Since f916dd32a9 ("arm64/fpsimd: ptrace: Mandate SVE payload for
streaming-mode state") we do not support writing FPSIMD payload data when
writing NT_ARM_SSVE but the sve-ptrace test has an explicit test for
this being supported which was not updated to reflect the new behaviour.
Fix the test to expect a failure when writing FPSIMD data to the
streaming mode register set.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20250609-kselftest-arm64-ssve-fixups-v2-2-998fcfa6f240@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The check that the new vector length we set was the expected one was typoed
to an assignment statement which for some reason the compilers didn't spot,
most likely due to the macros involved.
Fixes: a1d7111257 ("selftests: arm64: More comprehensively test the SVE ptrace interface")
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Dev Jain <dev.jain@arm.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20250609-kselftest-arm64-ssve-fixups-v2-1-998fcfa6f240@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Examples should be complete and should not have a 'status' property,
especially a disabled one because this disables the dt_binding_check of
the example against the schema. Dropping 'status' property shows
missing other properties - phy-mode and phy-handle.
Fixes: 114508a89d ("dt-bindings: net: Add support for Sophgo SG2044 dwmac")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Reviewed-by: Chen Wang <unicorn_wang@outlook.com>
Link: https://patch.msgid.link/20250701063621.23808-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Jiawen Wu says:
====================
Fix IRQ vectors
The interrupt vector order was adjusted by [1]commit 937d46ecc5 ("net:
wangxun: add ethtool_ops for channel number") in Linux-6.8. Because at
that time, the MISC interrupt acts as the parent interrupt in the GPIO
IRQ chip. When the number of Rx/Tx ring changes, the last MISC
interrupt must be reallocated. Then the GPIO interrupt controller would
be corrupted. So the initial plan was to adjust the sequence of the
interrupt vectors, let MISC interrupt to be the first one and do not
free it.
Later, irq_domain was introduced in [2]commit aefd013624 ("net: txgbe:
use irq_domain for interrupt controller") to avoid this problem.
However, the vector sequence adjustment was not reverted. So there is
still one problem that has been left unresolved.
Due to hardware limitations of NGBE, queue IRQs can only be requested
on vector 0 to 7. When the number of queues is set to the maximum 8,
the PCI IRQ vectors are allocated from 0 to 8. The vector 0 is used by
MISC interrupt, and althrough the vector 8 is used by queue interrupt,
it is unable to receive packets. This will cause some packets to be
dropped when RSS is enabled and they are assigned to queue 8.
This patch set fix the above problems.
[1] https://git.kernel.org/netdev/net-next/c/937d46ecc5f9
[2] https://git.kernel.org/netdev/net-next/c/aefd013624a1
====================
Link: https://patch.msgid.link/20250701063030.59340-1-jiawenwu@trustnetic.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
For NGBE devices, the queue number is limited to be 1 when SRIOV is
enabled. In this case, IRQ vector[0] is used for MISC and vector[1] is
used for queue, based on the previous patches. But for the hardware
design, the IRQ vector[1] must be allocated for use by the VF[6] when
the number of VFs is 7. So the IRQ vector[0] should be shared for PF
MISC and QUEUE interrupts.
+-----------+----------------------+
| Vector | Assigned To |
+-----------+----------------------+
| Vector 0 | PF MISC and QUEUE |
| Vector 1 | VF 6 |
| Vector 2 | VF 5 |
| Vector 3 | VF 4 |
| Vector 4 | VF 3 |
| Vector 5 | VF 2 |
| Vector 6 | VF 1 |
| Vector 7 | VF 0 |
+-----------+----------------------+
Minimize code modifications, only adjust the IRQ vector number for this
case.
Fixes: 877253d2cb ("net: ngbe: add sriov function support")
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Larysa Zaremba <larysa.zaremba@intel.com>
Link: https://patch.msgid.link/20250701063030.59340-4-jiawenwu@trustnetic.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Due to hardware limitations of NGBE, queue IRQs can only be requested
on vector 0 to 7. When the number of queues is set to the maximum 8,
the PCI IRQ vectors are allocated from 0 to 8. The vector 0 is used by
MISC interrupt, and althrough the vector 8 is used by queue interrupt,
it is unable to receive packets. This will cause some packets to be
dropped when RSS is enabled and they are assigned to queue 8.
So revert the adjustment of the MISC IRQ location, to make it be the
last one in IRQ vectors.
Fixes: 937d46ecc5 ("net: wangxun: add ethtool_ops for channel number")
Cc: stable@vger.kernel.org
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Larysa Zaremba <larysa.zaremba@intel.com>
Link: https://patch.msgid.link/20250701063030.59340-3-jiawenwu@trustnetic.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Move the creating of irq_domain for MISC IRQ from .probe to .ndo_open,
and free it in .ndo_stop, to maintain consistency with the queue IRQs.
This it for subsequent adjustments to the IRQ vectors.
Fixes: aefd013624 ("net: txgbe: use irq_domain for interrupt controller")
Cc: stable@vger.kernel.org
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Link: https://patch.msgid.link/20250701063030.59340-2-jiawenwu@trustnetic.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Recent work by Thomas Weißschuh means that it is now possible to use
kselftest.h with nolibc. Convert the tpidr2 test which is nolibc specific
to use kselftest.h, making it look more standard and ensuring it gets the
benefit of any work done on kselftest.h.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20250609-kselftest-arm64-nolibc-header-v1-1-16ee1c6fbfed@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Laurent Vivier says:
====================
virtio: Fixes for TX ring sizing and resize error reporting
This patch series contains two fixes and a cleanup for the virtio subsystem.
The first patch fixes an error reporting bug in virtio_ring's
virtqueue_resize() function. Previously, errors from internal resize
helpers could be masked if the subsequent re-enabling of the virtqueue
succeeded. This patch restores the correct error propagation, ensuring that
callers of virtqueue_resize() are properly informed of underlying resize
failures.
The second patch does a cleanup of the use of '2+MAX_SKB_FRAGS'
The third patch addresses a reliability issue in virtio_net where the TX
ring size could be configured too small, potentially leading to
persistently stopped queues and degraded performance. It enforces a
minimum TX ring size to ensure there's always enough space for at least one
maximally-fragmented packet plus an additional slot.
====================
Link: https://patch.msgid.link/20250521092236.661410-1-lvivier@redhat.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The `tx_may_stop()` logic stops TX queues if free descriptors
(`sq->vq->num_free`) fall below the threshold of (`MAX_SKB_FRAGS` + 2).
If the total ring size (`ring_num`) is not strictly greater than this
value, queues can become persistently stopped or stop after minimal
use, severely degrading performance.
A single sk_buff transmission typically requires descriptors for:
- The virtio_net_hdr (1 descriptor)
- The sk_buff's linear data (head) (1 descriptor)
- Paged fragments (up to MAX_SKB_FRAGS descriptors)
This patch enforces that the TX ring size ('ring_num') must be strictly
greater than (MAX_SKB_FRAGS + 2). This ensures that the ring is
always large enough to hold at least one maximally-fragmented packet
plus at least one additional slot.
Reported-by: Lei Yang <leiyang@redhat.com>
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Reviewed-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Link: https://patch.msgid.link/20250521092236.661410-4-lvivier@redhat.com
Tested-by: Lei Yang <leiyang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Improve consistency by using everywhere it is needed
'MAX_SKB_FRAGS + 2' rather than '2+MAX_SKB_FRAGS' or
'2 + MAX_SKB_FRAGS'.
No functional change.
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Reviewed-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Link: https://patch.msgid.link/20250521092236.661410-3-lvivier@redhat.com
Tested-by: Lei Yang <leiyang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The virtqueue_resize() function was not correctly propagating error codes
from its internal resize helper functions, specifically
virtqueue_resize_packet() and virtqueue_resize_split(). If these helpers
returned an error, but the subsequent call to virtqueue_enable_after_reset()
succeeded, the original error from the resize operation would be masked.
Consequently, virtqueue_resize() could incorrectly report success to its
caller despite an underlying resize failure.
This change restores the original code behavior:
if (vdev->config->enable_vq_after_reset(_vq))
return -EBUSY;
return err;
Fix: commit ad48d53b5b ("virtio_ring: separate the logic of reset/enable from virtqueue_resize")
Cc: xuanzhuo@linux.alibaba.com
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Link: https://patch.msgid.link/20250521092236.661410-2-lvivier@redhat.com
Tested-by: Lei Yang <leiyang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Historically KVM hyp code saved the host's FPSIMD state into the hosts's
fpsimd_state memory, and so it was necessary to map this into the hyp
Stage-1 mappings before running a vCPU.
This is no longer necessary as of commits:
* fbc7e61195 ("KVM: arm64: Unconditionally save+flush host FPSIMD/SVE/SME state")
* 8eca7f6d51 ("KVM: arm64: Remove host FPSIMD saving for non-protected KVM")
Since those commits, we eagerly save the host's FPSIMD state before
calling into hyp to run a vCPU, and hyp code never reads nor writes the
host's fpsimd_state memory. There's no longer any need to map the host's
fpsimd_state memory into the hyp Stage-1, and kvm_arch_vcpu_run_map_fp()
is unnecessary but benign.
Remove kvm_arch_vcpu_run_map_fp(). Currently there is no code to perform
a corresponding unmap, and we never mapped the host's SVE or SME state
into the hyp Stage-1, so no other code needs to be removed.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Fuad Tabba <tabba@google.com>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Mark Brown <broonie@kernel.org>
Cc: Oliver Upton <oliver.upton@linux.dev>
Cc: Will Deacon <will@kernel.org>
Cc: kvmarm@lists.linux.dev
Reviewed-by: Mark Brown <broonie@kernel.org>
Tested-by: Fuad Tabba <tabba@google.com>
Reviewed-by: Fuad Tabba <tabba@google.com>
Link: https://lore.kernel.org/r/20250619134817.4075340-1-mark.rutland@arm.com
Signed-off-by: Marc Zyngier <maz@kernel.org>
Booting an EL2 guest on a system only supporting a subset of the
possible page sizes leads to interesting situations.
For example, on a system that only supports 4kB and 64kB, and is
booted with a 4kB kernel, we end-up advertising 16kB support at
stage-2, which is pretty weird.
That's because we consider that any S2 bigger than our base granule
is fair game, irrespective of what the HW actually supports. While this
is not impossible to support (KVM would happily handle it), it is likely
to be confusing for the guest.
Add new checks that will verify that this granule size is actually
supported before publishing it to the guest.
Fixes: e7ef6ed458 ("KVM: arm64: Enforce NV limits on a per-idregs basis")
Reviewed-by: Oliver Upton <oliver.upton@linux.dev>
Signed-off-by: Marc Zyngier <maz@kernel.org>
In probe appletb_kbd_probe() a "struct appletb_kbd *kbd" is allocated
via devm_kzalloc() to store touch bar keyboard related data.
Later on if backlight_device_get_by_name() finds a backlight device
with name "appletb_backlight" a timer (kbd->inactivity_timer) is setup
with appletb_inactivity_timer() and the timer is armed to run after
appletb_tb_dim_timeout (60) seconds.
A use-after-free is triggered when failure occurs after the timer is
armed. This ultimately means probe failure occurs and as a result the
"struct appletb_kbd *kbd" which is device managed memory is freed.
After 60 seconds the timer will have expired and __run_timers will
attempt to access the timer (kbd->inactivity_timer) however the kdb
structure has been freed causing a use-after free.
[ 71.636938] ==================================================================
[ 71.637915] BUG: KASAN: slab-use-after-free in __run_timers+0x7ad/0x890
[ 71.637915] Write of size 8 at addr ffff8881178c5958 by task swapper/1/0
[ 71.637915]
[ 71.637915] CPU: 1 UID: 0 PID: 0 Comm: swapper/1 Not tainted 6.16.0-rc2-00318-g739a6c93cc75-dirty #12 PREEMPT(voluntary)
[ 71.637915] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.2-debian-1.16.2-1 04/01/2014
[ 71.637915] Call Trace:
[ 71.637915] <IRQ>
[ 71.637915] dump_stack_lvl+0x53/0x70
[ 71.637915] print_report+0xce/0x670
[ 71.637915] ? __run_timers+0x7ad/0x890
[ 71.637915] kasan_report+0xce/0x100
[ 71.637915] ? __run_timers+0x7ad/0x890
[ 71.637915] __run_timers+0x7ad/0x890
[ 71.637915] ? __pfx___run_timers+0x10/0x10
[ 71.637915] ? update_process_times+0xfc/0x190
[ 71.637915] ? __pfx_update_process_times+0x10/0x10
[ 71.637915] ? _raw_spin_lock_irq+0x80/0xe0
[ 71.637915] ? _raw_spin_lock_irq+0x80/0xe0
[ 71.637915] ? __pfx__raw_spin_lock_irq+0x10/0x10
[ 71.637915] run_timer_softirq+0x141/0x240
[ 71.637915] ? __pfx_run_timer_softirq+0x10/0x10
[ 71.637915] ? __pfx___hrtimer_run_queues+0x10/0x10
[ 71.637915] ? kvm_clock_get_cycles+0x18/0x30
[ 71.637915] ? ktime_get+0x60/0x140
[ 71.637915] handle_softirqs+0x1b8/0x5c0
[ 71.637915] ? __pfx_handle_softirqs+0x10/0x10
[ 71.637915] irq_exit_rcu+0xaf/0xe0
[ 71.637915] sysvec_apic_timer_interrupt+0x6c/0x80
[ 71.637915] </IRQ>
[ 71.637915]
[ 71.637915] Allocated by task 39:
[ 71.637915] kasan_save_stack+0x33/0x60
[ 71.637915] kasan_save_track+0x14/0x30
[ 71.637915] __kasan_kmalloc+0x8f/0xa0
[ 71.637915] __kmalloc_node_track_caller_noprof+0x195/0x420
[ 71.637915] devm_kmalloc+0x74/0x1e0
[ 71.637915] appletb_kbd_probe+0x37/0x3c0
[ 71.637915] hid_device_probe+0x2d1/0x680
[ 71.637915] really_probe+0x1c3/0x690
[ 71.637915] __driver_probe_device+0x247/0x300
[ 71.637915] driver_probe_device+0x49/0x210
[...]
[ 71.637915]
[ 71.637915] Freed by task 39:
[ 71.637915] kasan_save_stack+0x33/0x60
[ 71.637915] kasan_save_track+0x14/0x30
[ 71.637915] kasan_save_free_info+0x3b/0x60
[ 71.637915] __kasan_slab_free+0x37/0x50
[ 71.637915] kfree+0xcf/0x360
[ 71.637915] devres_release_group+0x1f8/0x3c0
[ 71.637915] hid_device_probe+0x315/0x680
[ 71.637915] really_probe+0x1c3/0x690
[ 71.637915] __driver_probe_device+0x247/0x300
[ 71.637915] driver_probe_device+0x49/0x210
[...]
The root cause of the issue is that the timer is not disarmed
on failure paths leading to it remaining active and accessing
freed memory. To fix this call timer_delete_sync() to deactivate
the timer.
Another small issue is that timer_delete_sync is called
unconditionally in appletb_kbd_remove(), fix this by checking
for a valid kbd->backlight_dev before calling timer_delete_sync.
Fixes: 93a0fc4894 ("HID: hid-appletb-kbd: add support for automatic brightness control while using the touchbar")
Cc: stable@vger.kernel.org
Signed-off-by: Qasim Ijaz <qasdev00@gmail.com>
Reviewed-by: Aditya Garg <gargaditya08@live.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
When calling buf_to_xdp, the len argument is the frame data's length
without virtio header's length (vi->hdr_len). We check that len with
xsk_pool_get_rx_frame_size() + vi->hdr_len
to ensure the provided len does not larger than the allocated chunk
size. The additional vi->hdr_len is because in virtnet_add_recvbuf_xsk,
we use part of XDP_PACKET_HEADROOM for virtio header and ask the vhost
to start placing data from
hard_start + XDP_PACKET_HEADROOM - vi->hdr_len
not
hard_start + XDP_PACKET_HEADROOM
But the first buffer has virtio_header, so the maximum frame's length in
the first buffer can only be
xsk_pool_get_rx_frame_size()
not
xsk_pool_get_rx_frame_size() + vi->hdr_len
like in the current check.
This commit adds an additional argument to buf_to_xdp differentiate
between the first buffer and other ones to correctly calculate the maximum
frame's length.
Cc: stable@vger.kernel.org
Reviewed-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Fixes: a4e7ba7027 ("virtio_net: xsk: rx: support recv small mode")
Signed-off-by: Bui Quang Minh <minhquangbui99@gmail.com>
Link: https://patch.msgid.link/20250630151315.86722-2-minhquangbui99@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Convert the Synopsys Designware Reset Controller binding to schema. It
is a straight forward conversion.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://lore.kernel.org/r/20250702222609.2760718-1-robh@kernel.org
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
The -supply postfix is wrong but wasn't noticed on the CRD devices or
indeed the Dell devices, however on Lenovo devices the error comes up.
Fixes: 1830cf0f56 ("media: qcom: camss: Add x1e80100 specific support")
Cc: stable@vger.kernel.org
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
[bod: reworded commit log per Konrad's feedback]
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
For sake of code simplicity and readability reduce the function code by
one level of indentation, the change is non-functional.
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
[bod: Fixed indentation error]
Signed-off-by: Bryan O'Donoghue <bod@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
A media device can and at least for sake of simplicity should be registered
before V4L2 devices including the ones added on async completion.
The change removes the second and out of camss_probe() media device
registration path, and it allows to get a working ISP media device
independently from connected or not sensor devices.
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Acked-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Bryan O'Donoghue <bod@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
It's sufficient to have just one previously set csiphy_formats_sdm845 data.
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Bryan O'Donoghue <bod@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
A call to media_device_init() requires media_device_cleanup() counterpart
to complete cleanup and release any allocated resources.
This has been done in the driver .remove() right from the beginning, but
error paths on .probe() shall also be fixed.
Fixes: a1d7c116fc ("media: camms: Add core files")
Cc: stable@vger.kernel.org
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Bryan O'Donoghue <bod@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
The moving of init sequence hook from gen2() to subdev_init() doesn't
account for gen1 devices such as SDM660 and SDM670. The switch should find
the right offset for gen2 PHYs only, not reject gen1. Remove the default
error case to restore gen1 CSIPHY support.
Cc: stable@vger.kernel.org
Fixes: fbce0ca24c ("media: qcom: camss: csiphy-3ph: Move CSIPHY variables to data field inside csiphy struct")
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Signed-off-by: Bryan O'Donoghue <bod@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
The libcamera plugin for Pipewire may keep an open file descriptor to
the video device, even while streaming. This simplifies its operation,
as it only needs to keep track of a number instead of a file path. When
the video device is open but not streaming, the pipeline can be powered
off. Move the pipeline power management to the prepare_streaming and
unprepare_streaming functions.
Signed-off-by: Richard Acayan <mailingradian@gmail.com>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Signed-off-by: Bryan O'Donoghue <bod@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
According to the devicetree specification a unit address shall match
the first address value of the reg property.
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Signed-off-by: Bryan O'Donoghue <bod@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Since clock lanes under CSIPHY are hard-wired and non-selectable,
it makes sense to remove this port property.
The change follows the same logic as found in commit 336136e197
("media: dt-bindings: media: camss: Remove clock-lane property").
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Bryan O'Donoghue <bod@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Since CSIPHY IP on modern Qualcomm SoCs supports D-PHY and C-PHY
interfaces, it might be necessary to specify it explicitly for some
particular devices.
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Bryan O'Donoghue <bod@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
There are 4 CSIPHY ports on X1E80100, it'd be preferred to tinker a too
loose the regexp, which covers all these port names.
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Acked-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bryan O'Donoghue <bod@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Pass PD_FLAG_REQUIRED_OPP flag to allow opp framework to scale the rpmpd
power domains.
Signed-off-by: Akhil P Oommen <akhilpo@oss.qualcomm.com>
Reviewed-by: Dikshita Agarwal <quic_dikshita@quicinc.com>
Signed-off-by: Bryan O'Donoghue <bod@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Add a codec specific for the VP9 decoder to ensure that a non-null
buffer is sent to the firmware during drain. The firmware enforces a
check for VP9 decoder that the number of buffers queued and dequeued on
the output plane should match. When a null buffer is sent, the firmware
does not return a response for it, leading to a count mismatch and an
assertion failure from the firmware.
Acked-by: Vikash Garodia <quic_vgarodia@quicinc.com>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-HDK
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-QRD
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-HDK
Signed-off-by: Dikshita Agarwal <quic_dikshita@quicinc.com>
Tested-by: Vikash Garodia <quic_vgarodia@quicinc.com> # on sa8775p-ride
Signed-off-by: Bryan O'Donoghue <bod@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Add internal buffer count and size calculations for HEVC and VP9
decoders.
Acked-by: Vikash Garodia <quic_vgarodia@quicinc.com>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-HDK
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-QRD
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-HDK
Signed-off-by: Dikshita Agarwal <quic_dikshita@quicinc.com>
Tested-by: Vikash Garodia <quic_vgarodia@quicinc.com> # on sa8775p-ride
Signed-off-by: Bryan O'Donoghue <bod@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
[hverkuil: add __maybe_unused to size_mp2d_lb_fe_top_data]
Subscribe and set mandatory properties to the firmware for HEVC and VP9
decoders.
Acked-by: Vikash Garodia <quic_vgarodia@quicinc.com>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-HDK
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-QRD
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-HDK
Signed-off-by: Dikshita Agarwal <quic_dikshita@quicinc.com>
Tested-by: Vikash Garodia <quic_vgarodia@quicinc.com> # on sa8775p-ride
Signed-off-by: Bryan O'Donoghue <bod@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Add platform capabilities for HEVC and VP9 codecs in decoder driver
with related hooks.
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Acked-by: Vikash Garodia <quic_vgarodia@quicinc.com>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-HDK
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-QRD
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-HDK
Signed-off-by: Dikshita Agarwal <quic_dikshita@quicinc.com>
Tested-by: Vikash Garodia <quic_vgarodia@quicinc.com> # on sa8775p-ride
Signed-off-by: Bryan O'Donoghue <bod@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Extend the decoder driver's supported formats to include HEVC (H.265)
and VP9. This change updates the format enumeration (VIDIOC_ENUM_FMT)
and allows setting these formats via VIDIOC_S_FMT.
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Acked-by: Vikash Garodia <quic_vgarodia@quicinc.com>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-HDK
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-QRD
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-HDK
Signed-off-by: Dikshita Agarwal <quic_dikshita@quicinc.com>
Tested-by: Vikash Garodia <quic_vgarodia@quicinc.com> # on sa8775p-ride
Signed-off-by: Bryan O'Donoghue <bod@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Add a comment to explain usage of MBPS and define a macro for 8K
resolution for better readability
Acked-by: Vikash Garodia <quic_vgarodia@quicinc.com>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-HDK
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-QRD
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-HDK
Signed-off-by: Dikshita Agarwal <quic_dikshita@quicinc.com>
Tested-by: Vikash Garodia <quic_vgarodia@quicinc.com> # on sa8775p-ride
Signed-off-by: Bryan O'Donoghue <bod@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Currently, the stream off process checks the count of buffers in
v4l2_m2m_queues using v4l2_m2m_for_each_src_buf_safe and
v4l2_m2m_for_each_dst_buf_safe APIs. If the count is non-zero, it
returns an error. This check is redundant as the V4L2 framework already
handles buffer management internally.
Remove the unnecessary buffer count check in stream off, simplifying the
process and relying on V4L2's internal mechanisms for buffer management.
Acked-by: Vikash Garodia <quic_vgarodia@quicinc.com>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-HDK
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-QRD
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-HDK
Signed-off-by: Dikshita Agarwal <quic_dikshita@quicinc.com>
Tested-by: Vikash Garodia <quic_vgarodia@quicinc.com> # on sa8775p-ride
Signed-off-by: Bryan O'Donoghue <bod@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Improve the handling of the V4L2_BUF_FLAG_LAST flag in the driver:
- Ensure that the last flag is not sent multiple times.
- Attach the last flag to the first capture buffer returned during
flush, triggered by a sequence change, addressing cases where the
firmware does not set the last flag.
Reviewed-by: Vikash Garodia <quic_vgarodia@quicinc.com>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-HDK
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-QRD
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-HDK
Signed-off-by: Dikshita Agarwal <quic_dikshita@quicinc.com>
Tested-by: Vikash Garodia <quic_vgarodia@quicinc.com> # on sa8775p-ride
Signed-off-by: Bryan O'Donoghue <bod@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Firmware sends the picture type as NO_SHOW for frames which are not
supposed to be displayed, add handling for the same in driver to drop
them.
Acked-by: Vikash Garodia <quic_vgarodia@quicinc.com>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-HDK
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-QRD
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-HDK
Signed-off-by: Dikshita Agarwal <quic_dikshita@quicinc.com>
Tested-by: Vikash Garodia <quic_vgarodia@quicinc.com> # on sa8775p-ride
Signed-off-by: Bryan O'Donoghue <bod@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Firmware attach DATACORRUPT/DROP buffer flags for the frames which
needs to be dropped, handle it by setting VB2_BUF_STATE_ERROR for these
buffers before calling buf_done.
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Acked-by: Vikash Garodia <quic_vgarodia@quicinc.com>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-HDK
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-QRD
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-HDK
Signed-off-by: Dikshita Agarwal <quic_dikshita@quicinc.com>
Tested-by: Vikash Garodia <quic_vgarodia@quicinc.com> # on sa8775p-ride
Signed-off-by: Bryan O'Donoghue <bod@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Currently, The flush completion signal is being re-initialized even
though no response is expected during a sequence change.
Simplify the code by removing re-initialization of flush completion
signal as it is redundant.
Cc: stable@vger.kernel.org
Fixes: 84e17adae3 ("media: iris: add support for dynamic resolution change")
Acked-by: Vikash Garodia <quic_vgarodia@quicinc.com>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-HDK
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-QRD
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-HDK
Signed-off-by: Dikshita Agarwal <quic_dikshita@quicinc.com>
Tested-by: Vikash Garodia <quic_vgarodia@quicinc.com> # on sa8775p-ride
Signed-off-by: Bryan O'Donoghue <bod@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Add a condition to skip the flush operation during the first sequence
change event. At this point, the capture queue is not streaming, making
the flush unnecessary.
Cc: stable@vger.kernel.org
Fixes: 84e17adae3 ("media: iris: add support for dynamic resolution change")
Acked-by: Vikash Garodia <quic_vgarodia@quicinc.com>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-HDK
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-QRD
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-HDK
Signed-off-by: Dikshita Agarwal <quic_dikshita@quicinc.com>
Tested-by: Vikash Garodia <quic_vgarodia@quicinc.com> # on sa8775p-ride
Signed-off-by: Bryan O'Donoghue <bod@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Firmware sends capture buffers with 0 filled length which are not to be
displayed and should be dropped by client.
To achieve the same, add V4L2_BUF_FLAG_ERROR to such buffers by making
sure:
- These 0 length buffers are not returned as result of flush.
- Its not a buffer with LAST flag enabled which will also have 0 filled
length.
Cc: stable@vger.kernel.org
Fixes: d09100763b ("media: iris: add support for drain sequence")
Acked-by: Vikash Garodia <quic_vgarodia@quicinc.com>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-HDK
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-QRD
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-HDK
Signed-off-by: Dikshita Agarwal <quic_dikshita@quicinc.com>
Tested-by: Vikash Garodia <quic_vgarodia@quicinc.com> # on sa8775p-ride
Signed-off-by: Bryan O'Donoghue <bod@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
When the resolution changes, the driver internally updates the width and
height, but the client continue to queue buffers with the older
resolution until the last flag is received. This results in a mismatch
when the buffers are prepared, causing failure due to outdated size.
Introduce a check to prevent size validation during buffer preparation
if a resolution reconfiguration is in progress, to handle this.
Cc: stable@vger.kernel.org
Fixes: 17f2a485ca ("media: iris: implement vb2 ops for buf_queue and firmware response")
Reviewed-by: Vikash Garodia <quic_vgarodia@quicinc.com>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-HDK
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-QRD
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-HDK
Signed-off-by: Dikshita Agarwal <quic_dikshita@quicinc.com>
Tested-by: Vikash Garodia <quic_vgarodia@quicinc.com> # on sa8775p-ride
Signed-off-by: Bryan O'Donoghue <bod@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Currently, two types of flush commands are queued to the firmware,
the first flush queued as part of sequence change, does not wait for a
response, while the second flush queued as part of stop, expects a
completion response before proceeding further.
Due to timing issue, the flush response corresponding to the first
command could arrive after the second flush is issued. This casuses the
driver to incorrectly assume that the second flush has completed,
leading to the premature signaling of flush_completion.
To address this, introduce a counter to track the number of pending
flush responses and signal flush completion only when all expected
responses are received.
Cc: stable@vger.kernel.org
Fixes: 11712ce70f ("media: iris: implement vb2 streaming ops")
Reviewed-by: Vikash Garodia <quic_vgarodia@quicinc.com>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-HDK
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-QRD
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-HDK
Signed-off-by: Dikshita Agarwal <quic_dikshita@quicinc.com>
Tested-by: Vikash Garodia <quic_vgarodia@quicinc.com> # on sa8775p-ride
Signed-off-by: Bryan O'Donoghue <bod@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Correct a typo from "dpeth" to "depth".
Cc: stable@vger.kernel.org
Fixes: 3a19d7b9e0 ("media: iris: implement set properties to firmware during streamon")
Acked-by: Vikash Garodia <quic_vgarodia@quicinc.com>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-HDK
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-QRD
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-HDK
Signed-off-by: Dikshita Agarwal <quic_dikshita@quicinc.com>
Tested-by: Vikash Garodia <quic_vgarodia@quicinc.com> # on sa8775p-ride
Signed-off-by: Bryan O'Donoghue <bod@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
A warning reported by smatch indicated a possible null pointer
dereference where one of the arguments to API
"iris_hfi_gen2_handle_system_error" could sometimes be null.
To fix this, add a check to validate that the argument passed is not
null before accessing its members.
Cc: stable@vger.kernel.org
Fixes: fb583a2143 ("media: iris: introduce host firmware interface with necessary hooks")
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/linux-media/634cc9b8-f099-4b54-8556-d879fb2b5169@stanley.mountain/
Acked-by: Vikash Garodia <quic_vgarodia@quicinc.com>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-HDK
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-QRD
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-HDK
Signed-off-by: Dikshita Agarwal <quic_dikshita@quicinc.com>
Tested-by: Vikash Garodia <quic_vgarodia@quicinc.com> # on sa8775p-ride
Signed-off-by: Bryan O'Donoghue <bod@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
The function pointers responsible for setting firmware properties were
never initialized in the instance capability structure, causing it to
remain NULL. As a result, the firmware properties were not being set
correctly.
Fix this by properly assigning the function pointers from the core
capability to the instance capability, ensuring that the properties are
correctly applied to the firmware.
Cc: stable@vger.kernel.org
Fixes: 3a19d7b9e0 ("media: iris: implement set properties to firmware during streamon")
Acked-by: Vikash Garodia <quic_vgarodia@quicinc.com>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-HDK
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-QRD
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-HDK
Signed-off-by: Dikshita Agarwal <quic_dikshita@quicinc.com>
Tested-by: Vikash Garodia <quic_vgarodia@quicinc.com> # on sa8775p-ride
Signed-off-by: Bryan O'Donoghue <bod@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
HFI_PROPERTY_CONFIG_VDEC_POST_LOOP_DEBLOCKER is deprecated and no longer
supported on current firmware, remove setting the same to firmware.
Cc: stable@vger.kernel.org
Fixes: 79865252ac ("media: iris: enable video driver probe of SM8250 SoC")
Acked-by: Vikash Garodia <quic_vgarodia@quicinc.com>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-HDK
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-QRD
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-HDK
Signed-off-by: Dikshita Agarwal <quic_dikshita@quicinc.com>
Tested-by: Vikash Garodia <quic_vgarodia@quicinc.com> # on sa8775p-ride
Signed-off-by: Bryan O'Donoghue <bod@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Remove the check for non-zero number of v4l2 controls as some SOCs might
not expose any capability which requires v4l2 control.
Cc: stable@vger.kernel.org
Fixes: 33be1dde17 ("media: iris: implement iris v4l2_ctrl_ops")
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-HDK
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-QRD
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-HDK
Signed-off-by: Dikshita Agarwal <quic_dikshita@quicinc.com>
Tested-by: Vikash Garodia <quic_vgarodia@quicinc.com> # on sa8775p-ride
Signed-off-by: Bryan O'Donoghue <bod@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
