The ifc6410 firmware always enters the kernel in ARM state from
deep idle. Use the cpu_resume_arm() wrapper instead of
cpu_resume() to property switch into the THUMB2 state when we
wake up from idle.
This fixes a problem reported by Kevin Hilman on next-20150601
where the ifc6410 fails to boot a THUMB2 kernel because the
platform's firmware always enters the kernel in ARM mode from
deep idle states.
Reported-by: Kevin Hilman <khilman@linaro.org>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Lina Iyer <lina.iyer@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Some of these are for drivers/soc, where we're now putting
SoC-specific drivers these days. Some are for other driver subsystems
where we have received acks from the appropriate maintainers.
Some highlights:
- simple-mfd: document DT bindings and misc updates
- migrate mach-berlin to simple-mfd for clock, pinctrl and reset
- memory: support for Tegra132 SoC
- memory: introduce tegra EMC driver for scaling memory frequency
- misc. updates for ARM CCI and CCN busses
Conflicts:
arch/arm64/boot/dts/arm/juno-motherboard.dtsi
Trivial add/add conflict with our dt branch.
Resolution: take both sides.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=02Gm
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' into test-merge
ARM: SoC: driver updates for v4.2
Some of these are for drivers/soc, where we're now putting
SoC-specific drivers these days. Some are for other driver subsystems
where we have received acks from the appropriate maintainers.
Some highlights:
- simple-mfd: document DT bindings and misc updates
- migrate mach-berlin to simple-mfd for clock, pinctrl and reset
- memory: support for Tegra132 SoC
- memory: introduce tegra EMC driver for scaling memory frequency
- misc. updates for ARM CCI and CCN busses
Conflicts:
arch/arm64/boot/dts/arm/juno-motherboard.dtsi
Trivial add/add conflict with our dt branch.
Resolution: take both sides.
# gpg: Signature made Wed Jun 24 21:32:17 2015 PDT using RSA key ID D3FBC665
# gpg: Good signature from "Kevin Hilman <khilman@deeprootsystems.com>"
# gpg: aka "Kevin Hilman <khilman@linaro.org>"
# gpg: aka "Kevin Hilman <khilman@kernel.org>"
# Conflicts:
# arch/arm64/boot/dts/arm/juno-motherboard.dtsi
Our SoC branch usually contains expanded support for new SoCs and
other core platform code. Some highlights from this round:
- sunxi: SMP support for A23 SoC
- socpga: big-endian support
- pxa: conversion to common clock framework
- bcm: SMP support for BCM63138
- imx: support new I.MX7D SoC
- zte: basic support for ZX296702 SoC
Conflicts:
arch/arm/mach-socfpga/core.h
Trivial remove/remove conflict with our cleanup branch.
Resolution: remove both sides
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ZtPK
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' into test-merge
ARM: SoC: platform support for v4.2
Our SoC branch usually contains expanded support for new SoCs and
other core platform code. Some highlights from this round:
- sunxi: SMP support for A23 SoC
- socpga: big-endian support
- pxa: conversion to common clock framework
- bcm: SMP support for BCM63138
- imx: support new I.MX7D SoC
- zte: basic support for ZX296702 SoC
Conflicts:
arch/arm/mach-socfpga/core.h
Trivial remove/remove conflict with our cleanup branch.
Resolution: remove both sides
# gpg: Signature made Wed Jun 24 21:32:12 2015 PDT using RSA key ID D3FBC665
# gpg: Good signature from "Kevin Hilman <khilman@deeprootsystems.com>"
# gpg: aka "Kevin Hilman <khilman@linaro.org>"
# gpg: aka "Kevin Hilman <khilman@kernel.org>"
# Conflicts:
# arch/arm/mach-socfpga/core.h
A relatively small setup of cleanups this time around, and similar to last time
the bulk of it is removal of legacy board support:
- OMAP: removal of legacy (non-DT) booting for several platforms
- i.MX: remove some legacy board files
Conflicts: None
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=0zof
-----END PGP SIGNATURE-----
Merge tag 'armsoc-cleanup' into test-merge
ARM: SoC cleanups for v4.2
A relatively small setup of cleanups this time around, and similar to last time
the bulk of it is removal of legacy board support:
- OMAP: removal of legacy (non-DT) booting for several platforms
- i.MX: remove some legacy board files
Conflicts: None
# gpg: Signature made Wed Jun 24 21:32:09 2015 PDT using RSA key ID D3FBC665
# gpg: Good signature from "Kevin Hilman <khilman@deeprootsystems.com>"
# gpg: aka "Kevin Hilman <khilman@linaro.org>"
# gpg: aka "Kevin Hilman <khilman@kernel.org>"
Pull scsi target fixes from Nicholas Bellinger:
"Apologies for the late pull request.
Here are the outstanding target-pending fixes for v4.1 code.
The series contains three patches from Sagi + Co that address a few
iser-target issues that have been uncovered during recent testing at
Mellanox.
Patch #1 has a v3.16+ stable tag, and #2-3 have v3.10+ stable tags"
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
iser-target: Fix possible use-after-free
iser-target: release stale iser connections
iser-target: Fix variable-length response error completion
Pull drm fixes from Dave Airlie:
"A smattering of fixes,
mgag200:
don't accept modes that aren't aligned properly as hw can't do it
i915:
two regression fixes
radeon:
one query to allow userspace fixes
one oops fixer for older hw with new options enabled"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/radeon: don't probe MST on hw we don't support it on
drm/radeon: Add RADEON_INFO_VA_UNMAP_WORKING query
drm/mgag200: Reject non-character-cell-aligned mode widths
Revert "drm/i915: Don't skip request retirement if the active list is empty"
drm/i915: Always reset vma->ggtt_view.pages cache on unbinding
unnoticed by me until recently, hence the late pull request.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=0Lhn
-----END PGP SIGNATURE-----
Merge tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Michael Turquette:
"Very late clk regression fixes for the ARM-based AT91 platform.
These went unnoticed by me until recently, hence the late pull
request"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: at91: fix h32mx prototype inclusion in pmc header
clk: at91: trivial: typo in peripheral clock description
clk: at91: fix PERIPHERAL_MAX_SHIFT definition
clk: at91: pll: fix input range validity check
Trivial fix that prevents to compile this pmc clock driver if h32mx clock is
present but smd clock isn't.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Fixes: bcc5fd49a0 ("clk: at91: add a driver for the h32mx clock")
Cc: <stable@vger.kernel.org> # 3.18+
Fix the PERIPHERAL_MAX_SHIFT definition (3 instead of 4) and adapt the
round_rate and set_rate logic accordingly.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reported-by: "Wu, Songjun" <Songjun.Wu@atmel.com>
The PLL impose a certain input range to work correctly, but it appears that
this input range does not apply on the input clock (or parent clock) but
on the input clock after it has passed the PLL divisor.
Fix the implementation accordingly.
Cc: <stable@vger.kernel.org> # v3.14+
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reported-by: Jonas Andersson <jonas@microbit.se>
one fix, one revert
* tag 'drm-intel-fixes-2015-06-18' of git://anongit.freedesktop.org/drm-intel:
Revert "drm/i915: Don't skip request retirement if the active list is empty"
drm/i915: Always reset vma->ggtt_view.pages cache on unbinding
If you do radeon.mst=1 on a gpu without mst hw, and then
plug some mst hw it will oops instead of falling back.
So check we have DCE5 at least before proceeding.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
This tells userspace that it's safe to use the RADEON_VA_UNMAP operation
of the DRM_RADEON_GEM_VA ioctl.
Cc: stable@vger.kernel.org
(NOTE: Backporting this commit requires at least backports of commits
26d4d129b6,
48afbd70ac and
c29c0876ec as well, otherwise using
RADEON_VA_UNMAP runs into trouble)
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Since when we start discussions about the usage Media Controller for
complex hardware, one thing become clear: the way it is, MC fails to
map anything different than capture/output/m2m video-only streaming.
The point is that MC has entities named as devnodes, but the only
devnode used (before the DVB patches) is MEDIA_ENT_T_DEVNODE_V4L.
Due to the way MC got implemented, however, this entity actually
doesn't represent the devnode, but the hardware I/O engine that
receives data via DMA.
By coincidence, such DMA is associated with the V4L device node
on webcam hardware, but this is not true even for other V4L2
devices. For example, on USB hardware, the DMA is done via the
USB controller. The data passes though a in-kernel filter that
strips off the URB headers. Other V4L2 devices like radio may not
even have DMA. When it have, the DMA is done via ALSA, and not
via the V4L devnode.
In other words, MC is broken as a whole, but tagging it as BROKEN
right now would do more harm than good.
So, instead, let's mark, for now, the DVB part as broken and
block all new changes to MC while we fix this mess, whith
we hopefully will do for the next Kernel version.
Requested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull crypto fixes from Herbert Xu:
"This fixes the following issues:
- Crash in caam hash due to uninitialised buffer lengths.
- Alignment issue in caam RNG that may lead to non-random output"
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: caam - fix RNG buffer cache alignment
crypto: caam - improve initalization for context state saves
The hwrng output buffers (2) are cast inside of a a struct (caam_rng_ctx)
allocated in one DMA-tagged region. While the kernel's heap allocator
should place the overall struct on a cacheline aligned boundary, the 2
buffers contained within may not necessarily align. Consenquently, the ends
of unaligned buffers may not fully flush, and if so, stale data will be left
behind, resulting in small repeating patterns.
This fix aligns the buffers inside the struct.
Note that not all of the data inside caam_rng_ctx necessarily needs to be
DMA-tagged, only the buffers themselves require this. However, a fix would
incur the expense of error-handling bloat in the case of allocation failure.
Cc: stable@vger.kernel.org
Signed-off-by: Steve Cornelius <steve.cornelius@freescale.com>
Signed-off-by: Victoria Milhoan <vicki.milhoan@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Turns out 1366x768 does not in fact work on this hardware.
Signed-off-by: Adam Jackson <ajax@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
With the introduction of multiple views of an obj in the same vm, each
vma was taught to cache its copy of the pages (so that different views
could have different page arrangements). However, this missed decoupling
those vma->ggtt_view.pages when the vma released its reference on the
obj->pages. As we don't always free the vma, this leads to a possible
scenario (e.g. execbuffer interrupted by the shrinker) where the vma
points to a stale obj->pages, and explodes.
Fixes regression from commit fe14d5f4e5
Author: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Date: Wed Dec 10 17:27:58 2014 +0000
drm/i915: Infrastructure for supporting different GGTT views per object
Tvrtko says, if someone else will be confused how this can happen, key
is the reservation execbuffer path. That puts the VMA on the exec_list
which prevents i915_vma_unbind and i915_gem_vma_destroy from fully
destroying the VMA. So the VMA is left existing as an empty object in
the list - unbound and disassociated with the backing store. Kind of a
cached memory object. And then re-using it needs to clear the cached
pages pointer which is fixed above.
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1227892
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Michel Thierry <michel.thierry@intel.com>
Cc: stable@vger.kernel.org
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
[Jani: Added Tvrtko's explanation to commit message.]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Pull dmaengine fixes from Vinod Koul:
"Here are hopefully last set of fixes for 4.1. This time we have:
- fixing pause capability reporting on both dmaengine pause & resume
support by Krzysztof
- locking fix fir at_xdmac by Ludovic
- slave configuration fix for at_xdmac by Ludovic"
* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
dmaengine: Fix choppy sound because of unimplemented resume
dmaengine: at_xdmac: rework slave configuration part
dmaengine: at_xdmac: lock fixes
and an uninitialized variable on Atom platforms.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=L59Q
-----END PGP SIGNATURE-----
Merge tag 'ntb-4.1' of git://github.com/jonmason/ntb
Pull NTB fixes from Jon Mason:
"I apologize for the tardiness of this request. Here are a couple of
last minute NTB bug fixes for v4.1:
NTB bug fixes to address issues in unmapping the MW reg base and
vbase, and an uninitialized variable on Atom platforms"
* tag 'ntb-4.1' of git://github.com/jonmason/ntb:
ntb: initialize max_mw for Atom before using it
ntb: iounmap MW reg and vbase in error path
Pull more MIPS fixes from Ralf Baechle:
"Another round of 4.1 MIPS fixes, one fix to a MIPS-specific #if
condition in lib/mpi, one fix to the MIPS GIC irqchip driver and one
SSB fix.
Details:
- fix handling of clock in chipco SSB driver.
- fix two MIPS-specific #if conditions to correctly work for GCC 5.1.
- fix damage to R6 pgtable bits done by XPA support.
- fix possible crash due to unloading modules that contain statically
defined platform devices.
- fix disabling of the MSA ASE on context switch to also work
correctly when a new thread/process has the CPU for the very first
time.
This is part of linux-next and has been beaten to death on
Imagination's test farm.
While things are not looking too grim this pull request also means the
rate of fixes for 4.1 remains nearly constant so I'd not be unhappy if
you'd delay the release"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MPI: MIPS: Fix compilation error with GCC 5.1
IRQCHIP: mips-gic: Don't nest calls to do_IRQ()
MIPS: MSA: bugfix - disable MSA correctly for new threads/processes.
MIPS: Loongson: Do not register 8250 platform device from module.
MIPS: Cobalt: Do not build MTD platform device registration code as module.
SSB: Fix handling of ssb_pmu_get_alp_clock()
MIPS: pgtable-bits: Fix XPA damage to R6 definitions.
Pull irqchip fix from Thomas Gleixner:
"A single fix for an off by one bug in the sunxi irqchip driver"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip: sunxi-nmi: Fix off-by-one error in irq iterator
The GIC chained handlers use do_IRQ() to call the subhandlers. This
means that irq_enter() calls get nested, which leads to preempt count
looking like we're in nested interrupts, which in turn leads to all
system time being accounted as IRQ time in account_system_time().
Fix it by using generic_handle_irq(). Since these same functions are
used in some systems (if cpu_has_veic) from a low-level vectored
interrupt handler which does not go throught do_IRQ(), we need to do it
conditionally.
Signed-off-by: Rabin Vincent <rabin.vincent@axis.com>
Reviewed-by: Andrew Bresticker <abrestic@chromium.org>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Cc: tglx@linutronix.de
Cc: jason@lakedaemon.net
Patchwork: https://patchwork.linux-mips.org/patch/10545/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Pull networking fixes from David Miller:
1) Fix uninitialized struct station_info in cfg80211_wireless_stats(),
from Johannes Berg.
2) Revert commit attempt to fix ipv6 protocol resubmission, it adds
regressions.
3) Endless loops can be created in bridge port lists, fix from Nikolay
Aleksandrov.
4) Don't WARN_ON() if sk->sk_forward_alloc is non-zero in
sk_clear_memalloc, it is a legal situation during swap deactivation.
Fix from Mel Gorman.
5) Fix order of disabling interrupts and unlocking NAPI in enic driver
to avoid a race. From Govindarajulu Varadarajan.
6) High and low register writes are swapped when programming the start
of periodic output in igb driver. From Richard Cochran.
7) Fix device rename handling in mpls stack, from Robert Shearman.
8) Do not trigger compaction synchronously when optimistically trying
to allocate an order 3 page in alloc_skb_with_frags() and
skb_page_frag_refill(). From Shaohua Li.
9) Authentication with COOKIE_ECHO is not handled properly in SCTP, fix
from Marcelo Ricardo Leitner.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
Doc: networking: Fix URL for wiki.wireshark.org in udplite.txt
sctp: allow authenticating DATA chunks that are bundled with COOKIE_ECHO
net: don't wait for order-3 page allocation
mpls: handle device renames for per-device sysctls
net: igb: fix the start time for periodic output signals
enic: fix memory leak in rq_clean
enic: check return value for stat dump
enic: unlock napi busy poll before unmasking intr
net, swap: Remove a warning and clarify why sk_mem_reclaim is required when deactivating swap
bridge: fix multicast router rlist endless loop
tipc: disconnect socket directly after probe failure
Revert "ipv6: Fix protocol resubmission"
cfg80211: wext: clear sinfo struct before calling driver
Pull block layer fixes from Jens Axboe:
"Remember about a week ago when I sent the last pull request for 4.1?
Well, I lied. Now, I don't want to shift the blame, but Dan, Ming,
and Richard made a liar out of me.
Here are three small patches that should go into 4.1. More
specifically, this pull request contains:
- A Kconfig dependency for the pmem block driver, so it can't be
selected if HAS_IOMEM isn't availble. From Richard Weinberger.
- A fix for genhd, making the ext_devt_lock softirq safe. This makes
lockdep happier, since we also end up grabbing this lock on release
off the softirq path. From Dan Williams.
- A blk-mq software queue release fix from Ming Lei.
Last two are headed to stable, first fixes an issue introduced in this
cycle"
* 'for-linus' of git://git.kernel.dk/linux-block:
block: pmem: Add dependency on HAS_IOMEM
block: fix ext_dev_lock lockdep report
blk-mq: free hctx->ctxs in queue's release handler
The main issue fixed here is a rare race which can result in two reshape
threads running at once, which doesn't end well.
Also a minor issue with a write to a sysfs file returning the wrong value.
Backports to 4.0-stable are indicated.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=wj1j
-----END PGP SIGNATURE-----
Merge tag 'md/4.1-rc7-fixes' of git://neil.brown.name/md
Pull three more md fixes from Neil Brown:
"Hasn't been a good cycle for md has it :-(
The main issue fixed here is a rare race which can result in two
reshape threads running at once, which doesn't end well.
Also a minor issue with a write to a sysfs file returning the wrong
value. Backports to 4.0-stable are indicated"
* tag 'md/4.1-rc7-fixes' of git://neil.brown.name/md:
md: make sure MD_RECOVERY_DONE is clear before starting recovery/resync
md: Close race when setting 'action' to 'idle'.
md: don't return 0 from array_state_store
Pull VT-d hardware workarounds from David Woodhouse:
"This contains a workaround for hardware issues which I *thought* were
never going to be seen on production hardware. I'm glad I checked
that before the 4.1 release...
Firstly, PASID support is so broken on existing chips that we're just
going to declare the old capability bit 28 as 'reserved' and change
the VT-d spec to move PASID support to another bit. So any existing
hardware doesn't support SVM; it only sets that (now) meaningless bit
28.
That patch *wasn't* imperative for 4.1 because we don't have PASID
support yet. But *even* the extended context tables are broken — if
you just enable the wider tables and use none of the new bits in them,
which is precisely what 4.1 does, you find that translations don't
work. It's this problem which I thought was caught in time to be
fixed before production, but wasn't.
To avoid triggering this issue, we now *only* enable the extended
context tables on hardware which also advertises "we have PASID
support and we actually tested it this time" with the new PASID
feature bit.
In addition, I've added an 'intel_iommu=ecs_off' command line
parameter to allow us to disable it manually if we need to"
* git://git.infradead.org/intel-iommu:
iommu/vt-d: Only enable extended context tables if PASID is supported
iommu/vt-d: Change PASID support to bit 40 of Extended Capability Register
Although the extended tables are theoretically a completely orthogonal
feature to PASID and anything else that *uses* the newly-available bits,
some of the early hardware has problems even when all we do is enable
them and use only the same bits that were in the old context tables.
For now, there's no motivation to support extended tables unless we're
going to use PASID support to do SVM. So just don't use them unless
PASID support is advertised too. Also add a command-line bailout just in
case later chips also have issues.
The equivalent problem for PASID support has already been fixed with the
upcoming VT-d spec update and commit bd00c606a ("iommu/vt-d: Change
PASID support to bit 40 of Extended Capability Register"), because the
problematic platforms use the old definition of the PASID-capable bit,
which is now marked as reserved and meaningless.
So with this change, we'll magically start using ECS again only when we
see the new hardware advertising "hey, we have PASID support and we
actually tested it this time" on bit 40.
The VT-d hardware architect has promised that we are not going to have
any reason to support ECS *without* PASID any time soon, and he'll make
sure he checks with us before changing that.
In the future, if hypothetical new features also use new bits in the
context tables and can be seen on implementations *without* PASID support,
we might need to add their feature bits to the ecs_enabled() macro.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
MD_RECOVERY_DONE is normally cleared by md_check_recovery after a
resync etc finished. However it is possible for raid5_start_reshape
to race and start a reshape before MD_RECOVERY_DONE is cleared. This
can lean to multiple reshapes running at the same time, which isn't
good.
To make sure it is cleared before starting a reshape, and also clear
it when reaping a thread, just to be safe.
Signed-off-by: NeilBrown <neilb@suse.de>
Checking ->sync_thread without holding the mddev_lock()
isn't really safe, even after flushing the workqueue which
ensures md_start_sync() has been run.
While this code is waiting for the lock, md_check_recovery could reap
the thread itself, and then start another thread (e.g. recovery might
finish, then reshape starts). When this thread gets the lock
md_start_sync() hasn't run so it doesn't get reaped, but
MD_RECOVERY_RUNNING gets cleared. This allows two threads to start
which leads to confusion.
So don't both if MD_RECOVERY_RUNNING isn't set, but if it is do
the flush and the test and the reap all under the mddev_lock to
avoid any race with md_check_recovery.
Signed-off-by: NeilBrown <neilb@suse.de>
Fixes: 6791875e2e ("md: make reconfig_mutex optional for writes to md sysfs files.")
Cc: stable@vger.kernel.org (v4.0+)
Returning zero from a 'store' function is bad.
The return value should be either len length of the string
or an error.
So use 'len' if 'err' is zero.
Fixes: 6791875e2e ("md: make reconfig_mutex optional for writes to md sysfs files.")
Signed-off-by: NeilBrown <neilb@suse.de>
Cc: stable@vger.kernel (v4.0+)
Some drivers implement only pause operation (no resuming). Example is
pl330 where pause is needed for getting residuum. pl330 does not support
resume operation, transfer must be stopped after pause.
However for slaves this is exposed always as "pause and resume" which
introduces subtle errors on Odroid U3 board (Exynos4412 with pl330).
After adding pause function to pl330 driver the audio playback
(utilizing DMA) gets choppy after some time (approximately 24 hours).
Fix this by exposing "cmd_pause" if and only if pause and resume are
implemented.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reported-by: gabriel@unseen.is
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: <stable@vger.kernel.org>
Fixes: 88987d2c75 ("dmaengine: pl330: add DMA_PAUSE feature")
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Fix for the regression Linus called out, and another for probing
dongles.
* tag 'drm-intel-fixes-2015-06-11' of git://anongit.freedesktop.org/drm-intel:
drm/i915: Fix DDC probe for passive adapters
drm/i915: Properly initialize SDVO analog connectors
Two regression reverts, and two fixes, one for a dpm boot freeze.
* 'drm-fixes-4.1' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: Make sure radeon_vm_bo_set_addr always unreserves the BO
Revert "drm/radeon: adjust pll when audio is not enabled"
Revert "drm/radeon: don't share plls if monitors differ in audio support"
drm/radeon: fix freeze for laptop with Turks/Thames GPU.
Several OMAP2+ hwmod changes for v4.2. One patch cleans up a nasty
interaction between the OMAP GPMC and the hwmod code when debugging is
enabled. IP block integration data has been added for the AM43xx EMIF
RAM controller. There's also a fix for the omap-aes driver when used in
QEMU. And finally, some changes to the OMAP3 hwmod code to support the
use of the security IP blocks (AES and SHA) on GP devices, or when they've
specifically been enabled in the DT data.
Basic build, boot, and power management test results are here:
http://www.pwsan.com/omap/testlogs/omap-hwmod-a-for-v4.2/20150601192349/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=in/l
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.2/soc-pt1-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/soc
Omap hwmod changes for v4.2 via Paul Walmsley <paul@pwsan.com>:
Several OMAP2+ hwmod changes for v4.2. One patch cleans up a nasty
interaction between the OMAP GPMC and the hwmod code when debugging is
enabled. IP block integration data has been added for the AM43xx EMIF
RAM controller. There's also a fix for the omap-aes driver when used in
QEMU. And finally, some changes to the OMAP3 hwmod code to support the
use of the security IP blocks (AES and SHA) on GP devices, or when they've
specifically been enabled in the DT data.
Basic build, boot, and power management test results are here:
http://www.pwsan.com/omap/testlogs/omap-hwmod-a-for-v4.2/20150601192349/
* tag 'omap-for-v4.2/soc-pt1-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP3: Fix crypto support for HS devices
ARM: OMAP2+: Return correct error values from device and hwmod
ARM: OMAP: AM43xx hwmod: Add data for am43xx emif hwmod
memory: omap-gpmc: Add Kconfig option for debug
* zte/soc:
ARM: zx: Add basic defconfig support for ZX296702
ARM: dts: zx: add an initial zx296702 dts and doc
clk: zx: add clock support to zx296702
dt-bindings: Add #defines for ZTE ZX296702 clocks
It adds a clock driver for zx296702 SoC to register the clock tree to
Common Clock Framework. All the clocks of bus topology and some the
peripheral clocks are ready with this commit. Some missing leaf clocks
for peripherals will be added later when needed.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
When programming the start of a periodic output, the code wrongly places
the seconds value into the "low" register and the nanoseconds into the
"high" register. Even though this is backwards, it slipped through my
testing, because the re-arming code in the interrupt service routine is
correct, and the signal does appear starting with the second edge.
This patch fixes the issue by programming the registers correctly.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not all architectures have io memory.
Fixes:
drivers/block/pmem.c: In function ‘pmem_alloc’:
drivers/block/pmem.c:146:2: error: implicit declaration of function ‘ioremap_nocache’ [-Werror=implicit-function-declaration]
pmem->virt_addr = ioremap_nocache(pmem->phys_addr, pmem->size);
^
drivers/block/pmem.c:146:18: warning: assignment makes pointer from integer without a cast [enabled by default]
pmem->virt_addr = ioremap_nocache(pmem->phys_addr, pmem->size);
^
drivers/block/pmem.c:182:2: error: implicit declaration of function ‘iounmap’ [-Werror=implicit-function-declaration]
iounmap(pmem->virt_addr);
^
Signed-off-by: Richard Weinberger <richard@nod.at>
Reviewed-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
- add failure(exception) handling
: of_iomap(), of_find_device_by_node() and kstrdup()
- add common poweroff to use PS_HOLD based for all of exynos SoCs
- add exnos_get/set_boot_addr() helper
- constify platform_device_id and irq_domain_ops
- get current parent clock for power domain on/off
- use core_initcall to register power domain driver
- make exynos_core_restart() less verbose
- add support coupled CPUidle for exynos3250
- fix exynos_boot_secondary() return value on timeout
- fix clk_enable() in s3c24xx adc
- fix missing of_node_put() for power domains
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=LybA
-----END PGP SIGNATURE-----
Merge tag 'samsung-mach-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/soc
Samsung updates for v4.2
- add failure(exception) handling
: of_iomap(), of_find_device_by_node() and kstrdup()
- add common poweroff to use PS_HOLD based for all of exynos SoCs
- add exnos_get/set_boot_addr() helper
- constify platform_device_id and irq_domain_ops
- get current parent clock for power domain on/off
- use core_initcall to register power domain driver
- make exynos_core_restart() less verbose
- add support coupled CPUidle for exynos3250
- fix exynos_boot_secondary() return value on timeout
- fix clk_enable() in s3c24xx adc
- fix missing of_node_put() for power domains
* tag 'samsung-mach-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung: (301 commits)
ARM: EXYNOS: register power domain driver from core_initcall
ARM: EXYNOS: use PS_HOLD based poweroff for all supported SoCs
ARM: SAMSUNG: Constify platform_device_id
ARM: EXYNOS: Constify irq_domain_ops
ARM: EXYNOS: add coupled cpuidle support for Exynos3250
ARM: EXYNOS: add exynos_get_boot_addr() helper
ARM: EXYNOS: add exynos_set_boot_addr() helper
ARM: EXYNOS: make exynos_core_restart() less verbose
ARM: EXYNOS: fix exynos_boot_secondary() return value on timeout
ARM: EXYNOS: Get current parent clock for power domain on/off
ARM: SAMSUNG: fix clk_enable() WARNing in S3C24XX ADC
ARM: EXYNOS: Add missing of_node_put() when parsing power domains
ARM: EXYNOS: Handle of_find_device_by_node() and kstrdup() failures
ARM: EXYNOS: Handle of of_iomap() failure
Linux 4.1-rc4
....
Some error paths didn't unreserve the BO. This resulted in a deadlock
down the road on the next attempt to reserve the (still reserved) BO.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=90873
Cc: stable@vger.kernel.org
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Laptop with Turks/Thames GPU will freeze if dpm is enabled. It seems
the SMC engine is relying on some state inside the CP engine. CP needs
to chew at least one packet for it to get in good state for dynamic
power management.
This patch simply disabled and re-enable DPM after the ring test which
is enough to avoid the freeze.
Signed-off-by: Jérôme Glisse <jglisse@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Commit ab760a0 (ntb: Adding split BAR support for Haswell platforms)
changed ntb_device's mw from a fixed-size array into a pointer that is
allocated based on limits.max_mw; however, on Atom platforms, max_mw
is not initialized until ntb_device_setup(), which happens after the
allocation.
Fill out max_mw in ntb_atom_detect() to match ntb_xeon_detect(); this
happens before the use of max_mw in the ndev->mw allocation.
Fixes a null pointer dereference on Atom platforms with ntb hardware.
v2: fix typo (mw_max should be max_mw)
Signed-off-by: Daniel Verkamp <daniel.verkamp@intel.com>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
We do not check the return value of enic_dev_stats_dump(). If allocation
fails, we will hit NULL pointer reference.
Return only if memory allocation fails. For other failures, we return the
previously recorded values.
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>