Without console= arguments on the kernel command line, the first
console to register becomes enabled and the preferred console (the one
behind /dev/console). This is normally tty (assuming
CONFIG_VT_CONSOLE is enabled, which it commonly is).
This is okay as long tty is a useful console. But unless we have the
PV framebuffer, and it is enabled for this domain, tty0 in domU is
merely a dummy. In that case, we want the preferred console to be the
Xen console hvc0, and we want it without having to fiddle with the
kernel command line. Commit b8c2d3dfbc
did that for us.
Since we now have the PV framebuffer, we want to enable and prefer tty
again, but only when PVFB is enabled. But even then we still want to
enable the Xen console as well.
Problem: when tty registers, we can't yet know whether the PVFB is
enabled. By the time we can know (xenstore is up), the console setup
game is over.
Solution: enable console tty by default, but keep hvc as the preferred
console. Change the preferred console to tty when PVFB probes
successfully, unless we've been given console kernel parameters.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Add pte_flags() to extract the flags from a pte. This is a special
case of pte_val() which is only guaranteed to return the pte's flags
correctly; the page number may be corrupted or missing.
The intent is to allow paravirt implementations to return pte flags
without having to do any translation of the page number (most notably,
Xen).
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
When enabling interrupts, we don't need to worry about preemption,
because we either enter with interrupts disabled - so no preemption -
or the caller is confused and is re-enabling interrupts on some
indeterminate processor.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The guest can legitimately change things like cr4.OSFXSR and
OSXMMEXCPT, so let it.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Use the new sched_op hypercall, mainly because xenner doesn't support
the old one.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Xen will trap and emulate clts, but its better to use a hypercall.
Also, xenner doesn't handle clts.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
When using "earlyprintk=xen", also write the console output to the raw
debug console. This will appear on dom0's console if the hypervisor
has been compiled to allow it.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Add a couple of functions which can write directly to the Xen console
for debugging. This output ends up on the host's dom0 console
(assuming it allows the domain to write there).
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Rather than making _PAGE_* constants signed, and then relying on
sign-extension to make sure that masks derived from them are wide
enough, just explicitly type them pteval_t. This guarantees that they
and any derived values are the right size for the current pte format.
The reliance on sign extension is fragile, and invokes some very
subtle corners of the C type system.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Move the AP7 cpufreq init to late_initcall() so that we don't try to
bring up cpufreq until the governor is ready. x86 also uses
late_initcall() for this.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
The chip phy_init() function must be called before the dig_enable() function
but dig_enable() is called when the device is opened and we only call
phy_init() after having reigstered the device, meaning the two can race.
Fix this by doing the phy_init() before we register the input device.
Thanks to Rodolfo Giometti <giometti@enneenne.com> for the report.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Fix driver name - thanks to Guennadi Liakhovetski <g.liakhovetski@gmx.de> for
reporting this.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
phys is displayed in diagnostic output like that from evbug so ensure
that it is set to something.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Also do not fail i8042 entire initialization if enabling dritek extension
fails.
Signed-off-by: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Add Chien and remove Nishi from maintainers list for NetEffect.
Signed-off-by: Chien Tung <ctung@neteffect.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The driver supports a few features (RNR NAK, port active event, SRQ
resize) that were not reported in the device capability flags. This
patch fixes that.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Gabriel C <nix.or.die@googlemail.com> pointed out that when the x86
bitops are updated to operate on unsigned long, the code in
sdma_abort_task() will produce warnings:
drivers/infiniband/hw/ipath/ipath_sdma.c: In function 'sdma_abort_task':
drivers/infiniband/hw/ipath/ipath_sdma.c:267: warning: passing argument 2 of 'constant_test_bit' from incompatible pointer type
and so on, because it uses test_bit() to operation on a u64 value
(returned by ipath_read_kref64() for a hardware register).
Fix up these warnings by converting the test_bit() operations to &ing
with appropriate symbolic defines of the bits within the hardware
register. This has the benign side-effect of making the code more
self-documenting as well.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The variables dns and inc are not used, remove them.
Signed-off-by: Carlos R. Mafra <crmafra@gmail.com>
Cc: tglx@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
hres_timers_resume() warns if there appears to be more than one cpu
online. This warning makes sense when the suspend/resume mechanism
offlines all cpus but one during the suspend/resume process.
However, Xen suspend does not need to offline the other cpus; it
merely keeps them tied up in stop_machine() while the virtual machine
is suspended. The warning hres_timers_resume issues is therefore
spurious.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: xen-devel <xen-devel@lists.xensource.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Hi Ingo/Steven,
Ftrace currently maintains an update count which includes false updates,
i.e, updates which failed. If anything, such failures should be tracked
by some separate variable, but this patch provides a minimal fix.
Signed-off-by: Abhishek Sagar <sagar.abhishek@gmail.com>
Cc: rostedt@goodmis.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Hi Steven,
I noticed that concurrent instances of ftrace_record_ip()
have a race between ftrace_hash list traversal during
ftrace_ip_in_hash() (before acquiring ftrace_shutdown_lock)
and ftrace_add_hash(). If it's so then this should fix it.
Signed-off-by: Abhishek Sagar <sagar.abhishek@gmail.com>
Cc: rostedt@goodmis.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch cleans up the ftrace code in PowerPC based on the comments from
Michael Ellerman.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Cc: Michael Ellerman <michael@ellerman.id.au>
Cc: proski@gnu.org
Cc: a.p.zijlstra@chello.nl
Cc: Pekka Paalanen <pq@iki.fi>
Cc: Steven Rostedt <srostedt@redhat.com>
Cc: linuxppc-dev@ozlabs.org
Cc: Soeren Sandmann Pedersen <sandmann@redhat.com>
Cc: paulus@samba.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The new work with converting the trace hooks over to markers broke the
command line recording of ftrace. This patch fixes it again.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
While debugging latencies in the RT kernel, I found that it would be nice
to be able to filter away functions from the trace than just to filter
on functions.
I added a new interface to the debugfs tracing directory called
set_ftrace_notrace
When dynamic frace is enabled, this lets you filter away functions that will
not be recorded in the trace. It is similar to adding 'notrace' to those
functions but by doing it without recompiling the kernel.
Here's how set_ftrace_filter and set_ftrace_notrace interact. Remember, if
set_ftrace_filter is set, it removes all functions from the trace execpt for
those listed in the set_ftrace_filter. set_ftrace_notrace will prevent those
functions from being traced.
If you were to set one function in both set_ftrace_filter and
set_ftrace_notrace and that function was the same, then you would end up
with an empty trace.
the set of functions to trace is:
set_ftrace_filter == empty then
all functions not in set_ftrace_notrace
else
set of the set_ftrace_filter and not in set of set_ftrace_notrace.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Printing out new max latencies was fine for the old RT tracer. But for
mainline it is a bit messy. We also need to test if the run queue
is locked before we can do the print. This means that we may not be
printing out latencies if the run queue is locked on another CPU.
This produces inconsistencies in the output.
This patch simply removes the print altogether.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Cc: pq@iki.fi
Cc: proski@gnu.org
Cc: sandmann@redhat.com
Cc: a.p.zijlstra@chello.nl
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch adds function tracing to the functions that are called
on the CPU of the task being traced.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Cc: pq@iki.fi
Cc: proski@gnu.org
Cc: sandmann@redhat.com
Cc: a.p.zijlstra@chello.nl
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The check_pages function is called often enough that it can cause problems
with trace outputs or even bringing the system to a halt.
This patch limits the check_pages to the places that are most likely to
have problems. The check is made at the flip between the global array and
the max save array, as well as when the size of the buffers changes and
the self tests.
This patch also removes the BUG_ON from check_pages and replaces it with
a WARN_ON and disabling of the tracer.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Cc: pq@iki.fi
Cc: proski@gnu.org
Cc: sandmann@redhat.com
Cc: a.p.zijlstra@chello.nl
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
gcc 4.0 fails to allocate %eax for the pattern operand in the rep
store instructions used by memset; force it to do so by declaring a
register variable.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Based on Roland's patch. This approach was suggested by Austin Clements
from the very beginning, and then by Linus.
As Austin pointed out, the execing task can be killed by SI_TIMER signal
because exec flushes the signal handlers, but doesn't discard the pending
signals generated by posix timers. Perhaps not a bug, but people find this
surprising. See http://bugzilla.kernel.org/show_bug.cgi?id=10460
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Austin Clements <amdragon+kernelbugzilla@mit.edu>
Cc: Roland McGrath <roland@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently sigqueue_free() removes sigqueue from list, but doesn't cancel the
pending signal. This is not consistent, the task should either receive the
"full" signal along with siginfo_t, or it shouldn't receive the signal at all.
Change sigqueue_free() to clear SIGQUEUE_PREALLOC but leave sigqueue on list
if it is queued.
This is a user-visible change. If the signal is blocked, it stays queued
after sys_timer_delete() until unblocked with the "stale" si_code/si_value,
and of course it is still counted wrt RLIMIT_SIGPENDING which also limits
the number of posix timers.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Austin Clements <amdragon+kernelbugzilla@mit.edu>
Cc: Roland McGrath <roland@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6.26:
sh: Drop broken URAM support on SH7723.
sh: update Migo-R defconfig
sh: use sm501 8250 mfd support on r2d boards
sh: add probe support for new sh7723 cut
sh: fix VPU interrupt vector for sh7723
sh: fix USBF resource for sh7722
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (52 commits)
vlan: Use bitmask of feature flags instead of seperate feature bits
fmvj18x_cs: add NextCom NC5310 rev B support
xirc2ps_cs: re-initialize the multicast address in do_reset
3C509: rx_bytes should not be increased when alloc_skb failed
NETFRONT: Use __skb_queue_purge()
VIRTIO: Use __skb_queue_purge()
phylib: do EXPORT_SYMBOL on get_phy_id
netlink: Fix nla_parse_nested_compat() to call nla_parse() directly
WAN: protect HDLC proto list while insmod/rmmod
drivers/net/fs_enet: remove null pointer dereference
S2io: Version update for napi and MSI-X patches
S2io: Added napi support when MSIX is enabled.
S2io: Move all the transmit completions to a single msi-x (alarm) vector
drivers/net/ehea - remove unnecessary memset after kzalloc
au1000_eth: remove useless check
Blackfin EMAC Driver: Removed duplicated include <linux/ethtool.h>
cpmac bugfixes and enhancements
e1000e: use resource_size_t, not unsigned long, for phys addrs
net/usb: add support for Apple USB Ethernet Adapter
uli526x: add support for netpoll
...
I can't think of any valid reason for ext4 to not use barriers when
they are available; I believe this is necessary for filesystem
integrity in the face of a volatile write cache on storage.
An administrator who trusts that the cache is sufficiently battery-
backed (and power supplies are sufficiently redundant, etc...)
can always turn it back off again.
SuSE has carried such a patch for ext3 for quite some time now.
Also document the mount option while we're at it.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: Mingming Cao <cmm@us.ibm.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
If the device doesn't support write barriers, the write is retried
without ordered mode. But the buffer head needs to be re-locked or
submit_bh will fail with on BUG(!buffer_locked(bh)).
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
If a journal checksum error is detected, the ext4 filesystem will call
ext4_error(), and the mount will either continue, become a read-only
mount, or cause a kernel panic based on the superblock flags
indicating the user's preference of what to do in case of filesystem
corruption being detected.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
There is a bug when we are trying to verify that the reserve inode's
double indirect blocks point back to the primary gdt blocks. The fix is
obvious, we need to mod the gdb count by the addr's per block. This was
verified using the same testcase as with the ext3 equivalent of this
patch.
Signed-off-by: Josef Bacik <jbacik@redhat.com>
Signed-off-by: Mingming Cao <cmm@us.ibm.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
With FLEX_BG block bitmaps, inode bitmaps and inode tables _MAY_ be
allocated outside the group. So, when initializing an uninitialized
block bitmap, we need to check the location of this blocks before
setting the corresponding bits in the block bitmap of the newly
initialized group. Also return the right number of free blocks when
counting the available free blocks in uninit group.
Tested-by: Aneesh Kumar K.V <aneesh.kumar@inux.vnet.ibm.com>
Signed-off-by: Jose R. Santos <jrs@us.ibm.com>
Signed-off-by: Mingming Cao <cmm@us.ibm.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Fix use of uninitialized data with debug enabled.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Mingming Cao <cmm@us.ibm.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
(Updated with a common max-stack-used checker that knows about
the canary, as suggested by Joe Perches)
Use a canary at the end of the stack to clearly indicate
at oops time whether the stack has ever overflowed.
This is a very simple implementation with a couple of
drawbacks:
1) a thread may legitimately use exactly up to the last
word on the stack
-- but the chances of doing this and then oopsing later seem slim
2) it's possible that the stack usage isn't dense enough
that the canary location could get skipped over
-- but the worst that happens is that we don't flag the overrun
-- though this happens fairly often in my testing :(
With the code in place, an intentionally-bloated stack oops might
do:
BUG: unable to handle kernel paging request at ffff8103f84cc680
IP: [<ffffffff810253df>] update_curr+0x9a/0xa8
PGD 8063 PUD 0
Thread overran stack or stack corrupted
Oops: 0000 [1] SMP
CPU 0
...
... unless the stack overrun is so bad that it corrupts some other
thread.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
If the user selects the stack-protector config option, but does not have
a gcc that has the right bits enabled (for example because it isn't build
with a glibc that supports TLS, as is common for cross-compilers, but also
because it may be too old), then the runtime test fails right now.
This patch adds a warning message for this scenario. This warning accomplishes
two goals
1) the user is informed that the security option he selective isn't available
2) the user is suggested to turn of the CONFIG option that won't work for him,
and would make the runtime test fail anyway.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
