After power up, all SPI NAND's blocks are locked. Only read operations
are allowed, write and erase operations are forbidden.
The SPI NAND framework unlocks all the blocks during its initialization.
During a standby low power, the memory is powered down, losing its
configuration.
During the resume, the QSPI driver state is restored but the SPI NAND
framework does not reconfigured the memory.
This patch adds SPI-NAND MTD PM handlers for resume ops.
SPI NAND resume op re-initializes SPI NAND flash to its probed state.
Signed-off-by: Christophe Kerello <christophe.kerello@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210602094913.26472-4-patrice.chotard@foss.st.com
There are 2 timing registers:
- "data interface"
- "timings"
So far, the "data interface" register was named "timings" which begins
misleading when bringing support for the "timings" register. Rename it
to "data_iface".
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210527084959.208804-1-miquel.raynal@bootlin.com
Without the use of le16_to_cpu(), these accesses would have been wrong
on a big-endian machine.
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 45606518f9 ("mtd: rawnand: Add onfi_fill_nvddr_interface_config() helper")
Fixes: 9310668fb6 ("mtd: rawnand: Retrieve NV-DDR timing modes from the ONFI parameter page")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210527084913.208635-1-miquel.raynal@bootlin.com
Xilinx ZynqMP SoC and the Arasan controller support 64-bit DMA
addressing. Define the right mask otherwise the default is 32
and some accesses may overflow the default mask.
Reported-by: Jorge Courett <jorge.courett@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Jorge Courett <jorge.courett@gmail.com>
Link: https://lore.kernel.org/linux-mtd/20210527084548.208429-1-miquel.raynal@bootlin.com
I assumed that the combination of packet formats for MOTU 828 mk3 Hybrid
is the same as MOTU 828 mk3 FireWire. However at higher sampling rate, it
is different. MOTU 828 mk3 Hybrid has additional 4 dummy data chunks for
rx packet.
This commit fixes the issue to which I address at a commit f2ac3b8395
("ALSA: firewire-motu: sequence replay for source packet header").
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20210618040713.114611-1-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Below devices reports zero as the number of channels for external output
plug with MIDI type:
* Yamaha GO44/GO46
* Terratec Phase 24/X24
As a result, rx packet format is invalid and they generate silent sound.
This is a regression added in v5.13.
This commit fixes the bug, addressed at a commit 1bd1b3be86 ("ALSA:
bebob: perform sequence replay for media clock recovery").
Cc: <stable@vger.kernel.org>
Fixes: 5c6ea94f2b ("ALSA: bebob: detect the number of available MIDI ports")
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20210618040447.113306-1-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The HP EliteBook x360 830 G8 using ALC285 codec which using 0x04 to
control mute LED and 0x01 to control micmute LED.
Therefore, add a quirk to make it works.
Signed-off-by: Jeremy Szu <jeremy.szu@canonical.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210617171422.16652-1-jeremy.szu@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This reverts commit b4e326165e as the
patch series is causing build issues in linux-next at the moment.
Cc: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/YMuRcrE8xlWnFSWW@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 412981e062 as the
patch series is causing build issues in linux-next at the moment.
Cc: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/YMuRcrE8xlWnFSWW@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit c950686b38 as the
patch series is causing build issues in linux-next at the moment.
Cc: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/YMuRcrE8xlWnFSWW@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 1da8116eb0.
It causes merge issues with linux-next, and there are larger build
problems overall with this patch series, so the whole thing is being
reverted for now.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Link: https://lore.kernel.org/r/20210617144346.564be887@canb.auug.org.au
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On systems without any specific PMU driver support registered, running
perf record causes Oops.
The relevant portion from call trace:
BUG: Kernel NULL pointer dereference on read at 0x00000040
Faulting instruction address: 0xc0021f0c
Oops: Kernel access of bad area, sig: 11 [#1]
BE PAGE_SIZE=4K PREEMPT CMPCPRO
SAF3000 DIE NOTIFICATION
CPU: 0 PID: 442 Comm: null_syscall Not tainted 5.13.0-rc6-s3k-dev-01645-g7649ee3d2957 #5164
NIP: c0021f0c LR: c00e8ad8 CTR: c00d8a5c
NIP perf_instruction_pointer+0x10/0x60
LR perf_prepare_sample+0x344/0x674
Call Trace:
perf_prepare_sample+0x7c/0x674 (unreliable)
perf_event_output_forward+0x3c/0x94
__perf_event_overflow+0x74/0x14c
perf_swevent_hrtimer+0xf8/0x170
__hrtimer_run_queues.constprop.0+0x160/0x318
hrtimer_interrupt+0x148/0x3b0
timer_interrupt+0xc4/0x22c
Decrementer_virt+0xb8/0xbc
During perf record session, perf_instruction_pointer() is called to
capture the sample IP. This function in core-book3s accesses
ppmu->flags. If a platform specific PMU driver is not registered, ppmu
is set to NULL and accessing its members results in a crash. Fix this
crash by checking if ppmu is set.
Fixes: 2ca13a4cc5 ("powerpc/perf: Use regs->nip when SIAR is zero")
Cc: stable@vger.kernel.org # v5.11+
Reported-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Athira Rajeev <atrajeev@linux.vnet.ibm.com>
Tested-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/1623952506-1431-1-git-send-email-atrajeev@linux.vnet.ibm.com
Don't limit required_opp_table to genpd only. One possible use case is
cpufreq based devfreq governor, which can use required-opps property to
derive devfreq from cpufreq.
Though the OPP core still doesn't support non-genpd required-opps in
_set_required_opps().
Suggested-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
[ Viresh: Update _set_required_opps() to check for genpd ]
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Seems like 4d1b629861 ("selftests/bpf: Convert few tests to light skeleton.")
and 704e2beba2 ("selftests/bpf: Test ringbuf mmap read-only and read-write
restrictions") were done independently on bpf and bpf-next trees and are in
conflict with each other, despite a clean merge. Fix fetching of ringbuf's
map_fd to use light skeleton properly.
Fixes: 704e2beba2 ("selftests/bpf: Test ringbuf mmap read-only and read-write restrictions")
Fixes: 4d1b629861 ("selftests/bpf: Convert few tests to light skeleton.")
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20210618002824.2081922-1-andrii@kernel.org
There's little to no point in loading an EDAC driver running in a guest:
1) The CPU model reported by CPUID may not represent actual h/w
2) The hypervisor likely does not pass in access to memory controller devices
3) Hypervisors generally do not pass corrected error details to guests
Add a check in each of the Intel EDAC drivers for X86_FEATURE_HYPERVISOR
and simply return -ENODEV in the init routine.
Acked-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Link: https://lore.kernel.org/r/20210615174419.GA1087688@agluck-desk2.amr.corp.intel.com
Alder Lake SoC shares the same memory controller and In-Band ECC
(IBECC) IP with Tiger Lake SoC. Like Tiger Lake, it also has two
memory controllers each associated one IBECC instance. The minor
differences include the MMIO offset of each memory controller and
the type of memory error address logged in the IBECC.
So add Alder Lake compute die IDs, adjust the MMIO offset for each
memory controller and handle the type of memory error address logged
in the IBECC for Alder Lake EDAC support.
Tested-by: Vrukesh V Panse <vrukesh.v.panse@intel.com>
Signed-off-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Link: https://lore.kernel.org/r/20210611170123.1057025-7-tony.luck@intel.com
Tiger Lake SoC shares the same memory controller and In-Band ECC
(IBECC) IP with Elkhart Lake SoC. The main differences are that Tiger
Lake has two memory controllers each associated with one IBECC and
uses Machine Check for the memory error notification.
So add Tiger Lake compute die IDs, MCE decoding chain registration,
and memory slice decoding for Tiger Lake EDAC support.
Signed-off-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Link: https://lore.kernel.org/r/20210611170123.1057025-6-tony.luck@intel.com
The Ice Lake Neural Network Processor for Deep Learning Inference
(ICL-NNPI) SoC shares the same memory controller and In-Band ECC with
Elkhart Lake SoC. Add the ICL-NNPI compute die IDs for EDAC support.
Signed-off-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Link: https://lore.kernel.org/r/20210611170123.1057025-5-tony.luck@intel.com
A future Xeon processor will include in-package HBM (high bandwidth
memory). The in-package HBM memory controller shares the same
architecture with the regular DDR memory controller.
Add the HBM memory controller devices for EDAC support.
Tested-by: Hongyu Ning <hongyu.ning@linux.intel.com>
Signed-off-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Link: https://lore.kernel.org/r/20210611170123.1057025-4-tony.luck@intel.com
Current i10nm_edac driver is only for system configured in 1-level
memory. If the system is configured in 2-level memory, the driver
doesn't report the 1st level memory DIMM for the error address, even
if the error occurs in the 1st level memory.
Both Ice Lake servers and Sapphire Rapids servers can be configured
in 2-level memory. Add detection of memory levels to i10nm_edac for
the two kinds of servers so that the driver can report the 2nd level
memory DIMM or the 1st level memory DIMM according to error source.
Signed-off-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Link: https://lore.kernel.org/r/20210611170123.1057025-3-tony.luck@intel.com
Some Intel servers may configure memory in 2 levels, using
fast "near" memory (e.g. DDR) as a cache for larger, slower,
"far" memory (e.g. 3D X-point).
In these configurations the BIOS ADXL address translation for
an address in a 2-level memory range will provide details of
both the "near" and far components.
Current exported ADXL components are only for 1-level memory
system or for 2nd level memory of 2-level memory system. So
add new ADXL components for 1st level memory of 2-level memory
system to fully support 2-level memory system and the detection
of memory error source(1st level memory or 2nd level memory).
Signed-off-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Link: https://lore.kernel.org/r/20210611170123.1057025-2-tony.luck@intel.com
The current naming is confusing and wrong. The Register Locator is
identified by the DSVSEC identifier, not an offset.
Cc: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Ben Widawsky <ben.widawsky@intel.com>
Link: https://lore.kernel.org/r/20210618003009.956929-1-ben.widawsky@intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The ACPI CXL Early Discovery Table (CEDT) includes a list of CXL memory
resources in CXL Fixed Memory Window Structures (CFMWS). Retrieve each
CFMWS in the CEDT and add a cxl_decoder object to the root port (root0)
for each memory resource.
Signed-off-by: Alison Schofield <alison.schofield@intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Ben Widawsky <ben.widawsky@intel.com>
Link: https://lore.kernel.org/r/d2b73eecfb7ea22e1103f1894b271a89958b4c41.1623968958.git.alison.schofield@intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The base address for the Host Bridge port component registers is located
in the CXL Host Bridge Structure (CHBS) of the ACPI CXL Early Discovery
Table (CEDT). Retrieve the CHBS for each Host Bridge (ACPI0016 device)
and include that base address in the port object.
Co-developed-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Alison Schofield <alison.schofield@intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Ben Widawsky <ben.widawsky@intel.com>
Link: https://lore.kernel.org/r/a475ce137b899bc7ae5ba9550b5f198cb29ccbfd.1623968958.git.alison.schofield@intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
pcpu_balance_workfn() unconditionally calls pcpu_balance_free(),
pcpu_reclaim_populated(), pcpu_balance_populated() and
pcpu_balance_free() again.
Each call to pcpu_balance_free() and pcpu_reclaim_populated() will
cause at least one acquisition of the pcpu_lock. So even if the
balancing was scheduled because of a failed atomic allocation,
pcpu_lock will be acquired at least 4 times. This obviously
increases the contention on the pcpu_lock.
To optimize the scheme let's grab the pcpu_lock on the upper level
(in pcpu_balance_workfn()) and keep it generally locked for the whole
duration of the scheduled work, but release conditionally to perform
any slow operations like chunk (de)population and creation of new
chunks.
Signed-off-by: Roman Gushchin <guro@fb.com>
Signed-off-by: Dennis Zhou <dennis@kernel.org>
The kernel parameter for ftrace_dump_on_oops can take a single assignment.
That is, it can be:
ftrace_dump_on_oops or ftrace_dump_on_oops=orig_cpu
But the content in the sysctl file is a number.
0 for disabled
1 for ftrace_dump_on_oops (all CPUs)
2 for ftrace_dump_on_oops (orig CPU)
Allow the kernel command line to take a number as well to match the sysctl
numbers.
That is:
ftrace_dump_on_oops=1 is the same as ftrace_dump_on_oops
and
ftrace_dump_on_oops=2 is the same as ftrace_dump_on_oops=orig_cpu
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
reported by syzkaller ("KVM: x86: Immediately reset the MMU context when the SMM
flag is cleared").
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAmDLldwUHHBib256aW5p
QHJlZGhhdC5jb20ACgkQv/vSX3jHroPTOgf/XpAehLdWlx2877ulcBD0Kjt0tLvH
OFHRD1Ir0d1Ay3DX8qmxLquXHB4CoDGZBwi1d7AI165kUP/XLmV0bY6TZ74inI/P
CaD8Bsbm8+iBl5jrovEPc+223bK+3OFOvo2pk6M/MlsO/ExRikaPDtHOnkfousbl
nLX8v2qd7ihWyJOdLJMU9pV8E2iczQoCuH9yWBHdCrxRxWtPzkEekPWb0sujByiF
4tD7sqiEA3ugbF1Wm5keQV63NLplfxx+Zun0FV+tbpjjxQWAGl81dP+zmqok0sM/
qQCyZevt6jLLkL+Fn6hI6PP9OTeYreX2fgwhWXs71d2js33yNg5Veqx5Bw==
=Gs/y
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm fixes from Paolo Bonzini:
"Miscellaneous bugfixes.
The main interesting one is a NULL pointer dereference reported by
syzkaller ("KVM: x86: Immediately reset the MMU context when the SMM
flag is cleared")"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: selftests: Fix kvm_check_cap() assertion
KVM: x86/mmu: Calculate and check "full" mmu_role for nested MMU
KVM: X86: Fix x86_emulator slab cache leak
KVM: SVM: Call SEV Guest Decommission if ASID binding fails
KVM: x86: Immediately reset the MMU context when the SMM flag is cleared
KVM: x86: Fix fall-through warnings for Clang
KVM: SVM: fix doc warnings
KVM: selftests: Fix compiling errors when initializing the static structure
kvm: LAPIC: Restore guard to prevent illegal APIC register access
Function 'os_flush_stdout' is declared twice, so remove the
repeated declaration.
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Richard Weinberger <richard@nod.at>
Signed-off-by: Shaokun Zhang <zhangshaokun@hisilicon.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Fix to return a negative error code from the error handling case instead
of 0, as done elsewhere in this function.
Fixes: 89df6bfc04 ("uml: DEBUG_SHIRQ fixes")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Acked-By: anton.ivanov@cambridgegreys.com
Signed-off-by: Richard Weinberger <richard@nod.at>
Fix to return a negative error code from the error handling case instead
of 0, as done elsewhere in this function.
Fixes: a3c77c67a4 ("[PATCH] uml: slirp and slip driver cleanups and fixes")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Acked-By: anton.ivanov@cambridgegreys.com
Signed-off-by: Richard Weinberger <richard@nod.at>
GCC assumes that stack is aligned to 16-byte on call sites [1].
Since GCC 8, GCC began using 16-byte aligned SSE instructions to
implement assignments to structs on stack. When
CC_OPTIMIZE_FOR_PERFORMANCE is enabled, this affects
os-Linux/sigio.c, write_sigio_thread:
struct pollfds *fds, tmp;
tmp = current_poll;
Note that struct pollfds is exactly 16 bytes in size.
GCC 8+ generates assembly similar to:
movdqa (%rdi),%xmm0
movaps %xmm0,-0x50(%rbp)
This is an issue, because movaps will #GP if -0x50(%rbp) is not
aligned to 16 bytes [2], and how rbp gets assigned to is via glibc
clone thread_start, then function prologue, going though execution
trace similar to (showing only relevant instructions):
sub $0x10,%rsi
mov %rcx,0x8(%rsi)
mov %rdi,(%rsi)
syscall
pop %rax
pop %rdi
callq *%rax
push %rbp
mov %rsp,%rbp
The stack pointer always points to the topmost element on stack,
rather then the space right above the topmost. On push, the
pointer decrements first before writing to the memory pointed to
by it. Therefore, there is no need to have the stack pointer
pointer always point to valid memory unless the stack is poped;
so the `- sizeof(void *)` in the code is unnecessary.
On the other hand, glibc reserves the 16 bytes it needs on stack
and pops itself, so by the call instruction the stack pointer
is exactly the caller-supplied sp. It then push the 16 bytes of
the return address and the saved stack pointer, so the base
pointer will be 16-byte aligned if and only if the caller
supplied sp is 16-byte aligned. Therefore, the caller must supply
a 16-byte aligned pointer, which `stack + UM_KERN_PAGE_SIZE`
already satisfies.
On a side note, musl is unaffected by this issue because it forces
16 byte alignment via `and $-16,%rsi` in its clone wrapper.
Similarly, glibc i386 is also unaffected because it has
`andl $0xfffffff0, %ecx`.
To reproduce this bug, enable CONFIG_UML_RTC and
CC_OPTIMIZE_FOR_PERFORMANCE. uml_rtc will call
add_sigio_fd which will then cause write_sigio_thread to either go
into segfault loop or panic with "Segfault with no mm".
Similarly, signal stacks will be aligned by the host kernel upon
signal delivery. `- sizeof(void *)` to sigaltstack is
unconventional and extraneous.
On a related note, initialization of longjmp buffers do require
`- sizeof(void *)`. This is to account for the return address
that would have been pushed to the stack at the call site.
The reason for uml to respect 16-byte alignment, rather than
telling GCC to assume 8-byte alignment like the host kernel since
commit d9b0cde91c ("x86-64, gcc: Use
-mpreferred-stack-boundary=3 if supported"), is because uml links
against libc. There is no reason to assume libc is also compiled
with that flag and assumes 8-byte alignment rather than 16-byte.
[1] https://gcc.gnu.org/bugzilla/show_bug.cgi?id=40838
[2] https://c9x.me/x86/html/file_module_x86_id_180.html
Signed-off-by: YiFei Zhu <zhuyifei1999@gmail.com>
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Richard Weinberger <richard@nod.at>
vmalloc() heavy workloads in UML are extremely slow, due to
flushing the entire kernel VM space (flush_tlb_kernel_vm())
on the first segfault.
Implement flush_cache_vmap() to avoid that, and while at it
also add flush_cache_vunmap() since it's trivial.
This speeds up my vmalloc() heavy test of copying files out
from /sys/kernel/debug/gcov/ by 30x (from 30s to 1s.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-By: Anton Ivanov <anton.ivanov@cambridgegreys.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
The generic asm futex implementation emulates atomic access to
memory by doing a get_user followed by put_user. These translate
to two mapping operations on UML with paging enabled in the
meantime. This, in turn may end up changing interrupts,
invoking the signal loop, etc.
This replaces the generic implementation by a mapping followed
by an operation on the mapped segment.
Signed-off-by: Anton Ivanov <anton.ivanov@cambridgegreys.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
This patch enables the use of optimized xor routines from the x86
tree as well as the necessary fpu api shims so they can work on
UML.
Signed-off-by: Anton Ivanov <anton.ivanov@cambridgegreys.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
1. Reflect host cpu flags into the UML instance so they can
be used to select the correct implementations for xor, crypto, etc.
2. Reflect host cache alignment into UML instance. This is
important when running 32 bit on a 64 bit host as 32 bit by
default aligns to 32 while the actual alignment should be 64.
Ditto for some Xeons which align at 128.
Signed-off-by: Anton Ivanov <anton.ivanov@cambridgegreys.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
This tag contains a few small fixes, allows to build the Berlin reset
driver as a module, and adds stubs to the reset controller API to allow
compile-testing drivers outside of drivers/reset without enabling the
reset framework.
-----BEGIN PGP SIGNATURE-----
iI0EABYIADUWIQRRO6F6WdpH1R0vGibVhaclGDdiwAUCYMtFIxcccC56YWJlbEBw
ZW5ndXRyb25peC5kZQAKCRDVhaclGDdiwEIsAP4m0pQOBknwAy8IpNXhXzqcXd3d
fcFn36QGzMxA3CEI7QD+IQMxfKvCOZNUVKaDQa3azX6gvbooqsr8xl+5MYsHSQU=
=/q1G
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=AwL+
-----END PGP SIGNATURE-----
Merge tag 'reset-for-v5.14-2' of git://git.pengutronix.de/pza/linux into arm/drivers
Reset controller updates for v5.14, part2
This tag contains a few small fixes, allows to build the Berlin reset
driver as a module, and adds stubs to the reset controller API to allow
compile-testing drivers outside of drivers/reset without enabling the
reset framework.
* tag 'reset-for-v5.14-2' of git://git.pengutronix.de/pza/linux:
reset: Add compile-test stubs
reset: berlin: support module build
reset: bail if try_module_get() fails
reset: mchp: sparx5: fix return value check in mchp_sparx5_map_io()
reset: lantiq: use devm_reset_controller_register()
reset: hi6220: Use the correct HiSilicon copyright
Link: https://lore.kernel.org/r/14d33ac19b2a107e97ce1ab264987b707baa9ba7.camel@pengutronix.de
Signed-off-by: Olof Johansson <olof@lixom.net>
There doesn't seem to be any reason for the rpath being set in
the binaries, at on systems that I tested on. On the other hand,
setting rpath is actually harming binaries in some cases, e.g.
if using nix-based compilation environments where /lib & /lib64
are not part of the actual environment.
Add a new Kconfig option (under EXPERT, for less user confusion)
that allows disabling the rpath additions.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Sphinx 3.0 works at this point (albeit slowly) so stop scaring people
with a loud warning. We also don't need to babble about CJK support in the
LaTeX build.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>