to_new_binding-v1-1-6bb25887a0dc@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
PMM8654AU is a distinct PMIC variant from PMM8650AU despite sharing the
same PMIC subtype. PMM8654AU implements additional registers added to
the "hlos" register address spaces, so add qcom,pmm8654au-pon as a
fallback to qcom,pmk8350-pon to distinguish it from the baseline
PMK8350 PON implementation.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Rakesh Kota <rakesh.kota@oss.qualcomm.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Link: https://patch.msgid.link/20260724-b4-add_pwrkey_and_resin-v6-1-41acc214d93a@oss.qualcomm.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Direct I/O request's use pages handed to the backing files unchanged, so
the backing's DMA alignment requirement applies. Track dio_mem_align and
advertise it as the device's dma_alignment so we communicate proper
limits and misaligned I/O is rejected here instead of reaching the
backend.
Reviewed-by: Hannes Reinecke <hare@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Link: https://patch.msgid.link/20260720201057.1862857-5-kbusch@meta.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Direct I/O user pages are forwarded to the backing file unchanged, so
the backing's DMA alignment requirement applies to them. Track the
backing's dio_mem_align and advertise it as the loop device's
dma_alignment so we advertise proper limits and misaligned I/O is
rejected here instead of being dispatched to the backend.
Reviewed-by: Hannes Reinecke <hare@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Link: https://patch.msgid.link/20260720201057.1862857-4-kbusch@meta.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
A failed integrity mapping holds a dio reference, so we need to go
through the full bio ending in case there were previously submitted
bio's in the sequence.
Fixes: 2729a60bbf ("block: don't silently ignore metadata for sync read/write")
Reviewed-by: Hannes Reinecke <hare@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Link: https://patch.msgid.link/20260720201057.1862857-3-kbusch@meta.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
blkdev_iov_iter_get_pages() can return various error values, including
EIO, EFAULT, and ENOMEM. Set the actual reported status so user space
can know why an operation failed.
Reviewed-by: Hannes Reinecke <hare@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Link: https://patch.msgid.link/20260720201057.1862857-2-kbusch@meta.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
bq25630_setup() resets the device, disables the watchdog and programs
the charge limits from the battery information. It runs at the end of
bq25630_probe(), that is after the power supply has been registered, so
the device is already exposed to the system while the hardware still
holds its power-on defaults.
power_supply_desc::init runs during registration, after the driver data
and the fwnode are available and before the device is added. Use it for
bq25630_setup() and drop the explicit call from bq25630_probe().
The callback is passed the power supply, so take the driver data from it
and use it for the battery information as well: data->psy is only
assigned once devm_power_supply_register() returns, which is after the
callback has run.
Signed-off-by: Linmao Li <lilinmao@kylinos.cn>
Reviewed-by: Waqar Hameed <waqar.hameed@axis.com>
Link: https://patch.msgid.link/20260730011713.3332913-3-lilinmao@kylinos.cn
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
data->batinfo is only used by bq25630_setup() to program the initial
charge limits, but power_supply_get_battery_info() allocates it on
psy->dev, so it stays around for the lifetime of the device. Nothing
else in the driver uses it.
Get the battery information in bq25630_setup(), just before it is read,
and release it on every path out of that function. The driver data no
longer has to carry the pointer.
Signed-off-by: Linmao Li <lilinmao@kylinos.cn>
Reviewed-by: Waqar Hameed <waqar.hameed@axis.com>
Link: https://patch.msgid.link/20260730011713.3332913-2-lilinmao@kylinos.cn
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Add support for the global clock controller (GCC) on the Qualcomm Maili
SoC by extending the Hawi global clock controller since Maili is identical
to Hawi and has few additional clocks.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Taniya Das <taniya.das@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260730-maili_initial_clock-v4-4-ed52ade264f0@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add device tree bindings for the global clock controller (GCC) on
the Qualcomm Maili SoC by extending the existing Qualcomm Hawi GCC
bindings, since the Maili GCC is identical to the Hawi GCC apart
from a few additional clocks.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Taniya Das <taniya.das@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260730-maili_initial_clock-v4-3-ed52ade264f0@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add bindings documentation for TCSR clock controller on the
Qualcomm Maili SoC.
Maili is a derivative of the Hawi SoC and the tcsr clock controller
is identical to that of Hawi. Therefore Maili uses the fallback
compatible to reuse the Hawi tcsrcc driver.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Taniya Das <taniya.das@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260730-maili_initial_clock-v4-2-ed52ade264f0@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Document the RPMH clock controller for the Qualcomm Maili SoC.
Maili SoC is a derivative of the Hawi SoC and the rpmh clock controller
is identical to that of Hawi. Therefore Maili uses the fallback
compatible to reuse the Hawi rpmhcc driver.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Taniya Das <taniya.das@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260730-maili_initial_clock-v4-1-ed52ade264f0@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
origin flow:
bio_endio(master_bio); /* may drop active_io to zero */
allow_barrier(conf);
free_r10bio(r10_bio); /* reads conf->geo, returns to pool */
one scenario is:
CPU A (softirq, raid_end_bio_io) CPU B (action_store) --> reshape
================================ ===============================
bio_endio(master_bio)
md_end_clone_io
percpu_ref_put -> 0
wait_event wakeup, and,
mddev_suspend return
raid10_start_reshape:
setup_geo(&conf->geo, new)
...
mempool_destroy(old_pool)
conf->r10bio_pool = new_pool
allow_barrier(conf)
free_r10bio(r10_bio)
put_all_bios:
for (i=0; i<conf->geo.raid_disks; i++)
==> old obj, new geo, OOB
mempool_free(r10_bio, conf->r10bio_pool)
==> old-geometry obj freed into new pool
so .. fix by reorder the flow:
free_r10bio(r10_bio)
bio_endio(master_bio)
allow_barrier(conf)
raid_end_discard_bio() is exactly the same.
Signed-off-by: Chen Cheng <chencheng@fnnas.com>
Link: https://patch.msgid.link/20260711100352.425177-4-chencheng@fnnas.com
Signed-off-by: Yu Kuai <yukuai@fygo.io>
When reshape grows raid_disks, the pool must also switch to new geometry
object size , and allocate a new geometry size pool and replace the old.
But not for shrinking reshape, because regular I/O can still use the
prev geo for sectors that have not crossed reshape_progress yet.
Signed-off-by: Chen Cheng <chencheng@fnnas.com>
Link: https://patch.msgid.link/20260711100352.425177-3-chencheng@fnnas.com
Signed-off-by: Yu Kuai <yukuai@fygo.io>
raid10 needs to resize/swap r10bio_pool when reshape changes
raid_disks, and, don't let new requests keep allocating r10bio
objects from the old pool while that transition is in progress.
suspend and lock array before mddev_start_reshape(), and resume
it on exit.
Other sync_action ops are unchanged.
Signed-off-by: Chen Cheng <chencheng@fnnas.com>
Link: https://patch.msgid.link/20260711100352.425177-2-chencheng@fnnas.com
Signed-off-by: Yu Kuai <yukuai@fygo.io>
checkpatch.pl reports:
WARNING: Prefer 'unsigned int' to bare use of 'unsigned'
Convert the SMEM driver to use the less ambiguous type instead.
Signed-off-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Mukesh Ojha <mukesh.ojha@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260727-topic-smem_dramc-v5-1-66188b3e338d@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
qcom_tzmem_enable() returns -EBUSY if called a second time, but this
causes probe retries to fail permanently if a later step in
qcom_scm_probe() defers after qcom_tzmem_enable() has already succeeded.
Use DO_ONCE() to ensure qcom_tzmem_init() runs exactly once across all
calls in a thread-safe manner. qcom_tzmem_dev is set on every call since
probe retries use the same device pointer. The result of the first
initialisation is cached and returned to every subsequent caller.
Fixes: 40289e35ca ("firmware: qcom: scm: enable the TZ mem allocator")
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Mukesh Ojha <mukesh.ojha@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260724094939.613844-4-mukesh.ojha@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
of_reserved_mem_device_init() adds an entry to a global list with no
devres counterpart. If qcom_scm_probe() fails after the call the
assignment is never cleaned up. A probe retry would add a duplicate
entry, leaking the original one permanently.
Add an err_rmem label that calls of_reserved_mem_device_release() and
route all error paths after of_reserved_mem_device_init() through it.
of_reserved_mem_device_release() is safe to call unconditionally as it
simply walks an empty list when nothing was assigned.
Fixes: a33b2579c8 ("firmware: qcom: scm: add support for SHM bridge memory carveout")
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Mukesh Ojha <mukesh.ojha@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260724094939.613844-3-mukesh.ojha@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
In qcom_scm_probe(), devm_request_threaded_irq() is called before
smp_store_release(&__scm, scm). Two paths can dereference __scm before
it is published, both causing a NULL pointer dereference.
The IRQ handler receives scm via its data argument but passes only wq_ctx
to qcom_scm_waitq_wakeup() and qcom_scm_get_completion(), which then
dereference __scm directly. Thread scm through both functions so the IRQ
handler path never touches __scm.
Non-atomic SMC calls made during probe (e.g. from qcom_tzmem_init via
qcom_scm_shm_bridge_enable) can return WAITQ_SLEEP, causing
qcom_scm_wait_for_wq_completion() to run before __scm is published and
dereference it. Add platform_set_drvdata(pdev, scm) early in probe and
change qcom_scm_wait_for_wq_completion() to take the device pointer and
use dev_get_drvdata() to reach scm, removing any dependency on __scm.
Fixes: 6bf3259922 ("firmware: qcom: scm: Add wait-queue handling logic")
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Mukesh Ojha <mukesh.ojha@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260724094939.613844-2-mukesh.ojha@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
In line with other Glymur-based machines, the Asus Zenbook A16
(UX3607OA) exposes EFI variables through the "uefisecapp".
Add it to the QSEECOM allowlist to enable this access.
Signed-off-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260721-topic-a16_submission-v1-3-8ea213130d05@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Mimic naming pattern commonly found in the ASoC code:
- 'rtd' in case of struct snd_soc_pcm_runtime
- 'runtime' in case of struct snd_pcm_runtime
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://patch.msgid.link/20260729110057.342447-8-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
To make the firmware loading proceduce easier to understand, especially
around restoring DRAM context, rename the following:
catpt_load_images -> catpt_request_dma_load_firmware
catpt_load_image -> catpt_request_load_firmware
catpt_restore_fwimage -> catpt_restore_dram_rodata
catpt_restore_memdumps -> catpt_restore_dram_data
catpt_store_memdumps -> catpt_store_dram_data
For the exact same reason, update a number of comments related to the
subject.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://patch.msgid.link/20260729110057.342447-6-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Initial design assumed the mechanism could be reused for loading
external modules with signatures differing from the Intel's constant. No
users with such characteristics ever appeared rendering the 'signature'
argument useless.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://patch.msgid.link/20260729110057.342447-4-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
All store/restore firmware operations are located in the loader.c file.
All except the "store firmware context" procedure which is manually
called during the runtime suspend, device.c file.
Adding a wrapper alters functional flow slightly - DMA channel is
requested after the DXSTATE IPC rather than before it but this has no
real impact on the procedure.
At the same time, such approach limits number of symbols exposed in the
core.h file and improves code cohesiveness: all catpt_dma_xxx()
definitions in dsp.c, all their usages in loader.c.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://patch.msgid.link/20260729110057.342447-2-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The only used symbol in these four drivers that is provided by
<linux/mod_devicetable.h> is of_device_id and this is also provided by
<linux/platform_device.h>. So drop the unneeded include which brings us
one step closer to removing <linux/mod_devicetable.h>.
Signed-off-by: Uwe Kleine-König (The Capable Hub) <u.kleine-koenig@baylibre.com>
Reviewed-by: Brian Masney <bmasney@redhat.com>
Link: https://lore.kernel.org/r/7b6441aa3b0dba35112ea486bfea3b3171d8527b.1784225976.git.ukleinek@kernel.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
ps8640_aux_transfer_msg() programs the AUX address registers, starts the
AUX transfer, waits for SWAUX_SEND to clear, and reads the AUX status
register. Several of those regmap operations have return values, but the
function only checks a stale ret after the status read.
Propagate failures from the address write, transfer start, completion
poll, and status read. This avoids returning a transfer length when the
bridge register transaction or AUX completion wait failed.
Fixes: 13afcdd727 ("drm/bridge: parade-ps8640: Add support for AUX channel")
Signed-off-by: Pengpeng Hou <pengpeng@iscas.ac.cn>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patch.msgid.link/20260723103509.2-ps8640-v2-pengpeng@iscas.ac.cn
GPLL0 is pretty much guaranteed to be already on (and voted) during boot,
since it's used by the CPU and also various other components such as UART.
We also vote for this bit in the actual GPLL0 definition, which will be set
as soon as any driver in the kernel requires using the GPLL0 clock.
All in all, this makes separately voting for GPLL0 during probe redundant,
especially because the "acpuclock" in the comment is a downstream construct
that does not exist in upstream.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20260706-qcom-clk-mdm9607-fixes-v2-12-745565101869@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Given that this is a dedicated schema for qcom,gcc-mdm9607, we might as
well use the correct memory addresses in the example. This does not
affect the validation itself, but will reduce confusion for readers.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Link: https://lore.kernel.org/r/20260706-qcom-clk-mdm9607-fixes-v2-11-745565101869@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
gcc-mdm9607.c uses "fw_name", so it requires specifying the "xo" and
"sleep_clk" clock source in the device tree. For some reason, this was
never documented in the dt-bindings. Nowadays, qcom,gcc-mdm9607 has a
dedicated schema, so we can just add it to the properties without any
additional conditionals.
Fixes: 6faa7e4ddc ("dt-bindings: clock: Add MDM9607 GCC clock bindings")
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Link: https://lore.kernel.org/r/20260706-qcom-clk-mdm9607-fixes-v2-10-745565101869@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
This clock does not exist in the hardware, it has no consumers and
reading/writing to the registers fails. Drop it from the bindings.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20260706-qcom-clk-mdm9607-fixes-v2-9-745565101869@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The gcc-mdm9607 driver was originally based on gcc-msm8916, but a closer
match nowadays is gcc-msm8909. Looking at the differences between
gcc-mdm9607 and gcc-msm8909, there is quite some confusion around the
definitions for the BIMC PLL.
It turns out the BIMC PLL on MDM9607 is actually an Alpha PLL just like on
MSM8909. We can vote for it using BIT(2), which explains why BIT(3) was
used for GPLL2.
In practice, the BIMC PLL is exclusively controlled by the RPM firmware and
Linux should not touch it. So far, it was defined to model the full clock
hierarchy, but even in read-only mode with CLK_GET_RATE_NOCACHE this is
problematic since the RPM will silently change the clock parents without
notifying Linux about it. The clock framework reads the clock parent only
once during boot, so the resulting rates will still be often wrong.
Follow the example of more recent SoCs and drop the BIMC PLL and all
remaining related clocks to avoid reporting stale status data. This means
we cannot determine the rate of these clocks anymore. This is not a big
problem in practice, since these are NoC-related clocks that are
independently managed through the interconnect subsystem.
Cc: stable@vger.kernel.org
Fixes: 48b7253264 ("clk: qcom: Add MDM9607 GCC driver")
Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260706-qcom-clk-mdm9607-fixes-v2-8-745565101869@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
This clock does not exist on MDM9607. Reading/writing the registers always
results in 0.
Presumably, this definition was mistakenly copied from gcc-msm8916. On
MSM8916, this root clock is used for multimedia subsystems (camera,
display, video). MDM9607 has none of that, so this clock was probably
omitted in the hardware.
There are no users inside gcc-mdm9607, so we can just drop it.
Cc: stable@vger.kernel.org
Fixes: 48b7253264 ("clk: qcom: Add MDM9607 GCC driver")
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20260706-qcom-clk-mdm9607-fixes-v2-7-745565101869@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
This clock does not exist on the specified address on MDM9607.
Reading/writing the registers always results in 0 or crashes. The math in
the frequency table is also broken. GPLL2 on MDM9607 runs at 480 MHz, so:
- F(155000000, P_GPLL2, 6, 0, 0), // 480 MHz/6 = 80 MHz, not 155 MHz
- F(310000000, P_GPLL2, 3, 0, 0), // 480 MHz/3 = 160 MHz, not 310 MHz
Presumably, this definition was mistakenly copied as-is from gcc-msm8916
(which uses 930 MHz for GPLL2). There are no branch consumers of this root
clock inside gcc-mdm9607 (notably, gcc_apss_tcu_clk has bimc_ddr_clk_src as
parent instead of this clock), so we can just drop it.
It seems like this clock does exist on this SoC on a different address, but
since there is no user and reference code for it, it is still better to
drop it.
Cc: stable@vger.kernel.org
Fixes: 48b7253264 ("clk: qcom: Add MDM9607 GCC driver")
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20260706-qcom-clk-mdm9607-fixes-v2-6-745565101869@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
To conform to the specifications of the USB PHY, the reset signal should be
asserted for at least 10us. Guarantee that by increasing the delay for the
USB2_HS_PHY_ONLY_BCR reset control similar to commit dcc6c9fb71 ("clk:
qcom: gcc-msm8909: Increase delay for USB PHY reset").
Cc: stable@vger.kernel.org
Fixes: 48b7253264 ("clk: qcom: Add MDM9607 GCC driver")
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20260706-qcom-clk-mdm9607-fixes-v2-5-745565101869@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
gcc_apss_axi_clk specifies a halt_reg of 0x4601c, but this is already used
by gcc_apss_ahb_clk. The correct value according to the downstream driver
is 0x46020.
Cc: stable@vger.kernel.org
Fixes: 48b7253264 ("clk: qcom: Add MDM9607 GCC driver")
Reviewed-by: Taniya Das <taniya.das@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Link: https://lore.kernel.org/r/20260706-qcom-clk-mdm9607-fixes-v2-4-745565101869@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
MDM9607 is similar to MSM8909, where the GCC_BLSP1_SLEEP_CBCR register is
read-only and only has the CLK_OFF bit to check if the clock is running.
This is a shared vote clock, the correct way to enable it is to vote for
BLSP1_SLEEP_CLK_ENA (BIT(9)) in GCC_APCS_CLOCK_BRANCH_ENA_VOTE (0x45004).
Cc: stable@vger.kernel.org
Fixes: 48b7253264 ("clk: qcom: Add MDM9607 GCC driver")
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20260706-qcom-clk-mdm9607-fixes-v2-3-745565101869@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
MSM8939 is similar to MSM8916, where the GCC_BLSP1_SLEEP_CBCR register is
read-only and only has the CLK_OFF bit to check if the clock is running.
This is a shared vote clock, the correct way to enable it is to vote for
BLSP1_SLEEP_CLK_ENA (BIT(9)) in GCC_APCS_CLOCK_BRANCH_ENA_VOTE (0x45004).
Cc: stable@vger.kernel.org
Fixes: 1664014e46 ("clk: qcom: gcc-msm8939: Add MSM8939 Generic Clock Controller")
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Link: https://lore.kernel.org/r/20260706-qcom-clk-mdm9607-fixes-v2-2-745565101869@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
According to the APQ8016E TRM, the GCC_BLSP1_SLEEP_CBCR register is
read-only and only has the CLK_OFF bit to check if the clock is running.
This is a shared vote clock, the correct way to enable it is to vote for
BLSP1_SLEEP_CLK_ENA (BIT(9)) in GCC_APCS_CLOCK_BRANCH_ENA_VOTE (0x45004).
Cc: stable@vger.kernel.org
Fixes: 3966fab8b6 ("clk: qcom: Add MSM8916 Global Clock Controller support")
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Link: https://lore.kernel.org/r/20260706-qcom-clk-mdm9607-fixes-v2-1-745565101869@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Since commit
55b48e23f5 ("genirq/devres: Add error handling in devm_request_*_irq()"),
devm_request_threaded_irq() automatically logs detailed error messages on
failure. Remove the now-redundant driver-specific dev_err_probe() call.
Signed-off-by: Pan Chuang <panchuang@vivo.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patch.msgid.link/20260723131649.134127-11-panchuang@vivo.com
