SG2044 and SG2042 have similar SPI-NOR flash controller design,
but have incompatibility which causes existing driver
not working on SG2042:
1. SPI-NOR flash controller on SG2042 have no OPT register.
2. FIFO trigger level on SG2042 should be strictly less than 8.
So introduce a new configurable chip_info structure to hold the
different configuration.
Link: https://github.com/sophgo/sophgo-doc/blob/main/SG2042/TRM/source/SPI-flash.rst
Signed-off-by: Zixian Zeng <sycamoremoon376@gmail.com>
Reviewed-by: Chen Wang <unicorn_wang@outlook.com> & Tested-by: Chen Wang
Link: https://patch.msgid.link/20250720-sfg-spifmc-v4-2-033188ad801e@gmail.com
Reviewed-by: Chen Wang <unicorn_wang@outlook.com> & Tested-by: Chen Wang
Signed-off-by: Mark Brown <broonie@kernel.org>
With further testing, directly using the spi-sg2044-nor driver on SG2042
does not work. SG2042 is found to lack full compatibility with SG2044.
SG2044 has OPT register and it's necessary to write but SG2042 does not.
Due to other possible hardware detail differences, it is better
to bind SG2042 independently.
Fixes: 8450f1e0d3 ("spi: dt-bindings: spi-sg2044-nor: Add SOPHGO SG2042")
Signed-off-by: Zixian Zeng <sycamoremoon376@gmail.com>
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Reviewed-by: Chen Wang <unicorn_wang@outlook.com> & Tested-by: Chen Wang
Link: https://patch.msgid.link/20250720-sfg-spifmc-v4-1-033188ad801e@gmail.com
Reviewed-by: Chen Wang <unicorn_wang@outlook.com> & Tested-by: Chen Wang
Signed-off-by: Mark Brown <broonie@kernel.org>
Many of the DisCo properties that specify Control values have an
additional variant that specifies a separate value for each Control
Number. Add support for these.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/20250718135432.1048566-3-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The current regmap readable/writeable helper functions always
allow the Next flag and allows any Control Number. Mask the Next
flag based on SDCA_ACCESS_MODE_DUAL which is the only Mode that
supports it. Also check that the Control Number is valid for
the given control.
Fixes: e3f7caf74b ("ASoC: SDCA: Add generic regmap SDCA helpers")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/20250718135432.1048566-2-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch supports to readahead more blocks in erofs_readdir(), it can
enhance readdir performance in large direcotry.
readdir test in a large directory which contains 12000 sub-files.
files_per_second
Before: 926385.54
After: 2380435.562
Meanwhile, let's introduces a new sysfs entry to control readahead
bytes to provide more flexible policy for readahead of readdir().
- location: /sys/fs/erofs/<disk>/dir_ra_bytes
- default value: 16384
- disable readahead: set the value to 0
Signed-off-by: Chao Yu <chao@kernel.org>
Reviewed-by: Gao Xiang <hsiangkao@linux.alibaba.com>
Link: https://lore.kernel.org/r/20250721021352.2495371-1-chao@kernel.org
[ Gao Xiang: minor styling adjustment. ]
Signed-off-by: Gao Xiang <hsiangkao@linux.alibaba.com>
Thanks to the meta buffer infrastructure, metadata-compressed inodes are
just read from the metabox inode instead of the blockdevice (or backing
file) inode.
The same is true for shared extended attributes.
When metadata compression is enabled, inode numbers are divided from
on-disk NIDs because of non-LTS 32-bit application compatibility.
Co-developed-by: Gao Xiang <hsiangkao@linux.alibaba.com>
Signed-off-by: Bo Liu (OpenAnolis) <liubo03@inspur.com>
Acked-by: Chao Yu <chao@kernel.org>
Signed-off-by: Gao Xiang <hsiangkao@linux.alibaba.com>
Link: https://lore.kernel.org/r/20250722003229.2121752-1-hsiangkao@linux.alibaba.com
Filesystem metadata has a high degree of redundancy, so it should
compress well in the general case.
Although metadata compression can increase overall I/O latency, many
users care more about minimized image sizes than extreme runtime
performance. Let's implement metadata compression in response to user
requests [1].
Actually, it's quite simple to implement metadata compression: since
EROFS already supports per-inode compression, we can simply treat a
special inode (called `the metabox inode`) as a container for compressed
inode metadata. Since EROFS supports multiple algorithms, users can
even specify LZ4 for metadata and LZMA for data.
To better support incremental builds, the MSB of NIDs indicates where
the inode metadata is located: if bit 63 is set, the inode itself should
be read from `the metabox inode`.
Optionally, shared xattrs can also be kept in `the metabox inode` if
COMPAT_SHARED_EA_IN_METABOX is set.
[1] https://issues.redhat.com/browse/RHEL-75783
Signed-off-by: Gao Xiang <hsiangkao@linux.alibaba.com>
Acked-by: Chao Yu <chao@kernel.org>
Link: https://lore.kernel.org/r/20250717070804.1446345-2-hsiangkao@linux.alibaba.com
There is no need to keep additional local metabufs since we already
have one in `struct erofs_map_blocks`.
This was actually a leftover when applying meta buffers to zmap
operations, see commit 09c543798c ("erofs: use meta buffers for
zmap operations").
Signed-off-by: Gao Xiang <hsiangkao@linux.alibaba.com>
Link: https://lore.kernel.org/r/20250716064152.3537457-1-hsiangkao@linux.alibaba.com
- need_kmap is always true except for a ztailpacking case; thus, just
open-code that one;
- The upcoming metadata compression will add a new boolean, so simplify
this first.
Signed-off-by: Gao Xiang <hsiangkao@linux.alibaba.com>
Reviewed-by: Chao Yu <chao@kernel.org>
Link: https://lore.kernel.org/r/20250714090907.4095645-1-hsiangkao@linux.alibaba.com
The compressed data for the ztailpacking feature is fetched from
the metadata inode (e.g., bd_inode), which is folio-based.
Therefore, the folio interface should be used instead.
Signed-off-by: Gao Xiang <hsiangkao@linux.alibaba.com>
Link: https://lore.kernel.org/r/20250626085459.339830-1-hsiangkao@linux.alibaba.com
-----BEGIN PGP SIGNATURE-----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=bazF
-----END PGP SIGNATURE-----
Merge tag 'ib-mfd-gpio-power-soc-v6.17' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd into gpio/for-next
Immutable branch between MFD, GPIO, Power and SoC due for the v6.17 merge window
Here's a new modem device id.
This has been in linux-next with no reported issues.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCaIIDiwAKCRALxc3C7H1l
CGspAP9JWbxqxUkjVL1SbDo33GkPpFzvgChd/T3c9aQFVzbhKgEA8aiBRjj8SW6D
D7LnACK+zJ3QnxKAgLOAU46H5+UXzQY=
=eFS2
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-6.17-rc1-2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB serial device id for 6.17-rc1
Here's a new modem device id.
This has been in linux-next with no reported issues.
* tag 'usb-serial-6.17-rc1-2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: option: add Foxconn T99W709
Here are the USB serial updates for 6.17-rc1, including
- switch to new gpiolib interface that can return errors
All have been in linux-next with no reported issues.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCaIICfQAKCRALxc3C7H1l
CHV4AQCvorLSquAZcYd//Ytx7p8p26TTG1fYHsxiLeyCdBqcLQD/YPMNoJrKTRBL
in3L3/ldbBrGr6vI8cTvQYVmlWtJ/w4=
=NGRU
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-6.17-rc1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB serial updates for 6.17-rc1
Here are the USB serial updates for 6.17-rc1, including
- switch to new gpiolib interface that can return errors
All have been in linux-next with no reported issues.
* tag 'usb-serial-6.17-rc1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: cp210x: use new GPIO line value setter callbacks
USB: serial: ftdi_sio: use new GPIO line value setter callbacks
-----BEGIN PGP SIGNATURE-----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=MBQn
-----END PGP SIGNATURE-----
Merge tag 'ipsec-2025-07-23' of git://git.kernel.org/pub/scm/linux/kernel/git/klassert/ipsec
Steffen Klassert says:
====================
pull request (net): ipsec 2025-07-23
1) Premption fixes for xfrm_state_find.
From Sabrina Dubroca.
2) Initialize offload path also for SW IPsec GRO. This fixes a
performance regression on SW IPsec offload.
From Leon Romanovsky.
3) Fix IPsec UDP GRO for IKE packets.
From Tobias Brunner,
4) Fix transport header setting for IPcomp after decompressing.
From Fernando Fernandez Mancera.
5) Fix use-after-free when xfrmi_changelink tries to change
collect_md for a xfrm interface.
From Eyal Birger .
6) Delete the special IPcomp x->tunnel state along with the state x
to avoid refcount problems.
From Sabrina Dubroca.
Please pull or let me know if there are problems.
* tag 'ipsec-2025-07-23' of git://git.kernel.org/pub/scm/linux/kernel/git/klassert/ipsec:
Revert "xfrm: destroy xfrm_state synchronously on net exit path"
xfrm: delete x->tunnel as we delete x
xfrm: interface: fix use-after-free after changing collect_md xfrm interface
xfrm: ipcomp: adjust transport header after decompressing
xfrm: Set transport header to fix UDP GRO handling
xfrm: always initialize offload path
xfrm: state: use a consistent pcpu_id in xfrm_state_find
xfrm: state: initialize state_ptrs earlier in xfrm_state_find
====================
Link: https://patch.msgid.link/20250723075417.3432644-1-steffen.klassert@secunet.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Do not use "mtk-pmic-keys" when creating sub-device for the keypad to
make sure the keypad driver will only bind to the sub-device if it has
support for the variant/has matching compatible.
Cc: stable@vger.kernel.org
Fixes: 6e31bb8d3a ("mfd: mt6397: Add initial support for MT6328")
Fixes: de58cee8c6 ("mfd: mt6397-core: Add MT6357 PMIC support")
Fixes: 4a901e3050 ("mfd: mt6397-core: Add resources for PMIC keys for MT6359")
Reported-by: Louis-Alexis Eyraud <louisalexis.eyraud@collabora.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Tested-by: Louis-Alexis Eyraud <louisalexis.eyraud@collabora.com> # on
Link: https://lore.kernel.org/r/r4k3pgd3ew3ypne7ernxuzwgniiyvzosbce4cfajbcu7equblt@yato35tjb3lw
Signed-off-by: Lee Jones <lee@kernel.org>
Originally an explicit ID for the AXP313/AXP323 regulator was set to
avoid a conflict with the primary AXP717 PMIC on Allwinner A523 family
boards.
This didn't entirely work since on some or all of these boards, the
interrupt line on this secondary PMIC was left unconnected, and thus
the driver would fall back to the generic "no interrupt; only regulators"
case, which didn't have the explicit ID set, thus undoing the intended
fix.
Also set an explicit ID for the regulator cell in the no IRQ generic
fall back case. This fixes the conflict for the AXP717 + AXP313/AXP323
case. For the actual single PMIC with no IRQ connected case, the ID does
not affect functionality, only the device naming of the regulator cell,
and by extension the name and path under sysfs.
Fixes: 249abf9b1e25 ("mfd: axp20x: Set explicit ID for AXP313 regulator")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20250701163652.252010-1-wens@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
The RK806 PMIC has a bitfield for configuring the restart/reset behavior
(which I assume Rockchip calls "function") whenever the PMIC is reset
either programmatically (c.f. DEV_RST in the datasheet) or via PWRCTRL
or RESETB pins.
For RK806, the following values are possible for RST_FUN:
0b00 means "Restart PMU"
0b01 means "Reset all the power off reset registers, forcing
the state to switch to ACTIVE mode"
0b10 means "Reset all the power off reset registers, forcing
the state to switch to ACTIVE mode, and simultaneously
pull down the RESETB PIN for 5mS before releasing"
0b11 means the same as for 0b10 just above.
This adds the appropriate logic in the driver to parse the new
rockchip,reset-mode DT property to pass this information. It just
happens that the values in the binding match the values to write in the
bitfield so no mapping is necessary.
If it is missing, the register is left untouched and relies either on
the silicon default or on whatever was set earlier in the boot stages
(e.g. the bootloader).
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Link: https://lore.kernel.org/r/20250627-rk8xx-rst-fun-v4-2-ce05d041b45f@cherry.de
Signed-off-by: Lee Jones <lee@kernel.org>
The RK806 PMIC allows to configure its reset/restart behavior whenever
the PMIC is reset either programmatically or via some external pins
(e.g. PWRCTRL or RESETB).
The following modes exist:
- 0; restart PMU,
- 1; reset all power off reset registers and force state to switch to
ACTIVE mode,
- 2; same as mode 1 and also pull RESETB pin down for 5ms,
For example, some hardware may require a full restart (mode 0) in order
to function properly as regulators are shortly interrupted in this mode.
This is the case for RK3588 Jaguar and RK3588 Tiger which have a
companion microcontroller running on an independent power supply and
monitoring the PMIC power rail to know the state of the main system.
When it detects a restart, it resets its own IPs exposed to the main
system as if to simulate its own reset. Failing to perform this fake
reset of the microcontroller may break things (e.g. watchdog not
automatically disabled, buzzer still running until manually disabled,
leftover configuration from previous main system state, etc...).
Some other systems may be depending on the power rails to not be
interrupted even for a small amount of time[1].
This allows to specify how the PMIC should perform on the hardware level
and may differ between hardware designs, so a DT property seems
warranted. I unfortunately do not see how this could be made generic
enough to make it a non-vendor property.
[1] https://lore.kernel.org/linux-rockchip/2577051.irdbgypaU6@workhorse/
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: "Rob Herring (Arm)" <robh@kernel.org>
Link: https://lore.kernel.org/r/20250627-rk8xx-rst-fun-v4-1-ce05d041b45f@cherry.de
Signed-off-by: Lee Jones <lee@kernel.org>
Update header inclusions to follow IWYU (Include What You Use)
principle.
Note that kernel.h is discouraged to be included as it's written
at the top of that file.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20250627164414.1043434-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Lee Jones <lee@kernel.org>
Update header inclusions to follow IWYU (Include What You Use)
principle.
Note that kernel.h is discouraged to be included as it's written
at the top of that file.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20250626154544.324724-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Lee Jones <lee@kernel.org>
Update header inclusions to follow IWYU (Include What You Use)
principle.
Note that kernel.h is discouraged to be included as it's written
at the top of that file.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20250626155951.325683-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Lee Jones <lee@kernel.org>
Document why the binding uses oneOf when specifying just one of the
interrupt properties is supposed to be enough.
dtschema's fixups.py has special treatment of the interrupts and
interrupts-extended properties, but that appears to work at the top
level only. Elsewhere, an explicit oneOf is required.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250627-s2mpg10-binding-comment-v1-1-f37e5187f0fd@linaro.org
Signed-off-by: Lee Jones <lee@kernel.org>
Update header inclusions to follow IWYU (Include What You Use)
principle.
Note that kernel.h is discouraged to be included as it's written
at the top of that file.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20250626154354.324439-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Lee Jones <lee@kernel.org>
'struct regmap_irq_sub_irq_map' and 'struct tps65219_chip_data' are not
modified in this driver.
Constifying these structures moves some data to a read-only section, so
increases overall security.
On a x86_64, with allmodconfig:
Before:
======
text data bss dec hex filename
27804 10016 256 38076 94bc drivers/mfd/tps65219.o
After:
=====
text data bss dec hex filename
27893 9792 256 37941 9435 drivers/mfd/tps65219.o
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/117946696551de41b706ea9b973a7ccaacea5178.1750530460.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Lee Jones <lee@kernel.org>
Several structures are not modified in this driver. Constifying them moves
some data to a read-only section, so increases overall security, especially
when the structure holds some function pointers. This is the case for
'gpio_keys_platform_data' and 'mfd_cell'.
On a x86_64, with allmodconfig:
Before:
======
text data bss dec hex filename
18321 13952 192 32465 7ed1 drivers/mfd/rohm-bd71828.o
After:
=====
text data bss dec hex filename
22897 9376 192 32465 7ed1 drivers/mfd/rohm-bd71828.o
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Matti Vaittinen <mazziesaccount@gmail.com>
Link: https://lore.kernel.org/r/037e28e587ae899da9acdb45c606d75ec61f858b.1750501700.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Lee Jones <lee@kernel.org>
commit b0a5cde57c ("dt-bindings: mfd: Explain lack of child dependency
in simple-mfd") pointed out that it's a mistake for a child device of
a simple MFD device to depend on the simple MFD device's clock resources.
fsl,imx8qxp-csr.yaml happens to make that mistake. To fix that, remove
fsl,imx8qxp-csr.yaml and use "simple-pm-bus" and "syscon" as the CSR node's
compatible strings in the examples of fsl,imx8qxp-pixel-link-msi-bus.yaml
to replace the wrong compatible strings which include "simple-mfd" and
"fsl,imx8qxp-mipi-lvds-csr". Since fsl,imx8qxp-pixel-link-msi-bus.yaml
as the last user of the CSR compatible strings no longer uses them, it's
safe to remove the fsl,imx8qxp-csr.yaml binding documentation.
Fixes: 9b2c55b540 ("dt-bindings: mfd: Add i.MX8qm/qxp Control and Status Registers module binding")
Fixes: c08645ea21 ("dt-bindings: bus: Add Freescale i.MX8qxp pixel link MSI bus binding")
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20250620022537.3072877-1-victor.liu@nxp.com
Signed-off-by: Lee Jones <lee@kernel.org>
On newer boards featuring the A523 SoC, the AXP323 (related to the
AXP313) is paired with the AXP717 and serves as a secondary PMIC
providing additional regulator outputs. However the MFD cells are all
registered with PLATFORM_DEVID_NONE, which causes the regulator cells
to conflict with each other.
Commit e37ec32188 ("mfd: axp20x: Allow multiple regulators") attempted
to fix this by switching to PLATFORM_DEVID_AUTO so that the device names
would all be different, however that broke IIO channel mapping, which is
also tied to the device names. As a result the change was later reverted.
Instead, here we attempt to make sure the AXP313/AXP323 regulator cell
does not conflict by explicitly giving it an ID number. This was
previously done for the AXP809+AXP806 pair used with the A80 SoC.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20250619173207.3367126-1-wens@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
irq_domain_create_simple() takes fwnode as the first argument. It can be
extracted from the struct device using dev_fwnode() helper instead of
using of_node with of_fwnode_handle().
So use the dev_fwnode() helper.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20250611104348.192092-13-jirislaby@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
After commit a934a57a42 ("scripts/misc-check: check missing #include
<linux/export.h> when W=1") and commit 7d95680d64 ("scripts/misc-check:
check unnecessary #include <linux/export.h> when W=1") we get the build
warning with W=1:
drivers/mfd/stm32-timers.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
Fix it.
Signed-off-by: Antonio Borneo <antonio.borneo@foss.st.com>
Acked-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Link: https://lore.kernel.org/r/20250610124855.269158-6-antonio.borneo@foss.st.com
Signed-off-by: Lee Jones <lee@kernel.org>
twl6030_mmc_card_detect() and twl6030_mmc_card_detect_config() have been
unused since 2013's commit b2ff479061 ("ARM: OMAP2+: Remove legacy
omap4_twl6030_hsmmc_init")
Remove them.
Signed-off-by: "Dr. David Alan Gilbert" <linux@treblig.org>
Link: https://lore.kernel.org/r/20250607202232.265344-1-linux@treblig.org
Signed-off-by: Lee Jones <lee@kernel.org>
Combine the following separate plain text based bindings to YAML:
lpc1850-creg-clk.txt
pc1850-dmamux.txt
phy-lpc18xx-usb-otg.txt
Additional changes:
- remove label in example.
- remove dmamux consumer in example.
- remove clock consumer in example.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: "Rob Herring (Arm)" <robh@kernel.org>
Link: https://lore.kernel.org/r/20250602143612.943516-1-Frank.Li@nxp.com
Signed-off-by: Lee Jones <lee@kernel.org>
Convert the Freescale MXS Low-Resoulution ADC (LRADC) device tree
binding documentation to json-schema.
The clocks and #io-channel-cells properties have also been added; They
are present in the respective SoC DTSI files but were missing from the
old mxs-lradc.txt file.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20250530160748.2476088-2-dario.binacchi@amarulasolutions.com
Signed-off-by: Lee Jones <lee@kernel.org>
Static 'struct reg_sequence' array, 'struct regmap_irq_sub_irq_map' and
'struct regmap_irq_chip ' are not modified so can be changed to const
for more safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Matti Vaittinen <mazziesaccount@gmail.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20250528194416.567127-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Lee Jones <lee@kernel.org>
The charge-control subsystem in the ChromeOS EC is not strictly tied to
its USB-PD subsystem.
Since commit 7613bc0d11 ("mfd: cros_ec: Don't load charger with UCSI")
the presence of EC_FEATURE_UCSI_PPM would inhibit the probing of the
charge-control driver.
Furthermore recent versions of the EC firmware in Framework laptops
hard-disable EC_FEATURE_USB_PD to avoid probing cros-usbpd-charger,
which then also breaks cros-charge-control.
Instead use the dedicated EC_FEATURE_CHARGER.
Cc: stable@vger.kernel.org
Link: 1d7bcf1d50
Fixes: 555b5fcdb8 ("mfd: cros_ec: Register charge control subdevice")
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Tested-by: Tom Vincent <linux@tlvince.com>
Link: https://lore.kernel.org/r/20250521-cros-ec-mfd-chctl-probe-v1-1-6ebfe3a6efa7@weissschuh.net
Signed-off-by: Lee Jones <lee@kernel.org>
* arm/smmu/bindings:
dt-bindings: arm-smmu: Remove sdm845-cheza specific entry
dt-bindings: arm-smmu: document the support on Milos
iommu/arm-smmu-qcom: Add SM6115 MDSS compatible
