Add serial support for RZ/G2L SoC with earlycon and
extended mode register support.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20210603221758.10305-11-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the hack to assign the global console_port variable at probe time.
This assumption that cons->index is -1 is wrong for systems that specify
'console=' in the cmdline (or 'stdout-path' in dts). Hence, on such system
the actual console assignment is ignored, and the first UART that happens
to be probed is used as console instead.
Move the logic to console_setup() and map the console to the correct port
through the array of available ports instead.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Link: https://lore.kernel.org/r/20210528133321.1859346-1-daniel@zonque.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
GEHC CS ONE (codename is PPD), has multiple microcontrollers connected
via UART controlling. UART2 is connected to an on-board microcontroller
at 19200 baud, which constantly pushes critical data (so aging character
detect interrupt will never trigger). This data must be processed at
50-200 Hz, so UART should return data in less than 5-20ms. With 1024
byte DMA buffer (and a constant data stream) the read operation instead
needs 1024 byte / 19200 baud = 53.333ms, which is way too long (note:
Worst case would be remote processor sending data with short pauses <=
7 characters, which would further increase this number). The current
downstream kernel instead configures 24 bytes resulting in 1.25ms, but
that is obviously not sensible for normal UART use cases and cannot be
used as new default.
The same device also has another microcontroller with a 4M baud connected
to UART5 exchanging lots of data. For this the same mechanism can be used
to increase the buffer size (downstream uses 4K instead of the default 1K)
with potentially slightly reduced buffer count. At this baud rate latency
is not an issue (4096 byte / 4M baud = 0.977 ms). Before increasing the
default buffer count from 4 to 16 in 76c38d30fe, this was required to
avoid data loss. With the changed default it's a performance optimization.
Signed-off-by: Fabien Lahoudere <fabien.lahoudere@collabora.com>
[replace commit message]
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20210430175038.103226-3-sebastian.reichel@collabora.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to optimize serial communication (performance/throughput VS
latency), we may need to tweak DMA period number and size. This adds
DT properties to configure those values before initialising DMA.
The defaults will stay the same as before.
[update documentation and commit message, rebase to current master,
switch back to DT instead of sysfs]
Signed-off-by: Fabien Lahoudere <fabien.lahoudere@collabora.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20210430175038.103226-2-sebastian.reichel@collabora.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function slot_handler_func() has very deep indentations. Moving the
poll handling into separate function could improve the readability.
Use the return value to keep the poll_needed handling at the same place.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Link: https://lore.kernel.org/r/1622735405-9980-17-git-send-email-stefan.wahren@i2se.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function parse_open() already has bail out sections like fail_open.
So use a goto for the other error cases like payload size is too small
and listening service cannot be found. This avoids two indentation levels.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Link: https://lore.kernel.org/r/1622735405-9980-14-git-send-email-stefan.wahren@i2se.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This moves the special handling for data messages from process_free_queue()
into a new function. After this process_free_queue() has less extreme
indentation and should be easier to read.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Link: https://lore.kernel.org/r/1622735405-9980-13-git-send-email-stefan.wahren@i2se.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During a recent review Dan Carpenter reported that the function naming of
(un)lock_service is misleading. They are like wrapper around kref_get /
kref_put and don't have anything to do with locking. So use a name which
represent more the actual behavior. Btw add the vchiq prefix to avoid
possible name conflicts.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Link: https://lore.kernel.org/r/1622735405-9980-12-git-send-email-stefan.wahren@i2se.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During a recent review Dan Carpenter noticed a double negation in a WARN_ON.
But a quick search revealed more unnecessary complex WARN_ON conditions.
This change should simplify them.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Link: https://lore.kernel.org/r/1622735405-9980-11-git-send-email-stefan.wahren@i2se.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
VCHIQ_MAKE_MSG isn't optimal because a lot of message types doesn't need
a parameter. So better define a macro for every message type which is used.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Link: https://lore.kernel.org/r/1622735405-9980-10-git-send-email-stefan.wahren@i2se.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The macro IS_POW2 is only used to ensure some size are powers of 2.
Better use BUILD_BUG_ON_NOT_POWER_OF_2 for this. Since this must be done
in a function, merge all these checks in a new function.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Link: https://lore.kernel.org/r/1622735405-9980-5-git-send-email-stefan.wahren@i2se.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit "staging: vchiq_core: avoid indention in poll_services_of_group"
tries to reduce the indention, but the parts regarding the third if statement
breaks the logic. So restore them and prevent vchiq_test from hanging during
the ping test.
Fixes: 2f440843a7 ("staging: vchiq_core: avoid indention in poll_services_of_group")
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Link: https://lore.kernel.org/r/1622735405-9980-2-git-send-email-stefan.wahren@i2se.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pcie node is being overlayed in 'gbpc1.dts' file requesting three
gpio reset pins for each pcie port. Gnubee only needs general
gpio 19 to properly reset and make all of them work. This pin
is already requested in the general 'mt7621.dtsi' file as well
as is the pinctrl pins. So we only need to enable the node
in the overlay and all the other stuff can be safely deleted.
Also, pin 8 is being requested for gpio-leds node and there
was an error on boot before this changes because of pin was
already assigned (EBUSY):
leds-gpio: probe of gpio-leds failed with error -16
With this changes this error has disappear and the board is
properly booting without any other regression.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20210604063031.13599-1-sergio.paracuellos@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These are only used by putting their address in an array of pointers to
const struct attribute_group (either directly or via the
__ATTRIBUTE_GROUP macro). Make them const to allow the compiler to place
them in read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Link: https://lore.kernel.org/r/20210528213408.20067-1-rikard.falkeborn@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 553671b768 ("firmware_loader: Fix labels with comma for builtin
firmware") added this line, which was unneeded.
The macro 'comma' is defined in scripts/Kbuild.include.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Link: https://lore.kernel.org/r/20210528173404.169764-1-masahiroy@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If user gave an event name explicitly, it should be displayed in the
output as is. But with --no-merge option it adds a pmu name at the
end so might confuse users.
Actually this is true for hybrid pmus, I think we should do the same
for others.
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Acked-by: Ian Rogers <irogers@google.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Jin Yao <yao.jin@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lore.kernel.org/lkml/20210602212241.2175005-3-namhyung@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
The evsel__clone() should copy all fields in the evsel which are set
during the event parsing. But it missed the use_config_name field.
Fixes: 12279429d8 ("perf stat: Uniquify hybrid event name")
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Acked-by: Ian Rogers <irogers@google.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Jin Yao <yao.jin@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lore.kernel.org/lkml/20210602212241.2175005-2-namhyung@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
VEXPRESS_CONFIG needs to either be missing, built-in, or modular when
pl111 is modular. Update the Kconfig to reflect the need.
Fixes: 4dc7c97d04 ("drm/pl111: depend on CONFIG_VEXPRESS_CONFIG")
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210604014055.4060521-1-keescook@chromium.org
Read the entire size of the buffer, including the trailing new line
character.
Discovered while reading the sched domain names of CPU0:
before:
cat /sys/kernel/debug/sched/domains/cpu0/domain*/name
SMTMCDIE
after:
cat /sys/kernel/debug/sched/domains/cpu0/domain*/name
SMT
MC
DIE
Fixes: 9af0440ec8 ("debugfs: Implement debugfs_create_str()")
Reviewed-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Link: https://lore.kernel.org/r/20210527091105.258457-1-dietmar.eggemann@arm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This avoids reimplementing the detection logic twice and removes the
possibility of activating charging with 500mA even if a battery is not
detected.
Signed-off-by: Carl Philipp Klemm <philipp@uvos.xyz>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This invalidates empty->counter_uah and charge_full when charge_now
indicates that they are grossly wrong and adds some tolerance to
POWER_SUPPLY_PROP_CHARGE_FULL to allow for inaccuracies in the charge
counter and manufacturing tolerances in the battery.
Signed-off-by: Carl Philipp Klemm <philipp@uvos.xyz>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Allow disabling and re-enabling battery charging of an axp209 PMIC
through a writable status property. With the current driver code
charging is always on.
This works on the axp209 of Banana {Pi M1+,Pro} and should work on all
AXP chips.
Signed-off-by: Hermann.Lauer@uni-heidelberg.de
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Similar to commit 25edcc50d7 ("KVM: PPC: Book3S HV: Save and restore
FSCR in the P9 path"), ensure the P7/8 path saves and restores the host
FSCR. The logic explained in that patch actually applies there to the
old path well: a context switch can be made before kvmppc_vcpu_run_hv
restores the host FSCR and returns.
Now both the p9 and the p7/8 paths now save and restore their FSCR, it
no longer needs to be restored at the end of kvmppc_vcpu_run_hv
Fixes: b005255e12 ("KVM: PPC: Book3S HV: Context-switch new POWER8 SPRs")
Cc: stable@vger.kernel.org # v3.14+
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Fabiano Rosas <farosas@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210526125851.3436735-1-npiggin@gmail.com
This patch adds a udc_async_callbacks handler to the net2272 UDC
driver, which will prevent a theoretical race during gadget unbinding.
The net2272 driver is sufficiently complicated that I didn't want to
mess around with IRQ settings. Instead, the patch simply adds a new
flag to control async callbacks, and checks the flag before issuing
any of them.
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20210520202206.GF1216852@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds a udc_async_callbacks handler to the net2280 UDC
driver, which will prevent a theoretical race during gadget unbinding.
The net2280 driver is sufficiently complicated that I didn't want to
mess around with IRQ settings. Instead, the patch simply adds a new
flag to control async callbacks, and checks the flag before issuing
any of them.
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20210520202200.GE1216852@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds a udc_async_callbacks handler to the dummy-hcd UDC
driver, which will prevent a theoretical race during gadget unbinding.
The implementation is simple, since dummy-hcd already has a flag to
keep track of whether emulated IRQs are enabled. All the handler has
to do is store the enable value in the flag, and avoid setting the
flag prematurely.
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20210520202152.GD1216852@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Gadget API has a theoretical race when a gadget driver is unbound.
Although the pull-up is turned off before the driver's ->unbind
callback runs, if the USB cable were to be unplugged at just the wrong
moment there would be nothing to prevent the UDC driver from invoking
the ->disconnect callback after the unbind has finished. In theory,
other asynchronous callbacks could also happen during the time before
the UDC driver's udc_stop routine is called, and the gadget driver
would not be prepared to handle any of them.
We need a way to tell UDC drivers to stop issuing asynchronous (that is,
->suspend, ->resume, ->disconnect, ->reset, or ->setup) callbacks at
some point after the pull-up has been turned off and before the
->unbind callback runs. This patch adds a new ->udc_async_callbacks
callback to the usb_gadget_ops structure for precisely this purpose,
and it adds the corresponding support to the UDC core.
Later patches in this series add support for udc_async_callbacks to
several UDC drivers.
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20210520202144.GC1216852@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the driver the interrupts are fetched by name. Therefore, add
interrupt names in the list of required properties
Fixes: 68989fe1c3 ("dt-bindings: usb: Convert cdns-usb3.txt to YAML schema")
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Link: https://lore.kernel.org/r/20210528060657.29100-1-a-govindraju@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dma_resv_lockdep() seems to have some space/tab mixups. Fix that and
move the function to the end of the file.
Also fix some minor things checkpatch.pl pointed out while at it.
No functional change.
Signed-off-by: Christian König <christian.koenig@amd.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20210602140359.272601-2-christian.koenig@amd.com
During unbind, ffs_func_eps_disable() will be executed, resulting in
completion callbacks for any pending USB requests. When using AIO,
irrespective of the completion status, io_data work is queued to
io_completion_wq to evaluate and handle the completed requests. Since
work runs asynchronously to the unbind() routine, there can be a
scenario where the work runs after the USB gadget has been fully
removed, resulting in accessing of a resource which has been already
freed. (i.e. usb_ep_free_request() accessing the USB ep structure)
Explicitly drain the io_completion_wq, instead of relying on the
destroy_workqueue() (in ffs_data_put()) to make sure no pending
completion work items are running.
Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/1621644261-1236-1-git-send-email-wcheng@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Like the state_machine_timer, we should also cancel possible pending
send discover identity hrtimer when unregister tcpm port.
Fixes: c34e85fa69 ("usb: typec: tcpm: Send DISCOVER_IDENTITY from dedicated work")
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Li Jun <jun.li@nxp.com>
Link: https://lore.kernel.org/r/1622627829-11070-3-git-send-email-jun.li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Like the state_machine_timer, we should also cancel possible pending
frs hrtimer when unregister tcpm port.
Fixes: 8dc4bd0736 ("usb: typec: tcpm: Add support for Sink Fast Role SWAP(FRS)")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Li Jun <jun.li@nxp.com>
Link: https://lore.kernel.org/r/1622627829-11070-2-git-send-email-jun.li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When receiving Alert Message, if it is not unexpected but is
unsupported for some reason, the port should return Not_Supported
Message response.
Also, according to PD3.0 Spec 6.5.2.1.4 Event Flags Field, the
OTP/OVP/OCP flags in the Event Flags field in Status Message no longer
require Get_PPS_Status Message to clear them. Thus remove it when
receiving Status Message with those flags being set.
In addition, add the missing AMS operations for Status Message.
Fixes: 64f7c494a3 ("typec: tcpm: Add support for sink PPS related messages")
Fixes: 0908c5aca3 ("usb: typec: tcpm: AMS and Collision Avoidance")
Signed-off-by: Kyle Tso <kyletso@google.com>
Link: https://lore.kernel.org/r/20210531164928.2368606-1-kyletso@google.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Syzbot managed to trigger this assert while performing its fuzzing.
Turns out it's better to have those asserts turned into full-fledged
checks so that in case buggy btrfs images are mounted the users gets
an error and mounting is stopped. Alternatively with CONFIG_BTRFS_ASSERT
disabled such image would have been erroneously allowed to be mounted.
Reported-by: syzbot+a6bf271c02e4fe66b4e4@syzkaller.appspotmail.com
CC: stable@vger.kernel.org # 5.4+
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
[ add uuids to the messages ]
Signed-off-by: David Sterba <dsterba@suse.com>