SoC family such as DRA7 family of processors have, in addition
to the regular muxing of pins (as done by pinctrl-single), a separate
hardware module called IODelay which is also expected to be configured.
The "IODelay" module has it's own register space that is independent
of the control module and the padconf register area.
With recent changes to the pinctrl framework, we can now support
this hardware with a reasonably minimal driver by using #pinctrl-cells,
GENERIC_PINCTRL_GROUPS and GENERIC_PINMUX_FUNCTIONS.
It is advocated strongly in TI's official documentation considering
the existing design of the DRA7 family of processors during mux or
IODelay reconfiguration, there is a potential for a significant glitch
which may cause functional impairment to certain hardware. It is
hence recommended to do as little of muxing as absolutely necessary
without I/O isolation (which can only be done in initial stages of
bootloader).
NOTE: with the system wide I/O isolation scheme present in DRA7 SoC
family, it is not reasonable to do stop all I/O operations for every
such pad configuration scheme. So, we will let it glitch when used in
this mode.
Even with the above limitation, certain functionality such as MMC has
mandatory need for IODelay reconfiguration requirements, depending on
speed of transfer. In these cases, with careful examination of usecase
involved, the expected glitch can be controlled such that it does not
impact functionality.
In short, IODelay module support as a padconf driver being introduced
here is not expected to do SoC wide I/O Isolation and is meant for
a limited subset of IODelay configuration requirements that need to
be dynamic and whose glitchy behavior will not cause functionality
failure for that interface.
IMPORTANT NOTE: we take the approach of keeping LOCK_BITs cleared
to 0x0 at all times, even when configuring Manual IO Timing Modes.
This is done by eliminating the LOCK_BIT=1 setting from Step
of the Manual IO timing Mode configuration procedure. This option
leaves the CFG_* registers unprotected from unintended writes to the
CTRL_CORE_PAD_* registers while Manual IO Timing Modes are configured.
This approach is taken to allow for a generic driver to exist in kernel
world that has to be used carefully in required usecases.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
[tony@atomide.com: updated to use generic pinctrl functions, added
binding documentation, updated comments]
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If the pin controller driver is using devm_kzalloc, there may not be
anything to do for dt_free_map. Let's make it optional to avoid
unncessary boilerplate code.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Activate 4K UAR support for firmware versions that support it.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add fields to structs to convey to kernel an indication whether the
library supports multi UARs per page and return to the library the size
of a UAR based on the queried value.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Current check requests that new fields in struct
mlx5_ib_alloc_ucontext_req_v2 that are not known to the driver be zero.
This was introduced so new libraries passing additional information to
the kernel through struct mlx5_ib_alloc_ucontext_req_v2 will be notified
by old kernels that do not support their request by failing the
operation. This schecme is problematic since it requires libmlx5 to issue
the requests with descending input size for struct
mlx5_ib_alloc_ucontext_req_v2.
To avoid this, we require that new features that will obey the following
rules:
If the feature requires one or more fields in the response and the at
least one of the fields can be encoded such that a zero value means the
kernel ignored the request then this field will provide the indication
to the library. If no response is required or if zero is a valid
response, a new field should be added that indicates to the library
whether its request was processed.
Fixes: b368d7cb8c ('IB/mlx5: Add hca_core_clock_offset to udata in init_ucontext')
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Make use of the blue flame registers allocator at mlx5_ib. Since blue
flame was not really supported we remove all the code that is related to
blue flame and we let all consumers to use the same blue flame register.
Once blue flame is supported we will add the code. As part of this patch
we also move the definition of struct mlx5_bf to mlx5_ib.h as it is only
used by mlx5_ib.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
A reference to a UAR is required to generate CQ or EQ doorbells. Since
CQ or EQ doorbells can all be generated using the same UAR area without
any effect on performance, we are just getting a reference to any
available UAR, If one is not available we allocate it but we don't waste
the blue flame registers it can provide and we will use them for
subsequent allocations.
We get a reference to such UAR and put in mlx5_priv so any kernel
consumer can make use of it.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sock_init() call it but not check it's return value,
so change it to void return and add an internal BUG_ON() check.
Signed-off-by: yuan linyu <Linyu.Yuan@alcatel-sbell.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Otherwise, RST packets generated by the TCP stack for non-existing
sockets always have mark 0.
The mark from the original packet is assigned to the netns_ipv4/6
socket used to send the response so that it can get copied into the
response skb when the socket sends it.
Fixes: e110861f86 ("net: add a sysctl to reflect the fwmark on replies")
Cc: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: Pau Espin Pedrol <pau.espin@tessares.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Otherwise, RST packets generated by ipt_REJECT always have mark 0 when
the routing is checked later in the same code path.
Fixes: e110861f86 ("net: add a sysctl to reflect the fwmark on replies")
Cc: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: Pau Espin Pedrol <pau.espin@tessares.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
In matches and targets that define a kernel-only tail to their
xt_match and xt_target data structs, add a field .usersize that
specifies up to where data is to be shared with userspace.
Performed a search for comment "Used internally by the kernel" to find
relevant matches and targets. Manually inspected the structs to derive
a valid offsetof.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Convert compat to copying entries, matches and targets one by one,
using the xt_match_to_user and xt_target_to_user helper functions.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Convert ebtables to copying entries, matches and targets one by one.
The solution is analogous to that of generic xt_(match|target)_to_user
helpers, but is applied to different structs.
Convert existing helpers ebt_make_XXXname helpers that overwrite
fields of an already copy_to_user'd struct with ebt_XXX_to_user
helpers that copy all relevant fields of the struct from scratch.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Convert arptables to copying entries, matches and targets one by one,
using the xt_match_to_user and xt_target_to_user helper functions.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Convert ip6tables to copying entries, matches and targets one by one,
using the xt_match_to_user and xt_target_to_user helper functions.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Convert iptables to copying entries, matches and targets one by one,
using the xt_match_to_user and xt_target_to_user helper functions.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
xt_entry_target, xt_entry_match and their private data may contain
kernel data.
Introduce helper functions xt_match_to_user, xt_target_to_user and
xt_data_to_user that copy only the expected fields. These replace
existing logic that calls copy_to_user on entire structs, then
overwrites select fields.
Private data is defined in xt_match and xt_target. All matches and
targets that maintain kernel data store this at the tail of their
private structure. Extend xt_match and xt_target with .usersize to
limit how many bytes of data are copied. The remainder is cleared.
If compatsize is specified, usersize can only safely be used if all
fields up to usersize use platform-independent types. Otherwise, the
compat_to_user callback must be defined.
This patch does not yet enable the support logic.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
SATA Host 0 clock is (as correctly documented) id 15/sata0.
Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Signed-off-by: Rob Herring <robh@kernel.org>
The generic IOMMU binding says that the meaning of an 'IOMMU specifier'
is defined by the binding of a specific SMMU. The ARM SMMU binding
never explicitly uses the term 'specifier' at all. Update implicit
references to use the explicit term.
In the iommu-map binding change references to iommu-specifier to
"IOMMU specifier" so we are 100% consistent everywhere with terminology
and capitalization.
Signed-off-by: Stuart Yoder <stuart.yoder@nxp.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Rob Herring <robh@kernel.org>
OMAP related files are actually named ehci-omap.txt and ohci-omap3.txt.
Also add full path to ohci-omap3.txt.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
On PowerPC machines some PCI slots might not have level triggered
interrupts capability (also know as level signaled interrupts),
leading of_irq_parse_pci() to complain by presenting error messages
on the kernel log - in this case, the properties "interrupt-map" and
"interrupt-map-mask" are not present on device's node in the device
tree.
This patch introduces a different message for this specific case,
and also reduces its level from error to warning. Besides, we warn
(once) that possibly some PCI slots on the system have no level
triggered interrupts available.
We changed some error return codes too on function of_irq_parse_raw()
in order other failure's cases can be presented in a more precise way.
Before this patch, when an adapter was plugged in a slot without level
interrupts capabilitiy on PowerPC, we saw a generic error message
like this:
[54.239] pci 002d:70:00.0: of_irq_parse_pci() failed with rc=-22
Now, with this applied, we see the following specific message:
[16.154] pci 0014:60:00.1: of_irq_parse_pci: no interrupt-map found,
INTx interrupts not available
Finally, we standardize the error path in of_irq_parse_raw() by always
taking the fail path instead of returning directly from the loop.
Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Signed-off-by: Rob Herring <robh@kernel.org>
The dma_fence.error field (formerly known as dma_fence.status) is an
optional field that may be set by drivers before calling
dma_fence_signal(). The field can be used to indicate that the fence was
completed in err rather than with success, and is visible to other
consumers of the fence and to userspace via sync_file.
This patch renames the field from status to error so that its meaning is
hopefully more clear (and distinct from dma_fence_get_status() which is
a composite between the error state and signal state) and adds a helper
that validates the preconditions of when it is suitable to adjust the
error field.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Sumit Semwal <sumit.semwal@linaro.org>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170104141222.6992-3-chris@chris-wilson.co.uk
Replace the sparse 256-pointer array for looking up protocol strings by
a switch() statement to reduce kernel size.
According to bloat-o-meter, this saves 910 bytes on m68k (32-bit), and
1892 bytes on arm64 (64-bit).
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Use SECINITSID_SECURITY as the default SID for booleans which don't have
a matching SID returned from security_genfs_sid(), also update the
error message to a warning which matches this.
This prevents the policy failing to load (and consequently the system
failing to boot) when there is no default genfscon statement matched for
the selinuxfs in the new policy.
Signed-off-by: Gary Tierney <gary.tierney@gmx.com>
Acked-by: Stephen Smalley <sds@tycho.nsa.gov>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Adds error logging to the code paths which can fail when loading a new
policy in sel_write_load(). If the policy fails to be loaded from
userspace then a warning message is printed, whereas if a failure occurs
after loading policy from userspace an error message will be printed
with details on where policy loading failed (recreating one of /classes/,
/policy_capabilities/, /booleans/ in the SELinux fs).
Also, if sel_make_bools() fails to obtain an SID for an entry in
/booleans/* an error will be printed indicating the path of the
boolean.
Signed-off-by: Gary Tierney <gary.tierney@gmx.com>
Acked-by: Stephen Smalley <sds@tycho.nsa.gov>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Processes can only alter their own security attributes via
/proc/pid/attr nodes. This is presently enforced by each individual
security module and is also imposed by the Linux credentials
implementation, which only allows a task to alter its own credentials.
Move the check enforcing this restriction from the individual
security modules to proc_pid_attr_write() before calling the security hook,
and drop the unnecessary task argument to the security hook since it can
only ever be the current task.
Signed-off-by: Stephen Smalley <sds@tycho.nsa.gov>
Acked-by: Casey Schaufler <casey@schaufler-ca.com>
Acked-by: John Johansen <john.johansen@canonical.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
SELinux was sometimes using the task "objective" credentials when
it could/should use the "subjective" credentials. This was sometimes
hidden by the fact that we were unnecessarily passing around pointers
to the current task, making it appear as if the task could be something
other than current, so eliminate all such passing of current. Inline
various permission checking helper functions that can be reduced to a
single avc_has_perm() call.
Since the credentials infrastructure only allows a task to alter
its own credentials, we can always assume that current must be the same
as the target task in selinux_setprocattr after the check. We likely
should move this check from selinux_setprocattr() to proc_pid_attr_write()
and drop the task argument to the security hook altogether; it can only
serve to confuse things.
Signed-off-by: Stephen Smalley <sds@tycho.nsa.gov>
Signed-off-by: Paul Moore <paul@paul-moore.com>
commit aad82892af ("selinux: Add support for
unprivileged mounts from user namespaces") prohibited any use of context
mount options within non-init user namespaces. However, this breaks
use of context mount options for tmpfs mounts within user namespaces,
which are being used by Docker/runc. There is no reason to block such
usage for tmpfs, ramfs or devpts. Exempt these filesystem types
from this restriction.
Before:
sh$ userns_child_exec -p -m -U -M '0 1000 1' -G '0 1000 1' bash
sh# mount -t tmpfs -o context=system_u:object_r:user_tmp_t:s0:c13 none /tmp
mount: tmpfs is write-protected, mounting read-only
mount: cannot mount tmpfs read-only
After:
sh$ userns_child_exec -p -m -U -M '0 1000 1' -G '0 1000 1' bash
sh# mount -t tmpfs -o context=system_u:object_r:user_tmp_t:s0:c13 none /tmp
sh# ls -Zd /tmp
unconfined_u:object_r:user_tmp_t:s0:c13 /tmp
Signed-off-by: Stephen Smalley <sds@tycho.nsa.gov>
Signed-off-by: Paul Moore <paul@paul-moore.com>
commit 79c8b348f215 ("selinux: support distinctions among all network
address families") mapped datagram ICMP sockets to the new icmp_socket
security class, but left ICMPv6 sockets unchanged. This change fixes
that oversight to handle both kinds of sockets consistently.
Signed-off-by: Stephen Smalley <sds@tycho.nsa.gov>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Since kernel 4.1 ftrace is supported as a new separate filesystem. It
gets automatically mounted by the kernel under the old path
/sys/kernel/debug/tracing. Because it lives now on a separate filesystem
SELinux needs to be updated to also support setting SELinux labels
on tracefs inodes. This is required for compatibility in Android
when moving to Linux 4.1 or newer.
Signed-off-by: Yongqin Liu <yongqin.liu@linaro.org>
Signed-off-by: William Roberts <william.c.roberts@intel.com>
Acked-by: Stephen Smalley <sds@tycho.nsa.gov>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Extend SELinux to support distinctions among all network address families
implemented by the kernel by defining new socket security classes
and mapping to them. Otherwise, many sockets are mapped to the generic
socket class and are indistinguishable in policy. This has come up
previously with regard to selectively allowing access to bluetooth sockets,
and more recently with regard to selectively allowing access to AF_ALG
sockets. Guido Trentalancia submitted a patch that took a similar approach
to add only support for distinguishing AF_ALG sockets, but this generalizes
his approach to handle all address families implemented by the kernel.
Socket security classes are also added for ICMP and SCTP sockets.
Socket security classes were not defined for AF_* values that are reserved
but unimplemented in the kernel, e.g. AF_NETBEUI, AF_SECURITY, AF_ASH,
AF_ECONET, AF_SNA, AF_WANPIPE.
Backward compatibility is provided by only enabling the finer-grained
socket classes if a new policy capability is set in the policy; older
policies will behave as before. The legacy redhat1 policy capability
that was only ever used in testing within Fedora for ptrace_child
is reclaimed for this purpose; as far as I can tell, this policy
capability is not enabled in any supported distro policy.
Add a pair of conditional compilation guards to detect when new AF_* values
are added so that we can update SELinux accordingly rather than having to
belatedly update it long after new address families are introduced.
Signed-off-by: Stephen Smalley <sds@tycho.nsa.gov>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Now that we have a common pinctrl driver for all the sun5i SoCs, we can
remove the old, separate drivers.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Now that it's obvious what the helpers do, we can simplify the code
somewhat by using them when clearing the pdpe/pml4e with the relevant
scratch entry.
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Michał Winiarski <michal.winiarski@intel.com>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20161213160512.7008-1-matthew.auld@intel.com
The function name gen8_setup_page_directory_pointer is misleading, and
only serves to confuse the reader, it's not setting up a pdp, but
rather encoding a specific pml4e with a given pdp.
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
The function name gen8_setup_page_directory is misleading, and only
serves to confuse the reader, it's not setting up a pd, but rather
encoding a specific pdpe with a given pd.
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
The sun5i SoCs (A10s, A13, GR8) are all based on the same die fit in
different packages. Hence, the pins and functions available are just the
based on the same set, each SoC having a different subset.
Introduce a common pinctrl driver that supports multiple variants to allow
to put as much as we can in common.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some SoCs are either supposed to be pin compatible (A10 and A20 for
example), or are just repackaged versions of the same die (A10s, A13, GR8).
In those case, having a full blown pinctrl driver just introduces
duplication in both data size and maintainance effort.
Add a variant option to both pins and functions to be able to limit the
pins and functions described only to a subset of the SoC we support with a
given driver.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The fence->status is an optional field that is only valid once the fence
has been signaled. (Driver may fill the fence->status with an error code
prior to calling dma_fence_signal().) Given the restriction upon its
validity, wrap querying of the fence->status into a helper
dma_fence_get_status().
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Sumit Semwal <sumit.semwal@linaro.org>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170104141222.6992-2-chris@chris-wilson.co.uk
As the fence->status is an optional field that may be set before
dma_fence_signal() is called to convey that the fence completed with an
error, we have to ensure that it is always set to zero on initialisation
so that the typical use (i.e. unset) always flags a successful completion.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Sumit Semwal <sumit.semwal@linaro.org>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170104141222.6992-1-chris@chris-wilson.co.uk
Revert to using direct register writes to set the divisor and
line-control registers.
A recent change switched to using the init vendor command to update
these registers, something which also enabled support for CH341A
devices. It turns out that simply setting bit 7 in the divisor register
is sufficient to support CH341A and specifically prevent data from being
buffered until a full endpoint-size packet (32 bytes) has been received.
Using the init command also had the side-effect of temporarily
deasserting the DTR/RTS signals on every termios change (including
initialisation on open) something which for example could cause problems
in setups where DTR is used to trigger a reset.
Fixes: 4e46c410e0 ("USB: serial: ch341: reinitialize chip on
reconfiguration")
Signed-off-by: Johan Hovold <johan@kernel.org>
A recent change added support for modifying the default line-control
settings, but did not make sure that the modified settings were used as
part of reconfiguration after a device has been reset during resume.
This caused a port that was open before suspend to be unusable until
being closed and reopened.
Fixes: ba781bdf86 ("USB: serial: ch341: add support for parity, frame
length, stop bits")
Signed-off-by: Johan Hovold <johan@kernel.org>
