The UART’s software and hardware flow control are currently not
functioning correctly.
For software flow control, the following error is encountered:
qcom_geni_serial 1a80000.serial: Couldn't find suitable
clock rate for 56000000, 3500000, 2500000, 1152000, 921600, 19200
During hardware flow control testing, a “Retry 0: Got ZCAN error” is
observed.
To address these issues, update the UART frequency table to include all
supported frequencies according to the frequency plan.
Fixes: 21b5d5a4a3 ("clk: qcom: add Global Clock controller (GCC) driver for IPQ5424 SoC")
Signed-off-by: Manikanta Mylavarapu <quic_mmanikan@quicinc.com>
Link: https://lore.kernel.org/r/20250124060914.1564681-1-quic_mmanikan@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
BRANCH_HALT_ENABLE and BRANCH_HALT_ENABLE_VOTED flags are used to check
halt status of branch clocks, which have an inverted logic for the halt
bit in CBCR register. However, the current logic in the _check_halt()
method only compares the BRANCH_HALT_ENABLE flags, ignoring the votable
branch clocks.
Update the logic to correctly handle the invert logic for votable clocks
using the BRANCH_HALT_ENABLE_VOTED flags.
Fixes: 9092d1083a ("clk: qcom: branch: Extend the invert logic for branch2 clocks")
Cc: stable@vger.kernel.org
Signed-off-by: Ajit Pandey <quic_ajipan@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20250128-push_fix-v1-1-fafec6747881@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
This will allow linux to properly reset eMMC/SD blocks.
Signed-off-by: Alexey Minnekhanov <alexeymin@postmarketos.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250203063427.358327-3-alexeymin@postmarketos.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
SDM429 has mostly the same rpm clocks as MSM8953, but lacks RF_CLK3 and
IPA_CLK and additionally has the BB_CLK3.
Signed-off-by: Daniil Titov <daniilt971@gmail.com>
Signed-off-by: Barnabás Czémán <barnabas.czeman@mainlining.org>
Link: https://lore.kernel.org/r/20250212-sdm429-rpm-v1-2-0a24ac19a478@mainlining.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Reading few registers at the end of the block (e.g. 0x10000, 0x10004)
results in synchronous external abort, so limit the regmap to the last
readable register which allows dumping the regs for debugging.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250212163243.237658-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
- Mukesh and Viken take over maintainership of the Qualcomm I2C
driver.
- Krzysztof Adamski is removed as maintainer of the Axxia I2C
driver.
-----BEGIN PGP SIGNATURE-----
iIwEABYIADQWIQScDfrjQa34uOld1VLaeAVmJtMtbgUCZ680TBYcYW5kaS5zaHl0
aUBrZXJuZWwub3JnAAoJENp4BWYm0y1uYZIA/io0vuV+JMXD/bVbJfVlKeJLTPFK
kJDLQKB510x0Jbc9AQCTPQ1i07pNXliv4FfRyrg8VxhA+MiaeYL7ndruGiRuDQ==
=Qqyn
-----END PGP SIGNATURE-----
Merge tag 'i2c-host-fixes-6.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/andi.shyti/linux into i2c/for-current
i2c-host-fixes for v6.14-rc3
- Mukesh and Viken take over maintainership of the Qualcomm I2C
driver.
- Krzysztof Adamski is removed as maintainer of the Axxia I2C
driver.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQRTLbB6QfY48x44uB6AXGG7T9hjvgUCZ672+AAKCRCAXGG7T9hj
vqnNAP99iQfUC5je/UYE4k9ku0oRD9+d65G5YCmnLv5egUOuTgD/UT+N0LYaahS7
5hRh61sicj57dsrN4kA4U4TpVvoFsAY=
=CUIl
-----END PGP SIGNATURE-----
Merge tag 'for-linus-6.14-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fixes from Juergen Gross:
"Three fixes to xen-swiotlb driver:
- two fixes for issues coming up due to another fix in 6.12
- addition of an __init annotation"
* tag 'for-linus-6.14-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
Xen/swiotlb: mark xen_swiotlb_fixup() __init
x86/xen: allow larger contiguous memory regions in PV guests
xen/swiotlb: relax alignment requirements
Fix several issues in partition probing:
- The bailout for a bad partoffset must use put_dev_sector(), since the
preceding read_part_sector() succeeded.
- If the partition table claims a silly sector size like 0xfff bytes
(which results in partition table entries straddling sector boundaries),
bail out instead of accessing out-of-bounds memory.
- We must not assume that the partition table contains proper NUL
termination - use strnlen() and strncmp() instead of strlen() and
strcmp().
Cc: stable@vger.kernel.org
Signed-off-by: Jann Horn <jannh@google.com>
Link: https://lore.kernel.org/r/20250214-partition-mac-v1-1-c1c626dffbd5@google.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
It is required by firmware to wait up to 2 seconds for pending commands
before sending the destroy hardware context command. After 2 seconds
wait, if there are still pending commands, driver needs to cancel them.
So the context destroy steps need to be:
1. Stop drm scheduler. (drm_sched_entity_destroy)
2. Wait up to 2 seconds for pending commands.
3. Destroy hardware context and cancel the rest pending requests.
4. Wait all jobs associated with the hwctx are freed.
5. Free job resources.
Signed-off-by: Lizhi Hou <lizhi.hou@amd.com>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Signed-off-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250124173536.148676-1-lizhi.hou@amd.com
Convert the shadow MMU to use per-rmap locking instead of the per-VM
mmu_lock to protect rmaps when aging SPTEs. When A/D bits are enabled, it
is safe to simply clear the Accessed bits, i.e. KVM just needs to ensure
the parent page table isn't freed.
The less obvious case is marking SPTEs for access tracking in the
non-A/D case (for EPT only). Because aging a gfn means making the SPTE
not-present, KVM needs to play nice with the case where the CPU has TLB
entries for a SPTE that is not-present in memory. For example, when
doing dirty tracking, if KVM encounters a non-present shadow accessed SPTE,
KVM must know to do a TLB invalidation.
Fortunately, KVM already provides (and relies upon) the necessary
functionality. E.g. KVM doesn't flush TLBs when aging pages (even in the
clear_flush_young() case), and when harvesting dirty bitmaps, KVM flushes
based on the dirty bitmaps, not on SPTEs.
Co-developed-by: James Houghton <jthoughton@google.com>
Signed-off-by: James Houghton <jthoughton@google.com>
Link: https://lore.kernel.org/r/20250204004038.1680123-12-jthoughton@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
Add a lockless version of for_each_rmap_spte(), which is pretty much the
same as the normal version, except that it doesn't BUG() the host if a
non-present SPTE is encountered. When mmu_lock is held, it should be
impossible for a different task to zap a SPTE, _and_ zapped SPTEs must
be removed from their rmap chain prior to dropping mmu_lock. Thus, the
normal walker BUG()s if a non-present SPTE is encountered as something is
wildly broken.
When walking rmaps without holding mmu_lock, the SPTEs pointed at by the
rmap chain can be zapped/dropped, and so a lockless walk can observe a
non-present SPTE if it runs concurrently with a different operation that
is zapping SPTEs.
Signed-off-by: James Houghton <jthoughton@google.com>
Link: https://lore.kernel.org/r/20250204004038.1680123-11-jthoughton@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
Steal another bit from rmap entries (which are word aligned pointers, i.e.
have 2 free bits on 32-bit KVM, and 3 free bits on 64-bit KVM), and use
the bit to implement a *very* rudimentary per-rmap spinlock. The only
anticipated usage of the lock outside of mmu_lock is for aging gfns, and
collisions between aging and other MMU rmap operations are quite rare,
e.g. unless userspace is being silly and aging a tiny range over and over
in a tight loop, time between contention when aging an actively running VM
is O(seconds). In short, a more sophisticated locking scheme shouldn't be
necessary.
Note, the lock only protects the rmap structure itself, SPTEs that are
pointed at by a locked rmap can still be modified and zapped by another
task (KVM drops/zaps SPTEs before deleting the rmap entries)
Co-developed-by: James Houghton <jthoughton@google.com>
Signed-off-by: James Houghton <jthoughton@google.com>
Link: https://lore.kernel.org/r/20250204004038.1680123-10-jthoughton@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
Refactor the pte_list and rmap code to always read and write rmap_head->val
exactly once, e.g. by collecting changes in a local variable and then
propagating those changes back to rmap_head->val as appropriate. This will
allow implementing a per-rmap rwlock (of sorts) by adding a LOCKED bit into
the rmap value alongside the MANY bit.
Signed-off-by: James Houghton <jthoughton@google.com>
Acked-by: Yu Zhao <yuzhao@google.com>
Reviewed-by: James Houghton <jthoughton@google.com>
Link: https://lore.kernel.org/r/20250204004038.1680123-9-jthoughton@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
When aging SPTEs and the TDP MMU is enabled, process the shadow MMU if and
only if the VM has at least one shadow page, as opposed to checking if the
VM has rmaps. Checking for rmaps will effectively yield a false positive
if the VM ran nested TDP VMs in the past, but is not currently doing so.
Signed-off-by: James Houghton <jthoughton@google.com>
Acked-by: Yu Zhao <yuzhao@google.com>
Link: https://lore.kernel.org/r/20250204004038.1680123-8-jthoughton@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
Reorder the processing of the TDP MMU versus the shadow MMU when aging
SPTEs, and skip the shadow MMU entirely in the test-only case if the TDP
MMU reports that the page is young, i.e. completely avoid taking mmu_lock
if the TDP MMU SPTE is young. Swap the order for the test-and-age helper
as well for consistency.
Signed-off-by: James Houghton <jthoughton@google.com>
Acked-by: Yu Zhao <yuzhao@google.com>
Link: https://lore.kernel.org/r/20250204004038.1680123-7-jthoughton@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
Walk the TDP MMU in an RCU read-side critical section without holding
mmu_lock when harvesting and potentially updating age information on
TDP MMU SPTEs. Add a new macro to do RCU-safe walking of TDP MMU roots,
and do all SPTE aging with atomic updates; while clobbering Accessed
information is ok, KVM must not corrupt other bits, e.g. must not drop
a Dirty or Writable bit when making a SPTE young..
If updating a SPTE to mark it for access tracking fails, leave it as is
and treat it as if it were young. If the spte is being actively modified,
it is most likely young.
Acquire and release mmu_lock for write when harvesting age information
from the shadow MMU, as the shadow MMU doesn't yet support aging outside
of mmu_lock.
Suggested-by: Yu Zhao <yuzhao@google.com>
Signed-off-by: James Houghton <jthoughton@google.com>
Reviewed-by: David Matlack <dmatlack@google.com>
Link: https://lore.kernel.org/r/20250204004038.1680123-5-jthoughton@google.com
[sean: massage changelog]
Signed-off-by: Sean Christopherson <seanjc@google.com>
In anticipation of aging SPTEs outside of mmu_lock, force A/D-disabled
SPTEs to be updated atomically, as aging A/D-disabled SPTEs will mark them
for access-tracking outside of mmu_lock. Coupled with restoring access-
tracked SPTEs in the fast page fault handler, the end result is that
A/D-disable SPTEs will be volatile at all times.
Reviewed-by: James Houghton <jthoughton@google.com>
Link: https://lore.kernel.org/all/Z60bhK96JnKIgqZQ@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
Don't force SPTE modifications to be done atomically if the only volatile
bit in the SPTE is the Accessed bit. KVM and the primary MMU tolerate
stale aging state, and the probability of an Accessed bit A/D assist being
clobbered *and* affecting again is likely far lower than the probability
of consuming stale information due to not flushing TLBs when aging.
Rename spte_has_volatile_bits() to spte_needs_atomic_update() to better
capture the nature of the helper.
Opportunstically do s/write/update on the TDP MMU wrapper, as it's not
simply the "write" that needs to be done atomically, it's the entire
update, i.e. the entire read-modify-write operation needs to be done
atomically so that KVM has an accurate view of the old SPTE.
Leave kvm_tdp_mmu_write_spte_atomic() as is. While the name is imperfect,
it pairs with kvm_tdp_mmu_write_spte(), which in turn pairs with
kvm_tdp_mmu_read_spte(). And renaming all of those isn't obviously a net
positive, and would require significant churn.
Signed-off-by: James Houghton <jthoughton@google.com>
Link: https://lore.kernel.org/r/20250204004038.1680123-6-jthoughton@google.com
Co-developed-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Sean Christopherson <seanjc@google.com>
This new function, tdp_mmu_clear_spte_bits_atomic(), will be used in a
follow-up patch to enable lockless Accessed bit clearing.
Signed-off-by: James Houghton <jthoughton@google.com>
Acked-by: Yu Zhao <yuzhao@google.com>
Link: https://lore.kernel.org/r/20250204004038.1680123-4-jthoughton@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
It is possible to correctly do aging without taking the KVM MMU lock,
or while taking it for read; add a Kconfig to let architectures do so.
Architectures that select KVM_MMU_LOCKLESS_AGING are responsible for
correctness.
Suggested-by: Yu Zhao <yuzhao@google.com>
Signed-off-by: James Houghton <jthoughton@google.com>
Reviewed-by: David Matlack <dmatlack@google.com>
Link: https://lore.kernel.org/r/20250204004038.1680123-3-jthoughton@google.com
[sean: massage shortlog+changelog, fix Kconfig goof and shorten name]
Signed-off-by: Sean Christopherson <seanjc@google.com>
When some client process A call pdr_add_lookup() to add the look up for
the service and does schedule locator work, later a process B got a new
server packet indicating locator is up and call pdr_locator_new_server()
which eventually sets pdr->locator_init_complete to true which process A
sees and takes list lock and queries domain list but it will timeout due
to deadlock as the response will queued to the same qmi->wq and it is
ordered workqueue and process B is not able to complete new server
request work due to deadlock on list lock.
Fix it by removing the unnecessary list iteration as the list iteration
is already being done inside locator work, so avoid it here and just
call schedule_work() here.
Process A Process B
process_scheduled_works()
pdr_add_lookup() qmi_data_ready_work()
process_scheduled_works() pdr_locator_new_server()
pdr->locator_init_complete=true;
pdr_locator_work()
mutex_lock(&pdr->list_lock);
pdr_locate_service() mutex_lock(&pdr->list_lock);
pdr_get_domain_list()
pr_err("PDR: %s get domain list
txn wait failed: %d\n",
req->service_name,
ret);
Timeout error log due to deadlock:
"
PDR: tms/servreg get domain list txn wait failed: -110
PDR: service lookup for msm/adsp/sensor_pd:tms/servreg failed: -110
"
Thanks to Bjorn and Johan for letting me know that this commit also fixes
an audio regression when using the in-kernel pd-mapper as that makes it
easier to hit this race. [1]
Link: https://lore.kernel.org/lkml/Zqet8iInnDhnxkT9@hovoldconsulting.com/ # [1]
Fixes: fbe639b44a ("soc: qcom: Introduce Protection Domain Restart helpers")
CC: stable@vger.kernel.org
Reviewed-by: Bjorn Andersson <bjorn.andersson@oss.qualcomm.com>
Tested-by: Bjorn Andersson <bjorn.andersson@oss.qualcomm.com>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Saranya R <quic_sarar@quicinc.com>
Co-developed-by: Mukesh Ojha <mukesh.ojha@oss.qualcomm.com>
Signed-off-by: Mukesh Ojha <mukesh.ojha@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250212163720.1577876-1-mukesh.ojha@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Include mod_devicetable.h for the 'struct of_device_id' and
clk-provider.h for the 'struct clk_hw'.
Reviewed-by: Taniya Das <quic_tdas@quicinc.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250212-b4-clk-qcom-clean-v3-3-499f37444f5d@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Drivers should include only headers they use so drop:
1. of.h and of_address.h: When no OF call is used (of_device_id is
coming from mod_devicetable.h).
2. clk.h, property.h and reset-controller.h: No calls to clock consumer
or reset framework, no fwnode/property calls.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250212-b4-clk-qcom-clean-v3-2-499f37444f5d@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
If regmap_read() fails, random stack value was used in calculating new
frequency in recalc_rate() callbacks. Such failure is really not
expected as these are all MMIO reads, however code should be here
correct and bail out. This also avoids possible warning on
uninitialized value.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250212-b4-clk-qcom-clean-v3-1-499f37444f5d@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
It is generally expected that the write() function should return a
positive value indicating the number of bytes written or a negative
error code if an error occurs. Returning 0 is unusual and can lead
to unexpected behavior.
When the user program writes the same value to wedged_mode twice in
a row, a lockup will occur, because the value expected to be
returned by the write() function inside the program should be equal
to the actual written value instead of 0.
To reproduce the issue:
echo 1 > /sys/kernel/debug/dri/0/wedged_mode
echo 1 > /sys/kernel/debug/dri/0/wedged_mode <- lockup here
Signed-off-by: Xin Wang <x.wang@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Fei Yang <fei.yang@intel.com>
Cc: Shuicheng Lin <shuicheng.lin@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250213223615.2327367-1-x.wang@intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Now that the binary stats cache infrastructure is largely scope agnostic,
add support for vCPU-scoped stats. Like VM stats, open and cache the
stats FD when the vCPU is created so that it's guaranteed to be valid when
vcpu_get_stats() is invoked.
Account for the extra per-vCPU file descriptor in kvm_set_files_rlimit(),
so that tests that create large VMs don't run afoul of resource limits.
To sanity check that the infrastructure actually works, and to get a bit
of bonus coverage, add an assert in x86's xapic_ipi_test to verify that
the number of HLTs executed by the test matches the number of HLT exits
observed by KVM.
Tested-by: Manali Shukla <Manali.Shukla@amd.com>
Link: https://lore.kernel.org/r/20250111005049.1247555-9-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
Move the max vCPUs test's RLIMIT_NOFILE adjustments to common code, and
use the new helper to adjust the resource limit for non-barebones VMs by
default. x86's recalc_apic_map_test creates 512 vCPUs, and a future
change will open the binary stats fd for all vCPUs, which will put the
recalc APIC test above some distros' default limit of 1024.
Link: https://lore.kernel.org/r/20250111005049.1247555-8-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
Get and cache a VM's binary stats FD when the VM is opened, as opposed to
waiting until the stats are first used. Opening the stats FD outside of
__vm_get_stat() will allow converting it to a scope-agnostic helper.
Note, this doesn't interfere with kvm_binary_stats_test's testcase that
verifies a stats FD can be used after its own VM's FD is closed, as the
cached FD is also closed during kvm_vm_free().
Link: https://lore.kernel.org/r/20250111005049.1247555-7-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
Add a struct and helpers to manage the binary stats cache, which is
currently used only for VM-scoped stats. This will allow expanding the
selftests infrastructure to provide support for vCPU-scoped binary stats,
which, except for the ioctl to get the stats FD are identical to VM-scoped
stats.
Defer converting __vm_get_stat() to a scope-agnostic helper to a future
patch, as getting the stats FD from KVM needs to be moved elsewhere
before it can be made completely scope-agnostic.
Link: https://lore.kernel.org/r/20250111005049.1247555-6-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
Turn vm_get_stat() into a macro that generates a string for the stat name,
as opposed to taking a string. This will allow hardening stat usage in
the future to generate errors on unknown stats at compile time.
No functional change intended.
Link: https://lore.kernel.org/r/20250111005049.1247555-5-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
Fail the test if it attempts to read a stat that doesn't exist, e.g. due
to a typo (hooray, strings), or because the test tried to get a stat for
the wrong scope. As is, there's no indiciation of failure and @data is
left untouched, e.g. holds '0' or random stack data in most cases.
Fixes: 8448ec5993 ("KVM: selftests: Add NX huge pages test")
Link: https://lore.kernel.org/r/20250111005049.1247555-4-seanjc@google.com
[sean: fixup spelling mistake, courtesy of Colin Ian King]
Signed-off-by: Sean Christopherson <seanjc@google.com>
In case we have to retry the loop, we are missing to unlock+put the
folio. In that case, we will keep failing make_device_exclusive_range()
because we cannot grab the folio lock, and even return from the function
with the folio locked and referenced, effectively never succeeding the
make_device_exclusive_range().
While at it, convert the other unlock+put to use a folio as well.
This was found by code inspection.
Fixes: 8f187163eb ("nouveau/svm: implement atomic SVM access")
Signed-off-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Alistair Popple <apopple@nvidia.com>
Tested-by: Alistair Popple <apopple@nvidia.com>
Signed-off-by: Danilo Krummrich <dakr@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20250124181524.3584236-2-david@redhat.com
OP-TEE supplicant is a user-space daemon and it's possible for it
be hung or crashed or killed in the middle of processing an OP-TEE
RPC call. It becomes more complicated when there is incorrect shutdown
ordering of the supplicant process vs the OP-TEE client application which
can eventually lead to system hang-up waiting for the closure of the
client application.
Allow the client process waiting in kernel for supplicant response to
be killed rather than indefinitely waiting in an unkillable state. Also,
a normal uninterruptible wait should not have resulted in the hung-task
watchdog getting triggered, but the endless loop would.
This fixes issues observed during system reboot/shutdown when supplicant
got hung for some reason or gets crashed/killed which lead to client
getting hung in an unkillable state. It in turn lead to system being in
hung up state requiring hard power off/on to recover.
Fixes: 4fb0a5eb36 ("tee: add OP-TEE driver")
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Cc: stable@vger.kernel.org
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Jens Wiklander <jens.wiklander@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
CZ.NIC's Turris devices are based on Marvell EBU SoCs. Hence add a
dependency on ARCH_MVEBU, to prevent asking the user about these drivers
when configuring a kernel that cannot run on an affected CZ.NIC Turris
system.
Fixes: 992f1a3d4e ("platform: cznic: Add preliminary support for Turris Omnia MCU")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The i.MX System Controller Management Interface firmware is only present
on Freescale i.MX SoCs. Hence add a dependency on ARCH_MXC, to prevent
asking the user about this driver when configuring a kernel without
Freescale i.MX platform support.
Fixes: 514b2262ad ("firmware: arm_scmi: Fix i.MX build dependency")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Sven and I have agreed to share the maintainership for the ARM/APPLE
platform after Marcan's step down. I'm handling the downstream Asahi
Linux tree since April 2024 and worked on or wrote several drivers for
the platform.
Signed-off-by: Janne Grunau <j@jannau.net>
Acked-by: Sven Peter <sven@svenpeter.dev>
Acked-by: Hector Martin <marcan@marcan.st>
Acked-by: Neal Gompa <neal@gompa.dev>
Link: https://lore.kernel.org/r/20250208-maint-soc-apple-v1-1-a7f7337baec0@jannau.net
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
some board-level fixes for wrong pins, pinctrl and regulators, and
disabling DMA on a board where the DMA+uart causes the dma controller to
hang, as well as improved network stability for the OrangePi R1.
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEE7v+35S2Q1vLNA3Lx86Z5yZzRHYEFAmeuYTMQHGhlaWtvQHNu
dGVjaC5kZQAKCRDzpnnJnNEdgVmzCACPCxqeyPyHkVhldxnFXcP3mt9GFDKRpi9c
xfv94S3S0pvfiv9a86vpWT/JDOJ1rx3KXKEMuHW1CBpTcRsvKhmDbDeVPeEFm+Wv
Mw7FuE3K+Faa/RHZ8C/8nruIBhg9rrESb/rvXfbUfRLyZhLJ0VJMNoUABp/Q7UxV
2QLvjCQt6J0AqAlbGbDXXyZOtwtk2ZEsYH4soW808avRcpoPPsppK2wCxndG1DEY
wk2Q/lnXzKYa+u9UuQkqrDFzCpMmQfYwPZQkyHVN+Wb7DdsPbgkoOG63nWjZ5SBb
tk+yhB0JWS3uySy4V56VM36DK3r4VBsFzbFid5apeGQEzhDzq0qN
=Pah3
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEiK/NIGsWEZVxh/FrYKtH/8kJUicFAmevTYIACgkQYKtH/8kJ
UicLMxAAiJXDDOBEqUtCmJ4137YEuFWZabj6Bj40K0xJsYNAY9Lz8gokU9IqRl1Y
fsba/drV7g7K7k955QKC99DKq0jT/X1KUALr27U2GyxUoqvlNnxiP4djiAcRGh/v
dpfWy2zi1BMCMCAzLWO8YA60b0zxJBwqd0Jw38ybzCjAk7HmLq2lmeBAF1t9aQgf
ZWJis5/1NpRBy4kHJK9uuDq03Ow9v+jFhRcZsI+j3znK6hzFZN6g79icgbCnP3fQ
iv/SdDGq5HPGE4xtl6BV10TtVnHzS/brR6RR5ck0tNcpdcq+Tbm+SGvvewJOzIAI
SL65m9icTJGeS0Zm/GOmlSvlr1+xhJZGmVwdBrMnxUQo9Pkp32fvAQAw7h6FDy/P
GSYgVzkVOEdv5R/gdJJy8ErfEzXEGRMlgATMSraIulK3LMBhBz4qaUhqQ7fCB/QR
gEfg7W0InLfp5iiISVpv/+cOSqv9SzvX+JeQEL8fMM5J7NW//FsDBvooKQiaAvUa
17E0yr0ZxJD5bzzYJqSPykqn9gTYy5Y/0UyJmZAJpYQ1i0obOwYv0urRD1gppq0D
C4sSZcudZZtlOpqBKeciLSYZc0fYpB3vMu87mRi4pIEbtExKfBVpmN4cON+ox0KI
ZUX+i4pAVFtV6kQ+DkGgFXahFXAi0uKjrkxLQteZplqWyrZVD90=
=AKD2
-----END PGP SIGNATURE-----
Merge tag 'v6.14-rockchip-dtsfixes1' of https://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into HEAD
Fixes for the IOMMU used together with the PCIe controllers on rk3588,
some board-level fixes for wrong pins, pinctrl and regulators, and
disabling DMA on a board where the DMA+uart causes the dma controller to
hang, as well as improved network stability for the OrangePi R1.
* tag 'v6.14-rockchip-dtsfixes1' of https://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
arm64: dts: rockchip: adjust SMMU interrupt type on rk3588
arm64: dts: rockchip: disable IOMMU when running rk3588 in PCIe endpoint mode
dt-bindings: rockchip: pmu: Ensure all properties are defined
arm64: dts: rockchip: Fix lcdpwr_en pin for Cool Pi GenBook
arm64: dts: rockchip: fix fixed-regulator renames on rk3399-gru devices
arm64: dts: rockchip: Disable DMA for uart5 on px30-ringneck
arm64: dts: rockchip: Move uart5 pin configuration to px30 ringneck SoM
arm64: dts: rockchip: change eth phy mode to rgmii-id for orangepi r1 plus lts
arm64: dts: rockchip: Fix broken tsadc pinctrl names for rk3588
Link: https://lore.kernel.org/r/3004814.3ZeAukHxDK@diego
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The Microchip LAN966X SerDes PHY is only present on Microchip LAN966x
SoCs. However, when used as a PCI endpoint, all peripherals of the
LAN966x SoC can be accessed by the PCI host. Hence add dependencies on
SOC_LAN966 and MCHP_LAN966X_PCI, to prevent asking the user about this
driver when configuring a kernel without Microchip LAN966x SoC and PCIe
support.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Herve Codina <herve.codina@bootlin.com>
Link: https://lore.kernel.org/r/369233dfded88ff6fb342e03794fe31985d84d82.1737383314.git.geert+renesas@glider.be
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Observed VBUS_OVERRIDE & ID_OVERRIDE might be programmed
with unexpected value prior to XUSB PADCTL driver, this
could also occur in virtualization scenario.
For example, UEFI firmware programs ID_OVERRIDE=GROUNDED to set
a type-c port to host mode and keeps the value to kernel.
If the type-c port is connected a usb host, below errors can be
observed right after usb host mode driver gets probed. The errors
would keep until usb role class driver detects the type-c port
as device mode and notifies usb device mode driver to set both
ID_OVERRIDE and VBUS_OVERRIDE to correct value by XUSB PADCTL
driver.
[ 173.765814] usb usb3-port2: Cannot enable. Maybe the USB cable is bad?
[ 173.765837] usb usb3-port2: config error
Taking virtualization into account, asserting XUSB PADCTL
reset would break XUSB functions used by other guest OS,
hence only reset VBUS & ID OVERRIDE of the port in
utmi_phy_init.
Fixes: bbf711682c ("phy: tegra: xusb: Add Tegra186 support")
Cc: stable@vger.kernel.org
Change-Id: Ic63058d4d49b4a1f8f9ab313196e20ad131cc591
Signed-off-by: BH Hsieh <bhsieh@nvidia.com>
Signed-off-by: Henry Lin <henryl@nvidia.com>
Link: https://lore.kernel.org/r/20250122105943.8057-1-henryl@nvidia.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The syscon helper device_node_to_regmap() is used to fetch a regmap
registered to a device node. It also currently creates this regmap
if the node did not already have a regmap associated with it. This
should only be used on "syscon" nodes. This driver is not such a
device and instead uses device_node_to_regmap() on its own node as
a hacky way to create a regmap for itself.
This will not work going forward and so we should create our regmap
the normal way by defining our regmap_config, fetching our memory
resource, then using the normal regmap_init_mmio() function.
Signed-off-by: Andrew Davis <afd@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20250123182234.597665-1-afd@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
We currently don't gate the power to the SS phy in phy_exit().
Shuffle the code slightly to ensure the power is gated to the SS phy as
well.
Fixes: 32267c29bc ("phy: exynos5-usbdrd: support Exynos USBDRD 3.1 combo phy (HS & SS)")
CC: stable@vger.kernel.org # 6.11+
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Link: https://lore.kernel.org/r/20241205-gs101-usb-phy-fix-v4-1-0278809fb810@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The i.MX95 USB3 phy has a Type-C Assist block (TCA). This block consists
two functional blocks (XBar assist and VBus assist) and one system
access interface using APB.
The primary functionality of XBar assist is:
- switching lane for flip
- moving unused lanes into lower power states.
This info can be get from:
i.MX95 RM Chapter 163.3.8 Type-C assist (TCA) block.
This will add support for TCA block to achieve lane switching and tca
lower power functionality.
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Reviewed-by: Jun Li <jun.li@nxp.com>
Link: https://lore.kernel.org/r/20241204050907.1081781-1-xu.yang_2@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>