Following a hard reset of a SAS raid, one of the raid targets is occasionally
missing. I tracked this down to a pretty obscure little bug.
The LSI fusion drivers for SAS and Fibre Channel both use their respective
transport layers. Those transport layers increment the target number
assigned to new targets.
The routine __scsi_scan_target uses the "this_id" element of the Scsi_Host
structure to avoid scanning the scsi host adapter. Both fusion drivers set
"this_id" from a value returned in a firmware PortFacts response. For my
particular test case (SAS) the firmware id assigned to the initiator was
173. After enough raid resets to cause the raid targets to go and come a
sufficient number of times, the id assigned by the transport to a raid
target would match the id assigned by the host adapter to the "this_id"
field, resulting in that target not being scanned.
Fix by not assigning this_id and not checking it in slave_configure.
Signed-off-by: Michael Reed <mdr@sgi.com>
Acked-by: "Moore, Eric" <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Clean up the advantech watchdog code and inspect for BKL problems
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
There's a reason why using C99 initialisers even in the supposedly
trivial structs is a good idea.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fixed EAPD and COEF setups for Realtek ALC662/663, 660-VD and 888 codecs.
Signed-off-by: Kailang Yang <kailang@realtek.com.tw>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Show more exact codec chip name in the PCM stream name strings.
Signed-off-by: Kailang Yang <kailang@realtek.com.tw>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added the support of ALC663 codec, including specific models for
ASUS M51VA, ASUS G71V, ASUS H13 and ASUS G50V.
Signed-off-by: Kailang Yang <kailang@realtek.com.tw>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added the missing PCI ID for ICH9 controller (8086:2911)
Signed-off-by: Kailang Yang <kailang@realtek.com.tw>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Replace CONFIG_SND_DEBUG_DETECT with CONFIG_SND_DEBUG_VERBOSE to
represent its meaning more better. This config isn't provided only
for the detection but for more verbose debug prints in general.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The kconfig items related with AC97-powersave must be outside the
CONFIG_SND_PCI range. And it'd be better together with CONFIG_SND_AC97.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch removes CVS keywords that weren't updated for a long time
from comments.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch removes CVS keywords that weren't updated for a long time
from comments.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added entry into usbquirks.h to recognize Roland SonicCell sound module by
mostly duplicating the entry for the Roland SH-201. USB MIDI works just fine,
though the USB audio is a little unreliable (but still works well enough).
Signed-off-by: Chris Mennie <camennie@alumni.uwaterloo.ca>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The identification of this bug is thanks to Cheng Wei and Tomasz
Grobelny.
To avoid divide-by-zero, the implementation previously ignored RTTs
smaller than 4 microseconds when performing integer division RTT/4.
When the RTT reached a value less than 4 microseconds (as observed on
loopback), this prevented the Window Counter CCVal value from
advancing. As a result, the receiver stopped sending feedback. This in
turn caused non-ending expiries of the nofeedback timer at the sender,
so that the sending rate was progressively reduced until reaching the
minimum of one packet per 64 seconds.
The patch fixes this bug by handling integer division more
intelligently. Due to consistent use of dccp_sample_rtt(),
divide-by-zero-RTT is avoided.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
RFC4340 said:
8.5. Pseudocode
...
If P.type is not Data, Ack, or DataAck and P.X == 0 (the packet
has short sequence numbers), drop packet and return
But DCCP has some mistake to handle short sequence numbers packet, now
it drop packet only if P.type is Data, Ack, or DataAck and P.X == 0.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Acked-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
remove extra -1 in reseve_early calling
panic if can not find space for new RAMDISK
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Hook into the device model to make sure that timekeeping's resume handler
is called. This deals with our clocksource's non-monotonicity over the
save/restore. Explicitly call clock_has_changed() to make sure that
all the timers get retriggered properly.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch implements Xen save/restore and migration.
Saving is triggered via xenbus, which is polled in
drivers/xen/manage.c. When a suspend request comes in, the kernel
prepares itself for saving by:
1 - Freeze all processes. This is primarily to prevent any
partially-completed pagetable updates from confusing the suspend
process. If CONFIG_PREEMPT isn't defined, then this isn't necessary.
2 - Suspend xenbus and other devices
3 - Stop_machine, to make sure all the other vcpus are quiescent. The
Xen tools require the domain to run its save off vcpu0.
4 - Within the stop_machine state, it pins any unpinned pgds (under
construction or destruction), performs canonicalizes various other
pieces of state (mostly converting mfns to pfns), and finally
5 - Suspend the domain
Restore reverses the steps used to save the domain, ending when all
the frozen processes are thawed.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
When restoring, rebind the existing xenbus irq to the new xenbus event
channel. (It turns out in practice that this is always the same, and
is never updated on restore. That's a bug, but Xeno-linux has been
like this for a long time, so it can't really be fixed.)
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Add code to:
1. Deal with the console page being canonicalized. During save, the
console's mfn in the start_info structure is canonicalized to a pfn.
In order to deal with that, we always use a copy of the pfn and
indirect off that all the time. However, we fall back to using the
mfn if the pfn hasn't been initialized yet.
2. Restore the console event channel, and rebind it to the existing irq.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Rearrange the tests in unbind_from_irq() so that we can still unbind
an irq even if the underlying event channel is bad. This allows a
device driver to shuffle its irqs on save/restore before the
underlying event channels have been fixed up.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Add rebind_evtchn_irq(), which will rebind an device driver's existing
irq to a new event channel on restore. Since the new event channel
will be masked and bound to vcpu0, we update the state accordingly and
unmask the irq once everything is set up.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
When saving a domain, the Xen tools need to remap all our mfns to
portable pfns. In order to remap our p2m table, it needs to know
where all its pages are, so maintain the references to the p2m table
for it to use.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Rename dummy_shared_info to xen_dummy_shared_info and make it
non-static, in anticipation of users outside of enlighten.c
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
When using sparsemem and memory hotplug, the kernel's pseudo-physical
address space can be discontigious. Previously this was dealt with by
having the upper parts of the radix tree stubbed off. Unfortunately,
this is incompatible with save/restore, which requires a complete p2m
table.
The solution is to have a special distinguished all-invalid p2m leaf
page, which we can point all the hole areas at. This allows the tools
to see a complete p2m table, but it only costs a page for all memory
holes.
It also simplifies the code since it removes a few special cases.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Add a config option to set the max size of a Xen domain. This is used
to scale the size of the physical-to-machine array; it ends up using
around 1 page/GByte, so there's no reason to be very restrictive.
For a 32-bit guest, the default value of 8GB is probably sufficient;
there's not much point in giving a 32-bit machine much more memory
than that.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
We now support the use of memory hotplug, so the physical to machine
page mapping structure must be dynamic. This is implemented as a
two-level radix tree structure, which allows us to efficiently
incrementally allocate memory for the p2m table as new pages are
added.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Make the needlessly global balloon_set_new_target() static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Make sure resched interrupts appear in /proc/interrupts in the proper
place.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Add xen handles realted definitions for xen memory which ia64/xen needs.
Pointer argumsnts for ia64/xen hypercall are passed in pseudo physical
address (guest physical address) so that it is required to convert
guest kernel virtual address into pseudo physical address.
The xen guest handle represents such arguments.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
fix compilation error of ballon driver on ia64.
extent_start member is pointer argument. On x86 pointer argument for
xen hypercall is passed as virtual address.
On the other hand, ia64 and ppc, pointer argument is passed in pseudo
physical address. (guest physicall address.)
So they must be passed as handle and convert right before issuing hypercall.
CC drivers/xen/balloon.o
linux-2.6-x86/drivers/xen/balloon.c: In function 'increase_reservation':
linux-2.6-x86/drivers/xen/balloon.c:228: error: incompatible types in assignment
linux-2.6-x86/drivers/xen/balloon.c: In function 'decrease_reservation':
linux-2.6-x86/drivers/xen/balloon.c:324: error: incompatible types in assignment
linux-2.6-x86/drivers/xen/balloon.c: In function 'dealloc_pte_fn':
linux-2.6-x86/drivers/xen/balloon.c:486: error: incompatible types in assignment
linux-2.6-x86/drivers/xen/balloon.c: In function 'alloc_empty_pages_and_pagevec':
linux-2.6-x86/drivers/xen/balloon.c:522: error: incompatible types in assignment
make[2]: *** [drivers/xen/balloon.o] Error 1
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
move arch/x86/xen/manage.c under drivers/xen/to share codes
with x86 and ia64.
ia64/xen also uses manage.c
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
For some perverse reason, if you call add_preferred_console() it prevents
setup_early_printk() from successfully enabling the boot console -
unless you make it a preferred console too...
Also, make xenboot console output distinct from normal console output,
since it gets repeated when the console handover happens, and the
duplicated output is confusing without disambiguation.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Markus Armbruster <armbru@redhat.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
The pvfb backend indicates dynamic mode support by creating node
feature_resize with a non-zero value in its xenstore directory.
xen-fbfront sends a resize notification event on mode change. Fully
backwards compatible both ways.
Framebuffer size and initial resolution can be controlled through
kernel parameter xen_fbfront.video. The backend enforces a separate
size limit, which it advertises in node videoram in its xenstore
directory.
xen-kbdfront gets the maximum screen resolution from nodes width and
height in the backend's xenstore directory instead of hardcoding it.
Additional goodie: support for larger framebuffers (512M on a 64-bit
system with 4K pages).
Changing the number of bits per pixels dynamically is not supported,
yet.
Ported from
http://xenbits.xensource.com/linux-2.6.18-xen.hg?rev/92f7b3144f41http://xenbits.xensource.com/linux-2.6.18-xen.hg?rev/bfc040135633
Signed-off-by: Pat Campbell <plc@novell.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This isn't a security flaw (the backend can see all our memory
anyway). But it's the right thing to do all the same.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
These are mostly for completeness and consistency with the other
frontends, as PVFB is typically compiled in rather than a module.
Derived from
http://xenbits.xensource.com/linux-2.6.18-xen.hg?rev/5e294e29a43e
While there, add module descriptions.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
