Move flow control register configuration from
lan78xx_update_flowcontrol() into a new helper function
lan78xx_configure_flowcontrol(). This separates hardware-specific
programming from policy logic and simplifies the upcoming phylink
integration.
The values used in this initial version of
lan78xx_configure_flowcontrol() are taken over as-is from the original
implementation to avoid functional changes. While they may not be
optimal for all USB and link speed combinations, they are known to work
reliably. Optimization of pause time and thresholds based on runtime
conditions can be done in a separate follow-up patch.
The forward declaration of lan78xx_configure_flowcontrol() will also be
removed later during the phylink conversion.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the USB link power configuration logic from lan78xx_link_reset()
to a new helper function lan78xx_configure_usb(). This simplifies the
main link reset path and isolates USB-specific logic.
The new function handles U1/U2 enablement based on Ethernet link speed,
but only for SuperSpeed-capable devices (LAN7800 and LAN7801). LAN7850,
a High-Speed-only device, is explicitly excluded. A warning is logged
if SuperSpeed is reported unexpectedly for LAN7850.
Add a forward declaration for lan78xx_configure_usb() as preparation for
the upcoming phylink conversion, where it will also be used from the
mac_link_up() callback.
Open questions remain:
- Why is the 1000 Mbps configuration split into two steps (U2 disable,
then U1 enable), unlike the single-step config used for 10/100 Mbps?
- U1/U2 behavior appears to depend on proper EEPROM configuration.
There are known devices in the field without EEPROM. Should the driver
enforce safe defaults in such cases?
Due to lack of USB subsystem expertise, no changes were made to this logic
beyond structural refactoring.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the PHY interrupt acknowledgment logic from lan78xx_link_reset()
to a new helper function lan78xx_phy_int_ack(). This simplifies the
code and prepares for reusing the acknowledgment logic independently
from the full link reset process, such as when using phylink.
No functional change intended.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Thangaraj Samynathan <thangaraj.s@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extract the LED enable logic based on the "microchip,led-modes"
property into a new helper function lan78xx_configure_leds_from_dt().
This simplifies lan78xx_phy_init() and improves modularity.
No functional changes intended.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Thangaraj Samynathan <thangaraj.s@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split out PHY detection into lan78xx_get_phy() and MAC-side setup into
lan78xx_mac_prepare_for_phy(), making the main lan78xx_phy_init() cleaner
and easier to follow.
This improves separation of concerns and prepares the code for a future
transition to phylink. Fixed PHY registration and interface selection
are now handled in lan78xx_get_phy(), while MAC-side delay configuration
is done in lan78xx_mac_prepare_for_phy().
The fixed PHY fallback is preserved for setups like EVB-KSZ9897-1,
where LAN7801 connects directly to a KSZ switch without a standard PHY
or device tree support.
No functional changes intended.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Thangaraj Samynathan <thangaraj.s@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RGMII timing correctness relies on the PHY providing internal delays.
This is typically ensured via PHY driver, strap pins, or PCB layout.
Explicitly checking for a PHY driver here is unnecessary and non-standard.
This logic applies to all MACs, not just LAN78xx, and should be left to
phylib, phylink, or platform configuration.
Drop the check and rely on standard subsystem behavior.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Thangaraj Samynathan <thangaraj.s@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ensure that return values from `lan78xx_write_reg()`,
`lan78xx_read_reg()`, and `phy_find_first()` are properly checked and
propagated. Use `ERR_PTR(ret)` for error reporting in
`lan7801_phy_init()` and replace `-EIO` with `-ENODEV` where appropriate
to provide more accurate error codes.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Thangaraj Samynathan <thangaraj.s@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
"Acoustic Tuning" debugfs node is a bridge to the acoustic tuning tool
which can tune the chips' acoustic effect.
Signed-off-by: Shenghao Ding <shenghao-ding@ti.com>
Link: https://patch.msgid.link/20250507094616.210-1-shenghao-ding@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
With commit bcb5d6c769 ("s390/pci: introduce lock to synchronize state
of zpci_dev's") the code to ignore power off of a PF that has child VFs
was changed from a direct return to a goto to the unlock and
pci_dev_put() section. The change however left the existing pci_dev_put()
untouched resulting in a doubple put. This can subsequently cause a use
after free if the struct pci_dev is released in an unexpected state.
Fix this by removing the extra pci_dev_put().
Cc: stable@vger.kernel.org
Fixes: bcb5d6c769 ("s390/pci: introduce lock to synchronize state of zpci_dev's")
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Reviewed-by: Gerd Bayer <gbayer@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
The zpci_create_device() function returns an error pointer that needs to
be checked before dereferencing it as a struct zpci_dev pointer. Add the
missing check in __clp_add() where it was missed when adding the
scan_list in the fixed commit. Simply not adding the device to the scan
list results in the previous behavior.
Cc: stable@vger.kernel.org
Fixes: 0467cdde8c ("s390/pci: Sort PCI functions prior to creating virtual busses")
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Reviewed-by: Gerd Bayer <gbayer@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
In preparation for making the kmalloc family of allocators type aware,
we need to make sure that the returned type from the allocation matches
the type of the variable being assigned. (Before, the allocator would
always return "void *", which can be implicitly cast to any pointer type.)
The assigned type is "struct i915_wa *". The returned type, while
technically matching, will be const qualified. As there is no general
way to remove const qualifiers, adjust the allocation type to match
the assignment.
Signed-off-by: Kees Cook <kees@kernel.org>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@linux.intel.com>
Link: https://lore.kernel.org/r/20250426061357.work.749-kees@kernel.org
As now UBSAN can be enabled, handle brk64 exits from UBSAN.
Re-use the decoding code from the kernel, and panic with
UBSAN message.
Signed-off-by: Mostafa Saleh <smostafa@google.com>
Reviewed-by: Kees Cook <kees@kernel.org>
Link: https://lore.kernel.org/r/20250430162713.1997569-5-smostafa@google.com
Signed-off-by: Marc Zyngier <maz@kernel.org>
Add a new Kconfig CONFIG_UBSAN_KVM_EL2 for KVM which enables
UBSAN for EL2 code (in protected/nvhe/hvhe) modes.
This will re-use the same checks enabled for the kernel for
the hypervisor. The only difference is that for EL2 it always
emits a "brk" instead of implementing hooks as the hypervisor
can't print reports.
The KVM code will re-use the same code for the kernel
"report_ubsan_failure()" so #ifdefs are changed to also have this
code for CONFIG_UBSAN_KVM_EL2
Signed-off-by: Mostafa Saleh <smostafa@google.com>
Reviewed-by: Kees Cook <kees@kernel.org>
Link: https://lore.kernel.org/r/20250430162713.1997569-4-smostafa@google.com
Signed-off-by: Marc Zyngier <maz@kernel.org>
report_ubsan_failure() doesn't use argument regs, and soon it will
be called from the hypervisor context were regs are not available.
So, remove the unused argument.
Signed-off-by: Mostafa Saleh <smostafa@google.com>
Acked-by: Kees Cook <kees@kernel.org>
Link: https://lore.kernel.org/r/20250430162713.1997569-3-smostafa@google.com
Signed-off-by: Marc Zyngier <maz@kernel.org>
Soon, KVM is going to use this logic for hypervisor panics,
so add it in a wrapper that can be used by the hypervisor exit
handler to decode hyp panics.
Signed-off-by: Mostafa Saleh <smostafa@google.com>
Reviewed-by: Kees Cook <kees@kernel.org>
Link: https://lore.kernel.org/r/20250430162713.1997569-2-smostafa@google.com
Signed-off-by: Marc Zyngier <maz@kernel.org>
UDF maintains total length of all extents in i_lenExtents. Generally we
keep extent lengths (and thus i_lenExtents) block aligned because it
makes the file appending logic simpler. However the standard mandates
that the inode size must match the length of all extents and thus we
trim the last extent when closing the file. To catch possible bugs we
also verify that i_lenExtents matches i_size when evicting inode from
memory. Commit b405c1e58b ("udf: refactor udf_next_aext() to handle
error") however broke the code updating i_lenExtents and thus
udf_evict_inode() ended up spewing lots of errors about incorrectly
sized extents although the extents were actually sized properly. Fix the
updating of i_lenExtents to silence the errors.
Fixes: b405c1e58b ("udf: refactor udf_next_aext() to handle error")
CC: stable@vger.kernel.org
Signed-off-by: Jan Kara <jack@suse.cz>
While telling the caller of pwm_set_waveform_might_sleep() if the
request was completed by rounding down only or (some) rounding up gives
additional information, it makes usage this function needlessly hard and
the additional information is not used. A prove for that is that
currently both users of this function just pass the returned value up to
their caller even though a positive value isn't intended there.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://lore.kernel.org/r/528cc3bbd9e35dea8646b1bcc0fbfe6c498bb4ed.1746010245.git.u.kleine-koenig@baylibre.com
Signed-off-by: Uwe Kleine-König <ukleinek@kernel.org>
Up to now pwm_set_waveform_might_sleep() returned 1 for exact requests
that couldn't be served exactly. In contrast to
pwm_round_waveform_might_sleep() and pwm_set_waveform_might_sleep() with
exact = false this is an error condition. So simplify handling for
callers of pwm_set_waveform_might_sleep() by returning -EDOM instead of
1 in this case.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://lore.kernel.org/r/20538a46719584dafd8a1395c886780a97dcdf79.1746010245.git.u.kleine-koenig@baylibre.com
Signed-off-by: Uwe Kleine-König <ukleinek@kernel.org>
remove_percpu_irq() has been unused since it was added in 2011 by
commit 31d9d9b6d8 ("genirq: Add support for per-cpu dev_id interrupts")
Remove it.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20250420164656.112641-1-linux@treblig.org
Octo Memory Manager driver (OMM) manages:
- the muxing between 2 OSPI busses and 2 output ports.
There are 4 possible muxing configurations:
- direct mode (no multiplexing): OSPI1 output is on port 1 and OSPI2
output is on port 2
- OSPI1 and OSPI2 are multiplexed over the same output port 1
- swapped mode (no multiplexing), OSPI1 output is on port 2,
OSPI2 output is on port 1
- OSPI1 and OSPI2 are multiplexed over the same output port 2
- the split of the memory area shared between the 2 OSPI instances.
- chip select selection override.
- the time between 2 transactions in multiplexed mode.
- check firewall access.
Signed-off-by: Christophe Kerello <christophe.kerello@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Link: https://lore.kernel.org/r/20250428-upstream_ospi_v6-v11-2-1548736fd9d2@foss.st.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Add bindings for STM32 Octo Memory Manager (OMM) controller.
OMM manages:
- the muxing between 2 OSPI busses and 2 output ports.
There are 4 possible muxing configurations:
- direct mode (no multiplexing): OSPI1 output is on port 1 and OSPI2
output is on port 2
- OSPI1 and OSPI2 are multiplexed over the same output port 1
- swapped mode (no multiplexing), OSPI1 output is on port 2,
OSPI2 output is on port 1
- OSPI1 and OSPI2 are multiplexed over the same output port 2
- the split of the memory area shared between the 2 OSPI instances.
- chip select selection override.
- the time between 2 transactions in multiplexed mode.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://lore.kernel.org/r/20250428-upstream_ospi_v6-v11-1-1548736fd9d2@foss.st.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Stubs in the header file for !CONFIG_STM32_FIREWALL case should be both
static and inline, because they do not come with earlier declaration and
should be inlined in every unit including the header.
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: stable@vger.kernel.org
Fixes: 5c9668cfc6 ("firewall: introduce stm32_firewall framework")
Link: https://lore.kernel.org/r/20250507092121.95121-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
With MMIO logging enabled, the MMIO access are traced and could be
sent to an STM device. Thus, an STM driver MMIO access could create
circular call chain with MMIO logging. Disable it for STM driver.
[] stm_source_write[stm_core]+0xc4
[] stm_ftrace_write[stm_ftrace]+0x40
[] trace_event_buffer_commit+0x238
[] trace_event_raw_event_rwmmio_rw_template+0x8c
[] log_post_write_mmio+0xb4
[] writel_relaxed[coresight_stm]+0x80
[] stm_generic_packet[coresight_stm]+0x1a8
[] stm_data_write[stm_core]+0x78
[] stm_source_write[stm_core]+0x7c
[] stm_ftrace_write[stm_ftrace]+0x40
[] trace_event_buffer_commit+0x238
[] trace_event_raw_event_rwmmio_read+0x84
[] log_read_mmio+0xac
[] readl_relaxed[coresight_tmc]+0x50
Signed-off-by: Mao Jinlong <quic_jinlmao@quicinc.com>
Reviewed-by: Leo Yan <leo.yan@arm.com>
Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Link: https://lore.kernel.org/r/20250506075743.1398257-1-quic_jinlmao@quicinc.com
On platforms with a static replicator, a kernel panic occurs during boot:
[ 4.999406] replicator_probe+0x1f8/0x360
[ 5.003455] replicator_platform_probe+0x64/0xd8
[ 5.008115] platform_probe+0x70/0xf0
[ 5.011812] really_probe+0xc4/0x2a8
[ 5.015417] __driver_probe_device+0x80/0x140
[ 5.019813] driver_probe_device+0xe4/0x170
[ 5.024032] __driver_attach+0x9c/0x1b0
[ 5.027900] bus_for_each_dev+0x7c/0xe8
[ 5.031769] driver_attach+0x2c/0x40
[ 5.035373] bus_add_driver+0xec/0x218
[ 5.039154] driver_register+0x68/0x138
[ 5.043023] __platform_driver_register+0x2c/0x40
[ 5.047771] coresight_init_driver+0x4c/0xe0
[ 5.052079] replicator_init+0x30/0x48
[ 5.055865] do_one_initcall+0x4c/0x280
[ 5.059736] kernel_init_freeable+0x1ec/0x3c8
[ 5.064134] kernel_init+0x28/0x1f0
[ 5.067655] ret_from_fork+0x10/0x20
A static replicator doesn't have registers, so accessing the claim
register results in a NULL pointer deference. Fixes the issue by
accessing the claim registers only after the I/O resource has been
successfully mapped.
Fixes: 7cd6368657 ("coresight: Clear self hosted claim tag on probe")
Signed-off-by: Leo Yan <leo.yan@arm.com>
Reviewed-by: James Clark <james.clark@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Link: https://lore.kernel.org/r/20250502111108.2726217-1-leo.yan@arm.com
Include linux/types.h before using bool.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202505070045.vWc04ygs-lkp@intel.com/
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Observe that i915->irq_lock is no longer used to protect anything
outside of display. Make it a display thing.
This allows us to remove the ugly #define irq_lock irq.lock hack from xe
compat header.
Note that this is slightly more subtle than it first looks. For i915,
there's no functional change here. The lock is moved. However, for xe,
we'll now have *two* locks, xe->irq.lock and display->irq.lock. These
should protect different things, though. Indeed, nesting in the past
would've lead to a deadlock because they were the same lock.
With the i915 references gone, we can make a handful more files
independent of i915_drv.h.
Reviewed-by: Gustavo Sousa <gustavo.sousa@intel.com>
Link: https://lore.kernel.org/r/6d8d2ce0f34a9c7361a5e2fcf96bb32a34c57e76.1746536745.git.jani.nikula@intel.com
[Jani: Fixed a comment while applying.]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Make the gt rps code and display irq code interact via
intel_display_rps.[ch], instead of direct access. Add no-op static
inline stubs for xe instead of having a separate build unit doing
nothing. All of this clarifies the interfaces between i915 core and
display.
Reviewed-by: Gustavo Sousa <gustavo.sousa@intel.com>
Link: https://lore.kernel.org/r/ef2a46dc8f30b72282494f54e98cb5fed7523b58.1746536745.git.jani.nikula@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
All users of vlv_display_irq_postinstall() outside of
intel_display_irq.c have a lock/unlock pair. Move the locking inside the
function. Add an unlocked variant for internal use, similar to the
_vlv_display_irq_reset() and vlv_display_irq_reset() functions.
Reviewed-by: Gustavo Sousa <gustavo.sousa@intel.com>
Link: https://lore.kernel.org/r/93ea785d2d9bdb4e18328aa42a00a492d9d783c0.1746536745.git.jani.nikula@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
I found this simple bug while preparing some patches for pKVM.
AFAICT, it should be harmless (besides crashing the kernel if it
was misbehaving)
Fixes: e94a7dea29 ("KVM: arm64: Move host page ownership tracking to the hyp vmemmap")
Signed-off-by: Mostafa Saleh <smostafa@google.com>
Link: https://lore.kernel.org/r/20250501162450.2784043-1-smostafa@google.com
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
HCRX_HOST_FLAGS, like most of these hardcoded setups, are not
a good match for options that can be selectively enabled or
disabled.
Nothing but the early setup is relying on it now, so kill the
macro and move the bag of bits where they belong.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20250430105916.3815157-3-maz@kernel.org
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
Rather than restoring HCRX_EL2 to a fixed value on vcpu exit,
perform a full save/restore of the register, ensuring that
we don't lose bits that would have been set at some point in
the host kernel lifetime, such as the GCSEn bit.
Fixes: ff5181d8a2 ("arm64/gcs: Provide basic EL2 setup to allow GCS usage at EL0 and EL1")
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20250430105916.3815157-2-maz@kernel.org
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
Use the new guards to get and lock the interrupt descriptor and tidy up the
code.
No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/all/20250429065422.670808288@linutronix.de
Use the new guards to get and lock the interrupt descriptor and tidy up the
code.
No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/all/20250429065422.612184618@linutronix.de
Use the new guards to get and lock the interrupt descriptor and tidy up the
code.
No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/all/20250429065422.552884529@linutronix.de
Use the new guards to get and lock the interrupt descriptor and tidy up the
code.
No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/all/20250429065422.494561120@linutronix.de
Use the new guards to get and lock the interrupt descriptor and tidy up the
code.
No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/all/20250429065422.435932527@linutronix.de
Use the new guards to get and lock the interrupt descriptor and tidy up the
code.
No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/all/20250429065422.376836282@linutronix.de
Use the new guards to get and lock the interrupt descriptor and tidy up the
code.
No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/all/20250429065422.315844964@linutronix.de
Use the new guards to get and lock the interrupt descriptor and tidy up the
code.
No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/all/20250429065422.258216558@linutronix.de
Use the new guards to get and lock the interrupt descriptor and tidy up the
code.
Make the return value boolean to reflect it's meaning.
No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/all/20250429065422.187250840@linutronix.de
