commit f36cf386e3 upstream.
Intel provided the following information:
On all current Atom processors, instructions that use a segment register
value (e.g. a load or store) will not speculatively execute before the
last writer of that segment retires. Thus they will not use a
speculatively written segment value.
That means on ATOMs there is no speculation through SWAPGS, so the SWAPGS
entry paths can be excluded from the extra LFENCE if PTI is disabled.
Create a separate bug flag for the through SWAPGS speculation and mark all
out-of-order ATOMs and AMD/HYGON CPUs as not affected. The in-order ATOMs
are excluded from the whole mitigation mess anyway.
Reported-by: Andrew Cooper <andrew.cooper3@citrix.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Tyler Hicks <tyhicks@canonical.com>
Reviewed-by: Josh Poimboeuf <jpoimboe@redhat.com>
[bwh: Backported to 3.16:
- There's no whitelist entry (or any support) for Hygon CPUs
- Use the next available X86_BUG number
- Adjust context, indentation]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 64dbc122b2 upstream.
Somehow the swapgs mitigation entry code patch ended up with a JMPQ
instruction instead of JMP, where only the short jump is needed. Some
assembler versions apparently fail to optimize JMPQ into a two-byte JMP
when possible, instead always using a 7-byte JMP with relocation. For
some reason that makes the entry code explode with a #GP during boot.
Change it back to "JMP" as originally intended.
Fixes: 18ec54fdd6 ("x86/speculation: Prepare entry code for Spectre v1 swapgs mitigations")
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
[bwh: Backported to 3.16: adjust filename, context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit a205982598 upstream.
The previous commit added macro calls in the entry code which mitigate the
Spectre v1 swapgs issue if the X86_FEATURE_FENCE_SWAPGS_* features are
enabled. Enable those features where applicable.
The mitigations may be disabled with "nospectre_v1" or "mitigations=off".
There are different features which can affect the risk of attack:
- When FSGSBASE is enabled, unprivileged users are able to place any
value in GS, using the wrgsbase instruction. This means they can
write a GS value which points to any value in kernel space, which can
be useful with the following gadget in an interrupt/exception/NMI
handler:
if (coming from user space)
swapgs
mov %gs:<percpu_offset>, %reg1
// dependent load or store based on the value of %reg
// for example: mov %(reg1), %reg2
If an interrupt is coming from user space, and the entry code
speculatively skips the swapgs (due to user branch mistraining), it
may speculatively execute the GS-based load and a subsequent dependent
load or store, exposing the kernel data to an L1 side channel leak.
Note that, on Intel, a similar attack exists in the above gadget when
coming from kernel space, if the swapgs gets speculatively executed to
switch back to the user GS. On AMD, this variant isn't possible
because swapgs is serializing with respect to future GS-based
accesses.
NOTE: The FSGSBASE patch set hasn't been merged yet, so the above case
doesn't exist quite yet.
- When FSGSBASE is disabled, the issue is mitigated somewhat because
unprivileged users must use prctl(ARCH_SET_GS) to set GS, which
restricts GS values to user space addresses only. That means the
gadget would need an additional step, since the target kernel address
needs to be read from user space first. Something like:
if (coming from user space)
swapgs
mov %gs:<percpu_offset>, %reg1
mov (%reg1), %reg2
// dependent load or store based on the value of %reg2
// for example: mov %(reg2), %reg3
It's difficult to audit for this gadget in all the handlers, so while
there are no known instances of it, it's entirely possible that it
exists somewhere (or could be introduced in the future). Without
tooling to analyze all such code paths, consider it vulnerable.
Effects of SMAP on the !FSGSBASE case:
- If SMAP is enabled, and the CPU reports RDCL_NO (i.e., not
susceptible to Meltdown), the kernel is prevented from speculatively
reading user space memory, even L1 cached values. This effectively
disables the !FSGSBASE attack vector.
- If SMAP is enabled, but the CPU *is* susceptible to Meltdown, SMAP
still prevents the kernel from speculatively reading user space
memory. But it does *not* prevent the kernel from reading the
user value from L1, if it has already been cached. This is probably
only a small hurdle for an attacker to overcome.
Thanks to Dave Hansen for contributing the speculative_smap() function.
Thanks to Andrew Cooper for providing the inside scoop on whether swapgs
is serializing on AMD.
[ tglx: Fixed the USER fence decision and polished the comment as suggested
by Dave Hansen ]
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Dave Hansen <dave.hansen@intel.com>
[bwh: Backported to 3.16:
- Check for X86_FEATURE_KAISER instead of X86_FEATURE_PTI
- mitigations= parameter is x86-only here
- powerpc doesn't have Spectre mitigations
- Don't use __ro_after_init
- Adjust filename, context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 18ec54fdd6 upstream.
Spectre v1 isn't only about array bounds checks. It can affect any
conditional checks. The kernel entry code interrupt, exception, and NMI
handlers all have conditional swapgs checks. Those may be problematic in
the context of Spectre v1, as kernel code can speculatively run with a user
GS.
For example:
if (coming from user space)
swapgs
mov %gs:<percpu_offset>, %reg
mov (%reg), %reg1
When coming from user space, the CPU can speculatively skip the swapgs, and
then do a speculative percpu load using the user GS value. So the user can
speculatively force a read of any kernel value. If a gadget exists which
uses the percpu value as an address in another load/store, then the
contents of the kernel value may become visible via an L1 side channel
attack.
A similar attack exists when coming from kernel space. The CPU can
speculatively do the swapgs, causing the user GS to get used for the rest
of the speculative window.
The mitigation is similar to a traditional Spectre v1 mitigation, except:
a) index masking isn't possible; because the index (percpu offset)
isn't user-controlled; and
b) an lfence is needed in both the "from user" swapgs path and the
"from kernel" non-swapgs path (because of the two attacks described
above).
The user entry swapgs paths already have SWITCH_TO_KERNEL_CR3, which has a
CR3 write when PTI is enabled. Since CR3 writes are serializing, the
lfences can be skipped in those cases.
On the other hand, the kernel entry swapgs paths don't depend on PTI.
To avoid unnecessary lfences for the user entry case, create two separate
features for alternative patching:
X86_FEATURE_FENCE_SWAPGS_USER
X86_FEATURE_FENCE_SWAPGS_KERNEL
Use these features in entry code to patch in lfences where needed.
The features aren't enabled yet, so there's no functional change.
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Dave Hansen <dave.hansen@intel.com>
[bwh: Backported to 3.16:
- Assign the CPU feature bits from word 7
- Add FENCE_SWAPGS_KERNEL_ENTRY to NMI entry, since it does not
use paranoid_entry
- Add a return after .Lerror_entry_from_usermode_after_swapgs, done
upstream by commit f10750536f "x86/entry/64: Fix irqflag tracing wrt
context tracking"
- Include <asm/cpufeatures.h> in calling.h
- Adjust filenames, context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 2fa5f04f85 upstream.
This warning:
WARNING: CPU: 0 PID: 3331 at arch/x86/entry/common.c:45 enter_from_user_mode+0x32/0x50
CPU: 0 PID: 3331 Comm: ldt_gdt_64 Not tainted 4.8.0-rc7+ #13
Call Trace:
dump_stack+0x99/0xd0
__warn+0xd1/0xf0
warn_slowpath_null+0x1d/0x20
enter_from_user_mode+0x32/0x50
error_entry+0x6d/0xc0
? general_protection+0x12/0x30
? native_load_gs_index+0xd/0x20
? do_set_thread_area+0x19c/0x1f0
SyS_set_thread_area+0x24/0x30
do_int80_syscall_32+0x7c/0x220
entry_INT80_compat+0x38/0x50
... can be reproduced by running the GS testcase of the ldt_gdt test unit in
the x86 selftests.
do_int80_syscall_32() will call enter_form_user_mode() to convert context
tracking state from user state to kernel state. The load_gs_index() call
can fail with user gsbase, gsbase will be fixed up and proceed if this
happen.
However, enter_from_user_mode() will be called again in the fixed up path
though it is context tracking kernel state currently.
This patch fixes it by just fixing up gsbase and telling lockdep that IRQs
are off once load_gs_index() failed with user gsbase.
Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com>
Acked-by: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1475197266-3440-1-git-send-email-wanpeng.li@hotmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
[bwh: Backported to 3.16 as dependency of commit 18ec54fdd6
"x86/speculation: Prepare entry code for Spectre v1 swapgs mitigations":
- Adjust filename]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit cb6f64ed5a upstream.
In 539f511365 ("x86/asm/entry/64: Disentangle error_entry/exit
gsbase/ebx/usermode code"), I arranged the code slightly wrong
-- IRET faults would skip the code path that was intended to
execute on all error entries from user mode. Fix it up.
While we're at it, make all the labels in error_entry local.
This does not fix a bug, but we'll need it, and it slightly
shrinks the code.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Denys Vlasenko <vda.linux@googlemail.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: paulmck@linux.vnet.ibm.com
Link: http://lkml.kernel.org/r/91e17891e49fa3d61357eadc451529ad48143ee1.1435952415.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
[bwh: Backported to 3.16 as dependency of commit 18ec54fdd6
"x86/speculation: Prepare entry code for Spectre v1 swapgs mitigations":
- Adjust filename, context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 539f511365 upstream.
The error_entry/error_exit code to handle gsbase and whether we
return to user mdoe was a mess:
- error_sti was misnamed. In particular, it did not enable interrupts.
- Error handling for gs_change was hopelessly tangled the normal
usermode path. Separate it out. This saves a branch in normal
entries from kernel mode.
- The comments were bad.
Fix it up. As a nice side effect, there's now a code path that
happens on error entries from user mode. We'll use it soon.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/f1be898ab93360169fb845ab85185948832209ee.1433878454.git.luto@kernel.org
[ Prettified it, clarified comments some more. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
[bwh: Backported to 3.16 as dependency of commit 18ec54fdd6
"x86/speculation: Prepare entry code for Spectre v1 swapgs mitigations":
- We do not use %ebx as a flag since we already have a backport of commit
b3681dd548 "x86/entry/64: Remove %ebx handling from error_entry/exit",
so don't add the comments about that
- Adjust filename, context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Use the same bit numbers for all features that are also present in
4.4.y and 4.9.y, to make further backports slightly easier.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 4e9036042f upstream.
To choose whether to pick the GID from the old (16bit) or new (32bit)
field, we should check if the old gid field is set to 0xffff. Mainline
checks the old *UID* field instead - cut'n'paste from the corresponding
code in ufs_get_inode_uid().
Fixes: 252e211e90
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 486efdc8f6 upstream.
Packet sockets in datagram mode take a destination address. Verify its
length before passing to dev_hard_header.
Prior to 2.6.14-rc3, the send code ignored sll_halen. This is
established behavior. Directly compare msg_namelen to dev->addr_len.
Change v1->v2: initialize addr in all paths
Fixes: 6b8d95f179 ("packet: validate address length if non-zero")
Suggested-by: David Laight <David.Laight@aculab.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit b2cf86e156 upstream.
Packet send checks that msg_name is at least sizeof sockaddr_ll.
Packet recv must return at least this length, so that its output
can be passed unmodified to packet send.
This ceased to be true since adding support for lladdr longer than
sll_addr. Since, the return value uses true address length.
Always return at least sizeof sockaddr_ll, even if address length
is shorter. Zero the padding bytes.
Change v1->v2: do not overwrite zeroed padding again. use copy_len.
Fixes: 0fb375fb9b ("[AF_PACKET]: Allow for > 8 byte hardware addresses.")
Suggested-by: David Laight <David.Laight@aculab.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 95c169251b upstream.
A request for a flowlabel fails in process or user exclusive mode must
fail if the caller pid or uid does not match. Invert the test.
Previously, the test was unsafe wrt PID recycling, but indeed tested
for inequality: fl1->owner != fl->owner
Fixes: 4f82f45730 ("net ip6 flowlabel: Make owner a union of struct pid* and kuid_t")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit baf76f0c58 upstream.
This way, slhc_free() accepts what slhc_init() returns, whether that is
an error or not.
In particular, the pattern in sl_alloc_bufs() is
slcomp = slhc_init(16, 16);
...
slhc_free(slcomp);
for the error handling path, and rather than complicate that code, just
make it ok to always free what was returned by the init function.
That's what the code used to do before commit 4ab42d78e3 ("ppp, slip:
Validate VJ compression slot parameters completely") when slhc_init()
just returned NULL for the error case, with no actual indication of the
details of the error.
Reported-by: syzbot+45474c076a4927533d2e@syzkaller.appspotmail.com
Fixes: 4ab42d78e3 ("ppp, slip: Validate VJ compression slot parameters completely")
Acked-by: Ben Hutchings <ben@decadent.org.uk>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit d6097c9e44 upstream.
Unless the very next line is schedule(), or implies it, one must not use
preempt_enable_no_resched(). It can cause a preemption to go missing and
thereby cause arbitrary delays, breaking the PREEMPT=y invariant.
Link: http://lkml.kernel.org/r/20190423200318.GY14281@hirez.programming.kicks-ass.net
Cc: Waiman Long <longman@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: the arch/x86 maintainers <x86@kernel.org>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Tim Chen <tim.c.chen@linux.intel.com>
Cc: huang ying <huang.ying.caritas@gmail.com>
Cc: Roman Gushchin <guro@fb.com>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Fixes: 2c2d7329d8 ("tracing/ftrace: use preempt_enable_no_resched_notrace in ring_buffer_time_stamp()")
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit c1c4772178 upstream.
Canonical way to fetch sk_user_data from an encap_rcv() handler called
from UDP stack in rcu protected section is to use rcu_dereference_sk_user_data(),
otherwise compiler might read it multiple times.
Fixes: d00fa9adc5 ("il2tp: fix races with tunnel socket close")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: James Chapman <jchapman@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit a860fa7b96 upstream.
sched_clock_cpu() may not be consistent between CPUs. If a task
migrates to another CPU, then se.exec_start is set to that CPU's
rq_clock_task() by update_stats_curr_start(). Specifically, the new
value might be before the old value due to clock skew.
So then if in numa_get_avg_runtime() the expression:
'now - p->last_task_numa_placement'
ends up as -1, then the divider '*period + 1' in task_numa_placement()
is 0 and things go bang. Similar to update_curr(), check if time goes
backwards to avoid this.
[ peterz: Wrote new changelog. ]
[ mingo: Tweaked the code comment. ]
Signed-off-by: Xie XiuQi <xiexiuqi@huawei.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: cj.chengjian@huawei.com
Link: http://lkml.kernel.org/r/20190425080016.GX11158@hirez.programming.kicks-ass.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit c409ca3be3 upstream.
Change the validation of number_of_packets in get_pipe to compare the
number of packets to a fixed maximum number of packets allowed, set to
be 1024. This number was chosen due to it being used by other drivers as
well, for example drivers/usb/host/uhci-q.c
Background/reason:
The get_pipe function in stub_rx.c validates the number of packets in
isochronous mode and aborts with an error if that number is too large,
in order to prevent malicious input from possibly triggering large
memory allocations. This was previously done by checking whether
pdu->u.cmd_submit.number_of_packets is bigger than the number of packets
that would be needed for pdu->u.cmd_submit.transfer_buffer_length bytes
if all except possibly the last packet had maximum length, given by
usb_endpoint_maxp(epd) * usb_endpoint_maxp_mult(epd). This leads to an
error if URBs with packets shorter than the maximum possible length are
submitted, which is allowed according to
Documentation/driver-api/usb/URB.rst and occurs for example with the
snd-usb-audio driver.
Fixes: c6688ef9f2 ("usbip: fix stub_rx: harden CMD_SUBMIT path to handle malicious input")
Signed-off-by: Malte Leip <malte@leip.net>
Acked-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[bwh: Backported to 3.16: adjust filenames]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit c114944d7d upstream.
The syzkaller USB fuzzer spotted a slab-out-of-bounds bug in the
ds2490 driver. This bug is caused by improper use of the altsetting
array in the usb_interface structure (the array's entries are not
always stored in numerical order), combined with a naive assumption
that all interfaces probed by the driver will have the expected number
of altsettings.
The bug can be fixed by replacing references to the possibly
non-existent intf->altsetting[alt] entry with the guaranteed-to-exist
intf->cur_altsetting entry.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: syzbot+d65f673b847a1a96cdba@syzkaller.appspotmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit ef61eb43ad upstream.
The syzkaller USB fuzzer found a general-protection-fault bug in the
yurex driver. The fault occurs when a device has been unplugged; the
driver's interrupt-URB handler logs an error message referring to the
device by name, after the device has been unregistered and its name
deallocated.
This problem is caused by the fact that the interrupt URB isn't
cancelled until the driver's private data structure is released, which
can happen long after the device is gone. The cure is to make sure
that the interrupt URB is killed before yurex_disconnect() returns;
this is exactly the sort of thing that usb_poison_urb() was meant for.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: syzbot+2eb9121678bdb36e6d57@syzkaller.appspotmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 652727bbe1 upstream.
A path-based rename returning EBUSY will incorrectly try opening
the file with a cifs (NT Create AndX) operation on an smb2+ mount,
which causes the server to force a session close.
If the mount is smb2+, skip the fallback.
Signed-off-by: Frank Sorenson <sorenson@redhat.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 76a495d666 upstream.
Take the d_lock here to ensure that d_name doesn't change.
Signed-off-by: Jeff Layton <jlayton@kernel.org>
Reviewed-by: "Yan, Zheng" <zyan@redhat.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 5178791474 upstream.
We need to dereference the directory to get its parent to
be able to rename it, so it's clearly not safe to try to
do this with ERR_PTR() pointers. Skip in this case.
It seems that this is most likely what was causing the
report by syzbot, but I'm not entirely sure as it didn't
come with a reproducer this time.
Reported-by: syzbot+4ece1a28b8f4730547c9@syzkaller.appspotmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 7caa56f006 upstream.
It means userspace gave us a ruleset where there is some other
data after the ebtables target but before the beginning of the next rule.
Fixes: 81e675c227 ("netfilter: ebtables: add CONFIG_COMPAT support")
Reported-by: syzbot+659574e7bcc7f7eb4df7@syzkaller.appspotmail.com
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 925b0c841e upstream.
If we add a bond device which is already the master of the team interface,
we will hold the team->lock in team_add_slave() first and then request the
lock in team_set_mac_address() again. The functions are called like:
- team_add_slave()
- team_port_add()
- team_port_enter()
- team_modeop_port_enter()
- __set_port_dev_addr()
- dev_set_mac_address()
- bond_set_mac_address()
- dev_set_mac_address()
- team_set_mac_address
Although team_upper_dev_link() would check the upper devices but it is
called too late. Fix it by adding a checking before processing the slave.
v2: Do not split the string in netdev_err()
Fixes: 3d249d4ca7 ("net: introduce ethernet teaming device")
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backported to 3.16: netlink doesn't support extack]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit c2b71462d2 upstream.
The syzkaller fuzzer reported a bug in the USB hub driver which turned
out to be caused by a negative runtime-PM usage counter. This allowed
a hub to be runtime suspended at a time when the driver did not expect
it. The symptom is a WARNING issued because the hub's status URB is
submitted while it is already active:
URB 0000000031fb463e submitted while active
WARNING: CPU: 0 PID: 2917 at drivers/usb/core/urb.c:363
The negative runtime-PM usage count was caused by an unfortunate
design decision made when runtime PM was first implemented for USB.
At that time, USB class drivers were allowed to unbind from their
interfaces without balancing the usage counter (i.e., leaving it with
a positive count). The core code would take care of setting the
counter back to 0 before allowing another driver to bind to the
interface.
Later on when runtime PM was implemented for the entire kernel, the
opposite decision was made: Drivers were required to balance their
runtime-PM get and put calls. In order to maintain backward
compatibility, however, the USB subsystem adapted to the new
implementation by keeping an independent usage counter for each
interface and using it to automatically adjust the normal usage
counter back to 0 whenever a driver was unbound.
This approach involves duplicating information, but what is worse, it
doesn't work properly in cases where a USB class driver delays
decrementing the usage counter until after the driver's disconnect()
routine has returned and the counter has been adjusted back to 0.
Doing so would cause the usage counter to become negative. There's
even a warning about this in the USB power management documentation!
As it happens, this is exactly what the hub driver does. The
kick_hub_wq() routine increments the runtime-PM usage counter, and the
corresponding decrement is carried out by hub_event() in the context
of the hub_wq work-queue thread. This work routine may sometimes run
after the driver has been unbound from its interface, and when it does
it causes the usage counter to go negative.
It is not possible for hub_disconnect() to wait for a pending
hub_event() call to finish, because hub_disconnect() is called with
the device lock held and hub_event() acquires that lock. The only
feasible fix is to reverse the original design decision: remove the
duplicate interface-specific usage counter and require USB drivers to
balance their runtime PM gets and puts. As far as I know, all
existing drivers currently do this.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: syzbot+7634edaea4d0b341c625@syzkaller.appspotmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[bwh: Backported to 3.16:
- Adjust documentation filename
- Don't add ReST markup in documentation
- Update use of pm_usage_cnt in poseidon driver, which has been
removed upstream]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit e8277b3b52 upstream.
Commit 58bc4c34d2 ("mm/vmstat.c: skip NR_TLB_REMOTE_FLUSH* properly")
depends on skipping vmstat entries with empty name introduced in
7aaf772723 ("mm: don't show nr_indirectly_reclaimable in
/proc/vmstat") but reverted in b29940c1ab ("mm: rename and change
semantics of nr_indirectly_reclaimable_bytes").
So skipping no longer works and /proc/vmstat has misformatted lines " 0".
This patch simply shows debug counters "nr_tlb_remote_*" for UP.
Link: http://lkml.kernel.org/r/155481488468.467.4295519102880913454.stgit@buzz
Fixes: 58bc4c34d2 ("mm/vmstat.c: skip NR_TLB_REMOTE_FLUSH* properly")
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Roman Gushchin <guro@fb.com>
Cc: Jann Horn <jannh@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit b191fa96ea upstream.
Avoid kretprobe recursion loop bg by setting a dummy
kprobes to current_kprobe per-CPU variable.
This bug has been introduced with the asm-coded trampoline
code, since previously it used another kprobe for hooking
the function return placeholder (which only has a nop) and
trampoline handler was called from that kprobe.
This revives the old lost kprobe again.
With this fix, we don't see deadlock anymore.
And you can see that all inner-called kretprobe are skipped.
event_1 235 0
event_2 19375 19612
The 1st column is recorded count and the 2nd is missed count.
Above shows (event_1 rec) + (event_2 rec) ~= (event_2 missed)
(some difference are here because the counter is racy)
Reported-by: Andrea Righi <righi.andrea@gmail.com>
Tested-by: Andrea Righi <righi.andrea@gmail.com>
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: c9becf58d9 ("[PATCH] kretprobe: kretprobe-booster")
Link: http://lkml.kernel.org/r/155094064889.6137.972160690963039.stgit@devbox
Signed-off-by: Ingo Molnar <mingo@kernel.org>
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit fabe38ab6b upstream.
Mark ftrace mcount handler functions nokprobe since
probing on these functions with kretprobe pushes
return address incorrectly on kretprobe shadow stack.
Reported-by: Francis Deslauriers <francis.deslauriers@efficios.com>
Tested-by: Andrea Righi <righi.andrea@gmail.com>
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Acked-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/155094062044.6137.6419622920568680640.stgit@devbox
Signed-off-by: Ingo Molnar <mingo@kernel.org>
[bwh: Backported to 3.16: there is no ftrace_ops_assist_func()]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 3ff9c075cc upstream.
Verify the stack frame pointer on kretprobe trampoline handler,
If the stack frame pointer does not match, it skips the wrong
entry and tries to find correct one.
This can happen if user puts the kretprobe on the function
which can be used in the path of ftrace user-function call.
Such functions should not be probed, so this adds a warning
message that reports which function should be blacklisted.
Tested-by: Andrea Righi <righi.andrea@gmail.com>
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/155094059185.6137.15527904013362842072.stgit@devbox
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 4bcd4ec101 upstream.
We find that sysctl_tipc_rmem and named_timeout do not have the right minimum
setting. sysctl_tipc_rmem should be larger than zero, like sysctl_tcp_rmem.
And named_timeout as a timeout setting should be not less than zero.
Fixes: cc79dd1ba9 ("tipc: change socket buffer overflow control to respect sk_rcvbuf")
Fixes: a5325ae5b8 ("tipc: add name distributor resiliency queue")
Signed-off-by: Jie Liu <liujie165@huawei.com>
Reported-by: Qiang Ning <ningqiang1@huawei.com>
Reviewed-by: Zhiqiang Liu <liuzhiqiang26@huawei.com>
Reviewed-by: Miaohe Lin <linmiaohe@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backported to 3.16: only the tipc_rmem sysctl exists here]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 2a3f7221ac upstream.
There is a small race window in the card disconnection code that
allows the registration of another card with the very same card id.
This leads to a warning in procfs creation as caught by syzkaller.
The problem is that we delete snd_cards and snd_cards_lock entries at
the very beginning of the disconnection procedure. This makes the
slot available to be assigned for another card object while the
disconnection procedure is being processed. Then it becomes possible
to issue a procfs registration with the existing file name although we
check the conflict beforehand.
The fix is simply to move the snd_cards and snd_cards_lock clearances
at the end of the disconnection procedure. The references to these
entries are merely either from the global proc files like
/proc/asound/cards or from the card registration / disconnection, so
it should be fine to shift at the very end.
Reported-by: syzbot+48df349490c36f9f54ab@syzkaller.appspotmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 2e8e192263 upstream.
With extremely short cfs_period_us setting on a parent task group with a large
number of children the for loop in sched_cfs_period_timer() can run until the
watchdog fires. There is no guarantee that the call to hrtimer_forward_now()
will ever return 0. The large number of children can make
do_sched_cfs_period_timer() take longer than the period.
NMI watchdog: Watchdog detected hard LOCKUP on cpu 24
RIP: 0010:tg_nop+0x0/0x10
<IRQ>
walk_tg_tree_from+0x29/0xb0
unthrottle_cfs_rq+0xe0/0x1a0
distribute_cfs_runtime+0xd3/0xf0
sched_cfs_period_timer+0xcb/0x160
? sched_cfs_slack_timer+0xd0/0xd0
__hrtimer_run_queues+0xfb/0x270
hrtimer_interrupt+0x122/0x270
smp_apic_timer_interrupt+0x6a/0x140
apic_timer_interrupt+0xf/0x20
</IRQ>
To prevent this we add protection to the loop that detects when the loop has run
too many times and scales the period and quota up, proportionally, so that the timer
can complete before then next period expires. This preserves the relative runtime
quota while preventing the hard lockup.
A warning is issued reporting this state and the new values.
Signed-off-by: Phil Auld <pauld@redhat.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Anton Blanchard <anton@ozlabs.org>
Cc: Ben Segall <bsegall@google.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20190319130005.25492-1-pauld@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit b98749cac4 upstream.
In the oplock break handler, writing pending changes from pages puts
the FileInfo handle. If the refcount reaches zero it closes the handle
and waits for any oplock break handler to return, thus causing a deadlock.
To prevent this situation:
* We add a wait flag to cifsFileInfo_put() to decide whether we should
wait for running/pending oplock break handlers
* We keep an additionnal reference of the SMB FileInfo handle so that
for the rest of the handler putting the handle won't close it.
- The ref is bumped everytime we queue the handler via the
cifs_queue_oplock_break() helper.
- The ref is decremented at the end of the handler
This bug was triggered by xfstest 464.
Also important fix to address the various reports of
oops in smb2_push_mandatory_locks
Signed-off-by: Aurelien Aptel <aaptel@suse.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit e6d0fb7b34 upstream.
If we enter smb2_query_symlink() for something that is not a symlink
and where the SMB2_open() would succeed we would never end up
closing this handle and would thus leak a handle on the server.
Fix this by immediately calling SMB2_close() on successfull open.
Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com>
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit f32c2877bc upstream.
There was a missing comparison with 0 when checking if type is "s64" or
"u64". Therefore, the body of the if-statement was entered if "type" was
"u64" or not "s64", which made the first strcmp() redundant since if
type is "u64", it's not "s64".
If type is "s64", the body of the if-statement is not entered but since
the remainder of the function consists of if-statements which will not
be entered if type is "s64", we will just return "val", which is
correct, albeit at the cost of a few more calls to strcmp(), i.e., it
will behave just as if the if-statement was entered.
If type is neither "s64" or "u64", the body of the if-statement will be
entered incorrectly and "val" returned. This means that any type that is
checked after "s64" and "u64" is handled the same way as "s64" and
"u64", i.e., the limiting of "val" to fit in for example "s8" is never
reached.
This was introduced in the kernel tree when the sources were copied from
trace-cmd in commit f7d82350e5 ("tools/events: Add files to create
libtraceevent.a"), and in the trace-cmd repo in 1cdbae6035cei
("Implement typecasting in parser") when the function was introduced,
i.e., it has always behaved the wrong way.
Detected by cppcheck.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Reviewed-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Cc: Tzvetomir Stoyanov <tstoyanov@vmware.com>
Fixes: f7d82350e5 ("tools/events: Add files to create libtraceevent.a")
Link: http://lkml.kernel.org/r/20190409091529.2686-1-rikard.falkeborn@gmail.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit bc8a3d8925 upstream.
KVM bases its memory usage limits on the total number of guest pages
across all memslots. However, those limits, and the calculations to
produce them, use 32 bit unsigned integers. This can result in overflow
if a VM has more guest pages that can be represented by a u32. As a
result of this overflow, KVM can use a low limit on the number of MMU
pages it will allocate. This makes KVM unable to map all of guest memory
at once, prompting spurious faults.
Tested: Ran all kvm-unit-tests on an Intel Haswell machine. This patch
introduced no new failures.
Signed-off-by: Ben Gardon <bgardon@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 663d294b47 upstream.
`vmk80xx_alloc_usb_buffers()` is called from `vmk80xx_auto_attach()` to
allocate RX and TX buffers for USB transfers. It allocates
`devpriv->usb_rx_buf` followed by `devpriv->usb_tx_buf`. If the
allocation of `devpriv->usb_tx_buf` fails, it frees
`devpriv->usb_rx_buf`, leaving the pointer set dangling, and returns an
error. Later, `vmk80xx_detach()` will be called from the core comedi
module code to clean up. `vmk80xx_detach()` also frees both
`devpriv->usb_rx_buf` and `devpriv->usb_tx_buf`, but
`devpriv->usb_rx_buf` may have already been freed, leading to a
double-free error. Fix it by removing the call to
`kfree(devpriv->usb_rx_buf)` from `vmk80xx_alloc_usb_buffers()`, relying
on `vmk80xx_detach()` to free the memory.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 08b7c2f920 upstream.
If `vmk80xx_auto_attach()` returns an error, the core comedi module code
will call `vmk80xx_detach()` to clean up. If `vmk80xx_auto_attach()`
successfully allocated the comedi device private data,
`vmk80xx_detach()` assumes that a `struct semaphore limit_sem` contained
in the private data has been initialized and uses it. Unfortunately,
there are a couple of places where `vmk80xx_auto_attach()` can return an
error after allocating the device private data but before initializing
the semaphore, so this assumption is invalid. Fix it by initializing
the semaphore just after allocating the private data in
`vmk80xx_auto_attach()` before any other errors can be returned.
I believe this was the cause of the following syzbot crash report
<https://syzkaller.appspot.com/bug?extid=54c2f58f15fe6876b6ad>:
usb 1-1: config 0 has no interface number 0
usb 1-1: New USB device found, idVendor=10cf, idProduct=8068, bcdDevice=e6.8d
usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
usb 1-1: config 0 descriptor??
vmk80xx 1-1:0.117: driver 'vmk80xx' failed to auto-configure device.
INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
CPU: 0 PID: 12 Comm: kworker/0:1 Not tainted 5.1.0-rc4-319354-g9a33b36 #3
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Workqueue: usb_hub_wq hub_event
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0xe8/0x16e lib/dump_stack.c:113
assign_lock_key kernel/locking/lockdep.c:786 [inline]
register_lock_class+0x11b8/0x1250 kernel/locking/lockdep.c:1095
__lock_acquire+0xfb/0x37c0 kernel/locking/lockdep.c:3582
lock_acquire+0x10d/0x2f0 kernel/locking/lockdep.c:4211
__raw_spin_lock_irqsave include/linux/spinlock_api_smp.h:110 [inline]
_raw_spin_lock_irqsave+0x44/0x60 kernel/locking/spinlock.c:152
down+0x12/0x80 kernel/locking/semaphore.c:58
vmk80xx_detach+0x59/0x100 drivers/staging/comedi/drivers/vmk80xx.c:829
comedi_device_detach+0xed/0x800 drivers/staging/comedi/drivers.c:204
comedi_device_cleanup.part.0+0x68/0x140 drivers/staging/comedi/comedi_fops.c:156
comedi_device_cleanup drivers/staging/comedi/comedi_fops.c:187 [inline]
comedi_free_board_dev.part.0+0x16/0x90 drivers/staging/comedi/comedi_fops.c:190
comedi_free_board_dev drivers/staging/comedi/comedi_fops.c:189 [inline]
comedi_release_hardware_device+0x111/0x140 drivers/staging/comedi/comedi_fops.c:2880
comedi_auto_config.cold+0x124/0x1b0 drivers/staging/comedi/drivers.c:1068
usb_probe_interface+0x31d/0x820 drivers/usb/core/driver.c:361
really_probe+0x2da/0xb10 drivers/base/dd.c:509
driver_probe_device+0x21d/0x350 drivers/base/dd.c:671
__device_attach_driver+0x1d8/0x290 drivers/base/dd.c:778
bus_for_each_drv+0x163/0x1e0 drivers/base/bus.c:454
__device_attach+0x223/0x3a0 drivers/base/dd.c:844
bus_probe_device+0x1f1/0x2a0 drivers/base/bus.c:514
device_add+0xad2/0x16e0 drivers/base/core.c:2106
usb_set_configuration+0xdf7/0x1740 drivers/usb/core/message.c:2021
generic_probe+0xa2/0xda drivers/usb/core/generic.c:210
usb_probe_device+0xc0/0x150 drivers/usb/core/driver.c:266
really_probe+0x2da/0xb10 drivers/base/dd.c:509
driver_probe_device+0x21d/0x350 drivers/base/dd.c:671
__device_attach_driver+0x1d8/0x290 drivers/base/dd.c:778
bus_for_each_drv+0x163/0x1e0 drivers/base/bus.c:454
__device_attach+0x223/0x3a0 drivers/base/dd.c:844
bus_probe_device+0x1f1/0x2a0 drivers/base/bus.c:514
device_add+0xad2/0x16e0 drivers/base/core.c:2106
usb_new_device.cold+0x537/0xccf drivers/usb/core/hub.c:2534
hub_port_connect drivers/usb/core/hub.c:5089 [inline]
hub_port_connect_change drivers/usb/core/hub.c:5204 [inline]
port_event drivers/usb/core/hub.c:5350 [inline]
hub_event+0x138e/0x3b00 drivers/usb/core/hub.c:5432
process_one_work+0x90f/0x1580 kernel/workqueue.c:2269
worker_thread+0x9b/0xe20 kernel/workqueue.c:2415
kthread+0x313/0x420 kernel/kthread.c:253
ret_from_fork+0x3a/0x50 arch/x86/entry/entry_64.S:352
Reported-by: syzbot+54c2f58f15fe6876b6ad@syzkaller.appspotmail.com
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit c01c348ecd upstream.
Some drivers (such as the vub300 MMC driver) expect usb_string() to
return a properly NUL-terminated string, even when an error occurs.
(In fact, vub300's probe routine doesn't bother to check the return
code from usb_string().) When the driver goes on to use an
unterminated string, it leads to kernel errors such as
stack-out-of-bounds, as found by the syzkaller USB fuzzer.
An out-of-range string index argument is not at all unlikely, given
that some devices don't provide string descriptors and therefore list
0 as the value for their string indexes. This patch makes
usb_string() return a properly terminated empty string along with the
-EINVAL error code when an out-of-range index is encountered.
And since a USB string index is a single-byte value, indexes >= 256
are just as invalid as values of 0 or below.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: syzbot+b75b85111c10b8d680f1@syzkaller.appspotmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 79b4a9cf0e upstream.
Commit 4c21b8fd8f (MIPS: seccomp: Handle indirect system calls (o32))
added indirect syscall detection for O32 processes running on MIPS64,
but it did not work correctly for big endian kernel/processes. The
reason is that the syscall number is loaded from ARG1 using the lw
instruction while this is a 64-bit value, so zero is loaded instead of
the syscall number.
Fix the code by using the ld instruction instead. When running a 32-bit
processes on a 64 bit CPU, the values are properly sign-extended, so it
ensures the value passed to syscall_trace_enter is correct.
Recent systemd versions with seccomp enabled whitelist the getpid
syscall for their internal processes (e.g. systemd-journald), but call
it through syscall(SYS_getpid). This fix therefore allows O32 big endian
systems with a 64-bit kernel to run recent systemd versions.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 2f5fb19341 upstream.
Mikhail reported a lockdep splat related to the AMD specific ssb_state
lock:
CPU0 CPU1
lock(&st->lock);
local_irq_disable();
lock(&(&sighand->siglock)->rlock);
lock(&st->lock);
<Interrupt>
lock(&(&sighand->siglock)->rlock);
*** DEADLOCK ***
The connection between sighand->siglock and st->lock comes through seccomp,
which takes st->lock while holding sighand->siglock.
Make sure interrupts are disabled when __speculation_ctrl_update() is
invoked via prctl() -> speculation_ctrl_update(). Add a lockdep assert to
catch future offenders.
Fixes: 1f50ddb4f4 ("x86/speculation: Handle HT correctly on AMD")
Reported-by: Mikhail Gavrilov <mikhail.v.gavrilov@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Mikhail Gavrilov <mikhail.v.gavrilov@gmail.com>
Cc: Thomas Lendacky <thomas.lendacky@amd.com>
Link: https://lkml.kernel.org/r/alpine.DEB.2.21.1904141948200.4917@nanos.tec.linutronix.de
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit f54bb2ec02 upstream.
Checking whether IRQs are enabled or disabled is a very common sanity
check, however not free of overhead especially on fastpath where such
assertion is very common.
Lockdep is a good host for such concurrency correctness check and it
even already tracks down IRQs disablement state. Just reuse its
machinery. This will allow us to get rid of the flags pop and check
overhead from fast path when kernel is built for production.
Suggested-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: David S . Miller <davem@davemloft.net>
Cc: Lai Jiangshan <jiangshanlai@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Tejun Heo <tj@kernel.org>
Link: http://lkml.kernel.org/r/1509980490-4285-2-git-send-email-frederic@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 0a2c34f18c upstream.
Currently if a pci dma mapping failure is detected a free'd
memblock address is returned rather than a NULL (that indicates
an error). Fix this by ensuring NULL is returned on this error case.
Addresses-Coverity: ("Use after free")
Fixes: 528f727279 ("vxge: code cleanup and reorganization")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 746ba11f17 upstream.
Currently rt2x00 devices retransmit the management frames with
incremented sequence number if hardware is assigning the sequence.
This is HW bug fixed already for non-QOS data frames, but it should
be fixed for management frames except beacon.
Without fix retransmitted frames have wrong SN:
AlphaNet_e8:fb:36 Vivotek_52:31:51 Authentication, SN=1648, FN=0, Flags=........C Frame is not being retransmitted 1648 1
AlphaNet_e8:fb:36 Vivotek_52:31:51 Authentication, SN=1649, FN=0, Flags=....R...C Frame is being retransmitted 1649 1
AlphaNet_e8:fb:36 Vivotek_52:31:51 Authentication, SN=1650, FN=0, Flags=....R...C Frame is being retransmitted 1650 1
With the fix SN stays correctly the same:
88:6a:e3:e8:f9:a2 8c:f5:a3:88:76:87 Authentication, SN=1450, FN=0, Flags=........C
88:6a:e3:e8:f9:a2 8c:f5:a3:88:76:87 Authentication, SN=1450, FN=0, Flags=....R...C
88:6a:e3:e8:f9:a2 8c:f5:a3:88:76:87 Authentication, SN=1450, FN=0, Flags=....R...C
Signed-off-by: Vijayakumar Durai <vijayakumar.durai1@vivint.com>
[sgruszka: simplify code, change comments and changelog]
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
[bwh: Backported to 3.16: adjust filenames, context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 3c677d2062 upstream.
The exlcusion range limit register needs to contain the
base-address of the last page that is part of the range, as
bits 0-11 of this register are treated as 0xfff by the
hardware for comparisons.
So correctly set the exclusion range in the hardware to the
last page which is _in_ the range.
Fixes: b2026aa2dc ('x86, AMD IOMMU: add functions for programming IOMMU MMIO space')
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
