pm_resume() does a register_reset() which clears charger host mode.
Fix by calling set_mode_host() after the reset.
Fixes: d7bf353fd0 ("bq24190_charger: Add support for TI BQ24190 Battery Charger")
Signed-off-by: Liam Breck <kernel@networkimprov.net>
Acked-by: Mark Greer <mgreer@animalcreek.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The interrupt signal is TRIGGER_FALLING. This is is specified in the
data sheet PIN FUNCTIONS: "The INT pin sends active low, 256us
pulse to host to report charger device status and fault."
Also the direction can be seen in the data sheet Figure 37 "BQ24190
with D+/D- Detection and USB On-The-Go (OTG)" which shows a 10k
pull-up resistor installed for the sample configurations.
Fixes: d7bf353fd0 ("bq24190_charger: Add support for TI BQ24190 Battery Charger")
Signed-off-by: Liam Breck <kernel@networkimprov.net>
Acked-by: Mark Greer <mgreer@animalcreek.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
udf_fill_super() used udf_parse_options() to flag UDF_FLAG_BLOCKSIZE_SET
when blocksize was specified otherwise used 512 bytes
(bdev_logical_block_size) and 2048 bytes (UDF_DEFAULT_BLOCKSIZE)
IOW both 1024 and 4096 specifications were required or resulted in
"mount: wrong fs type, bad option, bad superblock on /dev/loop1"
This patch loops through different block values but also updates
udf_load_vrs() to return -EINVAL instead of 0 when udf_check_vsd()
fails (and uopt->novrs = 0).
The later being the reason for the RFC; we have that case when mounting
a 4kb blocksize against other values but maybe VRS is not mandatory
there ?
Tested with 512, 1024, 2048 and 4096 blocksize
Reported-by: Jan Kara <jack@suse.com>
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Jan Kara <jack@suse.cz>
These drivers use a set of complicated macros to extract and insert
information for the RX and TX descriptors. Driver rtl8192cu had a
different set than was used for the PCI-based drivers. To simplify
the code, rtl8192cu is switched to use the common version. In the
process, two errors in those common macros were found and fixed.
Besides simplifying the code, there is an additional benefit. We have
no BE hardware to test the PCI driver, but using the common macros
provides an additional test for the validity of many endian-sensitive
operations.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This driver requires a checksum for the descriptors so that the wifi
chip is assured that the USB transmission was correct. These entries
are little-endian, but the driver was always using cpu order in the
calculation. As a result, the driver failed on BE hardware.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The firmware is read from disk as a little-endian byte string. The code
that loads the firmware into the device transfers it as 4-byte quantities.
The routines that write multi-byte quantities on BE hardware assume that
the data are in CPU order, and automatically do the conversion to the LE
order required by the device. As a result, the firmware is transmitted
incorrectly. Rather than do multiple byte swaps on the data, the download
routine is revised to transmit bytes rather than dwords. Although the
number of I/O operations is increased, the firmware is not often loaded.
All drivers have the same bug, and use essentially the same code to
download firmware. These routines have been moved into rtlwifi.
Some CamelCase variables have been renamed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As the kernel provides access to module parameters through entries in
/sys/module/<driver>/parameters/, there is no need for a private
interface. Thus the existing code for setting the debug level is
removed.
Reported-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The debugging macros contain a parameter COMP_XX that could be used as a
mask; however, the code turns all these various bits on at the same time.
This change implements them as a proper mask, and adds module parameters
to set the mask at load time.
The current name "debug" for the debug level has been changed to
"debug_level" to better differentiate it from "debug_mask".
The debug routines have also been changed to interrogate the structure
that is loaded at entry time. As a result, the structure rtl_debug is no
longer needed, and all references to it are deleted.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
These two debugging formss implement debugging using rather complicated
macro constructions. These are replaced with compiled code that is easier
to understand.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This intends to make init/attach process slightly easier to follow.
What driver was doing in brcmf_bus_start wasn't bus specific at all and
function brcmf_bus_stop wasn't undoing things done there. This function
is supposed to be called by bus specific code when the bus is ready.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Driver used to call brcmf_bus_detach only from one place and it already
contained a check for drvr not being NULL. We can get rid of this extra
function, call brcmf_bus_stop directly and simplify the code.
There also isn't brcmf_bus_attach function which one could expect so it
looks more consistent this way.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Function brcmf_c_set_joinpref_default is in common.c, so move it to the
related header.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Functions brcmf_c_prec_enq and brcmf_sdio_init don't exist so we
really don't need their declarations. Function brcmf_parse_tlvs is used
in cfg80211.c only so make it static and drop from header as well.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
brcmf_sdio_fromevntchan() was being called on the the data frame
rather than the software header, causing some frames to be
mischaracterized as on the event channel rather than the data channel.
This fixes a major performance regression (due to dropped packets). With
this patch the download speed jumped from 1Mbit/s back up to 40MBit/s due
to the sheer amount of packets being incorrectly processed.
Fixes: c56caa9db8 ("brcmfmac: screening firmware event packet")
Signed-off-by: Gavin Li <git@thegavinli.com>
Cc: <stable@vger.kernel.org> # 4.7+
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
[kvalo@codeaurora.org: improve commit logs based on email discussion]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
These IDs originate from the vendor driver
Signed-off-by: Axel Köllhofer <AxelKoellhofer@web.de>
Signed-off-by: Jes Sorensen <Jes.Sorensen@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This was tested by David Patiño.
Reported-by: David Patiño <davidpatino82@gmail.com>
Signed-off-by: Axel Köllhofer <AxelKoellhofer@web.de>
Signed-off-by: Jes Sorensen <Jes.Sorensen@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Device reported as working fine, so tell the driver not to warn about
it being untested.
Reported-by: Aex Aey <aexaey@gmail.com>
Signed-off-by: Jes Sorensen <Jes.Sorensen@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
BCM43455 is a more recent revision of the BCM4345. Some of the BCM43455
got a dedicated SDIO device ID which is currently not supported by
brcmfmac.
Adding the new sdio_device_id to brcmfmac is enough to get the BCM43455
supported because the chip itself is already supported (due to BCM4345
support in the driver).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Tested-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Marvell folks tell me this is a debugging event that the driver doesn't
need to handle, but on 8997 w/ firmware 16.68.1.p97, I see several of
these sorts of messages at (for instance) boot time:
[ 13.825848] mwifiex_pcie 0000:01:00.0: event: unknown event id: 0x63
[ 14.838561] mwifiex_pcie 0000:01:00.0: event: unknown event id: 0x63
[ 14.850397] mwifiex_pcie 0000:01:00.0: event: unknown event id: 0x63
[ 32.529923] mwifiex_pcie 0000:01:00.0: event: unknown event id: 0x63
Let's handle this "event" with a much lower verbosity.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In mwifiex_delay_for_sleep_cookie(), we're looping and waiting for the
PCIe endpoint to write a magic value back to memory, to signal that it
has finished going to sleep. We're not letting the compiler know that
this might change underneath our feet though. Let's do that, for good
hygiene.
I'm not aware of this fixing any concrete problems. I also give no
guarantee that this loop is actually correct in any other way, but at
least this looks like an improvement to me.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The following sequence occurs when using IEEE power-save on 8997:
(a) driver sees SLEEP event
(b) driver issues SLEEP CONFIRM
(c) driver recevies CMD interrupt; within the interrupt processing loop,
we do (d) and (e):
(d) wait for FW sleep cookie (and often time out; it takes a while), FW
is putting card into low power mode
(e) re-check PCIE_HOST_INT_STATUS register; quit loop with 0 value
But at (e), no one actually signaled an interrupt (i.e., we didn't check
adapter->int_status). And what's more, because the card is going to
sleep, this register read appears to take a very long time in some cases
-- 3 milliseconds in my case!
Now, I propose that (e) is completely unnecessary. If there were any
additional interrupts signaled after the start of this loop, then the
interrupt handler would have set adapter->int_status to non-zero and
queued more work for the main loop -- and we'd catch it on the next
iteration of the main loop.
So this patch drops all the looping/re-reading of PCIE_HOST_INT_STATUS,
which avoids the problematic (and slow) register read in step (e).
Incidentally, this is a very similar issue to the one fixed in commit
ec815dd2a5 ("mwifiex: prevent register accesses after host is
sleeping"), except that the register read is just very slow instead of
fatal in this case.
Tested on 8997 in both MSI and (though not technically supported at the
moment) MSI-X mode.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Depending on system factors (e.g., the PCIe link PM state), the first
read to wake up the Wifi firmware can take a long time. There is no
reason to use a (blocking, non-posted) read at this point, so let's just
use a write instead. Write vs. read doesn't matter functionality-wise --
it's just a dummy operation. But let's make sure to re-write with the
correct "ready" signature, since we check for that in other parts of the
driver.
This has been shown to decrease the time spent blocking in this function
on RK3399.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The *_get_optional_* functions weren't really optional so this patch
makes them really optional.
These *_get_optional_* functions will now return NULL instead of an error
if no matching reset phandle is found in the DT, and all the
reset_control_* functions now accept NULL rstc pointers.
Signed-off-by: Ramiro Oliveira <Ramiro.Oliveira@synopsys.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Since the new parameter being added is going to be a bool this patch
changes the shared flag from int to bool to match the new parameter.
Signed-off-by: Ramiro Oliveira <Ramiro.Oliveira@synopsys.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
The LD11 SoC is equipped with not only MIO-reset but also SD-reset
for controlling RST_n pin of the eMMC device.
Update the binding document and remove unneeded "." from each line
in itemization.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Add the zx2967 reset controller driver as maintained by ARM ZTE
architecture maintainers, as they're parts of the core IP.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
When we reach the user's RPS limits, stop requesting an adjustment. Even
though we will clamp the requested frequency later, we rely on interrupt
masking to disable further adjustments in the same direction. Even
though it is unlikely (one scenario is a bug in the driver, another is
careful manipulation through the uAPI) if we keep exponentially
increasing the adjustment value, it will wrap and cause a negative
adjustment.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1484884104-28134-2-git-send-email-sagar.a.kamble@intel.com
There is no need to choose a random initcall level for certainly
architecture dependent code.
Move watchdog registration to arch_initcall() from rootfs_initcall().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: http://lkml.kernel.org/r/20170119192425.189899-5-andriy.shevchenko@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Legacy RTC requires interrupt line 8 to be dedicated for it. On
Intel MID platforms the legacy PIC is absent and in order to make RTC
work we need to allocate interrupt separately.
Current solution brought by commit de1c2540aa does it in a wrong place,
and since it's done unconditionally for all x86 devices, some of them,
e.g. PNP based, might get it wrong because they execute the MID specific
code due to x86_platform.legacy.rtc flag being set.
Move intel_mid_legacy_rtc_init() to its own module and call it before x86 RTC
CMOS initialization.
Fixes: de1c2540aa ("x86/platform/intel-mid: Enable RTC on Intel Merrifield")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: "Luis R . Rodriguez" <mcgrof@kernel.org>
Link: http://lkml.kernel.org/r/20170119192425.189899-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
mp_map_gsi_to_irq() in some cases might return legacy -1, which would be
wrongly interpreted as -EPERM.
Correct those cases to return proper error code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: http://lkml.kernel.org/r/20170119192425.189899-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Since sem->count had been changed to a atomic_long_t type, it is no
longer necessary to use the atomic_long_t cast anymore. So remove them.
Signed-off-by: Waiman Long <longman@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-arch@vger.kernel.org
Link: http://lkml.kernel.org/r/1484836312-6656-1-git-send-email-longman@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The CI_HDRC_CONTROLLER_STOPPED_EVENT may want to call sleeping
APIs similar to how _gadget_stop_activity() may. Let's drop the
lock across the event so that glue drivers can make sleeping
calls.
Cc: Peter Chen <peter.chen@nxp.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
If something fails in ci_hdrc_add_device() due to probe defer, we
shouldn't print an error message. Be silent in this case as we'll
try probe again later.
Acked-by: Peter Chen <peter.chen@nxp.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
The ULPI phy on qcom platforms needs to be initialized and
powered on after a USB reset and before we toggle the run/stop
bit. Otherwise, the phy locks up and doesn't work properly. Hook
the phy initialization into the RESET event and the phy power off
into the STOPPED event.
Acked-by: Peter Chen <peter.chen@nxp.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
The MSM chipidea wrapper has two bits that are used to reset the
first or second phy. Add support for these bits via the reset
controller framework, so that phy drivers can reset their
hardware at the right time during initialization.
Acked-by: Peter Chen <peter.chen@nxp.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
If two devices are probed with this same driver, they'll share
the same platform data structure, while the chipidea core layer
writes and modifies it. This can lead to interesting results
especially if one device is an OTG type chipidea controller and
another is a host. Let's create a copy of this structure per each
device instance so that odd things don't happen.
Acked-by: Peter Chen <peter.chen@nxp.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
When the RESET bit is set in the USBCMD register it resets quite
a few of the wrapper's registers to their reset state. This
includes the GENCONFIG and GENCONFIG2 registers. Currently this
is done by the usb phy and ehci-msm drivers writing into the
controller wrapper's MMIO address space. Let's consolidate the
register writes into the wrapper driver instead so that we
clearly split the wrapper from the phys.
Acked-by: Peter Chen <peter.chen@nxp.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
We need to pick the correct phy at runtime based on how the SoC
has been wired onto the board. If the secondary phy is used, take
it out of reset and mux over to it by writing into the TCSR
register. Make sure to do this on reset too, because this
register is reset to the default value (primary phy) after the
RESET bit is set in USBCMD.
Acked-by: Peter Chen <peter.chen@nxp.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
The msm chipidea controller uses two main clks, an AHB clk to
read/write the MMIO registers and a core clk called the system
clk that drives the controller itself. Add support for these clks
as they're required in all designs.
Also add support for an optional third clk that we need to turn
on to reset the controller and wrapper logic and other
"housekeeping" things. This clk was removed in later revisions of
the hardware because the reset methodology no longer required
clks to be enabled to propagate resets.
Acked-by: Peter Chen <peter.chen@nxp.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
The MSM_USB_BASE macro trick is not very clear, and we're using
it for only one register write so let's just move to using
hw_write_id_reg() and passing the ci pointer instead. That
clearly shows what offset we're using and avoids needing to
include the msm_hsusb_hw.h file when we're going to delete that
file soon.
Acked-by: Peter Chen <peter.chen@nxp.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
The core framework already handles setting this parameter with a
platform quirk. Add the appropriate flag so that we always set
AHBBURST to 0. Technically DT should be doing this, but we always
do it for msm chipidea devices so setting the flag in the driver
works just as well. If the burst needs to be anything besides 0,
we expect the 'ahb-burst-config' dts property to be present.
Acked-by: Peter Chen <peter.chen@nxp.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
We're not properly marking the glue layer/wrapper device as
runtime active, so runtime PM believes that the hardware state is
inactive when we call pm_runtime_enable() in this driver. This
causes a problem when the glue layer has a power domain
associated with it, because runtime PM will go and disable the
power domain to match the 'inactive' state of the device. Let's
mark the device as active so that runtime PM doesn't improperly
power down this device when it's actually active.
Acked-by: Peter Chen <peter.chen@nxp.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
At some situations, the vbus may already be there before starting
gadget. So we need to check vbus event after switching to gadget in
order to handle missing vbus event. The typical use cases are plugging
vbus cable before driver load or the vbus has already been there
after stopping host but before starting gadget.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Tested-by: Stephen Boyd <stephen.boyd@linaro.org>
Reported-by: Stephen Boyd <stephen.boyd@linaro.org>
DECON_TV requires STANDALONE_UPDATE after output enabling, otherwise it does
not start. This change is neutral for DECON.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
