This patch set HSE_RTC clock frequency to 1 MHz, as the clock supplied to
the RTC must be 1 MHz.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
This patch include auxiliary clock definition (clocks which are not derived
from system clock.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
This patch adds an external I2S clock in the DT.
The I2S clock could be derived from an external I2S clock or by I2S pll.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Enable analog to digital converter on stm32f429i-eval board.
It has on-board potentimeter wired to ADC3 in8 analog pin and
uses fixed regulator to provide reference voltage.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
This patch adds USART3 pin configuration on PB10/PA11 pins
for STM32F469I-DISCO board.
Signed-off-by: Bruno Herrera <bruherrera@gmail.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
This patch fix memory size to support 16MB of external SDRAM.
Signed-off-by: Bruno Herrera <bruherrera@gmail.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
The warn on is a bit too much, we will anyway set the dma mask if not set
previously.
The main reason for this fix is that 4.10-rc1 has a dwc3 change that
pass a parent sysdev dev pointer instead of setting the dma mask of
its xhci platform device. xhci platform driver can then get more
attributes from the sysdev than just the dma mask.
The usb core and xhci changes are not yet in 4.10, and a fix like
this was preferred instead of taking those big changes this late in
the rc-cycle.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As part of cleaning up architecture specific code, define APIs
to manage interrupt state.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As part of cleaning up architecture specific code, define an API
to retrieve the virtual procesor index.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As part of cleaning up architecture specific code, define APIs
to manipulate the interrupt controller state.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As part of cleaning up architecture specific code, define APIs
to manipulate the event page.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As part of cleaning up architecture specific code, define APIs
to manipulate the message page.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The version variable while it is initialized is not used;
get rid of it.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As part of the effort to interact with Hyper-V in an instruction set
architecture independent way, use the new API to get the current
tick.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move the relevant code that programs the hypervisor to an architecture
specific file.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As part of the effort to separate out architecture specific code, move the
code for signaling end of message.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As part of the effort to separate out architecture specific code, move the
check for detecting if the hypercall page is setup.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As part of the effort to separate out architecture specific code, move the
crash notification function.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As part of the effort to separate out architecture specific code,
extract hypervisor version information in an architecture specific
file.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As part of the effort to separate out architecture specific code,
consolidate all Hyper-V specific clocksource code to an architecture
specific code.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In xen_swiotlb_map_page and xen_swiotlb_map_sg_attrs, if the original
page is not suitable, we swap it for another page from the swiotlb
pool.
In these cases, we don't update the previously calculated dma address
for the page before calling xen_dma_map_page. Thus, we end up calling
xen_dma_map_page passing the wrong dev_addr, resulting in
xen_dma_map_page mistakenly assuming that the page is foreign when it is
local.
Fix the bug by updating dev_addr appropriately.
This change has no effect on x86, because xen_dma_map_page is a stub
there.
Signed-off-by: Stefano Stabellini <sstabellini@kernel.org>
Signed-off-by: Pooya Keshavarzi <Pooya.Keshavarzi@de.bosch.com>
Tested-by: Pooya Keshavarzi <Pooya.Keshavarzi@de.bosch.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
8250 UART DMA support was marked broken by default as it was not
possible to pause ongoing RX DMA transfer. Now that both SDMA and
EDMA can support pause operation for RX DMA transactions, don't set
rx_dma_broken to true by default. With this patch 8250_omap driver will
use DMA by default.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
UART uses as EDMA as dma engine on AM437x SoC and therefore, requires
OMAP_DMA_TX_KICK quirk just like AM33xx. So, enable OMAP_DMA_TX_KICK
quirk for AM437x platform as well. While at that, drop use of
of_machine_is_compatible() and instead pass quirks via device data.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is possible that DMA transfer is already complete but, completion
handler is yet to be called, when dmaengine_pause() is called in case of
error condition(like break/rx timeout). This leads to dmaengine_pause()
API to return EINVAL (as descriptor is already NULL) causing
rx_dma_broken flag to be set and effectively disabling RX DMA.
Fix this by calling dmaengine_pause() only when transfer is in progress.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mei_cl_set_disconnected is used only in client.c,
so make it local to the file and mark static.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mei_io_list_flush is used only in client.c
so make it local to the file and mark static.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the following warnings:
Block comments should align the * on each line
Signed-off-by: Abdul Rauf <abdulraufmujahid@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With codec read sometimes the pin_sense shows invalid monitor present
and eld_valid. Currently driver polls for few times to get the valid
eld data.
To avoid the latency, Instead of reading ELD from codec, read it
directly from the display driver using audio component framework.
and removed the unused direct codec helper functions.
Signed-off-by: Sandeep Tayal <sandeepx.tayal@intel.com>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Ls2088a is new introduced arm-based soc with sata support with
following features:
1. Complies with the serial ATA 3.0 specification and the AHCI 1.3.1
specification
2. Contains a high-speed descriptor-based DMA controller
3. Supports the following:
a. Speeds of 1.5 Gb/s (first-generation SATA), 3 Gb/s
(second-generation SATA), and 6 Gb/s (third-generation SATA)
b. FIS-based switching
c. Native command queuing (NCQ) commands
d. Port multiplier operation
e. Asynchronous notification
f. SATA BIST mode
Signed-off-by: Tang Yuantian <yuantian.tang@nxp.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
For ls1021a, and armv8 chasis 2 socs, sata ecc must be disabled.
If ecc register is not found in sata node in dts, report error.
This is a chip erratum described as bellow:
The Read DMA operations get early termination indication from the
controller. This issue is observed as CRC error in the status registers.
The issue is due to address collision at address 0 in the dual port
memory. The read is a dummy read to flush out the header, but due to
collision the controller logs the mbit error reported by the ECC check
logic. This results in the early termination of the Read DMA operation
by the controller. The issue happens to all the interface
speeds(GEN1/2/3) for all the products.
Workaround:
Disable ECC feature on those platforms.
Signed-off-by: Tang Yuantian <yuantian.tang@nxp.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Enable DMA coherence in SATA controller on condition that
dma-coherent property exists in sata node in DTS.
Signed-off-by: Tang Yuantian <yuantian.tang@nxp.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Add pin configuration support for Gyro-ADC, named ADI on r8a7791 SoC.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Tested-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
commit 66feeec9322132689d42723df2537d60f96f8e44
"RFC: ASoC: dapm: handle probe deferrals"
forgot a to update some two sites where the call
was used. The static codechecks quickly found them.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: 66feeec93221 ("RFC: ASoC: dapm: handle probe deferrals")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
It will be used in following patch to expand or collapse only the
current browser entry.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1484904032-11040-2-git-send-email-jolsa@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
The H3 SoC uses the same SPDIF block as found in earlier SoCs, but its
TXFIFO is mapped to another address.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The H3 SoC uses the same SPDIF block as found in earlier SoCs, but the
transmit fifo is at a different address.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
commit 5f222a292 ("ASoC: rsnd: use for_each_rsnd_mod_xxx() ...")
modifies rsnd_dai_call() to use for_each_rsnd_mod_arrays().
Current rsnd is incrementing iterator in rsnd_mod_next(),
but the iterator will indicate +1 position in for_each loop in
this case. Incremental position should be inside for()
Reported-by: Hoan Nguyen An <na-hoan@jinso.co.jp>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This enables the iio subsystem. This will be used by LEGO MINDSTORMS EV3,
which has an ADS7957 chip.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
This adds a device tree definition file for LEGO MINDSTORMS EV3.
What is working:
* Pin muxing
* Pinconf
* GPIOs
* MicroSD card reader
* UART on input port 1
* Buttons
* LEDs
* Poweroff/reset
* Flash memory
* EEPROM
* USB host port
* USB peripheral port
What is not working/to be added later:
* Speaker - have patch submitted to get pwm-beeper working - maybe someday
it will have a real sound driver that uses PRU
* A/DC chip - have driver submitted and accepted - waiting for ack on
device tree bindings
* Display - waiting for "simple DRM" to be mainlined
* Bluetooth - needs new driver for sequencing power/enable/clock
* Input and output ports - need some sort of new phy or extcon driver as
well as PRU UART and PRU I2C drivers
* Battery indication - needs new power supply driver
Note on flash partitions:
These partitions are based on the official EV3 firmware from LEGO. It is
expected that most users of the mainline kernel on EV3 will be booting from
an SD card while retaining the official firmware in the flash memory.
Furthermore, the official firmware uses an ancient U-Boot (2009) that has
no device tree support. So, it makes sense to have this partition table in
the EV3 device tree file. In the unlikely case that anyone does create
their own firmware image with different partitioning, they can use a modern
U-Boot in their own firmware image that modifies the device tree with the
custom partitions.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
This adds "microchip,24c128" to the list of compatible strings for i2c
eeproms.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
This adds the board level device tree specification for LEGO MINDSTORMS EV3
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Add a vendor prefix for LEGO Systems A/S
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Reading both fault and status registers and logging any fault should
take priority over handling status register update.
Fix by moving the status handling to later in interrupt routine.
Fixes: d7bf353fd0 ("bq24190_charger: Add support for TI BQ24190 Battery Charger")
Signed-off-by: Liam Breck <kernel@networkimprov.net>
Acked-by: Mark Greer <mgreer@animalcreek.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Caching the fault register after a single I2C read may not keep an accurate
value.
Fix by doing two reads in irq_handle_thread() and using the cached value
elsewhere. If a safety timer fault later clears itself, we apparently don't get
an interrupt (INT), however other interrupts would refresh the register cache.
From the data sheet: "When a fault occurs, the charger device sends out INT
and keeps the fault state in REG09 until the host reads the fault register.
Before the host reads REG09 and all the faults are cleared, the charger
device would not send any INT upon new faults. In order to read the
current fault status, the host has to read REG09 two times consecutively.
The 1st reads fault register status from the last read [1] and the 2nd reads
the current fault register status."
[1] presumably a typo; should be "last fault"
Fixes: d7bf353fd0 ("bq24190_charger: Add support for TI BQ24190 Battery Charger")
Signed-off-by: Liam Breck <kernel@networkimprov.net>
Acked-by: Mark Greer <mgreer@animalcreek.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
We wrongly get uevents for bq24190-charger and bq24190-battery on every
register change.
Fix by checking the association with charger and battery before
emitting uevent(s).
Fixes: d7bf353fd0 ("bq24190_charger: Add support for TI BQ24190 Battery Charger")
Signed-off-by: Liam Breck <kernel@networkimprov.net>
Acked-by: Mark Greer <mgreer@animalcreek.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The device specific data is not fully initialized on
request_threaded_irq(). This may cause a crash when the IRQ handler
tries to reference them.
Fix the issue by installing IRQ handler at the end of the probe.
Fixes: d7bf353fd0 ("bq24190_charger: Add support for TI BQ24190 Battery Charger")
Signed-off-by: Liam Breck <kernel@networkimprov.net>
Acked-by: Mark Greer <mgreer@animalcreek.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
