Add "ref" clock for i.MX95's pcie and fix below CHECK_DTBS warnings:
arch/arm64/boot/dts/freescale/imx95-19x19-evk.dtb: pcie@4c300000: clock-names: ['pcie', 'pcie_bus', 'pcie_phy', 'pcie_aux'] is too short
from schema $id: http://devicetree.org/schemas/pci/fsl,imx6q-pcie.yaml
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
disable-gpio is an (old) downstream kernel property, which slipped into
DT. Remove it.
Fixes: c01a26b8897a ("arm64: dts: mba8xx: Add PCIe support")
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
TQMa6UL1 has only one FEC which needs to be disabled as one of the last
steps.
imx6ul-tqma6ul2.dtsi can't be included in imx6ul-tqma6ul1.dtsi as the
defaults from imx6ul.dtsi will be applied again.
Fixes: 7b8861d8e6 ("ARM: dts: imx6ul: add TQ-Systems MBa6ULx device trees")
Signed-off-by: Max Merchel <Max.Merchel@ew.tq-group.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
IRQ mapping is already present. Add the missing DMA interrupt. This is
similar to commit 9d9c56025e429 ("arm64: dts: imx8-ss-hsio: Wire up DMA
IRQ for PCIe")
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Move port@0 and port@1 under ports to fix below DTB_CHECK warnings.
arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dtb: usb@38100000: port@0:reg:0:0: 0 is less than the minimum of 1
from schema $id: http://devicetree.org/schemas/usb/snps,dwc3.yaml#
arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dtb: usb@38100000: Unevaluated properties are not allowed ('#address-cells', '#size-cells', 'dr_mode', 'phy-names', 'phys', 'port@0', 'port@1', 'snps,parkmode-disable-ss-quirk' were unexpected)
from schema $id: http://devicetree.org/schemas/usb/snps,dwc3.yaml#
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The card name for ALSA is generated from the model name string and
is limited to 16 characters. Use a shorter name to prevent cutting the
name.
Since nearly all starter kit mainboards for i.MX based SoM by TQ-Systems
use the same codec with the same routing on board it is a good idea to
use the same model name for the sound card. This allows sharing a default
asound.conf in BSP over all the kits.
Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The card name for ALSA is generated from the model name string and
is limited to 16 characters. Use a shorter name to prevent cutting the
name.
Since nearly all starter kit mainboards for i.MX based SoM by TQ-Systems
use the same codec with the same routing on board it is a good idea to
use the same model name for the sound card. This allows sharing a default
asound.conf in BSP over all the kits.
Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add i3c1 and i3c2 support.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The original code used if statements to update discovered VPD pages when
found. This had the side-effect of not breaking the loop when a page was
found.
Use an idiomatic switch statement instead.
Signed-off-by: Chaohai Chen <wdhh6@aliyun.com>
Link: https://lore.kernel.org/r/20250226065802.234144-1-wdhh6@aliyun.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
gpio-pca95xx.yaml documents 'nxp,pca9554', so use this compatible
to fix the following dt-schema warning:
failed to match any schema with compatible: ['pca9554']
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to mxc-nand.yaml, the correct node name must be
'nand-controller'.
Change it accordingly to fix the following dt-schema warning:
$nodename:0: 'nand@b8000000' does not match '^nand-controller(@.*)?'
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to fsl,dspi.yaml the expected order for describing the dmas
and dma-names properties is "tx" first, followed by "rx".
Adjust it acordingly to fix the following dt-schema warnings:
spi@4002c000: dma-names:0: 'tx' was expected
spi@4002c000: dma-names:1: 'rx' was expected
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The bootloader adds MTD partitions in this subnode if present.
Add an empty partitions node which the bootloader will fill with
configured MTD partitions.
Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
(Q)SPI NOR flash is supplied by 3.3V. Add the corresponding supply.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The bootloader adds MTD partitions in this subnode if present, or in the
spi-nor node itself otherwise.
Setting #size-cells in MTD nodes itself is deprecated by mtd.yaml.
Fix all this by adding an empty partitions node which the bootloader will
fill with configured MTD partitions. Remove the deprecated properties
as well.
Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
(Q)SPI NOR flash is supplied by 1.8V. Add the corresponding supply.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The bootloader may add MTD partitions in this subnode if present.
Add an empty partitions node which the bootloader will fill with
configured MTD partitions. Remove #size-cells from MTD node
because this is deprecated.
Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This matches the real hardware and allows to remove
the virtual 3.3V regulator.
Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This is a fixed 3.3V rail supplying several hardware on SOM.
Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This board is very similar to the already upstream
imx8mp-skov-revb-mi1010ait-1cp1.dts with the difference that it uses a
different 7" LVDS panel.
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The BD500 replaces the touch display with 3 bicolor LEDs and a push
button on top of a Skov i.MX8-CPU revision C.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
I2C bus recovery can be used to recover when SCL/SDA are stuck low.
To be able to use it, add the necessary GPIO and pinctrl entries.
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
I2C2 is exposed on a pin header on the base board, so its pinmux is
always the same if it's enabled.
Therefore, move the definition to the common DTSI, so board DTs only
need to override the status to enable it.
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
All Skov i.MX8MP boards share the same baseboard (modulo revisions)
and are booted with the same bootloader image, which samples some
strapping pins at startup and determines which kernel device tree
to use.
For use as bootloader device tree and as fallback, when no matching
device tree has been found, add a basic variant that doesn't configure
any variant-specific peripherals like displays.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The Skov i.MX8MP boards are a family of climate controllers.
In preparation for adding device trees for three more variants,
describe their DT compatible in the bindings.
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
To reduce heat generation, the Skov i.MX8MP boards should run in nominal
drive mode with a VDD_SOC voltage of 850 mV.
At this operating point, not all frequencies that are achievable with
overdrive mode are possible, so import imx8mp-nominal.dtsi to clock down
the clocks.
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The comment in the DT mentions that "currently it is not possible to let
display clocks configure automatically, so we need to set them manually".
Since commit ff06ea04e4 ("clk: imx: clk-imx8mp: Allow media_disp pixel
clock reconfigure parent rate"), this is no longer the case.
Make use of this new functionality by dropping the now unneeded
assigned-clock-rates in &media_blk_ctrl.
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Acked-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The imx8mp-nominal.dtsi is meant to be included into boards that want to
override the default overdrive clock settings with settings suitable for
running in nominal drive mode at its lower required voltage.
Specifying fsl,operating-mode = "nominal" informs drivers of this fact,
so they can sanity check runtime clock reconfiguration to observe the
limits imposed by nominal mode.
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Unlike the i.MX8MM and i.MX8MN SoCs added earlier, the device tree for
the i.MX8MP configures some clocks at frequencies that are only validated
for overdrive mode, i.e. when VDD_SOC is 950 mV.
Boards may want to run their SoC at the lower voltage of 850 mV though
to reduce heat generation and power usage. For this to work, clock rates
need to adhere to the limits of the nominal drive mode.
Add an optional DTSI file which can be included by various boards to run
in this mode.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add initialization code for R-Car S4-8 ES1.2 to improve transfer stability.
Using the new code requires downloading firmware and reading calibration
data from E-FUSE. If either fails, the driver falls back to the old
initialization code.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Co-developed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/97d83709495c764b2456d4d25846f5f48197cad0.1741179611.git.geert+renesas@glider.be
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
After refactoring the code, ufs_renesas_reg_control() is no longer needed,
because all operations are simple and can be called directly. Remove the
ufs_renesas_reg_control() helper function, and call udelay() directly.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/69500e4c18be1ca1de360f9e797e282ffef04004.1741179611.git.geert+renesas@glider.be
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add support for returning read register values from
ufs_renesas_reg_control(), so ufs_renesas_set_phy() can use the existing
ufs_renesas_write_phy() helper. Remove the now unused code to save to,
set, and restore from a static array inside ufs_renesas_reg_control().
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/9fa240a9dc0308d6675138f8434eccb77f051650.1741179611.git.geert+renesas@glider.be
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since initialization of the UFS controller on R-Car S4-8 ES1.0 requires
only static values, the driver uses initialization data stored in the const
ufs_param[] array. However, other UFS controller variants (R-Car S4-8
ES1.2) require dynamic values, like those obtained from E-FUSE. Refactor
the initialization code to prepare for this.
This also reduces kernel size by almost 30 KiB.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/3520e27ac7ff512de6508f630eee3c1689a7c73d.1741179611.git.geert+renesas@glider.be
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
On R-Car S4-8 ES1.2, the E-FUSE block contains PLL and AFE tuning
parameters for the Universal Flash Storage controller. Document the
related NVMEM properties, and update the example.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/2f337169f8183d48b7d94ee13565fea804aade84.1741179611.git.geert+renesas@glider.be
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add Task Abort support to handle SCSI command timeouts, ensuring recovery
and cleanup of timed-out commands. This completes the error handling
framework for mpi3mr driver, which already includes device reset, target
reset, bus reset, and host reset.
Co-developed-by: Sathya Prakash <sathya.prakash@broadcom.com>
Signed-off-by: Sathya Prakash <sathya.prakash@broadcom.com>
Signed-off-by: Chandrakanth Patil <chandrakanth.patil@broadcom.com>
Link: https://lore.kernel.org/r/20250304191453.12994-1-chandrakanth.patil@broadcom.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A lot of other clocks on the i.MX8MP, including the DRAM set up by the
bootloader are already running at overdrive clock rates. While this is a
deviation from the configuration of other i.MX8M* family SoCs, overdrive
is the default for most i.MX8MP boards and only some special purpose
boards will choose to run the SoC at nominal drive rates. Up the GPU and
NPU clock rates to their overdrive level to be consistent with other
clocks set up in the dtsi.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
A device tree binding for the Microchip USB5744 hub controller
was added in commit 02be19e914 ("dt-bindings: usb: Add support
for Microchip usb5744 hub controller").
U-Boot will consume this binding in order to perform the
necessary actions to enable the USB hub ports over I2C.
(We previously used our own out-of-tree driver for
this task)
The Ten64 board does not have any switchable supplies
for the voltage rails utilized by the USB5744, so a
pair of dummy supplies have been added to facilitate
operation with U-Boot's hub driver.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The log statement reports the packet status code as the hv status code
which causes confusion when debugging as "hv" might refer to a hypervisor,
and sometimes to the host part of the Hyper-V virtualization stack.
Fix the name of the datum being logged to clearly indicate the component
reporting the error. Also log it in hexadecimal everywhere for consistency.
Signed-off-by: Roman Kisel <romank@linux.microsoft.com>
Link: https://lore.kernel.org/r/20250304000940.9557-2-romank@linux.microsoft.com
Reviewed-by: Easwar Hariharan <eahariha@linux.microsoft.com>
Reviewed-by: Michael Kelley <mhklinux@outlook.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Most of the module parameters are only used locally in the same C file; so
static them.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Link: https://lore.kernel.org/r/20250309145044.38586-1-linux@treblig.org
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Most of the module parameters are only used locally in the same C file; so
static them.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Link: https://lore.kernel.org/r/20250309143348.32896-1-linux@treblig.org
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>