The fast path has a single unlikely() test for any error bit,
calling into a helper that sets the appropriate statistics.
The various netdev_info aren't particularly interesting. If
we want to differentiate the various length errors later we
can introduce driver specific stats using ethtool.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Read the descriptor field only once and check for IP header
checksum errors as well
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can occasionally fail to allocate new RX buffers at
runtime or when starting the driver. At the moment the
latter just fails to open which is fine but the former
leaves stale DMA pointers in the ring.
Instead, use a scratch page and have all RX ring descriptors
point to it by default unless a proper buffer can be allocated.
It will help later on when re-initializing the whole ring
at runtime on link changes since there is no clean failure
path there unlike open().
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We don't support jumbo frames, we will never receive a
fragmented packet, the RX buffer is always big enough,
if not then it's a runaway packet that can be dropped.
So take out the loop that handles such things in
ftgmac100_rx_packet() which will help with subsequent
simplifications and improvements to the RX path
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
RX moderation default parameters shouldn't be set in
mlx5e_build_rx_cq_param since it would reset the values every time on
netdev open/close. Instead, it should be set in
mlx5e_set_rx_cq_mode_params which is called on driver load only.
Fixes: 6a9764efb2 ("net/mlx5e: Isolate open_channels from priv->params")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reuse the code for mlx5e_alloc_cq and mlx5e_alloc_drop_cq, as they
have a similar flow.
Prior to this patch, the CQEs in the "drop CQ" were not initialized,
fixed
it with the shared flow of alloc CQ. This is not a critical bug as the
RQ connected to this CQ never moved to RTS, but still better to have
this right.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add the board id (PSID) to the firmware-version field
in the ethtool -i (driver information).
The PSID is shown in parentheses, next to the fw-version.
$ ethtool -i ens6
firmware-version: 12.14.1101 (MT_2190110032)
Signed-off-by: Inbar Karmy <inbark@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
FW version should be reported as X.Y.ZZZZ, add leading zeroes to sub
minor in order to fix it.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Make mlx5e_modify_rqs_vsd a static function and remove from en.h in
order to reduce redundant exposure of functions.
Signed-off-by: Guy Ergas <guye@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add support for rx-fcs flag from ethtool.
In case this flag is set, update all RQs to scatter the FCS data into
the packet.
Signed-off-by: Guy Ergas <guye@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Rename the ConnectX-5 PCIe 4.0 to be ConnectX-5 Ex.
Also add the upcoming ConnectX-6 and it's VF IDs to the list.
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
This adds support for the Winstar Display Co. WF35LTIACD 3.5" QVGA TFT
LCD panel, which can be supported by the simple panel driver.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Winstar Display Corp. is specialized in LCD displays for embedded
products.
cf: http://www.winstar.com.tw
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Sitronix ST7789v controller is used to drive 240x320 LCD panels through
various interfaces, including SPI and RGB/Parallel.
The current driver is configuring it for the latter. Support for tinyDRM
can always be added later.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Sitronix ST7789V is an LCD panel controller, controlled over SPI, that
can drive 18-bits 240x320 LCD displays.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
- Rework the inline directory verifier to avoid crashes on disk corruption
- Don't change file size when punching holes w/ KEEP_SIZE
- Close a kernel memory exposure bug
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=QdXx
-----END PGP SIGNATURE-----
Merge tag 'xfs-4.11-fixes-3' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux
Pull XFS fixes from Darrick Wong:
"Here are three more fixes for 4.11.
The first one reworks the inline directory verifier to check the
working copy of the directory metadata and to avoid triggering a
periodic crash in xfs/348. The second patch fixes a regression in hole
punching at EOF that corrupts files; and the third patch closes a
kernel memory disclosure bug.
Summary:
- rework the inline directory verifier to avoid crashes on disk
corruption
- don't change file size when punching holes w/ KEEP_SIZE
- close a kernel memory exposure bug"
* tag 'xfs-4.11-fixes-3' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
xfs: fix kernel memory exposure problems
xfs: Honor FALLOC_FL_KEEP_SIZE when punching ends of files
xfs: rework the inline directory verifiers
Add basic support for the PCM-947 carrier board, a RK3288 based development
board made by PHYTEC. This board works in a combination with
the phyCORE-RK3288 System on Module.
Following interfaces and devices are available on the PCM-947 carrier board:
- 2x UART
- micro SDMMC
- USB host and USB otg
- USB 3503 HSIC hub
- Ethernet
- 2nd alternative KSZ9031 ethernet phy
- Display connectors: PHYTEC LVDS, DDG LVDS, parallel signals, HDMI
- Parallel Camera CIF
- SGTL5000-32QFN audio codec
- 4x LEDs connected via PCA9533
- 2 user buttons
- Expansion connectors for WiFi and other modules
- RTC RV-4162-C7
- Resistive touch STMPE811
- EEPROM M24C32
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
- bump version strings, by Simon Wunderlich
- Code and Style cleanups, by Sven Eckelmann (5 patches)
- Remove an unneccessary memset, by Tobias Klauser
- DAT and BLA optimizations for various corner cases, by Andreas Pape
(5 patches)
- forward/rebroadcast packet restructuring, by Linus Luessing
(2 patches)
- ethtool cleanup and remove unncessary code, by Sven Eckelmann
(4 patches)
- use net_device_stats from net_device instead of private copy,
by Tobias Klauser
-----BEGIN PGP SIGNATURE-----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=r99K
-----END PGP SIGNATURE-----
Merge tag 'batadv-next-for-davem-20170406' of git://git.open-mesh.org/linux-merge
Simon Wunderlich says:
====================
This feature/cleanup patchset includes the following patches:
- bump version strings, by Simon Wunderlich
- Code and Style cleanups, by Sven Eckelmann (5 patches)
- Remove an unneccessary memset, by Tobias Klauser
- DAT and BLA optimizations for various corner cases, by Andreas Pape
(5 patches)
- forward/rebroadcast packet restructuring, by Linus Luessing
(2 patches)
- ethtool cleanup and remove unncessary code, by Sven Eckelmann
(4 patches)
- use net_device_stats from net_device instead of private copy,
by Tobias Klauser
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add support for MIPI-DSI based S6E3HA2 AMOLED panel
driver. This panel has 1440x2560 resolution in 5.7-inch physical
panel in the TM2 device.
Signed-off-by: Donghwa Lee <dh09.lee@samsung.com>
Signed-off-by: Hyungwon Hwang <human.hwang@samsung.com>
Signed-off-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add documentation for the PCM-947 carrier board, a RK3288 based
development board made by PHYTEC.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Yuval Mintz says:
====================
qed: Misc cleanups and fixes
Patches #1 and #2 revolve around register access performed by driver;
The first merely adds some debug, while the second does some fixing
of incorrect PTT usage as well as preventing issues similar to those
fixed by 6f437d4319 ("qed: Don't use attention PTT for configuring BW").
Patch #3 better configures HW for architecture where cacheline isn't 64B.
Patches #4-#8 all affect iSCSI related functionaility -
adding statistics information [both to driver & management firmware],
passing information on number of resources to qedi, and simplifying
the Out-of-order implementation in SW.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
No need to maintain the various open archipelagos as a list -
The maximal number of them is known, and we can use the CID
as key for random-access into the array.
Signed-off-by: Michal Kalderon <Michal.Kalderon@caviumc.om>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Management firmware can query for some basic iSCSI-related statistics.
Provide those just as we do for other protocols.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that management firmware is capable of telling us the number of CQs
available for a given PF, qed needs to communicate the number to qedi
so it would know have many to use.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Firmware provides a statistic for the number of out-of-order isles
it used - fill it in the iscsi-related statistics.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before initializing the chip's engine, driver currently closes a set
of registers on the HW's ingress flow to prevent packets from slipping
in while they're not supposed to.
This configuration is insufficient, as there are some scenarios where
packets would still arrive even when said registers are set,
but the management firmware already closes other per-port registers
that do suffice, making this setting unnecessray.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Default HW configuration is optimal for an architecture where cache
line size is 64B.
During chip initialization, properly initialize the cache line size
in HW to avoid possible redundant PCI transactions.
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to access HW registers driver needs to acquire a PTT entry
[mapping between bar memory and internal chip address].
Since acquiring PTT entries could fail [at least in theory] as their
number is finite and other flows can hold them, we reserve special PTT
entries for 'important' enough flows - ones we want to guarantee that
would not be susceptible to such issues.
One such special entry is the 'main' PTT which is meant to be used in
flows such as chip initialization and de-initialization.
However, there are other flows that are also using that same entry
for their own purpose, and might run concurrently with the original
flows [notice that for most cases using the main-ptt by mistake, such
a race is still impossible, at least today].
This patch re-organizes the various functions that currently use the
main_ptt in one of two ways:
- If a function shouldn't use the main_ptt it starts acquiring and
releasing it's own PTT entry and use it instead. Notice if those
functions previously couldn't fail, they now can [as acquisition
might fail].
- Change the prototypes so that the main_ptt would be received as
a parameter [instead of explicitly accessing it].
This prevents the future risk of adding codes that introduces new
use-cases for flows using the main_ptt, ones that might be in race
with the actual 'main' flows.
Signed-off-by: Rahul Verma <Rahul.Verma@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PTT entries are per-hwfn; If some errneous flow is trying
to use a PTT belonging to a differnet hwfn warn user, as this
can break every register accessing flow later and is very hard
to root-cause.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The phyCORE-RK3288 is a SoM (System on Module) containing a RK3288 SoC.
The module can be connected to different carrier boards.
It can be also equipped with different RAM, SPI flash and eMMC variants.
The Rapid Development Kit option is using the following setup:
- 1 GB DDR3 RAM (2 Banks)
- 1x 4 KB EEPROM
- DP83867 Gigabit Ethernet PHY
- 16 MB SPI Flash
- 4 GB eMMC Flash
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add simple-panel support for the Ampire AM-480272H3TMQW-T01H, which is a
4.3" WQVGA panel.
Signed-off-by: Yannick Fertre <yannick.fertre@st.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
-----BEGIN PGP SIGNATURE-----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=JnXV
-----END PGP SIGNATURE-----
Merge tag 'rxrpc-rewrite-20170406' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
David Howells says:
====================
rxrpc: Miscellany
Here's a set of patches that make some minor changes to AF_RXRPC:
(1) Store error codes in struct rxrpc_call::error as negative codes and
only convert to positive in recvmsg() to avoid confusion inside the
kernel.
(2) Note the result of trying to abort a call (this fails if the call is
already 'completed').
(3) Don't abort on temporary errors whilst processing challenge and
response packets, but rather drop the packet and wait for
retransmission.
And also adds some more tracing:
(4) Protocol errors.
(5) Received abort packets.
(6) Changes in the Rx window size due to ACK packet information.
(7) Client call initiation (to allow the rxrpc_call struct pointer, the
wire call ID and the user ID/afs_call pointer to be cross-referenced).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds documentation of device tree bindings for the WVGA panel
Ampire AM-480272H3TMQW-T01H.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Yannick Fertre <yannick.fertre@st.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The OMAP driver has its own OF graph helpers that are similar to the
common helpers. This commit replaces most of the calls with the common
helpers. There's still a couple of custom helpers left, but the driver
needs more extensive changes to get rid of them.
In dss_init_ports, we invert the loop, looping through the known ports
and matching them to DT nodes rather than looping thru DT nodes and
matching them to the ports.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Similar to the previous commit, convert drivers open coding OF graph
parsing to use drm_of_find_panel_or_bridge instead.
This changes some error messages to debug messages (in the graph core).
Graph connections are often "no connects" depending on the particular
board, so we want to avoid spurious messages. Plus the kernel is not a
DT validator.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
[seanpaul dropped rockchip changes since they're now obsolete]
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Convert drivers to use the new of_graph_get_remote_node() helper
instead of parsing the endpoint node and then getting the remote device
node. Now drivers can just specify the device node and which
port/endpoint and get back the connected remote device node. The details
of the graph binding are nicely abstracted into the core OF graph code.
This changes some error messages to debug messages (in the graph core).
Graph connections are often "no connects" depending on the particular
board, so we want to avoid spurious messages. Plus the kernel is not a
DT validator.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Liviu Dudau <liviu.dudau@arm.com>
Tested-by: Eric Anholt <eric@anholt.net>
Tested-by: Jyri Sarha <jsarha@ti.com>
Tested by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Many drivers have a common pattern of searching the OF graph for either an
attached panel or bridge and then finding the DRM struct for the panel
or bridge. Also, most drivers need to handle deferred probing when the
DRM device is not yet instantiated. Create a common function,
drm_of_find_panel_or_bridge, to find the connected node and the
associated DRM panel or bridge device.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
[seanpaul dropped extern from drm_of.h]
Signed-off-by: Sean Paul <seanpaul@chromium.org>
For drm_of_find_panel_or_bridge() added in the next commit, an empty
version of of_drm_find_panel is needed for !CONFIG_DRM_PANEL.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
The atomic_check function is useful for implementing properties, but
it can be used for other connector modeset related checks as well.
Similar to plane check functions, on a modeset atomic_check() is always
called.
Changes since v1:
- Make sure atomic_check() is called on any modeset.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1491477543-31257-5-git-send-email-maarten.lankhorst@linux.intel.com
Now that handle_conflicting_encoders no longer touches active state,
so there's no need to do the check quite that late any more.
Doing it with all the other checks makes it a lot more clear what the
below block tries to accomplish, and this feels like a better place to
put the check.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1491477543-31257-4-git-send-email-maarten.lankhorst@linux.intel.com
Now that handle_conflicting_encoders cannot disable crtc's any more
it makes sense to set all the changed flags in 1 place.
This makes the code slightly less magical.
The (now removed) comment is out of date. The only reason the
active_changed was set late was because handle_conflicting_encoders
could disable connectors. This is no longer the case,
and we can put everything in 1 place.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1491477543-31257-3-git-send-email-maarten.lankhorst@linux.intel.com
Currently we use a flag to change behavior in atomic commit
whether a conflicting encoder should be enabled or disabled.
This is used for the legacy set_config helper, which disables
connectors that have a conflicting encoder but not part of the
active crtc list.
There's no need for this to be handled in atomic commit, it
could be done in the set_config helper instead. This will
let the atomic check function reject any conflicting encoders,
while set_config can disable conflicting crtc's. This makes it
possible to recalculate the changed flags in 1 loop.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1491477543-31257-2-git-send-email-maarten.lankhorst@linux.intel.com
Commit f6988cb63a ("team: don't call netdev_change_features under
team->lock") fixed the issue calling netdev_change_features under
team->lock for team_compute_features.
But there are still two places where it calls netdev_change_features
under team->lock, team_port_add and team_port_del. It may cause a
dead lock when the slave port with LRO enabled is added.
This patch is to fix this dead lock by moving netdev_change_features
out of team_port_add and team_port_del, and call it after unlocking
the team lock.
Reported-by: Patrick Talbert <ptalbert@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now sctp doesn't check sock's state before listening on it. It could
even cause changing a sock with any state to become a listening sock
when doing sctp_listen.
This patch is to fix it by checking sock's state in sctp_listen, so
that it will listen on the sock with right state.
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
100GbE Intel Wired LAN Driver Updates 2017-04-05
This series contains updates to fm10k only.
Phil Turnbull from Oracle fixes an issue where the argument provided to
FM10K_REMOVED macro was not what was expecting.
Jake modifies the driver to replace the bitwise operators and defines with
a BITMAP and enumeration values to avoid race conditions. Also future
proof the driver so that developers do not have to remember to re-size the
bitmaps when adding new values. Fixed the wording of a code comment to
avoid stating that we return a value for a void function.
Ngai-Mint makes sure that when configuring the receive ring, we make sure
the receive queue is disabled. Fixed an issue where interfaces were
resetting because the transmit mailbox FIFO was becoming full since the
host was not ready, so ensure the host is ready before queueing up
mailbox messages.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Legacy drivers insist that we really take all the locks in this path,
and the harm in doing so is minimal.
v2: Like git add, it exists :(
Fixes: 2ceb585a95 ("drm: Add explicit acquire ctx handling around ->set_config")
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: David Airlie <airlied@linux.ie>
Cc: dri-devel@lists.freedesktop.org
Cc: Alex Deucher <alexdeucher@gmail.com>
Reported-by: Alex Deucher <alexdeucher@gmail.com>
Acked-and-tested-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170406190654.6733-1-daniel.vetter@ffwll.ch
R. Parameswaran says:
====================
L2TP:Adjust intf MTU, add underlay L3, L2 hdrs.
Existing L2TP kernel code does not derive the optimal MTU for Ethernet
pseudowires and instead leaves this to a userspace L2TP daemon or
operator. If an MTU is not specified, the existing kernel code chooses
an MTU that does not take account of all tunnel header overheads, which
can lead to unwanted IP fragmentation. When L2TP is used without a
control plane (userspace daemon), we would prefer that the kernel does a
better job of choosing a default pseudowire MTU, taking account of all
tunnel header overheads, including IP header options, if any. This patch
addresses this.
Change-set is organized as a two part patch series, with one patch
introducing a new kernel function to compute the IP overhead on a
socket, and the other patch using this new kernel function to compute
the default L2TP MTU for an Ethernet pseudowire.
Existing code also seems to assume an Ethernet (non-jumbo) underlay. The
change proposed here uses the PMTU mechanism and the dst entry in the
L2TP tunnel socket to directly pull up the underlay MTU (as the baseline
number on top of which the encapsulation headers are factored in).
An default MTU value of 1500 bytes is assumed as a fallback only if
this fails.
Fixed the kbuild test robot error in the previous posting.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Existing L2TP kernel code does not derive the optimal MTU for Ethernet
pseudowires and instead leaves this to a userspace L2TP daemon or
operator. If an MTU is not specified, the existing kernel code chooses
an MTU that does not take account of all tunnel header overheads, which
can lead to unwanted IP fragmentation. When L2TP is used without a
control plane (userspace daemon), we would prefer that the kernel does a
better job of choosing a default pseudowire MTU, taking account of all
tunnel header overheads, including IP header options, if any. This patch
addresses this.
Change-set here uses the new kernel function, kernel_sock_ip_overhead(),
to factor the outer IP overhead on the L2TP tunnel socket (including
IP Options, if any) when calculating the default MTU for an Ethernet
pseudowire, along with consideration of the inner Ethernet header.
Signed-off-by: R. Parameswaran <rparames@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
