As disable_slot() takes a struct zpci_dev from the Configured to the
Standby state. In Standby there is still a hotplug slot so this is not
usually a case of sysfs self deletion. This is important because self
deletion gets very hairy in terms of locking (see for example
recover_store() in arch/s390/pci/pci_sysfs.c).
Because the pci_dev_put() is not within the critical section of the
zdev->state_lock however, disable_slot() can turn into a case of self
deletion if zPCI device event handling slips between the mutex_unlock()
and the pci_dev_put(). If the latter is the last put and
zpci_release_device() is called this then tries to remove the hotplug
slot via zpci_exit_slot() which will try to remove the hotplug slot
directory the disable_slot() is part of i.e. self deletion.
Prevent this by widening the zdev->state_lock critical section to
include the pci_dev_put() which is then guaranteed to happen with the
struct zpci_dev still in Standby state ensuring it will not lead to
a zpci_release_device() call as at least the zPCI event handling code
still holds a reference.
Cc: stable@vger.kernel.org
Fixes: a46044a92a ("s390/pci: fix zpci_zdev_put() on reserve")
Reviewed-by: Gerd Bayer <gbayer@linux.ibm.com>
Tested-by: Gerd Bayer <gbayer@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Remove zpci_bus_remove_device() and zpci_disable_device() calls from
zpci_release_device(). These calls were done when the device
transitioned into the ZPCI_FN_STATE_STANDBY state which is guaranteed to
happen before it enters the ZPCI_FN_STATE_RESERVED state. When
zpci_release_device() is called the device is known to be in the
ZPCI_FN_STATE_RESERVED state which is also checked by a WARN_ON().
Cc: stable@vger.kernel.org
Fixes: a46044a92a ("s390/pci: fix zpci_zdev_put() on reserve")
Reviewed-by: Gerd Bayer <gbayer@linux.ibm.com>
Reviewed-by: Julian Ruess <julianr@linux.ibm.com>
Tested-by: Gerd Bayer <gbayer@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Replace spin_lock_irqsave/spin_unlock_irqrestore with
spin_lock_irq/spin_unlock_irq at places where it is known that interrupts
are enabled.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Benjamin Marzinski <bmarzins@redhat.com>
Note - last minute rebase was to drop a typo patch that I'd accidentally
picked up (in the microblaze arch Kconfig)
Take 2 is due to that rebase messing up some fixes tags that were
referring to patches after that point.
There is a known merge conflict due to changes in neighbouring lines.
Stephen's resolution in linux-next is:
https://lore.kernel.org/linux-next/20250506155728.65605bae@canb.auug.org.au/
Added 3 named IIO reviewers to MAINTAINERS. This is a reflection of those
who have been doing much of this work for some time. Lars-Peter is
removed from the entry having moved on to other topics. Thanks
Nuno, David and Andy for stepping up and Lars-Peter for all your
hard work in the past!
Includes the usual mix of new device support, features and general
cleanup.
This time we also have some tree wide changes.
- Rip out the iio_device_claim_direct_scoped() as it proved hard to work
with. This series includes quite a few related cleanups such as use
of guard or factoring code out to allow direct returns.
- Switch from iio_device_claim/release_direct_mode() to new
iio_device_claim/release_direct() which is structured so that sparse
can warn on failed releases. There were a few false positives but
those were mostly in code that benefited from being cleaned up as part
of this process.
- Introduce iio_push_to_buffers_with_ts() to replace the _timestamp()
version over time. This version takes the size of the supplied buffer
which the core checks is at least as big as expected by calculation
from channel descriptions of those channels enabled. Use this in
an initial set of drivers.
- Add macros for IIO_DECLARE_BUFFER_WITH_TS() and
IIO_DECLARE_DMA_BUFFER_WITH_TS() to avoid lots of fiddly code to ensure
correctly aligned buffers for timestamps being added onto the end of
channel data.
New device support
------------------
adi,ad3530r
- New driver for AD3530, AD3530R, AD3531 and AD3531R DACs with
programmable gain controls. R variants have internal references.
adi,ad7476
- Add support (dt compatible only) for the Rohm BU79100G ADC which is
fully compatible with the ti,ads7866.
adi,ad7606
- Support ad7606c-16 and ad7606c-18 devices. Includes switch to dynamic
channel information allocation.
adi,ad7380
- Add support for the AD7389-4
dfrobot,sen0322
- New driver for this oxygen sensor.
mediatek,mt2701-auxadc
- Add binding for MT6893 which is fully compatible with already supported
MT8173.
meson-saradc
- Support the GXLX SoCs. Mostly this is a workaround for some unrelated
clock control bits found in the ADC register map.
nuvoton,nct7201
- New driver for NCT7201 and NCT7202 I2C ADCs.
rohm,bd79124
- New driver for this 12-bit, 8-channel SAR ADC.
- Switch to new set_rv etc gpio callbacks that were added in 6.15.
rohm,bd79703
- Add support for BD79700, BD79701 and BD79702 DACs that have subsets of
functionality of the already supported bd79703. Included making this
driver suitable for support device variants.
st,stm32-lptimer
- Add support for stm32pm25 to this trigger.
Features
--------
Beyond IIO
- Property iterator for named children.
core
- Enable writes for 64 bit integers used for standard IIO ABI elements.
Previously these could be read only.
- Helper library that should avoid code duplication for simpler ADC
bindings that have a child node per channel.
- Enforce that IIO_DMA_MINALIGN is always at least 8 (almost always true
and simplifies code on all significant architectures)
core/backend
- Add support to control source of data - useful when the HDL includes
things like generated ramps for testing purposes. Enable this for
adi-axi-dac
adi,ad3552-hs
- Add debugfs related callbacks to allow debug access to register contents.
adi,ad4000
- Support SPI offload with appropriate FPGA firmware along with improving
documentation.
adi,ad7293
- Add support for external reference voltage.
adi,ad7606
- Support SPI offload.
adi,ad7768-1
- Support reset GPIO.
adi,admv8818
- Support filter frequencies beyond 2^32.
adi,adxl345
- Add single and double tap events.
hid-sensor-prox
- Support 16-bit report sizes as seen on some Intel platforms.
invensense,icm42600
- Enable use of named interrupts to avoid problems with some wiring choices.
Get the interrupt by name, but fallback to previous assumption on the first
being INT1 if no names are supplied.
microchip,mcp3911
- Add reset gpio support.
rohm,bh7150
- Add reset gpio support.
st,stm32
- Add support to control oversampling.
ti,adc128s052
- Add support for ROHM BD79104 which is early compatible with the TI
parts already supported by this driver. Includes some general driver
cleanup and a separate dt binding.
- Simplify reference voltage handling by assuming it is fixed after enabling
the supply.
winsen,mhz19b
- New driver for this C02 sensor.
Cleanup and minor fixes
-----------------------
dt-bindings
- Correct indentation and style for DTS examples.
- Use unevalutateProperties for SPI devices instead of additionalProperties
to allow generic SPI properties from spi-peripheral-props.yaml
ABI Docs
- Add missing docs for sampling_frequency when it applies only to events.
Treewide
- Various minor tweaks, comment fixes and similar.
- Sort TI ADCs in Kconfig that had gotten out of order.
- Switch various drives that provide GPIO chip functionality to the new
callbacks with return values.
- Standardize on { } formatting for all array sentinels.
- Make use of aligned_s64 in a few places to replace either wrong types
or manually defined equivalents.
- Drop places where spi bits_per_word is set to 8 because that is the
default anyway.
adi,ad_sigma_delta library
- Avoid a potential use of uninitialized data if reg_size has a value
that is not supported (no drivers hit this but it is reasonable hardening)
adi,ad4030
- Add error checking for scan types and no longer store it in state.
- Rework code to reduce duplication.
- Move setting the mode from buffer preenable() to update_scan_mode(),
better matching expected semantics of the two different callbacks.
- Improve data marshalling comments.
adi,ad4695
- Use u16 for buffer elements as oversampling is not yet supported except
with SPI offload (which doesn't use this path).
adi,ad5592r
- Clean up destruction of mutexes.
- Use lock guards to simplify code (later patch fixes a missed unlock)
adi,ad5933
- Correct some incorrect settling times.
adi,ad7091
- Deduplicate handling of writable vs volatile registers as they are the
inverse of each other for this device.
adi,ad7124
- Fix 3db Filter frequency.
- Remove ability to directly write the filter frequency (which was broken)
- Register naming improvements.
adi,ad7606
- Add a missing return value check.
- Fill in max sampling rates for all chips.
- Use devm_mutex_init()
- Fix up some kernel-doc formatting issues.
- Remove some camel case that snuck in.
- Drop setting address field in channels as easily established from other
fields.
- Drop unnecessary parameter to ad76060_scale_setup_cb_t.
adi,ad7768-1
- Convert to regmap.
- Factor out buffer allocation.
- Tidy up headers.
adi,ad7944
- Stop setting bits_per_word in SPI xfers with no data.
adi,ad9832
- Add of_device_id table rather than just relying on fallbacks.
- Use FIELD_PREP() to set values of fields.
adi,admv1013
- Cleanup a pointless ternary.
adi,admv8818
- Fix up LPF Band 5 frequency which was slightly wrong.
- Fix an integer overflow.
- Fix range calculation
adi,adt7316
- Replace irqd_get_trigger_type(irq_get_irq_data()) with simpler
irq_get_trigger_type()
adi,adxl345
- Use regmap cache instead of various state variables that were there to
reduce bus accesses.
- Make regmap return value checking consistent across all call sites.
adi,axi-dac
- Add a check on number of channels (0 to 15 valid)
allwinner,sun20i
- Use new adc-helpers to replace local parsing code for channel nodes.
bosch,bmp290
- Move to local variables for sensor data marshalling removing the need
for a messy definition that has to work for all supported parts.
Follow up fix adds a missing initialization.
dynaimage,al3010 and dynaimage,al3320a
- Various minor cleanup to bring these drivers inline with reviewed feedback
given on a new driver.
- Fix an error path in which power down is not called when it should be.
- Switch to regmap.
google,cros_ec
- Fix up a flexible array in middle of structure warning.
- Flush fifo when changing the timeout to avoid potential long wait
for samples.
hid-sensor-rotation
- Remove an __aligned(16) marking that doesn't seem to be justified.
kionix,kxcjk-1013
- Deduplicate code for setting up interrupts.
microchip,mcp3911
- Fix handling of conversion results register which differs across supported
devices.
idt,zopt2201
- Avoid duplicating register lists as all volatile registers are the
inverse of writeable registers on this device.
renesas,rzg2l
- Use new adc-helpers to replace local parsing code for channel nodes.
ti,ads1298
- Fix a missing Kconfig dependency.
-----BEGIN PGP SIGNATURE-----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=vLKV
-----END PGP SIGNATURE-----
Merge tag 'iio-for-6.16a-take2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/jic23/iio into char-misc-next
Jonathan writes:
IIO: New device support, features and cleanup for 6.16 - take 2
Note - last minute rebase was to drop a typo patch that I'd accidentally
picked up (in the microblaze arch Kconfig)
Take 2 is due to that rebase messing up some fixes tags that were
referring to patches after that point.
There is a known merge conflict due to changes in neighbouring lines.
Stephen's resolution in linux-next is:
https://lore.kernel.org/linux-next/20250506155728.65605bae@canb.auug.org.au/
Added 3 named IIO reviewers to MAINTAINERS. This is a reflection of those
who have been doing much of this work for some time. Lars-Peter is
removed from the entry having moved on to other topics. Thanks
Nuno, David and Andy for stepping up and Lars-Peter for all your
hard work in the past!
Includes the usual mix of new device support, features and general
cleanup.
This time we also have some tree wide changes.
- Rip out the iio_device_claim_direct_scoped() as it proved hard to work
with. This series includes quite a few related cleanups such as use
of guard or factoring code out to allow direct returns.
- Switch from iio_device_claim/release_direct_mode() to new
iio_device_claim/release_direct() which is structured so that sparse
can warn on failed releases. There were a few false positives but
those were mostly in code that benefited from being cleaned up as part
of this process.
- Introduce iio_push_to_buffers_with_ts() to replace the _timestamp()
version over time. This version takes the size of the supplied buffer
which the core checks is at least as big as expected by calculation
from channel descriptions of those channels enabled. Use this in
an initial set of drivers.
- Add macros for IIO_DECLARE_BUFFER_WITH_TS() and
IIO_DECLARE_DMA_BUFFER_WITH_TS() to avoid lots of fiddly code to ensure
correctly aligned buffers for timestamps being added onto the end of
channel data.
New device support
------------------
adi,ad3530r
- New driver for AD3530, AD3530R, AD3531 and AD3531R DACs with
programmable gain controls. R variants have internal references.
adi,ad7476
- Add support (dt compatible only) for the Rohm BU79100G ADC which is
fully compatible with the ti,ads7866.
adi,ad7606
- Support ad7606c-16 and ad7606c-18 devices. Includes switch to dynamic
channel information allocation.
adi,ad7380
- Add support for the AD7389-4
dfrobot,sen0322
- New driver for this oxygen sensor.
mediatek,mt2701-auxadc
- Add binding for MT6893 which is fully compatible with already supported
MT8173.
meson-saradc
- Support the GXLX SoCs. Mostly this is a workaround for some unrelated
clock control bits found in the ADC register map.
nuvoton,nct7201
- New driver for NCT7201 and NCT7202 I2C ADCs.
rohm,bd79124
- New driver for this 12-bit, 8-channel SAR ADC.
- Switch to new set_rv etc gpio callbacks that were added in 6.15.
rohm,bd79703
- Add support for BD79700, BD79701 and BD79702 DACs that have subsets of
functionality of the already supported bd79703. Included making this
driver suitable for support device variants.
st,stm32-lptimer
- Add support for stm32pm25 to this trigger.
Features
--------
Beyond IIO
- Property iterator for named children.
core
- Enable writes for 64 bit integers used for standard IIO ABI elements.
Previously these could be read only.
- Helper library that should avoid code duplication for simpler ADC
bindings that have a child node per channel.
- Enforce that IIO_DMA_MINALIGN is always at least 8 (almost always true
and simplifies code on all significant architectures)
core/backend
- Add support to control source of data - useful when the HDL includes
things like generated ramps for testing purposes. Enable this for
adi-axi-dac
adi,ad3552-hs
- Add debugfs related callbacks to allow debug access to register contents.
adi,ad4000
- Support SPI offload with appropriate FPGA firmware along with improving
documentation.
adi,ad7293
- Add support for external reference voltage.
adi,ad7606
- Support SPI offload.
adi,ad7768-1
- Support reset GPIO.
adi,admv8818
- Support filter frequencies beyond 2^32.
adi,adxl345
- Add single and double tap events.
hid-sensor-prox
- Support 16-bit report sizes as seen on some Intel platforms.
invensense,icm42600
- Enable use of named interrupts to avoid problems with some wiring choices.
Get the interrupt by name, but fallback to previous assumption on the first
being INT1 if no names are supplied.
microchip,mcp3911
- Add reset gpio support.
rohm,bh7150
- Add reset gpio support.
st,stm32
- Add support to control oversampling.
ti,adc128s052
- Add support for ROHM BD79104 which is early compatible with the TI
parts already supported by this driver. Includes some general driver
cleanup and a separate dt binding.
- Simplify reference voltage handling by assuming it is fixed after enabling
the supply.
winsen,mhz19b
- New driver for this C02 sensor.
Cleanup and minor fixes
-----------------------
dt-bindings
- Correct indentation and style for DTS examples.
- Use unevalutateProperties for SPI devices instead of additionalProperties
to allow generic SPI properties from spi-peripheral-props.yaml
ABI Docs
- Add missing docs for sampling_frequency when it applies only to events.
Treewide
- Various minor tweaks, comment fixes and similar.
- Sort TI ADCs in Kconfig that had gotten out of order.
- Switch various drives that provide GPIO chip functionality to the new
callbacks with return values.
- Standardize on { } formatting for all array sentinels.
- Make use of aligned_s64 in a few places to replace either wrong types
or manually defined equivalents.
- Drop places where spi bits_per_word is set to 8 because that is the
default anyway.
adi,ad_sigma_delta library
- Avoid a potential use of uninitialized data if reg_size has a value
that is not supported (no drivers hit this but it is reasonable hardening)
adi,ad4030
- Add error checking for scan types and no longer store it in state.
- Rework code to reduce duplication.
- Move setting the mode from buffer preenable() to update_scan_mode(),
better matching expected semantics of the two different callbacks.
- Improve data marshalling comments.
adi,ad4695
- Use u16 for buffer elements as oversampling is not yet supported except
with SPI offload (which doesn't use this path).
adi,ad5592r
- Clean up destruction of mutexes.
- Use lock guards to simplify code (later patch fixes a missed unlock)
adi,ad5933
- Correct some incorrect settling times.
adi,ad7091
- Deduplicate handling of writable vs volatile registers as they are the
inverse of each other for this device.
adi,ad7124
- Fix 3db Filter frequency.
- Remove ability to directly write the filter frequency (which was broken)
- Register naming improvements.
adi,ad7606
- Add a missing return value check.
- Fill in max sampling rates for all chips.
- Use devm_mutex_init()
- Fix up some kernel-doc formatting issues.
- Remove some camel case that snuck in.
- Drop setting address field in channels as easily established from other
fields.
- Drop unnecessary parameter to ad76060_scale_setup_cb_t.
adi,ad7768-1
- Convert to regmap.
- Factor out buffer allocation.
- Tidy up headers.
adi,ad7944
- Stop setting bits_per_word in SPI xfers with no data.
adi,ad9832
- Add of_device_id table rather than just relying on fallbacks.
- Use FIELD_PREP() to set values of fields.
adi,admv1013
- Cleanup a pointless ternary.
adi,admv8818
- Fix up LPF Band 5 frequency which was slightly wrong.
- Fix an integer overflow.
- Fix range calculation
adi,adt7316
- Replace irqd_get_trigger_type(irq_get_irq_data()) with simpler
irq_get_trigger_type()
adi,adxl345
- Use regmap cache instead of various state variables that were there to
reduce bus accesses.
- Make regmap return value checking consistent across all call sites.
adi,axi-dac
- Add a check on number of channels (0 to 15 valid)
allwinner,sun20i
- Use new adc-helpers to replace local parsing code for channel nodes.
bosch,bmp290
- Move to local variables for sensor data marshalling removing the need
for a messy definition that has to work for all supported parts.
Follow up fix adds a missing initialization.
dynaimage,al3010 and dynaimage,al3320a
- Various minor cleanup to bring these drivers inline with reviewed feedback
given on a new driver.
- Fix an error path in which power down is not called when it should be.
- Switch to regmap.
google,cros_ec
- Fix up a flexible array in middle of structure warning.
- Flush fifo when changing the timeout to avoid potential long wait
for samples.
hid-sensor-rotation
- Remove an __aligned(16) marking that doesn't seem to be justified.
kionix,kxcjk-1013
- Deduplicate code for setting up interrupts.
microchip,mcp3911
- Fix handling of conversion results register which differs across supported
devices.
idt,zopt2201
- Avoid duplicating register lists as all volatile registers are the
inverse of writeable registers on this device.
renesas,rzg2l
- Use new adc-helpers to replace local parsing code for channel nodes.
ti,ads1298
- Fix a missing Kconfig dependency.
* tag 'iio-for-6.16a-take2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (260 commits)
dt-bindings: iio: adc: Add ROHM BD79100G
iio: adc: add support for Nuvoton NCT7201
dt-bindings: iio: adc: add NCT7201 ADCs
iio: chemical: Add driver for SEN0322
dt-bindings: trivial-devices: Document SEN0322
iio: adc: ad7768-1: reorganize driver headers
iio: bmp280: zero-init buffer
iio: ssp_sensors: optimalize -> optimize
HID: sensor-hub: Fix typo and improve documentation
iio: admv1013: replace redundant ternary operator with just len
iio: chemical: mhz19b: Fix error code in probe()
iio: adc: at91-sama5d2: use IIO_DECLARE_BUFFER_WITH_TS
iio: accel: sca3300: use IIO_DECLARE_BUFFER_WITH_TS
iio: adc: ad7380: use IIO_DECLARE_DMA_BUFFER_WITH_TS
iio: adc: ad4695: rename AD4695_MAX_VIN_CHANNELS
iio: adc: ad4695: use IIO_DECLARE_DMA_BUFFER_WITH_TS
iio: introduce IIO_DECLARE_BUFFER_WITH_TS macros
iio: make IIO_DMA_MINALIGN minimum of 8 bytes
iio: pressure: zpa2326_spi: remove bits_per_word = 8
iio: pressure: ms5611_spi: remove bits_per_word = 8
...
`bindgen` currently generates the wrong type for an `enum` when there
is a forward reference to it. For instance:
enum E;
enum E { A };
generates:
pub const E_A: E = 0;
pub type E = i32;
instead of the expected:
pub const E_A: E = 0;
pub type E = ffi::c_uint;
The issue was reported to upstream `bindgen` [1].
Now, both GCC and Clang support silently these forward references to
`enum` types, unless `-Wpedantic` is passed, and it turns out that some
headers in the kernel depend on them.
Thus, depending on how the headers are included, which in turn may depend
on the kernel configuration or the architecture, we may get a different
type on the Rust side for a given C `enum`.
That can be quite confusing, to say the least, especially since
developers may only notice issues when building for other architectures
like in [2]. In particular, they may end up forcing a cast and adding
an `#[allow(clippy::unnecessary_cast)]` like it was done in commit
94e05a66ea ("rust: hrtimer: allow timer restart from timer handler"),
which isn't great.
Instead, let's have a section at the top of our `bindings_helper.h` that
`#include`s the headers with the affected types -- hopefully there are
not many cases and there is a single ordering that covers all cases.
This allows us to remove the cast and the `#[allow]`, thus keeping the
correct code in the source files. When the issue gets resolved in upstream
`bindgen` (and we update our minimum `bindgen` version), we can easily
remove this section at the top.
Link: https://github.com/rust-lang/rust-bindgen/issues/3179 [1]
Link: https://lore.kernel.org/rust-for-linux/87tt7md1s6.fsf@kernel.org/ [2]
Acked-by: Andreas Hindborg <a.hindborg@kernel.org>
Link: https://lore.kernel.org/r/20250325184309.97170-1-ojeda@kernel.org
[ Added extra paragraph on the comment to clarify that the workaround may
not be possible in some cases. - Miguel ]
Signed-off-by: Miguel Ojeda <ojeda@kernel.org>
Merge series from "Sheetal ." <sheetal@nvidia.com>:
The patch series includes the necessary changes to enable
support for the Tegra264 platforms in AHUB drivers.
Multi-PTP source support within a network topology has been merged,
but the hardware timestamp source is not yet exposed to users.
Currently, users only see the PTP index, which does not indicate
whether the timestamp comes from a PHY or a MAC.
Add support for reporting the hwtstamp source using a
hwtstamp-source field, alongside hwtstamp-phyindex, to describe
the origin of the hardware timestamp.
Remove HWTSTAMP_SOURCE_UNSPEC enum value as it is not used at all.
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Link: https://patch.msgid.link/20250519-feature_ptp_source-v4-1-5d10e19a0265@bootlin.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Convert cdn-dp-rockchip.txt to yaml.
Add new "port@1" property which represents the CDN DP output to keep
the same style as the other display interfaces.
This patch also changes the constraints for "phys" and "extcon". For
the original binding, only one phy and the corresponding extcon can
be specified. In the new binding, one or two phys can be specified.
Since the RK3399 has two DP-USB PHYs, specifying one allows output
via the corresponding PHY, while specifying two lets the driver
choose one PHY for output. This rule also applies to extcon, which
provides the cable state for the corresponding PHY.
Signed-off-by: Chaoyi Chen <chaoyi.chen@rock-chips.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250520024718.142-3-kernel@airkyi.com
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Some GPIO chips allow to rise an IRQ on GPIO level changes but do not
provide an IRQ status for each separate line: only the current gpio
level can be retrieved.
Add support for these chips, emulating IRQ status by comparing GPIO
levels with the levels during the previous interrupt.
Signed-off-by: Mathieu Dubois-Briand <mathieu.dubois-briand@bootlin.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20250522-mdb-max7360-support-v9-5-74fc03517e41@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The cirrus_dir pointer should be const data but was missing the second
const needed to achieve this.
I haven't marked this as a 'Fixes' because it isn't causing any bugs,
it's only a code improvement.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://patch.msgid.link/20250522103816.543919-1-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
- Various fixes and cleanups from Ioana on fsl-mc bus driver
- Other misc fixes on fsl-mc bus driver
- A build fix on DPAA2 driver
- Some preparation work from Kees on qbman driver
- Some cleanup on FSL qe interrupt driver init
-----BEGIN PGP SIGNATURE-----
iJIEABYKADoWIQQQ/+b4s5DeF6zCYyNoqS/rAbjdeAUCaChUGBwcY2hyaXN0b3Bo
ZS5sZXJveUBjc2dyb3VwLmV1AAoJEGipL+sBuN14P8cBAIWy+9x5gfkg7ndHDYQk
4DKYVuAC2ox4HRgQr/lAAyRzAP9zhtL/r8xjSeomn0Uk/vGbzdRNqQo5/l3vbp5i
Tj8KDw==
=lpqg
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=StL6
-----END PGP SIGNATURE-----
Merge tag 'soc_fsl-6.16-1' of https://github.com/chleroy/linux into soc/drivers
FSL SOC Changes for 6.16:
- Various fixes and cleanups from Ioana on fsl-mc bus driver
- Other misc fixes on fsl-mc bus driver
- A build fix on DPAA2 driver
- Some preparation work from Kees on qbman driver
- Some cleanup on FSL qe interrupt driver init
* tag 'soc_fsl-6.16-1' of https://github.com/chleroy/linux:
soc: fsl: qe: Consolidate chained IRQ handler install/remove
bus: fsl-mc: Use strscpy() instead of strscpy_pad()
soc: fsl: qbman: Remove const from portal->cgrs allocation type
bus: fsl_mc: Fix driver_managed_dma check
bus: fsl-mc: increase MC_CMD_COMPLETION_TIMEOUT_MS value
bus: fsl-mc: drop useless cleanup
bus: fsl-mc: add the dprc_get_mem() command to the whitelist
bus: fsl-mc: fix GET/SET_TAILDROP command ids
bus: fsl-mc: do not add a device-link for the UAPI used DPMCP device
bus: fsl-mc: fix double-free on mc_dev
soc: fsl: Do not enable DPAA2_CONSOLE by default during compile testing
Link: https://lore.kernel.org/r/9e5b3e8e-3280-4ff9-915b-9a8b934bac22@csgroup.eu
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
ath12k:
Add monitor mode support for WCN7850.
Enhance regulatory support including 6 GHz power modes.
In addition, perform the usual set of bug fixes and cleanups across
all supported drivers.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQQ/mtSHzPUi16IfDEksFbugiYzLewUCaC5IEwAKCRAsFbugiYzL
ezMUAQCAH3sy0hJSraoLb+6+VMI/ClBquJVIgOBwVvlXJd4lIgEAwY+uYgSNWkYU
KQ2Zxa8+whDx6oqFJF5qYJ+scMh9VA0=
=b7Wk
-----END PGP SIGNATURE-----
Merge tag 'ath-next-20250521' of git://git.kernel.org/pub/scm/linux/kernel/git/ath/ath
Jeff Johnson says:
==================
ath.git patches for v6.16
ath12k:
Add monitor mode support for WCN7850.
Enhance regulatory support including 6 GHz power modes.
In addition, perform the usual set of bug fixes and cleanups across
all supported drivers.
==================
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
please pull the following for 6.16:
- Krzysztof updates the BCM2711/BCM283X entry to also match on the
bcm2712 pattern to cover the Raspberry Pi 5 files
-----BEGIN PGP SIGNATURE-----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=W5h3
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=UvjF
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-6.16/maintainers' of https://github.com/Broadcom/stblinux into soc/arm
This pull request contains MAINTAINERS file update for Broadcom SoCs,
please pull the following for 6.16:
- Krzysztof updates the BCM2711/BCM283X entry to also match on the
bcm2712 pattern to cover the Raspberry Pi 5 files
* tag 'arm-soc/for-6.16/maintainers' of https://github.com/Broadcom/stblinux:
ARM: broadcom: MAINTAINERS: Cover bcm2712 files
Link: https://lore.kernel.org/r/20250513140808.2047729-1-florian.fainelli@broadcom.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
When a list head is a const pointer, the list entry for that head also
must remain a const pointer, otherwise we are just "throwing it away"
for no good reason. Fix this up by properly marking these structures as
const.
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://patch.msgid.link/2025052213-semifinal-sublevel-d631@gregkh
Signed-off-by: Mark Brown <broonie@kernel.org>
While the struct spi_device * passed into spi_to_spi_gpio() is a const
one, the struct spi_bitbang * that is retrieved from the controller
field in the spi_device is NOT a const pointer, as it is coming from the
spi_controller_get_devdata() call, and then passed to container_of()
which would strip off the const attribute for no good reason (i.e. if a
const pointer is passed to container_of() it still is const coming out).
Fix this all up by properly declaring the struct spi_bitbang * as not
const.
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://patch.msgid.link/2025052225-scallion-ritzy-dbbd@gregkh
Signed-off-by: Mark Brown <broonie@kernel.org>
Some places in the spi core pass in a const pointer to a device and the
default container_of() casts that away, which is not a good idea.
Preserve the proper const attribute by using container_of_const() for
to_spi_device() instead, which is what it was designed for.
Note, this removes the NULL check for a device pointer in the call, but
no one was ever checking for that return value, and a device pointer
should never be NULL overall anyway, so this should be a safe change.
Cc: Mark Brown <broonie@kernel.org>
Fixes: d69d804845 ("driver core: have match() callback in struct bus_type take a const *")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://patch.msgid.link/2025052230-fidgeting-stooge-66f5@gregkh
Signed-off-by: Mark Brown <broonie@kernel.org>
The argument has been unused since the function was added, so remove it.
Signed-off-by: Caleb Sander Mateos <csander@purestorage.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20250521160720.1893326-1-csander@purestorage.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This enables some drivers as modules to enable fully booting
some of the supported MediaTek boards;
In particular, this enables the following drivers as module:
- PHYs for PCIe, HDMI, DSI and DisplayPort for all boards
- MediaTek UART DMA Controller, also for all boards
- MDP3 driver for MT8186/88/95 (Chromebooks and Genio variants)
- Auxiliary ADC for the MT6357/58/59 PMICs found on both Genio EVK
and Chromebooks based on designs with MT8183/86/88/92/95 SoCs
- iTE IT5205 Type-C USB Alternate Mode Passive MUX, found
on both Chromebooks and Genio EVKs with MT8188/95
- Richtek RT1715 Type-C PD Controller, found on all Genio boards
- Himax HX8279 DSI panel DriverIC and KD070FHFID015 panel, found
on various revisions of the Genio Evaluation Kit boards.
-----BEGIN PGP SIGNATURE-----
iJ4EABYKAEYWIQQn3Xxr56ypAcSHzXSaNgTPrZeEeAUCaCxpdSgcYW5nZWxvZ2lv
YWNjaGluby5kZWxyZWdub0Bjb2xsYWJvcmEuY29tAAoJEJo2BM+tl4R4+7kA/j5c
urmSN7qrFH6EWcguxQlDBIUvQebQm+4HeGC4bbHHAQCxiNrsAgzCsG4cYe8BN2Lz
uzDsHBEJIn+T/rBHFfAwDg==
=h8po
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=GJ3+
-----END PGP SIGNATURE-----
Merge tag 'mtk-defconfig-for-v6.16' of https://git.kernel.org/pub/scm/linux/kernel/git/mediatek/linux into soc/defconfig
MediaTek ARM64 defconfig updates for v6.16
This enables some drivers as modules to enable fully booting
some of the supported MediaTek boards;
In particular, this enables the following drivers as module:
- PHYs for PCIe, HDMI, DSI and DisplayPort for all boards
- MediaTek UART DMA Controller, also for all boards
- MDP3 driver for MT8186/88/95 (Chromebooks and Genio variants)
- Auxiliary ADC for the MT6357/58/59 PMICs found on both Genio EVK
and Chromebooks based on designs with MT8183/86/88/92/95 SoCs
- iTE IT5205 Type-C USB Alternate Mode Passive MUX, found
on both Chromebooks and Genio EVKs with MT8188/95
- Richtek RT1715 Type-C PD Controller, found on all Genio boards
- Himax HX8279 DSI panel DriverIC and KD070FHFID015 panel, found
on various revisions of the Genio Evaluation Kit boards.
* tag 'mtk-defconfig-for-v6.16' of https://git.kernel.org/pub/scm/linux/kernel/git/mediatek/linux:
arm64: defconfig: Enable configs for MediaTek Genio EVK boards
arm64: defconfig: mediatek: enable PHY drivers
Link: https://lore.kernel.org/r/20250520114356.1194450-2-angelogioacchino.delregno@collabora.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
In the pci_acpi_scan_root() function, when creating a PCI bus fails,
we need to free up the previously allocated memory, which can avoid
invalid memory usage and save resources.
Fixes: 789befdfa3 ("arm64: PCI: Migrate ACPI related functions to pci-acpi.c")
Signed-off-by: Zhe Qiao <qiaozhe@iscas.ac.cn>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://lore.kernel.org/r/20250430060603.381504-1-qiaozhe@iscas.ac.cn
Enable global clock controller and TLMM pinctrl drivers for IPQ5424 to
make this boot.
-----BEGIN PGP SIGNATURE-----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=sw/L
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=HAVp
-----END PGP SIGNATURE-----
Merge tag 'qcom-arm64-defconfig-for-6.16-2' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into soc/defconfig
One more Qualcomm Arm64 defconfig update for v6.16
Enable global clock controller and TLMM pinctrl drivers for IPQ5424 to
make this boot.
* tag 'qcom-arm64-defconfig-for-6.16-2' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
arm64: defconfig: Enable IPQ5424 RDP466 base configs
Link: https://lore.kernel.org/r/20250520025119.40021-1-andersson@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
PM_GENERIC_DOMAINS is enabled because T-Head SoCs need to use it and
spacemit's gpio and clock controller are enabled for more obvious
reasons.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRh246EGq/8RLhDjO14tDGHoIJi0gUCaCcUngAKCRB4tDGHoIJi
0ql4AQDUpYnIHRMVnyc9wrFl80N+ZM/up31SxVantNXs4aY6DAD/Q11CxeJB8UM4
QGsvAKvsNiySmr665PwgyUXj0SED9QQ=
=+zzo
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=Xv8S
-----END PGP SIGNATURE-----
Merge tag 'riscv-config-for-v6.16' of https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux into soc/defconfig
RISC-V config for v6.16
PM_GENERIC_DOMAINS is enabled because T-Head SoCs need to use it and
spacemit's gpio and clock controller are enabled for more obvious
reasons.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
* tag 'riscv-config-for-v6.16' of https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux:
riscv: defconfig: spacemit: enable clock controller driver for SpacemiT K1
riscv: defconfig: spacemit: enable gpio support for K1 SoC
riscv: Enable PM_GENERIC_DOMAINS for T-Head SoCs
Link: https://lore.kernel.org/r/20250516-joystick-mortified-385820b1ad0b@spud
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
One variant of MT7992 has 5 TX paths, so extend the power delta function
to support it. Also, rename nss_delta to path_delta since the value is
based on the number of TX paths rather tha the number of spatial streams.
(path delta [0.5 dBm] = 10 * log(path number) [dBm] * 2)
Co-developed-by: StanleyYP Wang <StanleyYP.Wang@mediatek.com>
Signed-off-by: StanleyYP Wang <StanleyYP.Wang@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Link: https://patch.msgid.link/20250515032952.1653494-9-shayne.chen@mediatek.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Check if available_antennas_tx and available_antennas_rx are already set
during the per-chip initialization phase; otherwise, they could be
overwritten with incorrect values.
Fixes: 69d54ce749 ("wifi: mt76: mt7996: switch to single multi-radio wiphy")
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Link: https://patch.msgid.link/20250515032952.1653494-8-shayne.chen@mediatek.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Some management frames are first processed by the firmware and then
passed to the driver through the MCU event rings. In CONNAC3, event rings
do not support scatter-gather and have a size limitation of 2048 bytes.
If a packet sized between 1728 and 2048 bytes arrives from an event ring,
the ring will hang because the driver attempts to use scatter-gather to
process it.
To fix this, include the size of struct skb_shared_info in the MCU RX
buffer size to prevent scatter-gather from being used for event skb in
mt76_dma_rx_fill_buf().
Fixes: 98686cd216 ("wifi: mt76: mt7996: add driver for MediaTek Wi-Fi 7 (802.11be) devices")
Co-developed-by: Peter Chiu <chui-hao.chiu@mediatek.com>
Signed-off-by: Peter Chiu <chui-hao.chiu@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Link: https://patch.msgid.link/20250515032952.1653494-7-shayne.chen@mediatek.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
According to hardware capability, the maximum beacon size is 2048 bytes
minus the size of TLV headers.
Signed-off-by: Peter Chiu <chui-hao.chiu@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Link: https://patch.msgid.link/20250515032952.1653494-6-shayne.chen@mediatek.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The maximum TX path and NSS may differ on a band. For example, one variant
of the MT7992 has 5 TX paths and 4 NSS on the 5 GHz band. To address this,
add orig_antenna_mask to record the maximum NSS and prevent setting an
invalid NSS in mt7996_set_antenna().
Fixes: 69d54ce749 ("wifi: mt76: mt7996: switch to single multi-radio wiphy")
Signed-off-by: Peter Chiu <chui-hao.chiu@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Link: https://patch.msgid.link/20250515032952.1653494-5-shayne.chen@mediatek.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
IEEE 802.11 fragmentation can only be applied to unicast frames.
Therefore, drop fragments with multicast or broadcast RA. This patch
addresses vulnerabilities such as CVE-2020-26145.
Signed-off-by: Benjamin Lin <benjamin-jw.lin@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Link: https://patch.msgid.link/20250515032952.1653494-4-shayne.chen@mediatek.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Set the max AMPDU length in the EHT MAC CAP. Without this patch, the
peer station cannot obtain the correct capability, which prevents
achieving peak throughput on the 2 GHz band.
Fixes: 1816ad9381 ("wifi: mt76: mt7996: add max mpdu len capability")
Signed-off-by: Peter Chiu <chui-hao.chiu@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Link: https://patch.msgid.link/20250515032952.1653494-3-shayne.chen@mediatek.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fix the beamformee SS field for the mt7996, mt7992 and mt7990 chipsets.
For the mt7992, this value shall be set to 0x4, while the others shall
be set to 0x3.
Fixes: 5b20557593 ("wifi: mt76: connac: adjust phy capabilities based on band constraints")
Signed-off-by: Howard Hsu <howard-yh.hsu@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Link: https://patch.msgid.link/20250515032952.1653494-2-shayne.chen@mediatek.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The firmware only supports full bandwidth UL MU-MIMO, so remove the
partial bandwidth capability from HE PHY CAP.
Signed-off-by: Howard Hsu <howard-yh.hsu@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Link: https://patch.msgid.link/20250515032952.1653494-1-shayne.chen@mediatek.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The test mode interface allows controlled execution of chip-level
operations such as continuous transmission, reception tests, and
register access, which are essential during bring-up, diagnostics,
and factory testing.
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Michael Lo <michael.lo@mediatek.com>
Link: https://patch.msgid.link/20250505233618.1951021-2-sean.wang@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add MCU command and its handling needed for testmode support on
MT7925. This enables low-level chip testing features such as
continuous TX/RX..
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Michael Lo <michael.lo@mediatek.com>
Link: https://patch.msgid.link/20250505233618.1951021-1-sean.wang@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Modify MCU command sending functions to wait for a response,
ensuring consistent behavior across all commands and improves
reliability by confirming that each command is processed
successfully.
Fixes: c948b5da6b ("wifi: mt76: mt7925: add Mediatek Wi-Fi7 driver for mt7925 chips")
Signed-off-by: Michael Lo <michael.lo@mediatek.com>
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Link: https://patch.msgid.link/20250414013954.1151774-3-mingyen.hsieh@mediatek.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove a duplicate call to `mt76_mcu_send_msg` to fix redundant operations
in the sniffer command handling.
Fixes: c948b5da6b ("wifi: mt76: mt7925: add Mediatek Wi-Fi7 driver for mt7925 chips")
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Link: https://patch.msgid.link/20250414013954.1151774-2-mingyen.hsieh@mediatek.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add a check to ensure only one scan command is active at a time
by testing the MT76_HW_SCANNING state.
Fixes: c948b5da6b ("wifi: mt76: mt7925: add Mediatek Wi-Fi7 driver for mt7925 chips")
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Link: https://patch.msgid.link/20250414013954.1151774-1-mingyen.hsieh@mediatek.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
devm_ioremap() returns NULL on error. Currently, mt7915_mmio_wed_init()
does not check for this case, which results in a NULL pointer
dereference.
Prevent null pointer dereference in mt7915_mmio_wed_init().
Fixes: 4f831d18d1 ("wifi: mt76: mt7915: enable WED RX support")
Signed-off-by: Henry Martin <bsdhenrymartin@gmail.com>
Link: https://patch.msgid.link/20250407061900.85317-1-bsdhenrymartin@gmail.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
devm_ioremap() returns NULL on error. Currently, mt7996_mmio_wed_init()
does not check for this case, which results in a NULL pointer
dereference.
Prevent null pointer dereference in mt7996_mmio_wed_init()
Fixes: 83eafc9251 ("wifi: mt76: mt7996: add wed tx support")
Signed-off-by: Henry Martin <bsdhenrymartin@gmail.com>
Link: https://patch.msgid.link/20250407032349.83360-1-bsdhenrymartin@gmail.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce mt76_connac_mcu_build_rnr_scan_param routine for handling
RNR scan. This is a preliminary patch to enable RNR scan in mt7921 and
mt7925 driver.
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Link: https://patch.msgid.link/20250321013829.3598-1-mingyen.hsieh@mediatek.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Few updates to the Arm FVP(Fixed Virtual Platform) device tree, enhancing
support for system tracing, power management, and firmware coexistence:
1. ETE and TRBE support
Adds CoreSight ETE and TRBE nodes for the FVP Rev C model. These are
disabled by default as they need to be enabled explicitly via model
parameters.
2. CPU idle states and system timer for idle broadcast
Introduces CPU idle state definitions but disabled by default due to
potential performance impact on the model. Also adds a system-level
broadcast timer for use when CPUs enter deep idle states where local
timers stop.
3. Firmware memory reservation
Reserves 64MB at the end of the first DRAM bank to prevent conflicts
with FF-A firmware or similar configurations that rely on this region.
4. Drop the unnecessary clock-frequency property in the timer nodes
The boot/secure firmware must configure the timer clock frequency and
the non-secure OS must be able to read the same. The clock-frequency is
generally used when the firmware is broken which is not the case on
most of the fast models and Juno platform.
As noted above some of the changes are disabled by default where applicable
to ensure backward compatibility and avoid unintended performance impact
on platforms using default model parameters.
-----BEGIN PGP SIGNATURE-----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=dPTB
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=oTg4
-----END PGP SIGNATURE-----
Merge tag 'juno-updates-6.16' of https://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into soc/dt
Armv8 Juno/FVP updates for v6.16
Few updates to the Arm FVP(Fixed Virtual Platform) device tree, enhancing
support for system tracing, power management, and firmware coexistence:
1. ETE and TRBE support
Adds CoreSight ETE and TRBE nodes for the FVP Rev C model. These are
disabled by default as they need to be enabled explicitly via model
parameters.
2. CPU idle states and system timer for idle broadcast
Introduces CPU idle state definitions but disabled by default due to
potential performance impact on the model. Also adds a system-level
broadcast timer for use when CPUs enter deep idle states where local
timers stop.
3. Firmware memory reservation
Reserves 64MB at the end of the first DRAM bank to prevent conflicts
with FF-A firmware or similar configurations that rely on this region.
4. Drop the unnecessary clock-frequency property in the timer nodes
The boot/secure firmware must configure the timer clock frequency and
the non-secure OS must be able to read the same. The clock-frequency is
generally used when the firmware is broken which is not the case on
most of the fast models and Juno platform.
As noted above some of the changes are disabled by default where applicable
to ensure backward compatibility and avoid unintended performance impact
on platforms using default model parameters.
* tag 'juno-updates-6.16' of https://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
arm64: dts: fvp: Add ETE and TRBE nodes for Rev C model
arm64: dts: arm: Drop the clock-frequency property from timer nodes
arm64: dts: fvp: Reserve 64MB for the FF-A firmware in memory map
arm64: dts: fvp: Add CPU idle states for Rev C model
arm64: dts: fvp: Add system timer for broadcast during CPU idle
Link: https://lore.kernel.org/r/20250513143827.3606686-1-sudeep.holla@arm.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The subsystem-internal header pci.h still contains the function
prototype of pcim_intx(), which has since been made public in the global
header.
Remove the redundant function prototype.
Signed-off-by: Philipp Stanner <phasta@kernel.org>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20250522084626.150148-2-phasta@kernel.org
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEn/sM2K9nqF/8FWzzDHRl3/mQkZwFAmgtivcTHG1rbEBwZW5n
dXRyb25peC5kZQAKCRAMdGXf+ZCRnHdfB/9xpi2QMYgjWn5CWHaRT5JAt1BTVTAW
g7W1iddSkw18T/+FalxSjYPZKoE+6k2AcI/VTLbjEnv4bOPlmE48dItB8WsQnwHc
1Jjbvc861HTYL51UuYH3oqXH4MrY2BiPk2aoCOuT7vPDsn/PISbfIZ41eBK3noTS
TCY3DLV7u6tnureaCqGnl2M9lBfgF86rtn+d5vza2IFDu49b2J+Cv41CRkEIbP9P
kujiCAxStN+neCKd1LtZgFbmfy63xUujPtZR2h0oYiOK9X/Nz2bjmFu40zyC+vCn
z9P0oSXx2yaJCHiDrdzMM1McHhdpU4rNjVlYMKFQBNy/WfEvFHt+Eydy
=dV2M
-----END PGP SIGNATURE-----
Merge tag 'linux-can-fixes-for-6.15-20250521' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2025-05-22
this is a pull request of 4 patches for net/main.
The first 3 patches are by Axel Forsman and fix a ISR race condition
in the kvaser_pciefd driver.
The last patch is by Carlos Sanchez and fixes the reception of short
error messages in the slcan driver.
* tag 'linux-can-fixes-for-6.15-20250521' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can:
can: slcan: allow reception of short error messages
can: kvaser_pciefd: Continue parsing DMA buf after dropped RX
can: kvaser_pciefd: Fix echo_skb race
can: kvaser_pciefd: Force IRQ edge in case of nested IRQ
====================
Link: https://patch.msgid.link/20250522082344.490913-1-mkl@pengutronix.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Commit 5b39db6037 ("arm64: el2_setup.h: Rename some labels to be more
diff-friendly") reworked the labels in __init_el2_fgt to say what's
skipped rather than what the target location is. The exception was
"set_fgt_" which is where registers are written. In reviewing the BRBE
additions, Will suggested "set_debug_fgt_" where HDFGxTR_EL2 are
written. Doing that would partially revert commit 5b39db6037 undoing
the goal of minimizing additions here, but it would follow the
convention for labels where registers are written.
So let's do both. Branches that skip something go to a "skip" label and
places that set registers have a "set" label. This results in some
double labels, but it makes things entirely consistent.
While we're here, the SME skip label was incorrectly named, so fix it.
Reported-by: Will Deacon <will@kernel.org>
Cc: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://lore.kernel.org/r/20250520-arm-brbe-v19-v22-2-c1ddde38e7f8@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
