Currently dax_pmd_fault() decides to fill a PMD-sized hole only if
returned buffer has BH_Uptodate set. However that doesn't get set for
any mapping buffer so that branch is actually a dead code. The
BH_Uptodate check doesn't make any sense so just remove it.
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
The critical clock handling in __clk_core_init isn't taking the enable lock
before calling clk_core_enable, which in turns triggers the warning in the
lockdep_assert_held call in that function when lockep is enabled.
Add the calls to clk_enable_lock/unlock to make sure it doesn't happen.
Fixes: 32b9b10961 ("clk: Allow clocks to be marked as CRITICAL")
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
PCI-Express spec says that reading 4 bytes at offset 100h should return
zero if there is no extended capability so VFIO reads this dword to
know if there are extended capabilities.
However it is not always possible to access the extended space so
generic PCI code in pci_cfg_space_size_ext() checks if
pci_read_config_dword() can read beyond 100h and if the check fails,
it sets the config space size to 100h.
VFIO does its own extended capabilities check by reading at offset 100h
which may produce 0xffffffff which VFIO treats as the extended config
space presense and calls vfio_ecap_init() which fails to parse
capabilities (which is expected) but right before the exit, it writes
zero at offset 100h which is beyond the buffer allocated for
vdev->vconfig (which is 256 bytes) which leads to random memory
corruption.
This makes VFIO only check for the extended capabilities if
the discovered config size is more than 256 bytes.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
This time was again a relatively calm development cycle; most of
updates are about drivers, and no radical changes are seen in any
core code. Here are some highlights:
ALSA core:
- Continued hardening of ALSA hrtimer
- A few leak fixes in timer interface
- Fix poll error handling in PCM and compress
- Add error propagation in compress API
- Removal of dead rtctimer driver
HD-audio:
- Native ELD notify support for i915 HDMI
- Realtek ALC234 & co support
- Code refactoring to standardize chmap support
- Continued development for SKL HDMI core support
Firewire:
- Apply delayed card registration to all drivers
- Improved / stabilized the handling of PCM stream start / stop
- Add tracepoints to dump a part of isochronous packet data
- Fixed incoming/outgoing packet parameter usages
- Add support for M-Audio profire series
USB-audio:
- Fixes for UAC2 clock source
- SS+ support
- Workaround for oft-seen repeated sample rate read errors
ASoC:
- Further slow progress on the topology code
- Substantial updates and improvements for the da7219, es8328,
fsl-ssi, Intel and rcar drivers.
- Compress error handling in WM ADSP driver
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=QsAc
-----END PGP SIGNATURE-----
Merge tag 'sound-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"This time was again a relatively calm development cycle; most of
updates are about drivers, and no radical changes are seen in any core
code. Here are some highlights:
ALSA core:
- Continued hardening of ALSA hrtimer
- A few leak fixes in timer interface
- Fix poll error handling in PCM and compress
- Add error propagation in compress API
- Removal of dead rtctimer driver
HD-audio:
- Native ELD notify support for i915 HDMI
- Realtek ALC234 & co support
- Code refactoring to standardize chmap support
- Continued development for SKL HDMI core support
Firewire:
- Apply delayed card registration to all drivers
- Improved / stabilized the handling of PCM stream start / stop
- Add tracepoints to dump a part of isochronous packet data
- Fixed incoming/outgoing packet parameter usages
- Add support for M-Audio profire series
USB-audio:
- Fixes for UAC2 clock source
- SS+ support
- Workaround for oft-seen repeated sample rate read errors
ASoC:
- Further slow progress on the topology code
- Substantial updates and improvements for the da7219, es8328,
fsl-ssi, Intel and rcar drivers.
- Compress error handling in WM ADSP driver"
* tag 'sound-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (177 commits)
ALSA: firewire-lib: change a member of event structure to suppress sparse wanings to bool type
sound: oss: Use setup_timer and mod_timer.
ASoC: hdac_hdmi: Remove the unused 'timeout' variable
ASoC: fsl_ssi: Fix channel slipping on capture (or playback) restart in full duplex.
ASoC: fsl_ssi: Fix channel slipping in Playback at startup
ASoC: fsl_ssi: Fix samples being dropped at Playback startup
ASoC: fsl_ssi: Save a dev reference for dev_err() purpose.
ASoC: fsl_ssi: The IPG/5 limitation concerns the bitclk, not the sysclk.
ASoC: fsl_ssi: Real hardware channels max number is 32
ASoC: pcm5102a: Add support for PCM5102A codec
ASoC: hdac_hdmi: add link management
ASoC: Intel: Skylake: add link management
ALSA: hdac: add link pm and ref counting
ALSA: au88x0: Fix zero clear of stream->resources
ASoC: rt298: Add DMI match for Broxton-P reference platform
ASoC: rt298: fix null deref on acpi driver data
ASoC: dapm: deprecate MICBIAS widget type
ALSA: firewire-lib: drop skip argument from helper functions to queue a packet
ALSA: firewire-lib: add context information to tracepoints
ALSA: firewire-lib: permit to flush queued packets only in process context for better PCM period granularity
...
Enumeration
Refine PCI support check in pcibios_init() (Adrian-Ken Rueegsegger)
Provide common functions for ECAM mapping (Jayachandran C)
Allow all PCIe services on non-ACPI host bridges (Jon Derrick)
Remove return values from pcie_port_platform_notify() and relatives (Jon Derrick)
Widen portdrv service type from 4 bits to 8 bits (Keith Busch)
Add Downstream Port Containment portdrv service type (Keith Busch)
Add Downstream Port Containment driver (Keith Busch)
Resource management
Identify Enhanced Allocation (EA) BAR Equivalent resources in sysfs (Alex Williamson)
Supply CPU physical address (not bus address) to iomem_is_exclusive() (Bjorn Helgaas)
alpha: Call iomem_is_exclusive() for IORESOURCE_MEM, but not IORESOURCE_IO (Bjorn Helgaas)
Mark Broadwell-EP Home Agent 1 as having non-compliant BARs (Prarit Bhargava)
Disable all BAR sizing for devices with non-compliant BARs (Prarit Bhargava)
Move PCI I/O space management from OF to PCI core code (Tomasz Nowicki)
PCI device hotplug
acpiphp_ibm: Avoid uninitialized variable reference (Dan Carpenter)
Use cached copy of PCI_EXP_SLTCAP_HPC bit (Lukas Wunner)
Virtualization
Mark Intel i40e NIC INTx masking as broken (Alex Williamson)
Reverse standard ACS vs device-specific ACS enabling (Alex Williamson)
Work around Intel Sunrise Point PCH incorrect ACS capability (Alex Williamson)
IOMMU
Add pci_add_dma_alias() to abstract implementation (Bjorn Helgaas)
Move informational printk to pci_add_dma_alias() (Bjorn Helgaas)
Add support for multiple DMA aliases (Jacek Lawrynowicz)
Add DMA alias quirk for mic_x200_dma (Jacek Lawrynowicz)
Thunderbolt
Fix double free of drom buffer (Andreas Noever)
Add Intel Thunderbolt device IDs (Lukas Wunner)
Fix typos and magic number (Lukas Wunner)
Support 1st gen Light Ridge controller (Lukas Wunner)
Generic host bridge driver
Use generic ECAM API (Jayachandran C)
Cavium ThunderX host bridge driver
Don't clobber read-only bits in bridge config registers (David Daney)
Use generic ECAM API (Jayachandran C)
Freescale i.MX6 host bridge driver
Use enum instead of bool for variant indicator (Andrey Smirnov)
Implement reset sequence for i.MX6+ (Andrey Smirnov)
Factor out ref clock enable (Bjorn Helgaas)
Add initial imx6sx support (Christoph Fritz)
Add reset-gpio-active-high boolean property to DT (Petr Štetiar)
Add DT property for link gen, default to Gen1 (Tim Harvey)
dts: Specify imx6qp version of PCIe core (Andrey Smirnov)
dts: Fix PCIe reset GPIO polarity on Toradex Apalis Ixora (Petr Štetiar)
Marvell Armada host bridge driver
add DT binding for Marvell Armada 7K/8K PCIe controller (Thomas Petazzoni)
Add driver for Marvell Armada 7K/8K PCIe controller (Thomas Petazzoni)
Marvell MVEBU host bridge driver
Constify mvebu_pcie_pm_ops structure (Jisheng Zhang)
Use SET_NOIRQ_SYSTEM_SLEEP_PM_OPS for mvebu_pcie_pm_ops (Jisheng Zhang)
Microsoft Hyper-V host bridge driver
Report resources release after stopping the bus (Vitaly Kuznetsov)
Add explicit barriers to config space access (Vitaly Kuznetsov)
Renesas R-Car host bridge driver
Select PCI_MSI_IRQ_DOMAIN (Arnd Bergmann)
Synopsys DesignWare host bridge driver
Remove incorrect RC memory base/limit configuration (Gabriele Paoloni)
Move Root Complex setup code to dw_pcie_setup_rc() (Jisheng Zhang)
TI Keystone host bridge driver
Add error IRQ handler (Murali Karicheri)
Remove unnecessary goto statement (Murali Karicheri)
Miscellaneous
Fix spelling errors (Colin Ian King)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=68Iz
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.7-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
"Enumeration:
- Refine PCI support check in pcibios_init() (Adrian-Ken Rueegsegger)
- Provide common functions for ECAM mapping (Jayachandran C)
- Allow all PCIe services on non-ACPI host bridges (Jon Derrick)
- Remove return values from pcie_port_platform_notify() and relatives (Jon Derrick)
- Widen portdrv service type from 4 bits to 8 bits (Keith Busch)
- Add Downstream Port Containment portdrv service type (Keith Busch)
- Add Downstream Port Containment driver (Keith Busch)
Resource management:
- Identify Enhanced Allocation (EA) BAR Equivalent resources in sysfs (Alex Williamson)
- Supply CPU physical address (not bus address) to iomem_is_exclusive() (Bjorn Helgaas)
- alpha: Call iomem_is_exclusive() for IORESOURCE_MEM, but not IORESOURCE_IO (Bjorn Helgaas)
- Mark Broadwell-EP Home Agent 1 as having non-compliant BARs (Prarit Bhargava)
- Disable all BAR sizing for devices with non-compliant BARs (Prarit Bhargava)
- Move PCI I/O space management from OF to PCI core code (Tomasz Nowicki)
PCI device hotplug:
- acpiphp_ibm: Avoid uninitialized variable reference (Dan Carpenter)
- Use cached copy of PCI_EXP_SLTCAP_HPC bit (Lukas Wunner)
Virtualization:
- Mark Intel i40e NIC INTx masking as broken (Alex Williamson)
- Reverse standard ACS vs device-specific ACS enabling (Alex Williamson)
- Work around Intel Sunrise Point PCH incorrect ACS capability (Alex Williamson)
IOMMU:
- Add pci_add_dma_alias() to abstract implementation (Bjorn Helgaas)
- Move informational printk to pci_add_dma_alias() (Bjorn Helgaas)
- Add support for multiple DMA aliases (Jacek Lawrynowicz)
- Add DMA alias quirk for mic_x200_dma (Jacek Lawrynowicz)
Thunderbolt:
- Fix double free of drom buffer (Andreas Noever)
- Add Intel Thunderbolt device IDs (Lukas Wunner)
- Fix typos and magic number (Lukas Wunner)
- Support 1st gen Light Ridge controller (Lukas Wunner)
Generic host bridge driver:
- Use generic ECAM API (Jayachandran C)
Cavium ThunderX host bridge driver:
- Don't clobber read-only bits in bridge config registers (David Daney)
- Use generic ECAM API (Jayachandran C)
Freescale i.MX6 host bridge driver:
- Use enum instead of bool for variant indicator (Andrey Smirnov)
- Implement reset sequence for i.MX6+ (Andrey Smirnov)
- Factor out ref clock enable (Bjorn Helgaas)
- Add initial imx6sx support (Christoph Fritz)
- Add reset-gpio-active-high boolean property to DT (Petr Štetiar)
- Add DT property for link gen, default to Gen1 (Tim Harvey)
- dts: Specify imx6qp version of PCIe core (Andrey Smirnov)
- dts: Fix PCIe reset GPIO polarity on Toradex Apalis Ixora (Petr Štetiar)
Marvell Armada host bridge driver:
- add DT binding for Marvell Armada 7K/8K PCIe controller (Thomas Petazzoni)
- Add driver for Marvell Armada 7K/8K PCIe controller (Thomas Petazzoni)
Marvell MVEBU host bridge driver:
- Constify mvebu_pcie_pm_ops structure (Jisheng Zhang)
- Use SET_NOIRQ_SYSTEM_SLEEP_PM_OPS for mvebu_pcie_pm_ops (Jisheng Zhang)
Microsoft Hyper-V host bridge driver:
- Report resources release after stopping the bus (Vitaly Kuznetsov)
- Add explicit barriers to config space access (Vitaly Kuznetsov)
Renesas R-Car host bridge driver:
- Select PCI_MSI_IRQ_DOMAIN (Arnd Bergmann)
Synopsys DesignWare host bridge driver:
- Remove incorrect RC memory base/limit configuration (Gabriele Paoloni)
- Move Root Complex setup code to dw_pcie_setup_rc() (Jisheng Zhang)
TI Keystone host bridge driver:
- Add error IRQ handler (Murali Karicheri)
- Remove unnecessary goto statement (Murali Karicheri)
Miscellaneous:
- Fix spelling errors (Colin Ian King)"
* tag 'pci-v4.7-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (48 commits)
PCI: Disable all BAR sizing for devices with non-compliant BARs
x86/PCI: Mark Broadwell-EP Home Agent 1 as having non-compliant BARs
PCI: Identify Enhanced Allocation (EA) BAR Equivalent resources in sysfs
PCI, of: Move PCI I/O space management to PCI core code
PCI: generic, thunder: Use generic ECAM API
PCI: Provide common functions for ECAM mapping
PCI: hv: Add explicit barriers to config space access
PCI: Use cached copy of PCI_EXP_SLTCAP_HPC bit
PCI: Add Downstream Port Containment driver
PCI: Add Downstream Port Containment portdrv service type
PCI: Widen portdrv service type from 4 bits to 8 bits
PCI: designware: Remove incorrect RC memory base/limit configuration
PCI: hv: Report resources release after stopping the bus
ARM: dts: imx6qp: Specify imx6qp version of PCIe core
PCI: imx6: Implement reset sequence for i.MX6+
PCI: imx6: Use enum instead of bool for variant indicator
PCI: thunder: Don't clobber read-only bits in bridge config registers
thunderbolt: Fix double free of drom buffer
PCI: rcar: Select PCI_MSI_IRQ_DOMAIN
PCI: armada: Add driver for Marvell Armada 7K/8K PCIe controller
...
Core changes:
- Add the devm_pinctrl_register() API and switch all applicable drivers
to use it, saving lots of lines of code all over the place.
New drivers:
- New driver for the Broadcom NS2 SoC.
- New subdriver for the PXA25x SoCs.
- New subdriver for the AMLogic Meson GXBB SoC.
Driver improvements:
- The Intel Baytrail driver now properly supports pin control.
- The Nomadik, Rockchip, Broadcom BCM2835 supports the .get_direction() callback in
the GPIO portions.
- Continued development and stabilization of several SH-PFC
SoC subdrivers: r8a7795, r8a7790, r8a7794 etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJXPZ9PAAoJEEEQszewGV1zboIQALtGX/tyKFzaOsj7WxHHjmfb
yufqU62NE0sPT6/hzUY3a1U9dpakbMehBXy0go0vcShmPSznX2glFv4GR6LEeE0+
o0JNv0d13f2s5WPEqn6L/ePuSuNNjfkwjZ7YJlAXx/WqAWI9c70H8/VHsXEObWOe
ZsAZx2FdUFDOxugDWsCmU6kt7RXbqTzEz2M/dDANr4B2cRH/3yny797P2y9tLy3w
Rqsdqw1C1A9SICSIRZ+YBWctXhRq5APsB75IncUYIQJF5hXoAcBCp6v+cNZHpXOw
X9J+zKDeMjOSsVvOyHA+4P+vPYgkOPl9GuUVJRvnbfCZYKEhDM1e5F393Cf7gYYz
dIEAzIFlPmZCMxog7AWEA0yDp2rJ2W/5WoN7pg+a5cKSHgriIry1sxDslBD2b9ZW
XxdVm4pMOiVw6yokHI4g2hcDsZOEW8zhPQi1wPuVuJ3k1m7T/d13mFAFTSWwOLVx
WFDLuD20ybkCVmxEs0ePrDzLcgEnxW40src6lqSzIx8bUBCH+iWPkIPH0fAJ6bNK
TFtfcCFrtE2YmpxrCgZceTLER/7jAGkXFegbJq1epNmz7+0wbEbRxcVFE1IbYUBW
ejslgTtLDvnzzkR7UISZF/Qna066tCGT52sEA82ZcrqytGkSTLB4kUDkQvXaCB0r
4DLJ47K32mQu3MrOPLjE
=tlvn
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v4.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This kernel cycle was quite calm when it comes to pin control and
there is really just one major change, and that is the introduction of
devm_pinctrl_register() managed resources.
Apart from that linear development, details below.
Core changes:
- Add the devm_pinctrl_register() API and switch all applicable
drivers to use it, saving lots of lines of code all over the place.
New drivers:
- driver for the Broadcom NS2 SoC
- subdriver for the PXA25x SoCs
- subdriver for the AMLogic Meson GXBB SoC
Driver improvements:
- the Intel Baytrail driver now properly supports pin control
- Nomadik, Rockchip, Broadcom BCM2835 support the .get_direction()
callback in the GPIO portions
- continued development and stabilization of several SH-PFC SoC
subdrivers: r8a7795, r8a7790, r8a7794 etc"
* tag 'pinctrl-v4.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (85 commits)
Revert "pinctrl: tegra: avoid parked_reg and parked_bank"
pinctrl: meson: Fix eth_tx_en bit index
pinctrl: tegra: avoid parked_reg and parked_bank
pinctrl: tegra: Correctly check the supported configuration
pinctrl: amlogic: Add support for Amlogic Meson GXBB SoC
pinctrl: rockchip: fix pull setting error for rk3399
pinctrl: stm32: Implement .pin_config_dbg_show()
pinctrl: nomadik: hide nmk_gpio_get_mode when unused
pinctrl: ns2: rename pinctrl_utils_dt_free_map
pinctrl: at91: Merge clk_prepare and clk_enable into clk_prepare_enable
pinctrl: at91: Make at91_gpio_template const
pinctrl: baytrail: fix some error handling in debugfs
pinctrl: ns2: add pinmux driver support for Broadcom NS2 SoC
pinctrl: sirf/atlas7: trivial fix of spelling mistake on flagged
pinctrl: sh-pfc: Kill unused variable in sh_pfc_remove()
pinctrl: nomadik: implement .get_direction()
pinctrl: nomadik: use BIT() with offsets consequently
pinctrl: exynos5440: Use off-stack memory for pinctrl_gpio_range
pinctrl: zynq: Use devm_pinctrl_register() for pinctrl registration
pinctrl: u300: Use devm_pinctrl_register() for pinctrl registration
...
May, we managed to uncover and fix some important bugs in our
new B.A.T.M.A.N. V algorithm. These are the fixes we came up with
together with others that I collected in the past weeks:
- avoid potential crash due to NULL pointer dereference in
B.A.T.M.A.N. V routine when a neigh_ifinfo object is not found, by
Sven Eckelmann
- avoid use-after-free of skb when counting outgoing bytes, by Florian
Westphal
- fix neigh_ifinfo object reference counting imbalance when using
B.A.T.M.A.N. V, by Sven Eckelmann. Such imbalance may lead to the
impossibility of releasing the related netdev object on shutdown
- avoid invalid memory access in case of error while allocating
bcast_own_sum when a new hard-interface is added, by Sven Eckelmann
- ensure originator address is updated in OMG/ELP packet content upon
primary interface address change, by Antonio Quartulli
- fix integer overflow when computing TQ metric (B.A.T.M.A.N. IV), by
Sven Eckelmann
- avoid race condition while adding new neigh_node which would result
in having two objects mapping to the same physical neighbour, by
Linus Lüssing
- ensure originator address is initialized in ELP packet content on
secondary interfaces, by Marek Lindner
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=IACg
-----END PGP SIGNATURE-----
Merge tag 'batman-adv-fix-for-davem' of git://git.open-mesh.org/linux-merge
Antonio Quartulli says:
====================
During the Wireless Battle Mesh v9 in Porto (PT) at the beginning of
May, we managed to uncover and fix some important bugs in our
new B.A.T.M.A.N. V algorithm. These are the fixes we came up with
together with others that I collected in the past weeks:
- avoid potential crash due to NULL pointer dereference in
B.A.T.M.A.N. V routine when a neigh_ifinfo object is not found, by
Sven Eckelmann
- avoid use-after-free of skb when counting outgoing bytes, by Florian
Westphal
- fix neigh_ifinfo object reference counting imbalance when using
B.A.T.M.A.N. V, by Sven Eckelmann. Such imbalance may lead to the
impossibility of releasing the related netdev object on shutdown
- avoid invalid memory access in case of error while allocating
bcast_own_sum when a new hard-interface is added, by Sven Eckelmann
- ensure originator address is updated in OMG/ELP packet content upon
primary interface address change, by Antonio Quartulli
- fix integer overflow when computing TQ metric (B.A.T.M.A.N. IV), by
Sven Eckelmann
- avoid race condition while adding new neigh_node which would result
in having two objects mapping to the same physical neighbour, by
Linus Lüssing
- ensure originator address is initialized in ELP packet content on
secondary interfaces, by Marek Lindner
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a patch to clean checkpatch warnings and errors
in the Space.c file.
Clean up the following warnings and errors.
WARNING :
* Block comments use * on subsequent lines
* Missing a blank line after declarations
* networking block comments don't use an empty /* line, use /*
* please, no space before tabs
* please, no spaces at the start of a line
* line over 80 characters
ERROR :
* code indent should use tabs where possible
* space prohibited after that open parenthesis '('
Signed-off-by: Amit Ghadge <amitg.b14@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This time round the update brings in following changes:
- New tegra driver for ADMA device
- Support for Xilinx AXI Direct Memory Access Engine and Xilinx AXI Central
Direct Memory Access Engine and few updates to this driver.
- New cyclic capability to sun6i and few updates.
- Slave-sg support in bcm2835.
- Updates to many drivers like designware, hsu, mv_xor, pxa, edma,
qcom_hidma & bam.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=0Sy7
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-4.7-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
"This time round the update brings in following changes:
- new tegra driver for ADMA device
- support for Xilinx AXI Direct Memory Access Engine and Xilinx AXI
Central Direct Memory Access Engine and few updates to this driver
- new cyclic capability to sun6i and few updates
- slave-sg support in bcm2835
- updates to many drivers like designware, hsu, mv_xor, pxa, edma,
qcom_hidma & bam"
* tag 'dmaengine-4.7-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (84 commits)
dmaengine: ioatdma: disable relaxed ordering for ioatdma
dmaengine: of_dma: approximate an average distribution
dmaengine: core: Use IS_ENABLED() instead of checking for built-in or module
dmaengine: edma: Re-evaluate errors when ccerr is triggered w/o error event
dmaengine: qcom_hidma: add support for object hierarchy
dmaengine: qcom_hidma: add debugfs hooks
dmaengine: qcom_hidma: implement lower level hardware interface
dmaengine: vdma: Add clock support
Documentation: DT: vdma: Add clock support for dmas
dmaengine: vdma: Add config structure to differentiate dmas
MAINTAINERS: Update Tegra DMA maintainers
dmaengine: tegra-adma: Add support for Tegra210 ADMA
Documentation: DT: Add binding documentation for NVIDIA ADMA
dmaengine: vdma: Add Support for Xilinx AXI Central Direct Memory Access Engine
Documentation: DT: vdma: update binding doc for AXI CDMA
dmaengine: vdma: Add Support for Xilinx AXI Direct Memory Access Engine
Documentation: DT: vdma: update binding doc for AXI DMA
dmaengine: vdma: Rename xilinx_vdma_ prefix to xilinx_dma
dmaengine: slave means at least one of DMA_SLAVE, DMA_CYCLIC
dmaengine: mv_xor: Allow selecting mv_xor for mvebu only compatible SoC
...
Eric Dumazet says:
====================
net: block BH in TCP callbacks
Four layers using TCP stack were assuming sk_callback_lock could
be locked using read_lock() in their handlers because TCP stack
was running with BH disabled.
This is no longer the case. Since presumably the rest could
also depend on BH being disabled, just use read_lock_bh().
Then each layer might consider switching to RCU protection
and no longer depend on BH.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
TCP stack can now run from process context.
Use read_lock_bh(&sk->sk_callback_lock) variant to restore previous
assumption.
Fixes: 5413d1babe ("net: do not block BH while processing socket backlog")
Fixes: d41a69f1d3 ("tcp: make tcp_sendmsg() aware of socket backlog")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jon Maloy <jon.maloy@ericsson.com>
Cc: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TCP stack can now run from process context.
Use read_lock_bh(&sk->sk_callback_lock) variant to restore previous
assumption.
Fixes: 5413d1babe ("net: do not block BH while processing socket backlog")
Fixes: d41a69f1d3 ("tcp: make tcp_sendmsg() aware of socket backlog")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TCP stack can now run from process context.
Use read_lock_bh() variant to restore previous assumption.
Fixes: 5413d1babe ("net: do not block BH while processing socket backlog")
Fixes: d41a69f1d3 ("tcp: make tcp_sendmsg() aware of socket backlog")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
iscsi_sw_tcp_data_ready() and iscsi_sw_tcp_state_change() were
using read_lock(&sk->sk_callback_lock) which is fine if caller
disabled BH.
TCP stack no longer has this requirement and can run from
process context.
Use read_lock_bh() variant to restore previous assumption.
Ideally this code could use RCU instead...
Fixes: 5413d1babe ("net: do not block BH while processing socket backlog")
Fixes: d41a69f1d3 ("tcp: make tcp_sendmsg() aware of socket backlog")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Mike Christie <michaelc@cs.wisc.edu>
Cc: Venkatesh Srinivas <venkateshs@google.com>
Acked-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
One is a fix for making sure that module signing still works when
coming from a different environment. If original keys are not found it
will warn and reset the keys to their default value.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXPf7XAAoJEKKk/i67LK/8HXYH+QH5Pp85FV3aA8rN4O/lnJyy
bz3bffB13GpO1tMFgqdoPjq41rRVJLIrCVrwypRP3KxnWyN520xkATi14um8eQr2
JfWimXDjX3qH++bqFAckvb++1pp0jMRVwNXsakQEvQGJTNVkdCsLgpSUObo9WSPy
JjphoX0+E/gh0qXrhNmGZDXFQT+YCKiVDAuyLjw+3GP3OXJUqQrQsqBTAcTgKgb2
fAKjvYOPptZ+GogZgqAUpx8+yxLBWHSj2PdGAvsCL5ZBYU9LEuq+VYS7XI50oTyT
5U+4DGdcee02EBgKP/CkhjeadmQTOSdRmN2c6ev41LebPjPPnTA7QJVp6yZZ7ko=
=ef99
-----END PGP SIGNATURE-----
Merge tag 'localmodconfig-v4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-kconfig
Pull localmodconfig updates from Steven Rostedt.
"Benjamin Poirier added some minor fixes and clean ups to
localmodconfig.
One is a fix for making sure that module signing still works when
coming from a different environment. If original keys are not found
it will warn and reset the keys to their default value"
* tag 'localmodconfig-v4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-kconfig:
localmodconfig: Fix whitespace repeat count after "tristate"
localmodconfig: Reset certificate paths
localmodconfig: Add missing $ to reference a variable
localmodconfig: Fix parsing of "help" text
localmodconfig: Recognize more keywords that end a menu entry
localmodconfig: Fix parsing of Kconfig "source" statements
(!count || count < 4) is always true.
So let's remove the coding which is dead at least since 2005.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
(a && a > 0) is equivalent to (a > 0).
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only dereference variable self after checking it is not NULL.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
If DEBUG is defined, a superfluous closing brace
is introduced.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- x86: miscellaneous fixes, AVIC support (local APIC virtualization,
AMD version)
- s390: polling for interrupts after a VCPU goes to halted state is
now enabled for s390; use hardware provided information about facility
bits that do not need any hypervisor activity, and other fixes for
cpu models and facilities; improve perf output; floating interrupt
controller improvements.
- MIPS: miscellaneous fixes
- PPC: bugfixes only
- ARM: 16K page size support, generic firmware probing layer for
timer and GIC
Christoffer Dall (KVM-ARM maintainer) says:
"There are a few changes in this pull request touching things outside
KVM, but they should all carry the necessary acks and it made the
merge process much easier to do it this way."
though actually the irqchip maintainers' acks didn't make it into the
patches. Marc Zyngier, who is both irqchip and KVM-ARM maintainer,
later acked at http://mid.gmane.org/573351D1.4060303@arm.com
"more formally and for documentation purposes".
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJXPJjyAAoJEL/70l94x66DhioH/j4fwQ0FmfPSM9PArzaFHQdx
LNE3tU4+bobbsy1BJr4DiAaOUQn3DAgwUvGLWXdeLiOXtoWXBiFHKaxlqEsCA6iQ
xcTH1TgfxsVoqGQ6bT9X/2GCx70heYpcWG3f+zqBy7ZfFmQykLAC/HwOr52VQL8f
hUFi3YmTHcnorp0n5Xg+9r3+RBS4D/kTbtdn6+KCLnPJ0RcgNkI3/NcafTemoofw
Tkv8+YYFNvKV13qlIfVqxMa0GwWI3pP6YaNKhaS5XO8Pu16HuuF1JthJsUBDzwBa
RInp8R9MoXgsBYhLpz3jc9vWG7G9yDl5LehsD9KOUGOaFYJ7sQN+QZOusa6jFgA=
=llO5
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Paolo Bonzini:
"Small release overall.
x86:
- miscellaneous fixes
- AVIC support (local APIC virtualization, AMD version)
s390:
- polling for interrupts after a VCPU goes to halted state is now
enabled for s390
- use hardware provided information about facility bits that do not
need any hypervisor activity, and other fixes for cpu models and
facilities
- improve perf output
- floating interrupt controller improvements.
MIPS:
- miscellaneous fixes
PPC:
- bugfixes only
ARM:
- 16K page size support
- generic firmware probing layer for timer and GIC
Christoffer Dall (KVM-ARM maintainer) says:
"There are a few changes in this pull request touching things
outside KVM, but they should all carry the necessary acks and it
made the merge process much easier to do it this way."
though actually the irqchip maintainers' acks didn't make it into the
patches. Marc Zyngier, who is both irqchip and KVM-ARM maintainer,
later acked at http://mid.gmane.org/573351D1.4060303@arm.com ('more
formally and for documentation purposes')"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (82 commits)
KVM: MTRR: remove MSR 0x2f8
KVM: x86: make hwapic_isr_update and hwapic_irr_update look the same
svm: Manage vcpu load/unload when enable AVIC
svm: Do not intercept CR8 when enable AVIC
svm: Do not expose x2APIC when enable AVIC
KVM: x86: Introducing kvm_x86_ops.apicv_post_state_restore
svm: Add VMEXIT handlers for AVIC
svm: Add interrupt injection via AVIC
KVM: x86: Detect and Initialize AVIC support
svm: Introduce new AVIC VMCB registers
KVM: split kvm_vcpu_wake_up from kvm_vcpu_kick
KVM: x86: Introducing kvm_x86_ops VCPU blocking/unblocking hooks
KVM: x86: Introducing kvm_x86_ops VM init/destroy hooks
KVM: x86: Rename kvm_apic_get_reg to kvm_lapic_get_reg
KVM: x86: Misc LAPIC changes to expose helper functions
KVM: shrink halt polling even more for invalid wakeups
KVM: s390: set halt polling to 80 microseconds
KVM: halt_polling: provide a way to qualify wakeups during poll
KVM: PPC: Book3S HV: Re-enable XICS fast path for irqfd-generated interrupts
kvm: Conditionally register IRQ bypass consumer
...
skb_splice_bits() returns int, kcm_splice_read() returns ssize_t,
both are signed.
We may need another patch to make them all ssize_t, but that
deserves a separated patch.
Fixes: 91687355b9 ("kcm: Splice support")
Reported-by: David Binderman <linuxdev.baldrick@gmail.com>
Cc: Tom Herbert <tom@herbertland.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ehea_get_port may return NULL. Do not dereference NULL value.
Fixes: 8c4877a412 ("ehea: Use the standard logging functions")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Thadeu Lima de Souza Cascardo <cascardo@debian.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In function bgx_lmac_handler only use a member of
lmac after checking it is not null.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Originally DSS only had DSI PLLs, and thus the DPI driver has functions
and variables that refer to DSI or DSI PLL. Now we support DSI, VIDEO
and HDMI PLLs, so it's time to remove the DSI references from the code.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Type A and B PLLs require a bit different calculations for the clock
rates. DPI driver supports only type A PLLs.
This patch adds support for the type B PLL.
Type B PLLs are simpler than type A, as type B can produce a good clock
for almost any rate. Thus we can just ask it to produce the pixel clock
and use one as LCK and PCK dividers.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
dss_pll_calc_b() takes HDMI TMDS clock rate as a parameter. To make
dss_pll_calc_b() usable for non-HDMI users, change the function to take
clkout rate as parameter, and also change the current users of
dss_pll_calc_b() to accommodate that.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Move hdmi_pll_compute(), used to calculate the config for HDMI PLL, from
hdmi_pll.c to pll.c, with the name of dss_pll_calc_b(), to make it
available to non-HDMI users.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add a "_a" postfix to the type A PLL calc functions, to differentiate
them from the type B PLL calculations which we will add shortly.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
To make it possible to use HDMI PLL for other video outputs than HDMI,
the HDMI PLL code needs to do runtime_get/put for the HDMI IP, so that
the IP (include the PLL) is enabled.
To do that we also need to store the HDMI pdev in the hdmi_pll_data.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
DPI driver uses a fixed clkout index, 0. This has worked fine as the
first clkout is usually used.
To generalize the code and to support additional clock sources, change
the code to use dss_pll_get_clkout_idx_for_src() to get the clkout
index.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We can clean up the DPI driver's clock source handling by using the
dss_clk_source instead of only a dss_pll pointer.
This will also make it possible to use additional clock sources, like
PLL1_3 or HDMI_PLL, which the code did not support earlier.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
With the new PLL helpers, we can clean up the dispc_fclk_rate(). This
will also make dispc_fclk_rate() support clock sources it didn't support
earlier.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
With the new PLL helpers, we can clean up the dispc_mgr_lclk_rate().
This will also make dispc_mgr_lclk_rate() support clock sources it
didn't support earlier.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add two PLL helper functions:
dss_pll_find_by_src() which returns the dss_pll for the given
dss_clk_source.
dss_pll_get_clkout_idx_for_src() which returns the clkout index for the
given dss_clk_source.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The code to set the clock muxes for DISPC's LCD clock inputs is very
confusing. Especially on DRA7, there's an additional clock muxing that
needs to be done, which at the moment is done in dpi.c using
dss_ctrl_pll_set_control_mux().
Clean this all up by:
- Using dss_clk_source instead of dss_pll_id, as dss_pll_id doesn't
specify the clock source quite correctly.
- Splitting the dss_select_lcd_clk_source() up into DSS version specific
helper functions.
- Using dss_ctrl_pll_set_control_mux() from the helper functions, so
that dpi.c doesn't have to call it.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
DSS uses two types of PLLs, type A (DSI & Video) and type B (HDMI). The
two types behave slightly differently, but we don't have the type of the
PLL available anywhere for the driver.
This patch adds an enum for the PLL type and a field in the PLL's HW
data to store it.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
enum dss_clk_source does not have values for all clock sources available
on OMAP4+ DSS versions. Add the missing clock sources.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The names of the enum dss_clk_source's values are legacy names, only
correct for OMAP3 DSS. Rename the names to more generic ones.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Now that there is no "non-generic" version of the function to get the
clock source name, lets rename dss_get_generic_clk_source_name() to
dss_get_clk_source_name().
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We have two functions to return a name for clock sources for debugging
purposes: dss_feat_get_clk_source_name() and
dss_get_generic_clk_source_name().
The former is supposed to return a DSS IP version specific name for the
clock source, and the latter is supposed to return a more generic name.
All this seems a bit pointless, so let's remove the former one.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
'enum omap_dss_clk_source' is internal to dss. Let's rename it to
'dss_clk_source' match our naming convention.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
At the moment 'enum omap_dss_clk_source' is in omapdss.h, shared by
omapdrm and omapfb. We're about to improve the omapdrm clock code, so we
need to make a separate copy of the enum for each driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Video pll hw data is missing bitfield definitions for clkout2 and
clkout3. We don't use those clkouts at the moment, so this has not
caused any issues.
Add the bitfields.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The 'gpbridge' name didn't relaly reflect what the bus is; which
is a bus for bridged-phy devices. So, rename all instances
of 'gpbridge' to more appropriate 'gbphy'
Testing Done:
Build and boot tested. 'lsgb' will stop displaying 'GPBridge' devices
until I change the library to reflect this change.
Signed-off-by: Sandeep Patil <patil_sandeep@projectara.com>
Suggested-by: Greg Kroah-Hartman <gregkh@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Pull MIPS updates from Ralf Baechle:
"This is the main pull request for MIPS for 4.7. Here's the summary of
the changes:
- ATH79: Support for DTB passuing using the UHI boot protocol
- ATH79: Remove support for builtin DTB.
- ATH79: Add zboot debug serial support.
- ATH79: Add initial support for Dragino MS14 (Dragine 2), Onion Omega
and DPT-Module.
- ATH79: Update devicetree clock support for AR9132 and AR9331.
- ATH79: Cleanup the DT code.
- ATH79: Support newer SOCs in ath79_ddr_ctrl_init.
- ATH79: Fix regression in PCI window initialization.
- BCM47xx: Move SPROM driver to drivers/firmware/
- BCM63xx: Enable partition parser in defconfig.
- BMIPS: BMIPS5000 has I cache filing from D cache
- BMIPS: BMIPS: Add cpu-feature-overrides.h
- BMIPS: Add Whirlwind support
- BMIPS: Adjust mips-hpt-frequency for BCM7435
- BMIPS: Remove maxcpus from BCM97435SVMB DTS
- BMIPS: Add missing 7038 L1 register cells to BCM7435
- BMIPS: Various tweaks to initialization code.
- BMIPS: Enable partition parser in defconfig.
- BMIPS: Cache tweaks.
- BMIPS: Add UART, I2C and SATA devices to DT.
- BMIPS: Add BCM6358 and BCM63268support
- BMIPS: Add device tree example for BCM6358.
- BMIPS: Improve Improve BCM6328 and BCM6368 device trees
- Lantiq: Add support for device tree file from boot loader
- Lantiq: Allow build with no built-in DT.
- Loongson 3: Reserve 32MB for RS780E integrated GPU.
- Loongson 3: Fix build error after ld-version.sh modification
- Loongson 3: Move chipset ACPI code from drivers to arch.
- Loongson 3: Speedup irq processing.
- Loongson 3: Add basic Loongson 3A support.
- Loongson 3: Set cache flush handlers to nop.
- Loongson 3: Invalidate special TLBs when needed.
- Loongson 3: Fast TLB refill handler.
- MT7620: Fallback strategy for invalid syscfg0.
- Netlogic: Fix CP0_EBASE redefinition warnings
- Octeon: Initialization fixes
- Octeon: Add DTS files for the D-Link DSR-1000N and EdgeRouter Lite
- Octeon: Enable add Octeon-drivers in cavium_octeon_defconfig
- Octeon: Correctly handle endian-swapped initramfs images.
- Octeon: Support CN73xx, CN75xx and CN78xx.
- Octeon: Remove dead code from cvmx-sysinfo.
- Octeon: Extend number of supported CPUs past 32.
- Octeon: Remove some code limiting NR_IRQS to 255.
- Octeon: Simplify octeon_irq_ciu_gpio_set_type.
- Octeon: Mark some functions __init in smp.c
- Octeon: Octeon: Add Octeon III CN7xxx interface detection
- PIC32: Add serial driver and bindings for it.
- PIC32: Add PIC32 deadman timer driver and bindings.
- PIC32: Add PIC32 clock timer driver and bindings.
- Pistachio: Determine SoC revision during boot
- Sibyte: Fix Kconfig dependencies of SIBYTE_BUS_WATCHER.
- Sibyte: Strip redundant comments from bcm1480_regs.h.
- Panic immediately if panic_on_oops is set.
- module: fix incorrect IS_ERR_VALUE macro usage.
- module: Make consistent use of pr_*
- Remove no longer needed work_on_cpu() call.
- Remove CONFIG_IPV6_PRIVACY from defconfigs.
- Fix registers of non-crashing CPUs in dumps.
- Handle MIPSisms in new vmcore_elf32_check_arch.
- Select CONFIG_HANDLE_DOMAIN_IRQ and make it work.
- Allow RIXI to be used on non-R2 or R6 cores.
- Reserve nosave data for hibernation
- Fix siginfo.h to use strict POSIX types.
- Don't unwind user mode with EVA.
- Fix watchpoint restoration
- Ptrace watchpoints for R6.
- Sync icache when it fills from dcache
- I6400 I-cache fills from dcache.
- Various MSA fixes.
- Cleanup MIPS_CPU_* definitions.
- Signal: Move generic copy_siginfo to signal.h
- Signal: Fix uapi include in exported asm/siginfo.h
- Timer fixes for sake of KVM.
- XPA TLB refill fixes.
- Treat perf counter feature
- Update John Crispin's email address
- Add PIC32 watchdog and bindings.
- Handle R10000 LL/SC bug in set_pte()
- cpufreq: Various fixes for Longson1.
- R6: Fix R2 emulation.
- mathemu: Cosmetic fix to ADDIUPC emulation, plenty of other small fixes
- ELF: ABI and FP fixes.
- Allow for relocatable kernel and use that to support KASLR.
- Fix CPC_BASE_ADDR mask
- Plenty fo smp-cps, CM, R6 and M6250 fixes.
- Make reset_control_ops const.
- Fix kernel command line handling of leading whitespace.
- Cleanups to cache handling.
- Add brcm, bcm6345-l1-intc device tree bindings.
- Use generic clkdev.h header
- Remove CLK_IS_ROOT usage.
- Misc small cleanups.
- CM: Fix compilation error when !MIPS_CM
- oprofile: Fix a preemption issue
- Detect DSP ASE v3 support:1"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (275 commits)
MIPS: pic32mzda: fix getting timer clock rate.
MIPS: ath79: fix regression in PCI window initialization
MIPS: ath79: make ath79_ddr_ctrl_init() compatible for newer SoCs
MIPS: Fix VZ probe gas errors with binutils <2.24
MIPS: perf: Fix I6400 event numbers
MIPS: DEC: Export `ioasic_ssr_lock' to modules
MIPS: MSA: Fix a link error on `_init_msa_upper' with older GCC
MIPS: CM: Fix compilation error when !MIPS_CM
MIPS: Fix genvdso error on rebuild
USB: ohci-jz4740: Remove obsolete driver
MIPS: JZ4740: Probe OHCI platform device via DT
MIPS: JZ4740: Qi LB60: Remove support for AVT2 variant
MIPS: pistachio: Determine SoC revision during boot
MIPS: BMIPS: Adjust mips-hpt-frequency for BCM7435
mips: mt7620: fallback to SDRAM when syscfg0 does not have a valid value for the memory type
MIPS: Prevent "restoration" of MSA context in non-MSA kernels
MIPS: cevt-r4k: Dynamically calculate min_delta_ns
MIPS: malta-time: Take seconds into account
MIPS: malta-time: Start GIC count before syncing to RTC
MIPS: Force CPUs to lose FP context during mode switches
...
userptr directly only uses drm_device in a single interface where it
meant to use drm_i915_private (everywhere else we have to derive it from
the drm_i915_gem_object and so require going from drm_device).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463671036-3235-1-git-send-email-chris@chris-wilson.co.uk
- Support for EZChip (now Mellanox) NPS-400 Network processor based on ARC700
http://www.mellanox.com/related-docs/prod_npu/PB_NPS-400.pdf
- NPS interrupt controller and clocksource drivers
- ARC timers probed off DT
- ARC iqrchips switching to linear domain (upgrade from legacy domains)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=pnAx
-----END PGP SIGNATURE-----
Merge tag 'arc-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC updates from Vineet Gupta:
"We have a relatively big changeset for ARC for 4.7.
The highlight is support for EZChip (now Mellanox) NPS-400 network
processor, a 400-Gb throughput C-programmable packet processor based
on ARC700 cores from Synopsys. See
http://www.mellanox.com/related-docs/prod_npu/PB_NPS-400.pdf
Also present are irqchip and clocksource drivers for NPS as agreed
with respective maintainers to go via ARC tree due to an soc header
dependency. I have the needed ACKs from Jason, Marc, Daniel. You
might run into a trivial merge conflict in drivers/irqchip/*
This EZChip platform support required some deep changes in ARC
architecture code and also opportunity to cleanup past sins (legacy
irq domains, missing irq domain lookup, hard coded timer irqs...)
Summary:
- Support for EZChip (now Mellanox) NPS-400 Network processor based
on ARC700
- NPS interrupt controller and clocksource drivers
- ARC timers probed off DT
- ARC iqrchips switching to linear domain (upgrade from legacy
domains)"
* tag 'arc-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc: (37 commits)
arc: axs103_smp: Fix CPU frequency to 100MHz for dual-core
arc: axs10x: Add DT bindings for I2S PLL Clock
ARC: pae: STRICT_MM_TYPECHECKS was broken
ARC: Add eznps platform to Kconfig and Makefile
ARC: [plat-eznps] Use dedicated COMMAND_LINE_SIZE
ARC: [plat-eznps] Use dedicated cpu_relax()
ARC: [plat-eznps] Use dedicated identity auxiliary register.
ARC: [plat-eznps] Use dedicated SMP barriers
ARC: [plat-eznps] Use dedicated atomic/bitops/cmpxchg
ARC: [plat-eznps] Use dedicated user stack top
ARC: [plat-eznps] Add eznps platform
ARC: [plat-eznps] Add eznps board defconfig and dts
ARC: Mark secondary cpu online only after all HW setup is done
ARC: rwlock: disable interrupts in !LLSC variant
ARC: Make vmalloc size configurable
ARC: clean out UAPI byteorder.h clean off Kconfig symbol
irqchip: add nps Internal and external irqchips
clocksource: Add NPS400 timers driver
soc: Support for EZchip SoC
Documentation: Add EZchip vendor to binding list
...
