Convert the majority of MSM8916/39-based boards, which use UART2 with 2
pins (TX, RX) for the debug UART console. This adds the needed bias-pull-up
and bootph-all properties to avoid garbage input when UART is disconnected.
apq8016-schneider-hmibsc.dts does not use UART2 as a debug console, so it's
left as-is in this commit.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Link: https://lore.kernel.org/r/20250422-msm8916-console-pinctrl-v2-3-f345b7a53c91@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
At the moment, msm8916/39.dtsi have two inconsistent UART pinctrl templates
that are used by all the boards:
- &blsp_uart1_default configures all 4 pins (TX, RX, CTS, RTS), some
boards then limit this to just RX and TX
- &blsp_uart2_default only configures 2 pins (TX, RX), even though UART2
also supports CTS/RTS
It's difficult to define a generic pinctrl template for all UART use cases,
since they are quite different in practice. The main use case for most of
the 40+ MSM8916/39-based boards upstream is the UART debug console. The
current generic template is lacking some properties to work properly:
- bias-pull-up for RX: Generally, UART is push-pull and does not need pull
up/down. Both sides drive TX, so RX should never be floating. This is
why the current pinctrl in msm8916/39.dtsi uses bias-disable. However,
this assumes that UART is always connected. For the debug console this
will be rarely the case on mobile devices, only during debugging
sessions. The rest of the time, the RX pin is floating.
This has never caused massive problems, but it's obvious now that this
needs fixing:
(1) In U-Boot, we have been fighting with problems with autoboot for
years. Most of the time, there is a single \0 byte ("break event")
read during boot, which interrupts the autoboot process. I tried to
work around that by inserting some random delay [1], but it turned
out this is also not working reliably on all boards.
What happens is: Since RX is floating, it switches randomly between
high or low. A long low state is interpreted as "break event" (\0).
(2) In postmarketOS, we used to have the "magic SysRq key" enabled by
default for the serial console. We had to disable this at some
point, because there was a small number of users who were reporting
sysrq spam in the kernel log, possibly even crashes/panics
triggered by sysrq.
What likely happened is: SysRq is triggered by sending a "break
event", like in (1). With enough luck, you could even trigger any
of the SysRq actions if the RX pin switches between high and low
(e.g. because of noise introduced by the LTE radio close by).
We can fix this using bias-pull-up, but this may be unneeded,
unexpected, or even unwanted for other UART use cases.
- bootph-all: U-Boot needs to know which pinctrl to apply during early
boot stages, so we should specify "bootph-all" for the console UART
pinctrl. Without bootph-all, the bias-pull-up won't be applied early
enough in U-Boot to avoid the problem with autoboot in point (1) above.
It doesn't make sense to specify this for the other UART instances.
bootph-all is a generic property documented in dt-schema bootph.yaml.
Define these two additional properties only for the debug UART console, by
defining a new pinctrl template specifically for that. In the following
commits, boards will be converted to use these where appropriate.
[1]: ad7e967738
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Link: https://lore.kernel.org/r/20250422-msm8916-console-pinctrl-v2-2-f345b7a53c91@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
In preparation of adding a new console UART specific pinctrl template, move
the pinctrl reference to the board DT part. This forces people porting new
boards to consider what exactly they need for their board.
No functional change for the boards upstream.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Link: https://lore.kernel.org/r/20250422-msm8916-console-pinctrl-v2-1-f345b7a53c91@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
WoA devices using x1e/x1p use android firmware to boot, which notably
includes Gunyah hypervisor. This means that, so far, Linux-based OS
could only boot in EL1 on those devices.
However Windows can replace Gunyah upon boot with it's own hypervisor,
and with the use of tools such as "slbounce", it's possible to do the
same for Linux-based OS, in which case some modifications to the DT are
necessary to facilitate the absence of Gunyah services.
Add a EL2-specific DT overlay and apply it to x1e/x1p WoA devices to
create -el2.dtb for each of them alongside "normal" dtb.
Signed-off-by: Nikita Travkin <nikita@trvn.ru>
Link: https://lore.kernel.org/r/20250503-sc-el2-overlays-v2-5-24e9b4572e15@trvn.ru
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
x1e80100 has an SMMUv3 connected to PCIe which is normally controlled by
Gunyah and is thus transparent to the OS. However if we boot Linux in
EL2, without Gunyah, we need to manage this IOMMU ourselves. To make
that easier, and since the hardware actually exists, just not "usually"
managed by Linux, describe it in the dts as "reserved".
Signed-off-by: Nikita Travkin <nikita@trvn.ru>
Link: https://lore.kernel.org/r/20250503-sc-el2-overlays-v2-4-24e9b4572e15@trvn.ru
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
WoA devices using sc8280xp use android firmware to boot, which notably
includes QHEE hypervisor. This means that, so far, Linux-based OS could
only boot in EL1 on those devices.
However Windows can replace QHEE upon boot with it's own hypervisor, and
with the use of tools such as "slbounce", it's possible to do the same
for Linux-based OS, in which case some modifications to the DT are
necessary to facilitate the absence of QHEE services.
Add a EL2-specific DT overlay and apply it to sc8280xp WoA devices to
create -el2.dtb for each of them alongside "normal" dtb.
Signed-off-by: Nikita Travkin <nikita@trvn.ru>
Link: https://lore.kernel.org/r/20250503-sc-el2-overlays-v2-3-24e9b4572e15@trvn.ru
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
sc8280xp has an SMMUv3 connected to PCIe which is normally controlled by
QHEE and is thus transparent to the OS. However if we boot Linux in EL2,
without QHEE, we need to manage this IOMMU ourselves. To make that
easier, and since the hardware actually exists, just not "usually"
managed by Linux, describe it in the dts as "reserved".
Signed-off-by: Nikita Travkin <nikita@trvn.ru>
Link: https://lore.kernel.org/r/20250503-sc-el2-overlays-v2-2-24e9b4572e15@trvn.ru
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
WoA devices using sc7180 use android firmware to boot, which notably
includes QHEE hypervisor. This means that, so far, Linux-based OS could
only boot in EL1 on those devices.
However Windows can replace QHEE upon boot with it's own hypervisor, and
with the use of tools such as "slbounce", it's possible to do the same
for Linux-based OS, in which case some modifications to the DT are
necessary to facilitate the absence of QHEE services.
Add a EL2-specific DT overlay and apply it to sc7180 WoA devices to
create -el2.dtb for each of them alongside "normal" dtb.
Signed-off-by: Nikita Travkin <nikita@trvn.ru>
Link: https://lore.kernel.org/r/20250503-sc-el2-overlays-v2-1-24e9b4572e15@trvn.ru
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Convert the OpenRISC OMPIC interrupt controller binding to schema
format. It's a straight-forward conversion of the typical interrupt
controller.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Stafford Horne <shorne@gmail.com>
Merge series from Stefan Binding <sbinding@opensource.cirrus.com>:
CS35L63 is a Mono Class-D PC Smart Amplifier, with Speaker Protection
and Audio Enhancement Algorithms.
CS35L63 uses a similar control interface to CS35L56 so support for
it can be added into the CS35L56 driver.
CS35L63 only has SoundWire and I2C control interfaces.
Merge series from Bard Liao <yung-chuan.liao@linux.intel.com>:
SOF will load the function topologies by default. However, user may want
to use the monolithic topology. Add a flag amd a module parameter to
allow user specify the topology or not using function topologies.
Merge series from Charles Keepax <ckeepax@opensource.cirrus.com>:
Fix a small bug that can cause the sof_sdw machine driver to fail probe
after the first time it has probed. Also do some minor tidy up on the
handling of the platform_component of the dai links.
Merge series from "Peng Fan (OSS)" <peng.fan@oss.nxp.com>:
This patchset is separate from [1], and not merging changes in one
patch. So separate changes into three patches for each chip.
- sort headers
- Drop legacy platform support
- Convert to GPIO descriptors
of_gpio.h is deprecated, update the driver to use GPIO descriptors.
- Use devm_gpiod_get_optional to get GPIO descriptor with default
polarity GPIOD_OUT_LOW, set consumer name.
- Use gpiod_set_value_cansleep to configure output value.
I not have platforms to test, just do the patches with my best efforts,
and make build pass.
[1] https://lore.kernel.org/all/20250408-asoc-gpio-v1-0-c0db9d3fd6e9@nxp.com/
I put devlist.h into the wrong Makefile macro ("obj") to get it included
in "targets". Put it into "always" so nothing tries to link against it.
Solves CONFIG_EISA=y i386 build failure:
ld: vmlinux.a: member drivers/eisa/devlist.h in archive is not an object
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Closes: https://lore.kernel.org/all/4a8ba1d0-d2d9-41f8-abf1-d45ec8996d10@infradead.org
Fixes: dd09eb0e2c ("EISA: Increase length of device names")
Signed-off-by: Kees Cook <kees@kernel.org>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://lore.kernel.org/r/20250423023743.work.350-kees@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add RFI_CONFIG_CMD into the names array to facilitate the
display of this command name when sending it to the firmware.
Signed-off-by: Pagadala Yesu Anjaneyulu <pagadala.yesu.anjaneyulu@intel.com>
Reviewed-by: Somashekhar Puttagangaiah <somashekhar.puttagangaiah@intel.com>
Link: https://patch.msgid.link/20250505215513.da89484cb838.I755709232f5e441ca159bdc5a151bac73d9744d3@changeid
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
This sets both fwrt->uats_valid and returns 0, but in the
static inline it returns 0 without setting uats_valid,
which is confusing and the iwlmvm code misbehaves in this
case.
Since it already sets uats_valid, just remove the extra
return value.
Reported-by: Bjoern A. Zeeb <bz@FreeBSD.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://patch.msgid.link/20250505215513.e981a7911228.Ic94b5e03e2053a08b84cabeb58ce3b6598fd9fc6@changeid
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
In order to set the CDB indication in the dump meta data, we read it from
a specific prph register.
There is a known issue with that register in Xnj setups - in that case it
will always indicate CDB.
Instead of detecting the jacket case and then hardcode whether the CDB
indication should or shouldn't be set (according the CRF),
we can retrieve the CDB bit from the hw_rf_id (CSR_HW_RF_ID).
There is also no reason to do it conditionally only for ax210 / BnJ.
Cleanup the code a bit.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Link: https://patch.msgid.link/20250505215513.ea542a6c189e.I3d8cf5103b3747dfdd89985b45b592e419f97b63@changeid
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
This was used for debug/bringup of 8000 devices, to be able to
unify between all 8000 devices with NVM override. However, this
is really no longer used, those are ancient devices by now, so
we can remove the logic.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://patch.msgid.link/20250505215513.6210ac6cda09.I83cc3e68f0ed99a922d435c203fef840a28eb0de@changeid
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Add a debugfs option to use the ptp clock time for Rx device
timestamps on a monitor interface. This can be useful for e.g.
synchronizing multiple NICs or reporting the timestamp in the
system clock instead of the GP2.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Link: https://patch.msgid.link/20250505215513.fffe6718fbca.I75f034005851a2d0c8ba5b015b9fdcad8a7c550d@changeid
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Currently, there are two log messages at INFO level for
synchronous commands:
Attempting to send sync command ...
Setting HCMD_ACTIVE for command ...
and unfortunately none at all for async ones. Add one
for async commands as well.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://patch.msgid.link/20250505215512.cc4457285889.I633fae8828e8a37bbebc578166f388dcf893f592@changeid
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
If there is an ongoing scan that lasts long, the MPDU counters may not
increase enough due the device being busy with scanning and not
because we are in a low throughput scenario.
In that case we don't want to block EMLSR.
Instead, stop checking the counters from the moment we started
scanning, and when the scan ends - clear the counters and schedule a
check in 5 seconds, as usual.
Note that this is only done for regular scan since MLO scan is too short
to affect the counters, and scheduled scan is mainly used when we are
not connected.
Also note that we only stop checking whether to block EMLSR, and not if to
unblock.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Link: https://patch.msgid.link/20250505215512.330ea440d19c.Ib10dae0b7a0cb0e10c59a9edf5ff7af0f065ac60@changeid
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
There's no need to build a list of individual configs
first and then compare them, we can just go through all
of them and compare if the pointers aren't the same.
The complexity (in terms of number of comparisons) is a
bit higher that way, but it's just a test and the code
complexity is much lower without that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250504132447.85911c59d96a.I540f464229da3566d1726dfb61b46002fbb73bde@changeid
For different MACs we maintain the configs in different
files, and while it's a small waste of space, this is a
worthwhile trade-off for maintenance and simplicity. So
allow different MAC types to have the same config. This
could allow the same config for two MACs in the same MAC
family, but that's not hugely important. Also simplify
the test to not build a config list, there's no good
reason to do that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250504132447.27f5d570eb32.I1649309a0e54a1d446a38c5b2124a582de9f6d61@changeid
No hardware that uses iwlmvm actually supports HT greenfield.
Remove the support and then clean up the v1 rate API by doing
a conversion to v2 rate API, the only thing v1 covered that
couldn't be done in v2 was HT greenfield.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250504132447.805ec090c61f.Iafd87f62ceb463b72f861a5348078999dcaace92@changeid
This is ephemeral data that's passed from the alive
response to the PNVM loading, so it doesn't need to
be stored. Pass it around instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250504132447.fe8be4454007.I24824f35620b21fe49e9243818c7188e431af48e@changeid
This really belongs there, it's needed early, so move it. Remove
the related but dead iwl_trans_pcie_ctx_info_gen3_set_step() while
at it. In iwlmld move the calls since they do part of the trans
configuration.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250504132447.a4681ee11dd7.I6434a13d51932e984bb07695bc1cb931ebdcd27c@changeid
Instead of having a trans_configure method that copies all
the data, just have the users set up the configuration in
the transport directly. This simplifies the code on both
sides. While doing so also move some value from the trans
struct into the conf struct because they are configuration.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250504132447.e2a2535ecfd0.I21653103ff02afc5a4d97a41b68021f053985e37@changeid
Add a new device information 'info' substruct to the transport
that's const and can only be set by a special helper, and move
some information there.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250503224232.cd80cb55403c.Ic18524b66d655fad734bf97192a54d9cfa9fdf1f@changeid
We pass this parameter around a lot of places just to
validate what the firmware told us against the hardware
with a warning, which seems to never trigger. Remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250503224232.5405014d7f88.I3b74a1fd51a39c6df5674f2994189092d1635e7f@changeid
The rate validation in mac80211 considers a rate to be valid iff both
the rate index and the count are positive. When the rate scaling is
managed in the driver and not enough traffic passed to set the actual
rate, the driver set the rate to be the optimal rate. However, the rate
count is not set and thus the rate is considered not valid. Fix it by
setting the count to 1.
Fixes: 3e99b4d282 ("wifi: mac80211: Sanity check tx bitrate if not provided by driver")
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250503224232.0d1d1e022d63.I76833c14ba1d66f9bea5c32b25a54d8b36f229ba@changeid
