rtl8xxxu_gen2_config_channel() was missing the subchannel setting.
This function is used by RTL8192EU and RTL8723BU.
This change seems to make no difference in my testing on channel 13
with either chip.
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/a5de8d39-45c1-4667-ab4c-7109de6eb13d@gmail.com
Set the required fields in the TX descriptor to allow these chips to
transmit with 40 MHz channel width when the access point supports it.
Tested only with RTL8192CU, but these settings are identical for
RTL8723AU.
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/30d95228-69b2-48f9-8854-c98d2408c4d3@gmail.com
Flip the response rate subchannel. It was backwards, causing low
speeds when using 40 MHz channel width. "iw dev ... station dump"
showed a low RX rate, 11M or less.
Also fix the channel width field of RF6052_REG_MODE_AG.
Tested only with RTL8192CU, but these settings are identical for
RTL8723AU.
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/1f46571d-855b-43e1-8bfc-abacceb96043@gmail.com
We can allocate high-order pages, but mapping them one by
one is inefficient. This patch changes the code to map
as large a chunk as possible. The code looks somewhat
complicated mainly because supporting mmap with a
non-zero offset is a bit tricky.
Using the micro-benchmark below, we see that mmap becomes
35X faster:
#include <stdio.h>
#include <fcntl.h>
#include <linux/dma-heap.h>
#include <sys/ioctl.h>
#include <sys/mman.h>
#include <time.h>
#include <unistd.h>
#include <stdlib.h>
#define SIZE (512UL * 1024 * 1024)
#define PAGE 4096
#define STRIDE (PAGE/sizeof(int))
#define PAGES (SIZE/PAGE)
int main(void) {
int heap = open("/dev/dma_heap/system", O_RDONLY);
struct dma_heap_allocation_data d =
{ .len = SIZE, .fd_flags = O_RDWR|O_CLOEXEC };
ioctl(heap, DMA_HEAP_IOCTL_ALLOC, &d);
struct timespec t0, t1;
clock_gettime(CLOCK_MONOTONIC, &t0);
int *p = mmap(NULL, SIZE, PROT_READ|PROT_WRITE, MAP_SHARED, d.fd, 0);
clock_gettime(CLOCK_MONOTONIC, &t1);
for (int i = 0; i < PAGES; i++) p[i*STRIDE] = i;
for (int i = 0; i < PAGES; i++)
if (p[i*STRIDE] != i) {
fprintf(stderr, "mismatch at page %d\n", i);
exit(1);
}
long ns = (t1.tv_sec-t0.tv_sec)*1000000000L +
(t1.tv_nsec-t0.tv_nsec);
printf("mmap 512MB took %.3f us, verify OK\n", ns/1000.0);
return 0;
}
W/ patch:
~ # ./a.out
mmap 512MB took 200266.000 us, verify OK
~ # ./a.out
mmap 512MB took 198151.000 us, verify OK
~ # ./a.out
mmap 512MB took 197069.000 us, verify OK
~ # ./a.out
mmap 512MB took 196781.000 us, verify OK
~ # ./a.out
mmap 512MB took 198102.000 us, verify OK
~ # ./a.out
mmap 512MB took 195552.000 us, verify OK
W/o patch:
~ # ./a.out
mmap 512MB took 6987470.000 us, verify OK
~ # ./a.out
mmap 512MB took 6970739.000 us, verify OK
~ # ./a.out
mmap 512MB took 6984383.000 us, verify OK
~ # ./a.out
mmap 512MB took 6971311.000 us, verify OK
~ # ./a.out
mmap 512MB took 6991680.000 us, verify OK
Signed-off-by: Barry Song <v-songbaohua@oppo.com>
Acked-by: John Stultz <jstultz@google.com>
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
[sumits: correct from 3.5x to 35x]
Link: https://patch.msgid.link/20251021042022.47919-1-21cnbao@gmail.com
If CONFIG_OF is not enabled, of_match_node() is set as NULL and
qcom_cpufreq_ipq806x_match_list won't be used causing a compilation
warning.
Flag qcom_cpufreq_ipq806x_match_list as __maybe_unused to fix the
compilation warning.
While at it also flag as __initconst as it's used only in probe contest
and can be freed after probe.
This follows the pattern of the usual of_device_id variables.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202511202119.6zvvFMup-lkp@intel.com/
Fixes: 58f5d39d5e ("cpufreq: qcom-nvmem: add compatible fallback for ipq806x for no SMEM")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
[ Viresh: Drop __initconst ]
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Call vfio_pci_core_fill_phys_vec() with the proper physical ranges for the
synthetic BAR 2 and BAR 4 regions. Otherwise use the normal flow based on
the PCI bar.
This demonstrates a DMABUF that follows the region info report to only
allow mapping parts of the region that are mmapable. Since the BAR is
power of two sized and the "CXL" region is just page aligned the there can
be a padding region at the end that is not mmaped or passed into the
DMABUF.
The "CXL" ranges that are remapped into BAR 2 and BAR 4 areas are not PCI
MMIO, they actually run over the CXL-like coherent interconnect and for
the purposes of DMA behave identically to DRAM. We don't try to model this
distinction between true PCI BAR memory that takes a real PCI path and the
"CXL" memory that takes a different path in the p2p framework for now.
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Tested-by: Alex Mastro <amastro@fb.com>
Tested-by: Nicolin Chen <nicolinc@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Acked-by: Ankit Agrawal <ankita@nvidia.com>
Reviewed-by: Ankit Agrawal <ankita@nvidia.com>
Link: https://lore.kernel.org/r/20251120-dmabuf-vfio-v9-11-d7f71607f371@nvidia.com
Signed-off-by: Alex Williamson <alex@shazbot.org>
Add support for exporting PCI device MMIO regions through dma-buf,
enabling safe sharing of non-struct page memory with controlled
lifetime management. This allows RDMA and other subsystems to import
dma-buf FDs and build them into memory regions for PCI P2P operations.
The implementation provides a revocable attachment mechanism using
dma-buf move operations. MMIO regions are normally pinned as BARs
don't change physical addresses, but access is revoked when the VFIO
device is closed or a PCI reset is issued. This ensures kernel
self-defense against potentially hostile userspace.
Currently VFIO can take MMIO regions from the device's BAR and map
them into a PFNMAP VMA with special PTEs. This mapping type ensures
the memory cannot be used with things like pin_user_pages(), hmm, and
so on. In practice only the user process CPU and KVM can safely make
use of these VMA. When VFIO shuts down these VMAs are cleaned by
unmap_mapping_range() to prevent any UAF of the MMIO beyond driver
unbind.
However, VFIO type 1 has an insecure behavior where it uses
follow_pfnmap_*() to fish a MMIO PFN out of a VMA and program it back
into the IOMMU. This has a long history of enabling P2P DMA inside
VMs, but has serious lifetime problems by allowing a UAF of the MMIO
after the VFIO driver has been unbound.
Introduce DMABUF as a new safe way to export a FD based handle for the
MMIO regions. This can be consumed by existing DMABUF importers like
RDMA or DRM without opening an UAF. A following series will add an
importer to iommufd to obsolete the type 1 code and allow safe
UAF-free MMIO P2P in VM cases.
DMABUF has a built in synchronous invalidation mechanism called
move_notify. VFIO keeps track of all drivers importing its MMIO and
can invoke a synchronous invalidation callback to tell the importing
drivers to DMA unmap and forget about the MMIO pfns. This process is
being called revoke. This synchronous invalidation fully prevents any
lifecycle problems. VFIO will do this before unbinding its driver
ensuring there is no UAF of the MMIO beyond the driver lifecycle.
Further, VFIO has additional behavior to block access to the MMIO
during things like Function Level Reset. This is because some poor
platforms may experience a MCE type crash when touching MMIO of a PCI
device that is undergoing a reset. Today this is done by using
unmap_mapping_range() on the VMAs. Extend that into the DMABUF world
and temporarily revoke the MMIO from the DMABUF importers during FLR
as well. This will more robustly prevent an errant P2P from possibly
upsetting the platform.
A DMABUF FD is a preferred handle for MMIO compared to using something
like a pgmap because:
- VFIO is supported, including its P2P feature, on archs that don't
support pgmap
- PCI devices have all sorts of BAR sizes, including ones smaller
than a section so a pgmap cannot always be created
- It is undesirable to waste a lot of memory for struct pages,
especially for a case like a GPU with ~100GB of BAR size
- We want a synchronous revoke semantic to support FLR with light
hardware requirements
Use the P2P subsystem to help generate the DMA mapping. This is a
significant upgrade over the abuse of dma_map_resource() that has
historically been used by DMABUF exporters. Experience with an OOT
version of this patch shows that real systems do need this. This
approach deals with all the P2P scenarios:
- Non-zero PCI bus_offset
- ACS flags routing traffic to the IOMMU
- ACS flags that bypass the IOMMU - though vfio noiommu is required
to hit this.
There will be further work to formalize the revoke semantic in
DMABUF. For now this acts like a move_notify dynamic exporter where
importer fault handling will get a failure when they attempt to map.
This means that only fully restartable fault capable importers can
import the VFIO DMABUFs. A future revoke semantic should open this up
to more HW as the HW only needs to invalidate, not handle restartable
faults.
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Vivek Kasireddy <vivek.kasireddy@intel.com>
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Acked-by: Ankit Agrawal <ankita@nvidia.com>
Link: https://lore.kernel.org/r/20251120-dmabuf-vfio-v9-10-d7f71607f371@nvidia.com
Signed-off-by: Alex Williamson <alex@shazbot.org>
Fix the following warning with W=1:
arch/arm64/boot/dts/ti/k3-am62l.dtsi:101.30-112.5: Warning (simple_bus_reg): /bus@f0000/bus@43000000: simple-bus unit address format error, expected "a80000"
While at that, also remove extra space b/w label and node name.
Fixes: 5f016758b0 ("arm64: dts: ti: k3-am62l: add initial infrastructure")
Link: https://patch.msgid.link/20251120143419.223238-1-vigneshr@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
The SoC pin Y1 is incorrectly defined in the WKUP Pinmux device-tree node
(pinctrl@4301c000) leading to the following silent failure:
pinctrl-single 4301c000.pinctrl: mux offset out of range: 0x1dc (0x178)
According to the datasheet for the J721E SoC [0], the pin Y1 belongs to the
MAIN Pinmux device-tree node (pinctrl@11c000). This is confirmed by the
address of the pinmux register for it on page 142 of the datasheet which is
0x00011C1DC.
Hence fix it.
[0]: https://www.ti.com/lit/ds/symlink/tda4vm.pdf
Fixes: 97b67cc102 ("arm64: dts: ti: k3-j721e-sk: Add DT nodes for power regulators")
Cc: stable@vger.kernel.org
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Yemike Abhilash Chandra <y-abhilashchandra@ti.com>
Link: https://patch.msgid.link/20251119160148.2752616-1-s-vadapalli@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
It's a requirement that DT overlays be applied at build time in order to
validate them as overlays are not validated on their own.
Add the missing TI overlays. Some of the TI overlays have the first part
needed (a "*-dtbs" variable), but not the second part adding the target to
dtb-y/dtb- variable.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
[vigneshr@ti.com: create new target for J721e GESI EVM]
Link: https://patch.msgid.link/20251120141936.190796-1-vigneshr@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Currently if a user enqueues a work item using schedule_delayed_work() the
used wq is "system_wq" (per-cpu wq) while queue_delayed_work() use
WORK_CPU_UNBOUND (used when a cpu is not specified). The same applies to
schedule_work() that is using system_wq and queue_work(), that makes use
again of WORK_CPU_UNBOUND.
This lack of consistency cannot be addressed without refactoring the API.
For more details see the Link tag below.
alloc_workqueue() treats all queues as per-CPU by default, while unbound
workqueues must opt-in via WQ_UNBOUND.
This default is suboptimal: most workloads benefit from unbound queues,
allowing the scheduler to place worker threads where they’re needed and
reducing noise when CPUs are isolated.
This continues the effort to refactor workqueue APIs, which began with
the introduction of new workqueues and a new alloc_workqueue flag in:
commit 128ea9f6cc ("workqueue: Add system_percpu_wq and system_dfl_wq")
commit 930c2ea566 ("workqueue: Add new WQ_PERCPU flag")
This change adds the WQ_UNBOUND flag to explicitly request
alloc_workqueue() to be unbound, because this specific workload has no
benefit being per-cpu.
With the introduction of the WQ_PERCPU flag (equivalent to !WQ_UNBOUND),
any alloc_workqueue() caller that doesn’t explicitly specify WQ_UNBOUND
must now use WQ_PERCPU.
Once migration is complete, WQ_UNBOUND can be removed and unbound will
become the implicit default.
Suggested-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Marco Crivellari <marco.crivellari@suse.com>
Link: https://lore.kernel.org/all/20250221112003.1dSuoGyc@linutronix.de/
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20251118102032.54375-3-marco.crivellari@suse.com
Currently if a user enqueues a work item using schedule_delayed_work() the
used wq is "system_wq" (per-cpu wq) while queue_delayed_work() use
WORK_CPU_UNBOUND (used when a cpu is not specified). The same applies to
schedule_work() that is using system_wq and queue_work(), that makes use
again of WORK_CPU_UNBOUND.
This lack of consistency cannot be addressed without refactoring the API.
For more details see the Link tag below.
alloc_workqueue() treats all queues as per-CPU by default, while unbound
workqueues must opt-in via WQ_UNBOUND.
This default is suboptimal: most workloads benefit from unbound queues,
allowing the scheduler to place worker threads where they’re needed and
reducing noise when CPUs are isolated.
This continues the effort to refactor workqueue APIs, which began with
the introduction of new workqueues and a new alloc_workqueue flag in:
commit 128ea9f6cc ("workqueue: Add system_percpu_wq and system_dfl_wq")
commit 930c2ea566 ("workqueue: Add new WQ_PERCPU flag")
This change adds the WQ_UNBOUND flag to explicitly request
alloc_workqueue() to be unbound, because this specific workload has no
benefit being per-cpu.
With the introduction of the WQ_PERCPU flag (equivalent to !WQ_UNBOUND),
any alloc_workqueue() caller that doesn’t explicitly specify WQ_UNBOUND
must now use WQ_PERCPU.
Once migration is complete, WQ_UNBOUND can be removed and unbound will
become the implicit default.
Suggested-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Marco Crivellari <marco.crivellari@suse.com>
Link: https://lore.kernel.org/all/20250221112003.1dSuoGyc@linutronix.de/
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20251118102032.54375-2-marco.crivellari@suse.com
- Add delay to the PCC enable/disable in i.MX7ULP composite, needed by
some specific peripherals.
- Simplify the i.MX8MP auxiomix by using devm_auxiliary_device_create()
- Add the i.MX8ULP SIM LPAV platform specific clock provider.
-----BEGIN PGP SIGNATURE-----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=TWjk
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=DDlX
-----END PGP SIGNATURE-----
Merge tag 'clk-imx-6.19' of git://git.kernel.org/pub/scm/linux/kernel/git/abelvesa/linux into clk-imx
Pull i.MX clk driver updates from Abel Vesa:
- Add delay to the PCC enable/disable in i.MX7ULP composite, needed by
some specific peripherals
- Simplify the i.MX8MP auxiomix by using devm_auxiliary_device_create()
- Add the i.MX8ULP SIM LPAV platform specific clock provider
* tag 'clk-imx-6.19' of git://git.kernel.org/pub/scm/linux/kernel/git/abelvesa/linux:
clk: imx: add driver for imx8ulp's sim lpav
dt-bindings: clock: document 8ULP's SIM LPAV
clk: imx: imx8mp-audiomix: use devm_auxiliary_device_create() to simple code
clk: imx: Add some delay before deassert the reset
The rtl8187_rx_cb() calculates the rx descriptor header address
by subtracting its size from the skb tail pointer.
However, it does not validate if the received packet
(skb->len from urb->actual_length) is large enough to contain this
header.
If a truncated packet is received, this will lead to a buffer
underflow, reading memory before the start of the skb data area,
and causing a kernel panic.
Add length checks for both rtl8187 and rtl8187b descriptor headers
before attempting to access them, dropping the packet cleanly if the
check fails.
Fixes: 6f7853f3cb ("rtl8187: change rtl8187_dev.c to support RTL8187B (part 2)")
Signed-off-by: Seungjin Bae <eeodqql09@gmail.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20251118013258.1789949-2-eeodqql09@gmail.com
Remove const qualifier from functions parameter because it was discarded
when container_of was called. Received pointer had mutable access to
it through received container.
Signed-off-by: Adrian Barnaś <abarnas@google.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
When booting with KASAN enabled the following splat is
encountered during probe of the k1 clock driver:
UBSAN: array-index-out-of-bounds in drivers/clk/spacemit/ccu-k1.c:1044:16
index 0 is out of range for type 'clk_hw *[*]'
CPU: 0 UID: 0 PID: 1 Comm: swapper/0 Not tainted 6.18.0-rc5+ #1 PREEMPT(lazy)
Hardware name: Unknown Unknown Product/Unknown Product, BIOS 2022.10spacemit 10/01/2022
Call Trace:
[<ffffffff8002b628>] dump_backtrace+0x28/0x38
[<ffffffff800027d2>] show_stack+0x3a/0x50
[<ffffffff800220c2>] dump_stack_lvl+0x5a/0x80
[<ffffffff80022100>] dump_stack+0x18/0x20
[<ffffffff800164b8>] ubsan_epilogue+0x10/0x48
[<ffffffff8099034e>] __ubsan_handle_out_of_bounds+0xa6/0xa8
[<ffffffff80acbfa6>] k1_ccu_probe+0x37e/0x420
[<ffffffff80b79e6e>] platform_probe+0x56/0x98
[<ffffffff80b76a7e>] really_probe+0x9e/0x350
[<ffffffff80b76db0>] __driver_probe_device+0x80/0x138
[<ffffffff80b76f52>] driver_probe_device+0x3a/0xd0
[<ffffffff80b771c4>] __driver_attach+0xac/0x1b8
[<ffffffff80b742fc>] bus_for_each_dev+0x6c/0xc8
[<ffffffff80b76296>] driver_attach+0x26/0x38
[<ffffffff80b759ae>] bus_add_driver+0x13e/0x268
[<ffffffff80b7836a>] driver_register+0x52/0x100
[<ffffffff80b79a78>] __platform_driver_register+0x28/0x38
[<ffffffff814585da>] k1_ccu_driver_init+0x22/0x38
[<ffffffff80023a8a>] do_one_initcall+0x62/0x2a0
[<ffffffff81401c60>] do_initcalls+0x170/0x1a8
[<ffffffff81401e7a>] kernel_init_freeable+0x16a/0x1e0
[<ffffffff811f7534>] kernel_init+0x2c/0x180
[<ffffffff80025f56>] ret_from_fork_kernel+0x16/0x1d8
[<ffffffff81205336>] ret_from_fork_kernel_asm+0x16/0x18
---[ end trace ]---
This is bogus and is simply a result of KASAN consulting the
`.num` member of the struct for bounds information (as it should
due to `__counted_by`) and finding 0 set by kzalloc() because it
has not been initialized before the loop that fills in the array.
The easy fix is to just move the line that sets `num` to before
the loop that fills the array so that KASAN has the information
it needs to accurately conclude that the access is valid.
Fixes: 1b72c59db0 ("clk: spacemit: Add clock support for SpacemiT K1 SoC")
Tested-by: Yanko Kaneti <yaneti@declera.com>
Signed-off-by: Charles Mirabile <cmirabil@redhat.com>
Reviewed-by: Alex Elder <elder@riscstar.com>
Reviewed-by: Troy Mitchell <troy.mitchell@linux.spacemit.com>
Reviewed-by: Yixun Lan <dlan@gentoo.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Daniel Zahka says:
====================
devlink: net/mlx5: implement swp_l4_csum_mode via devlink params
This series introduces a new devlink feature for querying param
default values, and resetting params to their default values. This
feature is then used to implement a new mlx5 driver param.
The series starts with two pure refactor patches: one that passes
through the extack to devlink_param::get() implementations. And a
second small refactor that prepares the netlink tlv handling code in
the devlink_param::get() path to better handle default parameter
values.
The third patch introduces the uapi and driver api for default
parameter values. The driver api is opt-in, and both the uapi and
driver api preserve existing behavior when not used by drivers or
userspace.
The fourth patch introduces a new mlx5 driver param, swp_l4_csum_mode,
for controlling tx csum behavior. The "l4_only" value of this param is
a dependency for PSP initialization on CX7 NICs.
Lastly, the series introduces a new driver param with cmode runtime to
netdevsim, and then uses this param in a new testcase for netdevsim
devlink params.
Here are some examples of using the default param uapi with the devlink
cli. Note the devlink cli binary I am using has changes which I am
posting in accompanying series targeting iproute2-next:
# netdevsim
./devlink dev param show netdevsim/netdevsim0
netdevsim/netdevsim0:
name max_macs type generic
values:
cmode driverinit value 32 default 32
name test1 type driver-specific
values:
cmode driverinit value true default true
# set to false
./devlink dev param set netdevsim/netdevsim0 name test1 value false cmode driverinit
./devlink dev param show netdevsim/netdevsim0
netdevsim/netdevsim0:
name max_macs type generic
values:
cmode driverinit value 32 default 32
name test1 type driver-specific
values:
cmode driverinit value false default true
# set back to default
./devlink dev param set netdevsim/netdevsim0 name test1 default cmode driverinit
./devlink dev param show netdevsim/netdevsim0
netdevsim/netdevsim0:
name max_macs type generic
values:
cmode driverinit value 32 default 32
name test1 type driver-specific
values:
cmode driverinit value true default true
# mlx5 params on cx7
./devlink dev param show pci/0000:01:00.0
pci/0000:01:00.0:
name max_macs type generic
values:
cmode driverinit value 128 default 128
...
name swp_l4_csum_mode type driver-specific
values:
cmode permanent value default default default
# set to l4_only
./devlink dev param set pci/0000:01:00.0 name swp_l4_csum_mode value l4_only cmode permanent
./devlink dev param show pci/0000:01:00.0 name swp_l4_csum_mode
pci/0000:01:00.0:
name swp_l4_csum_mode type driver-specific
values:
cmode permanent value l4_only default default
# reset to default
./devlink dev param set pci/0000:01:00.0 name swp_l4_csum_mode default cmode permanent
./devlink dev param show pci/0000:01:00.0 name swp_l4_csum_mode
pci/0000:01:00.0:
name swp_l4_csum_mode type driver-specific
values:
cmode permanent value default default default
====================
Link: https://patch.msgid.link/20251119025038.651131-1-daniel.zahka@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Test querying default values and resetting to default values for
netdevsim devlink params.
This should cover the basic paths of interest: driverinit and
non-driverinit cmodes, as well as bool and non-bool value
type. Default param values of type bool are encoded with u8 netlink
type as opposed to flag type, so that userspace can distinguish
"not-present" from false.
Signed-off-by: Daniel Zahka <daniel.zahka@gmail.com>
Link: https://patch.msgid.link/20251119025038.651131-7-daniel.zahka@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Create a new devlink param, test2, that supports default param actions
via the devlink_param::get_default() and
devlink_param::reset_default() functions.
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Daniel Zahka <daniel.zahka@gmail.com>
Link: https://patch.msgid.link/20251119025038.651131-6-daniel.zahka@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
swp_l4_csum_mode controls how L4 transmit checksums are computed when
using Software Parser (SWP) hints for header locations.
Supported values:
1. default: device will choose between full_csum or l4_only. Driver
will discover the device's choice during initialization.
2. full_csum: calculate L4 checksum with the pseudo-header.
3. l4_only: calculate L4 checksum without the pseudo-header. Only
available when swp_l4_csum_mode_l4_only is set in
mlx5_ifc_nv_sw_offload_cap_bits.
Note that 'default' might be returned from the device and passed to
userspace, and it might also be set during a
devlink_param::reset_default() call, but attempts to set a value of
default directly with param-set will be rejected.
The l4_only setting is a dependency for PSP initialization in
mlx5e_psp_init().
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Daniel Zahka <daniel.zahka@gmail.com>
Link: https://patch.msgid.link/20251119025038.651131-5-daniel.zahka@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Support querying and resetting to default param values.
Introduce two new devlink netlink attrs:
DEVLINK_ATTR_PARAM_VALUE_DEFAULT and
DEVLINK_ATTR_PARAM_RESET_DEFAULT. The former is used to contain an
optional parameter value inside of the param_value nested
attribute. The latter is used in param-set requests from userspace to
indicate that the driver should reset the param to its default value.
To implement this, two new functions are added to the devlink driver
api: devlink_param::get_default() and
devlink_param::reset_default(). These callbacks allow drivers to
implement default param actions for runtime and permanent cmodes. For
driverinit params, the core latches the last value set by a driver via
devl_param_driverinit_value_set(), and uses that as the default value
for a param.
Because default parameter values are optional, it would be impossible
to discern whether or not a param of type bool has default value of
false or not provided if the default value is encoded using a netlink
flag type. For this reason, when a DEVLINK_PARAM_TYPE_BOOL has an
associated default value, the default value is encoded using a u8
type.
Signed-off-by: Daniel Zahka <daniel.zahka@gmail.com>
Link: https://patch.msgid.link/20251119025038.651131-4-daniel.zahka@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Lift the param type demux and value attr placement into a separate
function. This new function, devlink_nl_param_put(), can be used to
place additional types values in the value array, e.g., default,
current, next values. This commit has no functional change.
Signed-off-by: Daniel Zahka <daniel.zahka@gmail.com>
Link: https://patch.msgid.link/20251119025038.651131-3-daniel.zahka@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Allow devlink_param::get() handlers to report error messages via
extack. This function is called in a few different contexts, but not
all of them will have an valid extack to use.
When devlink_param::get() is called from param_get_doit or
param_get_dumpit contexts, pass the extack through so that drivers can
report errors when retrieving param values. devlink_param::get() is
called from the context of devlink_param_notify(), pass NULL in for
the extack.
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Daniel Zahka <daniel.zahka@gmail.com>
Link: https://patch.msgid.link/20251119025038.651131-2-daniel.zahka@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add the control sequence of register bits to handle the clocks and the
resets of Video Input Interface.
Signed-off-by: Yuji Ishikawa <yuji2.ishikawa@toshiba.co.jp>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add clock and reset identifiers for the Video Input Interface.
These identifiers support two instances: VIIF0 and VIIF1.
Signed-off-by: Yuji Ishikawa <yuji2.ishikawa@toshiba.co.jp>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Remove the definitions of number of clocks from bindings because they
prevent adding new clocks. Since the previous patch removed all refereces
within the driver, they can now be deleted.
The same for resets and plls.
Signed-off-by: Yuji Ishikawa <yuji2.ishikawa@toshiba.co.jp>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Remove use of TMPV770X_NR_CLK.
Instead, define number of clocks inside the driver directory.
The same for TMPV770X_NR_RESET and TMPV770X_NR_PLL.
Signed-off-by: Yuji Ishikawa <yuji2.ishikawa@toshiba.co.jp>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Gustavo Luiz Duarte says:
====================
netconsole: Allow userdata buffer to grow dynamically
The current netconsole implementation allocates a static buffer for
extradata (userdata + sysdata) with a fixed size of
MAX_EXTRADATA_ENTRY_LEN * MAX_EXTRADATA_ITEMS bytes for every target,
regardless of whether userspace actually uses this feature. This forces
us to keep MAX_EXTRADATA_ITEMS small (16), which is restrictive for
users who need to attach more metadata to their log messages.
This patch series enables dynamic allocation of the userdata buffer,
allowing it to grow on-demand based on actual usage. The series:
1. Refactors send_fragmented_body() to simplify handling of separated
userdata and sysdata (patch 1/4)
2. Splits userdata and sysdata into separate buffers (patch 2/4)
3. Implements dynamic allocation for the userdata buffer (patch 3/4)
4. Increases MAX_USERDATA_ITEMS from 16 to 256 now that we can do so
without memory waste (patch 4/4)
Benefits:
- No memory waste when userdata is not used
- Targets that use userdata only consume what they need
- Users can attach significantly more metadata without impacting systems
that don't use this feature
====================
Link: https://patch.msgid.link/20251119-netconsole_dynamic_extradata-v3-0-497ac3191707@meta.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Increase MAX_USERDATA_ITEMS from 16 to 256 entries now that the userdata
buffer is allocated dynamically.
The previous limit of 16 was necessary because the buffer was statically
allocated for all targets. With dynamic allocation, we can support more
entries without wasting memory on targets that don't use userdata.
This allows users to attach more metadata to their netconsole messages,
which is useful for complex debugging and logging scenarios.
Also update the testcase accordingly.
Signed-off-by: Gustavo Luiz Duarte <gustavold@gmail.com>
Reviewed-by: Breno Leitao <leitao@debian.org>
Link: https://patch.msgid.link/20251119-netconsole_dynamic_extradata-v3-4-497ac3191707@meta.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The userdata buffer in struct netconsole_target is currently statically
allocated with a size of MAX_USERDATA_ITEMS * MAX_EXTRADATA_ENTRY_LEN
(16 * 256 = 4096 bytes). This wastes memory when userdata entries are
not used or when only a few entries are configured, which is common in
typical usage scenarios. It also forces us to keep MAX_USERDATA_ITEMS
small to limit the memory wasted.
Change the userdata buffer from a static array to a dynamically
allocated pointer. The buffer is now allocated on-demand in
update_userdata() whenever userdata entries are added, modified, or
removed via configfs. The implementation calculates the exact size
needed for all current userdata entries, allocates a new buffer of that
size, formats the entries into it, and atomically swaps it with the old
buffer.
This approach provides several benefits:
- Memory efficiency: Targets with no userdata use zero bytes instead of
4KB, and targets with userdata only allocate what they need;
- Scalability: Makes it practical to increase MAX_USERDATA_ITEMS to a
much larger value without imposing a fixed memory cost on every
target;
- No hot-path overhead: Allocation occurs during configuration (write to
configfs), not during message transmission
If memory allocation fails during userdata update, -ENOMEM is returned
to userspace through the configfs attribute write operation.
The sysdata buffer remains statically allocated since it has a smaller
fixed size (MAX_SYSDATA_ITEMS * MAX_EXTRADATA_ENTRY_LEN = 4 * 256 = 1024
bytes) and its content length is less predictable.
Signed-off-by: Gustavo Luiz Duarte <gustavold@gmail.com>
Reviewed-by: Breno Leitao <leitao@debian.org>
Link: https://patch.msgid.link/20251119-netconsole_dynamic_extradata-v3-3-497ac3191707@meta.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Separate userdata and sysdata into distinct buffers to enable independent
management. Previously, both were stored in a single extradata_complete
buffer with a fixed size that accommodated both types of data.
This separation allows:
- userdata to grow dynamically (in subsequent patch)
- sysdata to remain in a small static buffer
- removal of complex entry counting logic that tracked both types together
The split also simplifies the code by eliminating the need to check total
entry count across both userdata and sysdata when enabling features,
which allows to drop holding su_mutex on sysdata_*_enabled_store().
No functional change in this patch, just structural preparation for
dynamic userdata allocation.
Signed-off-by: Gustavo Luiz Duarte <gustavold@gmail.com>
Reviewed-by: Breno Leitao <leitao@debian.org>
Link: https://patch.msgid.link/20251119-netconsole_dynamic_extradata-v3-2-497ac3191707@meta.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Refactor send_fragmented_body() to use separate offset tracking for
msgbody, and extradata instead of complex conditional logic.
The previous implementation used boolean flags and calculated offsets
which made the code harder to follow.
The new implementation maintains independent offset counters
(msgbody_offset, extradata_offset) and processes each section
sequentially, making the data flow more straightforward and the code
easier to maintain.
This is a preparatory refactoring with no functional changes, which will
allow easily splitting extradata_complete into separate userdata and
sysdata buffers in the next patch.
Signed-off-by: Gustavo Luiz Duarte <gustavold@gmail.com>
Reviewed-by: Breno Leitao <leitao@debian.org>
Link: https://patch.msgid.link/20251119-netconsole_dynamic_extradata-v3-1-497ac3191707@meta.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
To eliminate the use of struct page in page pool, the page pool users
should use netmem descriptor and APIs instead.
Make fbnic access @pp through netmem_desc instead of page.
Signed-off-by: Byungchul Park <byungchul@sk.com>
Link: https://patch.msgid.link/20251120011118.73253-1-byungchul@sk.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As explain in commit fa349e396e ("veth: Fix race with AF_XDP exposing
old or uninitialized descriptors") for veth there is a chance after
napi_complete_done() that another CPU can manage start another NAPI
instance running veth_pool(). For NAPI this is correctly handled as the
napi_schedule_prep() check will prevent multiple instances from getting
scheduled, but for the remaining code in veth_pool() this can run
concurrent with the newly started NAPI instance.
The problem/race is that xdp_clear_return_frame_no_direct() isn't
designed to be nested.
Prior to commit 401cb7dae8 ("net: Reference bpf_redirect_info via
task_struct on PREEMPT_RT.") the temporary BPF net context
bpf_redirect_info was stored per CPU, where this wasn't an issue. Since
this commit the BPF context is stored in 'current' task_struct. When
running veth in threaded-NAPI mode, then the kthread becomes the storage
area. Now a race exists between two concurrent veth_pool() function calls
one exiting NAPI and one running new NAPI, both using the same BPF net
context.
Race is when another CPU gets within the xdp_set_return_frame_no_direct()
section before exiting veth_pool() calls the clear-function
xdp_clear_return_frame_no_direct().
Fixes: 401cb7dae8 ("net: Reference bpf_redirect_info via task_struct on PREEMPT_RT.")
Signed-off-by: Jesper Dangaard Brouer <hawk@kernel.org>
Link: https://patch.msgid.link/176356963888.337072.4805242001928705046.stgit@firesoul
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Wei Fang says:
====================
net: fec: do some cleanup for the driver
This patch set removes some unnecessary or invalid code from the FEC
driver. See each patch for details.
====================
Link: https://patch.msgid.link/20251119025148.2817602-1-wei.fang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There are two sets of macros used to define the status bits of TX and RX
BDs, one is the BD_SC_xx macros, the other one is the BD_ENET_xx macros.
For the BD_SC_xx macros, only BD_SC_WRAP is used in the driver. But the
BD_ENET_xx macros are more widely used in the driver, and they define
more bits of the BD status. Therefore, remove the BD_SC_xx macros from
now on.
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20251119025148.2817602-6-wei.fang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The rx_align was introduced by the commit 41ef84ce4c ("net: fec: change
FEC alignment according to i.mx6 sx requirement"). Because the i.MX6 SX
requires RX buffer must be 64 bytes alignment.
Since the commit 95698ff617 ("net: fec: using page pool to manage RX
buffers"), the address of the RX buffer is always the page address plus
FEC_ENET_XDP_HEADROOM which is 256 bytes, so the RX buffer is always
64-byte aligned. Therefore, rx_align has no effect since that commit,
and we can safely remove it.
In addition, to prevent future modifications to FEC_ENET_XDP_HEADROOM,
a BUILD_BUG_ON() test has been added to the driver, which ensures that
FEC_ENET_XDP_HEADROOM provides the required alignment.
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Link: https://patch.msgid.link/20251119025148.2817602-5-wei.fang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The struct fec_enet_priv_txrx_info has three members: offset, page and
skb. The offset is only initialized in the driver and is not used, the
skb is never initialized and used in the driver. The both will not be
used in the future. Therefore, replace struct fec_enet_priv_txrx_info
directly with struct page.
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20251119025148.2817602-4-wei.fang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
From the Kconfig file, we can see CONFIG_FEC depends on the following
platform-related options.
ColdFire: M523x, M527x, M5272, M528x, M520x and M532x
S32: ARCH_S32 (ARM64)
i.MX: SOC_IMX28 and ARCH_MXC (ARM and ARM64)
Based on the code of fec driver, only some macro definitions on the
M5272 platform are different from those on other platforms. Therefore,
we can simplify the following complex preprocessor directives to
"if !defined(CONFIG_M5272)".
"#if defined(CONFIG_M523x) || defined(CONFIG_M527x) || \
defined(CONFIG_M528x) || defined(CONFIG_M520x) || \
defined(CONFIG_M532x) || defined(CONFIG_ARM) || \
defined(CONFIG_ARM64)"
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Link: https://patch.msgid.link/20251119025148.2817602-3-wei.fang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The conditional preprocessor directive was added to fix build errors on
the MCF5272 platform, see commit d13919301d ("net: fec: Fix build for
MCF5272"). The compilation errors were originally caused by some register
macros not being defined on that platform.
The driver now uses quirks to dynamically handle platform differences,
and for MCF5272, its quirks is 0, so it does not support RACC and GBIT
Ethernet. So these preprocessor directives are no longer required and
can be safely removed without causing build or functional issue.
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Link: https://patch.msgid.link/20251119025148.2817602-2-wei.fang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, the check for whether a partition is populated does not
account for tasks in the cpuset of attaching. This is a corner case
that can leave a task stuck in a partition with no effective CPUs.
The race condition occurs as follows:
cpu0 cpu1
//cpuset A with cpu N
migrate task p to A
cpuset_can_attach
// with effective cpus
// check ok
// cpuset_mutex is not held // clear cpuset.cpus.exclusive
// making effective cpus empty
update_exclusive_cpumask
// tasks_nocpu_error check ok
// empty effective cpus, partition valid
cpuset_attach
...
// task p stays in A, with non-effective cpus.
To fix this issue, this patch introduces cs_is_populated, which considers
tasks in the attaching cpuset. This new helper is used in validate_change
and partition_is_populated.
Fixes: e2d59900d9 ("cgroup/cpuset: Allow no-task partition to have empty cpuset.cpus.effective")
Signed-off-by: Chen Ridong <chenridong@huawei.com>
Reviewed-by: Waiman Long <longman@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Tariq Toukan says:
====================
net: Add 1600Gbps (1.6T) link mode support
This series by Yael adds 1600Gbps (1.6T) link mode support.
See detailed description by Yael below.
====================
Link: https://patch.msgid.link/1763585297-1243980-1-git-send-email-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for 1600Gbps speed to allow using 3ad mode with 1600G
devices.
Signed-off-by: Yael Chemla <ychemla@nvidia.com>
Reviewed-by: Shahar Shitrit <shshitrit@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/1763585297-1243980-4-git-send-email-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Introduce support for a 1600Gbps link mode, utilizing 8 lanes at 200Gbps
per lane.
Signed-off-by: Yael Chemla <ychemla@nvidia.com>
Reviewed-by: Shahar Shitrit <shshitrit@nvidia.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/1763585297-1243980-3-git-send-email-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add a sample tool demonstrating how to add, dump, and delete a
flower filter with two VLAN push actions. The example can be
invoked as:
# samples/tc-filter-add p2
flower pref 1 proto: 0x8100
flower:
vlan_id: 100
vlan_prio: 5
num_of_vlans: 3
action order: 1 vlan push id 200 protocol 0x8100 priority 0
action order: 2 vlan push id 300 protocol 0x8100 priority 0
This verifies correct handling of tc action attributes for multiple
VLAN push actions. The tc action indexed arrays start from index 1,
and the index defines the action order. This behavior differs from
the YNL specification, which expects arrays to be zero-based. To
accommodate this, the example adds a dummy action at index 0, which
is ignored by the kernel.
Signed-off-by: Zahari Doychev <zahari.doychev@linux.com>
Link: https://patch.msgid.link/20251119203618.263780-2-zahari.doychev@linux.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski says:
====================
selftests: drv-net: convert GRO and Toeplitz tests to work for drivers in NIPA
Main objective of this series is to convert the gro.sh and toeplitz.sh
tests to be "NIPA-compatible" - meaning make use of the Python env,
which lets us run the tests against either netdevsim or a real device.
The tests seem to have been written with a different flow in mind.
Namely they source different bash "setup" scripts depending on arguments
passed to the test. While I have nothing against the use of bash and
the overall architecture - the existing code needs quite a bit of work
(don't assume MAC/IP addresses, support remote endpoint over SSH).
If I'm the one fixing it, I'd rather convert them to our "simplistic"
Python.
This series rewrites the tests in Python while addressing their
shortcomings. The functionality of running the test over loopback
on a real device is retained but with a different method of invocation
(see the last patch).
Once again we are dealing with a script which run over a variety of
protocols (combination of [ipv4, ipv6, ipip] x [tcp, udp]). The first
4 patches add support for test variants to our scripts. We use the
term "variant" in the same sense as the C kselftest_harness.h -
variant is just a set of static input arguments.
Note that neither GRO nor the Toeplitz test fully passes for me on
any HW I have access to. But this is unrelated to the conversion.
This series is not making any real functional changes to the tests,
it is limited to improving the "test harness" scripts.
====================
Link: https://patch.msgid.link/20251120021024.2944527-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
gro.sh and toeplitz.sh used to source in one of two setup scripts
depending on whether the test was expected to be run against
veth or a real device. veth testing is replaced by netdevsim
and existing "remote endpoint" support in our Python tests.
Add a script which sets up loopback mode.
The usage is a little bit more complicated than running
the scripts used to be. Testing used to work like this:
./../gro.sh -i eth0 ...
now the "setup script" has to be run explicitly:
NETIF=eth0 ./../ksft_setup_loopback.sh ./../gro.sh
But the functionality itself is retained.
Reviewed-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://patch.msgid.link/20251120021024.2944527-13-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
