Fernando Fernandez Mancera says:
====================
Convert CONFIG_IPV6 to built-in and remove stubs
Historically, the Linux kernel has supported compiling the IPv6 stack as
a loadable module. While this made sense in the early days of IPv6
adoption, modern deployments and distributions overwhelmingly either
build IPv6 directly into the kernel (CONFIG_IPV6=y) or disable it
entirely (CONFIG_IPV6=n). The modular IPv6 use-case offers image size
and memory savings for specific setups, this benefit is outweighed by
the architectural burden it imposes on the subsystems on implementation
and maintenance.
In addition, most of the distributions are already using CONFIG_IPV6=y
by default [1], including openWRT [2] and Android gki_defconfig [3]. So
this won't have an impact on them. The most impacted architecture would
probably be arm64 as their default config is still using CONFIG_IPV6=m.
To allow core networking, BPF, Netfilter, and various device drivers to
safely interact with a potentially unloaded IPv6 module, the kernel
relies on indirect call structures like ipv6_stub, ipv6_bpf_stub, and
nf_ipv6_ops, along with dynamic RCU registrations for things like ICMPv6
senders.
This patch series addresses this by changing CONFIG_IPV6 from a tristate
to a boolean, enforcing that IPv6 is either built-in or disabled. This
allows us to completely rip out the stub infrastructures and safely
replace them with direct function calls.
The bloat-o-meter report the following results for m68k, arm64, x86_64
defconfig.
m68k (keep on mind that CONFIG_IPV6 is disabled now):
add/remove: 65/938 grow/shrink: 36/254 up/down: 3022/-49692 (-46670)
arm64:
add/remove: 1251/265 grow/shrink: 81/46 up/down: 448740/-71519 (377221)
x86_64:
add/remove: 62/98 grow/shrink: 10/39 up/down: 2497/-4357 (-1860)
Considering that each new kernel release increases sizes by 30-40KiB on
average, this size increase isn't a huge jump for the distributions that
are still using CONFIG_IPV6=m. For the ones that are already using
CONFIG_IPV6=y, the size is reduced actually.
All the patches has been independently build tested. With allmodconfig
and allmodconfig + CONFIG_IPV6=n. In addition, net selftest has been run
against them on virtme-ng.
The series applied as a whole as been tested with allyesconfig and also
allyesconfig + CONFIG_IPV6=n but not all patches has been independently
tested this way.
[1] https://github.com/nyrahul/linux-kernel-configs
[2] 832e7b8172
[3] https://android.googlesource.com/kernel/common/+/refs/heads/android-mainline/arch/arm64/configs/gki_defconfig
====================
Link: https://patch.msgid.link/20260325120928.15848-1-fmancera@suse.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As IPv6 is built-in only, nf_ipv6_ops can be removed completely as it is
not longer necessary.
Convert all nf_ipv6_ops usage to direct function calls instead. In
addition, remove the ipv6_netfilter_init/fini() functions as they are
not necessary any longer.
Signed-off-by: Fernando Fernandez Mancera <fmancera@suse.de>
Tested-by: Ricardo B. Marlière <rbm@suse.com>
Link: https://patch.msgid.link/20260325120928.15848-12-fmancera@suse.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As IPv6 is built-in only and there are no more users of ipv6_stub, the
ipv6_stub is now entirely obsolete.
Remove all the code related to the definition, initialization and usage.
Signed-off-by: Fernando Fernandez Mancera <fmancera@suse.de>
Tested-by: Ricardo B. Marlière <rbm@suse.com>
Link: https://patch.msgid.link/20260325120928.15848-11-fmancera@suse.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As IPv6 is built-in only, the ipv6_bpf_stub can be removed completely.
Convert all ipv6_bpf_stub usage to direct function calls instead. The
fallback functions introduced previously will prevent linkage errors
when CONFIG_IPV6 is disabled.
Signed-off-by: Fernando Fernandez Mancera <fmancera@suse.de>
Tested-by: Ricardo B. Marlière <rbm@suse.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Martin KaFai Lau <martin.lau@kernel.org>
Link: https://patch.msgid.link/20260325120928.15848-10-fmancera@suse.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As IPv6 is built-in only, the ipv6_stub infrastructure is no longer
necessary.
Convert remaining ipv6_stub users to make direct function calls. The
fallback functions introduced previously will prevent linkage errors
when CONFIG_IPV6 is disabled.
Signed-off-by: Fernando Fernandez Mancera <fmancera@suse.de>
Tested-by: Ricardo B. Marlière <rbm@suse.com>
Link: https://patch.msgid.link/20260325120928.15848-9-fmancera@suse.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As IPv6 is built-in only, the ipv6_stub infrastructure is no longer
necessary.
The IPv4 stack interacts with IPv6 mainly to support IPv4 routes with
IPv6 next-hops (RFC 8950). Convert all these cross-family calls from
ipv6_stub to direct function calls. The fallback functions introduced
previously will prevent linkage errors when CONFIG_IPV6 is disabled.
Signed-off-by: Fernando Fernandez Mancera <fmancera@suse.de>
Tested-by: Ricardo B. Marlière <rbm@suse.com>
Link: https://patch.msgid.link/20260325120928.15848-8-fmancera@suse.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As IPv6 is built-in only, the ipv6_stub infrastructure is no longer
necessary.
Convert all drivers currently utilizing ipv6_stub to make direct
function calls. The fallback functions introduced previously will
prevent linkage errors when CONFIG_IPV6 is disabled.
Signed-off-by: Fernando Fernandez Mancera <fmancera@suse.de>
Tested-by: Ricardo B. Marlière <rbm@suse.com>
Reviewed-by: Jason A. Donenfeld <Jason@zx2c4.com>
Reviewed-by: Antonio Quartulli <antonio@openvpn.net>
Reviewed-by: Edward Cree <ecree.xilinx@gmail.com>
Link: https://patch.msgid.link/20260325120928.15848-7-fmancera@suse.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In preparation for dropping ipv6_stub and converting its users to direct
function calls, introduce static inline dummy functions and fallback
macros in the IPv6 networking headers. In addition, introduce checks on
fib6_nh_init(), ip6_dst_lookup_flow() and ip6_fragment() to avoid a
crash due to ipv6.disable=1 set during booting. The other functions are
safe as they cannot be called with ipv6.disable=1 set.
These fallbacks ensure that when CONFIG_IPV6 is completely disabled,
there are no compiling or linking errors due to code paths not guarded
by preprocessor macro IS_ENABLED(CONFIG_IPV6).
In addition, export ndisc_send_na(), ip6_route_input() and
ip6_fragment().
Signed-off-by: Fernando Fernandez Mancera <fmancera@suse.de>
Tested-by: Ricardo B. Marlière <rbm@suse.com>
Link: https://patch.msgid.link/20260325120928.15848-6-fmancera@suse.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As IPv6 is built-in only, there is no need to maintain the sender
registration infrastructure used to allow built-in subsystems to send
ICMPv6 messages when IPv6 was compiled as a module.
Drop the registration mechanism and the __icmpv6_send() sender
implementation. While icmpv6_send() users could be converted to
icmp6_send() that doesn't seems necessary as none of them are using the
force_saddr parameter.
Signed-off-by: Fernando Fernandez Mancera <fmancera@suse.de>
Tested-by: Ricardo B. Marlière <rbm@suse.com>
Link: https://patch.msgid.link/20260325120928.15848-5-fmancera@suse.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As IPv6 is built-in only, it does not make sense to continue using
IS_BUILTIN(CONFIG_IPV6). Therefore, replace it with IS_ENABLED() when
necessary and drop it if it isn't valid anymore.
Notice that there is still one instance related to ICMPv6, as it
requires more changes it will be handle separately.
Signed-off-by: Fernando Fernandez Mancera <fmancera@suse.de>
Tested-by: Ricardo B. Marlière <rbm@suse.com>
Acked-by: Martin KaFai Lau <martin.lau@kernel.org>
Link: https://patch.msgid.link/20260325120928.15848-4-fmancera@suse.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As IPv6 is built-in only, the macro is always evaluating to an empty
one. Remove it completely from the code.
Signed-off-by: Fernando Fernandez Mancera <fmancera@suse.de>
Link: https://patch.msgid.link/20260325120928.15848-3-fmancera@suse.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Maintaining a modular IPv6 stack offers image size savings for specific
setups, this benefit is outweighed by the architectural burden it
imposes on the subsystems on implementation and maintenance. Therefore,
drop it.
Change CONFIG_IPV6 from tristate to bool. Remove all Kconfig
dependencies across the tree that explicitly checked for IPV6=m. In
addition, remove MODULE_DESCRIPTION(), MODULE_ALIAS(), MODULE_AUTHOR()
and MODULE_LICENSE().
This is also replacing module_init() by device_initcall(). It is not
possible to use fs_initcall() as IPv4 does because that creates a race
condition on IPv6 addrconf.
Finally, modify the default configs from CONFIG_IPV6=m to CONFIG_IPV6=y
except for m68k as according to the bloat-o-meter the image is
increasing by 330KB~ and that isn't acceptable. Instead, disable IPv6 on
this architecture by default. This is aligned with m68k RAM requirements
and recommendations [1].
[1] http://www.linux-m68k.org/faq/ram.html
Signed-off-by: Fernando Fernandez Mancera <fmancera@suse.de>
Tested-by: Ricardo B. Marlière <rbm@suse.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org> # arm64
Link: https://patch.msgid.link/20260325120928.15848-2-fmancera@suse.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Now that there is snp_prepare() that indicates when the CCP driver wants to
prepare the architecture for SNP_INIT(_EX), move this architecture-specific
bit of code to a more sensible place.
Signed-off-by: Tycho Andersen (AMD) <tycho@kernel.org>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Tom Lendacky <thomas.lendacky@amd.com>
Link: https://patch.msgid.link/20260324161301.1353976-6-tycho@kernel.org
Document the Inter-Processor Communication Controller (IPCC) found in the
Qualcomm Eliza SoC. It is used to route interrupts across various
subsystems.
Signed-off-by: Abel Vesa <abel.vesa@oss.qualcomm.com>
Acked-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com>
- Fix an early boot crash in AMD SEV-SNP guests, caused by incorrect
FSGSBASE init ordering. (Nikunj A Dadhania)
- Remove X86_CR4_FRED from the CR4 pinned bits mask, to fix a race
window during the bootup of SEV-{ES,SNP} or TDX guests, which
can crash them if they trigger exceptions in that window.
(Borislav Petkov)
- Fix early boot failures on SEV-ES/SNP guests, due to incorrect
early GHCB access. (Nikunj A Dadhania)
- Add clarifying comment to the CRn pinning logic, to avoid
future confusion & bugs. (Peter Zijlstra)
Signed-off-by: Ingo Molnar <mingo@kernel.org>
-----BEGIN PGP SIGNATURE-----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=I3Gh
-----END PGP SIGNATURE-----
Merge tag 'x86-urgent-2026-03-29' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
- Fix an early boot crash in AMD SEV-SNP guests, caused by incorrect
FSGSBASE init ordering (Nikunj A Dadhania)
- Remove X86_CR4_FRED from the CR4 pinned bits mask, to fix a race
window during the bootup of SEV-{ES,SNP} or TDX guests, which can
crash them if they trigger exceptions in that window (Borislav
Petkov)
- Fix early boot failures on SEV-ES/SNP guests, due to incorrect early
GHCB access (Nikunj A Dadhania)
- Add clarifying comment to the CRn pinning logic, to avoid future
confusion & bugs (Peter Zijlstra)
* tag 'x86-urgent-2026-03-29' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/cpu: Add comment clarifying CRn pinning
x86/fred: Fix early boot failures on SEV-ES/SNP guests
x86/cpu: Remove X86_CR4_FRED from the CR4 pinned bits mask
x86/cpu: Enable FSGSBASE early in cpu_init_exception_handling()
which may cause missed expirations or incorrect overrun accounting.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
-----BEGIN PGP SIGNATURE-----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=hDiV
-----END PGP SIGNATURE-----
Merge tag 'timers-urgent-2026-03-29' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fix from Ingo Molnar:
"Fix an argument order bug in the alarm timer forwarding logic, which
may cause missed expirations or incorrect overrun accounting"
* tag 'timers-urgent-2026-03-29' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
alarmtimer: Fix argument order in alarm_timer_forward()
- Tighten up the sys_futex_requeue() ABI a bit, to disallow
dissimilar futex flags and potential UaF access. (Peter Zijlstra)
- Fix UaF between futex_key_to_node_opt() and vma_replace_policy()
(Hao-Yu Yang)
- Clear stale exiting pointer in futex_lock_pi() retry path,
which bug triggered a warning (and potential misbehavior)
in stress-testing. (Davidlohr Bueso)
Signed-off-by: Ingo Molnar <mingo@kernel.org>
-----BEGIN PGP SIGNATURE-----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=85AU
-----END PGP SIGNATURE-----
Merge tag 'locking-urgent-2026-03-29' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull futex fixes from Ingo Molnar:
- Tighten up the sys_futex_requeue() ABI a bit, to disallow dissimilar
futex flags and potential UaF access (Peter Zijlstra)
- Fix UaF between futex_key_to_node_opt() and vma_replace_policy()
(Hao-Yu Yang)
- Clear stale exiting pointer in futex_lock_pi() retry path, which
triggered a warning (and potential misbehavior) in stress-testing
(Davidlohr Bueso)
* tag 'locking-urgent-2026-03-29' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
futex: Clear stale exiting pointer in futex_lock_pi() retry path
futex: Fix UaF between futex_key_to_node_opt() and vma_replace_policy()
futex: Require sys_futex_requeue() to have identical flags
Add few more alu32 shift tests using div-by-zero on provably dead paths
to check both verifier and JIT xlation resp. runtime correctness.
If the verifier mistracks the result, it rejects due to the div by 0;
if the JIT computes a wrong value, then runtime hits the dead path and
retval changes.
# LDLIBS=-static PKG_CONFIG='pkg-config --static' ./vmtest.sh -- ./test_progs -t verifier_subreg
[...]
#644/76 verifier_subreg/arsh32_imm1_value:OK
#644/77 verifier_subreg/lsh32_reg0_zero_extend_check:OK
#644/78 verifier_subreg/rsh32_reg0_zero_extend_check:OK
#644/79 verifier_subreg/arsh32_reg0_zero_extend_check:OK
#644/80 verifier_subreg/lsh32_imm31_value:OK
#644/81 verifier_subreg/rsh32_imm31_value:OK
#644/82 verifier_subreg/arsh32_imm31_value:OK
#644/83 verifier_subreg/lsh32_unknown_precise_bounds:OK
#644/84 verifier_subreg/rsh32_unknown_bounds:OK
#644 verifier_subreg:OK
Summary: 1/84 PASSED, 0 SKIPPED, 0 FAILED
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/r/20260327220629.343327-1-daniel@iogearbox.net
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Update selftests to use the new non-_impl kfuncs marked with
KF_IMPLICIT_ARGS by removing redundant declarations and macros from
bpf_experimental.h (the new kfuncs are present in the vmlinux.h) and
updating relevant callsites.
Fix spin_lock verifier-log matching for lock_id_kptr_preserve by
accepting variable instruction numbers. The calls to kfuncs with
implicit arguments do not have register moves (e.g. r5 = 0)
corresponding to dummy arguments anymore, so the order of instructions
has shifted.
Acked-by: Mykyta Yatsenko <yatsenko@meta.com>
Signed-off-by: Ihor Solodrai <ihor.solodrai@linux.dev>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Link: https://lore.kernel.org/r/20260327203241.3365046-2-ihor.solodrai@linux.dev
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
The following kfuncs currently accept void *meta__ign argument:
* bpf_obj_new_impl
* bpf_obj_drop_impl
* bpf_percpu_obj_new_impl
* bpf_percpu_obj_drop_impl
* bpf_refcount_acquire_impl
* bpf_list_push_back_impl
* bpf_list_push_front_impl
* bpf_rbtree_add_impl
The __ign suffix is an indicator for the verifier to skip the argument
in check_kfunc_args(). Then, in fixup_kfunc_call() the verifier may
set the value of this argument to struct btf_struct_meta *
kptr_struct_meta from insn_aux_data.
BPF programs must pass a dummy NULL value when calling these kfuncs.
Additionally, the list and rbtree _impl kfuncs also accept an implicit
u64 argument, which doesn't require __ign suffix because it's a
scalar, and BPF programs explicitly pass 0.
Add new kfuncs with KF_IMPLICIT_ARGS [1], that correspond to each
_impl kfunc accepting meta__ign. The existing _impl kfuncs remain
unchanged for backwards compatibility.
To support this, add "btf_struct_meta" to the list of recognized
implicit argument types in resolve_btfids.
Implement is_kfunc_arg_implicit() in the verifier, that determines
implicit args by inspecting both a non-_impl BTF prototype of the
kfunc.
Update the special_kfunc_list in the verifier and relevant checks to
support both the old _impl and the new KF_IMPLICIT_ARGS variants of
btf_struct_meta users.
[1] https://lore.kernel.org/bpf/20260120222638.3976562-1-ihor.solodrai@linux.dev/
Signed-off-by: Ihor Solodrai <ihor.solodrai@linux.dev>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Link: https://lore.kernel.org/r/20260327203241.3365046-1-ihor.solodrai@linux.dev
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
-----BEGIN PGP SIGNATURE-----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=sSP0
-----END PGP SIGNATURE-----
Merge tag 'ovl-fixes-7.0-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/overlayfs/vfs
Pull overlayfs fixes from Amir Goldstein:
- Fix regression in 'xino' feature detection
I clumsily introduced this regression myself when working on another
subsystem (fsnotify). Both the regression and the fix have almost no
visible impact on users except for some kmsg prints.
- Fix to performance regression in v6.12.
This regression was reported by Google COS developers.
It is not uncommon these days for the year-old mature LTS to get
adopted by distros and get exposed to many new workloads. We made a
sub-smart move of making a behavior change in v6.12 which could
impact performance, without making it opt-in. Fixing this mistake
retroactively, to be picked by LTS.
* tag 'ovl-fixes-7.0-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/overlayfs/vfs:
ovl: make fsync after metadata copy-up opt-in mount option
ovl: fix wrong detection of 32bit inode numbers
During the system suspend process, device interrupts are masked in the
noirq phase. However, SCMI often needs to exchange final messages with the
firmware to complete the power-down transition. Without the IRQF_NO_SUSPEND
flag, the mailbox ISR cannot run during this late stage, leading to SCMI
communication timeouts and error messages like "SCMI protocol wait for
resp timeout" during suspend.
Add the IRQF_NO_SUSPEND flag to the interrupt request to ensure the mailbox
can continue to handle responses during the noirq stages of suspend and
resume, thereby ensuring a reliable power state transition.
Signed-off-by: Dylan Wu <fredwudi0305@gmail.com>
Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com>
Add a test issue an ext4 warning (not a WARN_ON) if there are still
dirty pages attached to an evicted inode.
A lot of ext4 bug fixes including:
* Fix a number of Syzkaller issues.
* Fix memory leaks on error paths.
* Replace some BUG and WARN with EFSCORRUPTED reporting.
* Fix a potential crash when disabling discard via remount followed
by an immediate unmount. (Found by Sashiko)
* Fix a corner case which could lead to allocating blocks for an
indirect-mapped inode block numbers > 2**32.
* Fix a race when reallocating a freed inode that could result in
a deadlock.
* Fix a user-after-free in update_super_work when racing with umount.
* Fix build issues when trying to build ext4's kunit tests as a module
* Fix a bug where ext4_split_extent_zeroout() could fail to pass
back an error from ext4_ext_dirty().
* Avoid allocating blocks from a corrupted block group in
ext4_mb_find_by_goal().
* Fix a percpu_counters list corruption BUG triggered by an
ext4 extents kunit.
* Fix a potetial crash caused by the fast commit flush path potentially
accessing the jinode structure before it is fully initialized.
* Fix fsync(2) in no-journal mode to make sure the dirtied inode is
write to storage.
* Fix a bug when in no-journal mode, when ext4 tries to avoid using
recently deleted inodes, if lazy itable initialization is enabled,
can lead to an unitialized inode getting skipped and triggering
an e2fsck complaint.
* Fix journal credit calculation when setting an xattr when both
the encryption and ea_inode feeatures are enabled.
* Fix corner cases which could result in stale xarray tags after
writeback.
* Fix generic/475 failures caused by ENOSPC errors while creating
a symlink when the system crashes resulting to a file system
inconsistency when replaying the fast commit journal.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEK2m5VNv+CHkogTfJ8vlZVpUNgaMFAmnIo3cACgkQ8vlZVpUN
gaNu+wf+PyZyRFar37GVcXiMWm8wiBrH7XYhcH1z+uEfjxtWuxUDtKZtF/UZ8FiW
peRI785hiIW1xjj3efkNlrg4JFPlY+mLlyY8iUabYj6Gt2kddgy7h6gCf2ugM/V9
1fk9Hf3+QQ38qM9PpBpBVZyhSS7WpafCcUvx622G/+WiQldWAohpfk/KrNQtSWiX
ZFzJtJ+7jJD6Qo1Pe2Em4khsZK2fsLw1XH9GpUWIdauQV+oXnkp7+kOQIOoT+7RX
azjAub5b6L3Bf9p/NNvlUCE9VINeqjKHVGI/gesRz9uiQd/zI3/pBQtddMUy8B3k
buN3uii5iYcLQD8ntX5sTP35PQg4hg==
=Ew20
-----END PGP SIGNATURE-----
Merge tag 'ext4_for_linus-7.0-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull ext4 fixes from Ted Ts'o:
- Update the MAINTAINERS file to add reviewers for the ext4 file system
- Add a test issue an ext4 warning (not a WARN_ON) if there are still
dirty pages attached to an evicted inode.
- Fix a number of Syzkaller issues
- Fix memory leaks on error paths
- Replace some BUG and WARN with EFSCORRUPTED reporting
- Fix a potential crash when disabling discard via remount followed by
an immediate unmount. (Found by Sashiko)
- Fix a corner case which could lead to allocating blocks for an
indirect-mapped inode block numbers > 2**32
- Fix a race when reallocating a freed inode that could result in a
deadlock
- Fix a user-after-free in update_super_work when racing with umount
- Fix build issues when trying to build ext4's kunit tests as a module
- Fix a bug where ext4_split_extent_zeroout() could fail to pass back
an error from ext4_ext_dirty()
- Avoid allocating blocks from a corrupted block group in
ext4_mb_find_by_goal()
- Fix a percpu_counters list corruption BUG triggered by an ext4
extents kunit
- Fix a potetial crash caused by the fast commit flush path potentially
accessing the jinode structure before it is fully initialized
- Fix fsync(2) in no-journal mode to make sure the dirtied inode is
write to storage
- Fix a bug when in no-journal mode, when ext4 tries to avoid using
recently deleted inodes, if lazy itable initialization is enabled,
can lead to an unitialized inode getting skipped and triggering an
e2fsck complaint
- Fix journal credit calculation when setting an xattr when both the
encryption and ea_inode feeatures are enabled
- Fix corner cases which could result in stale xarray tags after
writeback
- Fix generic/475 failures caused by ENOSPC errors while creating a
symlink when the system crashes resulting to a file system
inconsistency when replaying the fast commit journal
* tag 'ext4_for_linus-7.0-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4: (27 commits)
ext4: always drain queued discard work in ext4_mb_release()
ext4: handle wraparound when searching for blocks for indirect mapped blocks
ext4: skip split extent recovery on corruption
ext4: fix iloc.bh leak in ext4_fc_replay_inode() error paths
ext4: fix deadlock on inode reallocation
ext4: fix use-after-free in update_super_work when racing with umount
ext4: fix the might_sleep() warnings in kvfree()
ext4: reject mount if bigalloc with s_first_data_block != 0
ext4: fix extents-test.c is not compiled when EXT4_KUNIT_TESTS=M
ext4: fix mballoc-test.c is not compiled when EXT4_KUNIT_TESTS=M
ext4: introduce EXPORT_SYMBOL_FOR_EXT4_TEST() helper
jbd2: gracefully abort on checkpointing state corruptions
ext4: avoid infinite loops caused by residual data
ext4: validate p_idx bounds in ext4_ext_correct_indexes
ext4: test if inode's all dirty pages are submitted to disk
ext4: minor fix for ext4_split_extent_zeroout()
ext4: avoid allocate block from corrupted group in ext4_mb_find_by_goal()
ext4: kunit: extents-test: lix percpu_counters list corruption
ext4: publish jinode after initialization
ext4: replace BUG_ON with proper error handling in ext4_read_inline_folio
...
The active_req field serves double duty as both the "is a TX in
flight" flag (NULL means idle) and the storage for the in-flight
message pointer. When a client sends NULL via mbox_send_message(),
active_req is set to NULL, which the framework misinterprets as
"no active request". This breaks the TX state machine by:
- tx_tick() short-circuits on (!mssg), skipping the tx_done
callback and the tx_complete completion
- txdone_hrtimer() skips the channel entirely since active_req
is NULL, so poll-based TX-done detection never fires.
Fix this by introducing a MBOX_NO_MSG sentinel value that means
"no active request," freeing NULL to be valid message data. The
sentinel is defined in the subsystem-internal mailbox.h so that
controller drivers within drivers/mailbox/ can reference it, but
it is not exposed to clients outside the subsystem.
Fifteen in-tree callers send NULL (doorbell-style IPCs on Qualcomm,
Tegra, TI, Xilinx, i.MX, SCMI, and PCC platforms). All were
audited for regression:
- Most already work around the bug via knows_txdone=true with a
manual mbox_client_txdone() call, making the framework's
tracking irrelevant. These are unaffected.
- Poll-based callers (Xilinx zynqmp/r5) are strictly better off:
the poll timer now correctly detects NULL-active channels
instead of silently skipping them.
- irq-qcom-mpm.c was a pre-existing bug -- the only Qualcomm
caller that omitted the knows_txdone + mbox_client_txdone()
pattern. Fixed in a companion commit ("irqchip/qcom-mpm: Fix
missing mailbox TX done acknowledgment").
- No caller sets both a tx_done callback and sends NULL, nor
combines tx_block=true with NULL sends, so the newly reachable
callback/completion paths are never exercised.
Also update tegra-hsp's flush callback, which directly inspects
active_req to wait for the channel to drain: the old "!= NULL"
check becomes "!= MBOX_NO_MSG", otherwise flush spins until
timeout since the sentinel is non-NULL.
The only tradeoff is that 'MBOX_NO_MSG' can not be used as a message
by clients.
Reported-by: Joonwon Kang <joonwonkang@google.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com>
Quite some controller drivers use the defines from the internal header
already. This prevents controller drivers outside the mailbox directory.
Move the defines to the public controller header to allow this again as
the defines are not strictly internal anyhow.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Sudeep Holla <sudeep.holla@kernel.org>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com>
"Request" is wrong, there is a separate function for requesting. This
functions binds, so describe this.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com>
Memory resources are optional but if the resource is empty
devm_platform_get_and_ioremap_resource() prints an error nonetheless.
Refactor the code to check the resources locally first and process them
only if they are present. The -EBUSY error message of ioremap_resource()
is still kept because it is correct. The comment which explains that a
plain ioremap() is tried as a workaround is turned into a info message.
So, a user will be informed about it, too.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com>
The core initializes the 'mbox' field exactly like this, so don't
duplicate it in the driver.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Tested-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com>
Fix CURR and END address calculation for inserting a cmdq task into the
task list by using cmdq_reg_shift_addr() for proper address converting.
This ensures both CURR and END addresses are set correctly when
enabling the thread.
Fixes: a195c7ccfb ("mailbox: mtk-cmdq: Refine DMA address handling for the command buffer")
Signed-off-by: Jason-JH Lin <jason-jh.lin@mediatek.com>
Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com>
The return value of mtk_vcp_mbox_xlate() is checked by IS_ERR(), so
return NULL is incorrect and could lead to a NULL pointer dereference.
Fixes: b562abd956 ("mailbox: mediatek: Add mtk-vcp-mailbox driver")
Signed-off-by: Felix Gu <ustc.gu@gmail.com>
Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com>
Reduce allocations to a single one by using a flexible array member.
Allows using __counted_by for extra runtime analysis.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com>
Enable DP83TG720 PHY driver as a module to support TI's DP83TG720
1000BASE-T1 Automotive Ethernet PHY. This is required for the
DP83TG720-IND-SPE-EVM daughter card used with AM642 EVM ICSSG0
interface.
Signed-off-by: Meghana Malladi <m-malladi@ti.com>
Link: https://patch.msgid.link/20260323090358.632329-3-m-malladi@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Note that this pull is in addition to the 2nd set of such fixes that are
waiting to be picked up. Absolutely fine to queue these for the merge
window if that makes more sense.
Usual mixed back of ancient issues surfacing and newer problems.
adi,ad57770r
- Stop eating an error in read_raw.
adi,adxl313
- Check return of regmap_write() instead of ignoring it in one place.
adi,adxl355
- Fix the description of the temperature channel to be unsigned rather
than signed.
bosch,bmi160
- Avoid use of uninitialized data.
- Fix validation of small reference voltages.
hid-sensor-rotation:
- The timestamp location in this driver has unfortunately been broken for
a long time. Given it was correct for 6 years and then broken for the
next 6 years, use a one off hack to duplicate it in both locations.
The issue was as a result of the unique nature of quaternion
representation combined with large precision resulting in an
128 bit aligned channel.
nxp,sar-adc
- Avoid leaking a dma channel.
rfdigital,rfd77402
- Close a race between reinit_completion() and the irq happening.
ti,adc161s626
- Fix up buffer handling on big endian hosts which was broken due to
casting of pointers to different sized integers.
- Ensure a DMA safe buffer is used.
vishay,vcnl4035
- Fix up buffer handling on big endian hosts which was broken due to
casting of pointers to different sized integers.
vishay,veml6070
- Fix return value mess up that occurred when doing a guard() conversion.
-----BEGIN PGP SIGNATURE-----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=AXzp
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-7.0c' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/jic23/iio into char-misc-linus
Jonathan writes:
IIO: 3rd set of fixes for the 7.0 cycle.
Note that this pull is in addition to the 2nd set of such fixes that are
waiting to be picked up. Absolutely fine to queue these for the merge
window if that makes more sense.
Usual mixed back of ancient issues surfacing and newer problems.
adi,ad57770r
- Stop eating an error in read_raw.
adi,adxl313
- Check return of regmap_write() instead of ignoring it in one place.
adi,adxl355
- Fix the description of the temperature channel to be unsigned rather
than signed.
bosch,bmi160
- Avoid use of uninitialized data.
- Fix validation of small reference voltages.
hid-sensor-rotation:
- The timestamp location in this driver has unfortunately been broken for
a long time. Given it was correct for 6 years and then broken for the
next 6 years, use a one off hack to duplicate it in both locations.
The issue was as a result of the unique nature of quaternion
representation combined with large precision resulting in an
128 bit aligned channel.
nxp,sar-adc
- Avoid leaking a dma channel.
rfdigital,rfd77402
- Close a race between reinit_completion() and the irq happening.
ti,adc161s626
- Fix up buffer handling on big endian hosts which was broken due to
casting of pointers to different sized integers.
- Ensure a DMA safe buffer is used.
vishay,vcnl4035
- Fix up buffer handling on big endian hosts which was broken due to
casting of pointers to different sized integers.
vishay,veml6070
- Fix return value mess up that occurred when doing a guard() conversion.
* tag 'iio-fixes-for-7.0c' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/jic23/iio:
iio: light: veml6070: fix veml6070_read() return value
iio: adc: nxp-sar-adc: Fix DMA channel leak in trigger mode
iio: accel: adxl313: add missing error check in predisable
iio: dac: ad5770r: fix error return in ad5770r_read_raw()
iio: accel: fix ADXL355 temperature signature value
iio: light: vcnl4035: fix scan buffer on big-endian
iio: adc: ti-adc161s626: use DMA-safe memory for spi_read()
iio: adc: ti-adc161s626: fix buffer read on big-endian
iio: dac: mcp47feb02: Fix Vref validation [1-999] case
iio: imu: bmi160: Remove potential undefined behavior in bmi160_config_pin()
iio: orientation: hid-sensor-rotation: add timestamp hack to not break userspace
iio: proximity: rfd77402: Fix completion race condition in IRQ mode
Add support for timer by reusing existing sun4i timer driver.
H616 timer is compatible with earlier sunxi timer variants and provides
both clocksource and clockevent functionality. It runs from 24 MHz
oscillator. It can serve as broadcast clockevent for wake up from idle
states.
Tested on Orange Pi Zero 3:
- timer is registered as clocksource:
- switching clocksource at runtime works
- timer operates as a broadcast clockevent device
- no regression observed compared to arch_sys_counter
Signed-off-by: Michal Piekos <michal.piekos@mmpsystems.pl>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://patch.msgid.link/20260329-h616-timer-v1-1-5966d0420a66@mmpsystems.pl
Signed-off-by: Chen-Yu Tsai <wens@kernel.org>
All the UARTs support DMA and are hooked up to the DMA controller.
Add the DMA channels for the UARTs
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://patch.msgid.link/20260324161930.1602083-2-wens@kernel.org
Signed-off-by: Chen-Yu Tsai <wens@kernel.org>
All the UARTs support DMA and are hooked up to the DMA controller.
Add the DMA channels for the UARTs
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://patch.msgid.link/20260324161930.1602083-1-wens@kernel.org
Signed-off-by: Chen-Yu Tsai <wens@kernel.org>
Usual mixed bag of fixes for recent code and much older issues that have
surfaced. Biggest group are continued resolution of IRQF_ONE_SHOT
being used incorrectly (which now triggers a warning)
adi,ad4062
- Replace IRQF_ONESHOT (as no threaded handler) with IRQF_NO_THREAD as
the caller makes use of iio_trigger_poll() which cannot run from a
thread.
adi,ade9000
- Move mutex_init() earlier to ensure it is available if spurious IRQ
occurs.
adi,adis16550
- Fix swapped gyro and accel filter functions.
adi,adxl3380
- Fix some bit manipulation that was always resulting in 0.
- Fix incorrect register map for calibbias on the active power channel.
- Fix returning IRQF_HANDLED from a function that should return 0 or
-ERRNO.
aspeed,adc
- Clear a reference voltage bit that might be set prior to driver load.
bosch,bno055
- Off by one channel buffer sizing. Benine due to padding prior to the
subsequent timestamp.
hid-sensors
- A more complex fix to IRQF_ONESHOT warning as this driver had a trigger
that was never actually used but the ABI that exposed had to be
maintained to avoid regressions.
hid-sensors-rotation
- An obscure buffer alignment case that applies to quaternions only was
recently broken resulting in writes beyond the end of the channel buffer.
Add a new core macro and apply it in this driver to make it very clear
what was going on.
honeywell,abp2030pa
- Remove meaningless IRQF_ONESHOT from a non threaded IRQ handler.
Warning fix only.
invense,mpu3050
- Fix token passed to free_irq() to match the one used at setup.
- Fix an irq resource leak in error path.
- Reorder probe so that userspace interfaces are exposed only after
everything else has finished.
- Reorder remove slightly to cleanup the buffer only after irq removed
ensuring reverse of probe sequence.
microchip,mcp47feb02
- Fix use of mutex before it was initialized by not performing unnecessary
lock that was early enough in probe that all code was serial.
st,lsm6dsx
- Ensure that FIFO ODR is only controllable for accel and gyro channels
avoiding incorrect register accesses.
- Restrict separation of buffer sampling from main sampling rate to
accelerometer. It is only useful for running event detection faster
than the fifo and the only events are on the accelerometer.
ti,ads1018
- Fix overflow of u8 which wasn't big enough to store max data rate value.
ti,ads1119:
- Fix unbalanced pm in an error path.
- IRQF_ONESHOT (as no threaded handler) replaced with IRQF_NO_THREAD
(needed for iio_trigger_poll()).
- Ensure complete reinitialized before reuse. Previously it would have
completed immediate after the first time.
ti,ads7950
- Fix return value of gpio_get() to be 0 or 1.
- Avoid accidental overwrite of state resulting in gpio_get() only
returning 0 or -ERRNO but never 1.
-----BEGIN PGP SIGNATURE-----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=JTTZ
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-7.0b' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/jic23/iio into char-misc-linux
Jonathan writes:
IIO: 2nd set of fixes for the 7.0 cycle
Usual mixed bag of fixes for recent code and much older issues that have
surfaced. Biggest group are continued resolution of IRQF_ONE_SHOT
being used incorrectly (which now triggers a warning)
adi,ad4062
- Replace IRQF_ONESHOT (as no threaded handler) with IRQF_NO_THREAD as
the caller makes use of iio_trigger_poll() which cannot run from a
thread.
adi,ade9000
- Move mutex_init() earlier to ensure it is available if spurious IRQ
occurs.
adi,adis16550
- Fix swapped gyro and accel filter functions.
adi,adxl3380
- Fix some bit manipulation that was always resulting in 0.
- Fix incorrect register map for calibbias on the active power channel.
- Fix returning IRQF_HANDLED from a function that should return 0 or
-ERRNO.
aspeed,adc
- Clear a reference voltage bit that might be set prior to driver load.
bosch,bno055
- Off by one channel buffer sizing. Benine due to padding prior to the
subsequent timestamp.
hid-sensors
- A more complex fix to IRQF_ONESHOT warning as this driver had a trigger
that was never actually used but the ABI that exposed had to be
maintained to avoid regressions.
hid-sensors-rotation
- An obscure buffer alignment case that applies to quaternions only was
recently broken resulting in writes beyond the end of the channel buffer.
Add a new core macro and apply it in this driver to make it very clear
what was going on.
honeywell,abp2030pa
- Remove meaningless IRQF_ONESHOT from a non threaded IRQ handler.
Warning fix only.
invense,mpu3050
- Fix token passed to free_irq() to match the one used at setup.
- Fix an irq resource leak in error path.
- Reorder probe so that userspace interfaces are exposed only after
everything else has finished.
- Reorder remove slightly to cleanup the buffer only after irq removed
ensuring reverse of probe sequence.
microchip,mcp47feb02
- Fix use of mutex before it was initialized by not performing unnecessary
lock that was early enough in probe that all code was serial.
st,lsm6dsx
- Ensure that FIFO ODR is only controllable for accel and gyro channels
avoiding incorrect register accesses.
- Restrict separation of buffer sampling from main sampling rate to
accelerometer. It is only useful for running event detection faster
than the fifo and the only events are on the accelerometer.
ti,ads1018
- Fix overflow of u8 which wasn't big enough to store max data rate value.
ti,ads1119:
- Fix unbalanced pm in an error path.
- IRQF_ONESHOT (as no threaded handler) replaced with IRQF_NO_THREAD
(needed for iio_trigger_poll()).
- Ensure complete reinitialized before reuse. Previously it would have
completed immediate after the first time.
ti,ads7950
- Fix return value of gpio_get() to be 0 or 1.
- Avoid accidental overwrite of state resulting in gpio_get() only
returning 0 or -ERRNO but never 1.
* tag 'iio-fixes-for-7.0b' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (25 commits)
iio: imu: adis16550: fix swapped gyro/accel filter functions
iio: adc: aspeed: clear reference voltage bits before configuring vref
iio: adc: ti-ads1119: Reinit completion before wait_for_completion_timeout()
iio: adc: ti-ads1018: fix type overflow for data rate
iio: adc: ti-ads7950: do not clobber gpio state in ti_ads7950_get()
iio: adc: ti-ads7950: normalize return value of gpio_get
iio: orientation: hid-sensor-rotation: fix quaternion alignment
iio: add IIO_DECLARE_QUATERNION() macro
iio: adc: ti-ads1119: Replace IRQF_ONESHOT with IRQF_NO_THREAD
iio: imu: bno055: fix BNO055_SCAN_CH_COUNT off by one
iio: hid-sensors: Use software trigger
iio: adc: ad4062: Replace IRQF_ONESHOT with IRQF_NO_THREAD
iio: gyro: mpu3050: Fix out-of-sequence free_irq()
iio: gyro: mpu3050: Move iio_device_register() to correct location
iio: gyro: mpu3050: Fix irq resource leak
iio: gyro: mpu3050: Fix incorrect free_irq() variable
iio: imu: st_lsm6dsx: Set buffer sampling frequency for accelerometer only
iio: imu: st_lsm6dsx: Set FIFO ODR for accelerometer and gyroscope only
iio: dac: mcp47feb02: Fix mutex used before initialization
iio: adc: ade9000: fix wrong return type in streaming push
...
This contains one driver fix for the current cycle.
- interconnect: qcom: sm8450: Fix NULL pointer dereference in icc_link_nodes()
Signed-off-by: Georgi Djakov <djakov@kernel.org>
-----BEGIN PGP SIGNATURE-----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=3arT
-----END PGP SIGNATURE-----
Merge tag 'icc-7.0-rc6' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/djakov/icc into char-misc-linus
interconnect fix for v7.0-rc
This contains one driver fix for the current cycle.
- interconnect: qcom: sm8450: Fix NULL pointer dereference in icc_link_nodes()
Signed-off-by: Georgi Djakov <djakov@kernel.org>
* tag 'icc-7.0-rc6' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/djakov/icc:
interconnect: qcom: sm8450: Fix NULL pointer dereference in icc_link_nodes()
Includes merge of v7.0-rc4 to pull in a fix and a merge of
ib-iio-thermal-qcom-pmic5 immutable branch (provided from the IIO tree so
thermal could also pick this up and add thermal specific remainder
of the series on top.
New device support
------------------
adi,ad4030
- Add support for ADA4316 and ADAQ4224 ADCs with PGAs.
adi,ad4080
- Add support for AD4082, AD4085 and AD4088 ADCs.
adi,ad8366
- Add ADRF5702 and ADRF5703 digital step attenuators.
adi,adxl372
- Add support for the ADXL371 accelerometer after refactors to allow multiple
device variants to be supported by the driver. In particular a silicon
issue means the hardware FIFO doesn't work on the ADXL371
bosch,bma255/bmg160
- Add support for BMX055 gyroscope and magnetometer (effectively separate
devices from point of view of interface).
lltc,ltc2309
- Add support for LTC2305 2 channel 12-bit ADC.
lltc,ltc2532
- Add support for 4 variants of the LTC2654 quad DAC.
maxim,ds4424
- Add IDs for DS4402 and DS4404 parts. Initially patch is ID only but additional
features also added that are device dependent.
qcom,spmi-adc-gen3
- New driver supporting this generation of Qualcomm's SoC ADC.
st,vl53l1
- New driver for this Time Of Flight (TOF) sensor.
ti,ina2xx
- Support the INA236 digital power monitor.
vishay,vcnl4000
- Add support for CM36686 ambient light and proximity sensor.
- Add support for CM36672P proximity sensors.
ID only additions.
amlogic,meson-adc
- Support the Meson S4.
Features
--------
iio-backend framework
- Add capability discovery so front end drivers can know what features are
available from the backend and adjust how they operate.
adi,ad4030
- Add SPI offload support requiring a non trivial PWM setup.
adi,ad7380
- Add support for multiple SPI lanes to improve throughput.
adi,ad7768-1
- Support SPI offload and always use continuous mode, enabling more
filter options.
adi,ad8366
- Device tree bindings and support.
aspeed,adc
- Handle battery channel.
maxim,ds4424
- Add external resistor controlled scale and per-variant limits.
- Handle per variant range limits.
- Move it to regmap.
motorola,cpcap-adc
- Support for the ADC found on the Motorola Mot board. Effectively some board
specific configuration handled in the driver.
vishay,vcnl4000
- Support explicit power supply regulators.
tyhx,hx9023s
- Allow device tree specification of firmware file name.
Cleanup and minor fixes
-----------------------
treewide
- Remove a bunch of unused structure elements.
- Replaces standard fixed width integers with kernel types.
- Replace some other error values that were returned on allocation failure
with -ENOMEM
iio-core
- Replace a few custom devm implementations for devm_add_action_or_reset()
iio-trigger
- Use put_device() to cleanup on error.
iio-backend
- Use __free(fwmode_handle) to simplify some code.
hw-consumer
- Use separate allocation for scan mask bitmap to simplify code.
acpi-als
- Switch from ACPI driver to platform driver.
adi,ad4030
- Use BIT() to replace values that are always a power of 2 to slightly
improve readability.
adi,ad4062
- Add a missing check for error form iio_get_current_scan_type()
adi,ad5933
- Use div64_ul() rather than do_div() as remainder was not used.
adi,ad7191
- Documentation fixes related to clocks
adi,ad7816
- Use sysfs_emit()
adi,ad8366
- General driver modernization
adi,adf4350
- Change a TOOD to NOTE in a comment to avoid anyone from walking into
a tricky to improve corner case.
adi,admv1013
- Avoid a null pointer dereference if device_property_read_string() fails.
adi,admv4420
- Return error code rather than -1..
adi,adxl345
- Add separate scaling for events from that of raw channels.
amlogic,meson-adc
- Don't bother keeping nvmem cell access around when only used in probe.
atmel,at91-sama5d
- Don't bother keeping nvmem cell access around when only used in probe.
bosch,bmc150
- Use sysfs_emit() in a few places.
honeywell,hsc030pa
- Improve handling of return values from i2c_transfer.
liteon,ltr501
- Return error values rather than -1 replaced by -EINVAL at higher
levels of the callstack.
maxim,ds4424
- A bunch of general minor improvements prior to adding new features.
maxim,max11410
- Make some const string arrays static.
maxim,max5522
- Use devm_regulator_get_enable_read_voltage() at probe to cache the
voltage rather than keeping the regulator around to access and query
later.
vishay,vcnl4000
- Various code improvements.
sharp,gp2ap020a00f
- General driver modernization.
silabs,si7210
- Use devm_regulator_get_enable_read_voltage() at probe to cache the
voltage rather than keeping the regulator around to access and query
later.
st,lsm6dsx
- Add SMOCF00 ACPI ID seen on products by SHIFT.
st,st_sensors
- Fix up various kernel-doc issues.
- Avoid kmalloc of a single use buffer and instead reused existing
buffer_data.
taos,tsl2772
- Fix some kernel-doc warnings due to missing :
ti,ads7950
- Use iio_push_to_buffers_with_ts_unaligned() as first few elements of
array are not the data that is pushed.
- Move from array of chip_info structures to individual named ones. This
is part of slowly replacing use of a code pattern that we don't want
replicated in new drivers.
vti,sca3000
- General driver modernization included use of devm and guard().
Various other more minor stuff not called out explicitly.
Includes things like typo fixes, use of dev_err_probe() and local
variables to avoid repeated dereferencing of the same member as well as
increasing use of guard() to simplify release of locks.
Another slow improvement to code quality is both standardizing on
header order and ensure all appropriate headers are included.
-----BEGIN PGP SIGNATURE-----
iQJFBAABCgAvFiEEbilms4eEBlKRJoGxVIU0mcT0FogFAmnINKERHGppYzIzQGtl
cm5lbC5vcmcACgkQVIU0mcT0FognJg//a2J1qP+D8gf3nfBdrTyLaS7DCQZib60V
0wHrSewlT49fM2P1A4Y//cNV+wekb84EAmZLduxaRLkgHC8ZAeGxWy6DY2q0SFww
AN20+6toP3M1J7eIRW7ENB7aqwAczu/SzU+6fGcwxGicbjorDE1iQHiR38eXuKqi
l8kjV4YO4PICHkQWU7D0y2D7Nvp/BgBwDmtRzzfVdtIMYcyaOH5fvDFByfaQiTW6
rftwvzFH3lgV2pMOMUDwa0e071DQhMLxjleFwAW5jbvMqXf/15379tVXhFA6BhMi
T1wlB10w1xl0QBbmYJrDOIpaFT4BdET+pQyrlB74sDrVbFF2ip8a1e4ux0fCPZIZ
qmBAjzTTtE36PFWVdak8PCasEuyKGEpsSMfSOpmZZEaXFTAjKISuKLZrCuHgmkIl
BY+Vswq5trkLF3GLLc8me+4L3hG4ujx40OZEk42G2B10kAJXyvG5bHGeJ0Jy/B3O
CaMweZJeDBloZyXwrgNx5n+wIeKm7g6SqcL+85XMSN9x+jh4FcBDoHTFXAq5kqlv
u4hWg2fjoyu+O/CRHRBLIfg5CBd+8oNlf8kbSa1wx1VY4IHSO9z5Xj/se+VSTew3
haCR/wvVG4Rs33krGyYnjMhoOGOnFZkiHoI85ATqsb+ZRzZdFWG+5mb5wN5Hgt5V
I6KAnuZNsrI=
=/WQe
-----END PGP SIGNATURE-----
Merge tag 'iio-for-7.1a' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/jic23/iio into char-misc-next
Jonathan writes:
IIO: New devices support, features and cleanup for 7.1
Includes merge of v7.0-rc4 to pull in a fix and a merge of
ib-iio-thermal-qcom-pmic5 immutable branch (provided from the IIO tree so
thermal could also pick this up and add thermal specific remainder
of the series on top.
New device support
------------------
adi,ad4030
- Add support for ADA4316 and ADAQ4224 ADCs with PGAs.
adi,ad4080
- Add support for AD4082, AD4085 and AD4088 ADCs.
adi,ad8366
- Add ADRF5702 and ADRF5703 digital step attenuators.
adi,adxl372
- Add support for the ADXL371 accelerometer after refactors to allow multiple
device variants to be supported by the driver. In particular a silicon
issue means the hardware FIFO doesn't work on the ADXL371
bosch,bma255/bmg160
- Add support for BMX055 gyroscope and magnetometer (effectively separate
devices from point of view of interface).
lltc,ltc2309
- Add support for LTC2305 2 channel 12-bit ADC.
lltc,ltc2532
- Add support for 4 variants of the LTC2654 quad DAC.
maxim,ds4424
- Add IDs for DS4402 and DS4404 parts. Initially patch is ID only but additional
features also added that are device dependent.
qcom,spmi-adc-gen3
- New driver supporting this generation of Qualcomm's SoC ADC.
st,vl53l1
- New driver for this Time Of Flight (TOF) sensor.
ti,ina2xx
- Support the INA236 digital power monitor.
vishay,vcnl4000
- Add support for CM36686 ambient light and proximity sensor.
- Add support for CM36672P proximity sensors.
ID only additions.
amlogic,meson-adc
- Support the Meson S4.
Features
--------
iio-backend framework
- Add capability discovery so front end drivers can know what features are
available from the backend and adjust how they operate.
adi,ad4030
- Add SPI offload support requiring a non trivial PWM setup.
adi,ad7380
- Add support for multiple SPI lanes to improve throughput.
adi,ad7768-1
- Support SPI offload and always use continuous mode, enabling more
filter options.
adi,ad8366
- Device tree bindings and support.
aspeed,adc
- Handle battery channel.
maxim,ds4424
- Add external resistor controlled scale and per-variant limits.
- Handle per variant range limits.
- Move it to regmap.
motorola,cpcap-adc
- Support for the ADC found on the Motorola Mot board. Effectively some board
specific configuration handled in the driver.
vishay,vcnl4000
- Support explicit power supply regulators.
tyhx,hx9023s
- Allow device tree specification of firmware file name.
Cleanup and minor fixes
-----------------------
treewide
- Remove a bunch of unused structure elements.
- Replaces standard fixed width integers with kernel types.
- Replace some other error values that were returned on allocation failure
with -ENOMEM
iio-core
- Replace a few custom devm implementations for devm_add_action_or_reset()
iio-trigger
- Use put_device() to cleanup on error.
iio-backend
- Use __free(fwmode_handle) to simplify some code.
hw-consumer
- Use separate allocation for scan mask bitmap to simplify code.
acpi-als
- Switch from ACPI driver to platform driver.
adi,ad4030
- Use BIT() to replace values that are always a power of 2 to slightly
improve readability.
adi,ad4062
- Add a missing check for error form iio_get_current_scan_type()
adi,ad5933
- Use div64_ul() rather than do_div() as remainder was not used.
adi,ad7191
- Documentation fixes related to clocks
adi,ad7816
- Use sysfs_emit()
adi,ad8366
- General driver modernization
adi,adf4350
- Change a TOOD to NOTE in a comment to avoid anyone from walking into
a tricky to improve corner case.
adi,admv1013
- Avoid a null pointer dereference if device_property_read_string() fails.
adi,admv4420
- Return error code rather than -1..
adi,adxl345
- Add separate scaling for events from that of raw channels.
amlogic,meson-adc
- Don't bother keeping nvmem cell access around when only used in probe.
atmel,at91-sama5d
- Don't bother keeping nvmem cell access around when only used in probe.
bosch,bmc150
- Use sysfs_emit() in a few places.
honeywell,hsc030pa
- Improve handling of return values from i2c_transfer.
liteon,ltr501
- Return error values rather than -1 replaced by -EINVAL at higher
levels of the callstack.
maxim,ds4424
- A bunch of general minor improvements prior to adding new features.
maxim,max11410
- Make some const string arrays static.
maxim,max5522
- Use devm_regulator_get_enable_read_voltage() at probe to cache the
voltage rather than keeping the regulator around to access and query
later.
vishay,vcnl4000
- Various code improvements.
sharp,gp2ap020a00f
- General driver modernization.
silabs,si7210
- Use devm_regulator_get_enable_read_voltage() at probe to cache the
voltage rather than keeping the regulator around to access and query
later.
st,lsm6dsx
- Add SMOCF00 ACPI ID seen on products by SHIFT.
st,st_sensors
- Fix up various kernel-doc issues.
- Avoid kmalloc of a single use buffer and instead reused existing
buffer_data.
taos,tsl2772
- Fix some kernel-doc warnings due to missing :
ti,ads7950
- Use iio_push_to_buffers_with_ts_unaligned() as first few elements of
array are not the data that is pushed.
- Move from array of chip_info structures to individual named ones. This
is part of slowly replacing use of a code pattern that we don't want
replicated in new drivers.
vti,sca3000
- General driver modernization included use of devm and guard().
Various other more minor stuff not called out explicitly.
Includes things like typo fixes, use of dev_err_probe() and local
variables to avoid repeated dereferencing of the same member as well as
increasing use of guard() to simplify release of locks.
Another slow improvement to code quality is both standardizing on
header order and ensure all appropriate headers are included.
* tag 'iio-for-7.1a' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (217 commits)
Docs: iio: ad7191 Correct clock configuration
iio: amplifiers: ad8366: add support for adrf5702/3
dt-bindings: iio: amplifiers: ad8366: add adrf5702/3 support
iio: adc: meson-saradc: add support for Meson S4
dt-bindings: iio: adc: amlogic,meson-saradc: add S4 compatible
iio: imu: st_lsm6dsx: Add ACPI ID for SHIFT13mi gyroscope
iio: proximity: add driver for ST VL53L1X ToF sensor
dt-bindings: iio: proximity: add ST VL53L1X ToF sensor
iio: adc: max11410: make vref register name arrays static const
iio: accel: bmc150-accel-core: use sysfs_emit() in show functions
iio: frequency: adf4350: replace TODO with NOTE in adf4350_set_freq()
iio: adc: ltc2309: add support for ltc2305
iio: adc: ltc2309: explicitly assign hex values to channel enums
dt-bindings: adc: ltc2497: add support for ltc2305
iio: accel: adxl380: fix typo in PART_ID register macro
iio: dac: ds4424: add Rfs-based scale and per-variant limits
dt-bindings: iio: dac: maxim,ds4424: add maxim,rfs-ohms property
iio: dac: ds4424: convert to regmap
iio: dac: ds4424: support per-variant output range limits
iio: dac: ds4424: add DS4402/DS4404 device IDs
...
Use the new snp_prepare() to initialize SNP from the ccp driver instead of at
boot time. This means that SNP is not enabled unless it is really going to be
used (i.e. kvm_amd loads the ccp driver automatically).
Signed-off-by: Tycho Andersen (AMD) <tycho@kernel.org>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Tom Lendacky <thomas.lendacky@amd.com>
Link: https://patch.msgid.link/20260324161301.1353976-5-tycho@kernel.org
After SNP_SHUTDOWN, two things should be done:
1. clear the RMP table
2. disable MFDM to prevent the FW_WARN in k8_check_syscfg_dram_mod_en() in
the event of a kexec
Create and export to the CCP driver a function that does them.
Also change the MFDM helper to allow for disabling the bit, since the SNP x86
shutdown path needs to disable MFDM.
The comment for k8_check_syscfg_dram_mod_en() notes, the "BIOS" is supposed
clear it, or the kernel in the case of module unload and shutdown followed by
kexec.
Signed-off-by: Tycho Andersen (AMD) <tycho@kernel.org>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Tom Lendacky <thomas.lendacky@amd.com>
Link: https://patch.msgid.link/20260324161301.1353976-4-tycho@kernel.org
Commit ab949d5196 ("ALSA: hda - Fix deadlock of controller device
lock at unbinding") added a temporary device_unlock()/device_lock()
pair around probe-work cancellation to avoid a deadlock between
controller unbind and codec probe.
That deadlock depended on the driver core taking both a device lock and
its parent lock during bind and unbind. Since commit 8c97a46af0
("driver core: hold dev's parent lock when needed") and follow-up
fixes, the parent lock is only taken when bus->need_parent_lock is set.
The HDA bus does not set that flag, so codec binding no longer locks
the controller device as the codec's parent.
Keep cancel_delayed_work_sync(), since the async probe/remove race
still needs to be serialized, but drop the stale unlock/relock
workaround and its outdated FIXME comment. Keeping it around only
opens an unnecessary unlocked window inside azx_remove().
Signed-off-by: Cássio Gabriel <cassiogabrielcontato@gmail.com>
Link: https://patch.msgid.link/20260328-hda-intel-drop-obsolete-probe-workaround-v1-1-bc43aeafc98b@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use macros to make the AF16Rig quirk table smaller.
Add a disabled block containing the theoretical quirks for the other
clock sources that the AF16Rig has. It's disabled because I cannot test
it.
Fixes: 0da18c2dd1 ("ALSA: usb-audio: Add quirks for Arturia AF16Rig")
Tested-By: Phil Willoughby <willerz@gmail.com>
Signed-off-by: Phil Willoughby <willerz@gmail.com>
Link: https://patch.msgid.link/20260328160326.23665-1-willerz@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
