For a bit of extra paranoia make sure the display irqs are all cleared
before we enabled them when turning on the power well. This should
really be the case already since the power well was off which resets
everything.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460382992-28728-6-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
During runtime PM we'll be reinitializing interrupt support from the
ground up. However since the display power well will be off at that
time, well end up with a ton of unclaimed register accesses from the
display irq setup. Since we turned off the power well already before
runtime suspend, we've flagged display irqs as disabled during runtime
PM transitions. So we can just check that flag to see if we should do
skip display irqs during irq setup.
During driver load display irqs will be flagged as enabled since we've
turned on the power well already, however the power well code will have
skipped the display irq setup since irq support as a whole wasn't yet
enabled when the power well was enabled. So we'll want to do the display
irq setup in that case.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=94164
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460382992-28728-4-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
The vlv/chv display irq setup was a bit of mess after I ran out of steam
when working on it last. Fix it up so that we just have a _reset() and
_postinstall() hooks for the display irqs, and use those consistently.
v2: Clear out pipestat_irq_mask[] and PIPE_FIFO_UNDERRUN_STATUS in
vlv_display_irq_reset() (Imre)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com> (v1)
Link: http://patchwork.freedesktop.org/patch/msgid/1460476574-1921-1-git-send-email-ville.syrjala@linux.intel.com
The underruns we were seeing when enabling eDP port A on ILK seem to
have been caused by prematurely clearing the LP1+ watermark values when
disabling LP1+ watermarks. Now that the watermarks are handled
properly, we can rip out the underrun suppression around the port A
enable.
We still need to worry about the underruns on FDI when enabling
the eDP PLL. But as Bspec tells us, we can avoid that by a vblank
wait on the pipe driving FDI just prior to enabling the eDP PLL.
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459536799-18109-4-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Once again ILK is unhappy if we clear out the LP1+ watermark levels
outright, and instead we must disable the levels we don't want while
still leaving the actual programmed watermark levels intact.
Fixes underruns on the already enabled pipe when programming watermarks
while enabling the second pipe.
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Matt Roper <matthew.d.roper@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=93787
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459536799-18109-3-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Take a bigger hammer to the underrun suppression on ILK. Instead of
trying to suppress them at specific points in the modeset sequence just
silence them across the entire sequence. This gets rid of some underruns
at least on my ILK. Note that this changes SNB and IVB to follow the
same approach just to keep the code less convoluted. The difference is
that on those platforms we won't suppress CPU underruns for port A since
it doesn't seem to be necessary.
My ILK has port A eDP and two PCH HDMI ports, so I can't be sure this is
as effective on other PCH port types. Perhaps we still need some of
Daniel's extra vblank waits [2]?
I've still been able to trigger an underrun on the other pipe, but
fixing that perhaps needs the LP1+ disable trick I implemented here [1]
which never got merged.
A few details which hamper stress testing on my ILK are that sometimes
the PCH transcoder gets messed up and refuses to shut down, and sometimes
even the panel power sequencer apparently gets stuck on the always on
position.
[1] https://lists.freedesktop.org/archives/intel-gfx/2014-March/041317.html
[2] https://lists.freedesktop.org/archives/intel-gfx/2016-January/086397.html
v2: Add a note that we also get underruns when enabling PCH ports
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> (v1)
Link: http://patchwork.freedesktop.org/patch/msgid/1459536799-18109-2-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Commit 947e9762a8 ("writeback: update wb_over_bg_thresh() to use
wb_domain aware operations") unintentionally changed this function's
meaning from "are there more dirty pages than the background writeback
threshold" to "are there more dirty pages than the writeback threshold".
The background writeback threshold is typically half of the writeback
threshold, so this had the effect of raising the number of dirty pages
required to cause a writeback worker to perform background writeout.
This can cause a very severe performance regression when a BDI uses
BDI_CAP_STRICTLIMIT because balance_dirty_pages() and the writeback worker
can now disagree on whether writeback should be initiated.
For example, in a system having 1GB of RAM, a single spinning disk, and
a "pass-through" FUSE filesystem mounted over the disk, application code
mmapped a 128MB file on the disk and was randomly dirtying pages in that
mapping.
Because FUSE uses strictlimit and has a default max_ratio of only 1%,
in balance_dirty_pages, thresh is ~200, bg_thresh is ~100, and the
dirty_freerun_ceiling is the average of those, ~150. So, it pauses the
dirtying processes when we have 151 dirty pages and wakes up a
background writeback worker. But the worker tests the wrong threshold
(200 instead of 100), so it does not initiate writeback and just
returns.
Thus, balance_dirty_pages keeps looping, sleeping and then waking up the
worker who will do nothing. It remains stuck in this state until the few
dirty pages that we have finally expire and we write them back for that
reason. Then the whole process repeats, resulting in near-zero
throughput through the FUSE BDI.
The fix is to call the parameterized variant of wb_calc_thresh, so that
the worker will do writeback if the bg_thresh is exceeded which was the
bahavior before the referenced commit.
Fixes: 947e9762a8 ("writeback: update wb_over_bg_thresh() to use
wb_domain aware operations")
Signed-off-by: Howard Cochran <hcochran@kernelspring.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@fb.com>
Johan Hedberg says:
====================
pull request: bluetooth-next 2016-04-12
Here's a set of Bluetooth & 802.15.4 patches intended for the 4.7 kernel:
- Fix for race condition in vhci driver
- Memory leak fix for ieee802154/adf7242 driver
- Improvements to deal with single-mode (LE-only) Bluetooth controllers
- Fix for allowing the BT_SECURITY_FIPS security level
- New BCM2E71 ACPI ID
- NULL pointer dereference fix fox hci_ldisc driver
Let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
dmaengine has various device callbacks and exposes helper
functions to invoke these. These helpers should check if channel,
device and callback is valid or not before invoking them.
Reported-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Commit 254d4d111e ("drm/exynos: Add dependency for G2D in Kconfig") made
the DRM_EXYNOS_G2D symbol to only be selectable if the s5p-g2d V4L2 driver
is not enabled, since both use the same HW IP block.
But added the dependency as depends on !VIDEO_SAMSUNG_S5P_G2D which isn't
correct since Kconfig expressions are not boolean but tristate. So it will
only evaluate to 'n' if VIDEO_SAMSUNG_S5P_G2D=y but it will evaluate to m
if VIDEO_SAMSUNG_S5P_G2D=m.
This means that both the V4L2 and DRM drivers can be enabled if the former
is enabled as a module, which is not what we want.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The ARM TWD interrupt is a private peripheral interrupt (PPI) and per
the ARM GIC documentation, whether the type for PPIs can be set is
IMPLEMENTATION DEFINED. For Tegra20/30 devices the PPI type cannot be
set and so when we attempt to set the type for the ARM TWD interrupt it
fails. This has gone unnoticed because it fails silently and because we
cannot re-configure the type it has had no impact. Nevertheless fix the
type for the TWD interrupt so that it matches the hardware configuration.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
For Tegra boards, the device-tree alias serial0 is used for the console
and so add the stdout-path information so that the console no longer
needs to be passed via the kernel boot parameters.
This has been tested on boards, tegra20-trimslice, tegra30-beaver,
tegra114-dalmore and tegra124-jetson-tk1.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Though the keyboard and other driver will continue to support the legacy
"gpio-key,wakeup", "nvidia,wakeup-source" boolean property to enable the
wakeup source, "wakeup-source" is the new standard binding.
This patch replaces all the legacy wakeup properties with the unified
"wakeup-source" property in order to avoid any further copy-paste
duplication.
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: linux-tegra@vger.kernel.org
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Watchdog support was added to the timer block with Tegra30. Tegra20 did
not have this yet. However, the Tegra114 and Tegra124 DTSI files had an
entry in the compatible string list for "nvidia,tegra20-timer", but not
for "nvidia,tegra30-timer", which is why watchdog support isn't enabled
on them.
Fix this by adding an entry for "nvidia,tegra30-timer" to the compatible
string list of the timer block on Tegra114 and Tegra124.
This allows the watchdog to work on Jetson TK1.
Signed-off-by: Maarten Lankhorst <dev@mblankhorst.nl>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This patch enables the APB DMA high speed UARTs of the Jetson TK1. So
far, they were only enabled in NVidia's official BSP.
Those additional UARTs are exposed on the expansion connector J3A2:
UART1:
Pin 41: BR_UART1_TXD
Pin 44: BR_UART1_RXD
UART2:
Pin 65: UART2_RXD
Pin 68: UART2_TXD
Pin 71: UART2_CTS_L
Pin 74: UART2_RTS_L
Signed-off-by: Ralf Ramsauer <ralf@ramses-pyramidenbau.de>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The comment about the 8250 vs. APB DMA-enabled UART devices that was
added for Tegra20 and Tegra30 in commit b6551bb933 ("ARM: tegra: dts:
add aliases and DMA requestor for serial controller") introduced a typo
that has since spread to various other DTS include files. Fix all
occurrences of this typo.
Signed-off-by: Ralf Ramsauer <ralf@ramses-pyramidenbau.de>
Acked-by: Stephen Warren <swarren@nvidia.com>
[treding@nvidia.com: amend subject, add commit message]
Signed-off-by: Thierry Reding <treding@nvidia.com>
These two are both ARMv7 SoCs. They need not explicitly select
ARM_L1_CACHE_SHIFT_6 because it is enabled along with CPU_V7.
Refer to commit a092f2b153 ("ARM: 7291/1: cache: assume 64-byte L1
cachelines for ARMv7 CPUs").
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Rather than blindly waking up all forcewake domains on command
submission, we can teach each engine what is (or are) the correct
one to take.
On platforms with multiple forcewake domains like VLV, CHV, SKL
and BXT, this has the potential of lowering the GPU and CPU
power use and submission latency.
To implement it we add a function named
intel_uncore_forcewake_for_reg whose purpose is to query which
forcewake domains need to be taken to read or write a specific
register with raw mmio accessors.
These enables the execlists engine setup to query which
forcewake domains are relevant per engine on the currently
running platform.
v2:
* Kerneldoc.
* Split from intel_uncore.c macro extraction, WARN_ON,
no warns on old platforms. (Chris Wilson)
v3:
* Single domain per engine, mention all registers,
bi-directional function and a new name, fix handling
of gen6 and gen7 writes. (Chris Wilson)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1460468251-14069-1-git-send-email-tvrtko.ursulin@linux.intel.com
Chris Wilson points out that we can remove them from the array
since they are always written to with raw accessors.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Knowledge of which register per platform belonds in which
forcewake domain was embedded in the MMIO accessors themselves.
Extract it into standalone macros so they can be used from
new code in the following patches.
This causes GCC to compile some of the MMIO accessors slightly
differently and grows the code a tiny amount. But none of the
growth is on the fast-path so it does not matter hugely.
Affected sizes before:
00000000000026f0 00000000000001a5 t gen6_read16
0000000000002390 00000000000001a5 t gen6_read32
00000000000028a0 00000000000001a5 t gen6_read64
00000000000061d0 000000000000019e t gen8_write16
0000000000006510 000000000000019d t gen8_write32
0000000000006370 000000000000019d t gen8_write64
00000000000021f0 000000000000019d t gen8_write8
Affected sizes after:
0000000000002840 00000000000001aa t gen6_read16
00000000000024e0 00000000000001a9 t gen6_read32
00000000000029f0 00000000000001a9 t gen6_read64
0000000000004f20 00000000000001b5 t gen8_write16
0000000000004ba0 00000000000001b4 t gen8_write32
00000000000050e0 00000000000001b4 t gen8_write64
0000000000004d60 00000000000001b4 t gen8_write8
Other MMIO accessors are not affected in size.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Enable FHANDLE, CGROUPS, BLK_DEV_BSG and DEVTMPFS as recommended by
systemd (which also matches the multi_v7 defconfig). Also enable IPV6,
which defaults to 'y' by now.
Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Currently only the ondemand and performance CPUFreq policy governors are
enabled in multi_v7 defconfig. But the other governors are also useful
for some cases, enable them to allow users change the default if needed.
The options are enabled as module to keep the kernel image size minimal.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Currently only the ondemand and performance CPUFreq policy governors are
enabled in the Exynos defconfig. But the other governors are also useful
for some cases, enable them to allow users change the default if needed.
The options are enabled as module to keep the kernel image size minimal.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
The Exynos4412-based Trats2 board has Asahi Kasei AK 3-Axis
Magnetometer, CM36651 proximity/ambient light sensor, MMS114 touchscreen
and Wolfson Microelectronics WM1811 CODEC. Enable them in defconfig to
get some testing coverage and use its features.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
This enum is already perfectly aliased to enum nl80211_band, and
the only reason for it is that we get IEEE80211_NUM_BANDS out of
it. There's no really good reason to not declare the number of
bands in nl80211 though, so do that and remove the cfg80211 one.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The "ret = regmap_write()" assignment was missing so this error message
is never printed.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
We accidentally return success instead of a negative error code here.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Commit 1feafd3afd ("drm/exynos: add
exynos5420 support for fimd") add support for Exynos 5420 SoC, but it
broke enabling display clock feature because of incorrect condition
check. This patch fixes it, so display is working again on platforms
requiring display clock control (i.e. Exynos5250-based SNOW platform).
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Fbdev code should be compiled only if CONFIG_DRM_FBDEV_EMULATION option
is enabled. The patch fixes exynos-drm code trying to manipulate
fbdev data which is not initialized in case CONFIG_DRM_FBDEV_EMULATION
is disabled.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
exynos_plane_mode_set should use adjusted_mode from the same atomic state as
plane state. Otherwise it will result in incorrect behavior in case
crtc mode changes.
The patch fixes bug with black console framebuffer in case of command mode
panels.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
gcc-6 warns about a pointless loop in exynos_drm_subdrv_open:
drivers/gpu/drm/exynos/exynos_drm_core.c: In function 'exynos_drm_subdrv_open':
drivers/gpu/drm/exynos/exynos_drm_core.c:104:199: error: self-comparison always evaluates to false [-Werror=tautological-compare]
list_for_each_entry_reverse(subdrv, &subdrv->list, list) {
Here, the list_for_each_entry_reverse immediately terminates because
the subdrv pointer is compared to itself as the loop end condition.
If we were to take the current subdrv pointer as the start of the
list (as we would do if list_for_each_entry_reverse() was not a macro),
we would iterate backwards over the &exynos_drm_subdrv_list anchor,
which would be even worse.
Instead, we need to use list_for_each_entry_continue_reverse()
to go back over each subdrv that was successfully opened until
the first entry.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
A non-privileged user can create a netlink socket with the same port_id as
used by an existing open nl80211 netlink socket (e.g. as used by a hostapd
process) with a different protocol number.
Closing this socket will then lead to the notification going to nl80211's
socket release notification handler, and possibly cause an action such as
removing a virtual interface.
Fix this issue by checking that the netlink protocol is NETLINK_GENERIC.
Since generic netlink has no notifier chain of its own, we can't fix the
problem more generically.
Fixes: 026331c4d9 ("cfg80211/mac80211: allow registering for and sending action frames")
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Ivanov <dima@ubnt.com>
[rewrite commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The roaming cases for the Connect command were not fully covered and
neither Connect nor Associate command uses of the prev_bssid parameter
were very clear. Add details to describe how the prev_bssid argument is
supposed to be used and when the driver should use association or
reassociation.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As the vast majority of users do not use the domain id variable,
we can eliminate it from the iterator and also change the latter
using the same principle as was recently done for for_each_engine.
For a couple of callers which do need the domain mask, store it
in the domain array (which already has the domain id), then both
can be retrieved thence.
Result is clearer code and smaller generated binary, especially
in the tight fw get/put loops. Also, relationship between domain
id and mask is no longer assumed in the macro.
v2: Improve grammar in the commit message and rename the
iterator to for_each_fw_domain_masked for consistency.
(Dave Gordon)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Dave Gordon <david.s.gordon@intel.com>
Because it is based on jiffies, current implementation releases the
forcewake at any time between straight away and between 1ms and 10ms,
depending on the kernel configuration (CONFIG_HZ).
This is probably not what has been desired, since the dynamics of keeping
parts of the GPU awake should not be correlated with this kernel
configuration parameter.
Change the auto-release mechanism to use hrtimers and set the timeout to
1ms with a 1ms of slack. This should make the GPU power consistent
across kernel configs, and timer slack should enable some timer coalescing
where multiple force-wake domains exist, or with unrelated timers.
For GlBench/T-Rex this decreases the number of forcewake releases from
~480 to ~300 per second, and for a heavy combined OGL/OCL test from
~670 to ~360 (HZ=1000 kernel).
Even though this reduction can be attributed to the average release period
extending from 0-1ms to 1-2ms, as discussed above, it will make the
forcewake timeout consistent for different CONFIG_HZ values.
Real life measurements with the above workload has shown that, with this
patch, both manage to auto-release the forcewake between 2-4 times per
10ms, even though the number of forcewake gets is dramatically different.
T-Rex requests between 5-10 explicit gets and 5-10 implict gets in each
10ms period, while the OGL/OCL test requests 250 and 380 times in the same
period.
The two data points together suggest that the nature of the forwake
accesses is bursty and that further changes and potential timeout
extensions, or moving the start of timeout from the first to the last
automatic forcewake grab, should be carefully measured for power and
performance effects.
v2:
* Commit spelling. (Dave Gordon)
* More discussion on numbers in the commit. (Chris Wilson)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Dave Gordon <david.s.gordon@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Update the URLs for alsa-info.sh and hda-emu. Also drop the
alsa-driver snapshot URL since it's been discontinued recently.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The calls for capture_hook were missing in dyn_adc_capture_pcm_prepare
and cleanup callbacks. Luckily there are no users of the capture
hooks with dyn-adc PCM, so far, thus this doesn't change the behavior
of existing devices, but it's a fix for a future usage.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Only really needed for fbdev emulation at 8bpp. And bochs doesn't do
that. And either way bochs only does 32bit rgb, so this is all pretty
much wasted dead code.
The only consideration is that we need to not set up any gamma size
either.
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Dave Airlie <airlied@redhat.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459331485-28376-5-git-send-email-daniel.vetter@ffwll.ch
The kfree() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Fix bogus memsets pointed out by sparse:
linux-v4.3/drivers/macintosh/rack-meter.c:157:15: warning: memset with byte count of 0
linux-v4.3/drivers/macintosh/rack-meter.c:158:15: warning: memset with byte count of 0
Probably "&" is mistyped "*"; use ARRAY_SIZE to make it more safe.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Limit idle ticks to total ticks. This prevents the annoying rackmeter
leds fully ON / OFF blinking state that happens on fully idling
G5 Xserve systems.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Sometimes when sparse warns about undefined symbols, it isn't
because they should have 'static' added, it's because they're
overriding __weak symbols defined elsewhere, and the header has
been missed.
Fix a few of them by adding appropriate headers.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
As sparse suggests, these should be made static.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Reviewed-by: Stewart Smith <stewart@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
__drm_atomic_helper_plane_destroy_state calls
drm_framebuffer_unreference, which means that if drm_framebuffer_free
is called before plane->destroy freed memory will be accessed.
A similar case happens for the blob list, which was freed before the
crtc state was, resulting in the unreference_blob from crtc_destroy_state
pointing to garbage memory causing another opportunity for a GPF.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1458657734-21866-1-git-send-email-maarten.lankhorst@linux.intel.com
