TIPC can encrypt traffic between nodes using a different transmit key
for each node. In this mode, the AES-GCM nonce for a packet sent to a
known peer consists of a 32-bit prefix (a per-key salt XOR the peer's
address) followed by a 64-bit counter. That counter is stored in the
peer's RX crypto object. When the peer reports a change in which key
it uses to receive packets, TIPC resets this counter. The sender can
still be using the same TX key and salt, so subsequent packets reuse
earlier nonces. This nonce reuse breaks confidentiality and exposes
GCM's authentication key. This makes forgeries trivial: an attacker
can exploit CTR malleability to alter captured ciphertexts and use the
recovered authentication key to compute a valid tag for the modified
ciphertext, under the same key and nonce.
Use the TX key's existing aead->seqno counter instead. All encryptions
using that key object share the same atomic counter, so concurrent
encryptions get distinct nonce counter values. The counter survives
key activation and peer reconnection, and peer key-status reports
cannot reset it. This prevents those transitions from causing nonce
reuse while the same TX key remains installed.
The nonce format is unchanged, and receivers do not require consecutive
counter values, so sharing the counter across peers remains compatible
with existing receivers. A pre-existing check still invokes key
revocation in the unlikely event that the counter wraps to zero.
Fixes: fc1b6d6de2 ("tipc: introduce TIPC encryption & authentication")
Signed-off-by: Jérémy Jean <Jeremy.Jean@oss.cyber.gouv.fr>
Reviewed-by: Tung Nguyen <tung.quang.nguyen@est.tech>
Link: https://patch.msgid.link/20260924202105.3722778-1-Jeremy.Jean@oss.cyber.gouv.fr
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Subrat Pandey says:
====================
octeontx2: Misc fixes for RVU drivers
A few independent fixes for the Marvell OcteonTX2 (RVU AF/PF) drivers:
- Fix aura/CQ BPID assignment under CONFIG_DCB, which assumed
queue_to_pfc_map was always allocated (not true for SDP VFs).
- Fix the SC resource cleanup loop that iterated over secy.max
instead of sc.max.
====================
Link: https://patch.msgid.link/20260922102149.2078168-1-subratp@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The SC resource cleanup and statistics loops were incorrectly
iterating over secy.max instead of sc.max, so the highest SC id
could be left allocated across teardown or FLR. Use sc.max as
the loop bound.
Fixes: cfc14181d4 ("octeontx2-af: cn10k: mcs: Manage the MCS block hardware resources")
Signed-off-by: Baha Mesleh <baha.mesleh@nokia.com>
Signed-off-by: Subrat Pandey <subratp@marvell.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20260922102149.2078168-3-subratp@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Previously, BPID assignment under CONFIG_DCB assumed
`queue_to_pfc_map` was always initialized. For SDP VFs this leads to
invalid memory access as it was not initialized.
This patch adds a NULL check for `queue_to_pfc_map` before
dereferencing it. Also, simplifies the logic by always assigning a
default BPID first, then conditionally overriding it if CONFIG_DCB is
enabled and the map exists.
Fixes: 184fb40f73 ("octeontx2-pf: Avoid adding dcbnl_ops for LBK and SDP vf")
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Subrat Pandey <subratp@marvell.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20260922102149.2078168-2-subratp@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The mlx5_handle_changeupper_event() and mlx5_handle_changeinfodata_event()
functions check for LAG masters (which includes both bonding and team
devices) but only call bonding-specific APIs. When processing team device
events, calling bond_slave_get_rcu() and bond_is_slave_inactive() on
team_port structures causes KASAN to detect an out-of-bounds memory access
since team_port is smaller than bond slave.
Fix this by wrapping the bond-specific API calls with a check for bonding
devices. This allows the function to still process LAG events for both
bonding and teams but only calls bond-specific functions when dealing with
actual bonding devices.
For mlx5_handle_changeinfodata_event(), keep the explicit bond check as
mlx5 doesn't handle state information for team ports anyway.
Tested with Mellanox ConnectX-5 on Linux 7.2.0-rc6:
- Bonding: PASS (no regressions)
- Team device: PASS (no KASAN errors)
Fixes: 54493a08e2 ("net/mlx5: Lag, record inactive state of bond device")
Suggested-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Anirudh Virdi <avirdi@redhat.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Link: https://patch.msgid.link/20260924064244.94045-1-avirdi@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In UniMAC hardware, there is a 0xC byte gap between the RX MIB counters
and the TX MIB counters, and a second 0xC byte gap between the TX MIB
counters and the RX RUNT MIB counters.
In bcm_sysport_update_mib_counters(), 'offset' was only set to
UMAC_MIB_STAT_OFFSET (0xC) for all non-RX counters, omitting the second
0xC gap for BCM_SYSPORT_STAT_RUNT counters. As a result, all 4 RUNT MIB
counters were read from unmapped gap register space.
Fix this by setting offset to 2 * UMAC_MIB_STAT_OFFSET (0x18) when
reading BCM_SYSPORT_STAT_RUNT counters.
Fixes: 80105befdb ("net: systemport: add Broadcom SYSTEMPORT Ethernet MAC driver")
Reviewed-by: Nicolai Buchwitz <nb@tipi-net.de>
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20260922232440.598918-6-florian.fainelli@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When running on SYSTEMPORT Lite, certain statistics are unsupported and
skipped during bcm_sysport_get_stats(). The variable 'j' tracks the
compacted index into the destination data buffer, whereas 'i' iterates
over all elements in bcm_sysport_gstrings_stats.
Because the buffer allocated by ethtool is sized only according to
bcm_sysport_get_sset_count(), storing values at data[i] instead of
data[j] writes past the allocated array bounds, leading to memory
corruption.
Fix this by writing to data[j] instead of data[i].
Fixes: 10377ba767 ("net: systemport: Support 64bit statistics")
Reviewed-by: Nicolai Buchwitz <nb@tipi-net.de>
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20260922232440.598918-2-florian.fainelli@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Documentation/networking/dsa/b53.rst is not covered by the BROADCOM
B53/SF2 ETHERNET SWITCH DRIVER entry.
Signed-off-by: Christian Melendez <chrismelnu@gmail.com>
Link: https://patch.msgid.link/20260922211439.369917-2-chrismelnu@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
hci_low_sent() selects a connection under RCU but drops the read lock
before calculating its quota and returning it to the scheduler. The
connection is then used without lifetime protection by hci_sched_iso()
and hci_sched_sco().
After the TX worker drops the RCU read lock, hci_abort_conn_sync() on
hdev->req_workqueue can remove the connection from the hash, complete
synchronize_rcu(), purge its queues and release it. The TX worker on
hdev->workqueue can then access the freed connection in hci_quote_sent()
or while dequeuing packets and updating conn->sent.
KASAN reported:
BUG: KASAN: slab-use-after-free in hci_low_sent+0x730/0x840
Workqueue: hci0 hci_tx_work
Call Trace:
hci_low_sent+0x730/0x840
hci_sched_iso+0x25e/0x4d0
hci_tx_work+0x239/0xcb0
Allocated by task 93:
__hci_conn_add+0x16f/0x1b40
hci_bind_bis+0x782/0x17b0
hci_connect_bis+0xa0/0x510
iso_sock_connect+0x589/0x1050
Freed by task 88:
kfree+0x131/0x3c0
device_release+0xc8/0x240
kobject_put+0x14d/0x280
hci_conn_del+0x55a/0xe80
hci_disconnect_sync+0x156/0x180
hci_abort_conn_sync+0x3e7/0x940
hci_cmd_sync_work+0x13c/0x290
Hold hci_dev_lock() across connection selection and transmission in both
SCO and ISO scheduling, serializing them with connection teardown. This
also prevents queuing completion timestamps after the connection queues
have been purged. Extending RCU across transmission would be unsafe
because the transmit path can sleep. Keep the ISO timeout check outside
the mutex since hci_link_tx_to() takes it itself.
The preceding channel fix already holds this mutex in the ACL and LE
schedulers, which call the SCO scheduler between packets. Move the SCO
body to __hci_sched_sco(), assert that its caller holds the mutex, and
use it directly from these locked paths. Keep a locking hci_sched_sco()
wrapper for the direct calls from hci_tx_work(). This avoids recursively
acquiring the device mutex while preserving the scheduling order.
Remove the obsolete claim that connection removal disables TX.
Fixes: bf4c632524 ("Bluetooth: convert conn hash to RCU")
Cc: stable@vger.kernel.org
Assisted-by: LLM
Signed-off-by: Chengfeng Ye <nicoyip.dev@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
hci_chan_sent() selects a channel under RCU but drops the read lock before
accessing chan->conn and returning the channel. The ACL and LE schedulers
then use its packet queue and update its transmit counters without any
protection against channel deletion.
After TX selects a channel and releases RCU, a disconnect command timeout
on the separate request workqueue can run hci_conn_failed() and
l2cap_conn_del(). hci_chan_del() can then unlink the channel, complete
synchronize_rcu(), purge its queue and free it before TX resumes. This
causes use-after-free both in hci_chan_sent() and in its callers.
KASAN reported:
BUG: KASAN: slab-use-after-free in hci_chan_sent+0x892/0x9b0
Workqueue: hci0 hci_tx_work
Call Trace:
hci_chan_sent+0x892/0x9b0
hci_tx_work+0x5e6/0xb70
Allocated by task 91:
hci_chan_create+0xe3/0x350
l2cap_conn_add.part.0+0x12/0xa30
l2cap_chan_connect+0x110d/0x1b60
l2cap_sock_connect+0x310/0x530
Freed by task 99:
hci_chan_del+0x11f/0x170
l2cap_conn_del+0x4f1/0x800
l2cap_connect_cfm+0x88c/0xd30
hci_conn_failed+0x150/0x250
hci_abort_conn_sync+0x3e3/0x800
hci_cmd_sync_run+0x7e/0xc0
hci_abort_conn+0x105/0x1f0
disconnect_sync+0x157/0x290
hci_cmd_sync_work+0x13c/0x290
Hold the existing device mutex across channel selection and transmission
in both schedulers to serialize them with channel teardown. Keep timeout
handling outside the critical sections because hci_link_tx_to() acquires
the same mutex. This also permits the transmit path to sleep, unlike
extending the RCU read-side critical section across packet submission.
Fixes: 3eff45eaf8 ("Bluetooth: convert tx_task to workqueue")
Cc: stable@vger.kernel.org
Assisted-by: LLM
Signed-off-by: Chengfeng Ye <nicoyip.dev@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
build_pairing_cmd() looks up remote OOB data and copies its contents
without holding hdev->lock, which serializes the list's writers. After
SMP finds an entry, a concurrent management Remove Remote OOB Data
command can unlink and free it before SMP reads its present flag or
copies its random and confirmation values. Removal can also invalidate
an entry while the lookup is still traversing the list.
KASAN reported:
BUG: KASAN: slab-use-after-free in build_pairing_cmd+0x948/0x9b0
Call Trace:
build_pairing_cmd+0x948/0x9b0
smp_recv_cb+0x459f/0x8110
l2cap_recv_frame+0xf14/0x9190
l2cap_recv_acldata+0xa64/0xd40
hci_rx_work+0x4ca/0x730
Allocated by task 87:
hci_add_remote_oob_data+0x11d/0x530
add_remote_oob_data+0x282/0x400
hci_sock_sendmsg+0x1033/0x1ea0
Freed by task 93:
hci_remote_oob_data_clear+0x108/0x1c0
remove_remote_oob_data+0x198/0x220
hci_sock_sendmsg+0x1033/0x1ea0
Taking hdev->lock in build_pairing_cmd() would recurse for callers that
already hold it and invert the device-to-L2CAP lock order on the receive
path. Add a per-device remote_oob_lock instead, held across the SMP
lookup and copies and by the add, remove and clear helpers. Cover
initialization and in-place updates as well, so SMP cannot read partially
initialized or updated OOB values. Release the mutex on allocation
failure, preserving the existing error return.
The new critical sections acquire no device, connection or channel locks.
Writers retain their existing hdev->lock protection, which continues to
serialize the other readers without changing their locking or behavior.
Link: https://lore.kernel.org/r/00660cd3-7d71-13a4-f617-229e6defb701@gmail.com
Fixes: 02b05bd8b0 ("Bluetooth: Set SMP OOB flag if OOB data is available")
Cc: stable@vger.kernel.org
Signed-off-by: Chengfeng Ye <nicoyip.dev@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
For RFCOMM_RELEASE_ONHUP devices, rfcomm_tty_install() and
__rfcomm_release_dev() both use RFCOMM_TTY_OWNED to decide who drops the
initial tty_port reference. The release path tests the bit separately
from the install path setting it, so both can drop that reference.
The synchronous hangup does not prevent this race: port->tty is not
assigned until tty_port_open(), after installation. The following
interleaving is possible:
1. Install and release each obtain a reference with rfcomm_dev_get().
2. Release observes RFCOMM_TTY_OWNED clear.
3. Install sets RFCOMM_TTY_OWNED and drops the initial reference.
4. Release drops the same initial reference again.
5. TTY cleanup drops its reference and frees the device.
6. Release performs its final tty_port_put() on the freed port.
KASAN reported:
BUG: KASAN: slab-use-after-free in tty_port_put+0x22/0x190
Write of size 4 at addr ffff8881001d3d5c by task poc/92
Call Trace:
tty_port_put+0x22/0x190
rfcomm_dev_ioctl+0x1d4/0x1930
sock_do_ioctl+0x110/0x260
sock_ioctl+0x380/0x590
__x64_sys_ioctl+0x134/0x1c0
Allocated by task 88:
rfcomm_dev_ioctl+0x8f6/0x1930
sock_do_ioctl+0x110/0x260
sock_ioctl+0x380/0x590
__x64_sys_ioctl+0x134/0x1c0
Freed by task 65:
kfree+0x131/0x3c0
rfcomm_dev_destruct+0x23b/0x2f0
release_one_tty+0xc1/0x370
process_one_work+0x661/0x1090
Use test_and_set_bit() in both paths so that only the caller that changes
RFCOMM_TTY_OWNED from clear to set drops the initial reference. Each path
keeps its own lookup reference until release or TTY cleanup, preserving
the existing callback ordering and error handling.
Fixes: 80ea73378a ("Bluetooth: Fix unreleased rfcomm_dev reference")
Cc: stable@vger.kernel.org
Assisted-by: LLM
Signed-off-by: Chengfeng Ye <nicoyip.dev@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The sync command worker holds hdev->req_lock, but inquiry-cache updates
and flushes use hdev->lock. Both hci_acl_create_conn_sync() and
hci_stop_discovery_sync() look up entries and read their fields without
taking hdev->lock.
After either lookup returns, a concurrent HCIINQUIRY ioctl can acquire
hdev->lock and flush the cache, freeing the entry. The worker then reads
the freed entry while preparing a create-connection or remote-name-cancel
command. The list traversal also races with cache updates and removal.
KASAN reported these accesses:
BUG: KASAN: slab-use-after-free in hci_acl_create_conn_sync+0x5f1/0x650
Workqueue: hci0 hci_cmd_sync_work
Call Trace:
hci_acl_create_conn_sync+0x5f1/0x650
hci_cmd_sync_work+0x13c/0x290
Allocated by task 90:
hci_inquiry_cache_update+0x3e6/0x7d0
hci_inquiry_result_evt+0x3cb/0x560
Freed by task 93:
hci_inquiry_cache_flush+0x111/0x2b0
hci_inquiry+0x2f2/0x780
hci_sock_ioctl+0x269/0x5f0
BUG: KASAN: slab-use-after-free in hci_stop_discovery_sync+0x3b1/0x3c0
Workqueue: hci0 hci_cmd_sync_work
Call Trace:
hci_stop_discovery_sync+0x3b1/0x3c0
hci_cmd_sync_work+0x173/0x300
Allocated by task 86:
hci_inquiry_cache_update+0x483/0x940
hci_inquiry_result_evt+0x3cb/0x560
Freed by task 91:
hci_inquiry_cache_flush+0x13e/0x2f0
hci_inquiry+0x2f2/0x780
hci_sock_ioctl+0x269/0x5f0
Hold hdev->lock across each lookup and all reads from its result. Copy the
remote address before unlocking so discovery cancellation does not retain
a cache entry pointer. Release the lock before sending synchronous HCI
commands, since their completion handlers may need the same lock.
Fixes: cf75ad8b41 ("Bluetooth: hci_sync: Convert MGMT_SET_POWERED")
Fixes: 45340097ce ("Bluetooth: hci_conn: Only do ACL connections sequentially")
Cc: stable@vger.kernel.org
Signed-off-by: Chengfeng Ye <nicoyip.dev@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
hci_unregister_dev() disables cmd_work and cmd_timer, then calls
hci_cmd_sync_clear(), whose cancel_work_sync() waits for
hci_cmd_sync_work() to return. That worker dequeues and runs every
entry on cmd_sync_work_list. With cmd_work disabled nothing reaches
the controller, so each queued HCI command waits the full
HCI_CMD_TIMEOUT (2s).
The backlog has no bound. Userspace can keep queuing MGMT commands
such as MGMT_OP_GET_CLOCK_INFO against a controller that doesn't
answer. Closing /dev/vhci then blocks in vhci_release() for
backlog * 2s:
INFO: task syz-executor:5749 blocked for more than 143 seconds.
cancel_work_sync
hci_cmd_sync_clear
hci_unregister_dev
vhci_release
In a local reproduction the backlog held more than 5000 entries,
which comes to hours of hang.
Stop the worker from taking new entries once HCI_UNREGISTER is set,
and wake any request still waiting with -ENODEV before cancelling
the work. The entries left over are destroyed with -ECANCELED by the
existing sweep in hci_cmd_sync_clear(). They stay on the list until
the work has stopped, so hci_cmd_sync_dequeue() and friends still see
them. A callback already running may still issue another command,
which delays unregister by at most one timeout per remaining command,
not by the whole backlog.
Fixes: 008ee9eb8a ("Bluetooth: hci_sync: Fix not processing all entries on cmd_sync_work")
Reported-by: syzbot+217e3f1283cafe80586e@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=217e3f1283cafe80586e
Signed-off-by: Nguyen Ngoc Thang <ngocthang2710.1999@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The fragmented path in hci_queue_iso() calls __skb_queue_tail() without
holding conn->data_q.lock. The socket lock serializes senders, but the
transmit worker can concurrently remove packets from this queue using
skb_dequeue().
After an insertion saves the old tail pointer, hci_sched_iso() can dequeue
that packet and pass it to the driver. The driver can free the packet
before the insertion resumes and writes to the old tail's next pointer,
causing a use-after-free. Concurrent updates can also corrupt the queue.
KASAN reported:
BUG: KASAN: slab-use-after-free in hci_send_iso+0xc7d/0xe10
Call Trace:
hci_send_iso+0xc7d/0xe10
iso_sock_sendmsg+0x710/0x900
__sys_sendto+0x34a/0x3a0
Allocated by task 86:
__alloc_skb+0xdd/0x820
alloc_skb_with_frags+0x7e/0x770
sock_alloc_send_pskb+0x67a/0x820
bt_skb_sendmsg.constprop.0+0xc0/0x6c0
iso_sock_sendmsg+0x44e/0x900
Freed by task 90:
kmem_cache_free+0xcb/0x3d0
vhci_read+0x33f/0x4d0
vfs_read+0x177/0xa20
Hold the queue lock across the entire fragment batch, as hci_queue_acl()
does, to serialize insertion against dequeue while preserving fragment
ordering.
Fixes: 26afbd826e ("Bluetooth: Add initial implementation of CIS connections")
Cc: stable@vger.kernel.org
Signed-off-by: Chengfeng Ye <nicoyip.dev@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Bluetooth: hci_conn: Lock parent access during enhanced SCO setup
hci_enhanced_setup_sync() runs on the request workqueue without the
hci_dev_lock held by its caller when setup was queued. Its CVSD
capability check and find_next_esco_param() dereference conn->parent
while the receive workqueue can unlink and release that parent.
The following interleaving can cause a use-after-free:
hci_enhanced_setup_sync() hci_disconn_complete_evt()
load conn->parent
hci_dev_lock()
hci_conn_del(ACL parent)
unlink SCO child
drop link's parent reference
clear child->parent
release ACL parent
bt_link_release()
kfree(parent)
hci_dev_unlock()
read parent->features[0][3]
The reference held for the queued SCO child does not keep its ACL parent
alive after unlinking. Commit 42de40abe2 ("Bluetooth: hci_conn: fix the
SCO setup context lifetime") protects the child stored in the queued
context, but leaves these parent accesses unprotected.
With a 40 ms diagnostic delay after loading conn->parent, an instrumented
kernel based on fd179f8a05, which already contains 42de40abe2,
reported:
BUG: KASAN: slab-use-after-free in hci_enhanced_setup_sync+0xda5/0xdf0
Read of size 1 at addr ffff888102204047 by task kworker/u17:0/93
Call Trace:
hci_enhanced_setup_sync+0xda5/0xdf0
hci_cmd_sync_work+0x13c/0x290
process_one_work+0x6b4/0x10e0
Allocated by task 92:
__hci_conn_add+0x304/0x1df0
hci_connect_acl+0x349/0x3e0
hci_connect_sco+0x3b/0x9a0
sco_sock_connect+0x475/0xca0
Freed by task 94:
kfree+0x121/0x3c0
bt_link_release+0x79/0xa0
device_release+0xc8/0x240
kobject_put+0x14d/0x280
hci_conn_del+0x524/0xe30
hci_disconn_complete_evt+0x403/0x8c0
hci_event_packet+0x71b/0xb20
hci_rx_work+0x293/0x730
The accessed address is 71 bytes into the freed ACL parent, at its
features[0][3] byte; the queued SCO child is a different object. The
diagnostic preserves the loaded parent across the delay, matching the
unmodified compiled capability check, and does not change the parent
references or teardown path.
Hold hci_dev_lock() across the codec switch, including every call to
find_next_esco_param(), and release it on all selection errors. Keep
configure_datapath_sync() outside the critical section because it waits
for HCI events. Preserve parameter selection and existing return values.
Fixes: e07a06b4eb ("Bluetooth: Convert SCO configure_datapath to hci_sync")
Cc: stable@vger.kernel.org
Assisted-by: GPT-6-Astra
Signed-off-by: Chengfeng Ye <nicoyip.dev@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
modify_prefix_route() is given the lifetime in clock_t relative to now,
but fib6_set_expires() wants an absolute jiffies value. So when a
permanent address is changed to a finite valid_lft, the prefix route
ends up already expired and GC removes it.
Steps to reproduce:
ip link add dummy9 type dummy
ip link set dummy9 up
ip -6 addr add 2001:db8:9::1/64 dev dummy9
ip -6 addr change 2001:db8:9::1/64 dev dummy9 valid_lft 3600 preferred_lft 3600
ip -6 route show dev dummy9 # expires is negative
Fixes: 8308f3ff17 ("net/ipv6: Add support for specifying metric of connected routes")
Signed-off-by: Qishuai Liu <lqs@lqs.me>
Reviewed-by: Hangbin Liu <liuhangbin@kylinos.cn>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Link: https://patch.msgid.link/20260923132048.3272878-1-lqs@lqs.me
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since the page_pool conversion every RX buffer is a whole page and the
skb truesize is the page, although the hardware writes at most 2 KiB of
it. On 64 KiB pages a packet therefore counts 65792 bytes against the
socket buffer where it used to count 2752. As a result a UDP socket
with the default buffer starts to drop after three packets, and the RX
rings pin 16 MiB for 512 KiB of buffers.
Fix this and allocate the buffers as page fragments, so the truesize is
what a packet occupies. 4 KiB pages stay one buffer per page.
Sync each buffer in the refill path, as page_pool can only sync a whole
page on recycle. On 4 KiB pages that is twice what the hardware wrote.
Fixes: 7bc054c2d4 ("net: bcmgenet: convert RX path to page_pool")
Reported-by: Karl Mehltretter <kmehltretter@gmail.com>
Closes: https://lore.kernel.org/all/20260924065839.56793-1-kmehltretter@gmail.com/
Signed-off-by: Nicolai Buchwitz <nb@tipi-net.de>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20260924101922.2675127-1-nb@tipi-net.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Two racing tc filter add requests on the same chain/prio of an
unlocked classifier both run change() on the shared proto and both
can fail: the winner's tcf_chain_tp_delete_empty() attempt gives up
because the loser's handle is still in the idr, and the loser's
error path drops only its own reference without a second reclamation
attempt. The empty proto stays linked in the chain, holding the
chain reference, a block reference and the classifier module
reference until the chain or block is torn down.
Reclaim the proto on the error path of any failed request that holds
a proto reference. The reclamation is emptiness-gated:
tcf_chain_tp_delete_empty() unlinks the proto only when
delete_empty() admits it is empty, so a live shared proto is never
unlinked. A proto the request created is reclaimed unconditionally -
it is the only owner, so marking it for deletion is safe even without
a delete_empty callback. Classifiers without one (the check marks the
proto unconditionally) are rtnl-serialized, so the raced window this
guard closes cannot arise for them.
This is a follow-up to commit d4e359b360 ("net/sched: cls_api: fix
teardown of an adopted proto on insert-race loss"), which stopped the
loser of the insert race from unlinking the winner's live proto but
left the empty-proto residual in place.
Conditions to recreate:
- CONFIG_NET_CLS_FLOWER=y; veth pair
- tc qdisc add dev veth0 ingress
- two concurrent `tc filter add dev veth0 ingress protocol ip pref 1
flower skip_sw ... action drop` (both fail in fl_hw_replace_filter
after publishing their handle in the idr); repeat in a loop
- an empty flower tp stays linked after both requests fail; visible
as a bare `filter protocol ip pref 1 flower chain 0` header in
`tc filter show` with no filter entries
- CAP_NET_ADMIN (namespace-local via unshare -Urn suffices)
Fixes: 8b64678e0a ("net: sched: refactor tp insert/delete for concurrent execution")
Reported-by: Sashiko (nipa) <sashiko-bot@kernel.org>
Closes: https://netdev-ai.bots.linux.dev/sashiko/#/patchset/20260805134049.927864-1-victor@mojatatu.com
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/QDISC-JCOT.v1.20260910090924@mojatatu.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
mctp_add_dev() links the new mctp_dev into dev->mctp_ptr before mdev->dev
is assigned, so a reader that picks the device up in that window
dereferences a net_device pointer that is still NULL:
KASAN: null-ptr-deref in range [0x00000000000000b0-0x00000000000000b7]
Call Trace:
<TASK>
? __pfx_mctp_sendmsg (./include/linux/sockptr.h:49)
? __pfx_mctp_dst_output (net/mctp/route.c:41)
? selinux_socket_sendmsg (security/selinux/hooks.c:5278)
____sys_sendmsg (net/socket.c:775 (discriminator 1) net/socket.c:790
(discriminator 1) net/socket.c:2684 (discriminator 1))
? __pfx_____sys_sendmsg (net/socket.c:1131)
? __pfx_copy_msghdr_from_user (net/socket.c:2590)
? update_cfs_rq_load_avg (kernel/sched/fair.c:5478)
___sys_sendmsg (net/socket.c:2738)
? __pfx____sys_sendmsg (net/socket.c:2625)
? perf_event_task_tick (./include/linux/rcupdate.h:838)
? sched_tick (kernel/sched/core.c:5818)
? clockevents_program_event (kernel/time/clockevents.c:372)
? fdget (./include/linux/rcupdate.h:873 fs/file.c:1100)
__sys_sendmsg (net/socket.c:2770)
? __pfx___sys_sendmsg (net/socket.c:2751)
do_syscall_64 (arch/x86/entry/syscall_64.c:63)
entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:121)
</TASK>
Fix by publishing only once the object is fully initialised:
__mctp_dev_get() runs under rcu_read_lock() only and hands
this object to readers as soon as mctp_ptr is assigned, so
they must never observe mdev->dev == NULL.
Fixes: 583be982d9 ("mctp: Add device handling and netlink interface")
Signed-off-by: Binbin Deng <18983559317@163.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/729830b8.130.1a0c945579d.Coremail.18983559317@163.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Every week in this release is record-setting for number of posted
patches. It doesn't seem like we're creating any regressions with
all these fixes, 3 Fixes tags here point to 7.2 commits but none
are true regression fixes. We're trying to keep the count down,
nonetheless.
Previous releases - regressions:
- net: don't require the hwtstamp NDOs when a PHY provides timestamping
- ipv6: fix dst leak for uncached routes
- vrf: stop corrupting skb->csum when capturing CHECKSUM_COMPLETE
packets
Previous releases - always broken:
- packet: use ubuf_info completion for TX_RING packets
- arp: terminate device name before lookup
- ipv6: do not let ipv6_find_hdr() return an offset past the packet end
- udp: remove a disconnected socket from the 4-tuple hash table
- sctp: discard the rest of the packet on a stale-cookie error
- eth: mlx5: Bridge, fix remaining switchdev ownership gaps on merged
eswitch
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=YiiK
-----END PGP SIGNATURE-----
Merge tag 'net-7.3-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from Bluetooth, NFC and Netfilter.
Every week in this release is record-setting for number of posted
patches. It doesn't seem like we're creating any regressions with all
these fixes, three 'Fixes' tags here point to 7.2 commits but none are
true regression fixes. We're trying to keep the count down,
nonetheless.
Previous releases - regressions:
- net: don't require the hwtstamp NDOs when a PHY provides
timestamping
- ipv6: fix dst leak for uncached routes
- vrf: stop corrupting skb->csum when capturing CHECKSUM_COMPLETE
packets
Previous releases - always broken:
- packet: use ubuf_info completion for TX_RING packets
- arp: terminate device name before lookup
- ipv6: do not let ipv6_find_hdr() return an offset past the packet
end
- udp: remove a disconnected socket from the 4-tuple hash table
- sctp: discard the rest of the packet on a stale-cookie error
- eth: mlx5: Bridge, fix remaining switchdev ownership gaps on merged
eswitch"
[ And lots of other random network driver fixes ]
* tag 'net-7.3-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (189 commits)
tcp: prevent collapsing skbs across boundary in rtx queue
vlan: ensure sufficient headroom in vlan_dev_hard_header()
net/sched: sch_teql: fix shadowed err in __teql_resolve()
bridge: check llc_mac_hdr_init() return value in br_send_bpdu()
llc: fix skb UAF and leaks on llc_mac_hdr_init() failure
llc: reserve device headroom for allocated frames
gve: DQO: reject TSO packets with an out of range MSS
gve: fix TX drop when GSO MSS is too small for hw
gve: DQO: fix header length used by gve_can_send_tso() for UDP GSO
net: flush skb_defer_nodes in dev_cpu_dead()
net: ethernet: stmmac: dwmac-rk: fix bulk clock leak when the PHY clock fails
af_packet: fix integer overflow in prb_calc_retire_blk_tmo()
tipc: Fix a data race on mon->peer_cnt in mon_timeout()
net: phy: intel-xway: workaround 100BASE-TX Link-Up issue
net/smc: fix UAF on lgr list traversal in smcr_port_err()
net/rds: size a connection's path set by the transport it ends up with
nfp: hold IPsec RX state under the XArray lock
net: ena: fix MMIO read buffer leak on probe failure
net: ena: fix PHC cleanup on probe failure
net/sched: act_ct: fix helper UAF due to extensions realloc
...
tcp_write_collapse_fence() sets TCP_SKB_CB(skb)->eor = 1 on
tcp_write_queue_tail(sk) to prevent skbs queued after a switch to
device encryption from being collapsed into earlier skbs.
The fence is a no-op if all earlier data has already been transmitted
when the switch happens: sk->sk_write_queue is empty. The not yet
acknowledged earlier skbs wait in sk->tcp_rtx_queue with eor 0.
On a subsequent retransmit or SACK shift, tcp_retrans_try_collapse() or
tcp_shift_skb_data() can then merge an skb queued after the switch into
one queued before it.
Both users of the fence are affected:
- psp: devices only encrypt skbs with skb->decrypted set. The merged skb
keeps decrypted = 0 from the earlier skb, so merged data sent after
psp_sock_assoc_set_tx() is retransmitted in cleartext.
- tls device offload: the merged skb straddles the start marker set in
tls_set_device_offload(). The software fallback (fill_sg_in() returns
-EINVAL) and the mlx5, nfp and funeth drivers cannot handle such an
skb and drop it. Every retransmit rebuilds the same skb, so the
connection stalls.
Fix this in two places, for defense in depth:
1. Fall back to tcp_rtx_queue_tail(sk) in tcp_write_collapse_fence()
when tcp_write_queue_tail(sk) is NULL.
2. Check !skb_cmp_decrypted(to, from) in tcp_skb_can_collapse(), as
tcp_skb_can_collapse_rx() does on receive. skb_shift(), which both
collapse paths call, already has a DEBUG_NET_WARN_ON_ONCE() for this
condition.
Fixes: e8f6979981 ("net/tls: Add generic NIC offload infrastructure")
Cc: stable@vger.kernel.org
Signed-off-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Daniel Zahka <daniel.zahka@gmail.com>
Link: https://patch.msgid.link/20260924154427.953800-1-willemdebruijn.kernel@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Eric Dumazet says:
====================
vlan: ensure sufficient headroom in vlan_dev_hard_header()
Callers that only reserve ETH_HLEN or less, or skbs allocated before
dynamic device/headroom changes (such as toggling VLAN_FLAG_REORDER_HDR
or bonding/team switching slaves), can reach vlan_dev_hard_header() with
insufficient headroom and trigger skb_under_panic().
When vlan_dev_hard_header() returns -ENOMEM upon skb_cow_head() failure,
a few callers of dev_hard_header() / llc_mac_hdr_init() had pre-existing
error-handling bugs:
====================
Link: https://patch.msgid.link/20260924082951.1599377-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Callers that only reserve ETH_HLEN or less (such as llc_alloc_frame()),
or skbs allocated before dynamic device/headroom changes (e.g. toggling
VLAN_FLAG_REORDER_HDR or bonding/team switching slaves), can reach
vlan_dev_hard_header() with insufficient headroom and trigger
skb_under_panic().
Use skb_cow_head() in vlan_dev_hard_header() when VLAN_FLAG_REORDER_HDR
is not set to ensure sufficient headroom for the VLAN header(s) and the
underlying device hard header.
Use READ_ONCE() to read dev->hard_header_len and dev->needed_headroom as
they can be updated concurrently under RTNL (e.g. in
vlan_transfer_features()) while vlan_dev_hard_header() runs locklessly on
the transmit path. Also avoid LL_RESERVED_SPACE(dev) here so that the
extra HH_DATA_MOD alignment padding does not trigger unnecessary
pskb_expand_head() reallocations on inner stacked VLAN devices after the
outer VLAN header has been pushed.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Reported-by: Zixuan Chai <petalzu987@gmail.com>
Closes: https://lore.kernel.org/netdev/cover.1789987105.git.petalzu987@gmail.com/
Link: https://lore.kernel.org/netdev/179022851638.2160803.1808206741379444999@kernel.org/
Cc: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20260924082951.1599377-5-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
__teql_resolve() declares an inner 'int err;' inside the
'if (neigh_event_send(n, skb_res) == 0)' block, shadowing the outer
'int err = 0;'. As a result, a negative return from dev_hard_header()
is written to the inner variable and __teql_resolve() still returns 0.
Remove the shadowed variable and set the outer err to -EINVAL when
dev_hard_header() returns a negative error.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Closes: https://lore.kernel.org/netdev/179022851638.2160803.1808206741379444999@kernel.org/
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20260924082951.1599377-4-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In llc_conn_ac_resend_i_xxx_x_set_0_or_send_rr(), if llc_mac_hdr_init()
fails, kfree_skb(skb) is called instead of kfree_skb(nskb). This leaks
the newly allocated nskb, reads from the freed skb via LLC_I_GET_NR(pdu),
and double-frees skb when llc_conn_state_process() drops its reference.
In llc_sap_action_send_xid_r() and llc_sap_action_send_test_r(), nskb is
leaked if llc_mac_hdr_init() returns an error.
Free nskb in all three error paths.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Closes: https://lore.kernel.org/netdev/179022851638.2160803.1808206741379444999@kernel.org/
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20260924082951.1599377-2-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
llc_alloc_frame() reserves link-layer headroom using the device type.
This is insufficient for stacked Ethernet devices such as VLAN devices,
where vlan_dev_hard_header() pushes a VLAN header before the lower
device's Ethernet header. An LLC response on such a device can
therefore underflow skb headroom in eth_header().
Use LL_RESERVED_SPACE() to account for the device's actual required
headroom while preserving the existing LLC device-type check.
Fixes: bf9ae5386b ("llc: use dev_hard_header")
Cc: stable@vger.kernel.org
Reported-by: VEGA <vega@nebusec.ai>
Signed-off-by: Zixuan Chai <petalzu987@gmail.com>
Signed-off-by: Ren Wei <weir@nebusec.ai>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20260924012613.2533934-1-weir@nebusec.ai
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Eric Dumazet says:
====================
gve: DQO: fix handling of out of range TSO MSS
The DQO TX path assumes that the MSS of a TSO packet is within the
range supported by the device, [88, 9728].
This holds for locally generated traffic, but not for packets coming
from a tap or from a packet socket: virtio_net_hdr_to_skb() takes
gso_size from user space and only enforces a minimum, layer 2
forwarding does not check the MTU of GSO packets, and
gso_features_check() bounds skb->len and gso_segs but never gso_size.
Patch 1, from Eddie Phillips, deals with the lower bound. It moves the
existing test out of gve_prep_tso() into gve_features_check_dqo(), so
that these packets are segmented in software instead of being dropped.
Patch 2 deals with the upper bound, which is currently not checked at
all. gve_tx_fill_tso_ctx_desc() stores gso_size into a 14 bits wide
field, so that an MSS of 16384 silently becomes zero. Falling back to
software segmentation is not an option here, because skb_segment()
splits at gso_size regardless of the MTU, and would only replace an
invalid TSO packet by non TSO packets larger than the 9728 bytes the
device supports. These packets are dropped instead.
As noted in patch 2, oversized non TSO packets can still reach the
device whenever the stack segments in software. This is not specific
to gve and is better fixed in the core, so a patch for
__is_skb_forwardable() will be sent separately for net-next.
====================
Link: https://patch.msgid.link/20260924004252.1196328-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
gve_prep_tso() notes that the device requires the MSS to be <= 9728,
but does not enforce it, assuming the 9K MTU enforced by the hypervisor
and the 64KB limit on TSO sizes are enough.
This does not hold for packets that were not generated locally.
A guest behind a tap, or any packet socket user, can provide an
arbitrary gso_size in virtio_net_hdr. Layer 2 forwarding does not check
the MTU for GSO packets (is_skb_forwardable()), and gso_features_check()
only bounds skb->len and gso_segs, never gso_size.
Such a packet reaches gve_tx_fill_tso_ctx_desc(), which puts gso_size
into the mss field of the TSO context descriptor. This field is 14 bits
wide, so a gso_size of 16384 is silently turned into an MSS of zero.
Drop these packets from gve_prep_tso(), and make sure that
gve_features_check_dqo() leaves their GSO bits alone: skb_segment()
splits at gso_size regardless of the MTU, so falling back to software
segmentation would give the device non TSO packets bigger than the
9728 bytes it supports.
Note that the device can still be given oversized non TSO packets when
the stack segments in software for other reasons, for instance after
TSO has been disabled with ethtool. This is a generic issue, because
the MTU check is skipped for GSO packets in the forwarding path, and
is addressed separately.
Fixes: a57e5de476 ("gve: DQO: Add TX path")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Harshitha Ramamurthy <hramamurthy@google.com>
Link: https://patch.msgid.link/20260924004252.1196328-3-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The device has a strict requirement that the minimum MSS
(gso_size) for TSO/GSO packets must be at least 88 bytes. If a packet
below this threshold is pushed to the hardware, it can cause
hardware to silently drop the packet, leading to increased latency
and retransmissions.
Currently, this is validated too late in the transmit pipeline
(gve_prep_tso), leading to silent drops.
Fix this by moving the validation into the .ndo_features_check
callback (gve_features_check_dqo). If we detect a GSO packet with
a gso_size smaller than GVE_TX_MIN_TSO_MSS_DQO, we clear the GSO
feature flags for this packet.
Fixes: a57e5de476 ("gve: DQO: Add TX path")
Signed-off-by: Eddie Phillips <eddiephillips@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Harshitha Ramamurthy <hramamurthy@google.com>
Link: https://patch.msgid.link/20260924004252.1196328-2-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----
iIYEABYKAC4WIQSVyBthFV4iTW/VU1/l49DojIL20gUCarVI0xAcbWljQGRpZ2lr
b2QubmV0AAoJEOXj0OiMgvbSEVgA+gNbC9CVCbCo0oufZbVpQwlwtuuEKEVpvxZx
q7oFYKCsAP9svCujGCXRHOmWhAAwe+wpXNb43l8coFn+pCfA8x3fCw==
=NOli
-----END PGP SIGNATURE-----
Merge tag 'landlock-7.3-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/mic/linux
Pull Landlock fixes from Mickaël Salaün:
"This mainly fixes the Landlock tracepoint support merged this cycle so
that denial and rule events report the intended policy context,
whether through tracefs or BTF-visible callbacks.
The size of this all is mainly from propagating the corrected contract
through event definitions and producers, adding new tests for the
reported context, and updating the documentation.
Also improve annotation and fix a GCC 16 build warning"
* tag 'landlock-7.3-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/mic/linux:
landlock: Widen ruleset versions to 64 bits
landlock: Add counted_by in landlock_domain
landlock: Fix tracepoint contract documentation
selftests/landlock: Test network denial context
selftests/landlock: Test filesystem denial blockers
landlock: Report the effective signal number
landlock: Report the actual ptrace tracer
landlock: Fix network denial trace context
landlock: Fix rule tracepoint context
landlock: Fix filesystem denial blocker reporting
landlock: Fix tracepoint fixed-width type names
landlock: Work around gcc-16 -Wuninitialized warning
gve_can_send_tso() computes how many buffers each segment of a GSO
packet would span, and for this it needs the length of the headers
that the device replicates in front of every segment.
It unconditionally uses skb_tcp_all_headers(), which reads the doff
field of the TCP header. SKB_GSO_UDP_L4 packets have no TCP header:
tcp_hdrlen() then reads one byte of the UDP payload, and header_len
can be anything in [0, 60] instead of the transport offset plus the
eight bytes of the UDP header that gve_prep_tso() programs into the
TSO context descriptor.
A wrong header length shifts all the segment boundaries computed in
the loop, so the number of buffers per segment can be over or under
estimated. In the first case, GSO is needlessly disabled for this
packet by gve_features_check_dqo() and the stack has to segment it.
In the second case, the driver hands the device a packet whose
segments span more than GVE_TX_MAX_DATA_DESCS buffers.
Use the UDP header length for SKB_GSO_UDP_L4 packets, matching what
gve_prep_tso() does.
Fixes: 014c607f86 ("gve: add support for UDP GSO for DQO format")
Closes: https://lore.kernel.org/netdev/CANn89i+MS4L60sFQ49=-f-mibeveUfcrpVkD5X+Qy6SOnEpd6w@mail.gmail.com/
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Ankit Garg <nktgrg@google.com>
Cc: Harshitha Ramamurthy <hramamurthy@google.com>
Cc: Joshua Washington <joshwash@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Reviewed-by: Ankit Garg <nktgrg@google.com>
Reviewed-by: Harshitha Ramamurthy <hramamurthy@google.com>
Link: https://patch.msgid.link/20260923145942.731365-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When a CPU goes offline, dev_cpu_dead() drains its softnet queues
(completion_queue, output_queue, poll_list, process_queue, and
input_pkt_queue), but leaves net_hotdata.skb_defer_nodes untouched.
If oldcpu goes offline while holding pending skbs in its
skb_defer_nodes lists (e.g. below the sysctl_skb_defer_max >> 1 IPI
threshold, or if the IPI races with CPU teardown), those skbs remain
stranded until oldcpu is brought back online. If any of these skbs
hold page_pool fragments, page_pool_destroy() will stall indefinitely
waiting for inflight pages to be returned when a netdev or driver is
torn down while oldcpu is offline.
Additionally, if smp_call_function_single_async() fails in
kick_defer_list_purge() because the target CPU went offline, reset
defer_ipi_scheduled to 0 so future IPI kicks are not blocked when the
CPU comes back online.
Also, if oldcpu was the last online CPU on its NUMA node, drain that
node's slot across all CPUs so no skbs deferred from that node remain
stranded on idle remote CPUs (or if the node itself is subsequently
offlined).
Finally, in skb_attempt_defer_free(), re-check cpu_online(cpu) and
whether the caller migrated CPUs after llist_add(), flushing the node
list if so, to close the preemption TOCTOU race against CPU/node
teardown.
Fixes: 68822bdf76 ("net: generalize skb freeing deferral to per-cpu lists")
Fixes: 5628f3fe3b ("net: add NUMA awareness to skb_attempt_defer_free()")
Closes: https://lore.kernel.org/netdev/20260916003430.3612956-1-kris.pan@intel.com/
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Kris Pan <kris.pan@intel.com>
Link: https://patch.msgid.link/20260923130318.607255-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
gmac_clk_enable() enables the bulk clocks first and then the optional
PHY clock. If clk_prepare_enable() on the PHY clock fails, the function
returns without rolling back the bulk clocks, and bsp_priv->clk_enabled
stays false, so the later gmac_clk_enable(bsp_priv, false) becomes a
no-op and the bulk clock references are leaked.
Add the missing clk_bulk_disable_unprepare() on that failure path.
Fixes: ea449f7fa0 ("net: ethernet: stmmac: dwmac-rk: rework optional clock handling")
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Lorenzo Bianconi <lorenzo.bianconi@oss.qualcomm.com>
Signed-off-by: Coia Prant <coiaprant@gmail.com>
Link: https://patch.msgid.link/20260923123713.3137146-1-coiaprant@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
prb_calc_retire_blk_tmo() computes in 32-bit int arithmetic:
mbits = (blk_size_in_bytes * 8) / (1024 * 1024);
If I'm reading the validation right, tp_block_size is user
controlled and packet_set_ring() only rejects values that are <= 0
as int or not page aligned, so a 256MiB block goes right through
(and alloc_one_pg_vec_page() even has a vzalloc fallback for it).
0x10000000 * 8 wraps to INT_MIN, and on a NIC reporting 1 Gbps
(div == 1) the function ends up returning -2047.
The condition is actually (8 * size) mod 2^32 >= 2^31 && div == 1,
so the trigger set is [256,512), [768,1024), [1280,1536) and
[1792,2048) MiB. Other sizes wrap to non-negative values and faster
links divide the unsigned value back below 2^31, which is why this
doesn't blow up for everyone.
What makes it fatal is what happens next in init_prb_bdqc():
p1->interval_ktime = ms_to_ktime(prb_calc_retire_blk_tmo(...));
hrtimer_start(&p1->retire_blk_timer, p1->interval_ktime,
HRTIMER_MODE_REL_SOFT);
A negative relative timeout expires immediately. The callback
unconditionally returns HRTIMER_RESTART, and hrtimer_forward() turns
the negative interval into hrtimer_resolution:
if (interval < hrtimer_resolution)
interval = hrtimer_resolution;
So the SOFT timer re-fires at the maximum rate forever, holding
sk_receive_queue.lock each pass. One CPU spins in softirq until the
socket is closed. Repeat with more rings and the machine is gone.
The overflow itself is ancient - it was introduced together with
TPACKET_V3 in f6fb8f100b ("af-packet: TPACKET_V3 flexible buffer
implementation."). Its effect prior to f7460d2989 ("net:
af_packet: Use hrtimer to do the retire operation", v6.18) was not
as clear-cut, though: the return value was stored into an unsigned
short retire_blk_tov, so a negative result was truncated, and a
0-jiffy delay loop could be programmed as well. Neither is nearly
as detrimental as the immediate maximum-rate spin the hrtimer
conversion turned it into.
(Unrelated to CVE-2019-20812 - that one was the ethtool failure path
returning 0, which now returns DEFAULT_PRB_RETIRE_TOV.)
Reproducer, needs CAP_NET_RAW (a --network host container has it by
default) and a 1 Gbps NIC (QEMU e1000 works):
int fd = socket(AF_PACKET, SOCK_RAW, htons(ETH_P_ALL));
bind(fd, ...);
int v = TPACKET_V3;
setsockopt(fd, SOL_PACKET, PACKET_VERSION, &v, sizeof(v));
struct tpacket_req3 req = {
.tp_block_size = 0x10000000,
.tp_block_nr = 1,
.tp_frame_size = 2048,
.tp_frame_nr = 0x10000000 / 2048,
.tp_retire_blk_tov = 0,
};
setsockopt(fd, SOL_PACKET, PACKET_RX_RING, &req, sizeof(req));
Compute in 64 bits instead. The operands are already bounded by the
existing validation, so nothing else changes. If you'd prefer a
different fix, just say so and I'll respin.
Fixes: f6fb8f100b ("af-packet: TPACKET_V3 flexible buffer implementation.")
Cc: stable@vger.kernel.org
Signed-off-by: Dairui Zhang <zhangdairui@gmail.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://patch.msgid.link/20260923050101.1510064-1-zhangdairui@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
mon_timeout() evaluates dom_size(mon->peer_cnt) before it takes mon->lock,
while mon->peer_cnt is updated under that lock by tipc_mon_add_peer() and
tipc_mon_remove_peer(). The value can therefore be stale, and the decision
whether the local domain has to be recomputed can be based on an outdated
member count.
Read mon->peer_cnt inside the write_lock_bh(&mon->lock) protected region.
Fixes: 35c55c9877 ("tipc: add neighbor monitoring framework")
Signed-off-by: Ginger Li <ginger.jzllee@gmail.com>
Reviewed-by: Tung Nguyen <tung.quang.nguyen@est.tech>
Link: https://patch.msgid.link/20260922080909.21123-1-ginger.jzllee@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
MaxLinear GSW12x/GSW14x Ethernet Switch Errata Sheet states:
"An issue has been sporadically observed after device power-on on the first
link-up attempt in 100BASE-TX mode resulting in either the link-up taking a
long time, or failing to link-up altogether...
Workaround:
After power-on, enable Cable Diagnostic Mode for all ports and disable
it..."
Implement the proposed workaround unconditionally in the Intel XWAY driver
(MaxLinear GSW1xx switches incorporate Intel XWAY PHYs) because the
diagnostic bits have the same meaning even in older integral PHYs such as
GPY111/PEF7071/PHY11G. So it's not clear how to distinguish the affected
newer integrated PHYs, but the workaround should not hurt the older PHYs.
Cc: stable@vger.kernel.org
Fixes: 22335939ec ("net: dsa: add driver for MaxLinear GSW1xx switch family")
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20260922075251.23386-1-alexander.sverdlin@siemens.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
smcr_port_err() traverses smc_lgr_list.list without holding
smc_lgr_list.lock, allowing a concurrent smc_lgr_terminate_sched()
to free an lgr while it is still being dereferenced.
Hold smc_lgr_list.lock across the traversal. Update
smc_ib_gid_check() to call smcr_port_err() after releasing the lock.
Fixes: 541afa10c1 ("net/smc: add smcr_port_err() and smcr_link_down() processing")
Reviewed-by: Mahanta Jambigi <mjambigi@linux.ibm.com>
Signed-off-by: Sidraya Jayagond <sidraya@linux.ibm.com>
Reviewed-by: Dust Li <dust.li@linux.alibaba.com>
Link: https://patch.msgid.link/20260922073149.474762-1-sidraya@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
__rds_conn_create() computes npaths from the caller's transport before
it decides whether a connection to one of the host's own addresses is
to be handled by the loopback transport instead. That substitution is
what an RDS/TCP socket sending to a local address gets, and after it
the path init loop still runs for the TCP transport's RDS_MPATH_WORKERS
paths and allocates an ordered workqueue for each, while
rds_loop_conn_alloc() only ever provides transport data for path 0.
rds_conn_destroy() sizes its teardown from c_trans, by then the
loopback transport, so it visits path 0 only - and
rds_conn_path_destroy() would skip the other paths anyway, since it
returns before destroy_workqueue() for a path without transport data.
kfree(c_path) then drops the last pointers to seven workqueues. That
repeats for every such connection, on every netns teardown or module
unload, and every distinct local destination address is a separate
connection.
Recompute npaths once the transport is final, so that creation and
destruction agree on the set of paths. The c_path array stays sized
for the caller's transport; the unused entries are freed with it.
Fixes: 4716af3897 ("net/rds: Give each connection path its own workqueue")
Signed-off-by: Allison Henderson <achender@kernel.org>
Link: https://patch.msgid.link/20260921215027.174657-1-achender@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
nfp_net_ipsec_rx() drops the XArray lock before taking a reference to the
xfrm_state it found. The delete path can erase the entry and drop the last
state reference in that interval. RX can then try to increment a zero
refcount after the state has been queued for destruction.
The driver queues firmware invalidation asynchronously; the delete path
does not wait for the command to complete or drain pending RX processing.
The XFRM garbage collector waits for an RCU grace period before freeing
the state. That delays reclamation but does not make acquiring a reference
from zero valid.
Take the xfrm_state reference before releasing the XArray lock so
xa_erase() cannot run between lookup and reference acquisition.
Fixes: 57f273adbc ("nfp: add framework to support ipsec offloading")
Reported-by: Changyul Lee <lcy8047@gmail.com>
Signed-off-by: Sang-Hoon Choi <csh0052@gmail.com>
Link: https://patch.msgid.link/179001455912.44752.17153022439349797877.idr-bug-92@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Guangshuo Li says:
====================
net: ena: fix resource cleanup on probe failure
This series fixes two resource leaks in the ena_probe() error path after
ena_device_init() has successfully initialized device resources.
Patch 1 adds the missing PHC cleanup.
Patch 2 adds the missing MMIO read request cleanup.
====================
Link: https://patch.msgid.link/20260921154202.471662-1-lgs201920130244@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
ena_device_init() initializes the MMIO read mechanism with
ena_com_mmio_reg_read_request_init(), which allocates a coherent DMA
buffer for MMIO read responses.
The normal removal path releases this buffer through
ena_com_mmio_reg_read_request_destroy(). However, if ena_probe() fails
after ena_device_init() succeeds, the error path destroys the admin
resources and eventually frees ena_dev without destroying the MMIO read
request, leaving the coherent DMA buffer allocated.
Call ena_com_mmio_reg_read_request_destroy() in the probe error path
before releasing the remaining device resources.
This issue was found by manual code inspection.
Fixes: 1738cd3ed3 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Cc: stable@vger.kernel.org
Signed-off-by: Guangshuo Li <lgs201920130244@gmail.com>
Link: https://patch.msgid.link/20260921154202.471662-3-lgs201920130244@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
ena_probe() initializes the PHC as part of ena_device_init(), but the
probe failure path does not destroy it before freeing the PHC private
data.
The normal removal path calls ena_phc_destroy() through
ena_destroy_device() before ena_phc_free(). However, if probe fails
after ena_device_init() succeeds, the error path reaches ena_phc_free()
without unregistering the PTP clock or destroying the device PHC
resources.
Call ena_phc_destroy() in the probe error path before freeing the PHC
private data.
This issue was found by manual code inspection.
Cc: stable@vger.kernel.org tags and describe this as a consistency cleanup
Fixes: e0ea34158e ("net: ena: Add PHC support in the ENA driver")
Cc: stable@vger.kernel.org
Signed-off-by: Guangshuo Li <lgs201920130244@gmail.com>
Cc: stable
Link: https://patch.msgid.link/20260921154202.471662-2-lgs201920130244@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Ilya Maximets says:
====================
ovs, net/sched: fixes for UAF after conntrack extension realloc
One clean up change plus two fixes for the UAF on helper extension
realloc x 2. First half for OVS and the second half for the similar
code in act_ct. This should cover all the known cases of this problem
in these two modules.
====================
Link: https://patch.msgid.link/20260921145655.3167436-1-i.maximets@ovn.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
While calling the helpers, a raw pointer to the extensions area is
wired into expectations list:
-> nf_ct_helper()
-> helper->help()
-> nf_ct_expect_related_report()
-> nf_ct_expect_insert()
-> hlist_add_head_rcu(&exp->lnode, &master_help->expectations)
In case the connection is not confirmed yet, more extensions can be
added afterwards with *_ext_add() calls reallocating the extension
space and leaving the now invalid pointer in the expectations list
that is later accessed while removing the expectation.
Make sure that helpers are called at the end after all the other
extensions are already added.
Note that the helper rejection now leaves the mark and labels set,
but that's not different from how the NAT was handled before or how
the mark and the labels were handled on confirmation failure. And
there are no atomicity guarantees provided by the API anyway.
Fixes: a21b06e731 ("net: sched: add helper support in act_ct")
Cc: stable@vger.kernel.org
Reported-by: Axel Mierczuk <axel.mierczuk@1password.com>
Signed-off-by: Ilya Maximets <i.maximets@ovn.org>
Reviewed-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Jamal Hadi Salim <jhs@mojatatu.com>
Reviewed-by: Aaron Conole <aconole@redhat.com>
Link: https://patch.msgid.link/20260921145655.3167436-7-i.maximets@ovn.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This variable can only become 'true' when the connection is not
confirmed, but it is only checked when it is confirmed. So, it can be
treated as being always false and just removed.
Fixes: a21b06e731 ("net: sched: add helper support in act_ct")
Cc: stable@vger.kernel.org
Signed-off-by: Ilya Maximets <i.maximets@ovn.org>
Reviewed-by: Aaron Conole <aconole@redhat.com>
Reviewed-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Jamal Hadi Salim <jhs@mojatatu.com>
Link: https://patch.msgid.link/20260921145655.3167436-6-i.maximets@ovn.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
