Commit graph

691,473 commits

Author SHA1 Message Date
Christian Lamparter
2c7808d934 carl9170: fix hang in AP mode when HT STA does PSM
This is a obvious bug, skb_queue_walk does not
work if the iterator gets removed from the queue.

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-09-21 11:05:26 -04:00
Christian Lamparter
735761108f carl9170: reinit phy after HT settings have changed
The driver has a set of different initvals for 20 MHz
vs dynamic HT2040 operation. Because we can't change
some of the registers "in-flight", the driver needs to
perform a warm reset.

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-09-21 11:05:25 -04:00
Christian Lamparter
78ec789bd3 carl9170: fix state downgrade during reset
Don't mark the device as completely dead just yet.
If all goes to plan and carl9170_reboot succeeds
then we can skip the expensive userspace-driven
reinitialization anyway.

And if it doesn't and carl9170_reboot fails,
then carl9170_usb_cancel_urbs will do the
necessary steps.

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-09-21 11:05:24 -04:00
Christian Lamparter
cf6487d0d6 carl9170: abort tasklet during usb reset
This patch prevents the tasklet code from
interfering while the firmware is down for
an unscheduled maintenance.

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-09-21 11:05:23 -04:00
Christian Lamparter
9adc9e0ff3 carl9170: don't load bogus nf of chain 1
According to Atheros, chain 1 is not connected.

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-09-21 11:05:21 -04:00
Christian Lamparter
e278c5a903 carl9170: fix noise dBm conversion
Ever since carl9170 gained support to read the noisefloor,
the reported noisefloor level was pretty poor.

Initially I assumed that something was wrong in the PHY
setup and it would be impossible to fix without any
guidances. But this was not the case. In fact the nf
readings were correct and the thing that was broken
was the "simple" sign extension code!

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-09-21 11:05:20 -04:00
Christian Lamparter
9dec6f9c48 carl9170: use rx chainmask from eeprom
The eeprom provides a mask for all present rx chains.
Why not use it instead of the generic initval default?

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-09-21 11:05:19 -04:00
Bruno Randolf
e0b1cc52e5 ath5k: Add tx queue configuration function
Add the mac80211 callback function to configure the tx queue properties like
cw_min, cw_max and aifs.

Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-09-21 11:05:18 -04:00
Bruno Randolf
de8af45520 ath5k: Simplify cw_min/max and AIFS configuration
Get rid of overly complicated cw_min/max and AIFS configuration:

* Validate values in ath5k_hw_set_tx_queueprops(), so we can use them directly
  without further checks or computation in ath5k_hw_reset_tx_queue().

* Simplifiy by using AR5K_TUNE_AIFS|CWMIN|CWMAX variables directly since we
  don't support XR or B channels. That way we can also remove
  AR5K_TXQ_USEDEFAULT and the confusing logic around it.

* Update data types: AIFS is u8, CW's are u16.

* Remove now unneeded variables in ath5k_hw.

Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-09-21 11:05:16 -04:00
Bruno Randolf
234132960d ath5k: Keep last descriptor in queue
If we return a TX descriptor to the pool of available descriptors, while a
queues TXDP still points to it we could potentially run into all sorts of
troube.

It has been suggested that there is hardware which can set the descriptors
done bit before it reads ds_link and moves on to the next descriptor. While the
documentation says this is not true for newer chipsets (the descriptor contents
are copied to some internal memory), we don't know about older hardware.

To be safe, we always keep the last descriptor in the queue, and avoid dangling
TXDP pointers. Unfortunately this does not fully resolve the problem - queues
still get stuck!

This is similar to what ath9k does.

Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-09-21 11:05:15 -04:00
Bruno Randolf
923e5b3d3d ath5k: Count how many times a queue got stuck
Add a counter to show how many times a queue got stuck in the debugfs queue
file.

Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-09-21 11:05:14 -04:00
Bruno Randolf
4edd761f40 ath5k: Add watchdog for stuck TX queues
Since we do not know any better solution to the problem that TX queues can get
stuck, this adds a timer-based watchdog, which will check for stuck queues and
reset the hardware if necessary.

Ported from ath9k commit 164ace3853.

Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-09-21 11:05:12 -04:00
Bruno Randolf
1440401e70 ath5k: Move tx frame completion into separate function
Clearer separation between queue handling and what we do with completed frames.

Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-09-21 11:05:11 -04:00
Bruno Randolf
651d9375dc ath5k: Fix TX queues stopping
It does not make sense to stop queues for NF calibration. This will not stop
transmissions from the card, if there are queued packets.

If we run out of TX buffers we need to stop all queues, not only one.

Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-09-21 11:05:10 -04:00
Bruno Randolf
cfddc11c42 ath5k: Fix queue debug file
Take txq lock in debug file and fix reporting of used buffers.

Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-09-21 11:05:09 -04:00
Bruno Randolf
925e0b0613 ath5k: Use four hardware queues
Prepare ath5k for WME by using four hardware queues.

The way we set up our queues matches the mac80211 queue priority 1:1, so we
don't have to do any mapping for queue numbers.

Every queue uses 50 of the total 200 available transmit buffers, so the DMA
memory usage does not increase with this patch, but it might be good to
fine-tune the number of buffers per queue later (depending on the CPU speed and
load, and the speed of the medium access, it might not be big enough).

Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-09-21 11:05:08 -04:00
Bob Copeland
8a63facc37 ath5k: reorder base.c to remove fwd decls
This change reorganizes the main ath5k file in order to re-group
related functions and remove most of the forward declarations
(from 61 down to 3).  This is, unfortunately, a lot of churn, but
there should be no functional changes.

Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-09-21 11:05:06 -04:00
Bruno Randolf
ce2220d1da ath/ath5k/ath9k: Fix crypto capabilities merge issue
Fixing up a merge issue / concurrent development:

Remove unneeded ath_crypt_caps flags, as per "ath9k_hw: remove useless hw
capability flags" (364734fafb), but set the
AESCCM flag for ath9k. common ath code still needs a flag for this because
there is ath5k hardware which can't do AES in hardware.

Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-09-21 11:05:05 -04:00
Christian Lamparter
c807666a08 carl9170: update AR9170 phy initvals
This patch is loosely based on an ath9k patch called:
"ath9k_hw: sync initvals for ar9001 and ar9002 with Atheros"

It includes the following changes/fixes:
	- AGC setting improvements
	- timing changes for improved performance

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-09-21 11:05:04 -04:00
Ohad Ben-Cohen
80b517f362 omap: zoom: add mmc3/wl1271 device support
Add MMC3 support on ZOOM, which has the wl1271 device hardwired to.

The wl1271 is a 4-wire, 1.8V, embedded SDIO WLAN device with an
external IRQ line, and power-controlled by a GPIO-based fixed regulator.

Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-09-21 11:05:02 -04:00
Ohad Ben-Cohen
b642fde7f1 omap: zoom: add fixed regulator device for wlan
Add a fixed regulator vmmc device to enable power control
of the wl1271 wlan device.

Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-09-21 11:05:01 -04:00
Ohad Ben-Cohen
15cea99306 wl1271: make ref_clock configurable by board
The wl1271 device is using a reference clock that may change
between board to board.

Make the ref_clock parameter configurable by board settings
instead of having a hard coded value in the sources.

Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-09-21 11:05:00 -04:00
Ohad Ben-Cohen
09cecc340b wl1271: take irq info from private board data
Remove the hard coded irq information, and instead take
the irq information from the board's platform data.

Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-09-21 11:04:59 -04:00
Ohad Ben-Cohen
61ee7007a5 wl12xx: add platform data passing support
Add a simple mechanism to pass platform data to the
SDIO instances of wl12xx.

This way there is no confusion over who owns the 'embedded data',
typechecking is preserved, and no possibility for the wrong driver to
pick up the data.

Originally proposed by Russell King.

Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-09-21 11:04:57 -04:00
Ohad Ben-Cohen
2cc78ff78c wl1271: propagate set_power's return value
Make it possible for the set power method to indicate a
success/failure return value. This is needed to support
more complex power on/off operations such as SDIO
power manipulations.

Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Acked-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-09-21 11:04:56 -04:00
Nikanth Karthikesan
817f2c842d Fix various typos of valid in comments
Fix various typos of valid.

Signed-off-by: Nikanth Karthikesan <knikanth@suse.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2010-09-21 17:04:50 +02:00
Ohad Ben-Cohen
c1f9a09560 wl12xx: make wl12xx.h common to both spi and sdio
Move wl12xx.h outside of the spi-specific location,
so it can be shared with both spi and sdio solutions.

Update all users of spi/wl12xx.h accordingly

Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Acked-by: Luciano Coelho <luciano.coelho@nokia.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-09-21 11:04:38 -04:00
Nikanth Karthikesan
0bc79f7f58 Doc: Fix typo s/packages/packaged
Fix typo s/packages/packaged in Documentation/vm/numa_memory_policy.txt.

Signed-off-by: Nikanth Karthikesan <knikanth@suse.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2010-09-21 17:03:27 +02:00
Steven Rostedt
a8027073eb tracing/sched: Add sched_pi_setprio tracepoint
Add a tracepoint that shows the priority of a task being boosted
via priority inheritance.

Cc: Gregory Haskins <ghaskins@novell.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
2010-09-21 10:56:41 -04:00
Henrik Rydberg
46c4ba012c HID: 3m: Output proper orientation range
The range of orientation values for height/width devices should
be [0, 1], but is currently set to [1, 1]. Having min == max also
breaks uinput device setup. Fixed with this patch.

Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2010-09-21 16:16:09 +02:00
Henrik Rydberg
41035901df HID: 3m: Adjust to sequential MT HID protocol
The multitouch extensions to the HID protocol allows for contact
data to be sent over several reports, which is also the case for
the 3M M2256PW touchscreen. This patch modifies the logic to only
synchronize the input layer when all contacts have been received.
Consequentially, the full 60-finger capacity of the device is enabled.

Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Acked-by: Stephane Chatty <chatty@enac.fr>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2010-09-21 16:11:44 +02:00
Henrik Rydberg
24750f3e46 HID: Add a hid quirk for input sync override
As of lately, HID devices which send per-frame data split over several
HID reports have started to emerge. This patch adds a quirk which
allows the HID driver to take over the input layer synchronization,
and hence the control of the frame boundary.

Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2010-09-21 16:11:44 +02:00
Chris Wilson
9e0ae53404 drm/i915: Don't overwrite the returned error-code
During i915_gem_create_mmap_offset() if the subsystem reports an error
code, use it.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
2010-09-21 15:05:24 +01:00
Chris Wilson
4fd21dc8ee drm/i915/lvds: Unlock the PP register when panel-fitting
As we do not wait for the panel to turn off when we need to adjust the
panel-fitting registers we also need to unlock the PLLs as with the
non-pfit update path.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
2010-09-21 14:22:54 +01:00
Steven Rostedt
b3bc211cfe sched: Give CPU bound RT tasks preference
If a high priority task is waking up on a CPU that is running a
lower priority task that is bound to a CPU, see if we can move the
high RT task to another CPU first. Note, if all other CPUs are
running higher priority tasks than the CPU bounded current task,
then it will be preempted regardless.

Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Gregory Haskins <ghaskins@novell.com>
LKML-Reference: <20100921024138.888922071@goodmis.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
2010-09-21 13:57:12 +02:00
Steven Rostedt
43fa5460fe sched: Try not to migrate higher priority RT tasks
When first working on the RT scheduler design, we concentrated on
keeping all CPUs running RT tasks instead of having multiple RT
tasks on a single CPU waiting for the migration thread to move
them. Instead we take a more proactive stance and push or pull RT
tasks from one CPU to another on wakeup or scheduling.

When an RT task wakes up on a CPU that is running another RT task,
instead of preempting it and killing the cache of the running RT
task, we look to see if we can migrate the RT task that is waking
up, even if the RT task waking up is of higher priority.

This may sound a bit odd, but RT tasks should be limited in
migration by the user anyway. But in practice, people do not do
this, which causes high prio RT tasks to bounce around the CPUs.
This becomes even worse when we have priority inheritance, because
a high prio task can block on a lower prio task and boost its
priority. When the lower prio task wakes up the high prio task, if
it happens to be on the same CPU it will migrate off of it.

But in reality, the above does not happen much either, because the
wake up of the lower prio task, which has already been boosted, if
it was on the same CPU as the higher prio task, it would then
migrate off of it. But anyway, we do not want to migrate them
either.

To examine the scheduling, I created a test program and examined it
under kernelshark. The test program created CPU * 2 threads, where
each thread had a different priority. The program takes different
options. The options used in this change log was to have priority
inheritance mutexes or not.

All threads did the following loop:

static void grab_lock(long id, int iter, int l)
{
	ftrace_write("thread %ld iter %d, taking lock %d\n",
		     id, iter, l);
	pthread_mutex_lock(&locks[l]);
	ftrace_write("thread %ld iter %d, took lock %d\n",
		     id, iter, l);
	busy_loop(nr_tasks - id);
	ftrace_write("thread %ld iter %d, unlock lock %d\n",
		     id, iter, l);
	pthread_mutex_unlock(&locks[l]);
}

void *start_task(void *id)
{
	[...]
	while (!done) {
		for (l = 0; l < nr_locks; l++) {
			grab_lock(id, i, l);
			ftrace_write("thread %ld iter %d sleeping\n",
				     id, i);
			ms_sleep(id);
		}
		i++;
	}
	[...]
}

The busy_loop(ms) keeps the CPU spinning for ms milliseconds. The
ms_sleep(ms) sleeps for ms milliseconds. The ftrace_write() writes
to the ftrace buffer to help analyze via ftrace.

The higher the id, the higher the prio, the shorter it does the
busy loop, but the longer it spins. This is usually the case with
RT tasks, the lower priority tasks usually run longer than higher
priority tasks.

At the end of the test, it records the number of loops each thread
took, as well as the number of voluntary preemptions, non-voluntary
preemptions, and number of migrations each thread took, taking the
information from /proc/$$/sched and /proc/$$/status.

Running this on a 4 CPU processor, the results without changes to
the kernel looked like this:

Task        vol    nonvol   migrated     iterations
----        ---    ------   --------     ----------
  0:         53      3220       1470             98
  1:        562       773        724             98
  2:        752       933       1375             98
  3:        749        39        697             98
  4:        758         5        515             98
  5:        764         2        679             99
  6:        761         2        535             99
  7:        757         3        346             99

total:     5156       4977      6341            787

Each thread regardless of priority migrated a few hundred times.
The higher priority tasks, were a little better but still took
quite an impact.

By letting higher priority tasks bump the lower prio task from the
CPU, things changed a bit:

Task        vol    nonvol   migrated     iterations
----        ---    ------   --------     ----------
  0:         37      2835       1937             98
  1:        666      1821       1865             98
  2:        654      1003       1385             98
  3:        664       635        973             99
  4:        698       197        352             99
  5:        703       101        159             99
  6:        708         1         75             99
  7:        713         1          2             99

total:     4843       6594      6748            789

The total # of migrations did not change (several runs showed the
difference all within the noise). But we now see a dramatic
improvement to the higher priority tasks. (kernelshark showed that
the watchdog timer bumped the highest priority task to give it the
2 count. This was actually consistent with every run).

Notice that the # of iterations did not change either.

The above was with priority inheritance mutexes. That is, when the
higher prority task blocked on a lower priority task, the lower
priority task would inherit the higher priority task (which shows
why task 6 was bumped so many times). When not using priority
inheritance mutexes, the current kernel shows this:

Task        vol    nonvol   migrated     iterations
----        ---    ------   --------     ----------
  0:         56      3101       1892             95
  1:        594       713        937             95
  2:        625       188        618             95
  3:        628         4        491             96
  4:        640         7        468             96
  5:        631         2        501             96
  6:        641         1        466             96
  7:        643         2        497             96

total:     4458       4018      5870            765

Not much changed with or without priority inheritance mutexes. But
if we let the high priority task bump lower priority tasks on
wakeup we see:

Task        vol    nonvol   migrated     iterations
----        ---    ------   --------     ----------
  0:        115      3439       2782             98
  1:        633      1354       1583             99
  2:        652       919       1218             99
  3:        645       713        934             99
  4:        690         3          3             99
  5:        694         1          4             99
  6:        720         3          4             99
  7:        747         0          1            100

Which shows a even bigger change. The big difference between task 3
and task 4 is because we have only 4 CPUs on the machine, causing
the 4 highest prio tasks to always have preference.

Although I did not measure cache misses, and I'm sure there would
be little to measure since the test was not data intensive, I could
imagine large improvements for higher priority tasks when dealing
with lower priority tasks. Thus, I'm satisfied with making the
change and agreeing with what Gregory Haskins argued a few years
ago when we first had this discussion.

One final note. All tasks in the above tests were RT tasks. Any RT
task will always preempt a non RT task that is running on the CPU
the RT task wants to run on.

Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Gregory Haskins <ghaskins@novell.com>
LKML-Reference: <20100921024138.605460343@goodmis.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
2010-09-21 13:57:12 +02:00
Venkatesh Pallipadi
58b26c4c02 sched: Increment cache_nice_tries only on periodic lb
scheduler uses cache_nice_tries as an indicator to do cache_hot and
active load balance, when normal load balance fails. Currently,
this value is changed on any failed load balance attempt. That ends
up being not so nice to workloads that enter/exit idle often, as
they do more frequent new_idle balance and that pretty soon results
in cache hot tasks being pulled in.

Making the cache_nice_tries ignore failed new_idle balance seems to
make better sense. With that only the failed load balance in
periodic load balance gets accounted and the rate of accumulation
of cache_nice_tries will not depend on idle entry/exit (short
running sleep-wakeup kind of tasks). This reduces movement of
cache_hot tasks.

schedstat diff (after-before) excerpt from a workload that has
frequent and short wakeup-idle pattern (:2 in cpu col below refers
to NEWIDLE idx) This snapshot was across ~400 seconds.

Without this change:
domainstats:  domain0
 cpu     cnt      bln      fld      imb     gain    hgain  nobusyq  nobusyg
 0:2  306487   219575    73167  110069413    44583    19070     1172   218403
 1:2  292139   194853    81421  120893383    50745    21902     1259   193594
 2:2  283166   174607    91359  129699642    54931    23688     1287   173320
 3:2  273998   161788    93991  132757146    57122    24351     1366   160422
 4:2  289851   215692    62190  83398383    36377    13680      851   214841
 5:2  316312   222146    77605  117582154    49948    20281      988   221158
 6:2  297172   195596    83623  122133390    52801    21301      929   194667
 7:2  283391   178078    86378  126622761    55122    22239      928   177150
 8:2  297655   210359    72995  110246694    45798    19777     1125   209234
 9:2  297357   202011    79363  119753474    50953    22088     1089   200922
10:2  278797   178703    83180  122514385    52969    22726     1128   177575
11:2  272661   167669    86978  127342327    55857    24342     1195   166474
12:2  293039   204031    73211  110282059    47285    19651      948   203083
13:2  289502   196762    76803  114712942    49339    20547     1016   195746
14:2  264446   169609    78292  115715605    50459    21017      982   168627
15:2  260968   163660    80142  116811793    51483    21281     1064   162596

With this change:
domainstats:  domain0
 cpu     cnt      bln      fld      imb     gain    hgain  nobusyq  nobusyg
 0:2  272347   187380    77455  105420270    24975        1      953   186427
 1:2  267276   172360    86234  116242264    28087        6     1028   171332
 2:2  259769   156777    93281  123243134    30555        1     1043   155734
 3:2  250870   143129    97627  127370868    32026        6     1188   141941
 4:2  248422   177116    64096  78261112    22202        2      757   176359
 5:2  275595   180683    84950  116075022    29400        6      778   179905
 6:2  262418   162609    88944  119256898    31056        4      817   161792
 7:2  252204   147946    92646  122388300    32879        4      824   147122
 8:2  262335   172239    81631  110477214    26599        4      864   171375
 9:2  261563   164775    88016  117203621    28331        3      849   163926
10:2  243389   140949    93379  121353071    29585        2      909   140040
11:2  242795   134651    98310  124768957    30895        2     1016   133635
12:2  255234   166622    79843  104696912    26483        4      746   165876
13:2  244944   151595    83855  109808099    27787        3      801   150794
14:2  241301   140982    89935  116954383    30403        6      845   140137
15:2  232271   128564    92821  119185207    31207        4     1416   127148

Signed-off-by: Venkatesh Pallipadi <venki@google.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <1284167957-3675-1-git-send-email-venki@google.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
2010-09-21 13:57:11 +02:00
Ingo Molnar
cf84fd9632 Merge commit 'v2.6.36-rc5' into sched/core
Merge reason: Pick up the latest fixes in -rc5.

Signed-off-by: Ingo Molnar <mingo@elte.hu>
2010-09-21 13:56:49 +02:00
Peter Zijlstra
41945f6ccf perf: Avoid RCU vs preemption assumptions
The per-pmu per-cpu context patch converted things from
get_cpu_var() to this_cpu_ptr(), but that only works if
rcu_read_lock() actually disables preemption, and since
there is no such guarantee, we need to fix that.

Use the newly introduced {get,put}_cpu_ptr().

Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Tejun Heo <tj@kernel.org>
LKML-Reference: <20100917093009.308453028@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
2010-09-21 13:55:44 +02:00
Peter Zijlstra
8b8e2ec1ee percpu: Add {get,put}_cpu_ptr
These are similar to {get,put}_cpu_var() except for dynamically
allocated per-cpu memory.

Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Tejun Heo <tj@kernel.org>
LKML-Reference: <20100917093009.252867712@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
2010-09-21 13:55:43 +02:00
Ingo Molnar
7ed569206e Merge commit 'v2.6.36-rc5' into perf/core
Merge reason: Pick up the latest fixes in -rc5.

Signed-off-by: Ingo Molnar <mingo@elte.hu>
2010-09-21 13:55:11 +02:00
Suresh Siddha
f6c3f1686e sched: Fix nohz balance kick
There's a situation where the nohz balancer will try to wake itself:

cpu-x is idle which is also ilb_cpu
got a scheduler tick during idle
and the nohz_kick_needed() in trigger_load_balance() checks for
rq_x->nr_running which might not be zero (because of someone waking a
task on this rq etc) and this leads to the situation of the cpu-x
sending a kick to itself.

And this can cause a lockup.

Avoid this by not marking ourself eligible for kicking.

Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <1284400941.2684.19.camel@sbsiddha-MOBL3.sc.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
2010-09-21 13:50:50 +02:00
Chris Wilson
a6b17b4367 drm/i915: Use the correct DPB GMBUS port for GPIOE
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
2010-09-21 12:50:13 +01:00
Chris Wilson
cdd5998311 drm/i915: Drop crtc->fb pin on disable.
In order to handle disable_functions() where the framebuffer is
decoupled from the crtc we need to unpin the fb in order to prevent a
leak.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=29857
Reported-by: Sitsofe Wheeler <sitsofe@yahoo.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
2010-09-21 11:59:21 +01:00
Chris Wilson
6eecba33f2 drm/i915: Disable output polling across suspend & resume
Suspending (especially hibernating) may take a finite amount of time,
during which a hotplug event may trigger and we will attempt to handle
it with inconsistent state. Disable hotplug polling around suspend and
resume.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=30070
Reported-by: Rui Tiago Matos <tiagomatos@gmail.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
2010-09-21 11:57:15 +01:00
Daniel Vetter
ae83dd5c7d intel-gtt add a cleanup function for chipset specific stuff
The old code didn't clean up the i830 chipset flush page. And it
looks nicer.

Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
2010-09-21 11:40:41 +01:00
Daniel Vetter
22533b494f intel-gtt: store the dma mask size in intel_gtt_driver
Storing this explicitly makes for clearer code and hopefully
less further confusion.

Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
2010-09-21 11:40:28 +01:00
Daniel Vetter
0af9e92e77 intel-gtt: clean up gtt size reporting
Consolidate everything in intel-gtt.c and also kill the export
of intel_max_stolen.

Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
2010-09-21 11:40:06 +01:00
Daniel Vetter
aaa6259119 agp: kill agp_(unmap|map)_memory
DMA remapping was only used by the intel-gtt driver. With that
code now folded into the driver, kill the agp generic support for
it.

Cc: Dave Airlie <airlied@linux.ie>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
2010-09-21 11:39:52 +01:00
Daniel Vetter
e9b1cc81c2 intel-gtt: consolidate fake_agp driver structs
They're now all the same.

Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
2010-09-21 11:39:19 +01:00