The wopcm registers are write-once, so any write after the first one
will just be ignored. The registers survive a GPU reset but not
always a suspend/resume cycle, so to keep things simple keep the
writes in the intel_uc_init_hw function instead of moving it earlier
to make sure we attempt them every time we try to load GuC.
Cc: Jeff McGee <jeff.mcgee@intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1491524332-23860-1-git-send-email-daniele.ceraolospurio@intel.com
This patch utilizes the new PLL clk notifier to gate then ungate the
PLL CPU clock after rate changes. This should mitigate the system
hangs observed after the introduction of cpufreq for the A33.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
In common PLL designs, changes to the dividers take effect almost
immediately, while changes to the multipliers (implemented as
dividers in the feedback loop) take a few cycles to work into
the feedback loop for the PLL to stablize.
Sometimes when the PLL clock rate is changed, the decrease in the
divider is too much for the decrease in the multiplier to catch up.
The PLL clock rate will spike, and in some cases, might lock up
completely. This is especially the case if the divider changed is
the pre-divider, which affects the reference frequency.
This patch introduces a clk notifier callback that will gate and
then ungate a clk after a rate change, effectively resetting it,
so it continues to work, despite any possible lockups. Care must
be taken to reparent any consumers to other temporary clocks during
the rate change, and that this notifier callback must be the first
to be registered.
This is intended to fix occasional lockups with cpufreq on newer
Allwinner SoCs, such as the A33 and the H3. Previously it was
thought that reparenting the cpu clock away from the PLL while
it stabilized was enough, as this worked quite well on the A31.
On the A33, hangs have been observed after cpufreq was recently
introduced. With the H3, a more thorough test [1] showed that
reparenting alone isn't enough. The system still locks up unless
the dividers are limited to 1.
A hunch was if the PLL was stuck in some unknown state, perhaps
gating then ungating it would bring it back to normal. Tests
done by Icenowy Zheng using Ondrej's test firmware shows this
to be a valid solution.
[1] http://www.spinics.net/lists/arm-kernel/msg552501.html
Reported-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: Icenowy Zheng <icenowy@aosc.io>
Tested-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The ccu-sun9i-a80 driver uses the ccu_mult_ops struct, but unlike the other
users it doesen't select the corresponding Kconfig symbol under which the
struct is compiled in.
This results in the following link error with CONFIG_SUN9I_A80_CCU=y and
CONFIG_SUNXI_CCU_MULT=n:
drivers/built-in.o:(.data+0x2d638): undefined reference to 'ccu_mult_ops'
Fix this by explicitly selecting CONFIG_SUNXI_CCU_MULT like the other
users of the struct.
Signed-off-by: Tobias Regnery <tobias.regnery@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
With CONFIG_RESET_CONTROLLER=n we get the following link error in the
sunxi-ng clk driver:
drivers/built-in.o: In function `sunxi_ccu_probe':
mux-core.c:(.text+0x12fe68): undefined reference to 'reset_controller_register'
mux-core.c:(.text+0x12fe68): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol 'reset_controller_register'
Fix this by adding the appropriate select statement.
Signed-off-by: Tobias Regnery <tobias.regnery@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This adds a driver for the Nokia H4+ protocol, which is used
at least on the Nokia N9, N900 & N950.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Add binding document for serial bluetooth chips using
Nokia H4+ protocol.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Geminilake vendor nid is different from other Skylake variants, but rest
of the initialization code is same.
So a variable is added in hdmi_spec to store the platform specific vendor
nid and move the initialization code to a helper function to be used by
both platform specific init.
Fixes: 126cfa2f5e ("ALSA: hda: Add Geminilake HDMI codec ID")
Signed-off-by: Ander Conselvan De Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Jaikrishna Nemallapudi <jaikrishnax.nemallapudi@intel.com>
Cc: Senthilnathan Veppur <senthilnathanx.veppur@intel.com>
Cc: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
-----BEGIN PGP SIGNATURE-----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=A/S/
-----END PGP SIGNATURE-----
Merge tag 'drm-fixes-for-v4.11-rc7' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"i915, gvt, nouveau, udl and etnaviv fixes.
I was away the end of last week, so some of these would have been in
rc6, and it's Easter from tomorrow, so I decided I better dequeue what
I have now.
The nouveau changes, just add a hw enable for GP107 display (like a
pci id addition really), and fix a couple of regressions. i915 has
some more gvt fixes, along with a few run of the mill ones, the rcu
one seems like a few people have hit it.
Otherwise a small udl and small etnaviv fix"
* tag 'drm-fixes-for-v4.11-rc7' of git://people.freedesktop.org/~airlied/linux: (22 commits)
drm/etnaviv: fix missing unlock on error in etnaviv_gpu_submit()
drm/udl: Fix unaligned memory access in udl_render_hline
drm/i915: Don't call synchronize_rcu_expedited under struct_mutex
drm/i915: Suspend GuC prior to GPU Reset during GEM suspend
drm/nouveau: initial support (display-only) for GP107
drm/nouveau/kms/nv50: fix double dma_fence_put() when destroying plane state
drm/nouveau/kms/nv50: fix setting of HeadSetRasterVertBlankDmi method
drm/nouveau/mmu/nv4a: use nv04 mmu rather than the nv44 one
drm/nouveau/mpeg: mthd returns true on success now
drm/i915/gvt: set the correct default value of CTX STATUS PTR
drm/i915/gvt: Fix firmware loading interface for GVT-g golden HW state
drm/i915: Use a dummy timeline name for a signaled fence
drm/i915: Ironlake do_idle_maps w/a may be called w/o struct_mutex
drm/i915/gvt: remove the redundant info NULL check
drm/i915/gvt: adjust mem size for low resolution type
drm/i915: Avoid lock dropping between rescheduling
drm/i915/gvt: exclude cfg space from failsafe mode
drm/i915/gvt: Activate/de-activate vGPU in mdev ops.
drm/i915/execlists: Wrap tail pointer after reset tweaking
drm/i915/perf: remove user triggerable warn
...
This contain a fix for the atomic update support recently added to the
Rockchip driver where the clock reference count would become unbalanced
and result in the clock feeding the PWM to always be disabled.
Another fix to the Intel LPSS driver that adds an update bit quirk
required for a specific configuration.
-----BEGIN PGP SIGNATURE-----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=ftQo
-----END PGP SIGNATURE-----
Merge tag 'pwm/for-4.11-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm fixes from Thierry Reding:
"This contain a fix for the atomic update support recently added to
the Rockchip driver where the clock reference count would become
unbalanced and result in the clock feeding the PWM to always be
disabled.
Another fix to the Intel LPSS driver that adds an update bit quirk
required for a specific configuration"
* tag 'pwm/for-4.11-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm:
pwm: rockchip: State of PWM clock should synchronize with PWM enabled state
pwm: lpss: Set enable-bit before waiting for update-bit to go low
pwm: lpss: Split Tangier configuration
When clang detects a non-boolean constant in a logical operation it
generates a 'constant-logical-operand' warning. In
ieee80211_try_rate_control_ops_get() the result of strlen(<const str>)
is used in a logical operation, clang resolves the expression to an
(integer) constant at compile time when clang's builtin strlen function
is used.
Change the condition to check for strlen() > 0 to make the constant
operand boolean and thus avoid the warning.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reserving a runtime region results in splitting the EFI memory
descriptors for the runtime region. This results in runtime region
descriptors with bogus memory mappings, leading to interesting crashes
like the following during a kexec:
general protection fault: 0000 [#1] SMP
Modules linked in:
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.11.0-rc1 #53
Hardware name: Wiwynn Leopard-Orv2/Leopard-DDR BW, BIOS LBM05 09/30/2016
RIP: 0010:virt_efi_set_variable()
...
Call Trace:
efi_delete_dummy_variable()
efi_enter_virtual_mode()
start_kernel()
? set_init_arg()
x86_64_start_reservations()
x86_64_start_kernel()
start_cpu()
...
Kernel panic - not syncing: Fatal exception
Runtime regions will not be freed and do not need to be reserved, so
skip the memmap modification in this case.
Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk>
Cc: <stable@vger.kernel.org> # v4.9+
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Dave Young <dyoung@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Jones <pjones@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Fixes: 8e80632fb2 ("efi/esrt: Use efi_mem_reserve() and avoid a kmalloc()")
Link: http://lkml.kernel.org/r/20170412152719.9779-2-matt@codeblueprint.co.uk
Signed-off-by: Ingo Molnar <mingo@kernel.org>
As those debug messages might appear in every timer call for scheduler,
it's too noisy, eat too much log and aren't meaningful. So remove them.
Cc: Ping Gao <ping.a.gao@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
We want dax capable drivers to be able to publish a set of dax
operations [1]. However, we do not want to further abuse block_devices
to advertise these operations. Instead we will attach these operations
to a dax device and add a lookup mechanism to go from block device path
to a dax device. A dax capable driver like pmem or brd is responsible
for registering a dax device, alongside a block device, and then a dax
capable filesystem is responsible for retrieving the dax device by path
name if it wants to call dax_operations.
For now, we refactor the dax pseudo-fs to be a generic facility, rather
than an implementation detail, of the device-dax use case. Where a "dax
device" is just an inode + dax infrastructure, and "Device DAX" is a
mapping service layered on top of that base 'struct dax_device'.
"Filesystem DAX" is then a mapping service that layers a filesystem on
top of that same base device. Filesystem DAX is associated with a
block_device for now, but perhaps directly to a dax device in the
future, or for new pmem-only filesystems.
[1]: https://lkml.org/lkml/2017/1/19/880
Suggested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
In preparation for introducing a struct dax_device type to the kernel
global type namespace, rename dax_dev to dev_dax. A 'dax_device'
instance will be a generic device-driver object for any provider of dax
functionality. A 'dev_dax' object is a device-dax-driver local /
internal instance.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
A couple of minor improvements to the debug output in the fault handlers:
a) Print the region alignment and fault size when we sent a SIGBUS
because the region alignment is greater than the fault size.
b) Fix the message in the PFN_{DEV|MAP} check.
c) Additionally print the fault size enum value in the huge fault handler.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The default case for dax_dev_huge_fault() fault size handling mistakenly
returns when it should unlock. This is not a problem in practice since
the only three possible fault sizes are handled. Going forward, if the
core mm adds a new fault size beyond pte, pmd, or pud device-dax should
abort VM_FAULT_SIGBUS requests not VM_FAULT_FALLBACK since device-dax
guarantees a configured fault granularity for all faults.
Signed-off-by: Pushkar Jambhlekar <pushkar.iit@gmail.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Provide a replacement pgoff_to_phys() that translates an nfit_test
resource (allocated by vmalloc()) to a pfn.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Providing mechanism to clear poison list via the ndctl ND_CMD_CLEAR_ERROR
call. We will update the poison list and also the badblocks at region level
if the region is in dax mode or in pmem mode and not active. In other
words we force badblocks to be cleared through write requests if the
address is currently accessed through a block device, otherwise it can
only be done via the ioctl+dsm path.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Adding sysfs attribute in order to export the physical address of the
region. This is for supporting of user app poison clear via
ND_IOCTL_CLEAR_ERROR.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
badblocks sysfs file will be export at region level. When nvdimm event
notifier happens for NVDIMM_REVALIATE_POISON, the badblocks in the
region will be updated.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Calls to acpi_get_table() must be paired with acpi_put_table() to undo
the mapping established by acpi_tb_acquire_table().
It turns out this has no effect in practice since the NFIT will already
be mapped to support the /sys/firmware/acpi/tables/NFIT attribute in
sysfs.
Fixes: 6b11d1d677 ("ACPI / osl: Remove acpi_get_table_with_size()/early_acpi_os_unmap_memory() users")
Cc: Lv Zheng <lv.zheng@intel.com>
Reported-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The newline in MODULE_PARM_DESC causes modinfo to print the parameter
data type on a separate line, which is different from all the other
module parameters and could potentially cause a problem for someone
parsing the output of modinfo.
Signed-off-by: Linda Knippers <linda.knippers@hpe.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Provide the ability to request a default DSM family. If it is not
supported, then fall back to the normal discovery order.
This is helpful for testing platforms that support multiple DSM
families. It will also allow administrators to request the DSM family
that their management tools support, which may not be the first one
found using the current discovery order.
Signed-off-by: Linda Knippers <linda.knippers@hpe.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
As it is today, we can't enable or test new NVDIMM management functions
provided by new firmware and tools without changing the kernel. We also
can't prevent documented DSM functions from being called in the case of
buggy firmware. This patch provides a module parameter that overrides
the DSM function mask that is built into the kernel.
If the "disable_vendor_specific" module parameter is also used we ignore
the new parameter.
Signed-off-by: Linda Knippers <linda.knippers@hpe.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Commit 10c7e20b2f (ACPI / scan: fix enumeration (visited) flags for
bus rescans) attempted to fix a problem with ACPI-based enumerateion
of I2C/SPI devices, but it forgot to ensure that the visited flag
will be set for all of the other enumerated devices, so fix that.
Fixes: 10c7e20b2f (ACPI / scan: fix enumeration (visited) flags for bus rescans)
Link: https://bugzilla.kernel.org/show_bug.cgi?id=194885
Reported-and-tested-by: Kevin Locke <kevin@kevinlocke.name>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: 4.8+ <stable@vger.kernel.org> # 4.8+
/sys/firmware/acpi/hotplug/force_remove was presumably added to support
auto offlining in the past. This is, however, inherently dangerous for
some hotplugable resources like memory. The memory offlining fails when
the memory is still in use and cannot be dropped or migrated. If we
ignore the failure we are basically allowing for subtle memory
corruption or a crash.
We have actually noticed the later while hitting BUG() during the memory
hotremove (remove_memory):
ret = walk_memory_range(PFN_DOWN(start), PFN_UP(start + size - 1), NULL,
check_memblock_offlined_cb);
if (ret)
BUG();
it took us quite non-trivial time realize that the customer had
force_remove enabled. Even if the BUG was removed here and we could
propagate the error up the call chain it wouldn't help at all because
then we would hit a crash or a memory corruption later and harder to
debug. So force_remove is unfixable for the memory hotremove. We haven't
checked other hotplugable resources to be prone to a similar problems.
Remove the force_remove functionality because it is not fixable currently.
Keep the sysfs file and report an error if somebody tries to enable it.
Encourage users to report about the missing functionality and work with
them with an alternative solution.
Reviewed-by: Lee, Chun-Yi <jlee@suse.com>
Signed-off-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The schedutil governor reduces frequencies too fast in some
situations which cases undesirable performance drops to
appear.
To address that issue, make schedutil reduce the frequency slower by
setting it to the average of the value chosen during the previous
iteration of governor computations and the new one coming from its
frequency selection formula.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=194963
Reported-by: John <john.ettedgui@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
There is a report that after commit 27622b061e ("cpufreq: Convert
to hotplug state machine"), the normal CPU offline/online cycle
fails on some platforms.
According to the ftrace result, this problem was triggered on
platforms using acpi-cpufreq as the default cpufreq driver,
and due to the lack of some ACPI freq method (eg. _PCT),
cpufreq_online() failed and returned a negative value, so the CPU
hotplug state machine rolled back the CPU online process. Actually,
from the user's perspective, the failure of cpufreq_online() should
not prevent that CPU from being brought up, although cpufreq might
not work on that CPU.
BTW, during system startup cpufreq_online() is not invoked via CPU
online but by the cpufreq device creation process, so the APs can be
brought up even though cpufreq_online() fails in that stage.
This patch ignores the return value of cpufreq_online/offline() and
lets the cpufreq framework deal with the failure. cpufreq_online()
itself will do a proper rollback in that case and if _PCT is missing,
the ACPI cpufreq driver will print a warning if the corresponding
debug options have been enabled.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=194581
Fixes: 27622b061e ("cpufreq: Convert to hotplug state machine")
Reported-and-tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Chen Yu <yu.c.chen@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: 4.9+ <stable@vger.kernel.org> # 4.9+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Most CPUs do not have a hardware c1 counter,
and so turbostat derives c1 residency:
c1 = TSC - MPERF - other_core_cstate_counters
As it is not possible to atomically read these coutners,
measurement jitter can case this calcuation to "go negative"
when very close to 0. Turbostat detect that case and
simply prints c1 = 0.00%
But that check neglected to account for systems where the TSC
crystal clock domain and the MPERF BCLK domain are differ by
a small amount. That allowed very small negative c1 numbers
to escape this check and be printed as huge positve numbers.
This code begs for a bit of cleanup, but this patch
is the minimal change to fix the issue.
Signed-off-by: Len Brown <len.brown@intel.com>
Add GFX%rc6 and GFXMHz to the column descriptions section
of the turbostat man page.
Signed-off-by: Doug Smythies <dsmythies@telus.net>
Signed-off-by: Len Brown <len.brown@intel.com>
cpu0: MSR_IA32_TEMPERATURE_TARGET: 0x00641400 (100 C)
cpu0: MSR_IA32_PACKAGE_THERM_STATUS: 0x884b0800 (25 C)
cpu0: MSR_IA32_PACKAGE_THERM_INTERRUPT: 0x00000003 (100 C, 100 C)
Enable the same per-core output, but hide it behind --debug
because it is too verbose on big systems.
Signed-off-by: Len Brown <len.brown@intel.com>
While the current SDM is silent on the matter, the Core and GFX
RAPL power meters on SKL and KBL appear to work -- so show them.
Reported-by: Yaroslav Isakov <yaroslav.isakov@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
GP107 modesetting support (just recognising the chipset, no other changes until 4.12)
a couple of regression fixes, one of them a rather serious double-free issue that appeared in 4.10.
* 'linux-4.11' of git://github.com/skeggsb/linux:
drm/nouveau: initial support (display-only) for GP107
drm/nouveau/kms/nv50: fix double dma_fence_put() when destroying plane state
drm/nouveau/kms/nv50: fix setting of HeadSetRasterVertBlankDmi method
drm/nouveau/mmu/nv4a: use nv04 mmu rather than the nv44 one
drm/nouveau/mpeg: mthd returns true on success now
drm/i915 fixes for v4.11-rc7
one rcu related fix, and a few GVT fixes.
* tag 'drm-intel-fixes-2017-04-12' of git://anongit.freedesktop.org/git/drm-intel:
drm/i915: Don't call synchronize_rcu_expedited under struct_mutex
drm/i915: Suspend GuC prior to GPU Reset during GEM suspend
drm/i915/gvt: set the correct default value of CTX STATUS PTR
drm/i915/gvt: Fix firmware loading interface for GVT-g golden HW state
drm/i915: Use a dummy timeline name for a signaled fence
drm/i915: Ironlake do_idle_maps w/a may be called w/o struct_mutex
drm/i915/gvt: remove the redundant info NULL check
drm/i915/gvt: adjust mem size for low resolution type
drm/i915: Avoid lock dropping between rescheduling
drm/i915/gvt: exclude cfg space from failsafe mode
drm/i915/gvt: Activate/de-activate vGPU in mdev ops.
drm/i915/execlists: Wrap tail pointer after reset tweaking
drm/i915/perf: remove user triggerable warn
drm/i915/perf: destroy stream on sample_flags mismatch
drm/i915: Align "unfenced" tiled access on gen2, early gen3
With commit 23dac14d05 ("MIPS: PCI: Use struct list_head lists") new
controllers are added after the specified head where they where added
before the specified head previously.
Use list_add_tail to restore the former order.
This patches fixes the following PCI error on lantiq:
pci 0000:01:00.0: BAR 0: error updating (0x1c000004 != 0x000000)
Fixes: 23dac14d05 ("MIPS: PCI: Use struct list_head lists")
Signed-off-by: Mathias Kresin <dev@kresin.me>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/15808/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commit 41c594ab65 ("[MIPS] MT: Improved multithreading support.")
added an else case to an if statement in do_page_fault() (which has
since gained 2 leading underscores) for some unclear reason. If the
condition in the if statement evaluates true then we execute a goto &
branch elsewhere anyway, so the else has no effect. Combined with an #if
0 block with misleading indentation introduced in the same commit it
makes the code less clear than it could be.
Remove the unnecessary else statement & de-indent the printk within
the #if 0 block in order to make the code easier for humans to parse.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: trivial@kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/15842/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
