When software initiates DAA (Dynamic Address Assignment), the controller
reports the result via the NRSPQP (Normal Response Queue Port Register).
The data length field of the response descriptor, which is accessible
through the NRSPQP register, indicates the number of devices remaining
after DAA. Consequently, when the bus is empty, this field contains the
maximum number of devices supported by the controller (8 for the Renesas
I3C controller).
Adjust the condition that computes the newly discovered devices bitmask
to prevent an out-of-bounds when the I3C bus is empty.
Fixes: e721898631 ("i3c: renesas: Add suspend/resume support")
Cc: stable@vger.kernel.org
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Tested-by: Tommaso Merciai <tommaso.merciai.xr@bp.renesas.com>
Link: https://patch.msgid.link/20260713130545.568657-9-claudiu.beznea+renesas@tuxon.dev
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The Renesas RZ/G3S SoC supports a power saving mode where power to most
SoC components, including I3C, is turned off.
On systems where the I3C devices also loses power during suspend (e.g. NXP
P3T1085UK-ARD connected to the PMOD1_6A connector of the RZ SMARC Carrier
2 + Renesas RZ/G3S SMARC SOM), the devices becomes unreachable after
resume.
Running DAA in the controller resume path restores communication. However,
DAA relies on interrupts for TX/RX, which are not available in the noirq
suspend/resume phase (unless they are wakeup interrupts). For this, the
suspend/resume callbacks were moved out of the noirq phase. Currently,
there is no identified use case on either the Renesas RZ/G3S or Renesas
RZ/G3E SoCs that requires the controller suspend/resume hooks to be part of
the noirq suspend/resume phase.
Since renesas_i3c_reset() is not called anymore in atomic context
update it to use read_poll_timeout().
Along with this, struct renesas_i3c::DATBASn and its usage were removed,
as they are no longer needed.
Fixes: e721898631 ("i3c: renesas: Add suspend/resume support")
Cc: stable@vger.kernel.org
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Tested-by: Tommaso Merciai <tommaso.merciai.xr@bp.renesas.com>
Link: https://patch.msgid.link/20260713130545.568657-7-claudiu.beznea+renesas@tuxon.dev
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reset the controller on resume after enabling the clocks to follow the
same sequence as in probe and avoid potential ordering related failures.
With it, renesas_i3c_reset() was updated to use read_poll_timeout_atomic(),
as the driver's resume callback is executed during the noirq phase of
resume, where interrupts are disabled.
Fixes: e721898631 ("i3c: renesas: Add suspend/resume support")
Cc: stable@vger.kernel.org
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Tested-by: Tommaso Merciai <tommaso.merciai.xr@bp.renesas.com>
Link: https://patch.msgid.link/20260713130545.568657-6-claudiu.beznea+renesas@tuxon.dev
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
During re-attach, the device may change its position in the i3c->addrs[]
array. As a result, it may use a different Device Address Table Basic
Register (DATBAS), which needs to be reconfigured.
Reconfigure the DATBAS register on re-attach. Along with it update
software caches.
Fixes: d028219a9f ("i3c: master: Add basic driver for the Renesas I3C controller")
Cc: stable@vger.kernel.org
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Tested-by: Tommaso Merciai <tommaso.merciai.xr@bp.renesas.com>
Link: https://patch.msgid.link/20260713130545.568657-5-claudiu.beznea+renesas@tuxon.dev
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Use the same reset deassert order in the resume and probe paths to avoid
potential failures due to ordering differences.
Fixes: e721898631 ("i3c: renesas: Add suspend/resume support")
Cc: stable@vger.kernel.org
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Tested-by: Tommaso Merciai <tommaso.merciai.xr@bp.renesas.com>
Link: https://patch.msgid.link/20260713130545.568657-4-claudiu.beznea+renesas@tuxon.dev
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The Renesas RZ/G3S supports a power saving state where power to the most
SoC componentes (including I3C) is lost.
The STDBR and EXTBR are configured in initialization phase though the
struct i3c_master_controller_ops::bus_init. Set them on resume function
as well to keep the same state of the controller after a suspend with
power loss and a similar initialization sequence as in bus_init.
Fixes: e721898631 ("i3c: renesas: Add suspend/resume support")
Cc: stable@vger.kernel.org
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Tested-by: Tommaso Merciai <tommaso.merciai.xr@bp.renesas.com>
Link: https://patch.msgid.link/20260713130545.568657-3-claudiu.beznea+renesas@tuxon.dev
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The Renesas I3C driver uses an asynchronous model to transfer data. It
prepares a struct renesas_i3c_xfer, enqueues it, and waits for completion.
The interrupt handler dequeues the transfer, updates/uses it, and signals
the waiting thread.
If the completion times out, the waiting thread dequeues the transfer and
free it. If an interrupt fires after that, the handler may access freed
memory, leading to crashes.
Check that the transfer is still valid before accessing it in the
interrupt handler. With it clear any status flags and disable all
the interrupts to avoid triggering the same interrupts again.
Fixes: d028219a9f ("i3c: master: Add basic driver for the Renesas I3C controller")
Cc: stable@vger.kernel.org
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Tested-by: Tommaso Merciai <tommaso.merciai.xr@bp.renesas.com>
Link: https://patch.msgid.link/20260713130545.568657-2-claudiu.beznea+renesas@tuxon.dev
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Add an I3C master driver and maintainers fragment for the AMD I3C bus
controller.
The driver currently supports the I3C bus operating in SDR mode,
with features including Dynamic Address Assignment, private data
transfers, and CCC transfers in both broadcast and direct modes. It
also supports operation in I2C mode.
The controller's data FIFOs are accessed big-endian; the driver performs
this conversion locally using ioread32be()/iowrite32be() with the
helpers, so it does not depend on any core FIFO-endianness helpers.
Signed-off-by: Manikanta Guntupalli <manikanta.guntupalli@amd.com>
Co-developed-by: Shubhrajyoti Datta <shubhrajyoti.datta@amd.com>
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@amd.com>
Co-developed-by: Shubham Patil <shubhamsanjay.patil@amd.com>
Signed-off-by: Shubham Patil <shubhamsanjay.patil@amd.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260709064233.1451482-3-shubhamsanjay.patil@amd.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Add optional_bytes to struct i3c_ccc_cmd_payload so callers describe
variable-length GET CCC responses. GETMRL and GETMXDS set optional_bytes
at the call site. Extend i3c_ccc_validate_payload_len() to honour it.
Signed-off-by: Adrian Ng Ho Yin <adrian.ho.yin.ng@altera.com>
Signed-off-by: Tze Yee Ng <tze.yee.ng@altera.com>
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Tested-by: Tommaso Merciai <tommaso.merciai.xr@bp.renesas.com>
Tested-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com> # on RZ/G3S
Link: https://patch.msgid.link/2e07dc944eab1c4358be1da87fa5000e711ac8bd.1783493868.git.tze.yee.ng@altera.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Add retries to struct i3c_ccc_cmd. Validate GET payload length in
i3c_master_send_ccc_cmd_locked() after a successful transfer.
Retry failed Direct GET CCCs up to cmd->retries times when the driver
reports failure or an I3C error; validation failures are not retried.
SET CCCs are not retried by default.
Signed-off-by: Adrian Ng Ho Yin <adrian.ho.yin.ng@altera.com>
Signed-off-by: Tze Yee Ng <tze.yee.ng@altera.com>
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Tested-by: Tommaso Merciai <tommaso.merciai.xr@bp.renesas.com>
Tested-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com> # on RZ/G3S
Link: https://patch.msgid.link/b467f01edfaaa0710f30e719ce7f2753b06c1a3f.1783493868.git.tze.yee.ng@altera.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Set dests[].payload.actual_len on successful GET CCC transfers in I3C
master drivers so the core can distinguish requested and received
buffer lengths. Switch core GET helpers to use actual_len instead of
len when interpreting GET CCC results.
Signed-off-by: Adrian Ng Ho Yin <adrian.ho.yin.ng@altera.com>
Signed-off-by: Tze Yee Ng <tze.yee.ng@altera.com>
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Tested-by: Tommaso Merciai <tommaso.merciai.xr@bp.renesas.com>
Tested-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com> # on RZ/G3S
Link: https://patch.msgid.link/6c66571ae7166aa4b87616d900e6d643631ac355.1783493868.git.tze.yee.ng@altera.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Add actual_len to struct i3c_ccc_cmd_payload so drivers can report how
many bytes were received on a GET CCC without overwriting the requested
buffer length in len.
Signed-off-by: Adrian Ng Ho Yin <adrian.ho.yin.ng@altera.com>
Signed-off-by: Tze Yee Ng <tze.yee.ng@altera.com>
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Tested-by: Tommaso Merciai <tommaso.merciai.xr@bp.renesas.com>
Tested-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com> # on RZ/G3S
Link: https://patch.msgid.link/e452777c3a9be734a97e20b9822d8a4264ceadba.1783493868.git.tze.yee.ng@altera.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
When device_register() fails in i3c_master_register_new_i3c_devs(),
put_device() is called to drop the reference taken by
device_register(). That drops the last reference, so the device's
release callback i3c_device_release() runs and frees the i3c_device.
Two problems follow from that:
i3c_device_release() does WARN_ON(i3cdev->desc), so it warns because
desc->dev->desc still points back at the descriptor. Clear it before
calling put_device().
After put_device() frees the i3c_device, desc->dev is left pointing at
freed memory, so clear desc->dev as well. That prevents, for example,
i3c_master_unregister_i3c_devs() seeing desc->dev as non-NULL and
dereferencing it.
Reported-by: sashiko-bot@kernel.org
Link: https://lore.kernel.org/linux-i3c/20260701203053.8F3971F000E9@smtp.kernel.org/
Fixes: cab63f6488 ("i3c: Fix potential refcount leak in i3c_master_register_new_i3c_devs")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260702183644.60827-1-adrian.hunter@intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
On an empty bus ENTDAA assigns nothing, so cmd->rx_len (the count
of addresses left unassigned) equals master->maxdevs.
The GENMASK() index master->maxdevs - cmd->rx_len - 1 then becomes -1,
which trips up UBSAN. This happens every time on boot on a Gigabyte/AMD
server:
UBSAN: shift-out-of-bounds in drivers/i3c/master/dw-i3c-master.c:905:12
shift exponent 64 is too large for 64-bit type 'long unsigned int'
CPU: 7 UID: 0 PID: 963 Comm: (udev-worker) Not tainted 7.0.11-200.fc44.x86_64 #1 PREEMPT(lazy)
Hardware name: Giga Computing E163-Z34-AAH1-000/MZ33-DC1-000, BIOS R32_F45 04/01/2026
Call Trace:
<TASK>
dump_stack_lvl+0x5d/0x80
ubsan_epilogue+0x5/0x2b
__ubsan_handle_shift_out_of_bounds.cold+0xd7/0x1ab
dw_i3c_master_daa.cold+0x1b/0x96 [dw_i3c_master]
i3c_master_do_daa_ext.part.0+0x3e/0xf0 [i3c]
Skip the mask when no new device was assigned.
Fixes: 1dd728f5d4 ("i3c: master: Add driver for Synopsys DesignWare IP")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260630172904.2662160-1-kuba@kernel.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
svc_i3c_master_handle_ibi() reads the IBI payload from the RX FIFO into
the IBI slot. The loop is bounded by the hardware FIFO size
(SVC_I3C_FIFO_SIZE), not by the slot size.
slot->data points into the IBI pool, which i3c_generic_ibi_alloc_pool()
sizes at max_payload_len per slot. svc_i3c_master_request_ibi() only
rejects a max_payload_len larger than SVC_I3C_FIFO_SIZE, so a driver can
request a smaller one. mctp-i3c requests 1. Each readsb() then copies the
controller RXCOUNT bytes (up to 31) with no check against the slot size.
A device that sends more bytes than the slot holds writes past
slot->data, an out-of-bounds write into the IBI pool.
Bound the loop by dev->ibi->max_payload_len and clamp each read to the
space left in the slot, the same way dw-i3c does. A device can still send
more than the requested payload. Flush the leftover bytes from the RX FIFO
so they do not leak into the next transfer.
Fixes: dd3c52846d ("i3c: master: svc: Add Silvaco I3C master driver")
Cc: stable@vger.kernel.org
Co-developed-by: Kaixuan Li <kaixuan.li@ntu.edu.sg>
Signed-off-by: Kaixuan Li <kaixuan.li@ntu.edu.sg>
Signed-off-by: Maoyi Xie <maoyixie.tju@gmail.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/178227747353.2931373.15868718612134648277@maoyixie.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
svc_i3c_master_xfer() emits STOP or force-exit for the final transfer
and then waits for the controller state to become idle, but ignores
readl_poll_timeout(). The function can therefore return success while
the controller is still not idle.
Return the idle-wait error through the existing warning/FIFO cleanup
path so the caller observes the failed transfer without emitting a
second STOP after the final STOP or force-exit has already been sent.
Signed-off-by: Pengpeng Hou <pengpeng@iscas.ac.cn>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://patch.msgid.link/20260623060821.23238-1-pengpeng@iscas.ac.cn
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
adi_i3c_master_probe() requests the IRQ and unmasks REG_IRQ_PENDING_CMDR
before the controller's IBI state, transfer queue list and transfer
queue lock are initialized. A pending CMDR interrupt can therefore run
adi_i3c_master_irq() and take master->xferqueue.lock before the dynamic
lock has been initialized.
This issue was found by our static analysis tool and then manually
reviewed against the current tree.
The grounded PoC kept the probe ordering and the IRQ path
adi_i3c_master_probe() -> adi_i3c_master_irq() -> xferqueue.lock, with a
pending CMDR interrupt arriving after REG_IRQ_PENDING_CMDR is unmasked.
Lockdep reported:
INFO: trying to register non-static key.
you didn't initialize this object before use?
lock_acquire+0xbb/0x290
_raw_spin_lock_irqsave+0x36/0x60
adi_i3c_master_irq+0x32/0x56 [vuln_msv]
adi_i3c_master_probe+0x5a/0xf47 [vuln_msv]
Initialize the transfer queue and IBI state before requesting and
unmasking the IRQ.
Fixes: a79ac2cdc9 ("i3c: master: Add driver for Analog Devices I3C Controller IP")
Cc: stable@vger.kernel.org
Signed-off-by: Runyu Xiao <runyu.xiao@seu.edu.cn>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260617150138.628578-1-runyu.xiao@seu.edu.cn
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
device removal, along with documentation fixes and minor AMD driver
cleanups.
-----BEGIN PGP SIGNATURE-----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=V3cD
-----END PGP SIGNATURE-----
Merge tag 'ntb-7.2' of https://github.com/jonmason/ntb
Pull NTB updates from Jon Mason:
"An EPF bug fix to prevent an invalid unmap during device removal,
along with documentation fixes and minor AMD driver cleanups"
* tag 'ntb-7.2' of https://github.com/jonmason/ntb:
ntb: amd: Use named initializer for pci_device_id::driver_data
NTB: fix kernel-doc warnings in ntb.h
NTB: epf: Avoid pci_iounmap() with offset when PEER_SPAD and CONFIG share BAR
ntb_hw_amd: Fix incorrect debug message in link disable path
- Updates to Synaptics RMI4 driver to fix potential OOB accesses in
F30 and F3A keymap handling
- A workaround in Synaptics RMI4 to tolerate buggy firmware on some
touchpads (e.g. ThinkPad T14 Gen 1) that report incomplete register
descriptor structures, preventing probe failures
- A revert of an incorrect register descriptor address calculation in
Synaptics RMI4 driver
- A fix for a regression in HP GSC PS/2 (gscps2) driver where the
receive buffer write index was not advanced, leaving keyboard and
mouse unusable.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQST2eWILY88ieB2DOtAj56VGEWXnAUCakCsxwAKCRBAj56VGEWX
nCICAQDSgfrAi+4SqTb92EjtdQO+ypluS42mKO75LTitJcS8dAEA1iKmdss8mGww
c4ai4W+UFxori7IqgkoQ7LfaPTOWlA0=
=QP4c
-----END PGP SIGNATURE-----
Merge tag 'input-for-v7.2-rc0-2' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull more input updates from Dmitry Torokhov:
- Updates to Synaptics RMI4 driver to fix potential OOB accesses in F30
and F3A keymap handling
- A workaround in Synaptics RMI4 to tolerate buggy firmware on some
touchpads (e.g. ThinkPad T14 Gen 1) that report incomplete register
descriptor structures, preventing probe failures
- A revert of an incorrect register descriptor address calculation in
Synaptics RMI4 driver
- A fix for a regression in HP GSC PS/2 (gscps2) driver where the
receive buffer write index was not advanced, leaving keyboard and
mouse unusable.
* tag 'input-for-v7.2-rc0-2' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: gscps2 - advance receive buffer write index
Input: rmi4 - tolerate short register descriptor structure
Revert "Input: rmi4 - fix register descriptor address calculation"
Input: synaptics-rmi4 - bound the F30 keymap to the GPIO/LED count
Input: synaptics-rmi4 - bound the F3A keymap to the GPIO count
Two more fixes that I managed to put into the public branch merged into
next before my first PR but missed to include them in it. The first
change is a relevant change that fixes misconfigurations due to a
variable overflow. The 2nd is only cosmetic but very obviously an
improvement.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEP4GsaTp6HlmJrf7Tj4D7WH0S/k4FAmpAE2gACgkQj4D7WH0S
/k7tnAgAsjkBQWoav1MF8kyVzew+iIuVvBrtUPimzeMs2gzwC1czi/TPKCvZxGND
XaPESmf51lC9AZuFd/2Wfvb2GydxA/wmsbVB0Q6ZBwLtS6/L4yiv3DpYN2to9yWN
QvVHeVCBdSbMHOQXdG0iFbhMiLyUX5YwCwyZT2cuVUHb4gvNLuDuKbgSXX9Odh1R
/p9C0afNMbdxuj2yRy+S8CM5Rl5v4yfBw6cswKX6w3uA+LnvksWuC8og7tEfFa/F
Vdwy4csWeKHGm7jEP9o6iSlWYy+DMKf5Llop+yFLZV6Db6AXMlEpNOXJsGxEv95y
qMTQFCGhepNWqVuUDDOOeUs60Asjpg==
=0WY9
-----END PGP SIGNATURE-----
Merge tag 'pwm/for-7.2-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/ukleinek/linux
Pull pwm fixes from Uwe Kleine-König:
"Two more fixes that I managed to put into the public branch merged
into next before my first pull request but missed to include them in
it.
The first change is a relevant change that fixes misconfigurations due
to a variable overflow. The second is only cosmetic but very obviously
an improvement"
* tag 'pwm/for-7.2-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/ukleinek/linux:
pwm: rzg2l-gpt: Add missing newlines to dev_err_probe() messages
pwm: rzg2l-gpt: Fix period_ticks type from u32 to u64
Fixes:
- fbcon: fix NULL pointer dereference for a console without vc_data [Ian Bridges]
- fbdev: fix fb_new_modelist to prevent null-ptr-deref in fb_videomode_to_var [Ian Bridges]
Fixes in failure paths:
- pm2fb: unwind write-cache setting on probe failure [Haoxiang Li]
- goldfishfb: fail pan display on base-update timeout [Pengpeng Hou]
- viafb: return error on DMA copy time-out [Pengpeng Hou]
- fbcon: fix out-of-bounds read in error path of fbcon_do_set_font() [Mingyu Wang]
- fbdev: fix modelist use-after-free in store_modes() [Ian Bridges]
Code cleanup:
- vga16fb: clean up platform_device_id table [Uwe Kleine-König]
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQS86RI+GtKfB8BJu973ErUQojoPXwUCakAKnwAKCRD3ErUQojoP
X27+AQCPvMJUMScjO1dlGKkPnnIFiOWCU6AW1aM2m6T+qWrCTQEAnNi5CCI3JiLi
6NCcyPm7/4R6tSXDm+UcWJ5tyzaNvww=
=EBHb
-----END PGP SIGNATURE-----
Merge tag 'fbdev-for-7.2-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/linux-fbdev
Pull more fbdev updates from Helge Deller:
"Fixes for generic fbdev & fbcon code for the handling of modelists
and preventing a potential NULL ptr dereference in the console code.
Fix missed cleanups in the error path of various fbdev drivers.
And Uwe Kleine-König contributed a cleanup patch to use named
initializers in the vga16fb driver"
* tag 'fbdev-for-7.2-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/linux-fbdev:
fbdev: Fix fb_new_modelist to prevent null-ptr-deref in fb_videomode_to_var
fbcon: fix NULL pointer dereference for a console without vc_data
fbdev: fix use-after-free in store_modes()
fbdev: viafb: return an error when DMA copy times out
fbdev: goldfishfb: fail pan display on base-update timeout
fbdev: fbcon: fix out-of-bounds read in err_out of fbcon_do_set_font()
fbdev: pm2fb: unwind WC setup on probe failure
fbdev: vga16fb: Drop unused assignment of platform_device_id driver data
A collection of small bug fixes accumulated over the last week.
Most are device-specific fixes while there are a few core fixes as
well.
Here are the highlights:
ALSA Core:
- A fix for an uninitialised heap leak in ALSA sequencer core
- A fix for error handling/resource leak in compress-offload API
USB-audio:
- A teardown-ordering fix in USB MIDI 2.0 to prevent use-after-free
- Bounds and length checks for packet data in Native Instruments caiaq
/ Traktor Kontrol input parsers
- Avoidance of expensive kobject path lookups in DualSense controller
matches
- Robustness/memory leak fixes for Qualcomm USB offload driver
- Focusrite Control Protocol (FCP) NULL-pointer dereference fix and a
new device quirk (ISA C8X)
- Device-specific quirks for Yamaha CDS3000 and SC13A
HD-Audio:
- A bunch of quirks and mute/mic-mute LED fixups for various laptops
(Acer, Clevo, Lenovo, HP)
ASoC & SoundWire:
- Avoid failing card registration if the device_link creation fails
- A workaround for SoundWire randconfig build failures by making
helper functions static inline
- Corrected MCLK reference validation for CS530x codecs
- Clean up of untested, problematic guard() macro replacements in
Rockchip SAI driver
- Fix for eDMA maxburst misalignment with channel count in Freescale
ASRC
- Miscellaneous hardware-specific fixes (qcom, rt5650, tlv320aic3x,
tas2781/3)
Others:
- Bounds and length checks for packet data in Apple iSight
-----BEGIN PGP SIGNATURE-----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=hJ5w
-----END PGP SIGNATURE-----
Merge tag 'sound-fix-7.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A collection of small bug fixes accumulated over the last week.
Most are device-specific fixes while there are a few core fixes as
well.
Here are the highlights:
ALSA Core:
- A fix for an uninitialised heap leak in ALSA sequencer core
- A fix for error handling/resource leak in compress-offload API
USB-audio:
- A teardown-ordering fix in USB MIDI 2.0 to prevent use-after-free
- Bounds and length checks for packet data in Native Instruments
caiaq / Traktor Kontrol input parsers
- Avoidance of expensive kobject path lookups in DualSense controller
matches
- Robustness/memory leak fixes for Qualcomm USB offload driver
- Focusrite Control Protocol (FCP) NULL-pointer dereference fix and a
new device quirk (ISA C8X)
- Device-specific quirks for Yamaha CDS3000 and SC13A
HD-Audio:
- A bunch of quirks and mute/mic-mute LED fixups for various laptops
(Acer, Clevo, Lenovo, HP)
ASoC & SoundWire:
- Avoid failing card registration if the device_link creation fails
- A workaround for SoundWire randconfig build failures by making
helper functions static inline
- Corrected MCLK reference validation for CS530x codecs
- Clean up of untested, problematic guard() macro replacements in
Rockchip SAI driver
- Fix for eDMA maxburst misalignment with channel count in Freescale
ASRC
- Miscellaneous hardware-specific fixes (qcom, rt5650, tlv320aic3x,
tas2781/3)
Others:
- Bounds and length checks for packet data in Apple iSight"
* tag 'sound-fix-7.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (46 commits)
ALSA: FCP: Fix NULL pointer dereference in interface lookup
ALSA: hda/realtek: Update Acer Nitro ANV15-41 quirk to enable mute LED
ASoC: fsl_asrc_dma: fix eDMA maxburst misalignment with channel count
ASoC: codecs: pcm512x: only print info once on no sclk
ASoC: tas2781: Update default register address to TAS2563
ALSA: firewire: isight: bound the sample count to the packet payload
ALSA: usb-audio: qcom: Free QMI handle
ALSA: hda: Add Lenovo Legion 7i 16IAX7 17AA3874 quirk
ALSA: usb-audio: avoid kobject path lookup in DualSense match
ALSA: hda/realtek: Add quirk for Acer Nitro ANV15-41
ASoC: soc-core: Don't fail if device_link could not be created
ASoC: rockchip: rockchip_sai: #include <linux/platform_device.h> explicitly
ALSA: seq: Fix uninitialised heap leak in snd_seq_event_dup()
ASoC: rt5575: Use __le32 for SPI burst write address
ASoC: tas2783: Update loaded firmware names to linux-firmware 20260519
ASoC: SDCA: Validate written enum value in ge_put_enum_double()
ASoC: realtek: Add back local call to sdw_show_ping_status()
ASoC: ti: Add back local call to sdw_show_ping_status()
ASoC: max98373: Add back local call to sdw_show_ping_status()
ASoC: es9356: Add back local call to sdw_show_ping_status()
...
Subsystem:
- add rtc_read_next_alarm() to read next expiring timer
Drivers:
- ds1307: handle OSF for ds1337/ds1339/ds3231, add clock provider for ds1307,
fix wday for rx8130
- m41t93: DT support, alarm, clock provider, watchdog support
- mv: add suspend/resume support for wakeup
- pcap: remove driver
- renesas-rtca3: many fixes
-----BEGIN PGP SIGNATURE-----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=SCOZ
-----END PGP SIGNATURE-----
Merge tag 'rtc-7.2' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC updates from Alexandre Belloni:
"Most of the work and improvements are for features of the m41t93.
The ds1307 also gets support for OSF (Oscillator Stop Flag) for
new variants.
The pcap driver is being removed as the Motorola EZX support was
removed a while ago.
Subsystem:
- add rtc_read_next_alarm() to read next expiring timer
Drivers:
- ds1307: handle OSF for ds1337/ds1339/ds3231, add clock provider for
ds1307, fix wday for rx8130
- m41t93: DT support, alarm, clock provider, watchdog support
- mv: add suspend/resume support for wakeup
- pcap: remove driver
- renesas-rtca3: many fixes"
* tag 'rtc-7.2' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (36 commits)
rtc: ds1307: update reference to removed CONFIG_RTC_DRV_DS1307_HWMON
platform/x86: amd-pmc: Fix S0i3 wakeup with alarmtimer
rtc: s35390a: fix typo in comment
rtc: cmos: unregister HPET IRQ handler on probe failure
rtc: ds1307: Fix off-by-one issue with wday for rx8130
dt-bindings: rtc: ds1307: Add epson,rx8901
rtc: bq32000: add delay between RTC reads
rtc: m41t93: Add watchdog support
rtc: m41t93: Add square wave clock provider support
rtc: m41t93: Add alarm support
rtc: m41t93: migrate to regmap api for register access
rtc: m41t93: add device tree support
dt-bindings: rtc: Add ST m41t93
rtc: ds1307: add support for clock provider in ds1307
rtc: mv: add suspend/resume support for wakeup
rtc: aspeed: add AST2700 compatible
dt-bindings: rtc: add ASPEED AST2700 compatible
rtc: interface: fix typos in rtc_handle_legacy_irq() documentation
rtc: msc313: fix NULL deref in shared IRQ handler at probe
rtc: remove unused pcap driver
...
- Fix a bug where in a specific edge case, file contents en/decryption
could be done with the wrong data unit size.
- Fix the data structure used for keeping track of users that have added
an fscrypt key to be a simple list instead of a 'struct key' keyring.
This fixes issues such as a lockdep report found by syzbot and
possible unintended interactions with the keyctl() system calls.
-----BEGIN PGP SIGNATURE-----
iIoEABYIADIWIQSacvsUNc7UX4ntmEPzXCl4vpKOKwUCaj8bBhQcZWJpZ2dlcnNA
a2VybmVsLm9yZwAKCRDzXCl4vpKOKyhIAP47lR+H783gopiz10Z7dwLQr2EHMfZ1
NcU7Zfq++AzZRQD/Tvv9/daqSh0OJTDNkBskSgVj6z7sRlQVNHY0wrD+QwE=
=LWES
-----END PGP SIGNATURE-----
Merge tag 'fscrypt-for-linus' of git://git.kernel.org/pub/scm/fs/fscrypt/linux
Pull fscrypt fixes from Eric Biggers:
- Fix a bug where in a specific edge case, file contents en/decryption
could be done with the wrong data unit size
- Fix the data structure used for keeping track of users that have
added an fscrypt key to be a simple list instead of a 'struct key'
keyring
This fixes issues such as a lockdep report found by syzbot and
possible unintended interactions with the keyctl() system calls
* tag 'fscrypt-for-linus' of git://git.kernel.org/pub/scm/fs/fscrypt/linux:
fscrypt: Replace mk_users keyring with simple list
fscrypt: Fix key setup in edge case with multiple data unit sizes
Commit 44f9200699 ("Input: gscps2 - use guard notation when
acquiring spinlock") moved the receive loop into gscps2_read_data()
and gscps2_report_data().
While moving the code, it preserved the writes to
buffer[ps2port->append], but omitted the following producer index
update from the original loop:
ps2port->append = (ps2port->append + 1) & BUFFER_SIZE;
As a result, append never advances. Since gscps2_report_data() only
reports bytes while act != append, the receive buffer always appears
empty and no keyboard or mouse data reaches the serio core.
Restore the omitted index update.
Fixes: 44f9200699 ("Input: gscps2 - use guard notation when acquiring spinlock")
Cc: stable@vger.kernel.org # 6.13+
Signed-off-by: Xu Rao <raoxu@uniontech.com>
Link: https://patch.msgid.link/460B5655BA580C60+20260624094739.850306-1-raoxu@uniontech.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Some touchpads (e.g. ThinkPad T14 Gen 1) have buggy firmware that reports
a register descriptor structure size that is too small for the number of
registers it claims to have in the presence map. The remaining bytes in
the structure are 0, which with the new strict bounds checking causes the
parser to fail with -EIO, aborting the device probe.
Tolerate such short reads by dropping the remaining (unparseable or
0-size) registers from the list instead of failing the probe,
preventing the driver from trying to use them.
Fixes: 0adb483fbf ("Input: rmi4 - refactor register descriptor parsing")
Reported-by: Barry K. Nathan <barryn@pobox.com>
Tested-by: Barry K. Nathan <barryn@pobox.com>
Cc: stable@vger.kernel.org
Assisted-by: Antigravity:gemini-3.5-flash
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The register descriptor presence register is a packet register, which
means its bytes share a single RMI address. It does not occupy
consecutive addresses, and the register structure that follows it
is located at the next RMI address (presence_address + 1), not
(presence_address + presence_size).
Revert the incorrect address calculation introduced in commit
a98518e724.
Reported-by: "Barry K. Nathan" <barryn@pobox.com>
Tested-by: "Barry K. Nathan" <barryn@pobox.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The current list initialisation depends on the well hidden two zeros in
the PCI_VDEVICE macro. Instead use a named initialisation that is more
robust and easier to understand.
Signed-off-by: Uwe Kleine-König (The Capable Hub) <u.kleine-koenig@baylibre.com>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Correct a function name and function parameter name to avoid
kernel-doc warnings:
Warning: include/linux/ntb.h:575 expecting prototype for
ntb_default_port_count(). Prototype was for ntb_default_peer_port_count()
instead
Warning: include/linux/ntb.h:590 function parameter 'pidx' not
described in 'ntb_default_peer_port_number'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
When BAR_PEER_SPAD and BAR_CONFIG share one PCI BAR, the module teardown
path ends up calling pci_iounmap() on the same iomem with some offset,
which is unnecessary and triggers a kernel warning like the following:
Trying to vunmap() nonexistent vm area (0000000069a5ffe8)
WARNING: mm/vmalloc.c:3470 at vunmap+0x58/0x68, CPU#5: modprobe/2937
[...]
Call trace:
vunmap+0x58/0x68 (P)
iounmap+0x34/0x48
pci_iounmap+0x2c/0x40
ntb_epf_pci_remove+0x44/0x80 [ntb_hw_epf]
pci_device_remove+0x48/0xf8
device_remove+0x50/0x88
device_release_driver_internal+0x1c8/0x228
driver_detach+0x50/0xb0
bus_remove_driver+0x74/0x100
driver_unregister+0x34/0x68
pci_unregister_driver+0x34/0xa0
ntb_epf_pci_driver_exit+0x14/0xfe0 [ntb_hw_epf]
[...]
Fix it by unmapping only when PEER_SPAD and CONFIG use difference bars.
Cc: stable@vger.kernel.org
Fixes: e75d5ae8ab ("NTB: epf: Allow more flexibility in the memory BAR map method")
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Koichiro Den <den@valinux.co.jp>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
amd_ntb_link_disable() prints "Enabling Link" which is misleading.
Update the message to reflect that the link is being disabled.
Signed-off-by: Alok Tiwari <alok.a.tiwari@oracle.com>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
sysfb
- drm/sysfb truncation and alignment fixes.
edid:
- fix edid OOB read in tile parsing
- increase displayid topology id to correct size.
nouveau:
- fix error handling paths in nouveau
amdxdna:
- get_bo_info fix.
ivpu:
- fix leak when error handling in ivpu.
-----BEGIN PGP SIGNATURE-----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=eLQl
-----END PGP SIGNATURE-----
Merge tag 'drm-fixes-2026-06-27' of https://gitlab.freedesktop.org/drm/kernel
Pull drm fixes from Dave Airlie:
"These are just the fixes from our fixes branch, all pretty small and
scattered.
sysfb:
- drm/sysfb truncation and alignment fixes
edid:
- fix edid OOB read in tile parsing
- increase displayid topology id to correct size
nouveau:
- fix error handling paths in nouveau
amdxdna:
- get_bo_info fix
ivpu:
- fix leak when error handling in ivpu"
* tag 'drm-fixes-2026-06-27' of https://gitlab.freedesktop.org/drm/kernel:
drm/sysfb: Avoid truncating maximum stride
drm/sysfb: Return errno code from drm_sysfb_get_visible_size()
drm/sysfb: Avoid possible truncation with calculating visible size
drm/sysfb: Do not page-align visible size of the framebuffer
drm/edid: fix OOB read in drm_parse_tiled_block()
drm/nouveau: fix reversed error cleanup order in ucopy functions
drm/nouveau/acr: fix missing nvkm_done() in error path of nvkm_acr_oneinit()
accel/amdxdna: Use caller client for debug BO sync
drm/displayid: fix Tiled Display Topology ID size
accel/ivpu: fix HWS command queue leak on registration failure
i915:
- Fix corrupted display output on GLK, #16209
- Add missing Spectre mitigation for parallel submit IOCTL
- MTL+ fix for DP resume
- clear CRTC blobs after dropping refs
- fix sharpness filter on DP MST
xe:
- Set TTM beneficial order to 9 in Xe
- Several error path cleanups
- Fix TDR for unstarted jobs on kernel queues
- Several TLB invalidation fixes related to suspending LR queues
- Some small RAS fixes
- Multi-queue suspend fix for LR queues
- Revert inclusion of NVL_S firmware
amdgpu:
- devcoredump fixes
- SMU15 fix
- Various irq put/get imbalance cleanup fixes
- 8K panel fix
- DCN3.5 fix
- lockdep fix
- Cleaner shader sysfs IB overflow fix
- Async flip fixes
- GET_MAPPING_INFO fix
- CP_GFX_SHADOW fix
- Ctx pstate handling fix
- GTT bo move handling fixes
- Old UVD BO placement fixes
- GC9 mode2 reset fix
- IH6.1 version fix
- Soft IH ring fix
amdkfd:
- Fix doorbell/mmio double unpin on free
- CRIU fixes
- SMI event fixes
- Sysfs teardown fix
- Various boundary checking fixes
- Various error checking fixes
- SVM fix
-----BEGIN PGP SIGNATURE-----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=qcB5
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2026-06-27' of https://gitlab.freedesktop.org/drm/kernel
Pull drm merge window fixes from Dave Airlie:
"This is the merge window fixes from our next tree, i915/xe and amdgpu
make up all of it.
I've got a separate fixes pull from our fixes branch arriving after
this.
i915:
- Fix corrupted display output on GLK, #16209
- Add missing Spectre mitigation for parallel submit IOCTL
- MTL+ fix for DP resume
- clear CRTC blobs after dropping refs
- fix sharpness filter on DP MST
xe:
- Set TTM beneficial order to 9 in Xe
- Several error path cleanups
- Fix TDR for unstarted jobs on kernel queues
- Several TLB invalidation fixes related to suspending LR queues
- Some small RAS fixes
- Multi-queue suspend fix for LR queues
- Revert inclusion of NVL_S firmware
amdgpu:
- devcoredump fixes
- SMU15 fix
- Various irq put/get imbalance cleanup fixes
- 8K panel fix
- DCN3.5 fix
- lockdep fix
- Cleaner shader sysfs IB overflow fix
- Async flip fixes
- GET_MAPPING_INFO fix
- CP_GFX_SHADOW fix
- Ctx pstate handling fix
- GTT bo move handling fixes
- Old UVD BO placement fixes
- GC9 mode2 reset fix
- IH6.1 version fix
- Soft IH ring fix
amdkfd:
- Fix doorbell/mmio double unpin on free
- CRIU fixes
- SMI event fixes
- Sysfs teardown fix
- Various boundary checking fixes
- Various error checking fixes
- SVM fix"
* tag 'drm-next-2026-06-27' of https://gitlab.freedesktop.org/drm/kernel: (52 commits)
drm/i915/cdclk: Fix up CDCLK_FREQ_DECIMAL without a full PLL re-enable
drm/i915/gem: Add missing nospec on parallel submit slot
drm/amdgpu: Use system unbound workqueue for soft IH ring
amdgpu/ih6.1: Fix minor version
drm/amdkfd: Use exclusive bounds for SVM split alignment checks
drm/amdgpu/gfx9: Fix Ring and IB test fail after mode2
drm/amdgpu/uvd: Fix forcing MSG, FB BOs into VCPU segment when it isn't at 0 (v2)
drm/amdgpu/uvd: Place VCPU BO only in VRAM for UVD 4.x and older
drm/amdgpu: Fix amdgpu_bo_move() when old_mem and new_mem are both GTT
drm/amdgpu: Respect placement requirements in amdgpu_gtt_mgr functions
drm/amdgpu: Fix context pstate override handling
drm/amdkfd: Use memdup_array_user to copy data from/to user space at kfd ioctls
drm/amdkfd: check find_first_zero_bit before __set_bit on kfd->doorbell_bitmap
drm/amdkfd: Let driver decide buffer size at AMDKFD_IOC_GET_DMABUF_INFO ioctl
drm/amdgpu: fix recursive ww_mutex acquire in amdgpu_devcoredump_format
drm/amdgpu: convert amdgpu_vm_lock_by_pasid() to drm_exec
drm/amdgpu: Don't use UTS_RELEASE directly
drm/amdkfd: Fix NULL deref during sysfs teardown
drm/amdgpu: validate CP_GFX_SHADOW chunk size in CS pass1
drm/amdgpu: check amdgpu_vm_bo_find() result in GET_MAPPING_INFO
...
operators to get out of tricky livelock situations involving caps and
file locks without evicting the problematic client instance on the MDS
side or rebooting the client node both of which can be disruptive.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEydHwtzie9C7TfviiSn/eOAIR84sFAmo+rNUTHGlkcnlvbW92
QGdtYWlsLmNvbQAKCRBKf944AhHzi++dB/0VE3YM+kdZER9Y1CoPgxB32CSD5Yoz
cscBQCGtFM/0GHj2rMnvyeQ9+uHlQqzo/CMYURUBJ4ciHPLaZUyuJcp8R7bGNgk2
FZ0+9yBqJjjeSJST16MKhW7/NgzuIhg8Y3c+sDrLDThYkbmEM90MYLDpopqwjLhc
RL1mURFBQxuBLQiYujKXit1iXqYapJSRmthJAYN4pJ69w97zF+rO/qfvUGlRxYb3
0Hb4GzD5IyWmsRGwldzc7/CXDLjTjp/N+tu1BLuCQK68U3MAw8GV39/aSocFjxN8
rtq8TkgFb1dfSjwjD8pxei5pjBaoUjABnTg8wPDFoxEMKrVpabMeUTsb
=xeGm
-----END PGP SIGNATURE-----
Merge tag 'ceph-for-7.2-rc1' of https://github.com/ceph/ceph-client
Pull ceph updates from Ilya Dryomov:
"This adds support for manual client session reset in CephFS, allowing
operators to get out of tricky livelock situations involving caps and
file locks without evicting the problematic client instance on the MDS
side or rebooting the client node both of which can be disruptive"
* tag 'ceph-for-7.2-rc1' of https://github.com/ceph/ceph-client:
ceph: add manual reset debugfs control and tracepoints
ceph: add client reset state machine and session teardown
ceph: add diagnostic timeout loop to wait_caps_flush()
ceph: harden send_mds_reconnect and handle active-MDS peer reset
ceph: use proper endian conversion for flock_len in reconnect
ceph: convert inode flags to named bit positions and atomic bitops
rbd: switch to dynamic root device
- Fix dangling resources on thermal_throttle_online() failure in the
Intel thermal_throttle driver (Ricardo Neri)
- Eliminate a possibility of running thermal testing module code after
that module has been removed (Rafael Wysocki)
-----BEGIN PGP SIGNATURE-----
iQFGBAABCAAwFiEEcM8Aw/RY0dgsiRUR7l+9nS/U47UFAmo+uqQSHHJqd0Byand5
c29ja2kubmV0AAoJEO5fvZ0v1OO1IRIH/iMuMYJuLL574TDOjxCjCCXzHthbp+vU
SQP24sEV8cRkpHu7Pf6LtqI4ofamyxlLRx0HbVEPaZieQRR/MdQAMbDXthDbWsDp
sJn7aWzWkyZLnkS/5f22SLqspgRIIYWxUPuLFEevCFo0RGQwneXIbTABYtJNgKJA
jmlvQNADX4w8NbEEXtdT08FGJt9xjn+X3VCrmLj1dU039hxVFzuKnABxFJsGiyqX
EV5DEOnlnEUA9uGZT7DeGO4oH+5XNkXEN9UAXXefh7hWesZZpOV+eDbANAiF/YTM
I2uCRuPImGffL6IWv5Vn8bnutBVKoys3BP5XZjKGoIfYopFGiwmXtcY=
=6VOr
-----END PGP SIGNATURE-----
Merge tag 'thermal-7.2-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull thermal control fixes from Rafael Wysocki:
"These fix a failure path in an Intel thermal driver and prevent
thermal testing module code from being executed after it has been
freed:
- Fix dangling resources on thermal_throttle_online() failure in the
Intel thermal_throttle driver (Ricardo Neri)
- Eliminate a possibility of running thermal testing module code
after that module has been removed (Rafael Wysocki)"
* tag 'thermal-7.2-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
thermal: testing: zone: Flush work items during cleanup
thermal: intel: Fix dangling resources on thermal_throttle_online() failure
- Remove a misguided warning along with an inaccurate comment next to
it from the cpuidle core (Rafael Wysocki)
- Clear need_freq_update as appropriate in the .adjust_perf()
path of the schedutil cpufreq governor to avoid calling
cpufreq_driver_adjust_perf() unnecessarily on every scheduler
utilization update (Zhongqiu Han)
-----BEGIN PGP SIGNATURE-----
iQFGBAABCAAwFiEEcM8Aw/RY0dgsiRUR7l+9nS/U47UFAmo+ujsSHHJqd0Byand5
c29ja2kubmV0AAoJEO5fvZ0v1OO1o5UH/0PUjz0I+HrrPi6O6Nt2vaA/o+fI8DRA
d+M2KbZqh1e/Jk8wMB9IwErFzolY6rrJ4HeBkzBo7VNIofgvljH7EwrrUhYhv1c1
xWViKUS6JUpAOwA+44tGKhiDU5PrNHyVDXqjJ5id6pfBiVMxtRcCCd1xBDQRNXg2
r3hRnUz9F3vP93AB0lujsSQeMj2g6XmTX+AyBmDcrYwrO/vZOao1OWNOnxfbt4Yd
TPokkyPCBuLAQYM7eDF1jMsbRqDIo4/zHbVMmVdUYzOd944S1Ruira89V5A7Txzg
Ih7DCct2UDwAMKubMYEVlCdSkXZl7IRXep+qDeOkLo3xhs0UORgEXwg=
=V/er
-----END PGP SIGNATURE-----
Merge tag 'pm-7.2-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These fix the schedutil cpufreq governor and drop a bogus warning
from the cpuidle core:
- Remove a misguided warning along with an inaccurate comment
next to it from the cpuidle core (Rafael Wysocki)
- Clear need_freq_update as appropriate in the .adjust_perf()
path of the schedutil cpufreq governor to avoid calling
cpufreq_driver_adjust_perf() unnecessarily on every scheduler
utilization update (Zhongqiu Han)"
* tag 'pm-7.2-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpuidle: Allow exit latency to exceed target residency
cpufreq: schedutil: Fix uncleared need_freq_update on the .adjust_perf() path
- Unbreak ACPICA tools builds after switching over to using
strscpy_pad() that is kernel-specific (Rafael Wysocki)
- Fix module parameter file paths in comments in the ACPI code managing
the general sysfs attributes (Zenghui Yu)
- Update kerneldoc comments in the ACPI resource management code to
follow the common style (Andy Shevchenko)
- Fix inverted interface check in ipmi_bmc_gone() that may cause ACPI
IPMI interfaces to be mishandled (Xu Rao)
- Add __cpuidle annotation to idle state management functions related
to ACPI _LPI to avoid trace-induced RCU warnings (Li RongQing)
-----BEGIN PGP SIGNATURE-----
iQFGBAABCAAwFiEEcM8Aw/RY0dgsiRUR7l+9nS/U47UFAmo+uaYSHHJqd0Byand5
c29ja2kubmV0AAoJEO5fvZ0v1OO1ozUH/i79gN5EF4jbXdpyAsL8f+G3JhSs54gG
VXpBUI4Wy56sLbWkJs1E9BzLpoUTPJb6PaYYNb+v2+MWnZSR/LzQTDprggeTLqm0
JbRCxBGFoN8yeSoWinUvSPCs6uVjqOMVe9yRvDTVcq+V+kpeNzkZnhGcy/1XQov8
5uur7kIggWqFo4ospTUi50caZDADOoZiZkZNNh/DRS1qmvE+XKN/8ZHSHkY5uZDa
GjK15Bf9E/cS13T5UglSOO/Vz/a/ZeGMgjSfozBirOo5VPIaJPecYPrAG4mNsCxz
0ZewK5zMaNrTf5owDAEVUml8D+/+F4Yp28q+vYQIdiuc+u3/FIr0a0w=
=TKWf
-----END PGP SIGNATURE-----
Merge tag 'acpi-7.2-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI support fixes and cleanups from Rafael Wysocki:
"These fix assorted issues and do cleanups in the ACPI support code,
which includes a fix for tools build breakage related to strncpy()
removal:
- Unbreak ACPICA tools builds after switching over to using
strscpy_pad() that is kernel-specific (Rafael Wysocki)
- Fix module parameter file paths in comments in the ACPI code
managing the general sysfs attributes (Zenghui Yu)
- Update kerneldoc comments in the ACPI resource management code to
follow the common style (Andy Shevchenko)
- Fix inverted interface check in ipmi_bmc_gone() that may cause ACPI
IPMI interfaces to be mishandled (Xu Rao)
- Add __cpuidle annotation to idle state management functions related
to ACPI _LPI to avoid trace-induced RCU warnings (Li RongQing)"
* tag 'acpi-7.2-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: processor_idle: Mark LPI enter functions as __cpuidle
ACPICA: Unbreak tools build after switching over to strscpy_pad()
ACPI: IPMI: Fix inverted interface check in ipmi_bmc_gone()
ACPI: resource: Amend kernel-doc style
ACPI: sysfs: Fix path of module parameters in comments
A fairly unremarkable collection of fixes that came in over the merge
window, plus a new device ID for the DesignWare controller in the
StarFive JHB100 SoC. There's a couple of core fixes included, one
avoiding freeing an empty resource in error handling cases and another
which fixes a NULL dereference which could be triggered by using an
abnormal device registration flow like driver_override.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmo+eSgACgkQJNaLcl1U
h9BiLwf+LSC77vZ/sKOJLV9CZnIq1ZOi5YVRXKbRLNhnFHIU2DetRXeGnRUmNr7s
WJFV6BO1i8eyYcoX/dyb3nf9kFX6dH1fw6FDby8QfA54b9cPkEZqNsl/K+3+Xbwb
3OJwv4zubDdFbr/qLCqMewAHdHSzefc02CbOeRdGv/AerPTa+r5WqXXWqZC2YKku
rhweANmQl0TUufHOaYSBaVDVHRGjblHDg6j9pLoUw2s1jPznIB/tqG8CPXnsiajl
ii6WgR6inaURBpW2LGaLlHiQ4qKJXlxV7uFWVY2KRPUVqHkW6rQj4K4Sa0pnbdz3
4t/5Afm4esZvMathb3lmPmsH7zIKcQ==
=Gy0X
-----END PGP SIGNATURE-----
Merge tag 'spi-fix-v7.2-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A fairly unremarkable collection of fixes that came in over the
merge window, plus a new device ID for the DesignWare controller
in the StarFive JHB100 SoC.
There's a couple of core fixes included, one avoiding freeing an
empty resource in error handling cases and another which fixes a
NULL dereference which could be triggered by using an abnormal
device registration flow like driver_override"
* tag 'spi-fix-v7.2-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: imx: reconfigure for PIO when DMA cannot be started
spi: dw: Add support for snps,dwc-ssi-2.00a
spi: dt-bindings: snps,dw-apb-ssi: Add starfive,jhb100-spi
spi: rpc-if: Use correct device for hardware reinitialization on resume
spi: acpi: Free resource list at appropriate time
spi: dw: fix wrong BAUDR setting after resume
spi: uniphier: Fix completion initialization order before devm_request_irq()
spi: Add NULL check for spi_get_device_id() in spi_get_device_match_data()
A couple of unremarkable driver specific fixes that came in during the
merge window.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmo+eU4ACgkQJNaLcl1U
h9At2Af/esobd0NX/EF1D19GsDEQYytbDo6ZQ6Gu3mK+nJIGs9R5uwlHkN4otaSV
P2FmaK1QjolNXLdHT0chO93SspouNlcAoWiGhjzxTJG1dqNGJJSIh5D+iJrivhIN
hUbld2OxgGxVbcPhl7jDAZGnnoALIFtGe+vWsMw9/Y5GHXCJGcdyKYbvDm5+KqH1
DUeufn2MmBayQzi48ZEr9+GNEd9tR7cxV8IWVSB40Gf6NPasneoNTXW86dwAkYz0
sSyRGYJLrfYR/jpVGHRcuc1zX0kYedOdfdDuHcEc89nw/wzfgeN9dLw/z2DOwXnN
hv3aea4vnhneHFLgg0D8RyDHpkM3Zw==
=arcc
-----END PGP SIGNATURE-----
Merge tag 'regulator-fix-v7.2-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"A couple of unremarkable driver specific fixes that came in during the
merge window"
* tag 'regulator-fix-v7.2-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: da9121: Use subvariant ids in the I2C table
regulator: pca9450: Correct default t_off_deb for PCA9451A/PCA9452
A fix to ensure that we don't overwrite the error code when cleaning up
a failed cache initialisation, helping people debug issues if they do
arise.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmo+eagACgkQJNaLcl1U
h9D09Af9GOgk/Fk+qOS8Ns4wzVmOaFEG3AhNpqhnKjX3kaI/9Sj2S+oVFzQL6jJP
za2vtYNthXWb2s/zwUCdcWO12mgrp12L+3O5FU786ihxW1WhHvNnmgEo2Cunr0Jr
mORqKimyBqW27MFtpU2lHvnt2BwF3oc2ixZHK7j0sLid/74o7gtVFrHjCfoMS5Lf
oITWMWExyRZ8DpOXNyFFl304ZvBwiHOloB0qIZPa7EV3GCL4fuUMl9dMi1mBPG1i
hISYK8kkYvNUcgCsg83zlbcmrPzShPAyc5twZwhltAUwQ9qLSygnPKDbdqkKgSUq
WT1/9gHyfR5XH/h3bATrPFQcW2RmoA==
=Ve1C
-----END PGP SIGNATURE-----
Merge tag 'regmap-fix-v7.2-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap fix from Mark Brown:
"Ensure that we don't overwrite the error code when cleaning up a
failed cache initialisation, helping people debug issues if they
do arise"
* tag 'regmap-fix-v7.2-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regcache: Do not overwrite error code when finalizing cache after error
Merge a fix eliminating a possibility of running the thermal testing
module code after that module has been removed.
* thermal-testing:
thermal: testing: zone: Flush work items during cleanup
Merge a cpuidle core fix that removes a misguided warning along with an
inaccurate comment next to it.
* pm-cpuidle:
cpuidle: Allow exit latency to exceed target residency
Merge an update of comments regarding the ACPI sysfs code, a kernel-doc
style fixup update of ACPI resource management, and ACPI IPMI driver
fix, and an ACPI processor driver fix for 7.2-rc1:
- Fix module parameter file paths in comments in the ACPI code managing
the general sysfs attributes (Zenghui Yu)
- Update kerneldoc comments in the ACPI resource management code to
follow the common style (Andy Shevchenko)
- Fix inverted interface check in ipmi_bmc_gone() which may cause ACPI
IPMI interfaces to be mishandled (Xu Rao)
- Add __cpuidle to idle state management functions related to ACPI _LPI
to avoid trace-induced RCU warnings (Li RongQing)
* acpi-sysfs:
ACPI: sysfs: Fix path of module parameters in comments
* acpi-resource:
ACPI: resource: Amend kernel-doc style
* acpi-driver:
ACPI: IPMI: Fix inverted interface check in ipmi_bmc_gone()
* acpi-processor:
ACPI: processor_idle: Mark LPI enter functions as __cpuidle
- Drop unnecessary type reference from khadas,mcu "fan-supply"
- Fix clocks in Renesas R-Mobile APE6 example
- Add missing Unisoc SC2730 PMIC regulators schema
- Fix Amlogic thermal example
- kernel-doc fix for of_map_id()
- Handle negative index in of_fwnode_get_reference_args()
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEktVUI4SxYhzZyEuo+vtdtY28YcMFAmo9lgUACgkQ+vtdtY28
YcMHdg//b53t64fBQF7AhVO0mp/EJLYvvCnKZ0iWw1N0Ya7WgKFMtl6UhYoxfkn5
8Q+q18rCaV6v9cP933RQ1zgdYeEavmP1ev1tpuW3MzWFRGQykJt1tgtwr1LTFEDK
NbalsaAiAbihn1Tn22gXDAddy8ghI0AyZoSDvLrUx1mlO2dZjOgg2tSt/yzmZIBf
00ZKmu6lcqmdvoitWkjN2CmFuyTATQ3+7mGJvTgPUx9FRvF/xSGHgzxkN3eHnMhC
MhYLZQMtmJ4xkRSZ1NC/OBbgSftzIbpYsZTMsG1KUJpXdGAdcz3LPUVWLWAlaqIb
sP6bu7i7x42zPF+m2BkdA9N5pdJsPNBNaR1rdcZykq9qiN+nfQkUUK16TlznQd0t
xH+wBrMZcHjoZuBpP1vzEuFc/GyGIxWOTCmjgCXXOHLxUDt17V5COHBziLa+/w1O
e++M4QYy+/1irPeTq8obr8uSSkHthbwomwWm55yfuuC+gs5tKYGoLnuyHswP4Eza
E5Usz7VlInMfF6x0yADAPlcpAymp5VdnLFnWktSv0CHo69Tac0EbgWsGMB6HV9c/
2ZawGm5yNIfoBNggA2UodgN9QDomi8I+tATCmClvZo6yR5Jaus669/s7ELMHBfgw
35RktyT0cS4z8OvkhdADWAdBIC0KGWl0PKdoqqkXITEaR/t7FjY=
=/1jq
-----END PGP SIGNATURE-----
Merge tag 'devicetree-fixes-for-7.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree fixes from Rob Herring:
- Drop unnecessary type reference from khadas,mcu "fan-supply"
- Fix clocks in Renesas R-Mobile APE6 example
- Add missing Unisoc SC2730 PMIC regulators schema
- Fix Amlogic thermal example
- kernel-doc fix for of_map_id()
- Handle negative index in of_fwnode_get_reference_args()
* tag 'devicetree-fixes-for-7.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
dt-bindings: mfd: khadas,mcu: Drop type reference from "fan-supply"
dt-bindings: clock: renesas: div6: Use ZT/ZTR trace clock in R-Mobile APE6 example
regulator: dt-bindings: Add Unisoc SC2730 PMIC
dt-bindings: thermal: amlogic: Correct 'reg' in the example
dt-bindings: thermal: amlogic: Fix missing header in the example
of: Fix RST inline emphasis warnings in of_map_id() kernel-doc
of: property: Fix of_fwnode_get_reference_args() with negative index
