Commit graph

1,031,458 commits

Author SHA1 Message Date
JC Kuo
971ee24706 usb: xhci: tegra: Enable ELPG for runtime/system PM
This commit implements the complete programming sequence for ELPG
entry and exit.

 1. At ELPG entry, invokes tegra_xusb_padctl_enable_phy_sleepwalk()
    and tegra_xusb_padctl_enable_phy_wake() to configure XUSB PADCTL
    sleepwalk and wake detection circuits to maintain USB lines level
    and respond to wake events (wake-on-connect, wake-on-disconnect,
    device-initiated-wake).

 2. At ELPG exit, invokes tegra_xusb_padctl_disable_phy_sleepwalk()
    and tegra_xusb_padctl_disable_phy_wake() to disarm sleepwalk and
    wake detection circuits.

At runtime suspend, XUSB host controller can enter ELPG to reduce
power consumption. When XUSB PADCTL wake detection circuit detects
a wake event, an interrupt will be raised. xhci-tegra driver then
will invoke pm_runtime_resume() for xhci-tegra.

Runtime resume could also be triggered by protocol drivers, this is
the host-initiated-wake event. At runtime resume, xhci-tegra driver
brings XUSB host controller out of ELPG to handle the wake events.

The same ELPG enter/exit procedure will be performed for system
suspend/resume path so USB devices can remain connected across SC7.

Signed-off-by: JC Kuo <jckuo@nvidia.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
2021-06-11 18:15:46 +02:00
JC Kuo
41a7426d25 usb: xhci: tegra: Unlink power domain devices
This commit unlinks xhci-tegra platform device with SS/host power
domain devices. Reasons for this change is - at ELPG entry, PHY
sleepwalk and wake configuration need to be done before powering
down SS/host partitions, and PHY need be powered off after powering
down SS/host partitions. Sequence looks like roughly below:

  tegra_xusb_enter_elpg() -> xhci_suspend()
                          -> enable PHY sleepwalk and wake if needed
                          -> power down SS/host partitions
                          -> power down PHY

If SS/host power domains are linked to xhci-tegra platform device, we
are not able to perform the sequence like above.

This commit introduces:
  1. tegra_xusb_unpowergate_partitions() to power up SS and host
     partitions together. If SS/host power domain devices are
     available, it invokes pm_runtime_get_sync() to request power
     driver to power up partitions; If power domain devices are not
     available, tegra_powergate_sequence_power_up() will be used to
     power up partitions.

  2. tegra_xusb_powergate_partitions() to power down SS and host
     partitions together. If SS/host power domain devices are
     available, it invokes pm_runtime_put_sync() to request power
     driver to power down partitions; If power domain devices are not
     available, tegra_powergate_power_off() will be used to power down
     partitions.

Signed-off-by: JC Kuo <jckuo@nvidia.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
2021-06-11 18:15:46 +02:00
Thierry Reding
23eca83155 Merge branch 'for-5.14/phy' into for-5.14/usb 2021-06-11 18:15:36 +02:00
Rafael J. Wysocki
84b7355b7a Merge back 'acpi-bus' material for v5.14. 2021-06-11 18:13:48 +02:00
Rafael J. Wysocki
bc8865ab32 Merge branch 'acpi-bus'
* acpi-bus:
  ACPI: Pass the same capabilities to the _OSC regardless of the query flag
2021-06-11 17:57:24 +02:00
Sean Christopherson
654430efde KVM: x86/mmu: Calculate and check "full" mmu_role for nested MMU
Calculate and check the full mmu_role when initializing the MMU context
for the nested MMU, where "full" means the bits and pieces of the role
that aren't handled by kvm_calc_mmu_role_common().  While the nested MMU
isn't used for shadow paging, things like the number of levels in the
guest's page tables are surprisingly important when walking the guest
page tables.  Failure to reinitialize the nested MMU context if L2's
paging mode changes can result in unexpected and/or missed page faults,
and likely other explosions.

E.g. if an L1 vCPU is running both a 32-bit PAE L2 and a 64-bit L2, the
"common" role calculation will yield the same role for both L2s.  If the
64-bit L2 is run after the 32-bit PAE L2, L0 will fail to reinitialize
the nested MMU context, ultimately resulting in a bad walk of L2's page
tables as the MMU will still have a guest root_level of PT32E_ROOT_LEVEL.

  WARNING: CPU: 4 PID: 167334 at arch/x86/kvm/vmx/vmx.c:3075 ept_save_pdptrs+0x15/0xe0 [kvm_intel]
  Modules linked in: kvm_intel]
  CPU: 4 PID: 167334 Comm: CPU 3/KVM Not tainted 5.13.0-rc1-d849817d5673-reqs #185
  Hardware name: ASUS Q87M-E/Q87M-E, BIOS 1102 03/03/2014
  RIP: 0010:ept_save_pdptrs+0x15/0xe0 [kvm_intel]
  Code: <0f> 0b c3 f6 87 d8 02 00f
  RSP: 0018:ffffbba702dbba00 EFLAGS: 00010202
  RAX: 0000000000000011 RBX: 0000000000000002 RCX: ffffffff810a2c08
  RDX: ffff91d7bc30acc0 RSI: 0000000000000011 RDI: ffff91d7bc30a600
  RBP: ffff91d7bc30a600 R08: 0000000000000010 R09: 0000000000000007
  R10: 0000000000000000 R11: 0000000000000000 R12: ffff91d7bc30a600
  R13: ffff91d7bc30acc0 R14: ffff91d67c123460 R15: 0000000115d7e005
  FS:  00007fe8e9ffb700(0000) GS:ffff91d90fb00000(0000) knlGS:0000000000000000
  CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
  CR2: 0000000000000000 CR3: 000000029f15a001 CR4: 00000000001726e0
  Call Trace:
   kvm_pdptr_read+0x3a/0x40 [kvm]
   paging64_walk_addr_generic+0x327/0x6a0 [kvm]
   paging64_gva_to_gpa_nested+0x3f/0xb0 [kvm]
   kvm_fetch_guest_virt+0x4c/0xb0 [kvm]
   __do_insn_fetch_bytes+0x11a/0x1f0 [kvm]
   x86_decode_insn+0x787/0x1490 [kvm]
   x86_decode_emulated_instruction+0x58/0x1e0 [kvm]
   x86_emulate_instruction+0x122/0x4f0 [kvm]
   vmx_handle_exit+0x120/0x660 [kvm_intel]
   kvm_arch_vcpu_ioctl_run+0xe25/0x1cb0 [kvm]
   kvm_vcpu_ioctl+0x211/0x5a0 [kvm]
   __x64_sys_ioctl+0x83/0xb0
   do_syscall_64+0x40/0xb0
   entry_SYSCALL_64_after_hwframe+0x44/0xae

Cc: Vitaly Kuznetsov <vkuznets@redhat.com>
Cc: stable@vger.kernel.org
Fixes: bf627a9288 ("x86/kvm/mmu: check if MMU reconfiguration is needed in init_kvm_nested_mmu()")
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210610220026.1364486-1-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2021-06-11 11:54:49 -04:00
Arnaldo Carvalho de Melo
36524112ab tools headers cpufeatures: Sync with the kernel sources
To pick the changes in:

  fb35d30fe5 ("x86/cpufeatures: Assign dedicated feature word for CPUID_0x8000001F[EAX]")
  e7b6385b01 ("x86/cpufeatures: Add Intel SGX hardware bits")
  1478b99a76 ("x86/cpufeatures: Mark ENQCMD as disabled when configured out")

That don't cause any change in the tools, just silences this perf build
warning:

  Warning: Kernel ABI header at 'tools/arch/x86/include/asm/disabled-features.h' differs from latest version at 'arch/x86/include/asm/disabled-features.h'
  diff -u tools/arch/x86/include/asm/disabled-features.h arch/x86/include/asm/disabled-features.h

Cc: Borislav Petkov <bp@suse.de>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Sean Christopherson <seanjc@google.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
2021-06-11 12:54:24 -03:00
Leo Yan
197eecb6ec perf session: Correct buffer copying when peeking events
When peeking an event, it has a short path and a long path.  The short
path uses the session pointer "one_mmap_addr" to directly fetch the
event; and the long path needs to read out the event header and the
following event data from file and fill into the buffer pointer passed
through the argument "buf".

The issue is in the long path that it copies the event header and event
data into the same destination address which pointer "buf", this means
the event header is overwritten.  We are just lucky to run into the
short path in most cases, so we don't hit the issue in the long path.

This patch adds the offset "hdr_sz" to the pointer "buf" when copying
the event data, so that it can reserve the event header which can be
used properly by its caller.

Fixes: 5a52f33adf ("perf session: Add perf_session__peek_event()")
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Jiri Olsa <jolsa@redhat.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lore.kernel.org/lkml/20210605052957.1070720-1-leo.yan@linaro.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
2021-06-11 12:54:24 -03:00
Wanpeng Li
dfdc0a714d KVM: X86: Fix x86_emulator slab cache leak
Commit c9b8b07cde (KVM: x86: Dynamically allocate per-vCPU emulation context)
tries to allocate per-vCPU emulation context dynamically, however, the
x86_emulator slab cache is still exiting after the kvm module is unload
as below after destroying the VM and unloading the kvm module.

grep x86_emulator /proc/slabinfo
x86_emulator          36     36   2672   12    8 : tunables    0    0    0 : slabdata      3      3      0

This patch fixes this slab cache leak by destroying the x86_emulator slab cache
when the kvm module is unloaded.

Fixes: c9b8b07cde (KVM: x86: Dynamically allocate per-vCPU emulation context)
Cc: stable@vger.kernel.org
Signed-off-by: Wanpeng Li <wanpengli@tencent.com>
Message-Id: <1623387573-5969-1-git-send-email-wanpengli@tencent.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2021-06-11 11:53:48 -04:00
Alper Gun
934002cd66 KVM: SVM: Call SEV Guest Decommission if ASID binding fails
Send SEV_CMD_DECOMMISSION command to PSP firmware if ASID binding
fails. If a failure happens after  a successful LAUNCH_START command,
a decommission command should be executed. Otherwise, guest context
will be unfreed inside the AMD SP. After the firmware will not have
memory to allocate more SEV guest context, LAUNCH_START command will
begin to fail with SEV_RET_RESOURCE_LIMIT error.

The existing code calls decommission inside sev_unbind_asid, but it is
not called if a failure happens before guest activation succeeds. If
sev_bind_asid fails, decommission is never called. PSP firmware has a
limit for the number of guests. If sev_asid_binding fails many times,
PSP firmware will not have resources to create another guest context.

Cc: stable@vger.kernel.org
Fixes: 59414c9892 ("KVM: SVM: Add support for KVM_SEV_LAUNCH_START command")
Reported-by: Peter Gonda <pgonda@google.com>
Signed-off-by: Alper Gun <alpergun@google.com>
Reviewed-by: Marc Orr <marcorr@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20210610174604.2554090-1-alpergun@google.com>
2021-06-11 11:52:48 -04:00
Jacob Keller
ea9b847cda ice: enable transmit timestamps for E810 devices
Add support for enabling Tx timestamp requests for outgoing packets on
E810 devices.

The ice hardware can support multiple outstanding Tx timestamp requests.
When sending a descriptor to hardware, a Tx timestamp request is made by
setting a request bit, and assigning an index that represents which Tx
timestamp index to store the timestamp in.

Hardware makes no effort to synchronize the index use, so it is up to
software to ensure that Tx timestamp indexes are not re-used before the
timestamp is reported back.

To do this, introduce a Tx timestamp tracker which will keep track of
currently in-use indexes.

In the hot path, if a packet has a timestamp request, an index will be
requested from the tracker. Unfortunately, this does require a lock as
the indexes are shared across all queues on a PHY. There are not enough
indexes to reliably assign only 1 to each queue.

For the E810 devices, the timestamp indexes are not shared across PHYs,
so each port can have its own tracking.

Once hardware captures a timestamp, an interrupt is fired. In this
interrupt, trigger a new work item that will figure out which timestamp
was completed, and report the timestamp back to the stack.

This function loops through the Tx timestamp indexes and checks whether
there is now a valid timestamp. If so, it clears the PHY timestamp
indication in the PHY memory, locks and removes the SKB and bit in the
tracker, then reports the timestamp to the stack.

It is possible in some cases that a timestamp request will be initiated
but never completed. This might occur if the packet is dropped by
software or hardware before it reaches the PHY.

Add a task to the periodic work function that will check whether
a timestamp request is more than a few seconds old. If so, the timestamp
index is cleared in the PHY, and the SKB is released.

Just as with Rx timestamps, the Tx timestamps are only 40 bits wide, and
use the same overall logic for extending to 64 bits of nanoseconds.

With this change, E810 devices should be able to perform basic PTP
functionality.

Future changes will extend the support to cover the E822-based devices.

Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2021-06-11 08:47:41 -07:00
Jacob Keller
77a781155a ice: enable receive hardware timestamping
Add SIOCGHWTSTAMP and SIOCSHWTSTAMP ioctl handlers to respond to
requests to enable timestamping support. If the request is for enabling
Rx timestamps, set a bit in the Rx descriptors to indicate that receive
timestamps should be reported.

Hardware captures receive timestamps in the PHY which only captures part
of the timer, and reports only 40 bits into the Rx descriptor. The upper
32 bits represent the contents of GLTSYN_TIME_L at the point of packet
reception, while the lower 8 bits represent the upper 8 bits of
GLTSYN_TIME_0.

The networking and PTP stack expect 64 bit timestamps in nanoseconds. To
support this, implement some logic to extend the timestamps by using the
full PHC time.

If the Rx timestamp was captured prior to the PHC time, then the real
timestamp is

  PHC - (lower_32_bits(PHC) - timestamp)

If the Rx timestamp was captured after the PHC time, then the real
timestamp is

  PHC + (timestamp - lower_32_bits(PHC))

These calculations are correct as long as neither the PHC timestamp nor
the Rx timestamps are more than 2^32-1 nanseconds old. Further, we can
detect when the Rx timestamp is before or after the PHC as long as the
PHC timestamp is no more than 2^31-1 nanoseconds old.

In that case, we calculate the delta between the lower 32 bits of the
PHC and the Rx timestamp. If it's larger than 2^31-1 then the Rx
timestamp must have been captured in the past. If it's smaller, then the
Rx timestamp must have been captured after PHC time.

Add an ice_ptp_extend_32b_ts function that relies on a cached copy of
the PHC time and implements this algorithm to calculate the proper upper
32bits of the Rx timestamps.

Cache the PHC time periodically in all of the Rx rings. This enables
each Rx ring to simply call the extension function with a recent copy of
the PHC time. By ensuring that the PHC time is kept up to date
periodically, we ensure this algorithm doesn't use stale data and
produce incorrect results.

To cache the time, introduce a kworker and a kwork item to periodically
store the Rx time. It might seem like we should use the .do_aux_work
interface of the PTP clock. This doesn't work because all PFs must cache
this time, but only one PF owns the PTP clock device.

Thus, the ice driver will manage its own kthread instead of relying on
the PTP do_aux_work handler.

With this change, the driver can now report Rx timestamps on all
incoming packets.

Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2021-06-11 08:47:41 -07:00
Jacob Keller
67569a7f94 ice: report the PTP clock index in ethtool .get_ts_info
Now that the driver registers a PTP clock device that represents the
clock hardware, it is important that the clock index is reported via the
ethtool .get_ts_info callback.

The underlying hardware resource is shared between multiple PF
functions. Only one function owns the hardware resources associated with
a timer, but multiple functions may be associated with it for the
purposes of timestamping.

To support this, the owning PF will store the clock index into the
driver shared parameters buffer in firmware. Other PFs will look up the
clock index by reading the driver shared parameter on demand when
requested via the .get_ts_info ethtool function.

In this way, all functions which are tied to the same timer are able to
report the clock index. Userspace software such as ptp4l performs
a look up on the netdev to determine the associated clock, and all
commands to control or configure the clock will be handled through the
controlling PF.

Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2021-06-11 08:47:41 -07:00
Jacob Keller
06c16d89d2 ice: register 1588 PTP clock device object for E810 devices
Add a new ice_ptp.c file for holding the basic PTP clock interface
functions. If the device supports PTP, call the new ice_ptp_init and
ice_ptp_release functions where appropriate.

If the function owns the hardware resource associated with the PTP
hardware clock, register with the PTP_1588_CLOCK infrastructure to
allocate a new clock object that represents the device hardware clock.

Implement basic functionality for reading and setting the clock time,
performing clock adjustments, and adjusting the clock frequency.

Future changes will introduce functionality for handling related
features including Tx and Rx timestamps.

Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2021-06-11 08:47:30 -07:00
Lakshmi Ramasubramanian
c67913492f ima: Fix warning: no previous prototype for function 'ima_add_kexec_buffer'
The function prototype for ima_add_kexec_buffer() is present
in 'linux/ima.h'.  But this header file is not included in
ima_kexec.c where the function is implemented.  This results
in the following compiler warning when "-Wmissing-prototypes" flag
is turned on:

  security/integrity/ima/ima_kexec.c:81:6: warning: no previous prototype
  for function 'ima_add_kexec_buffer' [-Wmissing-prototypes]

Include the header file 'linux/ima.h' in ima_kexec.c to fix
the compiler warning.

Fixes: dce92f6b11 (arm64: Enable passing IMA log to next kernel on kexec)
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Lakshmi Ramasubramanian <nramas@linux.microsoft.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mimi Zohar <zohar@linux.ibm.com>
2021-06-11 11:27:03 -04:00
Jiri Prchal
604288bc61 nvmem: eeprom: at25: fix type compiler warnings
Fixes:
	drivers/misc/eeprom/at25.c:181:28: warning: field width should have type 'int', but argument has type 'unsigned long'
	drivers/misc/eeprom/at25.c:386:13: warning: cast to smaller integer type 'int' from 'const void *'

Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Jiri Prchal <jiri.prchal@aksignal.cz>
Fixes: fd307a4ad3 ("nvmem: prepare basics for FRAM support")
Link: https://lore.kernel.org/r/20210611142706.27336-1-jiri.prchal@aksignal.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-06-11 16:42:41 +02:00
Jacob Keller
03cb4473be ice: add low level PTP clock access functions
Add the ice_ptp_hw.c file and some associated definitions to the ice
driver folder. This file contains basic low level definitions for
functions that interact with the device hardware.

For now, only E810-based devices are supported. The ice hardware
supports 2 major variants which have different PHYs with different
procedures necessary for interacting with the device clock.

Because the device captures timestamps in the PHY, each PHY has its own
internal timer. The timers are synchronized in hardware by first
preparing the source timer and the PHY timer shadow registers, and then
issuing a synchronization command. This ensures that both the source
timer and PHY timers are programmed simultaneously. The timers
themselves are all driven from the same oscillator source.

The functions in ice_ptp_hw.c abstract over the differences between how
the PHYs in E810 are programmed vs how the PHYs in E822 devices are
programmed. This series only implements E810 support, but E822 support
will be added in a future change.

Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2021-06-11 07:38:00 -07:00
Jacob Keller
7f9ab54d31 ice: add support for set/get of driver-stored firmware parameters
Depending on the device configuration, the ice hardware may share the
PTP hardware clock timer between multiple PFs. Each PF is informed by
firmware during initialization of the PTP timer association.

When bringing up PTP, only the PFs which own the timer shall allocate
a PTP hardware clock. Other PFs associated with that timer must report
the correct PTP clock index in order to allow userspace software the
ability to know which ports are connected to the same clock.

To support this, the firmware has driver shared parameters. These
parameters enable one PF to write the clock index into firmware, and
have other PFs read the associated value out. This enables the driver to
have only a single PF allocate and control the device timer registers,
while other PFs associated with that timer can report the correct clock
in the ETHTOOL_GET_TS_INFO report.

Add support for the necessary admin queue commands to enable reading and
writing of the driver shared parameters. This will be used in a future
change to enable sharing the PTP clock index between PF drivers.

Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2021-06-11 07:38:00 -07:00
Jacob Keller
9733cc94c5 ice: process 1588 PTP capabilities during initialization
The device firmware reports PTP clock capabilities to each PF during
initialization. This includes various information for both the overall
device and the individual function, including

For functions:
* whether this function has timesync enabled
* whether this function owns one of the 2 possible clock timers, and
  which one
* which timer the function is associated with
* the clock frequency, if the device supports multiple clock frequencies
* The GPIO pin association for the timer owned by this PF, if any

For the device:
* Which PF owns timer 0, if any
* Which PF owns timer 1, if any
* whether timer 0 is enabled
* whether timer 1 is enabled

Extract the bits from the capabilities information reported by firmware
and store them in the device and function capability structures.o

This information will be used in a future change to have the function
driver enable PTP hardware clock support.

Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2021-06-11 07:38:00 -07:00
Jacob Keller
8f5ee3c477 ice: add support for sideband messages
In order to support certain device features, including enabling the PTP
hardware clock, the ice driver needs to control some registers on the
device PHY.

These registers are accessed by sending sideband messages. For some
hardware, these messages must be sent over the device admin queue, while
other hardware has a dedicated control queue for the sideband messages.

Add the neighbor device message structure for sending a message to the
neighboring device. Where supported, initialize the sideband control
queue and handle cleanup.

Add a wrapper function for sending sideband control queue messages that
read or write a neighboring device register.

Because some devices send sideband messages over the AdminQ, also
increase the length of the admin queue to allow more messages to be
queued up. This is important because the sideband messages add
additional pressure on the AQ usage.

This support will be used in following patches to enable support for
CONFIG_1588_PTP_CLOCK.

Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2021-06-11 07:38:00 -07:00
Marc Zyngier
c51e96dace Merge branch irq/irqchip-driver-updates into irq/irqchip-next
Various minor irqchip driver updates:

- QC PDC now compiles as a module
- HiSilicon MBIGEN fix for compile-time warning when !ACPI

* irq/irqchip-driver-updates:
  irqchip/mbigen: Fix compile warning when CONFIG_ACPI is disabled
  irqchip/qcom-pdc: Switch to IRQCHIP_PLATFORM_DRIVER and allow as a module
2021-06-11 14:50:03 +01:00
Marc Zyngier
c64638d509 Merge branch irq/generic_handle_domain_irq-core into irq/irqchip-next
Simplify the handling of interrupts that require an IRQ domain
resolution:
- domains now cache the irqdata instead of the irq number
- consistent behaviour wrt RCU
- single lookup for architectures using sparse IRQs
- reduced boilerplate code in drivers.

* irq/generic_handle_domain_irq-core: (26 commits)
  irqchip: Bulk conversion to generic_handle_domain_irq()
  genirq: Move non-irqdomain handle_domain_irq() handling into ARM's handle_IRQ()
  genirq: Add generic_handle_domain_irq() helper
  irqchip/nvic: Convert from handle_IRQ() to handle_domain_irq()
  irqdesc: Fix __handle_domain_irq() comment
  genirq: Use irq_resolve_mapping() to implement __handle_domain_irq() and co
  irqdomain: Introduce irq_resolve_mapping()
  irqdomain: Protect the linear revmap with RCU
  irqdomain: Cache irq_data instead of a virq number in the revmap
  irqdomain: Use struct_size() helper when allocating irqdomain
  irqdomain: Make normal and nomap irqdomains exclusive
  powerpc: Move the use of irq_domain_add_nomap() behind a config option
  irqdomain: Reimplement irq_linear_revmap() with irq_find_mapping()
  irqdomain: Kill irq_domain_add_legacy_isa
  powerpc: Drop dependency between asm/irq.h and linux/irqdomain.h
  powerpc: Convert irq_domain_add_legacy_isa use to irq_domain_add_legacy
  scsi/ibmvscsi: Directly include linux/{of.h,irqdomain.h}
  powerpc: Add missing linux/{of.h,irqdomain.h} include directives
  MIPS: Do not include linux/irqdomain.h from asm/irq.h
  MIPS: Add missing linux/irqdomain.h includes
  ...
2021-06-11 14:32:12 +01:00
Marc Zyngier
cd273da34f Merge branch irq/irqchip-dt-updates into irq/irqchip-next
DT updates

* irq/irqchip-dt-updates:
  dt-bindings: interrupt-controller: arm,gic-v3: Describe GICv3 optional properties
  dt-bindings: irqchip: renesas-irqc: Add R-Car M3-W+ support
2021-06-11 14:31:04 +01:00
Lad Prabhakar
4e08a559a1 dt-bindings: interrupt-controller: arm,gic-v3: Describe GICv3 optional properties
Describe the optional GICv3 properties:
- clocks
- clock-names
- power-domains
- resets

Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210609155108.16590-1-prabhakar.mahadev-lad.rj@bp.renesas.com
2021-06-11 14:26:31 +01:00
Marc Zyngier
525ea1bc3b Merge branch irq/irqchip-spurious-printk into irq/irqchip-next
Drop a whole bunch of unnecessary printks on error paths

* irq/irqchip-spurious-printk:
  irqchip: gic-pm: Remove redundant error log of clock bulk
  irqchip/sun4i: Remove unnecessary oom message
  irqchip/irq-imx-gpcv2: Remove unnecessary oom message
  irqchip/imgpdc: Remove unnecessary oom message
  irqchip/gic-v3-its: Remove unnecessary oom message
  irqchip/gic-v2m: Remove unnecessary oom message
  irqchip/exynos-combiner: Remove unnecessary oom message
2021-06-11 14:24:55 +01:00
Chunfeng Yun
21a496179c irqchip: gic-pm: Remove redundant error log of clock bulk
There is error log in clk_bulk_prepare/enable()

Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/1617937474-24630-1-git-send-email-chunfeng.yun@mediatek.com
2021-06-11 14:21:04 +01:00
Zhen Lei
75768e391f irqchip/sun4i: Remove unnecessary oom message
Fixes scripts/checkpatch.pl warning:
WARNING: Possible unnecessary 'out of memory' message

Remove it can help us save a bit of memory.

Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210609141428.14737-1-thunder.leizhen@huawei.com
2021-06-11 14:19:51 +01:00
Zhen Lei
76fc40ec22 irqchip/irq-imx-gpcv2: Remove unnecessary oom message
Fixes scripts/checkpatch.pl warning:
WARNING: Possible unnecessary 'out of memory' message

Remove it can help us save a bit of memory.

Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210609141150.14637-1-thunder.leizhen@huawei.com
2021-06-11 14:19:47 +01:00
Zhen Lei
e3f389ed3a irqchip/imgpdc: Remove unnecessary oom message
Fixes scripts/checkpatch.pl warning:
WARNING: Possible unnecessary 'out of memory' message

Remove it can help us save a bit of memory.

Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210609140828.14584-1-thunder.leizhen@huawei.com
2021-06-11 14:19:43 +01:00
Zhen Lei
944a1a17d3 irqchip/gic-v3-its: Remove unnecessary oom message
Fixes scripts/checkpatch.pl warning:
WARNING: Possible unnecessary 'out of memory' message

Remove it can help us save a bit of memory.

Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210609140643.14531-1-thunder.leizhen@huawei.com
2021-06-11 14:19:39 +01:00
Zhen Lei
98ae089e1e irqchip/gic-v2m: Remove unnecessary oom message
Fixes scripts/checkpatch.pl warning:
WARNING: Possible unnecessary 'out of memory' message

Remove it can help us save a bit of memory.

Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210609140534.14478-1-thunder.leizhen@huawei.com
2021-06-11 14:19:32 +01:00
Zhen Lei
da30e6688d irqchip/exynos-combiner: Remove unnecessary oom message
Fixes scripts/checkpatch.pl warning:
WARNING: Possible unnecessary 'out of memory' message

Remove it can help us save a bit of memory.

Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210609140335.14425-1-thunder.leizhen@huawei.com
2021-06-11 14:19:27 +01:00
Florian Westphal
3ca5ca83e2 xfrm: merge dstopt and routing hdroff functions
Both functions are very similar, so merge them into one.

The nexthdr is passed as argument to break the loop in the
ROUTING case, this is the only header type where slightly different
rules apply.

While at it, the merged function is realigned with
ip6_find_1stfragopt().  That function received bug fixes for an infinite
loop, but neither dstopt nor rh parsing functions (copy-pasted from
ip6_find_1stfragopt) were changed.

Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
2021-06-11 14:48:51 +02:00
Florian Westphal
d1002d2490 xfrm: remove hdr_offset indirection
After previous patches all remaining users set the function pointer to
the same function: xfrm6_find_1stfragopt.

So remove this function pointer and call ip6_find_1stfragopt directly.

Reduces size of xfrm_type to 64 bytes on 64bit platforms.

Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
2021-06-11 14:48:50 +02:00
Florian Westphal
848b18fb7f xfrm: ipv6: move mip6_rthdr_offset into xfrm core
Place the call into the xfrm core.  After this all remaining users
set the hdr_offset function pointer to the same function which opens
the possiblity to remove the indirection.

Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
2021-06-11 14:48:50 +02:00
Florian Westphal
37b9e7eb55 xfrm: ipv6: move mip6_destopt_offset into xfrm core
This helper is relatively small, just move this to the xfrm core
and call it directly.

Next patch does the same for the ROUTING type.

Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
2021-06-11 14:48:50 +02:00
Florian Westphal
9acf4d3b9e xfrm: ipv6: add xfrm6_hdr_offset helper
This moves the ->hdr_offset indirect call to a new helper.

A followup patch can then modify the new function to replace
the indirect call by direct calls to the required hdr_offset helper.

Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
2021-06-11 14:48:50 +02:00
Marc Zyngier
46c886220a Merge branch kvm-arm64/mmu/reduce-vmemmap-overhead into kvmarm-master/next
Host stage-2 optimisations from Quentin Perret

* kvm-arm64/mmu/reduce-vmemmap-overhead:
  KVM: arm64: Use less bits for hyp_page refcount
  KVM: arm64: Use less bits for hyp_page order
  KVM: arm64: Remove hyp_pool pointer from struct hyp_page
  KVM: arm64: Unify MMIO and mem host stage-2 pools
  KVM: arm64: Remove list_head from hyp_page
  KVM: arm64: Use refcount at hyp to check page availability
  KVM: arm64: Move hyp_pool locking out of refcount helpers
2021-06-11 13:26:36 +01:00
Will Deacon
873c3e8977 arm64: Kill 32-bit applications scheduled on 64-bit-only CPUs
Scheduling a 32-bit application on a 64-bit-only CPU is a bad idea.

Ensure that 32-bit applications always take the slow-path when returning
to userspace on a system with mismatched support at EL0, so that we can
avoid trying to run on a 64-bit-only CPU and force a SIGKILL instead.

Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Link: https://lore.kernel.org/r/20210608180313.11502-5-will@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
2021-06-11 13:25:41 +01:00
Will Deacon
2f6a49bbc0 KVM: arm64: Kill 32-bit vCPUs on systems with mismatched EL0 support
If a vCPU is caught running 32-bit code on a system with mismatched
support at EL0, then we should kill it.

Acked-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Link: https://lore.kernel.org/r/20210608180313.11502-4-will@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
2021-06-11 13:25:40 +01:00
Will Deacon
2122a83331 arm64: Allow mismatched 32-bit EL0 support
When confronted with a mixture of CPUs, some of which support 32-bit
applications and others which don't, we quite sensibly treat the system
as 64-bit only for userspace and prevent execve() of 32-bit binaries.

Unfortunately, some crazy folks have decided to build systems like this
with the intention of running 32-bit applications, so relax our
sanitisation logic to continue to advertise 32-bit support to userspace
on these systems and track the real 32-bit capable cores in a cpumask
instead. For now, the default behaviour remains but will be tied to
a command-line option in a later patch.

Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Link: https://lore.kernel.org/r/20210608180313.11502-3-will@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
2021-06-11 13:25:40 +01:00
Will Deacon
930a58b409 arm64: cpuinfo: Split AArch32 registers out into a separate struct
In preparation for late initialisation of the "sanitised" AArch32 register
state, move the AArch32 registers out of 'struct cpuinfo' and into their
own struct definition.

Acked-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Link: https://lore.kernel.org/r/20210608180313.11502-2-will@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
2021-06-11 13:25:40 +01:00
Quentin Perret
6929586d8e KVM: arm64: Use less bits for hyp_page refcount
The hyp_page refcount is currently encoded on 4 bytes even though we
never need to count that many objects in a page. Make it 2 bytes to save
some space in the vmemmap.

As overflows are more likely to happen as well, make sure to catch those
with a BUG in the increment function.

Signed-off-by: Quentin Perret <qperret@google.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210608114518.748712-8-qperret@google.com
2021-06-11 13:24:12 +01:00
Quentin Perret
87ec060673 KVM: arm64: Use less bits for hyp_page order
The hyp_page order is currently encoded on 4 bytes even though it is
guaranteed to be smaller than this. Make it 2 bytes to reduce the hyp
vmemmap overhead.

Signed-off-by: Quentin Perret <qperret@google.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210608114518.748712-7-qperret@google.com
2021-06-11 13:24:11 +01:00
Quentin Perret
d978b9cfe6 KVM: arm64: Remove hyp_pool pointer from struct hyp_page
Each struct hyp_page currently contains a pointer to a hyp_pool struct
where the page should be freed if its refcount reaches 0. However, this
information can always be inferred from the context in the EL2 code, so
drop the pointer to save a few bytes in the vmemmap.

Signed-off-by: Quentin Perret <qperret@google.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210608114518.748712-6-qperret@google.com
2021-06-11 13:24:11 +01:00
Quentin Perret
7c350ea39e KVM: arm64: Unify MMIO and mem host stage-2 pools
We currently maintain two separate memory pools for the host stage-2,
one for pages used in the page-table when mapping memory regions, and
the other to map MMIO regions. The former is large enough to map all of
memory with page granularity and the latter can cover an arbitrary
portion of IPA space, but allows to 'recycle' pages.

However, this split makes accounting difficult to manage as pages at
intermediate levels of the page-table may be used to map both memory and
MMIO regions. Simplify the scheme by merging both pools into one. This
means we can now hit the -ENOMEM case in the memory abort path, but
we're still guaranteed forward-progress in the worst case by unmapping
MMIO regions. On the plus side this also means we can usually map a lot
more MMIO space at once if memory ranges happen to be mapped with block
mappings.

Signed-off-by: Quentin Perret <qperret@google.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210608114518.748712-5-qperret@google.com
2021-06-11 13:24:11 +01:00
Quentin Perret
914cde58a0 KVM: arm64: Remove list_head from hyp_page
The list_head member of struct hyp_page is only needed when the page is
attached to a free-list, which by definition implies the page is free.
As such, nothing prevents us from using the page itself to store the
list_head, hence reducing the size of the vmemmap.

Signed-off-by: Quentin Perret <qperret@google.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210608114518.748712-4-qperret@google.com
2021-06-11 13:24:11 +01:00
Quentin Perret
581982decc KVM: arm64: Use refcount at hyp to check page availability
The hyp buddy allocator currently checks the struct hyp_page list node
to see if a page is available for allocation or not when trying to
coalesce memory. Now that decrementing the refcount and attaching to
the buddy tree is done in the same critical section, we can rely on the
refcount of the buddy page to be in sync, which allows to replace the
list node check by a refcount check. This will ease removing the list
node from struct hyp_page later on.

Signed-off-by: Quentin Perret <qperret@google.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210608114518.748712-3-qperret@google.com
2021-06-11 13:24:11 +01:00
Quentin Perret
6cbf874e51 KVM: arm64: Move hyp_pool locking out of refcount helpers
The hyp_page refcount helpers currently rely on the hyp_pool lock for
serialization. However, this means the refcounts can't be changed from
the buddy allocator core as it already holds the lock, which means pages
have to go through odd transient states.

For example, when a page is freed, its refcount is set to 0, and the
lock is transiently released before the page can be attached to a free
list in the buddy tree. This is currently harmless as the allocator
checks the list node of each page to see if it is available for
allocation or not, but it means the page refcount can't be trusted to
represent the state of the page even if the pool lock is held.

In order to fix this, remove the pool locking from the refcount helpers,
and move all the logic to the buddy allocator. This will simplify the
removal of the list node from struct hyp_page in a later patch.

Signed-off-by: Quentin Perret <qperret@google.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210608114518.748712-2-qperret@google.com
2021-06-11 13:24:11 +01:00
Thierry Reding
c7289b1c8a arm64: tegra: Enable SMMU support on Tegra194
Add the device tree node for the dual-SMMU found on Tegra194 and hook up
peripherals such as host1x, BPMP, HDA, SDMMC, EQOS and VIC.

Signed-off-by: Thierry Reding <treding@nvidia.com>
2021-06-11 13:33:46 +02:00