As per recent revisions of the datasheet.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Consolidate SH_CLK_CPG under ARCH_SHMOBILE_LEGACY so it can
be shared by the legacy ARM mach-shmobile support code.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Consolidate CPU_V7 under ARCH_SHMOBILE_LEGACY so it can
be shared by the legacy ARM mach-shmobile support code.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Adjust the ARM mach-shmobile Kconfig bits to only
select PM_RMOBILE in case of legacy. This allows us
to enable partial multiplatform support for various
SoCs before Power Domains DT bindings are finalized.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a CONFIG_PM_RMOBILE entry and enable it for R-Mobile
SoCs in case CONFIG_PM is set. Consolidate Makefile power
management objects and get rid of #ifdefs in the C code.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a CONFIG_PM_RCAR entry and enable it for R-Car
Generation 1 or 2 in case CONFIG_PM or CONFIG_SMP
is set. Consolidate power management objects and
get rid of #ifdefs in the C code.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a Kconfig entry for R-Car Generation 2 SoCs that
enables CMT timer and the IRQC interrupt driver.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a Kconfig entry for R-Car Generation 1 SoCs that
enables TMU timer and the INTC IRQPIN driver.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a Kconfig entry for R-Mobile SoCs that enables
both CMT and TMU timers. Interrupt controller varies
with SoC version so it is excluded.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Clevo W350etq's EC will not produce GPE interrupt some time after
booting. The ACPI notify event won't trigger when the issue takes
place. After debugging, adding msi quirk for the machine can fix
the issue. This patch is to add msi quirk for the machine.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=77431
Reported-and-tested-by: qbanin@gmail.com
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://bugs.freedesktop.org/show_bug.cgi?id=81515
Reported-and-tested-by: Hohahiu <rakothedin@gmail.com>
Cc: 3.16+ <stable@vger.kernel.org> # 3.16+
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Some laptops have a working acpi_video backlight control, and using native
backlight on these causes a regression where backlight control does not work
when userspace is not handling brightness key events. Disable native_backlight
on these to fix this.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=81691
Reported-and-tested-by: Andre Müller <andre.muller@web.de>
Cc: 3.16+ <stable@vger.kernel.org> # 3.16+
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit 751109aad5 ("ACPI / video: Change the default for
video.use_native_backlight to 1") has changed the default for
use_native_backlight from 0 to 1, but instead of changing
use_native_backlight_dmi to true, and leaving use_native_backlight_param at -1,
it has changed use_native_backlight_param to 1.
This causes acpi_video_use_native_backlight() to always think that a value was
specified through the param, making it impossible to add a dmi based quirk
to force 0 now that the default is 1.
This fixes this by restoring the use_native_backlight_param default to -1, and
instead setting the use_native_backlight_dmi default to true.
Fixes: 751109aad5 (ACPI / video: Change the default for video.use_native_backlight to 1)
Cc: 3.16+ <stable@vger.kernel.org> # 3.16+
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Adds ACPICA kernel runtime support to validate contents/format
of the _DSD package, similar to the iASL support. Ported by
Mika Westerberg.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reuse the path object in ext4_move_extents() so we don't unnecessarily
free and reallocate it.
Also clean up the get_ext_path() wrapper so that it has the same
semantics of freeing the path object on error as ext4_ext_find_extent().
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Now that the semantics of ext4_ext_find_extent() are much cleaner,
it's safe and more efficient to reuse the path object across the
multiple calls to ext4_ext_find_extent() in ext4_ext_shift_extents().
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
This adds additional safety in case for some reason we end reusing a
path structure which isn't big enough for current depth of the inode.
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Teach ext4_ext_drop_refs() to accept a NULL argument, much like
kfree(). This allows us to drop a lot of checks to make sure path is
non-NULL before calling ext4_ext_drop_refs().
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
In nearly all of the calls to ext4_ext_find_extent() where the caller
is trying to recycle the path object, ext4_ext_drop_refs() gets called
to release the buffer heads before the path object gets overwritten.
To simplify things for the callers, and to avoid the possibility of a
memory leak, make ext4_ext_find_extent() responsible for dropping the
buffers.
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Drop EXT4_EX_NOFREE_ON_ERR from ext4_ext_create_new_leaf(),
ext4_split_extent(), ext4_convert_unwritten_extents_endio().
This requires fixing all of their callers to potentially
ext4_ext_find_extent() to free the struct ext4_ext_path object in case
of an error, and there are interlocking dependencies all the way up to
ext4_ext_map_blocks(), ext4_swap_extents(), and
ext4_ext_remove_space().
Once this is done, we can drop the EXT4_EX_NOFREE_ON_ERR flag since it
is no longer necessary.
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
The function ext4_convert_initialized_extents() is only called by a
single function --- ext4_ext_convert_initalized_extents(). Inline the
code and get rid of the unnecessary bits in order to simplify the code.
Rename ext4_ext_convert_initalized_extents() to
convert_initalized_extents() since it's a static function that is
actually only used in a single caller, ext4_ext_map_blocks().
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Right now, there are a places where it is all to easy to leak memory
on an error path, via a usage like this:
struct ext4_ext_path *path = NULL
while (...) {
...
path = ext4_ext_find_extent(inode, block, path, 0);
if (IS_ERR(path)) {
/* oops, if path was non-NULL before the call to
ext4_ext_find_extent, we've leaked it! :-( */
...
return PTR_ERR(path);
}
...
}
Unfortunately, there some code paths where we are doing the following
instead:
path = ext4_ext_find_extent(inode, block, orig_path, 0);
and where it's important that we _not_ free orig_path in the case
where ext4_ext_find_extent() returns an error.
So change the function signature of ext4_ext_find_extent() so that it
takes a struct ext4_ext_path ** for its third argument, and by
default, on an error, it will free the struct ext4_ext_path, and then
zero out the struct ext4_ext_path * pointer. In order to avoid
causing problems, we add a flag EXT4_EX_NOFREE_ON_ERR which causes
ext4_ext_find_extent() to use the original behavior of forcing the
caller to deal with freeing the original path pointer on the error
case.
The goal is to get rid of EXT4_EX_NOFREE_ON_ERR entirely, but this
allows for a gentle transition and makes the patches easier to verify.
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Commit b8a8684502 introduced an accidental flag aliasing between
EXT4_EX_NOCACHE and EXT4_GET_BLOCKS_CONVERT_UNWRITTEN.
Fortunately, this didn't introduce any untorward side effects --- we
got lucky. Nevertheless, fix this and leave a warning to hopefully
avoid this from happening in the future.
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
We accidently aliased EXT4_EX_NOCACHE and EXT4_GET_CONVERT_UNWRITTEN
falgs, which apparently was hiding a bug that was unmasked when this
flag aliasing issue was addressed (see the subsequent commit). The
reproduction case was:
fsx -N 10000 -l 500000 -r 4096 -t 4096 -w 4096 -Z -R -W /vdb/junk
... which would cause fsx to report corruption in the data file.
The fix we have is a bit of an overkill, but I'd much rather be
conservative for now, and we can optimize ZERO_RANGE_FL handling
later. The fact that we need to zap the extent_status cache for the
inode is unfortunate, but correctness is far more important than
performance.
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: Namjae Jeon <namjae.jeon@samsung.com>
Pull irq handling fixlet from Thomas Gleixner:
"Just an export for an interrupt flow handler which is now used in gpio
modules"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irq: Export handle_fasteoi_irq
These board specific delays are now configured through micrel's specific
DT bindings (see Documentation/devicetree/bindings/net/micrel-ksz9021.txt).
Remove this phy fixup registration from sama5 DT machine file to keep it
as generic as possible.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Tested-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Add ethernet-phy nodes and specify phy interrupt (connected to pin PB25)
and board specific timing configs.
Atmel has two different HW designs for its CPU modules: the first one
(produced by Embest) is connecting PHYAD[0-2] pins to pull up resistors
and the other one (produced by Ronetix) is connecting PHYAD0 to a pull up
resistor and PHYAD[1-2] to pull down resistors.
As a result, Ronetix design will have its PHY available at address 0x1 and
Embest design at 0x7.
By defining both phys we're letting the phy core detect the one actually
available on the MDIO bus.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Tested-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Commit ff795d614b ("ASoC: ab8500: Convert register I/O to regmap")
initially converted the ab8500 CODEC driver to use regmap rather than
legacy ASoC IO. This was reverted though in commit 63e6d43bf8 ("ASoC:
ab8500: Revert to using custom I/O functions") since the inital conversion
was not working properly. This was presumebly because the SOC_SINGLE_XR_SX
controls, which are used by this driver, did not properly support regmap at
that point. This has since been fixed in commit 6137a5ca32 ("ASoC: Prepare
SOC_SINGLE_XR_SX controls for regmap"). So revert back to regmap again.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
device_add() expects that any memory allocated via devm_* API is only
done in the device's probe function.
Fix below boot warning:
WARNING: CPU: 1 PID: 1 at drivers/base/dd.c:286 driver_probe_device+0x2b4/0x2f4()
Modules linked in:
CPU: 1 PID: 1 Comm: swapper/0 Not tainted 3.16.0-10474-g835c90b-dirty #160
[<c0016364>] (unwind_backtrace) from [<c001251c>] (show_stack+0x20/0x24)
[<c001251c>] (show_stack) from [<c04eaefc>] (dump_stack+0x7c/0x98)
[<c04eaefc>] (dump_stack) from [<c0023d4c>] (warn_slowpath_common+0x78/0x9c)
[<c0023d4c>] (warn_slowpath_common) from [<c0023d9c>] (warn_slowpath_null+0x2c/0x34)
[<c0023d9c>] (warn_slowpath_null) from [<c0302c60>] (driver_probe_device+0x2b4/0x2f4)
[<c0302c60>] (driver_probe_device) from [<c0302d90>] (__device_attach+0x50/0x54)
[<c0302d90>] (__device_attach) from [<c0300e60>] (bus_for_each_drv+0x54/0x9c)
[<c0300e60>] (bus_for_each_drv) from [<c0302958>] (device_attach+0x84/0x90)
[<c0302958>] (device_attach) from [<c0301f10>] (bus_probe_device+0x94/0xb8)
[<c0301f10>] (bus_probe_device) from [<c03000c0>] (device_add+0x434/0x4fc)
[<c03000c0>] (device_add) from [<c0342dd4>] (spi_add_device+0x98/0x164)
[<c0342dd4>] (spi_add_device) from [<c03444a4>] (spi_register_master+0x598/0x768)
[<c03444a4>] (spi_register_master) from [<c03446b4>] (devm_spi_register_master+0x40/0x80)
[<c03446b4>] (devm_spi_register_master) from [<c0346214>] (dw_spi_add_host+0x1a8/0x258)
[<c0346214>] (dw_spi_add_host) from [<c0346920>] (dw_spi_mmio_probe+0x1d4/0x294)
[<c0346920>] (dw_spi_mmio_probe) from [<c0304560>] (platform_drv_probe+0x3c/0x6c)
[<c0304560>] (platform_drv_probe) from [<c0302a98>] (driver_probe_device+0xec/0x2f4)
[<c0302a98>] (driver_probe_device) from [<c0302d3c>] (__driver_attach+0x9c/0xa0)
[<c0302d3c>] (__driver_attach) from [<c0300f0c>] (bus_for_each_dev+0x64/0x98)
[<c0300f0c>] (bus_for_each_dev) from [<c0302518>] (driver_attach+0x2c/0x30)
[<c0302518>] (driver_attach) from [<c0302134>] (bus_add_driver+0xdc/0x1f4)
[<c0302134>] (bus_add_driver) from [<c03035c8>] (driver_register+0x88/0x104)
[<c03035c8>] (driver_register) from [<c030445c>] (__platform_driver_register+0x58/0x6c)
[<c030445c>] (__platform_driver_register) from [<c0700f00>] (dw_spi_mmio_driver_init+0x18/0x20)
[<c0700f00>] (dw_spi_mmio_driver_init) from [<c0008914>] (do_one_initcall+0x90/0x1d4)
[<c0008914>] (do_one_initcall) from [<c06d7d90>] (kernel_init_freeable+0x178/0x248)
[<c06d7d90>] (kernel_init_freeable) from [<c04e687c>] (kernel_init+0x18/0xfc)
[<c04e687c>] (kernel_init) from [<c000ecd8>] (ret_from_fork+0x14/0x20)
Reported-by: Thor Thayer <tthayer@opensource.altera.com>
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
DAI links's cpu_of_node's and codec_of_node's refcounts shouldn't
be decremented immediately at the end of the probe() fucntion.
Because we will still use them before the audio card is removed.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The wakeup status is read from Shutdown Status Register and not the
SHDW_CR which is the one at address 0.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
MACH_AT91 doesn't exist so we can't "depend" on it. Fix the typo
by using the proper ARCH_AT91 config option.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
After the for_each_matching_node loop, we end up with a null value for np. Then,
of_match_node() is not matching anything and we can't register the standby
function and "ramc no standby function available" is printed.
Fix that by selecting the first available standby function. For now,
at91_pm_set_standby doesn't support multiple different standby functions and no
existing SoCs have different RAM controllers.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
If split page table lock for PTE tables is enabled (CONFIG_SPLIT_PTLOCK_CPUS
<=NR_CPUS) pgtable_page_ctor() leads to non-atomic allocation for ptlock with
a spinlock held, resulting in:
------------[ cut here ]------------
WARNING: CPU: 0 PID: 466 at kernel/locking/lockdep.c:2742 lockdep_trace_alloc+0xd8/0xf4()
DEBUG_LOCKS_WARN_ON(irqs_disabled_flags(flags))
Modules linked in:
CPU: 0 PID: 466 Comm: dma0chan0-copy0 Not tainted 3.16.0-3d47efb-clean-pl330-dma_test-ve-a15-a32-slr-m
c-on-3+ #55
[<80014748>] (unwind_backtrace) from [<80011640>] (show_stack+0x10/0x14)
[<80011640>] (show_stack) from [<802bf864>] (dump_stack+0x80/0xb4)
[<802bf864>] (dump_stack) from [<8002385c>] (warn_slowpath_common+0x64/0x88)
[<8002385c>] (warn_slowpath_common) from [<80023914>] (warn_slowpath_fmt+0x30/0x40)
[<80023914>] (warn_slowpath_fmt) from [<8005d818>] (lockdep_trace_alloc+0xd8/0xf4)
[<8005d818>] (lockdep_trace_alloc) from [<800d3d78>] (kmem_cache_alloc+0x24/0x144)
[<800d3d78>] (kmem_cache_alloc) from [<800bfae4>] (ptlock_alloc+0x18/0x2c)
[<800bfae4>] (ptlock_alloc) from [<802b1ec0>] (arm_smmu_handle_mapping+0x4c0/0x690)
[<802b1ec0>] (arm_smmu_handle_mapping) from [<802b0cd8>] (iommu_map+0xe0/0x148)
[<802b0cd8>] (iommu_map) from [<80019098>] (arm_coherent_iommu_map_page+0x160/0x278)
[<80019098>] (arm_coherent_iommu_map_page) from [<801f4d78>] (dmatest_func+0x60c/0x1098)
[<801f4d78>] (dmatest_func) from [<8003f8ac>] (kthread+0xcc/0xe8)
[<8003f8ac>] (kthread) from [<8000e868>] (ret_from_fork+0x14/0x2c)
---[ end trace ce0d27e6f434acf8 ]--
Split page tables lock is not used in the driver. In fact, page tables are
guarded with domain lock, so remove calls to pgtable_page_{c,d}tor().
Cc: <stable@vger.kernel.org>
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Stage-1 context banks do not have the SMMU_CBn_TCR[SL0] field since it
is only applicable to stage-2 context banks.
This patch ensures that we don't set the reserved TCR bits for stage-1
translations.
Cc: <stable@vger.kernel.org>
Signed-off-by: Olav Haugan <ohaugan@codeaurora.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
request_irq shouldn't be called from atomic context since it might
sleep, but we're calling it with a spinlock held, resulting in:
[ 9.172202] BUG: sleeping function called from invalid context at kernel/mm/slub.c:926
[ 9.182989] in_atomic(): 1, irqs_disabled(): 128, pid: 1, name: swapper/0
[ 9.189762] CPU: 1 PID: 1 Comm: swapper/0 Tainted: G W 3.10.40-gbc1b510b-38437-g55831d3bd9-dirty #97
[ 9.199757] [<c020c448>] (unwind_backtrace+0x0/0x11c) from [<c02097d0>] (show_stack+0x10/0x14)
[ 9.208346] [<c02097d0>] (show_stack+0x10/0x14) from [<c0301d74>] (kmem_cache_alloc_trace+0x3c/0x210)
[ 9.217543] [<c0301d74>] (kmem_cache_alloc_trace+0x3c/0x210) from [<c0276a48>] (request_threaded_irq+0x88/0x11c)
[ 9.227702] [<c0276a48>] (request_threaded_irq+0x88/0x11c) from [<c0931ca4>] (arm_smmu_attach_dev+0x188/0x858)
[ 9.237686] [<c0931ca4>] (arm_smmu_attach_dev+0x188/0x858) from [<c0212cd8>] (arm_iommu_attach_device+0x18/0xd0)
[ 9.247837] [<c0212cd8>] (arm_iommu_attach_device+0x18/0xd0) from [<c093314c>] (arm_smmu_test_probe+0x68/0xd4)
[ 9.257823] [<c093314c>] (arm_smmu_test_probe+0x68/0xd4) from [<c05aadd0>] (driver_probe_device+0x12c/0x330)
[ 9.267629] [<c05aadd0>] (driver_probe_device+0x12c/0x330) from [<c05ab080>] (__driver_attach+0x68/0x8c)
[ 9.277090] [<c05ab080>] (__driver_attach+0x68/0x8c) from [<c05a92d4>] (bus_for_each_dev+0x70/0x84)
[ 9.286118] [<c05a92d4>] (bus_for_each_dev+0x70/0x84) from [<c05aa3b0>] (bus_add_driver+0x100/0x244)
[ 9.295233] [<c05aa3b0>] (bus_add_driver+0x100/0x244) from [<c05ab5d0>] (driver_register+0x9c/0x124)
[ 9.304347] [<c05ab5d0>] (driver_register+0x9c/0x124) from [<c0933088>] (arm_smmu_test_init+0x14/0x38)
[ 9.313635] [<c0933088>] (arm_smmu_test_init+0x14/0x38) from [<c0200618>] (do_one_initcall+0xb8/0x160)
[ 9.322926] [<c0200618>] (do_one_initcall+0xb8/0x160) from [<c1200b7c>] (kernel_init_freeable+0x108/0x1cc)
[ 9.332564] [<c1200b7c>] (kernel_init_freeable+0x108/0x1cc) from [<c0b924b0>] (kernel_init+0xc/0xe4)
[ 9.341675] [<c0b924b0>] (kernel_init+0xc/0xe4) from [<c0205e38>] (ret_from_fork+0x14/0x3c)
Fix this by moving the request_irq out of the critical section. This
should be okay since smmu_domain->smmu is still being protected by the
critical section. Also, we still don't program the Stream Match Register
until after registering our interrupt handler so we shouldn't be missing
any interrupts.
Cc: <stable@vger.kernel.org>
Signed-off-by: Mitchel Humpherys <mitchelh@codeaurora.org>
[will: code cleanup and fixed request_irq token parameter]
Signed-off-by: Will Deacon <will.deacon@arm.com>
The 'big-endian-data' property is originally used to indicate whether the
LSB firstly or MSB firstly will be transmitted to the CODEC or received
from the CODEC, and there has nothing relation to the memory data.
Generally, if the audio data in big endian format, which will be using the
bytes reversion, Here this can only be used to bits reversion.
So using the 'lsb-first' instead of 'big-endian-data' can make the code
to be readable easier and more easy to understand what this property is
used to do.
This property used for configuring whether the LSB or the MSB is transmitted
first for the fifo data.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>