The stock bootloader on the Samsung Galaxy Tab 3 8.0 provides an
incorrect available memory range over ATAG_MEM. Limit the usable
memory in the DTS to prevent it from doing so, without having to
disable ATAG support.
Signed-off-by: Artur Weber <aweber.kernel@gmail.com>
Reviewed-by: Henrik Grimler <henrik@grimler.se>
Link: https://lore.kernel.org/r/20240217-tab3-limit-usable-memory-range-v1-1-49cc9c86a5cc@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Define CPU cluster 0 and CPU cluster 1 CMUs, which generate CPU clocks,
and add corresponding CPU clocks to CPU nodes.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Link: https://lore.kernel.org/r/20240301015118.30072-3-semen.protsenko@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Implement support for CPU clock management units:
- CMU_CPUCL0: clocks for cluster 0: 4 x Cortex-A55 (cpu0..cpu3)
- CMU_CPUCL1: clocks for cluster 1: 4 x Cortex-A55 (cpu4..cpu7)
CPU PLLs are generating main CPU clocks for each cluster, and there are
alternate ("switch") clocks that can be used temporarily while
re-configuring the PLL for a new rate. ACLK, ATCLK, PCLKDBG and
PERIPHCLK clocks are driving corresponding buses. CLK_CLUSTERx_SCLK are
actual leaf CPU clocks and should be used to change CPU rates. Also some
CoreSight clocks can be derived from DBG_USER (debug clock).
PLL table was extracted from ECT table. ECT stands for "Exynos
Characteristic Table", it's a Samsung specific binary data populated by
BL2 bootloader in RAM at 0x90000000 address, containing PLL tables for
various CMUs and other hardware specific information.
The particular PLL type used in CMU_CPUCL0 and CMU_CPUCL1 (pll0822x) is
an integer PLL with middle FVCO. The equation to calculate its output
rate is:
fout = fin * M / (P*2^S)
where:
fin = 26 MHz (OSCCLK frequency)
M = 64..1023
P = 1..63
S = 0..6
The PLL table tries to keep "P" value low to reduce the locking time,
which for pll0822x is "t = P * 150" (in OSCCLK cycles).
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Link: https://lore.kernel.org/r/20240301015118.30072-2-semen.protsenko@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Some ARM64 Exynos chips are capable to control PLL clocks automatically.
For those chips, whether the PLL is controlled automatically or manually
is chosen in PLL_CON1 register with next bits:
[28] ENABLE_AUTOMATIC_CLKGATING
[1] MANUAL_PLL_CTRL
[0] AUTO_PLL_CTRL
The bl2 bootloader sets 0x10000001 value for some PLL_CON1 registers,
which means any attempt to control those PLLs manually (e.g.
disabling/enabling those PLLs or changing MUX parent clocks) would lead
to PLL lock timeout with error message like this:
Could not lock PLL ...
At the moment, all Samsung clock drivers implement manual clock control.
So in order to make it possible to control PLLs, corresponding PLL_CON1
registers should be set to 0x2 first.
Some older ARM64 chips don't implement the automatic clock control
though. It also might be desirable to configure some PLLs for manual
control, while keeping the default configuration for the rest. So it'd
convenient to choose this PLL mode for each CMU separately. Introduce
.manual_plls field to CMU structure to choose the PLL control mode.
Because it'll be initialized with "false" in all existing CMU
structures by default, it won't affect any existing clock drivers,
allowing for this feature to be enabled gradually when it's needed with
no change for the rest of users. In case .manual_plls is set, set
PLL_CON1 registers to manual control, akin to what's already done for
gate clocks in exynos_arm64_init_clocks(). Of course, PLL_CON1 registers
should be added to corresponding struct samsung_cmu_info::clk_regs array
to make sure they get initialized.
No functional change. This patch adds a feature, but doesn't enable it
for any users.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Link: https://lore.kernel.org/r/20240301015118.30072-1-semen.protsenko@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
The init sequence specifies the 0x11 and 0x29 dsi commands, which are
the exit-sleep and display-on commands.
In the actual prepare step the driver already uses the appropriate
function calls for those, so drop the duplicates.
Fixes: e5f9d54341 ("drm/panel: ltk050h3146w: add support for Leadtek LTK050H3148W-CTA6 variant")
Signed-off-by: Heiko Stuebner <heiko.stuebner@cherry.de>
Reviewed-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240320131232.327196-2-heiko@sntech.de
Similar to other variants, the LTK050H3148W wants to run in video mode
when displaying data. So far only the Synopsis DSI driver was using this
panel and it is always switching to video mode, independent of this flag
being set.
Other DSI drivers might handle this differently, so add the flag.
Fixes: e5f9d54341 ("drm/panel: ltk050h3146w: add support for Leadtek LTK050H3148W-CTA6 variant")
Signed-off-by: Heiko Stuebner <heiko.stuebner@cherry.de>
Reviewed-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Acked-by: Jessica Zhang <quic_jesszhan@quicinc.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240320131232.327196-1-heiko@sntech.de
The physical address on the MT8188 platform is larger than 32 bits,
change the type from unsigned int to dma_addr_t to be able to access
the high bits of the address.
Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Sebastian Fricke <sebastian.fricke@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Add a lock for the ctx_list, to avoid accessing a NULL pointer
within the 'vpu_enc_ipi_handler' function when the ctx_list has
been deleted due to an unexpected behavior on the SCP IP block.
Fixes: 1972e32431 ("media: mediatek: vcodec: Fix possible invalid memory access for encoder")
Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com>
Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Sebastian Fricke <sebastian.fricke@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The VP9 bitstream uses superframes, which each contain 8 sub-frames,
enable accessing the last superframe by increasing the range of the index
vaidation as the maximum number of superframes is 8 and not 7, so that the
last sub-frame can be decoded normally with the stateful VP9 decoder.
Signed-off-by: Irui Wang <irui.wang@mediatek.com>
Signed-off-by: Sebastian Fricke <sebastian.fricke@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Commit 11e5ea5242 ("KVM: arm64: Use helpers to classify exception
types reported via ESR") tried to abstract the translation fault
check when handling an out-of IPA space condition, but incorrectly
replaced it with a permission fault check.
Restore the previous translation fault check.
Fixes: 11e5ea5242 ("KVM: arm64: Use helpers to classify exception types reported via ESR")
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Wujie Duan <wjduan@linx-info.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/kvmarm/864jd3269g.wl-maz@kernel.org/
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
Programming PMU events in the host that count during guest execution is
a feature supported by perf, e.g.
perf stat -e cpu_cycles:G ./lkvm run
While this works for VHE, the guest/host event bitmaps are not carried
through to the hypervisor in the nVHE configuration. Make
kvm_pmu_update_vcpu_events() conditional on whether or not _hardware_
supports PMUv3 rather than if the vCPU as vPMU enabled.
Cc: stable@vger.kernel.org
Fixes: 84d751a019 ("KVM: arm64: Pass pmu events to hyp via vcpu")
Reviewed-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20240305184840.636212-3-oliver.upton@linux.dev
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
When TME is disabled by BIOS, the dmesg output is:
x86/tme: not enabled by BIOS
... and TME functionality is not enabled by the kernel, but the TME feature
is still shown in /proc/cpuinfo.
Clear it.
[ mingo: Clarified changelog ]
Signed-off-by: Bingsong Si <sibs@chinatelecom.cn>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: "Huang, Kai" <kai.huang@intel.com>
Link: https://lore.kernel.org/r/20240311071938.13247-1-sibs@chinatelecom.cn
The Alpha blending for 30 bit RGB/BGR are not
functioning properly for rk3568/rk3588, so remove
it from the format list.
Fixes: bfd8a5c228 ("drm/rockchip: vop2: Add more supported 10bit formats")
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20240304100952.3592984-1-andyshrk@163.com
Lockdep detects a possible deadlock as listed below. This is because it
detects the IA55 interrupt controller .irq_eoi() API is called from
interrupt context while configuration-specific API (e.g., .irq_enable())
could be called from process context on resume path (by calling
rzg2l_gpio_irq_restore()). To avoid this, protect the call of
rzg2l_gpio_irq_enable() with spin_lock_irqsave()/spin_unlock_irqrestore().
With this the same approach that is available in __setup_irq() is mimicked
to pinctrl IRQ resume function.
Below is the lockdep report:
WARNING: inconsistent lock state
6.8.0-rc5-next-20240219-arm64-renesas-00030-gb17a289abf1f #90 Not tainted
--------------------------------
inconsistent {IN-HARDIRQ-W} -> {HARDIRQ-ON-W} usage.
str_rwdt_t_001./159 [HC0[0]:SC0[0]:HE1:SE1] takes:
ffff00000b001d70 (&rzg2l_irqc_data->lock){?...}-{2:2}, at: rzg2l_irqc_irq_enable+0x60/0xa4
{IN-HARDIRQ-W} state was registered at:
lock_acquire+0x1e0/0x310
_raw_spin_lock+0x44/0x58
rzg2l_irqc_eoi+0x2c/0x130
irq_chip_eoi_parent+0x18/0x20
rzg2l_gpio_irqc_eoi+0xc/0x14
handle_fasteoi_irq+0x134/0x230
generic_handle_domain_irq+0x28/0x3c
gic_handle_irq+0x4c/0xbc
call_on_irq_stack+0x24/0x34
do_interrupt_handler+0x78/0x7c
el1_interrupt+0x30/0x5c
el1h_64_irq_handler+0x14/0x1c
el1h_64_irq+0x64/0x68
_raw_spin_unlock_irqrestore+0x34/0x70
__setup_irq+0x4d4/0x6b8
request_threaded_irq+0xe8/0x1a0
request_any_context_irq+0x60/0xb8
devm_request_any_context_irq+0x74/0x104
gpio_keys_probe+0x374/0xb08
platform_probe+0x64/0xcc
really_probe+0x140/0x2ac
__driver_probe_device+0x74/0x124
driver_probe_device+0x3c/0x15c
__driver_attach+0xec/0x1c4
bus_for_each_dev+0x70/0xcc
driver_attach+0x20/0x28
bus_add_driver+0xdc/0x1d0
driver_register+0x5c/0x118
__platform_driver_register+0x24/0x2c
gpio_keys_init+0x18/0x20
do_one_initcall+0x70/0x290
kernel_init_freeable+0x294/0x504
kernel_init+0x20/0x1cc
ret_from_fork+0x10/0x20
irq event stamp: 69071
hardirqs last enabled at (69071): [<ffff800080e0dafc>] _raw_spin_unlock_irqrestore+0x6c/0x70
hardirqs last disabled at (69070): [<ffff800080e0cfec>] _raw_spin_lock_irqsave+0x7c/0x80
softirqs last enabled at (67654): [<ffff800080010614>] __do_softirq+0x494/0x4dc
softirqs last disabled at (67645): [<ffff800080015238>] ____do_softirq+0xc/0x14
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&rzg2l_irqc_data->lock);
<Interrupt>
lock(&rzg2l_irqc_data->lock);
*** DEADLOCK ***
4 locks held by str_rwdt_t_001./159:
#0: ffff00000b10f3f0 (sb_writers#4){.+.+}-{0:0}, at: vfs_write+0x1a4/0x35c
#1: ffff00000e43ba88 (&of->mutex){+.+.}-{3:3}, at: kernfs_fop_write_iter+0xe8/0x1a8
#2: ffff00000aa21dc8 (kn->active#40){.+.+}-{0:0}, at: kernfs_fop_write_iter+0xf0/0x1a8
#3: ffff80008179d970 (system_transition_mutex){+.+.}-{3:3}, at: pm_suspend+0x9c/0x278
stack backtrace:
CPU: 0 PID: 159 Comm: str_rwdt_t_001. Not tainted 6.8.0-rc5-next-20240219-arm64-renesas-00030-gb17a289abf1f #90
Hardware name: Renesas SMARC EVK version 2 based on r9a08g045s33 (DT)
Call trace:
dump_backtrace+0x94/0xe8
show_stack+0x14/0x1c
dump_stack_lvl+0x88/0xc4
dump_stack+0x14/0x1c
print_usage_bug.part.0+0x294/0x348
mark_lock+0x6b0/0x948
__lock_acquire+0x750/0x20b0
lock_acquire+0x1e0/0x310
_raw_spin_lock+0x44/0x58
rzg2l_irqc_irq_enable+0x60/0xa4
irq_chip_enable_parent+0x1c/0x34
rzg2l_gpio_irq_enable+0xc4/0xd8
rzg2l_pinctrl_resume_noirq+0x4cc/0x520
pm_generic_resume_noirq+0x28/0x3c
genpd_finish_resume+0xc0/0xdc
genpd_resume_noirq+0x14/0x1c
dpm_run_callback+0x34/0x90
device_resume_noirq+0xa8/0x268
dpm_noirq_resume_devices+0x13c/0x160
dpm_resume_noirq+0xc/0x1c
suspend_devices_and_enter+0x2c8/0x570
pm_suspend+0x1ac/0x278
state_store+0x88/0x124
kobj_attr_store+0x14/0x24
sysfs_kf_write+0x48/0x6c
kernfs_fop_write_iter+0x118/0x1a8
vfs_write+0x270/0x35c
ksys_write+0x64/0xec
__arm64_sys_write+0x18/0x20
invoke_syscall+0x44/0x108
el0_svc_common.constprop.0+0xb4/0xd4
do_el0_svc+0x18/0x20
el0_svc+0x3c/0xb8
el0t_64_sync_handler+0xb8/0xbc
el0t_64_sync+0x14c/0x150
Fixes: 254203f9a9 ("pinctrl: renesas: rzg2l: Add suspend/resume support")
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20240320104230.446400-2-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
On the RZ/G3S SMARC platform, the 'input' property is utilized in
gpio-hog nodes, and the 'output-enable' property is used for ETH0/1 TXC
pins. Update the binding documentation to include these properties,
addressing the following dtbs_check warnings:
arch/arm64/boot/dts/renesas/r9a08g045s33-smarc.dtb: pinctrl@11030000: key-1-gpio-hog: 'anyOf' conditional failed, one must be fixed:
'input' does not match any of the regexes: 'pinctrl-[0-9]+'
arch/arm64/boot/dts/renesas/r9a08g045s33-smarc.dtb: pinctrl@11030000: eth0: 'anyOf' conditional failed, one must be fixed:
'output-enable' does not match any of the regexes: 'pinctrl-[0-9]+'
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20240313083828.5048-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add DT binding documentation for System Controller (SYS) found on
RZ/V2H(P) ("R9A09G057") SoC's.
SYS block contains the SYS_LSI_DEVID register which can be used to
retrieve SoC version information.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro.jz@renesas.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20240227232531.218159-3-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Enable the config for the Renesas DA9062 PMIC and the built-in RTC, GPIO
and ONKEY drivers as it is populated on the RZ/G2UL SMARC EVK
development board.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20240227130010.45361-1-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Enable the RZ/G2L display unit DRM drivers used on the RZ/{G2L,G2LC,V2L}
SMARC EVK development boards.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20240223123646.245655-1-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The r9a07g044_resets array describes the reset signals in this SoC and
does not change at runtime.
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20240320082831.9666-2-paul.barker.ct@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The r9a07g043_mod_clks and r9a07g043_resets arrays describe the module
clocks and reset signals (respectively) in this SoC and do not change at
runtime.
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20240320082831.9666-1-paul.barker.ct@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add the module clock used by the Thermal Sensor/Chip Internal Voltage
Monitor/Core Voltage Monitor (THS/CIVM/CVM) on the Renesas R-Car V4M
(R8A779H0) SoC.
Based on a patch in the BSP by Cong Dang.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/befac3e8342cd552f580d34be863ef84403c541f.1709722056.git.geert+renesas@glider.be
The M2 (CRU main clock), M3 (LCDC Video Clock), and AT (Cortex-A55 Debug
clock) core clocks are only present on RZ/G2UL, not on RZ/Five.
Annotate this in the comments, like is already done for module clocks
and resets.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/ffcdcd479c76b92f67481836a33ec86e97f85634.1708944903.git.geert+renesas@glider.be
If channel for the given node is not found we return null from
get_channel_from_mode. Make sure we validate the return pointer
before using it in two of the missing places.
This was originally reported in [0]:
Found by Linux Verification Center (linuxtesting.org) with SVACE.
[0] https://lore.kernel.org/all/20240301190425.120605-1-m.lobanov@rosalinux.ru
Fixes: 2870b52bae ("greybus: lights: add lights implementation")
Reported-by: Mikhail Lobanov <m.lobanov@rosalinux.ru>
Suggested-by: Mikhail Lobanov <m.lobanov@rosalinux.ru>
Suggested-by: Alex Elder <elder@ieee.org>
Signed-off-by: Rui Miguel Silva <rmfrfs@gmail.com>
Link: https://lore.kernel.org/r/20240325221549.2185265-1-rmfrfs@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All Renesas R-Car Gen2 SoCs have Timer Units (TMU). Enable support for
them by selecting the SYS_SUPPORTS_SH_TMU gatekeeper config symbol.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/b7b9fdd6f517a8b29bf5754e7f083d3b71805130.1710865761.git.geert+renesas@glider.be
Add device nodes for the Timer Units (TMU) on the R-Mobile APE6 SoC,
and the clocks serving them.
Note that TMU channels 1 and 2 are not added, as their interrupts are
not wired to the interrupt controller for the AP-System Core (INTC-SYS),
only to the interrupt controller for the AP-Realtime Core (INTC-RT).
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/1a60832f3ba37afb4a5791f4e5db4610ab31beb3.1710864964.git.geert+renesas@glider.be
Add "interrupt-names" properties to SCIF nodes for clarity.
This allows us to update the DT bindings to mark the "interrupt-names"
property required for all SoCs which have multiple interrupts, and to
validate the DTBs using dtbs_check.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20240318174345.46824-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add device nodes for the Thermal Sensor/Chip Internal Voltage
Monitor/Core Voltage Monitor (THS/CIVM/CVM) and the various thermal
zones on the Renesas R-Car V4M (R8A779H0) SoC.
Add support for 2 TSC nodes of thermal.
Signed-off-by: Duy Nguyen <duy.nguyen.rh@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/d1f07c77943912145583d8916ba3ca65d143b1b1.1709722573.git.geert+renesas@glider.be
Enable PMIC DA9062 and the built-in RTC, GPIO and ONKEY modules on the
RZ/{G2UL,Five} SMARC EVK development boards.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20240226194715.427597-2-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The Eagle board supports an optional "Function expansion board".
The expansion board adds support for HDMI OUT, HDMI capture from two
different sources, and eMMC.
This change only adds support for the two HDMI capture sources.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20240224191902.2065733-1-niklas.soderlund+renesas@ragnatech.se
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The MT7530 switch after reset initialises with a core clock frequency that
works with a 25MHz XTAL connected to it. For 40MHz XTAL, the core clock
frequency must be set to 500MHz.
The mt7530_pll_setup() function is responsible of setting the core clock
frequency. Currently, it runs on MT7530 with 25MHz and 40MHz XTAL. This
causes MT7530 switch with 25MHz XTAL to egress and ingress frames
improperly.
Introduce a check to run it only on MT7530 with 40MHz XTAL.
The core clock frequency is set by writing to a switch PHY's register.
Access to the PHY's register is done via the MDIO bus the switch is also
on. Therefore, it works only when the switch makes switch PHYs listen on
the MDIO bus the switch is on. This is controlled either by the state of
the ESW_P1_LED_1 pin after reset deassertion or modifying bit 5 of the
modifiable trap register.
When ESW_P1_LED_1 is pulled high, PHY indirect access is used. That means
accessing PHY registers via the PHY indirect access control register of the
switch.
When ESW_P1_LED_1 is pulled low, PHY direct access is used. That means
accessing PHY registers via the MDIO bus the switch is on.
For MT7530 switch with 40MHz XTAL on a board with ESW_P1_LED_1 pulled high,
the core clock frequency won't be set to 500MHz, causing the switch to
egress and ingress frames improperly.
Run mt7530_pll_setup() after PHY direct access is set on the modifiable
trap register.
With these two changes, all MT7530 switches with 25MHz and 40MHz, and
P1_LED_1 pulled high or low, will egress and ingress frames properly.
Link: 4a5dd143f2/linux-mt/drivers/net/ethernet/mediatek/gsw_mt7623.c (L1039)
Fixes: b8f126a8d5 ("net-next: dsa: add dsa support for Mediatek MT7530 switch")
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Link: https://lore.kernel.org/r/20240320-for-net-mt7530-fix-25mhz-xtal-with-direct-phy-access-v1-1-d92f605f1160@arinc9.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Convert the minix filesystem to use the new mount API.
Tested using mount and remount on minix device.
Signed-off-by: Bill O'Donnell <bodonnel@redhat.com>
Link: https://lore.kernel.org/r/20240307163325.998723-1-bodonnel@redhat.com
Acked-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: Christian Brauner <brauner@kernel.org>
Convert the tracefs filesystem to the new internal mount API as the old
one will be obsoleted and removed. This allows greater flexibility in
communication of mount parameters between userspace, the VFS and the
filesystem.
See Documentation/filesystems/mount_api.txt for more information.
Signed-off-by: David Howells <dhowells@redhat.com>
Co-developed-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
[sandeen: forward port to modern kernel, fix remounting]
Link: https://lore.kernel.org/r/536e99d3-345c-448b-adee-a21389d7ab4b@redhat.com
cc: Steven Rostedt <rostedt@goodmis.org>
cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Christian Brauner <brauner@kernel.org>
Convert the debugfs filesystem to the new internal mount API as the old
one will be obsoleted and removed. This allows greater flexibility in
communication of mount parameters between userspace, the VFS and the
filesystem.
See Documentation/filesystems/mount_api.txt for more information.
Signed-off-by: David Howells <dhowells@redhat.com>
Co-developed-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
[sandeen: forward port to modern kernel, fix remounting]
Link: https://lore.kernel.org/r/49d1f108-46e3-443f-85a3-6dd730c5d076@redhat.com
cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cc: Rafael J. Wysocki <rafael@kernel.org>
Signed-off-by: Christian Brauner <brauner@kernel.org>
The original mount API conversion inexplicably left out the change
from ->remount_fs to ->reconfigure; do that now.
Fixes: 7ab2fa7693 ("vfs: Convert openpromfs to use the new mount API")
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Link: https://lore.kernel.org/r/90b968aa-c979-420f-ba37-5acc3391b28f@redhat.com
Signed-off-by: Christian Brauner <brauner@kernel.org>
Convert the qnx6 filesystem to use the new mount API.
Mostly untested, since there is no qnx6 fs image readily available.
Testing did include parsing of the mmi_fs option.
Signed-off-by: Bill O'Donnell <bodonnel@redhat.com>
Link: https://lore.kernel.org/r/20240302165714.859504-1-bodonnel@redhat.com
Signed-off-by: Christian Brauner <brauner@kernel.org>
Add the "ref-cycles" event for AMD processors based on Zen 4 and later
microarchitectures. The backing event is based on PMCx120 which counts
cycles not in halt state in P0 frequency (same as MPERF).
Signed-off-by: Sandipan Das <sandipan.das@amd.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Ian Rogers <irogers@google.com>
Link: https://lore.kernel.org/r/089155f19f7c7e65aeb1caa727a882e2ca9b8b04.1711352180.git.sandipan.das@amd.com