[ Upstream commit 70ad2e6bd1 ]
The headphone clamps cause fairly loud pops during type detect
because they sink current from the detection process itself. Disable
the clamps whilst the type detect runs, to improve the detection
pop performance.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/20250423090944.1504538-1-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e56088a137 ]
The public datasheets of the following Amlogic SoCs describe a typical
resistor value for the built-in pull up/down resistor:
- Meson8/8b/8m2: not documented
- GXBB (S905): 60 kOhm
- GXL (S905X): 60 kOhm
- GXM (S912): 60 kOhm
- G12B (S922X): 60 kOhm
- SM1 (S905D3): 60 kOhm
The public G12B and SM1 datasheets additionally state min and max
values:
- min value: 50 kOhm for both, pull-up and pull-down
- max value for the pull-up: 70 kOhm
- max value for the pull-down: 130 kOhm
Use 60 kOhm in the pinctrl-meson driver as well so it's shown in the
debugfs output. It may not be accurate for Meson8/8b/8m2 but in reality
60 kOhm is closer to the actual value than 1 Ohm.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/20250329190132.855196-1-martin.blumenstingl@googlemail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a9a69c3b38 ]
Incorrect types are used as sizeof() arguments in devm_kcalloc().
It should be sizeof(dai_link_data) for link_data instead of
sizeof(snd_soc_dai_link).
This is found by our static analysis tool.
Signed-off-by: Chenyuan Yang <chenyuan0y@gmail.com>
Link: https://patch.msgid.link/20250406210854.149316-1-chenyuan0y@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 41b4b11da0 ]
Check that all encoders attached to a given CRTC are valid
possible_clones of each other.
Signed-off-by: Jessica Zhang <quic_jesszhan@quicinc.com>
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20241216-concurrent-wb-v4-3-fe220297a7f0@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 749b5b279e ]
We have a few reports of sc7180-trogdor-pompom devices that have a
panel in them that IDs as STA 0x0004 and has the following raw EDID:
00 ff ff ff ff ff ff 00 4e 81 04 00 00 00 00 00
10 20 01 04 a5 1a 0e 78 0a dc dd 96 5b 5b 91 28
1f 52 54 00 00 00 01 01 01 01 01 01 01 01 01 01
01 01 01 01 01 01 8e 1c 56 a0 50 00 1e 30 28 20
55 00 00 90 10 00 00 18 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 fe
00 31 31 36 4b 48 44 30 32 34 30 30 36 0a 00 e6
We've been unable to locate a datasheet for this panel and our partner
has not been responsive, but all Starry eDP datasheets that we can
find agree on the same timing (delay_100_500_e200) so it should be
safe to use that here instead of the super conservative timings. We'll
still go a little extra conservative and allow `hpd_absent` of 200
instead of 100 because that won't add any real-world delay in most
cases.
We'll associate the string from the EDID ("116KHD024006") with this
panel. Given that the ID is the suspicious value of 0x0004 it seems
likely that Starry doesn't always update their IDs but the string will
still work to differentiate if we ever need to in the future.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20250109142853.1.Ibcc3009933fd19507cc9c713ad0c99c7a9e4fe17@changeid
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c5e3306a42 ]
msm is automagically upgrading normal commits to full modesets, and
that's a big no-no:
- for one this results in full on->off->on transitions on all these
crtc, at least if you're using the usual helpers. Which seems to be
the case, and is breaking uapi
- further even if the ctm change itself would not result in flicker,
this can hide modesets for other reasons. Which again breaks the
uapi
v2: I forgot the case of adding unrelated crtc state. Add that case
and link to the existing kerneldoc explainers. This has come up in an
irc discussion with Manasi and Ville about intel's bigjoiner mode.
Also cc everyone involved in the msm irc discussion, more people
joined after I sent out v1.
v3: Wording polish from Pekka and Thomas
Acked-by: Pekka Paalanen <pekka.paalanen@collabora.com>
Acked-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: David Airlie <airlied@gmail.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Pekka Paalanen <pekka.paalanen@collabora.com>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Simon Ser <contact@emersion.fr>
Cc: Manasi Navare <navaremanasi@google.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Abhinav Kumar <quic_abhinavk@quicinc.com>
Cc: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Simona Vetter <simona.vetter@intel.com>
Signed-off-by: Simona Vetter <simona.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20250108172417.160831-1-simona.vetter@ffwll.ch
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c852646f12 ]
Set no_i2s_capture and no_spdif_capture flags in hdmi_codec_pdata structure
to report that the ADV7511 HDMI bridge does not support i2s or spdif audio
capture.
Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20250108170356.413063-2-olivier.moysan@foss.st.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6788a66600 ]
End offset for the monitor destination ring descriptor is defined as
16 bits, while the firmware definition specifies only 12 bits.
The remaining bits (bit 12 to bit 15) are reserved and may contain
junk values, leading to invalid information retrieval. Fix this issue
by updating the correct genmask values.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Link: https://patch.msgid.link/20241223060132.3506372-8-quic_ppranees@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dfffb31751 ]
When using nvmem, ath9k could potentially be loaded before nvmem, which
loads after mtd. This is an issue if DT contains an nvmem mac address.
If nvmem is not ready in time for ath9k, -EPROBE_DEFER is returned. Pass
it to _probe so that ath9k can properly grab a potentially present MAC
address.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Link: https://patch.msgid.link/20241105222326.194417-1-rosenp@gmail.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8685520474 ]
During the initialization of the qaic device, pci_select_bars() is
used to fetch a bitmask of the BARs exposed by the device. On devices
that have Virtual Functions capabilities, the bitmask includes SR-IOV
BARs.
Use a mask to filter out SR-IOV BARs if they exist.
Signed-off-by: Youssef Samir <quic_yabdulra@quicinc.com>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Signed-off-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Reviewed-by: Lizhi Hou <lizhi.hou@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250117170943.2643280-6-quic_jhugo@quicinc.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit df11edfba4 ]
Since inception there is an obvious typo laying around in
ath12k_hal_tx_cmd_ext_desc_setup(). Instead of initializing + adding
flags to tcl_ext_cmd->info1, we initialize + override. This will be needed
in the future to make broadcast frames work with ethernet encapsulation.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Signed-off-by: Nicolas Escande <nico.escande@gmail.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250127071306.1454699-1-nico.escande@gmail.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5a6a461079 ]
Previously, the ad5398 driver used only platform_data, which is
deprecated in favour of device tree. This caused the AD5398 to fail to
probe as it could not load its init_data. If the AD5398 has a device
tree node, pull the init_data from there using
of_get_regulator_init_data.
Signed-off-by: Isaac Scott <isaac.scott@ideasonboard.com>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Link: https://patch.msgid.link/20250128173143.959600-4-isaac.scott@ideasonboard.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8978530645 ]
RXEMPTY can cause an IRQ, even though we may not do anything about it
(such as if we are waiting for more received data). We must still handle
these IRQs because we can tell they were caused by the device.
Signed-off-by: Sean Anderson <sean.anderson@linux.dev>
Link: https://patch.msgid.link/20250116224130.2684544-6-sean.anderson@linux.dev
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ebfc9199df ]
To ensure where are protected by driver mutex can also be protected by
wiphy_lock(), so afterward we can remove driver mutex safely.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250122060310.31976-2-pkshih@realtek.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 00451eb3be ]
Some users want to plug two identical USB devices at the same time.
This static variable could theoretically cause them to use incorrect
TX power values.
Move the variable to the caller and pass a pointer to it to
rtw8822b_set_tx_power_index_by_rate().
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/8a60f581-0ab5-4d98-a97d-dd83b605008f@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3d3e28feca ]
Occasionally there is an EPROTO error during firmware download.
This error is converted to EAGAIN in the download function.
But nobody tries again and so device probe fails.
Implement download retry to fix this.
This error was observed (and fix tested) on a tbs2910 board [1]
with an embedded RTL8188EU (0bda:8179) device behind a USB hub.
[1] arch/arm/boot/dts/nxp/imx/imx6q-tbs2910.dts
Signed-off-by: Soeren Moch <smoch@web.de>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250127194828.599379-1-smoch@web.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 598bdf4fef ]
Instead of using standard perf_event_attr->freq=0 and ->sample_period
fields, IBS event in 'sample period mode' can also be opened by setting
period value directly in perf_event_attr->config in a MaxCnt bit-field
format.
IBS OP MaxCnt bits are defined as:
(high bits) IbsOpCtl[26:20] = IbsOpMaxCnt[26:20]
(low bits) IbsOpCtl[15:0] = IbsOpMaxCnt[19:4]
Perf event sample period can be derived from MaxCnt bits as:
sample_period = (high bits) | ((low_bits) << 4);
However, current code just masks MaxCnt bits and shifts all of them,
including high bits, which is incorrect. Fix it.
Signed-off-by: Ravi Bangoria <ravi.bangoria@amd.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Namhyung Kim <namhyung@kernel.org>
Link: https://lkml.kernel.org/r/20250115054438.1021-4-ravi.bangoria@amd.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 46dcf85566 ]
IBS Op uses two counters: MaxCnt and CurCnt. MaxCnt is programmed with
the desired sample period. IBS hw generates sample when CurCnt reaches
to MaxCnt. The size of these counter used to be 20 bits but later they
were extended to 27 bits. The 7 bit extension is indicated by CPUID
Fn8000_001B_EAX[6 / OpCntExt].
perf_ibs->cnt_mask variable contains bit masks for MaxCnt and CurCnt.
But IBS driver does not set upper 7 bits of CurCnt in cnt_mask even
when OpCntExt CPUID bit is set. Fix this.
IBS driver uses cnt_mask[CurCnt] bits only while disabling an event.
Fortunately, CurCnt bits are not read from MSR while re-enabling the
event, instead MaxCnt is programmed with desired period and CurCnt is
set to 0. Hence, we did not see any issues so far.
Signed-off-by: Ravi Bangoria <ravi.bangoria@amd.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Namhyung Kim <namhyung@kernel.org>
Link: https://lkml.kernel.org/r/20250115054438.1021-5-ravi.bangoria@amd.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 21ee965267 ]
Currently in scmi_protocol_device_request(), no duplicate scmi device
name is allowed across any protocol. However scmi_dev_match_id() first
matches the protocol id and then the name. So, there is no strict
requirement to keep this scmi device name unique across all the protocols.
Relax the constraint on the duplicate name across the protocols and
inhibit only within the same protocol id.
Message-Id: <20250131141822.514342-1-sudeep.holla@arm.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0053f7d39d ]
The `readlink(path, buf, sizeof(buf))` call reads at most sizeof(buf)
bytes and *does not* append null-terminator to buf. With respect to
that, fix two pieces in get_fd_type:
1. Change the truncation check to contain sizeof(buf) rather than
sizeof(path).
2. Append null-terminator to buf.
Reported by Coverity.
Signed-off-by: Viktor Malik <vmalik@redhat.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Reviewed-by: Quentin Monnet <qmo@kernel.org>
Link: https://lore.kernel.org/bpf/20250129071857.75182-1-vmalik@redhat.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c81202906b ]
The ast driver looks up supplied display modes from an internal list of
display modes supported by the VBIOS.
Do not use the crtc_-prefixed display values from struct drm_display_mode
for looking up the VBIOS mode. The fields contain raw values that the
driver programs to hardware. They are affected by display settings like
double-scan or interlace.
Instead use the regular vdisplay and hdisplay fields for lookup. As the
programmed values can now differ from the values used for lookup, set
struct drm_display_mode.crtc_vdisplay and .crtc_hdisplay from the VBIOS
mode.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250131092257.115596-9-tzimmermann@suse.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f9a5c4b6af ]
Add a few missing registers from the readable register callback.
Suggested-by: Shuming Fan <shumingf@realtek.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.dev>
Link: https://patch.msgid.link/20250107154408.814455-6-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7d92a38d67 ]
As per codec device specification, 24-bit is allowed in provider mode.
Update the code to reflect that.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://patch.msgid.link/20250203141051.2361323-4-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 385a59e7f7 ]
Add clock-output-names property to clock nodes, so that the resulting
clock name do not change when clock node name is changed.
Also, replace underscores with hyphens in the clock node names as per
dt-schema rule.
Signed-off-by: Naman Trivedi <naman.trivedimanojbhai@amd.com>
Acked-by: Senthil Nathan Thangaraj <senthilnathan.thangaraj@amd.com>
Link: https://lore.kernel.org/r/20241122095712.1166883-1-naman.trivedimanojbhai@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d73a4bfa28 ]
Since "LED_KANA" was defined as "0x04", the shift number should be "4".
Signed-off-by: junan <junan76@163.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 268c73d470 ]
In case of MHI error a reset work will be queued which will try
napi_disable() after napi_synchronize().
As the napi will be only enabled after qmi_firmware_ready event,
trying napi_synchronize() before napi_enable() will result in
indefinite sleep in case of a firmware crash in QMI init sequence.
To avoid this, introduce napi_enabled flag to check if napi is enabled
or not before calling napi_synchronize().
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Avula Sri Charan <quic_asrichar@quicinc.com>
Signed-off-by: Tamizh Chelvam Raja <quic_tamizhr@quicinc.com>
Reviewed-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Link: https://patch.msgid.link/20250124090058.3194299-1-quic_tamizhr@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7081dc75df ]
Some of the allowed operations put the tape into a known position to
continue operation assuming only the tape position has changed. But reset
sets partition, density and block size to drive default values. These
should be restored to the values before reset.
Normally the current block size and density are stored by the drive. If
the settings have been changed, the changed values have to be saved by the
driver across reset.
Signed-off-by: Kai Mäkisara <Kai.Makisara@kolumbus.fi>
Link: https://lore.kernel.org/r/20250120194925.44432-2-Kai.Makisara@kolumbus.fi
Reviewed-by: John Meneghini <jmeneghi@redhat.com>
Tested-by: John Meneghini <jmeneghi@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f0842902b3 ]
Fix smatch warning regarding missed calls to free_irq(). Free the phba IRQ
in the failed pci_irq_vector cases.
lpfc_init.c: lpfc_sli4_enable_msi() warn: 'phba->pcidev->irq' from
request_irq() not released.
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Link: https://lore.kernel.org/r/20250131000524.163662-3-justintee8345@gmail.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 56c3d809b7 ]
After a port swap between separate fabrics, there may be multiple nodes in
the vport's fc_nodes list with the same fabric well known address.
Duplication is temporary and eventually resolves itself after dev_loss_tmo
expires, but nameserver queries may still occur before dev_loss_tmo. This
possibly results in returning stale fabric ndlp objects. Fix by adding an
nlp_state check to ensure the ndlp search routine returns the correct newer
allocated ndlp fabric object.
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Link: https://lore.kernel.org/r/20250131000524.163662-5-justintee8345@gmail.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5ec7e1c86c ]
Do not warn on missing pad_data when oob is in sgl.
Signed-off-by: Konstantin Taranov <kotaranov@microsoft.com>
Link: https://patch.msgid.link/1737394039-28772-9-git-send-email-kotaranov@linux.microsoft.com
Reviewed-by: Shiraz Saleem <shirazsaleem@microsoft.com>
Reviewed-by: Long Li <longli@microsoft.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c3a392bdd3 ]
Previous implementation assumes that there is 1:1 matching between
vectors and queues. It isn't always true.
Get minimum value from Rx/Tx queues to determine combined queues number.
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8ce939a0fa ]
The event may have been updated in the PMU-specific implementation,
e.g., Intel PEBS counters snapshotting. The common code should not
read and overwrite the value.
The PERF_SAMPLE_READ in the data->sample_type can be used to detect
whether the PMU-specific value is available. If yes, avoid the
pmu->read() in the common code. Add a new flag, skip_read, to track the
case.
Factor out a perf_pmu_read() to clean up the code.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20250121152303.3128733-3-kan.liang@linux.intel.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ad6b5b73ff ]
rcu_all_qs() is defined for !CONFIG_PREEMPT_RCU but the declaration
is conditioned on CONFIG_PREEMPTION.
With CONFIG_PREEMPT_LAZY, CONFIG_PREEMPTION=y does not imply
CONFIG_PREEMPT_RCU=y.
Decouple the two.
Cc: Paul E. McKenney <paulmck@kernel.org>
Reviewed-by: Frederic Weisbecker <frederic@kernel.org>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Ankur Arora <ankur.a.arora@oracle.com>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Boqun Feng <boqun.feng@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fcf0e25ad4 ]
rcu_read_unlock_strict() can be called with preemption enabled
which can make for an unstable rdp and a racy norm value.
Fix this by dropping the preempt-count in __rcu_read_unlock()
after the call to rcu_read_unlock_strict(), adjusting the
preempt-count check appropriately.
Suggested-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Ankur Arora <ankur.a.arora@oracle.com>
Reviewed-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Boqun Feng <boqun.feng@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 83b28cfe79 ]
With PREEMPT_RCU=n, cond_resched() provides urgently needed quiescent
states for read-side critical sections via rcu_all_qs().
One reason why this was needed: lacking preempt-count, the tick
handler has no way of knowing whether it is executing in a
read-side critical section or not.
With (PREEMPT_LAZY=y, PREEMPT_DYNAMIC=n), we get (PREEMPT_COUNT=y,
PREEMPT_RCU=n). In this configuration cond_resched() is a stub and
does not provide quiescent states via rcu_all_qs().
(PREEMPT_RCU=y provides this information via rcu_read_unlock() and
its nesting counter.)
So, use the availability of preempt_count() to report quiescent states
in rcu_flavor_sched_clock_irq().
Suggested-by: Paul E. McKenney <paulmck@kernel.org>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Ankur Arora <ankur.a.arora@oracle.com>
Reviewed-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Boqun Feng <boqun.feng@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a8c2d3932c ]
It can be needed to have some MSI-X allocated as static and rest as
dynamic. For example on PF VSI. We want to always have minimum one MSI-X
on it, because of that it is allocated as a static one, rest can be
dynamic if it is supported.
Change the ice_get_irq_res() to allow using static entries if they are
free even if caller wants dynamic one.
Adjust limit values to the new approach. Min and max in limit means the
values that are valid, so decrease max and num_static by one.
Set vsi::irq_dyn_alloc if dynamic allocation is supported.
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d9e9f6d7b7 ]
Attempts to replace an MDB group membership of the host itself are
currently bounced:
# ip link add name br up type bridge vlan_filtering 1
# bridge mdb replace dev br port br grp 239.0.0.1 vid 2
# bridge mdb replace dev br port br grp 239.0.0.1 vid 2
Error: bridge: Group is already joined by host.
A similar operation done on a member port would succeed. Ignore the check
for replacement of host group memberships as well.
The bit of code that this enables is br_multicast_host_join(), which, for
already-joined groups only refreshes the MC group expiration timer, which
is desirable; and a userspace notification, also desirable.
Change a selftest that exercises this code path from expecting a rejection
to expecting a pass. The rest of MDB selftests pass without modification.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://patch.msgid.link/e5c5188b9787ae806609e7ca3aa2a0a501b9b5c4.1738685648.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 50f37fc2a3 ]
if CONFIG_NET_IPGRE is enabled, but CONFIG_IPV6 is disabled:
net/ipv4/ip_gre.c: In function ‘ipgre_err’:
net/ipv4/ip_gre.c:144:22: error: variable ‘data_len’ set but not used [-Werror=unused-but-set-variable]
144 | unsigned int data_len = 0;
| ^~~~~~~~
Fix this by moving all data_len processing inside the IPV6-only section
that uses its result.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202501121007.2GofXmh5-lkp@intel.com/
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/d09113cfe2bfaca02f3dddf832fb5f48dd20958b.1738704881.git.geert@linux-m68k.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f6205f8215 ]
The 'used' and 'updated' fields in the FDB entry structure can be
accessed concurrently by multiple threads, leading to reports such as
[1]. Can be reproduced using [2].
Suppress these reports by annotating these accesses using
READ_ONCE() / WRITE_ONCE().
[1]
BUG: KCSAN: data-race in vxlan_xmit / vxlan_xmit
write to 0xffff942604d263a8 of 8 bytes by task 286 on cpu 0:
vxlan_xmit+0xb29/0x2380
dev_hard_start_xmit+0x84/0x2f0
__dev_queue_xmit+0x45a/0x1650
packet_xmit+0x100/0x150
packet_sendmsg+0x2114/0x2ac0
__sys_sendto+0x318/0x330
__x64_sys_sendto+0x76/0x90
x64_sys_call+0x14e8/0x1c00
do_syscall_64+0x9e/0x1a0
entry_SYSCALL_64_after_hwframe+0x77/0x7f
read to 0xffff942604d263a8 of 8 bytes by task 287 on cpu 2:
vxlan_xmit+0xadf/0x2380
dev_hard_start_xmit+0x84/0x2f0
__dev_queue_xmit+0x45a/0x1650
packet_xmit+0x100/0x150
packet_sendmsg+0x2114/0x2ac0
__sys_sendto+0x318/0x330
__x64_sys_sendto+0x76/0x90
x64_sys_call+0x14e8/0x1c00
do_syscall_64+0x9e/0x1a0
entry_SYSCALL_64_after_hwframe+0x77/0x7f
value changed: 0x00000000fffbac6e -> 0x00000000fffbac6f
Reported by Kernel Concurrency Sanitizer on:
CPU: 2 UID: 0 PID: 287 Comm: mausezahn Not tainted 6.13.0-rc7-01544-gb4b270f11a02 #5
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.3-3.fc41 04/01/2014
[2]
#!/bin/bash
set +H
echo whitelist > /sys/kernel/debug/kcsan
echo !vxlan_xmit > /sys/kernel/debug/kcsan
ip link add name vx0 up type vxlan id 10010 dstport 4789 local 192.0.2.1
bridge fdb add 00:11:22:33:44:55 dev vx0 self static dst 198.51.100.1
taskset -c 0 mausezahn vx0 -a own -b 00:11:22:33:44:55 -c 0 -q &
taskset -c 2 mausezahn vx0 -a own -b 00:11:22:33:44:55 -c 0 -q &
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://patch.msgid.link/20250204145549.1216254-2-idosch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 689805dcc4 ]
When attempting to enable MQPRIO while HTB offload is already
configured, the driver currently returns `-EINVAL` and triggers a
`WARN_ON`, leading to an unnecessary call trace.
Update the code to handle this case more gracefully by returning
`-EOPNOTSUPP` instead, while also providing a helpful user message.
Signed-off-by: Carolina Jubran <cjubran@nvidia.com>
Reviewed-by: Yael Chemla <ychemla@nvidia.com>
Reviewed-by: Cosmin Ratiu <cratiu@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2f1361f862 ]
There is no CSID TPG on some SoCs, so the v4l2 ctrl in CSID driver
shouldn't be registered. Checking the supported TPG modes to indicate
if the TPG hardware exists or not and only registering v4l2 ctrl for
CSID only when the TPG hardware is present.
Signed-off-by: Depeng Shao <quic_depengs@quicinc.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 21925ede44 ]
In /sys/fs/f2fs/features, there's no f2fs_sb_info, so let's avoid to get
the pointer.
Reviewed-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8df0f00282 ]
The expression PCC_NUM_RETRIES * pcc_chan->latency is currently being
evaluated using 32-bit arithmetic.
Since a value of type 'u64' is used to store the eventual result,
and this result is later sent to the function usecs_to_jiffies with
input parameter unsigned int, the current data type is too wide to
store the value of ctx->usecs_lat.
Change the data type of "usecs_lat" to a more suitable (narrower) type.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Signed-off-by: Andrey Vatoropin <a.vatoropin@crpt.ru>
Link: https://lore.kernel.org/r/20250204095400.95013-1-a.vatoropin@crpt.ru
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 52b10b591f ]
Update some RCGs on the sm8250 camera clock controller to use
clk_rcg2_shared_ops. The shared_ops ensure the RCGs get parked
to the XO during clock disable to prevent the clocks from locking up
when the GDSC is enabled. These mirror similar fixes for other controllers
such as commit e5c359f70e ("clk: qcom: camcc: Update the clock ops for
the SC7180").
Signed-off-by: Jordan Crouse <jorcrous@amazon.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Link: https://lore.kernel.org/r/20250122222612.32351-1-jorcrous@amazon.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8425f5c8f0 ]
Don't call ltecoex_read_reg() and ltecoex_reg_write() when the
ltecoex_addr member of struct rtw_chip_info is NULL. The RTL8814AU
doesn't have this feature.
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/55b5641f-094e-4f94-9f79-ac053733f2cf@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9e8243025c ]
After the firmware is uploaded, download_firmware_validate() checks some
bits in REG_MCUFW_CTRL to see if everything went okay. The
RTL8814AU power on sequence sets bits 13 and 12 to 2, which this
function does not expect, so it thinks the firmware upload failed.
Make download_firmware_validate() ignore bits 13 and 12.
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/049d2887-22fc-47b7-9e59-62627cb525f8@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 17207d0bb2 ]
When zeroing a range of folios on the filesystem which block size is
less than the page size, the file's mapped blocks within one page will
be marked as unwritten, we should remove writable userspace mappings to
ensure that ext4_page_mkwrite() can be called during subsequent write
access to these partial folios. Otherwise, data written by subsequent
mmap writes may not be saved to disk.
$mkfs.ext4 -b 1024 /dev/vdb
$mount /dev/vdb /mnt
$xfs_io -t -f -c "pwrite -S 0x58 0 4096" -c "mmap -rw 0 4096" \
-c "mwrite -S 0x5a 2048 2048" -c "fzero 2048 2048" \
-c "mwrite -S 0x59 2048 2048" -c "close" /mnt/foo
$od -Ax -t x1z /mnt/foo
000000 58 58 58 58 58 58 58 58 58 58 58 58 58 58 58 58
*
000800 59 59 59 59 59 59 59 59 59 59 59 59 59 59 59 59
*
001000
$umount /mnt && mount /dev/vdb /mnt
$od -Ax -t x1z /mnt/foo
000000 58 58 58 58 58 58 58 58 58 58 58 58 58 58 58 58
*
000800 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
*
001000
Fix this by introducing ext4_truncate_page_cache_block_range() to remove
writable userspace mappings when truncating a partial folio range.
Additionally, move the journal data mode-specific handlers and
truncate_pagecache_range() into this function, allowing it to serve as a
common helper that correctly manages the page cache in preparation for
block range manipulations.
Signed-off-by: Zhang Yi <yi.zhang@huawei.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Ojaswin Mujoo <ojaswin@linux.ibm.com>
Link: https://patch.msgid.link/20241220011637.1157197-2-yi.zhang@huaweicloud.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 43d0105e2c ]
There is no need to write back all data before punching a hole in
non-journaled mode since it will be dropped soon after removing space.
Therefore, the call to filemap_write_and_wait_range() can be eliminated.
Besides, similar to ext4_zero_range(), we must address the case of
partially punched folios when block size < page size. It is essential to
remove writable userspace mappings to ensure that the folio can be
faulted again during subsequent mmap write access.
In journaled mode, we need to write dirty pages out before discarding
page cache in case of crash before committing the freeing data
transaction, which could expose old, stale data, even if synchronization
has been performed.
Signed-off-by: Zhang Yi <yi.zhang@huawei.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Ojaswin Mujoo <ojaswin@linux.ibm.com>
Link: https://patch.msgid.link/20241220011637.1157197-4-yi.zhang@huaweicloud.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Sasha Levin <sashal@kernel.org>
